Results for igt@i915_selftest@live@reset

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g17fbab44f (x86_64) (Linux: 6.4.0-rc6-linus-v6.4-rc6-g858fd168a95c+ x86_64)
Out 
Starting dynamic subtest: reset
Dynamic subtest reset: SUCCESS (5.348s)
Err 
Starting dynamic subtest: reset
Dynamic subtest reset: SUCCESS (5.348s)
Dmesg
<6> [515.364458] [IGT] i915_selftest: starting dynamic subtest reset
<5> [515.516784] Setting dangerous option live_selftests - tainting kernel
<7> [515.591179] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K
<7> [515.591694] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [515.592071] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH
<7> [515.592459] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [515.593039] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [515.593473] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 19200 kHz
<7> [515.594505] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001
<7> [515.594810] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001
<7> [515.595637] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [515.595947] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [515.596249] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M
<6> [515.596592] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [515.596603] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [515.597319] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [515.597355] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7
<7> [515.597700] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K
<7> [515.598487] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018
<7> [515.598926] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0
<7> [515.599271] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [515.599635] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [515.599972] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [515.610316] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583
<7> [515.610712] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [515.611041] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [515.611389] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [515.611740] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [515.612073] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [515.612414] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [515.612708] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [515.612993] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [515.613262] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [515.613541] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [515.613827] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [515.614236] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [515.614582] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [515.614867] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50
<7> [515.615229] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68
<7> [515.615603] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56
<7> [515.615947] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834
<7> [515.616309] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941
<7> [515.616676] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878
<7> [515.617032] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899
<7> [515.617398] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488
<7> [515.617745] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583
<7> [515.618074] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069
<7> [515.618431] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719
<7> [515.618784] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483
<7> [515.619145] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280
<7> [515.619514] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000
<7> [515.619859] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000
<7> [515.620193] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000
<7> [515.620539] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000
<7> [515.620884] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000
<7> [515.621255] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000
<7> [515.621635] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000
<7> [515.621976] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000
<7> [515.622879] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [515.623238] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228
<7> [515.623638] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [515.623995] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5)
<7> [515.624364] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [515.624712] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [515.625049] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812)
<7> [515.625411] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34)
<7> [515.625779] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [515.626149] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)
<7> [515.626521] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [515.626879] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78)
<7> [515.627216] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)
<7> [515.627570] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [515.627922] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [515.628282] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [515.628661] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [515.629014] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [515.629379] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [515.629712] i915 0000:00:02.0: [drm:intel_bios_init [i915]] port C trying to use the same DDC pin (0x3) as port A, disabling port A DVI/HDMI support
<7> [515.630059] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [515.630453] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [515.630807] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000
<7> [515.631140] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [515.631492] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0
<7> [515.631820] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000
<7> [515.632153] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [515.632524] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0
<7> [515.632881] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000
<7> [515.633220] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a
<7> [515.633613] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [515.633991] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [515.634357] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [515.634711] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<6> [515.635110] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [515.635127] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [515.635132] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [515.635137] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [515.635180] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [515.635559] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [515.635910] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [515.636354] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [515.636753] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [515.637102] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [515.637651] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [515.638007] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [515.638372] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [515.638749] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [515.639102] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [515.639490] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [515.639938] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [515.640281] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [515.640645] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [515.640978] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [515.641352] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [515.641838] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [515.642339] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin
<6> [515.644938] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9)
<7> [515.646189] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [515.647158] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us
<7> [515.647534] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [515.647870] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [515.648212] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [515.648590] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [515.648935] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [515.649266] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [515.649612] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [515.649943] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<6> [515.669625] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [515.669646] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [515.669651] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [515.669656] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [515.672000] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 3 display pipes available.
<7> [515.677854] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [515.678485] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz
<7> [515.678878] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] Max dotclock rate: 1113600 kHz
<7> [515.679408] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] using AUX A (VBT)
<7> [515.679789] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A]
<7> [515.684309] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [515.684696] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [515.685050] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [515.685427] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [515.685798] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [515.686134] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [515.686479] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [515.686824] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [515.687180] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [515.687569] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7> [515.688040] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0
<7> [515.688475] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [515.688809] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [515.689146] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [515.689526] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [515.689876] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [515.690329] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [515.690737] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [515.691351] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on
<7> [515.691737] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [515.692160] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [515.692521] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [515.692920] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [515.693274] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [515.903785] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00
<7> [515.904740] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001
<7> [515.905502] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6
<7> [515.906480] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [515.911502] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [515.913323] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [515.915243] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [515.917146] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [515.919089] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [515.921003] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [515.922595] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [515.924529] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [515.925940] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [515.925955] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [515.925963] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [515.926060] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [515.926503] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa
<7> [515.926871] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms)
<7> [515.939957] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none
<7> [515.940503] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0)
<7> [515.940878] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, disabled, brightness 0/96000
<7> [515.941317] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [515.941888] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [515.942234] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [515.942586] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [515.942918] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [515.943359] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [515.944454] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] using AUX B (VBT)
<7> [515.944847] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B]
<7> [515.945588] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [515.945939] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B]
<7> [515.946303] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT)
<7> [515.946888] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:262:DDI C (TC)/PHY C] using AUX C (platform default)
<7> [515.947241] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C]
<7> [515.947579] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT)
<7> [515.948007] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port D is not present
<7> [515.949184] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled
<7> [515.949685] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled
<7> [515.950138] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled
<7> [515.950532] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [515.950900] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
<7> [515.951246] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A
<7> [515.951601] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A
<7> [515.951943] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A
<7> [515.952314] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A
<7> [515.952676] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A
<7> [515.953028] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A
<7> [515.953391] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B
<7> [515.953737] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B
<7> [515.954069] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B
<7> [515.954444] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B
<7> [515.954832] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B
<7> [515.955182] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B
<7> [515.955544] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B
<7> [515.955895] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B
<7> [515.956232] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C
<7> [515.956584] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C
<7> [515.956937] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C
<7> [515.957329] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C
<7> [515.957693] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C
<7> [515.958035] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C
<7> [515.958392] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C
<7> [515.958733] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C
<7> [515.959086] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [515.959474] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [515.959913] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A
<7> [515.960246] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B
<7> [515.960585] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C
<7> [515.960927] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A
<7> [515.961274] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [515.961674] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [515.962040] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [515.962489] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled
<7> [515.962849] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled
<7> [515.963199] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled
<7> [515.963561] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled
<7> [515.963887] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [515.964202] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
<7> [515.964544] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz
<7> [515.964893] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz
<7> [515.965248] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz
<7> [515.965603] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz
<7> [515.965940] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz
<7> [515.966262] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz
<7> [515.966602] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [515.966969] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz
<6> [515.967374] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:00:1c.4
<4> [515.967396] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [515.967401] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000
<4> [515.967407] pcieport 0000:00:1c.4: [ 0] RxErr (First)
<7> [515.967437] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz
<7> [515.967776] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz
<7> [515.968097] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz
<7> [515.968431] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz
<7> [515.968755] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz
<7> [515.969087] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz
<7> [515.969447] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz
<7> [515.969789] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [515.970134] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz
<7> [515.970517] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz
<7> [515.970846] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz
<7> [515.971159] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz
<7> [515.971503] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz
<7> [515.971849] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz
<7> [515.972195] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz
<7> [515.972543] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz
<7> [515.972878] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [515.993979] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state]
<7> [515.994398] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state]
<7> [515.994741] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state]
<7> [515.995079] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [515.995433] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [515.995987] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [515.996756] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [515.997063] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [515.997397] MCR Steering: Default steering: group=0x0, instance=0x0
<7> [515.997423] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global
<7> [515.999869] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0
<7> [516.000254] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0
<7> [516.000617] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0
<7> [516.003195] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0
<7> [516.004588] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0
<7> [516.005563] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0
<7> [516.022092] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping
<7> [516.022595] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping
<7> [516.022940] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping
<7> [516.023267] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [516.023660] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [516.025299] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [516.025631] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [516.025913] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [516.026215] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [516.031914] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered
<7> [516.032502] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [516.033939] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event
<7> [516.035243] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [516.036591] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event
<7> [516.037278] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event
<7> [516.037995] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event
<6> [516.038100] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [516.041854] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected
<6> [516.063574] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [516.063599] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [516.063604] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [516.063611] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [516.073344] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [516.080682] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input49
<7> [516.082071] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x810 (init value 0x810)
<6> [516.082556] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [516.083212] [drm:drm_client_modeset_probe]
<7> [516.083213] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4
<7> [516.083462] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]
<7> [516.083507] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [516.083864] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] status updated from unknown to disconnected
<7> [516.083913] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] disconnected
<7> [516.083947] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:239:eDP-1] EDID changed, epoch counter 2
<7> [516.083977] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]
<7> [516.084010] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [516.084372] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] status updated from unknown to disconnected
<7> [516.084414] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected
<7> [516.084445] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]
<7> [516.084476] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [516.084809] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected
<7> [516.084848] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [516.084879] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]
<7> [516.084911] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [516.085259] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected
<7> [516.085314] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [516.085345] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [516.085353] [drm:drm_client_modeset_probe] connector 239 enabled? no
<7> [516.085360] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [516.085366] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [516.085371] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [516.085439] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [516.085460] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [516.085490] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [516.085528] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [516.085805] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [516.086178] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11
<7> [516.086185] i915 device info: graphics version: 11
<7> [516.086189] i915 device info: media version: 11
<7> [516.086193] i915 device info: display version: 11
<7> [516.086197] i915 device info: graphics stepping: B0
<7> [516.086200] i915 device info: media stepping: B0
<7> [516.086203] i915 device info: display stepping: B0
<7> [516.086207] i915 device info: base die stepping: **
<7> [516.086210] i915 device info: gt: 0
<7> [516.086213] i915 device info: memory-regions: 0x21
<7> [516.086217] i915 device info: page-sizes: 0x211000
<7> [516.086220] i915 device info: platform: JASPERLAKE
<7> [516.086224] i915 device info: ppgtt-size: 36
<7> [516.086227] i915 device info: ppgtt-type: 2
<7> [516.086230] i915 device info: dma_mask_size: 39
<7> [516.086234] i915 device info: is_mobile: no
<7> [516.086237] i915 device info: is_lp: no
<7> [516.086240] i915 device info: require_force_probe: no
<7> [516.086244] i915 device info: is_dgfx: no
<7> [516.086247] i915 device info: has_64bit_reloc: yes
<7> [516.086250] i915 device info: has_64k_pages: no
<7> [516.086254] i915 device info: gpu_reset_clobbers_display: no
<7> [516.086257] i915 device info: has_reset_engine: yes
<7> [516.086261] i915 device info: has_3d_pipeline: yes
<7> [516.086264] i915 device info: has_4tile: no
<7> [516.086267] i915 device info: has_flat_ccs: no
<7> [516.086271] i915 device info: has_global_mocs: no
<7> [516.086274] i915 device info: has_gmd_id: no
<7> [516.086277] i915 device info: has_gt_uc: yes
<7> [516.086280] i915 device info: has_heci_pxp: no
<7> [516.086284] i915 device info: has_heci_gscfi: no
<7> [516.086309] i915 device info: has_guc_deprivilege: no
<7> [516.086313] i915 device info: has_l3_ccs_read: no
<7> [516.086317] i915 device info: has_l3_dpf: no
<7> [516.086320] i915 device info: has_llc: yes
<7> [516.086323] i915 device info: has_logical_ring_contexts: yes
<7> [516.086326] i915 device info: has_logical_ring_elsq: yes
<7> [516.086330] i915 device info: has_media_ratio_mode: no
<7> [516.086333] i915 device info: has_mslice_steering: no
<7> [516.086336] i915 device info: has_oa_bpc_reporting: no
<7> [516.086339] i915 device info: has_oa_slice_contrib_limits: no
<7> [516.086343] i915 device info: has_oam: no
<7> [516.086346] i915 device info: has_one_eu_per_fuse_bit: no
<7> [516.086349] i915 device info: has_pxp: no
<7> [516.086352] i915 device info: has_rc6: yes
<7> [516.086356] i915 device info: has_rc6p: no
<7> [516.086359] i915 device info: has_rps: yes
<7> [516.086362] i915 device info: has_runtime_pm: yes
<7> [516.086365] i915 device info: has_snoop: no
<7> [516.086368] i915 device info: has_coherent_ggtt: no
<7> [516.086371] i915 device info: tuning_thread_rr_after_dep: no
<7> [516.086375] i915 device info: unfenced_needs_alignment: no
<7> [516.086378] i915 device info: hws_needs_physical: no
<7> [516.086381] i915 device info: has_pooled_eu: no
<7> [516.086385] i915 device info: cursor_needs_physical: no
<7> [516.086388] i915 device info: has_cdclk_crawl: no
<7> [516.086392] i915 device info: has_cdclk_squash: no
<7> [516.086395] i915 device info: has_ddi: yes
<7> [516.086398] i915 device info: has_dp_mst: yes
<7> [516.086401] i915 device info: has_dsb: no
<7> [516.086404] i915 device info: has_fpga_dbg: yes
<7> [516.086408] i915 device info: has_gmch: no
<7> [516.086411] i915 device info: has_hotplug: yes
<7> [516.086414] i915 device info: has_hti: no
<7> [516.086417] i915 device info: has_ipc: yes
<7> [516.086421] i915 device info: has_overlay: no
<7> [516.086424] i915 device info: has_psr: yes
<7> [516.086427] i915 device info: has_psr_hw_tracking: yes
<7> [516.086431] i915 device info: overlay_needs_physical: no
<7> [516.086434] i915 device info: supports_tv: no
<7> [516.086437] i915 device info: has_hdcp: no
<7> [516.086441] i915 device info: has_dmc: yes
<7> [516.086444] i915 device info: has_dsc: yes
<7> [516.086447] i915 device info: rawclk rate: 19200 kHz
<7> [516.086451] i915 device info: iommu: enabled
<7> [516.086456] i915 device info: available engines: 40403
<7> [516.086460] i915 device info: slice total: 1, mask=0001
<7> [516.086464] i915 device info: subslice total: 4
<7> [516.086468] i915 device info: slice0: 4 subslices, mask=0000000f
<7> [516.086472] i915 device info: EU total: 16
<7> [516.086475] i915 device info: EU per subslice: 4
<7> [516.086479] i915 device info: has slice power gating: yes
<7> [516.086482] i915 device info: has subslice power gating: yes
<7> [516.086485] i915 device info: has EU power gating: yes
<6> [516.086489] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [516.086493] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [516.086497] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<6> [516.086503] i915: Performing live selftests with st_random_seed=0x3cfbc3f3 st_timeout=500
<6> [516.086507] i915: Running reset
<6> [516.086543] i915: Running intel_reset_live_selftests/igt_global_reset
<6> [516.090188] i915: Running intel_reset_live_selftests/igt_reset_device_stolen
<7> [516.114905] [drm:drm_client_modeset_probe]
<7> [516.114982] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]
<7> [516.115028] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [516.115478] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] disconnected
<7> [516.115519] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]
<7> [516.115552] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [516.115944] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected
<7> [516.115979] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]
<7> [516.116012] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [516.117226] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [516.117261] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]
<7> [516.117309] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [516.117648] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [516.117678] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [516.117688] [drm:drm_client_modeset_probe] connector 239 enabled? no
<7> [516.117694] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [516.117699] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [516.117705] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [516.117768] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [516.117788] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [516.117820] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [516.117858] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [516.158412] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [516.159333] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<6> [516.926548] i915: Running intel_reset_live_selftests/igt_reset_engines_stolen
<7> [518.991387] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD off
<7> [518.992027] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [518.992413] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [518.993030] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [518.993472] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [518.993843] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [518.995093] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [518.995372] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long
<7> [518.995740] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [518.996246] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]
<6> [519.037011] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [519.037033] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [519.037039] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [519.037044] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [519.038340] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:00:1c.4
<4> [519.038362] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [519.038367] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000
<4> [519.038372] pcieport 0000:00:1c.4: [ 0] RxErr (First)
<7> [519.062432] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [519.366318] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [519.878396] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [519.884039] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [519.884062] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [519.884067] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [519.884073] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [519.921159] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [519.921178] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [519.921183] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [519.921189] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [519.970622] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [519.970641] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [519.970646] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [519.970651] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [520.189698] i915: Running intel_reset_live_selftests/igt_wedged_reset
<7> [520.189743] intel_gt_set_wedged called from igt_wedged_reset+0x25/0x180 [i915]
<6> [520.204278] i915: Running intel_reset_live_selftests/igt_atomic_reset
<7> [520.204556] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [520.205175] intel_gt_set_wedged called from igt_force_reset+0xd/0xe0 [i915]
<7> [520.223485] intel_gt_set_wedged called from igt_force_reset+0xd/0xe0 [i915]
<6> [520.233125] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [520.233147] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [520.233152] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [520.233158] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [520.237387] i915: Running intel_reset_live_selftests/igt_atomic_engine_reset
<7> [520.237618] intel_gt_set_wedged called from igt_force_reset+0xd/0xe0 [i915]
<7> [520.282358] intel_gt_set_wedged called from igt_force_reset+0xd/0xe0 [i915]
<6> [520.293406] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [520.293428] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [520.293433] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [520.293439] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [520.295529] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [520.296310] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [520.297183] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [520.297593] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [520.297948] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [520.298312] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [520.298668] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [520.299041] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [520.299413] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [520.299776] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [520.300133] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<6> [520.311265] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [520.311317] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [520.311324] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [520.311329] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [520.332813] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [520.373129] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [520.373670] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [520.374221] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [520.374621] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<4> [520.416043] i915: probe of 0000:00:02.0 failed with error -25
<6> [520.418525] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [520.418547] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [520.418553] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [520.418559] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [520.419391] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [520.419406] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [520.419410] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [520.419415] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [520.514690] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [520.514714] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [520.514719] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [520.514725] nvme 0000:02:00.0: [ 0] RxErr (First)
Created at 2023-06-12 09:40:49