Results for igt@i915_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gc2d8ef8b9 (x86_64) (Linux: 6.4.0-rc5-linus-v6.4-rc5-g9561de3a55be+ x86_64)
Out	Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x95/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1ec/0x740 drm_ioctl_kernel+0xb6/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x79/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa2d/0xd10 [i915] intel_atomic_commit+0x380/0x400 [i915] drm_atomic_commit+0x95/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1ec/0x740 Wakeref count: 0 Subtest basic-rte: SUCCESS (11.898s) i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x95/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1ec/0x740 drm_ioctl_kernel+0xb6/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x79/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa2d/0xd10 [i915] intel_atomic_commit+0x380/0x400 [i915] drm_atomic_commit+0x95/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1ec/0x740 Wakeref count: 0
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (11.898s)
Dmesg	<6> [121.514333] Console: switching to colour dummy device 80x25 <6> [121.514383] [IGT] i915_pm_rpm: executing <6> [121.523849] [IGT] i915_pm_rpm: starting subtest basic-rte <7> [121.523920] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [121.524366] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [121.524385] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [121.524546] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [121.525041] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [121.525263] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [121.525332] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2] <7> [121.525344] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [121.525479] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [121.525964] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [121.526471] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [121.527067] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [121.528199] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [121.529272] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [121.530028] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [121.530218] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [121.530400] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [121.530546] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [121.531166] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [121.531344] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2] disconnected <7> [121.531408] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] <7> [121.531419] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [121.531556] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [121.532664] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [121.532800] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [121.533337] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [121.533843] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [121.533849] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [121.534068] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [121.558693] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [121.558698] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [121.558848] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [121.559101] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected <7> [121.562730] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [121.562758] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [121.562909] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [121.563382] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [121.563528] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [121.564025] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2] <7> [121.564039] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [121.564174] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [121.564651] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [121.565184] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [121.565740] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [121.566779] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [121.567777] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [121.568520] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [121.568684] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [121.568937] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [121.569092] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [121.569714] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [121.569932] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2] disconnected <7> [121.570379] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] <7> [121.570392] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [121.570526] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [121.571271] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [121.571397] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [121.572134] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [121.572623] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [121.572626] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [121.572761] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [121.597941] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [121.597947] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [121.598087] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [121.598232] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected <7> [121.598536] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [121.598548] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [121.598681] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [121.599234] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [121.599456] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [121.599482] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2] <7> [121.599493] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [121.599636] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [121.600157] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [121.600648] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [121.601236] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [121.602383] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [121.603503] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [121.604270] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [121.604434] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [121.604583] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [121.604727] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [121.605367] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [121.605530] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2] disconnected <7> [121.605556] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] <7> [121.605567] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [121.605703] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [121.606802] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [121.606983] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [121.607731] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [121.608268] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [121.608272] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [121.608423] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [121.633048] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [121.633053] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [121.633177] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [121.633321] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected <7> [132.676622] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [132.683854] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [132.708889] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [132.717529] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [132.718234] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [132.719076] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.720389] [drm:drm_mode_setcrtc] [CRTC:51:pipe A] <7> [132.720384] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.720855] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [132.721149] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.721517] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [132.722226] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [132.722970] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [132.723338] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [132.723707] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [132.724448] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.724722] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [132.725903] [drm:drm_mode_setcrtc] [CRTC:72:pipe B] <7> [132.728575] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [132.753043] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [132.757800] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [132.758005] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.758167] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [132.758632] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [132.759226] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [132.759414] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [132.759575] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [132.760202] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.760408] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [132.760974] [drm:drm_mode_setcrtc] [CRTC:93:pipe C] <7> [132.760998] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [132.764084] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [132.788562] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [132.793549] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [132.793742] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.794302] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [132.794833] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [132.795377] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [132.796586] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [132.797736] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [132.798570] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [132.798826] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [132.799036] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [132.799237] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [132.799909] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.800128] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [132.800152] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [132.800342] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.801512] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [132.801691] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [132.802474] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [132.803015] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [132.803021] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [132.803197] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [132.827272] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [132.827277] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [132.827405] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.827557] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6 <7> [132.827584] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [132.830793] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [132.855248] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [132.859995] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [132.860237] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.860403] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [132.860894] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [132.861456] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [132.861623] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [132.861804] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [132.862417] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.862596] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [132.863613] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [132.871973] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [132.896384] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [132.900446] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [132.900623] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.901147] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.901333] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [132.901353] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [132.901516] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.902048] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [132.902539] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [132.903121] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [132.904418] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [132.905493] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [132.906263] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [132.906439] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [132.906596] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [132.906764] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [132.907372] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.907536] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [132.907552] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [132.907700] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.908846] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [132.908989] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [132.909363] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [132.909846] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [132.909851] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [132.909976] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [132.935092] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [132.935099] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [132.935241] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.935388] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6 <7> [132.935407] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [132.935538] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.936045] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.936270] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [132.936284] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [132.936446] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.936966] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [132.937442] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [132.938040] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [132.939115] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [132.940202] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [132.940824] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [132.940999] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [132.941143] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [132.941287] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [132.941910] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.942103] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [132.942117] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [132.942253] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [132.943858] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [132.944013] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [132.945221] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [132.945743] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [132.945756] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [132.945922] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [132.972166] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [132.972171] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [132.972308] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [132.972556] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6 <7> [132.972572] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [132.975441] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [133.064902] [drm:drm_mode_setcrtc] [CRTC:51:pipe A] <7> [133.076922] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [133.082332] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [133.082662] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.082948] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.083606] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.084288] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.084547] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.084819] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.085525] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.085817] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [133.086887] [drm:drm_mode_setcrtc] [CRTC:72:pipe B] <7> [133.090129] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [133.114707] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [133.119738] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [133.120043] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.120314] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.120909] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.121563] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.121833] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.122129] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.122846] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.123237] [drm:drm_mode_setcrtc] [CRTC:93:pipe C] <7> [133.123260] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [133.123270] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [133.126359] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [133.150819] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [133.155741] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [133.155939] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.156442] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.156622] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [133.156643] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [133.156821] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.157386] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.157918] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.158456] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [133.159593] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [133.160735] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [133.161445] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [133.161648] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.161848] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.162026] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.162656] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.162865] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [133.162892] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [133.166580] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [133.191095] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [133.196047] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [133.196272] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.196466] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.196979] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.197550] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.197737] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.197934] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.198576] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.198832] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [133.199399] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [133.202684] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [133.227104] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [133.231947] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [133.232127] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.233320] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.233522] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [133.234301] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.234848] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.234856] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [133.235031] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [133.260235] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.260242] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [133.260403] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.260593] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6 <7> [133.260620] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [133.260823] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.261404] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.261597] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [133.261615] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [133.261805] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.262320] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.262847] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.263408] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [133.264720] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [133.265717] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [133.266503] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [133.266684] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.266859] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.267019] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.267631] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.267821] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [133.267837] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [133.268016] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.269280] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.269407] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [133.270175] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.270638] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.270642] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [133.270779] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [133.297607] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.297613] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [133.297739] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.297945] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6 <7> [133.297981] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [133.300805] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [133.412600] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [133.418712] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [133.419361] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [133.419657] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.420063] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.421082] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.421893] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [133.421938] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [133.422460] [drm:drm_mode_setcrtc] [CRTC:51:pipe A] <7> [133.422457] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [133.424174] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [133.425085] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [133.425715] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [133.426027] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.426287] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.426541] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.427375] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.427654] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [133.427855] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.428135] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.428716] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.429369] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.429652] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.429961] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.430726] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.430977] [drm:drm_mode_setcrtc] [CRTC:72:pipe B] <7> [133.430931] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [133.433323] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [133.456856] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [133.460370] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [133.460543] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.460685] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.461159] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.461726] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.461880] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.462025] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.462635] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.462819] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [133.463998] [drm:drm_mode_setcrtc] [CRTC:93:pipe C] <7> [133.464002] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [133.465306] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [133.489793] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [133.495615] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [133.495789] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.496944] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.497116] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [133.497907] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.498420] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.498426] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [133.498591] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [133.524875] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.524882] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [133.525033] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.525215] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6 <7> [133.525242] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [133.525402] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.525923] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.526210] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.526331] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [133.526379] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.526852] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.527412] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.527565] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.527716] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.528337] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.528503] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [133.529118] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [133.530795] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [133.555163] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [133.559795] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [133.559937] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.560423] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.560952] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.561538] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [133.562782] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [133.563780] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [133.564540] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [133.564741] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.564945] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.565092] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.565692] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.565864] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [133.565882] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [133.566020] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.567079] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.567216] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [133.567954] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.568462] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.568468] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [133.568595] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [133.596004] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.596009] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [133.596135] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.596283] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6 <7> [133.596303] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [133.596438] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.596915] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.597112] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [133.597126] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [133.597296] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.597824] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.598327] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.598937] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [133.600111] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [133.601201] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [133.601948] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [133.602116] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.602304] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.602482] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.603109] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.603289] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [133.603303] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [133.603440] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.604580] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.604707] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [133.605119] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.605627] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.605630] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [133.605770] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [133.633665] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.633670] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [133.633855] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.634039] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6 <7> [133.634093] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [133.637784] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [133.742873] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [133.749371] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [133.749734] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.750017] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.750659] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.751316] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.751565] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.751830] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.752531] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <6> [133.753338] [IGT] i915_pm_rpm: exiting, ret=0 <7> [133.755281] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.755537] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.756167] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.756861] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.757148] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.757428] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.758186] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <6> [133.759020] Console: switching to colour frame buffer device 128x48 <7> [133.759441] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.759731] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.760315] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.760954] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.761213] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.761466] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.762197] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.762643] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [133.762916] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.763614] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.763853] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [133.763884] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [133.764091] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.764640] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [133.765188] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [133.765786] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [133.767020] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [133.768029] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [133.768699] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [133.769040] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [133.769260] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [133.769460] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [133.770148] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [133.770378] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [133.770400] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [133.770613] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [133.771870] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.772058] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [133.772850] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [133.773382] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [133.773389] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [133.773587] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

Created at 2023-06-05 22:57:30