Results for igt@kms_cursor_legacy@basic-busy-flip-before-cursor-atomic

Result: Skip

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gb7d168f61 (x86_64) (Linux: 6.4.0-rc7-linus-v6.4-rc7-g45a3e24f65e9+ x86_64)
Out	Opened device: /dev/dri/card0 No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. Subtest basic-busy-flip-before-cursor-atomic: SKIP (0.000s) No valid crtc/connector combinations found.
Err	Subtest basic-busy-flip-before-cursor-atomic: SKIP (0.000s)
Dmesg	<6> [111.119547] [IGT] kms_cursor_legacy: executing <7> [111.123035] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [111.123858] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [111.124258] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [111.131842] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [111.131867] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [111.132095] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.132615] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [111.133137] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [111.133739] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [111.134628] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [111.134927] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [111.135828] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.137507] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.138924] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.140583] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.142425] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.144247] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.146016] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.147822] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.149204] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.150066] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [111.150839] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [111.151506] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [111.152022] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [111.152244] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [111.152494] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [111.152689] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [111.153365] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.153603] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [111.154505] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [111.154526] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [111.154718] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.155269] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.155508] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [111.156273] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [111.156292] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [111.156476] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.209013] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [111.225460] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [111.225468] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [111.225646] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [111.241575] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [111.241582] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [111.241759] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.241988] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [111.242689] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [111.242710] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [111.242934] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.243463] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [111.244054] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [111.244645] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [111.245365] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [111.245558] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [111.246573] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.248159] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.249764] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.251338] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.253104] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.254836] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.256590] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.258434] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.260083] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.261044] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [111.261974] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [111.262644] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [111.263148] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [111.263397] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [111.263587] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [111.263769] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [111.264433] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.264719] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [111.264803] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [111.264828] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [111.265083] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.265592] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.265810] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [111.265862] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [111.265885] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [111.266153] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.318010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [111.334455] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [111.334464] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [111.334644] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [111.350531] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [111.350538] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [111.350712] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.350944] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <6> [111.351818] [IGT] kms_cursor_legacy: exiting, ret=77 <7> [111.352352] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

Created at 2023-06-18 23:06:06