Results for igt@i915_module_load@reload

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-gb7d168f61 (x86_64) (Linux: 6.4.0-rc7-linus-v6.4-rc7-g45a3e24f65e9+ x86_64)
Out 
Starting subtest: reload
Opened device: /dev/dri/card0
Subtest reload: SUCCESS (2.755s)
Err 
Starting subtest: reload
Subtest reload: SUCCESS (2.755s)
Dmesg
<6> [151.171091] [IGT] i915_module_load: executing
<6> [151.173283] [IGT] i915_module_load: starting subtest reload
<7> [151.222122] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [151.222275] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [151.222398] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [151.222533] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [151.222827] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [151.223272] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [151.223454] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [151.223828] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [151.225572] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [151.225683] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [151.229421] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [151.230439] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [151.230785] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [151.231036] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [151.231181] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [151.231876] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [151.232018] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [151.232175] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [151.232305] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [151.232424] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [151.232529] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [151.232752] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [151.232773] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [151.232920] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 1
<7> [151.232936] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [151.233107] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [151.233092] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [151.233125] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [151.233335] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [151.246272] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [151.246389] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [151.246491] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [151.246586] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [151.246995] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [151.275316] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [151.275639] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [151.276175] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [151.276716] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [151.276990] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [151.277282] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [151.277533] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [151.277750] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [151.277984] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [151.291182] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [151.291413] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [151.291617] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [151.291813] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [151.292365] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [151.351959] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [151.352217] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [151.352533] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [151.352717] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [151.352873] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [151.353023] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [151.353228] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [151.353357] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [151.353484] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [151.373637] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port A
<7> [151.373811] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port A
<7> [151.373954] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port A
<7> [151.374115] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port A
<7> [151.374258] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [151.374398] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [151.374541] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [151.374684] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [151.374820] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [151.374955] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [151.375103] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [151.375241] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [151.375427] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [151.375596] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [151.375739] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [151.375885] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [151.376029] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port E
<7> [151.376188] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port E
<7> [151.376333] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port E
<7> [151.376470] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port E
<7> [151.376596] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port F
<7> [151.376724] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port F
<7> [151.376849] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port F
<7> [151.376975] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port F
<7> [151.377107] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port G
<7> [151.377230] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port G
<7> [151.377344] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port G
<7> [151.377454] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port G
<7> [151.377564] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port H
<7> [151.377672] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port H
<7> [151.377778] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port H
<7> [151.377883] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port H
<7> [151.377986] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port I
<7> [151.378096] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port I
<7> [151.378200] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port I
<7> [151.378297] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port I
<7> [151.378714] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [151.378827] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [151.378930] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [151.379035] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [151.379474] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [151.528892] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind
<7> [151.598018] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [151.598932] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [151.599939] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [151.600875] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [151.601567] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [151.602179] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [151.602679] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [151.603178] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [151.603605] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [151.603992] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_B
<7> [151.604410] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_C
<7> [151.604751] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_D
<7> [151.621516] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [151.679319] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [152.624303] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K
<7> [152.624465] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:yes huc:yes slpc:yes)
<7> [152.624609] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Alder Lake PCH
<7> [152.624755] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [152.625153] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 19200 kHz
<7> [152.625477] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0005, instances: 0005
<7> [152.625575] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001
<7> [152.625877] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [152.625972] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [152.626051] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M
<6> [152.626145] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [152.626150] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [152.626407] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [152.626428] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x0000000050200087
<7> [152.626585] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K
<7> [152.626815] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x44a07018
<7> [152.626954] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0
<7> [152.627062] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [152.627196] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [152.627306] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [152.627422] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (RVDA)
<7> [152.627547] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 4
<7> [152.627647] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [152.627733] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2401 tRP=24 tRDPRE=20 tRAS=52 tRCD=24 tRC=76
<7> [152.627865] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=4801 tRP=44 tRDPRE=28 tRAS=104 tRCD=44 tRC=148
<7> [152.627987] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=5201 tRP=48 tRDPRE=28 tRAS=112 tRCD=48 tRC=160
<7> [152.628129] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 3: DCLK=5201 tRP=48 tRDPRE=28 tRAS=112 tRCD=48 tRC=160
<7> [152.628236] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 0: CLK=32
<7> [152.628338] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 1: CLK=39
<7> [152.628438] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 2: CLK=48
<7> [152.628546] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 0: num_planes=0 deratedbw=16956
<7> [152.628652] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 1: num_planes=0 deratedbw=23981
<7> [152.628755] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 2: num_planes=0 deratedbw=24772
<7> [152.628855] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 3: num_planes=0 deratedbw=24772
<7> [152.628963] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 0: num_planes=0 bw=34133
<7> [152.629068] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 1: num_planes=0 bw=41600
<7> [152.629184] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 2: num_planes=0 bw=51200
<7> [152.629297] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 0: num_planes=4 deratedbw=21855
<7> [152.629401] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 1: num_planes=4 deratedbw=34500
<7> [152.629500] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 2: num_planes=4 deratedbw=36108
<7> [152.629611] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 3: num_planes=4 deratedbw=36108
<7> [152.629717] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 0: num_planes=4 bw=34133
<7> [152.629818] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 1: num_planes=4 bw=41600
<7> [152.629917] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 2: num_planes=4 bw=51200
<7> [152.630015] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 0: num_planes=0 deratedbw=25544
<7> [152.630141] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 1: num_planes=0 deratedbw=38000
<7> [152.630251] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 2: num_planes=0 deratedbw=38000
<7> [152.630355] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 3: num_planes=0 deratedbw=38000
<7> [152.630457] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 0: num_planes=0 bw=34133
<7> [152.630556] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 1: num_planes=0 bw=41600
<7> [152.630655] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 2: num_planes=0 bw=51200
<7> [152.630761] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 0: num_planes=0 deratedbw=27900
<7> [152.630872] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 1: num_planes=0 deratedbw=38000
<7> [152.630977] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 2: num_planes=0 deratedbw=38000
<7> [152.631097] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 3: num_planes=0 deratedbw=38000
<7> [152.631210] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 0: num_planes=0 bw=34133
<7> [152.631320] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 1: num_planes=0 bw=41600
<7> [152.631426] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 2: num_planes=0 bw=51200
<7> [152.631529] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 0: num_planes=0 deratedbw=29248
<7> [152.631630] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 1: num_planes=0 deratedbw=38000
<7> [152.631733] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 2: num_planes=0 deratedbw=38000
<7> [152.631843] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 3: num_planes=0 deratedbw=38000
<7> [152.631949] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 0: num_planes=0 bw=34133
<7> [152.632059] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 1: num_planes=0 bw=41600
<7> [152.632184] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 2: num_planes=0 bw=51200
<7> [152.632297] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 0: num_planes=0 deratedbw=29972
<7> [152.632405] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 1: num_planes=0 deratedbw=38000
<7> [152.632509] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 2: num_planes=0 deratedbw=38000
<7> [152.632612] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 3: num_planes=0 deratedbw=38000
<7> [152.632714] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 0: num_planes=0 bw=34133
<7> [152.632820] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 1: num_planes=0 bw=41600
<7> [152.632923] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 2: num_planes=0 bw=51200
<7> [152.633847] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [152.634033] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT ALDERLAKE-P ", BDB version 251
<7> [152.634216] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 10, min size 7)
<7> [152.634380] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 395, min size 5)
<7> [152.634559] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 100, min size 100)
<7> [152.634742] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [152.634925] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 814, min size 812)
<7> [152.635112] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 34, min size 34)
<7> [152.635291] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Generating LFP data table pointers
<7> [152.635473] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [152.635637] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1366, min size 1366)
<7> [152.635797] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 305, min size 305)
<7> [152.635957] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 78, min size 78)
<7> [152.636116] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)
<7> [152.636276] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 56 (size 210, min size 210)
<7> [152.636416] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0
<7> [152.636553] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [152.636691] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Expected child device config size for VBT version 251 not known; assuming 39
<7> [152.636833] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [152.637002] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [152.637174] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [152.637340] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [152.637501] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [152.637645] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [152.637796] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [152.637943] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [152.638100] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0
<7> [152.638264] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0
<7> [152.638435] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT HDMI level shift: 0
<7> [152.638593] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0
<7> [152.638767] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0
<7> [152.638904] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 4000000a
<7> [152.639106] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [152.639376] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [152.639563] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [152.639734] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [152.639902] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [152.640115] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [152.640342] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [152.640498] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [152.640764] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [152.640925] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [152.641081] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [152.641298] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [152.641477] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [152.641648] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [152.641821] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [152.641991] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [152.642195] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [152.642409] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_B
<7> [152.642593] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_C
<7> [152.642759] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_D
<7> [152.643018] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/adlp_dmc.bin
<7> [152.644730] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [152.646066] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 35 us
<6> [152.646331] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/adlp_dmc.bin (v2.19)
<7> [152.646448] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 3 (3.0 usec)
<7> [152.646624] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 54 (54.0 usec)
<7> [152.646748] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 83 (83.0 usec)
<7> [152.646855] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 106 (106.0 usec)
<7> [152.646962] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 168 (168.0 usec)
<7> [152.647063] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 168 (168.0 usec)
<7> [152.649529] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 4 display pipes available.
<7> [152.652293] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [152.652508] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 652800 kHz
<7> [152.652654] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] Max dotclock rate: 1305600 kHz
<7> [152.652819] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:235:DDI A/PHY A] using AUX A (VBT)
<7> [152.652976] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:235:DDI A/PHY A]
<7> [152.653157] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [152.653384] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [152.653551] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [152.653708] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [152.653852] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [152.653990] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [152.654160] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [152.654353] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [152.654538] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7> [152.654735] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:235:DDI A/PHY A] initial power sequencer: PPS 0
<7> [152.654975] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [152.655169] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [152.655307] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [152.655476] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [152.655665] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [152.655939] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [152.656166] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [152.656478] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD on
<7> [152.656714] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [152.656967] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [152.657132] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [152.657381] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [152.657584] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [152.895082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [152.923082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [152.952082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [152.981081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.010083] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.039082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.068081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.097082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.126081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.155082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.184082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.213081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.241081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.270092] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.299083] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.328082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.357081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.386081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.415082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.444081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.473081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.502081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.531082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.560081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.589082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.618081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.647082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.676081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.705081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.734081] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.763082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.792082] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [153.792252] i915 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110
<6> [153.792278] i915 0000:00:02.0: [drm] [ENCODER:235:DDI A/PHY A] failed to retrieve link info, disabling eDP
<7> [153.792354] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD off
<7> [153.792578] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [153.792688] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [153.792874] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:235:DDI B/PHY B] using AUX B (VBT)
<7> [153.793005] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:235:DDI B/PHY B]
<7> [153.793424] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:235:DDI B/PHY B]
<7> [153.793540] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:235:DDI B/PHY B] Using DDC pin 0x2 (VBT)
<7> [153.793714] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:254:DDI TC1/PHY TC1] using AUX D (VBT)
<7> [153.793989] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port D/TC#1: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected)
<7> [153.794185] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:254:DDI TC1/PHY TC1]
<7> [153.794410] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:263:DDI TC2/PHY TC2] using AUX E (VBT)
<7> [153.794618] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port E/TC#2: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected)
<7> [153.794850] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:263:DDI TC2/PHY TC2]
<7> [153.795091] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port F is not present
<7> [153.795218] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port G is not present
<7> [153.795453] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:80:pipe A] hw state readout: disabled
<7> [153.795643] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:131:pipe B] hw state readout: disabled
<7> [153.795825] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:182:pipe C] hw state readout: disabled
<7> [153.796117] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:233:pipe D] hw state readout: disabled
<7> [153.796276] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [153.796388] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
<7> [153.796500] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A
<7> [153.796603] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A
<7> [153.796710] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A
<7> [153.796813] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] hw state readout: disabled, pipe A
<7> [153.796911] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] hw state readout: disabled, pipe B
<7> [153.797015] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] hw state readout: disabled, pipe B
<7> [153.797134] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] hw state readout: disabled, pipe B
<7> [153.797235] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] hw state readout: disabled, pipe B
<7> [153.797337] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] hw state readout: disabled, pipe B
<7> [153.797452] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] hw state readout: disabled, pipe B
<7> [153.797557] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] hw state readout: disabled, pipe C
<7> [153.797657] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] hw state readout: disabled, pipe C
<7> [153.797808] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] hw state readout: disabled, pipe C
<7> [153.797962] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] hw state readout: disabled, pipe C
<7> [153.798101] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] hw state readout: disabled, pipe C
<7> [153.798206] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] hw state readout: disabled, pipe C
<7> [153.798326] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:184:plane 1D] hw state readout: disabled, pipe D
<7> [153.798435] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:193:plane 2D] hw state readout: disabled, pipe D
<7> [153.798532] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:202:plane 3D] hw state readout: disabled, pipe D
<7> [153.798628] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:211:plane 4D] hw state readout: disabled, pipe D
<7> [153.798723] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:220:plane 5D] hw state readout: disabled, pipe D
<7> [153.798818] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:229:cursor D] hw state readout: disabled, pipe D
<7> [153.798916] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:235:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [153.799034] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:237:DP-MST A] hw state readout: disabled, pipe A
<7> [153.799201] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DP-MST B] hw state readout: disabled, pipe B
<7> [153.799353] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:239:DP-MST C] hw state readout: disabled, pipe C
<7> [153.799490] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:240:DP-MST D] hw state readout: disabled, pipe D
<7> [153.799627] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port D/TC#1: sanitize mode (disconnected)
<7> [153.799749] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:254:DDI TC1/PHY TC1] hw state readout: disabled, pipe A
<7> [153.799860] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:256:DP-MST A] hw state readout: disabled, pipe A
<7> [153.799961] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:257:DP-MST B] hw state readout: disabled, pipe B
<7> [153.800056] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:258:DP-MST C] hw state readout: disabled, pipe C
<7> [153.800162] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:259:DP-MST D] hw state readout: disabled, pipe D
<7> [153.800273] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port E/TC#2: sanitize mode (disconnected)
<7> [153.800383] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:263:DDI TC2/PHY TC2] hw state readout: disabled, pipe A
<7> [153.800491] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:265:DP-MST A] hw state readout: disabled, pipe A
<7> [153.800585] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:266:DP-MST B] hw state readout: disabled, pipe B
<7> [153.800678] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:267:DP-MST C] hw state readout: disabled, pipe C
<7> [153.800808] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:268:DP-MST D] hw state readout: disabled, pipe D
<7> [153.800962] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [153.801147] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [153.801297] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TBT PLL hw state readout: pipe_mask 0x0, on 0
<7> [153.801427] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [153.801540] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [153.801641] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [153.801746] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [153.801881] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:236:DP-1] hw state readout: disabled
<7> [153.802005] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:249:HDMI-A-1] hw state readout: disabled
<7> [153.802149] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:255:DP-2] hw state readout: disabled
<7> [153.802268] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:264:DP-3] hw state readout: disabled
<7> [153.802379] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [153.802484] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
<7> [153.802607] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz
<7> [153.802757] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz
<7> [153.802900] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz
<7> [153.803008] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] min_cdclk 0 kHz
<7> [153.803143] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [153.803274] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] min_cdclk 0 kHz
<7> [153.803378] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] min_cdclk 0 kHz
<7> [153.803473] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] min_cdclk 0 kHz
<7> [153.803570] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] min_cdclk 0 kHz
<7> [153.803670] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] min_cdclk 0 kHz
<7> [153.803837] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] min_cdclk 0 kHz
<7> [153.803976] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [153.804195] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] min_cdclk 0 kHz
<7> [153.804355] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] min_cdclk 0 kHz
<7> [153.804466] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] min_cdclk 0 kHz
<7> [153.804570] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] min_cdclk 0 kHz
<7> [153.804677] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] min_cdclk 0 kHz
<7> [153.804776] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] min_cdclk 0 kHz
<7> [153.804870] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [153.804993] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:184:plane 1D] min_cdclk 0 kHz
<7> [153.805121] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:193:plane 2D] min_cdclk 0 kHz
<7> [153.805232] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:202:plane 3D] min_cdclk 0 kHz
<7> [153.805332] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:211:plane 4D] min_cdclk 0 kHz
<7> [153.805433] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:220:plane 5D] min_cdclk 0 kHz
<7> [153.805547] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:229:cursor D] min_cdclk 0 kHz
<7> [153.805691] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe D data rate 0 num active planes 0
<7> [153.805912] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: no [setup_hw_state]
<7> [153.806036] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:131:pipe B] enable: no [setup_hw_state]
<7> [153.806160] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:182:pipe C] enable: no [setup_hw_state]
<7> [153.806279] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:233:pipe D] enable: no [setup_hw_state]
<7> [153.806395] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:80:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [153.806513] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:131:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [153.806620] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:182:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [153.806725] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:233:pipe D] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [153.810882] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] GuC WOPCM is already locked [592K, 1420K)
<7> [153.811011] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [153.811149] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000]
<7> [153.811323] MCR Steering: Default steering: group=0x0, instance=0x0
<7> [153.811338] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 GT workarounds on global
<7> [153.812049] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 11 engine workarounds on rcs'0
<7> [153.812185] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0
<7> [153.812296] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 context workarounds on rcs'0
<7> [153.813210] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on bcs'0
<7> [153.813345] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0
<7> [153.813460] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 context workarounds on bcs'0
<7> [153.813839] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'0
<7> [153.813953] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vcs'0
<7> [153.814271] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'2
<7> [153.814377] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vcs'2
<7> [153.814635] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vecs'0
<7> [153.814785] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0
<7> [153.816201] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3)
<7> [153.816369] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 8 KB for temporary ADS regset
<7> [153.833200] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0x16304f
<7> [153.833342] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x44000
<7> [153.833456] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4
<7> [153.833569] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3
<7> [153.833675] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0xac8
<7> [153.833774] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x46aa000c
<7> [153.833871] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0
<7> [153.833964] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0
<7> [153.834056] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0
<7> [153.834169] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0
<7> [153.834331] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0
<7> [153.834476] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0
<7> [153.834581] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0
<7> [153.834689] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0
<7> [153.834791] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no
<6> [153.836294] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/adlp_guc_70.bin version 70.5.1
<6> [153.836297] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/tgl_huc.bin version 7.9.3
<7> [153.855206] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 17ms, freq = 850MHz, before = 850MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [153.855906] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [153.857643] i915 0000:00:02.0: [drm] GT0: HuC: authenticated!
<6> [153.858418] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled
<6> [153.858421] i915 0000:00:02.0: [drm] GT0: GUC: SLPC enabled
<6> [153.859270] i915 0000:00:02.0: [drm] GT0: GUC: RC enabled
<7> [153.865202] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:80:pipe A] not active, skipping
<7> [153.865332] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:131:pipe B] not active, skipping
<7> [153.865442] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:182:pipe C] not active, skipping
<7> [153.865547] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:233:pipe D] not active, skipping
<7> [153.865653] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [153.865765] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [153.866378] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [153.866522] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [153.866612] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [153.866691] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'2 to vcs1
<7> [153.866766] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [153.869491] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [153.870269] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:236:DP-1] generating connector hotplug event
<7> [153.870625] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:249:HDMI-A-1] generating connector hotplug event
<7> [153.870936] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC1/DDI TC1/PHY TC1 bus for card0-DP-2
<7> [153.871636] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:255:DP-2] generating connector hotplug event
<7> [153.871965] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC2/DDI TC2/PHY TC2 bus for card0-DP-3
<7> [153.872626] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:264:DP-3] generating connector hotplug event
<6> [153.872673] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [153.874472] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected
<6> [153.884344] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [153.887349] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input13
<7> [153.888251] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x8010 (init value 0x8010)
<7> [153.888521] i915 0000:00:02.0: [drm:intel_audio_init [i915]] aud_ts_cdclk set to M=60, N=448
<7> [153.889241] [drm:drm_client_modeset_probe]
<7> [153.889291] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [153.889148] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_A
<7> [153.889319] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [153.889823] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_B
<7> [153.890133] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [153.890205] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_C
<7> [153.890355] i915 device info: pciid=0x46aa rev=0x0c platform=ALDERLAKE_P (subplatform=0x0) gen=12
<7> [153.890358] i915 device info: graphics version: 12
<7> [153.890360] i915 device info: media version: 12
<7> [153.890362] i915 device info: display version: 13
<7> [153.890363] i915 device info: graphics stepping: C0
<7> [153.890365] i915 device info: media stepping: C0
<7> [153.890366] i915 device info: display stepping: D0
<7> [153.890368] i915 device info: base die stepping: **
<7> [153.890369] i915 device info: gt: 0
<7> [153.890371] i915 device info: memory-regions: 0x21
<7> [153.890372] i915 device info: page-sizes: 0x211000
<7> [153.890374] i915 device info: platform: ALDERLAKE_P
<7> [153.890375] i915 device info: ppgtt-size: 48
<7> [153.890377] i915 device info: ppgtt-type: 2
<7> [153.890378] i915 device info: dma_mask_size: 39
<7> [153.890379] i915 device info: is_mobile: no
<7> [153.890381] i915 device info: is_lp: no
<7> [153.890382] i915 device info: require_force_probe: no
<7> [153.890384] i915 device info: is_dgfx: no
<7> [153.890385] i915 device info: has_64bit_reloc: yes
<7> [153.890387] i915 device info: has_64k_pages: no
<7> [153.890388] i915 device info: gpu_reset_clobbers_display: no
<7> [153.890389] i915 device info: has_reset_engine: yes
<7> [153.890391] i915 device info: has_3d_pipeline: yes
<7> [153.890392] i915 device info: has_4tile: no
<7> [153.890394] i915 device info: has_flat_ccs: no
<7> [153.890395] i915 device info: has_global_mocs: yes
<7> [153.890396] i915 device info: has_gmd_id: no
<7> [153.890398] i915 device info: has_gt_uc: yes
<7> [153.890399] i915 device info: has_heci_pxp: no
<7> [153.890400] i915 device info: has_heci_gscfi: no
<7> [153.890402] i915 device info: has_guc_deprivilege: no
<7> [153.890413] i915 device info: has_l3_ccs_read: no
<7> [153.890415] i915 device info: has_l3_dpf: no
<7> [153.890416] i915 device info: has_llc: yes
<7> [153.890418] i915 device info: has_logical_ring_contexts: yes
<7> [153.890420] i915 device info: has_logical_ring_elsq: yes
<7> [153.890421] i915 device info: has_media_ratio_mode: no
<7> [153.890423] i915 device info: has_mslice_steering: no
<7> [153.890425] i915 device info: has_oa_bpc_reporting: no
<7> [153.890426] i915 device info: has_oa_slice_contrib_limits: no
<7> [153.890428] i915 device info: has_oam: no
<7> [153.890430] i915 device info: has_one_eu_per_fuse_bit: no
<7> [153.890432] i915 device info: has_pxp: yes
<7> [153.890433] i915 device info: has_rc6: yes
<7> [153.890435] i915 device info: has_rc6p: no
<7> [153.890437] i915 device info: has_rps: yes
<7> [153.890438] i915 device info: has_runtime_pm: yes
<7> [153.890440] i915 device info: has_snoop: no
<7> [153.890441] i915 device info: has_coherent_ggtt: no
<7> [153.890443] i915 device info: tuning_thread_rr_after_dep: no
<7> [153.890445] i915 device info: unfenced_needs_alignment: no
<7> [153.890447] i915 device info: hws_needs_physical: no
<7> [153.890448] i915 device info: has_pooled_eu: no
<7> [153.890450] i915 device info: cursor_needs_physical: no
<7> [153.890452] i915 device info: has_cdclk_crawl: yes
<7> [153.890453] i915 device info: has_cdclk_squash: no
<7> [153.890455] i915 device info: has_ddi: yes
<7> [153.890456] i915 device info: has_dp_mst: yes
<7> [153.890458] i915 device info: has_dsb: yes
<7> [153.890460] i915 device info: has_fpga_dbg: yes
<7> [153.890461] i915 device info: has_gmch: no
<7> [153.890463] i915 device info: has_hotplug: yes
<7> [153.890465] i915 device info: has_hti: no
<7> [153.890466] i915 device info: has_ipc: yes
<7> [153.890468] i915 device info: has_overlay: no
<7> [153.890470] i915 device info: has_psr: yes
<7> [153.890471] i915 device info: has_psr_hw_tracking: no
<7> [153.890473] i915 device info: overlay_needs_physical: no
<7> [153.890475] i915 device info: supports_tv: no
<7> [153.890476] i915 device info: has_hdcp: yes
<7> [153.890478] i915 device info: has_dmc: yes
<7> [153.890480] i915 device info: has_dsc: yes
<7> [153.890481] i915 device info: rawclk rate: 19200 kHz
<7> [153.890483] i915 device info: iommu: enabled
<7> [153.890486] i915 device info: available engines: 41403
<7> [153.890488] i915 device info: slice total: 1, mask=0001
<7> [153.890490] i915 device info: subslice total: 6
<7> [153.890492] i915 device info: slice0: 6 subslices, mask=0000003f
<7> [153.890494] i915 device info: EU total: 96
<7> [153.890496] i915 device info: EU per subslice: 16
<7> [153.890498] i915 device info: has slice power gating: yes
<7> [153.890499] i915 device info: has subslice power gating: no
<7> [153.890501] i915 device info: has EU power gating: no
<6> [153.890503] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [153.890505] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [153.890507] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [153.890434] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_D
<7> [153.890643] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [153.890854] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [153.891067] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [153.891281] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [153.892060] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] status updated from unknown to disconnected
<7> [153.892105] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [153.892196] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [153.892226] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [153.892680] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] status updated from unknown to disconnected
<7> [153.892703] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [153.892726] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [153.892742] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [153.893267] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] status updated from unknown to disconnected
<7> [153.893289] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [153.893307] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [153.893322] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [153.893747] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] status updated from unknown to disconnected
<7> [153.893769] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [153.893787] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [153.893794] [drm:drm_client_modeset_probe] connector 236 enabled? no
<7> [153.893797] [drm:drm_client_modeset_probe] connector 249 enabled? no
<7> [153.893802] [drm:drm_client_modeset_probe] connector 255 enabled? no
<7> [153.893804] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [153.893836] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [153.893847] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [153.893860] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [153.893877] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [153.894308] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [153.894699] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [153.894895] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [153.895238] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [153.895400] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [153.895534] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [153.895717] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [153.895851] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [153.895971] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [153.896630] [drm:drm_client_modeset_probe]
<7> [153.896679] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [153.896703] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [153.897631] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [153.897652] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [153.897674] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [153.897949] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [153.897967] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [153.897983] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [153.898723] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [153.898742] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [153.898758] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [153.899291] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [153.899310] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [153.899315] [drm:drm_client_modeset_probe] connector 236 enabled? no
<7> [153.899319] [drm:drm_client_modeset_probe] connector 249 enabled? no
<7> [153.899323] [drm:drm_client_modeset_probe] connector 255 enabled? no
<7> [153.899326] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [153.899370] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [153.899388] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [153.899406] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [153.899429] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [153.899506] [drm:drm_client_modeset_probe]
<7> [153.899544] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [153.899562] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [153.900198] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [153.900222] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [153.900242] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [153.900701] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [153.901390] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [153.901411] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [153.901430] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [153.901729] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [153.902320] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [153.902515] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [153.902537] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [153.902554] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [153.902714] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [153.903126] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [153.903319] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [153.903336] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [153.903340] [drm:drm_client_modeset_probe] connector 236 enabled? no
<7> [153.903344] [drm:drm_client_modeset_probe] connector 249 enabled? no
<7> [153.903347] [drm:drm_client_modeset_probe] connector 255 enabled? no
<7> [153.903350] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [153.903385] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [153.903397] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [153.903414] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [153.903434] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<6> [153.903449] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100
<6> [153.906876] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [153.907243] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [153.907238] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [153.907467] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [153.907734] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [153.907901] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [153.908505] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [153.908721] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [153.908924] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [153.909135] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [153.909314] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [153.909589] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [153.918421] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [153.920033] [drm:eb_lookup_vmas [i915]] EINVAL at eb_validate_vma:508
<6> [153.928568] [IGT] i915_module_load: finished subtest reload, SUCCESS
<6> [153.928641] [IGT] i915_module_load: exiting, ret=0
Created at 2023-06-18 23:06:04