Results for igt@i915_module_load@reload

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g17fbab44f (x86_64) (Linux: 6.4.0-rc6-linus-v6.4-rc6-g858fd168a95c+ x86_64)
Out 
Starting subtest: reload
Opened device: /dev/dri/card0
Subtest reload: SUCCESS (2.819s)
Err 
Starting subtest: reload
Subtest reload: SUCCESS (2.819s)
Dmesg
<6> [133.385855] [IGT] i915_module_load: executing
<6> [133.388558] [IGT] i915_module_load: starting subtest reload
<7> [133.438184] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [133.438353] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [133.438519] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [133.438702] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [133.439067] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [133.439716] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [133.439900] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [133.440319] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [133.442110] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [133.442245] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [133.445964] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [133.447030] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [133.447327] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [133.447514] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [133.447615] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [133.447878] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [133.448021] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [133.448164] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [133.448295] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [133.448401] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [133.448528] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [133.448803] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [133.448742] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [133.448821] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [133.448972] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 1
<7> [133.448988] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [133.449156] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [133.449170] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [133.449318] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [133.462055] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [133.462222] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [133.462428] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [133.462538] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [133.462950] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [133.491575] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [133.491914] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [133.492395] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [133.492960] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [133.493260] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [133.493518] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [133.493767] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [133.494001] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [133.494260] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [133.506994] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [133.507216] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [133.507406] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [133.507586] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [133.508082] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [133.577506] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [133.577722] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [133.578046] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [133.578260] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [133.578484] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [133.578667] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [133.578805] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [133.578923] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [133.579060] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [133.597185] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port A
<7> [133.597389] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port A
<7> [133.597551] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port A
<7> [133.597703] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port A
<7> [133.597856] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [133.598007] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [133.598165] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [133.598407] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [133.598589] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [133.598725] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [133.598852] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [133.598977] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [133.599101] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [133.599256] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [133.599375] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [133.599517] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [133.599683] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port E
<7> [133.599819] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port E
<7> [133.599927] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port E
<7> [133.600032] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port E
<7> [133.600156] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port F
<7> [133.600270] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port F
<7> [133.600376] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port F
<7> [133.600480] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port F
<7> [133.600617] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port G
<7> [133.600781] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port G
<7> [133.600901] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port G
<7> [133.601009] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port G
<7> [133.601116] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port H
<7> [133.601243] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port H
<7> [133.601346] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port H
<7> [133.601449] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port H
<7> [133.601552] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port I
<7> [133.601697] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port I
<7> [133.601846] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port I
<7> [133.601988] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port I
<7> [133.602402] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [133.602520] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [133.602635] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [133.602741] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [133.603197] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [133.765870] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind
<7> [133.832837] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [133.833727] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [133.834755] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [133.835802] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [133.836542] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [133.837094] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [133.837684] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [133.838172] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [133.838743] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [133.839211] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_B
<7> [133.839618] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_C
<7> [133.839973] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_D
<7> [133.869298] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [133.933877] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [134.883365] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K
<7> [134.883565] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:yes huc:yes slpc:yes)
<7> [134.883700] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Alder Lake PCH
<7> [134.883818] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [134.884223] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 19200 kHz
<7> [134.884588] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0005, instances: 0005
<7> [134.884681] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001
<7> [134.884993] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [134.885083] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [134.885176] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M
<6> [134.885260] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [134.885264] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [134.885524] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [134.885537] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x0000000050200087
<7> [134.885663] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K
<7> [134.885900] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x44a07018
<7> [134.886039] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0
<7> [134.886171] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [134.886281] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [134.886378] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [134.886484] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (RVDA)
<7> [134.886599] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 4
<7> [134.886691] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [134.886778] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2401 tRP=24 tRDPRE=20 tRAS=52 tRCD=24 tRC=76
<7> [134.886911] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=4801 tRP=44 tRDPRE=28 tRAS=104 tRCD=44 tRC=148
<7> [134.887036] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=5201 tRP=48 tRDPRE=28 tRAS=112 tRCD=48 tRC=160
<7> [134.887168] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 3: DCLK=5201 tRP=48 tRDPRE=28 tRAS=112 tRCD=48 tRC=160
<7> [134.887279] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 0: CLK=32
<7> [134.887384] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 1: CLK=39
<7> [134.887487] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 2: CLK=48
<7> [134.887591] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 0: num_planes=0 deratedbw=16956
<7> [134.887700] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 1: num_planes=0 deratedbw=23981
<7> [134.887804] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 2: num_planes=0 deratedbw=24772
<7> [134.887911] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 3: num_planes=0 deratedbw=24772
<7> [134.888021] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 0: num_planes=0 bw=34133
<7> [134.888130] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 1: num_planes=0 bw=41600
<7> [134.888232] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 2: num_planes=0 bw=51200
<7> [134.888331] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 0: num_planes=4 deratedbw=21855
<7> [134.888429] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 1: num_planes=4 deratedbw=34500
<7> [134.888526] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 2: num_planes=4 deratedbw=36108
<7> [134.888623] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 3: num_planes=4 deratedbw=36108
<7> [134.888729] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 0: num_planes=4 bw=34133
<7> [134.888835] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 1: num_planes=4 bw=41600
<7> [134.888943] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 2: num_planes=4 bw=51200
<7> [134.889046] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 0: num_planes=0 deratedbw=25544
<7> [134.889151] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 1: num_planes=0 deratedbw=38000
<7> [134.889249] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 2: num_planes=0 deratedbw=38000
<7> [134.889347] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 3: num_planes=0 deratedbw=38000
<7> [134.889451] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 0: num_planes=0 bw=34133
<7> [134.889551] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 1: num_planes=0 bw=41600
<7> [134.889649] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 2: num_planes=0 bw=51200
<7> [134.889747] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 0: num_planes=0 deratedbw=27900
<7> [134.889855] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 1: num_planes=0 deratedbw=38000
<7> [134.889957] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 2: num_planes=0 deratedbw=38000
<7> [134.890056] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 3: num_planes=0 deratedbw=38000
<7> [134.890165] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 0: num_planes=0 bw=34133
<7> [134.890272] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 1: num_planes=0 bw=41600
<7> [134.890380] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 2: num_planes=0 bw=51200
<7> [134.890483] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 0: num_planes=0 deratedbw=29248
<7> [134.890583] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 1: num_planes=0 deratedbw=38000
<7> [134.890682] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 2: num_planes=0 deratedbw=38000
<7> [134.890777] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 3: num_planes=0 deratedbw=38000
<7> [134.890874] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 0: num_planes=0 bw=34133
<7> [134.890979] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 1: num_planes=0 bw=41600
<7> [134.891080] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 2: num_planes=0 bw=51200
<7> [134.891187] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 0: num_planes=0 deratedbw=29972
<7> [134.891284] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 1: num_planes=0 deratedbw=38000
<7> [134.891385] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 2: num_planes=0 deratedbw=38000
<7> [134.891491] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 3: num_planes=0 deratedbw=38000
<7> [134.891592] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 0: num_planes=0 bw=34133
<7> [134.891691] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 1: num_planes=0 bw=41600
<7> [134.891787] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 2: num_planes=0 bw=51200
<7> [134.892860] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [134.893062] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT ALDERLAKE-P ", BDB version 251
<7> [134.893261] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 10, min size 7)
<7> [134.893445] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 395, min size 5)
<7> [134.893625] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 100, min size 100)
<7> [134.893800] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [134.893979] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 814, min size 812)
<7> [134.894139] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 34, min size 34)
<7> [134.894295] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Generating LFP data table pointers
<7> [134.894453] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [134.894603] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1366, min size 1366)
<7> [134.894747] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 305, min size 305)
<7> [134.894891] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 78, min size 78)
<7> [134.895033] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)
<7> [134.895180] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 56 (size 210, min size 210)
<7> [134.895329] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0
<7> [134.895474] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [134.895610] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Expected child device config size for VBT version 251 not known; assuming 39
<7> [134.895745] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [134.895882] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [134.896033] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [134.896189] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [134.896352] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [134.896510] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [134.896678] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [134.896824] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [134.896958] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0
<7> [134.897095] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0
<7> [134.897261] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT HDMI level shift: 0
<7> [134.897419] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0
<7> [134.897572] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0
<7> [134.897724] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 4000000a
<7> [134.897904] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [134.898159] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [134.898320] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [134.898475] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [134.898628] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [134.898794] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [134.898967] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [134.899116] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [134.899366] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [134.899513] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [134.899659] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [134.899835] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [134.899995] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [134.900159] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [134.900315] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [134.900455] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [134.900614] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [134.900780] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_B
<7> [134.900927] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_C
<7> [134.901072] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_D
<7> [134.901310] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/adlp_dmc.bin
<7> [134.902774] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<6> [134.904232] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/adlp_dmc.bin (v2.19)
<7> [134.904197] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 35 us
<7> [134.904385] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 3 (3.0 usec)
<7> [134.904535] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 54 (54.0 usec)
<7> [134.904678] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 83 (83.0 usec)
<7> [134.904819] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 106 (106.0 usec)
<7> [134.904957] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 168 (168.0 usec)
<7> [134.905095] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 168 (168.0 usec)
<7> [134.907701] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 4 display pipes available.
<7> [134.911009] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [134.911259] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 652800 kHz
<7> [134.911414] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] Max dotclock rate: 1305600 kHz
<7> [134.911577] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:235:DDI A/PHY A] using AUX A (VBT)
<7> [134.911727] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:235:DDI A/PHY A]
<7> [134.911864] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [134.912008] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [134.912153] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [134.912329] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [134.912451] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [134.912637] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [134.912771] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [134.912896] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [134.913014] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7> [134.913221] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:235:DDI A/PHY A] initial power sequencer: PPS 0
<7> [134.913447] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [134.913609] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [134.913714] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [134.913816] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [134.913919] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [134.914187] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [134.914362] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [134.914650] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD on
<7> [134.914803] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [134.915037] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [134.915188] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [134.915410] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [134.915541] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [135.149131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.178130] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.207132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.236131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.265130] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.294131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.323132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.352131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.381132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.410131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.439131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.468132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.497131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.526131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.555131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.584132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.613131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.642131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.671132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.700132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.729131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.758132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.787131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.816132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.845131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.874131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.903131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.932131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.961132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [135.990134] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [136.019131] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [136.048132] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [136.048343] i915 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110
<6> [136.048380] i915 0000:00:02.0: [drm] [ENCODER:235:DDI A/PHY A] failed to retrieve link info, disabling eDP
<7> [136.048465] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD off
<7> [136.048738] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [136.048907] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [136.049179] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:235:DDI B/PHY B] using AUX B (VBT)
<7> [136.049343] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:235:DDI B/PHY B]
<7> [136.049781] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:235:DDI B/PHY B]
<7> [136.049930] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:235:DDI B/PHY B] Using DDC pin 0x2 (VBT)
<7> [136.050182] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:254:DDI TC1/PHY TC1] using AUX D (VBT)
<7> [136.050550] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port D/TC#1: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected)
<7> [136.050776] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:254:DDI TC1/PHY TC1]
<7> [136.051087] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:263:DDI TC2/PHY TC2] using AUX E (VBT)
<7> [136.051354] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port E/TC#2: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected)
<7> [136.051564] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:263:DDI TC2/PHY TC2]
<7> [136.051834] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port F is not present
<7> [136.051994] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port G is not present
<7> [136.052326] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:80:pipe A] hw state readout: disabled
<7> [136.052586] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:131:pipe B] hw state readout: disabled
<7> [136.052825] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:182:pipe C] hw state readout: disabled
<7> [136.053063] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:233:pipe D] hw state readout: disabled
<7> [136.053225] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [136.053379] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
<7> [136.053530] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A
<7> [136.053677] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A
<7> [136.053824] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A
<7> [136.053970] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] hw state readout: disabled, pipe A
<7> [136.054116] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] hw state readout: disabled, pipe B
<7> [136.054270] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] hw state readout: disabled, pipe B
<7> [136.054415] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] hw state readout: disabled, pipe B
<7> [136.054563] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] hw state readout: disabled, pipe B
<7> [136.054708] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] hw state readout: disabled, pipe B
<7> [136.054852] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] hw state readout: disabled, pipe B
<7> [136.055008] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] hw state readout: disabled, pipe C
<7> [136.055159] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] hw state readout: disabled, pipe C
<7> [136.055303] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] hw state readout: disabled, pipe C
<7> [136.055454] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] hw state readout: disabled, pipe C
<7> [136.055598] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] hw state readout: disabled, pipe C
<7> [136.055741] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] hw state readout: disabled, pipe C
<7> [136.055884] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:184:plane 1D] hw state readout: disabled, pipe D
<7> [136.056027] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:193:plane 2D] hw state readout: disabled, pipe D
<7> [136.056178] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:202:plane 3D] hw state readout: disabled, pipe D
<7> [136.056321] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:211:plane 4D] hw state readout: disabled, pipe D
<7> [136.056469] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:220:plane 5D] hw state readout: disabled, pipe D
<7> [136.056615] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:229:cursor D] hw state readout: disabled, pipe D
<7> [136.056760] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:235:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [136.056896] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:237:DP-MST A] hw state readout: disabled, pipe A
<7> [136.057032] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DP-MST B] hw state readout: disabled, pipe B
<7> [136.057177] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:239:DP-MST C] hw state readout: disabled, pipe C
<7> [136.057321] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:240:DP-MST D] hw state readout: disabled, pipe D
<7> [136.057502] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port D/TC#1: sanitize mode (disconnected)
<7> [136.057647] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:254:DDI TC1/PHY TC1] hw state readout: disabled, pipe A
<7> [136.057785] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:256:DP-MST A] hw state readout: disabled, pipe A
<7> [136.057921] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:257:DP-MST B] hw state readout: disabled, pipe B
<7> [136.058056] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:258:DP-MST C] hw state readout: disabled, pipe C
<7> [136.058198] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:259:DP-MST D] hw state readout: disabled, pipe D
<7> [136.058346] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port E/TC#2: sanitize mode (disconnected)
<7> [136.058493] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:263:DDI TC2/PHY TC2] hw state readout: disabled, pipe A
<7> [136.058656] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:265:DP-MST A] hw state readout: disabled, pipe A
<7> [136.058793] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:266:DP-MST B] hw state readout: disabled, pipe B
<7> [136.058934] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:267:DP-MST C] hw state readout: disabled, pipe C
<7> [136.059076] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:268:DP-MST D] hw state readout: disabled, pipe D
<7> [136.059238] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [136.059398] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [136.059549] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TBT PLL hw state readout: pipe_mask 0x0, on 0
<7> [136.059700] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [136.059848] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [136.059995] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [136.060152] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [136.060343] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:236:DP-1] hw state readout: disabled
<7> [136.060513] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:249:HDMI-A-1] hw state readout: disabled
<7> [136.060684] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:255:DP-2] hw state readout: disabled
<7> [136.060853] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:264:DP-3] hw state readout: disabled
<7> [136.061003] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [136.061146] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
<7> [136.061280] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz
<7> [136.061416] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz
<7> [136.061554] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz
<7> [136.061686] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] min_cdclk 0 kHz
<7> [136.061834] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [136.061991] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] min_cdclk 0 kHz
<7> [136.062155] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] min_cdclk 0 kHz
<7> [136.062314] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] min_cdclk 0 kHz
<7> [136.062449] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] min_cdclk 0 kHz
<7> [136.062580] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] min_cdclk 0 kHz
<7> [136.062712] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] min_cdclk 0 kHz
<7> [136.062843] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [136.062999] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] min_cdclk 0 kHz
<7> [136.063142] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] min_cdclk 0 kHz
<7> [136.063277] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] min_cdclk 0 kHz
<7> [136.063410] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] min_cdclk 0 kHz
<7> [136.063540] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] min_cdclk 0 kHz
<7> [136.063671] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] min_cdclk 0 kHz
<7> [136.063801] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [136.063956] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:184:plane 1D] min_cdclk 0 kHz
<7> [136.064091] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:193:plane 2D] min_cdclk 0 kHz
<7> [136.064230] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:202:plane 3D] min_cdclk 0 kHz
<7> [136.064362] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:211:plane 4D] min_cdclk 0 kHz
<7> [136.064494] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:220:plane 5D] min_cdclk 0 kHz
<7> [136.064625] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:229:cursor D] min_cdclk 0 kHz
<7> [136.064755] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe D data rate 0 num active planes 0
<7> [136.064968] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: no [setup_hw_state]
<7> [136.065130] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:131:pipe B] enable: no [setup_hw_state]
<7> [136.065282] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:182:pipe C] enable: no [setup_hw_state]
<7> [136.065433] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:233:pipe D] enable: no [setup_hw_state]
<7> [136.065588] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:80:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [136.065733] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:131:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [136.065874] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:182:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [136.066012] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:233:pipe D] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [136.071385] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] GuC WOPCM is already locked [592K, 1420K)
<7> [136.071565] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [136.071701] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000]
<7> [136.071839] MCR Steering: Default steering: group=0x0, instance=0x0
<7> [136.071852] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 GT workarounds on global
<7> [136.072935] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 11 engine workarounds on rcs'0
<7> [136.073093] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0
<7> [136.073255] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 context workarounds on rcs'0
<7> [136.074177] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on bcs'0
<7> [136.074332] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0
<7> [136.074479] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 context workarounds on bcs'0
<7> [136.075248] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'0
<7> [136.075396] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vcs'0
<7> [136.075907] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'2
<7> [136.076052] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vcs'2
<7> [136.076434] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vecs'0
<7> [136.076580] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0
<7> [136.078271] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3)
<7> [136.078496] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 8 KB for temporary ADS regset
<7> [136.100190] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0x16304f
<7> [136.100442] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x44000
<7> [136.100602] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4
<7> [136.100758] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3
<7> [136.100914] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0xac8
<7> [136.101068] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x46aa000c
<7> [136.101236] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0
<7> [136.101391] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0
<7> [136.101545] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0
<7> [136.101696] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0
<7> [136.101847] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0
<7> [136.102040] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0
<7> [136.102270] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0
<7> [136.102398] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0
<7> [136.102528] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no
<6> [136.103593] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/adlp_guc_70.bin version 70.5.1
<6> [136.103596] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/tgl_huc.bin version 7.9.3
<7> [136.124249] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 18ms, freq = 850MHz, before = 850MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [136.124903] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [136.126091] i915 0000:00:02.0: [drm] GT0: HuC: authenticated!
<6> [136.127443] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled
<6> [136.127445] i915 0000:00:02.0: [drm] GT0: GUC: SLPC enabled
<6> [136.128283] i915 0000:00:02.0: [drm] GT0: GUC: RC enabled
<7> [136.134723] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:80:pipe A] not active, skipping
<7> [136.134863] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:131:pipe B] not active, skipping
<7> [136.134980] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:182:pipe C] not active, skipping
<7> [136.135094] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:233:pipe D] not active, skipping
<7> [136.135214] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [136.135329] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [136.135947] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [136.136050] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [136.136144] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [136.136225] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'2 to vcs1
<7> [136.136301] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [136.138529] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [136.139229] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:236:DP-1] generating connector hotplug event
<7> [136.139485] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:249:HDMI-A-1] generating connector hotplug event
<7> [136.139684] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC1/DDI TC1/PHY TC1 bus for card0-DP-2
<7> [136.140079] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:255:DP-2] generating connector hotplug event
<7> [136.140454] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC2/DDI TC2/PHY TC2 bus for card0-DP-3
<7> [136.140836] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:264:DP-3] generating connector hotplug event
<6> [136.140864] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [136.142056] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected
<6> [136.149355] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [136.151421] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input13
<7> [136.152107] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x8010 (init value 0x8010)
<7> [136.152276] i915 0000:00:02.0: [drm:intel_audio_init [i915]] aud_ts_cdclk set to M=60, N=448
<7> [136.152648] [drm:drm_client_modeset_probe]
<7> [136.152695] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [136.152646] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_A
<7> [136.152723] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [136.153216] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [136.153200] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_B
<7> [136.153359] i915 device info: pciid=0x46aa rev=0x0c platform=ALDERLAKE_P (subplatform=0x0) gen=12
<7> [136.153361] i915 device info: graphics version: 12
<7> [136.153362] i915 device info: media version: 12
<7> [136.153363] i915 device info: display version: 13
<7> [136.153364] i915 device info: graphics stepping: C0
<7> [136.153365] i915 device info: media stepping: C0
<7> [136.153366] i915 device info: display stepping: D0
<7> [136.153367] i915 device info: base die stepping: **
<7> [136.153368] i915 device info: gt: 0
<7> [136.153369] i915 device info: memory-regions: 0x21
<7> [136.153370] i915 device info: page-sizes: 0x211000
<7> [136.153371] i915 device info: platform: ALDERLAKE_P
<7> [136.153372] i915 device info: ppgtt-size: 48
<7> [136.153373] i915 device info: ppgtt-type: 2
<7> [136.153374] i915 device info: dma_mask_size: 39
<7> [136.153374] i915 device info: is_mobile: no
<7> [136.153375] i915 device info: is_lp: no
<7> [136.153376] i915 device info: require_force_probe: no
<7> [136.153377] i915 device info: is_dgfx: no
<7> [136.153378] i915 device info: has_64bit_reloc: yes
<7> [136.153379] i915 device info: has_64k_pages: no
<7> [136.153380] i915 device info: gpu_reset_clobbers_display: no
<7> [136.153381] i915 device info: has_reset_engine: yes
<7> [136.153382] i915 device info: has_3d_pipeline: yes
<7> [136.153383] i915 device info: has_4tile: no
<7> [136.153383] i915 device info: has_flat_ccs: no
<7> [136.153384] i915 device info: has_global_mocs: yes
<7> [136.153385] i915 device info: has_gmd_id: no
<7> [136.153386] i915 device info: has_gt_uc: yes
<7> [136.153387] i915 device info: has_heci_pxp: no
<7> [136.153388] i915 device info: has_heci_gscfi: no
<7> [136.153389] i915 device info: has_guc_deprivilege: no
<7> [136.153389] i915 device info: has_l3_ccs_read: no
<7> [136.153390] i915 device info: has_l3_dpf: no
<7> [136.153391] i915 device info: has_llc: yes
<7> [136.153392] i915 device info: has_logical_ring_contexts: yes
<7> [136.153393] i915 device info: has_logical_ring_elsq: yes
<7> [136.153394] i915 device info: has_media_ratio_mode: no
<7> [136.153395] i915 device info: has_mslice_steering: no
<7> [136.153396] i915 device info: has_oa_bpc_reporting: no
<7> [136.153396] i915 device info: has_oa_slice_contrib_limits: no
<7> [136.153397] i915 device info: has_oam: no
<7> [136.153398] i915 device info: has_one_eu_per_fuse_bit: no
<7> [136.153399] i915 device info: has_pxp: yes
<7> [136.153400] i915 device info: has_rc6: yes
<7> [136.153401] i915 device info: has_rc6p: no
<7> [136.153402] i915 device info: has_rps: yes
<7> [136.153402] i915 device info: has_runtime_pm: yes
<7> [136.153403] i915 device info: has_snoop: no
<7> [136.153404] i915 device info: has_coherent_ggtt: no
<7> [136.153405] i915 device info: tuning_thread_rr_after_dep: no
<7> [136.153406] i915 device info: unfenced_needs_alignment: no
<7> [136.153407] i915 device info: hws_needs_physical: no
<7> [136.153418] i915 device info: has_pooled_eu: no
<7> [136.153420] i915 device info: cursor_needs_physical: no
<7> [136.153421] i915 device info: has_cdclk_crawl: yes
<7> [136.153422] i915 device info: has_cdclk_squash: no
<7> [136.153423] i915 device info: has_ddi: yes
<7> [136.153424] i915 device info: has_dp_mst: yes
<7> [136.153425] i915 device info: has_dsb: yes
<7> [136.153426] i915 device info: has_fpga_dbg: yes
<7> [136.153427] i915 device info: has_gmch: no
<7> [136.153428] i915 device info: has_hotplug: yes
<7> [136.153429] i915 device info: has_hti: no
<7> [136.153430] i915 device info: has_ipc: yes
<7> [136.153432] i915 device info: has_overlay: no
<7> [136.153433] i915 device info: has_psr: yes
<7> [136.153434] i915 device info: has_psr_hw_tracking: no
<7> [136.153435] i915 device info: overlay_needs_physical: no
<7> [136.153436] i915 device info: supports_tv: no
<7> [136.153437] i915 device info: has_hdcp: yes
<7> [136.153438] i915 device info: has_dmc: yes
<7> [136.153439] i915 device info: has_dsc: yes
<7> [136.153440] i915 device info: rawclk rate: 19200 kHz
<7> [136.153442] i915 device info: iommu: enabled
<7> [136.153443] i915 device info: available engines: 41403
<7> [136.153444] i915 device info: slice total: 1, mask=0001
<7> [136.153446] i915 device info: subslice total: 6
<7> [136.153447] i915 device info: slice0: 6 subslices, mask=0000003f
<7> [136.153449] i915 device info: EU total: 96
<7> [136.153450] i915 device info: EU per subslice: 16
<7> [136.153451] i915 device info: has slice power gating: yes
<7> [136.153452] i915 device info: has subslice power gating: no
<7> [136.153453] i915 device info: has EU power gating: no
<6> [136.153454] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [136.153456] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [136.153457] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [136.153547] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_C
<7> [136.153771] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_D
<7> [136.154002] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [136.154553] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [136.154746] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [136.154921] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [136.155636] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] status updated from unknown to disconnected
<7> [136.155670] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [136.155686] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [136.155701] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [136.156142] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] status updated from unknown to disconnected
<7> [136.156164] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [136.156179] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [136.156194] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [136.156652] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] status updated from unknown to disconnected
<7> [136.156669] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [136.156681] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [136.156694] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [136.157187] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] status updated from unknown to disconnected
<7> [136.157213] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [136.157225] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [136.157242] [drm:drm_client_modeset_probe] connector 236 enabled? no
<7> [136.157244] [drm:drm_client_modeset_probe] connector 249 enabled? no
<7> [136.157246] [drm:drm_client_modeset_probe] connector 255 enabled? no
<7> [136.157248] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [136.157273] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [136.157280] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [136.157291] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [136.157309] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [136.157572] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [136.157900] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [136.158036] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [136.158170] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [136.158299] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [136.158422] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [136.158592] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [136.158720] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [136.158835] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [136.159650] [drm:drm_client_modeset_probe]
<7> [136.159701] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [136.159724] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [136.160431] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [136.160452] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [136.160469] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [136.160866] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [136.160883] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [136.160900] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [136.161397] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [136.161412] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [136.161426] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [136.161904] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [136.161918] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [136.161922] [drm:drm_client_modeset_probe] connector 236 enabled? no
<7> [136.161925] [drm:drm_client_modeset_probe] connector 249 enabled? no
<7> [136.161928] [drm:drm_client_modeset_probe] connector 255 enabled? no
<7> [136.161931] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [136.161962] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [136.161973] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [136.161989] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [136.162006] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [136.162067] [drm:drm_client_modeset_probe]
<7> [136.162097] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [136.162114] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [136.162514] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [136.162531] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [136.162548] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [136.163029] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [136.163045] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [136.163060] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [136.163557] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [136.163575] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [136.163591] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [136.164076] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [136.164095] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [136.164099] [drm:drm_client_modeset_probe] connector 236 enabled? no
<7> [136.164102] [drm:drm_client_modeset_probe] connector 249 enabled? no
<7> [136.164105] [drm:drm_client_modeset_probe] connector 255 enabled? no
<7> [136.164107] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [136.164151] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [136.164165] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [136.164181] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [136.164202] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<6> [136.165343] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100
<7> [136.168563] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [136.169783] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<6> [136.171205] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [136.171449] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [136.171945] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [136.172198] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [136.172395] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [136.172582] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [136.172763] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [136.172923] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [136.173225] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [136.197693] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [136.199758] [drm:eb_lookup_vmas [i915]] EINVAL at eb_validate_vma:508
<6> [136.207541] [IGT] i915_module_load: exiting, ret=0
Created at 2023-06-12 09:40:48