Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Igt-Version |
IGT-Version: 1.27.1-gb7d168f61 (x86_64) (Linux: 6.4.0-rc7-linus-v6.4-rc7-g45a3e24f65e9+ x86_64) |
| Out |
Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x76/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa2d/0xd10 [i915] intel_atomic_commit+0x380/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 0 Subtest basic-rte: SUCCESS (1.678s) i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x76/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa2d/0xd10 [i915] intel_atomic_commit+0x380/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 0 |
| Err |
Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.678s) |
| Dmesg |
<6> [97.055154] Console: switching to colour dummy device 80x25
<6> [97.055493] [IGT] i915_pm_rpm: executing
<6> [97.058666] [IGT] i915_pm_rpm: starting subtest basic-rte
<7> [97.058702] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [97.059063] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1]
<7> [97.059077] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [97.059198] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.059937] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.060062] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] disconnected
<7> [97.060123] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [97.060132] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [97.060246] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.061125] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.061254] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [97.061311] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2]
<7> [97.061333] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [97.061436] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.062336] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.062453] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] disconnected
<7> [97.062505] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3]
<7> [97.062514] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [97.062618] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.063624] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.063741] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] disconnected
<7> [97.063793] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2]
<7> [97.063802] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [97.063920] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.064718] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.064834] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2] disconnected
<7> [97.064888] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4]
<7> [97.064897] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [97.064993] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.065924] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.066096] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] disconnected
<7> [97.071822] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1]
<7> [97.071834] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [97.071950] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.072666] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.072805] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] disconnected
<7> [97.073159] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [97.073168] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [97.073293] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.073992] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.074108] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [97.074495] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2]
<7> [97.074504] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [97.074611] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.075400] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.075524] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] disconnected
<7> [97.075862] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3]
<7> [97.075872] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [97.075973] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.076687] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.076806] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] disconnected
<7> [97.077152] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2]
<7> [97.077161] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [97.077296] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.077986] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.078109] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2] disconnected
<7> [97.078475] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4]
<7> [97.078484] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [97.078588] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.079298] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.079427] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] disconnected
<7> [97.079875] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1]
<7> [97.079885] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [97.079989] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.080695] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.080817] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] disconnected
<7> [97.080837] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [97.080846] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [97.080948] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.081890] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.082012] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [97.082031] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2]
<7> [97.082040] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [97.082140] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.083079] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.083197] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] disconnected
<7> [97.083216] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3]
<7> [97.083225] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [97.083341] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.084278] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.084398] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] disconnected
<7> [97.084417] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2]
<7> [97.084426] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [97.084531] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.085471] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.085589] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2] disconnected
<7> [97.085609] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4]
<7> [97.085618] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [97.085726] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [97.086665] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [97.086782] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] disconnected
<7> [98.088595] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.093940] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.096260] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.097410] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.097552] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.097685] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.097816] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.097949] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.098082] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.098214] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.098366] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.098497] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.098627] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.098770] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.098958] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.100286] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.100447] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.100707] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.100938] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.101211] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.125431] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.125856] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.126394] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.126910] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.127823] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.128285] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.128683] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.129139] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.130908] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.131192] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.144748] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.145961] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [98.147058] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.148309] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [98.147306] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.149490] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.149639] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [98.149740] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.149876] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.150644] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.151865] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.152003] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.152131] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.152272] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.152397] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.152523] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.152645] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.152769] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.152897] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.153017] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.153133] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.153274] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.153400] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.154622] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.154749] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.155330] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [98.157054] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.159477] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.160618] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.160755] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.160881] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.161008] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.161140] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.161290] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.161437] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.161565] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.161685] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.161803] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.161936] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.162114] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.163670] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.163827] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.163982] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.164090] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.164227] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.188413] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.188642] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.188914] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.189209] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.189894] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.190343] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.190672] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.191077] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.192494] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.192711] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.204948] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.206156] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.206316] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.206482] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.207259] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.208520] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.208650] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.208772] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.208894] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.209015] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.209141] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.209271] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.209400] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.209525] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.209641] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.209759] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.209874] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.209983] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.211195] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.211342] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.212156] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [98.212248] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [98.213668] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.216023] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.217190] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.217341] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.217467] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.217591] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.217715] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.217841] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.217966] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.218090] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.218215] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.218349] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.218498] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.218697] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.220220] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.220400] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.220557] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.220669] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.220807] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.245500] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.245746] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.246034] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.246378] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.247083] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.247390] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.247675] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.247993] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.249263] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.249472] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.262909] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.264119] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.264238] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.265247] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.265402] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [98.265417] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [98.265526] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.266448] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.266625] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [98.266702] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.266829] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.267609] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.268836] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.268974] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.269097] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.269225] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.269370] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.269505] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.269629] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.269759] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.269885] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.270009] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.270125] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.270254] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.270379] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.271594] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.271718] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.272314] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [98.272316] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [98.274029] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.276418] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.277591] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.277750] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.277893] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.278025] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.278153] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.278298] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.278428] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.278557] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.278678] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.278800] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.278942] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.279167] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.280724] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.280882] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.281041] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.281152] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.281309] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.305929] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.306146] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.306445] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.306722] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.307514] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.307770] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.308008] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.308324] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.309566] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.309791] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.323235] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.324437] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.324541] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.325582] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.325764] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [98.325779] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [98.325882] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.326761] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.326896] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [98.326982] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.327246] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.327993] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.329222] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.329378] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.329509] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.329638] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.329768] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.329900] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.330030] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.330164] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.330301] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.330431] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.330565] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.330687] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.330802] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.332020] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.332156] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.332760] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [98.335679] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.338070] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.339209] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.339355] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.339485] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.339607] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.339730] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.339852] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.339974] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.340100] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.340220] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.340352] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.340500] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.340690] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.342235] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.342405] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.342562] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.342671] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.342807] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.367466] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.367710] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.367998] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.368339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.369074] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.369390] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.369651] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.369967] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.371377] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.371583] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.385004] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.386214] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.386337] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.387359] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.387488] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [98.387506] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [98.387606] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.388537] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.388657] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [98.388669] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [98.388774] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.389729] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.389860] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [98.389872] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [98.389972] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.390927] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.391050] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [98.391061] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [98.391167] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.392110] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.392228] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [98.392249] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [98.392358] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.393312] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.393434] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [98.393445] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [98.393547] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.394507] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.394622] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [98.394635] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.396910] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.399345] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.400475] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.400615] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.400741] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.400865] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.400994] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.401118] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.401250] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.401383] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.401509] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.401632] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.401772] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.401973] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.403285] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.403445] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.403600] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.403704] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.403839] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.433453] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [98.445982] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.446519] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.447034] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.447618] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.448558] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.449050] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.449591] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.450151] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.452430] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.452914] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.467889] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.470197] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.470350] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.470493] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.471395] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.472617] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.472748] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.472873] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.472999] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.473124] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.473259] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.473387] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.473523] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.473640] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.473758] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.473881] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.474018] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.474131] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.475368] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.475490] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.476252] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [98.477785] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.480175] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.481349] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.481485] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.481616] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.481743] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.481869] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.481996] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.482117] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.482253] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.482389] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.482515] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.482655] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.482862] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.484289] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.484449] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.484602] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.484711] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.484848] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.509503] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.509778] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.510094] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.510489] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.511260] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.511593] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.511904] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.512296] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.513769] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.514010] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.527484] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.528683] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.528849] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.528981] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.529788] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.531015] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.531150] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.531294] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.531433] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.531558] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.531681] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.531805] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.531929] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.532053] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.532177] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.532303] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.532434] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.532549] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.533769] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.533902] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.534453] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [98.534458] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [98.536202] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.538589] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.539793] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.539935] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.540064] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.540192] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.540330] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.540460] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.540579] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.540701] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.540822] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.540946] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.541082] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.541285] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.542832] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.542987] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.543143] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.543262] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.543405] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.568067] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.568382] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.568670] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.568984] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.569710] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.570162] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.570531] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.570922] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.572488] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.572741] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.587350] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.588556] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.588660] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.589704] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.589864] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [98.589952] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.590077] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.590850] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.592075] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.592216] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.592357] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.592489] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.592618] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.592744] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.592867] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.592993] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.593120] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.593254] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.593385] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.593499] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.593610] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.594828] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.594994] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [98.594992] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [98.595133] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.596032] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.596165] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [98.596243] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.596373] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.597204] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.598432] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.598578] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.598716] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.598857] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.598998] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.599135] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.599275] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.599423] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.599553] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.599681] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.599809] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.599932] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.600047] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.601270] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.601446] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.601540] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [98.603720] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.606103] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.607266] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.607407] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.607531] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.607655] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.607779] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.607902] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.608025] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.608148] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.608283] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.608410] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.608553] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.608735] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.610285] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.610448] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.610606] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.610714] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.610847] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.635429] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.635573] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.635741] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.635927] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.636460] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.636673] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.636921] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.637156] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.638065] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.638206] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.651519] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.652730] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.652837] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.653859] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.653989] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [98.654002] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [98.654108] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.655053] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.655172] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [98.655185] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [98.655308] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.656243] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.656378] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [98.656389] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [98.656489] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.657437] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.657554] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [98.657570] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [98.657674] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.658630] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.658752] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [98.658764] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [98.658871] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.659826] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.659943] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [98.659955] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [98.660062] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.661023] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.661145] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [98.661156] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [98.661279] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.662207] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.662356] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [98.662368] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [98.662482] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.663417] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.663539] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [98.663550] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [98.663658] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.664606] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.664730] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [98.664743] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.667013] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.669436] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.670574] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.670710] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.670841] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.670972] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.671099] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.671226] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.671367] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.671498] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.671621] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.671743] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.671884] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.672086] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.673623] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.673783] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.673936] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.674048] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.674185] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.714070] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.714590] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.715127] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.715726] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.716679] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.717192] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.717717] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.718269] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.719473] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.719589] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.731734] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.732947] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [98.734047] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.734168] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.735275] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [98.735289] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [98.735455] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [98.735467] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [98.736466] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [98.736573] [IGT] i915_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [98.736593] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [98.736601] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [98.736839] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.736981] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.737676] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.738896] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.739038] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.739175] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.739322] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.739462] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.739590] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.739715] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.739855] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.739989] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.740130] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.740307] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.740432] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.740540] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.741753] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.741906] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [98.741883] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.744228] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.746581] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.747748] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.747892] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.748020] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.748152] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.748291] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.748428] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.748561] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.748691] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.748811] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.748932] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.749078] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.749274] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.750827] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.750990] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.751150] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.751277] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.751422] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.776090] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.776339] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.776613] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.776896] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.777533] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.777916] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.778175] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.778578] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.780040] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.780268] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.793696] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.794899] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.795036] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.795164] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.796001] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.797233] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.797378] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.797502] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.797627] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.797754] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.797880] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.798007] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.798135] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.798267] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.798408] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.798538] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.798733] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.798973] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.800193] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.800328] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.801127] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [98.801207] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [98.802623] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.805019] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.806188] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.806335] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.806461] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.806587] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.806713] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.806839] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.806964] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.807094] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.807221] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.807355] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.807500] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.807705] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.809241] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.809408] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.809563] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.809676] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.809823] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.834492] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.834725] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.835010] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.835338] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.836051] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.836354] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.836626] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.836947] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.838243] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.838456] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.851828] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.853038] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.853153] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.854172] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.854315] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [98.854331] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [98.854449] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.855361] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.855494] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [98.855510] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [98.855618] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.856552] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.856684] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [98.856706] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.858963] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.861372] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.862522] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.862669] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.862801] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.862934] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.863061] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.863192] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.863335] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.863479] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.863608] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.863740] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.863886] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.864078] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.865621] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.865787] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.865944] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.866061] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.866205] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.890923] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.891273] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.891666] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.892060] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.892925] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.893420] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.893853] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.894409] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.896104] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.896430] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.909967] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.911176] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.911363] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.911491] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.912280] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.913504] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.913641] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.913763] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.913883] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.914006] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.914129] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.914265] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.914407] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.914535] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.914659] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.914781] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.914893] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.915005] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.916221] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.916363] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.916964] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [98.918653] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.921058] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.922220] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.922410] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.922539] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.922660] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.922783] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.922905] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.923027] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.923154] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.923293] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.923440] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.923584] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.923768] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.925276] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.925444] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.925602] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.925714] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.925849] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [98.950535] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [98.950789] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [98.951095] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [98.951457] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [98.952171] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [98.952492] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.952775] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [98.953095] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [98.954483] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.954711] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.966978] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [98.968184] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [98.968338] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [98.968480] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [98.969286] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.970517] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.970661] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.970786] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.970911] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.971039] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.971163] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.971293] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.971427] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.971554] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.971679] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.971798] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [98.971915] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [98.972020] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [98.973236] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [98.973361] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [98.974355] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [98.975660] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [98.978077] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [98.979228] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.979385] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [98.979512] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.979634] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [98.979758] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.979881] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [98.980004] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.980132] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [98.980266] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.980399] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [98.980538] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [98.980742] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [98.982275] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [98.982437] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [98.982594] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [98.982704] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [98.982840] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [99.007707] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [99.007953] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [99.008285] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [99.008623] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [99.009511] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [99.009830] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [99.010089] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [99.010500] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [99.011921] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [99.012143] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [99.024396] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [99.025597] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [99.025723] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.026726] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.026859] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [99.026872] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [99.026989] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.027910] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.028034] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [99.028046] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [99.028150] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.029113] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.029244] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [99.029259] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [99.029370] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.030314] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.030442] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [99.030453] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [99.030562] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.031493] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.031620] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [99.031635] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [99.031746] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.032687] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.032823] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [99.032842] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [99.032952] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.033885] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.034012] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [99.034025] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [99.034135] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.035078] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.035200] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [99.035212] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [99.035331] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.036275] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.036407] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [99.036422] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [99.036530] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.037472] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.037604] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [99.037618] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [99.037727] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.038655] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.038785] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [99.038800] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [99.038909] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.039853] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.039986] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [99.039999] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [99.042268] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [99.044658] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [99.045826] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.045976] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [99.046114] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.046255] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [99.046393] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.046523] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [99.046651] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.046786] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [99.046914] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.047043] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [99.047198] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [99.047442] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [99.048934] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [99.049103] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.049269] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [99.049396] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [99.049539] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [99.101342] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [99.102015] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [99.102879] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [99.103775] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [99.105077] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [99.105886] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [99.106188] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [99.106542] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [99.107270] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [99.107397] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [99.121762] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [99.124135] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [99.125327] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [99.125540] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.126199] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [99.126539] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [99.127745] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.127898] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [99.128031] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.128164] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [99.128309] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.128449] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [99.128586] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.128729] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [99.128869] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.129002] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [99.129125] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [99.129256] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [99.129404] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [99.129396] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [99.129417] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [99.129556] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [99.129566] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [99.129726] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [99.129740] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [99.129886] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [99.129897] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [99.130028] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [99.130039] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [99.130164] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [99.141430] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [99.141604] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [99.141728] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_2 forced on (bios:1 driver:0 kvmr:0 debug:0)
<7> [99.141841] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [99.141959] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [99.142069] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [99.143288] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.185125] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.185867] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [99.187191] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [99.188543] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.189186] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [99.189859] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.190495] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [99.191039] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.191828] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [99.192574] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.193152] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [99.193732] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.194262] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [99.194880] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [99.195374] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [99.195835] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [99.197351] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [99.198166] [IGT] i915_pm_rpm: exiting, ret=0
<7> [99.199929] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.200187] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [99.201093] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [99.202352] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.202617] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [99.202878] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.203073] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [99.203259] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.203437] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [99.203602] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.203773] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [99.203939] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.204103] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [99.204344] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [99.204493] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [99.204624] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [99.205853] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [99.206079] Console: switching to colour frame buffer device 128x48
<7> [99.206407] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.206542] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [99.207224] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [99.208487] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.208643] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [99.208781] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.208909] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [99.209032] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.209159] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [99.209294] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.209431] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [99.209555] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [99.209678] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [99.209804] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [99.209921] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [99.210030] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [99.211273] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
|