Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Igt-Version |
IGT-Version: 1.27.1-gc2d8ef8b9 (x86_64) (Linux: 6.4.0-rc5-linus-v6.4-rc5-g9561de3a55be+ x86_64) |
| Out |
Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: yes Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x76/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa2d/0xd10 [i915] intel_atomic_commit+0x380/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 0 Subtest basic-rte: SUCCESS (1.907s) i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: yes Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x76/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa2d/0xd10 [i915] intel_atomic_commit+0x380/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 0 |
| Err |
Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.907s) |
| Dmesg |
<6> [110.869795] Console: switching to colour dummy device 80x25
<6> [110.870271] [IGT] i915_pm_rpm: executing
<6> [110.874037] [IGT] i915_pm_rpm: starting subtest basic-rte
<7> [110.874103] i915 0000:03:00.0: [drm:i915_gem_open [i915]]
<7> [110.874927] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1]
<7> [110.874946] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [110.875073] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.875973] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.876103] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1] disconnected
<7> [110.876228] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1]
<7> [110.876239] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [110.876354] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.877764] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.877894] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] disconnected
<7> [110.878018] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2]
<7> [110.878030] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [110.878143] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.879083] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.879226] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] disconnected
<7> [110.879340] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2]
<7> [110.879351] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [110.879467] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.880568] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.880697] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2] disconnected
<7> [110.880809] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3]
<7> [110.880820] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [110.880978] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.882114] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.882242] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] disconnected
<7> [110.882355] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3]
<7> [110.882366] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [110.882481] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.883622] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.883780] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3] disconnected
<7> [110.883894] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4]
<7> [110.883914] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [110.884030] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.885158] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.885317] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] disconnected
<7> [110.899509] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1]
<7> [110.899525] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [110.899655] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.900554] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.900683] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1] disconnected
<7> [110.901445] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1]
<7> [110.901458] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [110.901577] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.902486] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.902615] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] disconnected
<7> [110.903336] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2]
<7> [110.903347] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [110.903462] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.904371] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.904499] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] disconnected
<7> [110.905224] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2]
<7> [110.905236] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [110.905352] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.906351] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.906480] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2] disconnected
<7> [110.907208] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3]
<7> [110.907220] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [110.907338] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.908245] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.908374] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] disconnected
<7> [110.909198] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3]
<7> [110.909211] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [110.909330] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.910245] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.910386] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3] disconnected
<7> [110.911157] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4]
<7> [110.911170] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [110.911286] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.912245] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.912374] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] disconnected
<7> [110.913357] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1]
<7> [110.913370] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [110.913487] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.914385] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.914513] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1] disconnected
<7> [110.914540] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1]
<7> [110.914551] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [110.914665] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.915924] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.916083] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] disconnected
<7> [110.916110] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2]
<7> [110.916120] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [110.916235] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.917462] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.917605] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] disconnected
<7> [110.917631] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2]
<7> [110.917642] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [110.917759] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.918983] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.919124] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2] disconnected
<7> [110.919153] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3]
<7> [110.919164] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [110.919278] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.920515] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.920656] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] disconnected
<7> [110.920682] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3]
<7> [110.920693] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [110.920810] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.922078] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.922207] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3] disconnected
<7> [110.922233] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4]
<7> [110.922244] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [110.922360] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.923552] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.923680] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] disconnected
<7> [111.925063] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [111.927511] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [111.933608] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [111.935199] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [111.935355] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [111.935520] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [111.935654] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [111.935785] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [111.935945] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [111.936112] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [111.936257] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [111.936445] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [111.936793] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [111.938498] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [111.938721] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [111.938905] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [111.939150] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [111.939332] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [111.987204] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [111.987287] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [111.987409] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [111.987568] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [111.988134] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [111.988292] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [111.988422] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [111.988846] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [111.990314] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [111.990433] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.007302] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.008822] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [112.010297] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.010388] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.011839] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.012006] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1
<7> [112.012023] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [112.012141] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.013372] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.013533] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6
<7> [112.013547] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [112.013663] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.014897] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.015035] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1
<7> [112.015049] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [112.015165] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.016413] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.016543] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1
<7> [112.016556] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [112.016670] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.018005] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.018185] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1
<7> [112.018200] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [112.018329] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.019511] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.019652] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1
<7> [112.019666] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [112.019791] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.021061] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.021235] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1
<7> [112.022657] [drm:drm_mode_setcrtc] [CRTC:98:pipe A]
<7> [112.022791] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.022939] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.024045] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.025652] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.025796] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.025974] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.026110] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.026245] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.026383] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.026519] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.026654] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.026784] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.026925] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.027081] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.028667] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.028816] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.031701] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.034819] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.036329] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.036484] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.036635] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.036781] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.036966] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.037133] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.037282] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.037436] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.037645] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.037849] [drm:drm_mode_setcrtc] [CRTC:167:pipe B]
<7> [112.038096] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.039662] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.039861] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.040089] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.040210] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.040376] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.064130] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.064213] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.064337] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.064498] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.065029] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.065173] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.065292] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.065647] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.067018] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.067139] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.084008] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.085534] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.085649] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.085768] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.087025] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.088622] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.088765] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.088904] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.089048] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.089183] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.089322] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.089456] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.089591] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.089718] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.089851] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.090015] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.091582] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.091716] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.094620] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.097749] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.099252] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.099395] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.099535] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.099672] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.099806] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.099996] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.100130] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.100264] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.100455] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.100644] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [112.100794] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.100991] [drm:drm_mode_setcrtc] [CRTC:236:pipe C]
<7> [112.102515] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.102710] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.102895] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.103065] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.103232] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.127127] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.127211] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.127337] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.127501] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.128050] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.128196] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.128315] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.128602] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.129970] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.130092] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.146962] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.149964] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.150050] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.151495] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.151753] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.151871] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.153006] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.154592] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.154735] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.154876] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.155020] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.155154] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.155293] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.155428] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.155563] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.155691] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.155824] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.155951] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.157520] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.157685] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1
<7> [112.157709] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.158342] [drm:drm_mode_setcrtc] [CRTC:305:pipe D]
<7> [112.160581] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.165171] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.166717] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.166860] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.167009] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.167176] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.167310] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.167448] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.167582] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.167715] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.167914] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.168182] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.169809] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.170012] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.170199] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.170321] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.170486] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.217760] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.217844] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.217980] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.218144] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.218663] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.218807] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.218958] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.219315] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.220665] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.220787] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.237651] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.240652] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.240771] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.240889] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.242172] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.243755] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.243921] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.244074] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.244211] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.244346] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.244485] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.244620] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.244755] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.244884] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.245032] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.245151] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.246740] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.247049] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.249775] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.252880] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.254390] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.254533] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.254672] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.254808] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.254949] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.255087] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.255220] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.255354] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.255546] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.255765] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [112.256309] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.257944] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.258139] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.258325] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.258448] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.258612] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.282079] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.282163] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.282288] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.282451] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.282996] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.283143] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.283262] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.283561] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.284931] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.285052] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.303460] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.306495] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.306582] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.308029] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.308164] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6
<7> [112.308181] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [112.308296] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.309512] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.309642] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1
<7> [112.309657] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [112.309775] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.311047] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.311191] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1
<7> [112.311205] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [112.311318] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.312563] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.312693] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1
<7> [112.312707] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [112.312822] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.314079] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.314210] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1
<7> [112.314224] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [112.314337] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.315617] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.315747] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1
<7> [112.315768] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [112.315884] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.317132] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.317261] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1
<7> [112.317275] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [112.317388] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.318668] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.318797] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6
<7> [112.318811] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [112.318959] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.320193] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.320322] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1
<7> [112.320336] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [112.320452] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.321712] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.321842] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1
<7> [112.321856] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [112.321978] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.323245] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.323376] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1
<7> [112.323390] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [112.323506] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.324763] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.324959] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1
<7> [112.324973] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [112.325089] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.326330] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.326495] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1
<7> [112.326510] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.329376] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.333979] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.335490] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.335633] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.335773] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.335915] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.336086] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.336224] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.336358] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.336492] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.336683] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.337026] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.338641] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.338835] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.339031] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.339153] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.339319] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.356378] [drm:drm_mode_setcrtc] [CRTC:98:pipe A]
<7> [112.386993] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.387078] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.387202] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.387364] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.387882] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.388037] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.388157] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.388441] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.389788] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.389917] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.406783] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.409801] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.409929] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.410079] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.411305] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.412888] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.413035] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.413176] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.413313] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.413447] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.413586] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.413721] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.413855] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.413991] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.414124] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.414243] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.415814] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.415953] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.418850] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.423441] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.425040] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.425182] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.425321] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.425458] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.425592] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.425730] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.425865] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.426006] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.426199] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.426387] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [112.426510] [drm:drm_mode_setcrtc] [CRTC:167:pipe B]
<7> [112.426552] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.428011] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.428205] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.428391] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.428513] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.428680] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.452071] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.452155] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.452281] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.452446] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.452988] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.453134] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.453253] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.453527] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.454890] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.455055] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.471923] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.474927] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.475050] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.476482] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.476753] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.476871] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.477997] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.479587] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.479730] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.479870] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.480048] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.480183] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.480322] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.480456] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.480592] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.480720] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.480852] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.481017] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.482610] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1
<7> [112.484147] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.484283] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.487175] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.491754] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.493387] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.493545] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.493686] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.493822] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.493995] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.494134] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.494269] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.494403] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.494595] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.494805] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [112.494978] [drm:drm_mode_setcrtc] [CRTC:236:pipe C]
<7> [112.495054] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.496631] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.496829] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.497116] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.497241] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.497407] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.521098] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.521214] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.521340] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.521506] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.522090] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.522240] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.522361] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.522650] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.524061] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.524184] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.541050] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.542562] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.542649] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.544074] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.544347] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.544466] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.545593] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.547188] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.547331] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.547470] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.547606] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.547741] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.547879] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.548083] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.548234] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.548362] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.548495] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.548615] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.550191] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6
<7> [112.551741] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.551917] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.554745] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.557864] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.559375] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.559518] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.559658] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.559794] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.559934] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.560073] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.560208] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.560342] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.560534] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.560720] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [112.560883] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.561057] [drm:drm_mode_setcrtc] [CRTC:305:pipe D]
<7> [112.562521] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.562717] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.562904] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.563036] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.563201] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.587071] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.587155] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.587280] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.587445] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.588018] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.588166] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.588286] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.588616] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.589984] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.590106] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.606976] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.608487] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.608570] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.609996] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.610319] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.610438] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.611500] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.613082] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.613226] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.613366] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.613502] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.613638] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.613776] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.613918] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.614085] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.614213] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.614345] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.614464] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.616022] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1
<7> [112.616068] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.616203] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.619129] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.622192] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.623703] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.623846] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.623994] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.624131] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.624265] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.624404] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.624539] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.624674] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.624866] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.625081] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [112.625238] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.626870] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.627069] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.627255] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.627378] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.627542] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.651071] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.651154] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.651279] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.651443] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.652016] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.652163] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.652282] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.652618] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.653987] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.654109] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.670979] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.672490] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.672574] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.674011] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.674157] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1
<7> [112.674174] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [112.674289] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.675554] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.675715] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1
<7> [112.675729] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [112.675845] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.677038] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.677169] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1
<7> [112.677183] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [112.677296] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.678574] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.678704] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1
<7> [112.678726] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [112.678842] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.680089] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.680219] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1
<7> [112.680234] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [112.680348] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.681628] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.681760] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6
<7> [112.681773] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [112.681889] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.683160] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.683292] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1
<7> [112.683306] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [112.683421] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.684670] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.684836] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1
<7> [112.684850] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [112.684973] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.686224] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.686367] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1
<7> [112.686381] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [112.686496] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.687720] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.687849] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1
<7> [112.687863] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [112.687985] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.689255] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.689384] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1
<7> [112.689400] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.692307] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.698424] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.699972] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.700114] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.700254] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.700392] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.700526] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.700666] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.700801] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.700969] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.701175] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.701510] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.702973] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.703167] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.703355] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.703478] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.703643] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.750993] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.751080] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.751204] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.751365] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.751879] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.752034] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.752154] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.752479] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.753824] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.753951] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.769290] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.770808] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [112.772285] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.772374] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.773826] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.773964] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1
<7> [112.773980] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [112.774098] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.775355] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.775485] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6
<7> [112.775499] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [112.775612] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.776881] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.777050] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1
<7> [112.777064] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [112.777180] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.778398] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.778557] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1
<7> [112.778558] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.778572] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [112.779967] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1
<7> [112.779998] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [112.781517] [drm:drm_mode_setcrtc] [CRTC:98:pipe A]
<7> [112.781470] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.781616] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1
<7> [112.781643] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [112.781757] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.782994] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.783126] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1
<7> [112.783142] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.786039] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.792138] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.793740] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.793883] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.794080] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.794218] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.794353] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.794492] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.794626] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.794761] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.794995] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.795362] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.796993] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.797188] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.797374] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.797497] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.797662] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.821065] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.821147] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.821270] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.821431] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.821959] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.822103] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.822222] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.822566] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.823921] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.824042] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.840915] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.843937] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.844054] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.844174] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.845433] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.847014] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.847158] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.847298] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.847435] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.847570] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.847708] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.847841] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.847984] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.848114] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.848246] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.848364] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.849957] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.850104] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.852981] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.856089] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.857600] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.857743] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.857882] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.858027] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.858161] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.858299] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.858432] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.858566] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.858759] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.858993] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [112.859139] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.859303] [drm:drm_mode_setcrtc] [CRTC:167:pipe B]
<7> [112.860668] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.860862] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.861091] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.861213] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.861379] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.885751] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.885834] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.885973] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.886138] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.886672] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.886817] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.886945] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.887408] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.888772] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.888893] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.905780] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.908773] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.908858] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.910306] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.910568] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.910687] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.911820] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.913440] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.913583] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.913722] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.913858] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.914043] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.914183] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.914318] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.914453] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.914581] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.914714] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.914833] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.916397] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1
<7> [112.916442] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.916576] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.919514] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.924032] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.925608] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.925751] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.925890] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.926042] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.926217] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.926356] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.926489] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.926623] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.926815] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.927045] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [112.927167] [drm:drm_mode_setcrtc] [CRTC:236:pipe C]
<7> [112.927240] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.928886] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.929144] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.929330] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.929452] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.929616] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [112.952142] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [112.952225] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [112.952350] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [112.952515] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [112.953063] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [112.953211] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [112.953332] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [112.953691] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [112.955064] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.955187] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.972054] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [112.973565] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [112.973649] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.975111] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.975368] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.975486] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.976578] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.978189] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.978332] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.978471] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.978608] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.978741] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.978880] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.979023] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.979158] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.979285] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.979416] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [112.979536] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [112.981104] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.981272] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6
<7> [112.981295] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [112.981971] [drm:drm_mode_setcrtc] [CRTC:305:pipe D]
<7> [112.984178] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [112.988711] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [112.990298] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.990440] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [112.990579] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.990716] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [112.990849] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.991033] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [112.991167] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.991301] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [112.991492] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [112.991822] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [112.993458] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [112.993653] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [112.993839] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [112.993970] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [112.994164] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.042813] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.042897] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.043036] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.043199] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.043719] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.043863] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.043991] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.044303] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.045650] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [113.045770] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [113.062636] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.065636] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.065755] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.065873] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.067171] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [113.068838] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.069018] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.069158] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.069294] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.069428] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.069566] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [113.069700] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.069835] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [113.069971] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.070104] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [113.070222] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [113.071789] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.071929] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.074852] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.077954] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [113.079465] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.079608] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.079748] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.079885] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.080026] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.080166] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [113.080301] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.080435] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [113.080627] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.080841] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [113.081332] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.083011] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [113.083206] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.083392] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.083514] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.083677] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.107153] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.107237] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.107362] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.107526] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.108106] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.108254] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.108374] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.108806] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.110180] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [113.110303] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [113.127178] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.128686] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.128771] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.130199] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.130371] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1
<7> [113.130388] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [113.130505] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.131710] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.131841] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1
<7> [113.131856] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [113.131979] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.133245] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.133374] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1
<7> [113.133388] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [113.133504] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.134761] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.134918] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1
<7> [113.134932] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [113.135063] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.136321] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.136464] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1
<7> [113.136485] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [113.136600] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.137833] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.138017] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1
<7> [113.138031] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [113.138146] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.139349] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.139478] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6
<7> [113.139492] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [113.139606] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.140884] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.141061] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1
<7> [113.141075] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [113.141192] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.142420] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.142550] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1
<7> [113.142563] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [113.142679] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.143962] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.144123] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1
<7> [113.144136] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [113.144252] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.145440] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.145569] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1
<7> [113.145583] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [113.145696] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.147007] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.147137] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1
<7> [113.147152] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.150011] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.153136] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [113.154640] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.154783] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.154929] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.155105] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.155240] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.155377] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [113.155512] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.155646] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [113.155838] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.156161] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.157613] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [113.157804] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.157995] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.158117] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.158281] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.205462] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.205659] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.205786] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.206005] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.206577] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.206783] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.206904] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.207437] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.208796] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [113.208947] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [113.231932] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.238020] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1]
<7> [113.239509] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.239733] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.241068] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.241213] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1
<7> [113.241231] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1]
<7> [113.241345] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.242611] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.242742] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6
<7> [113.242757] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2]
<7> [113.242871] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.244122] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.244264] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1
<7> [113.244278] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2]
<7> [113.244394] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.245646] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.245790] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1
<7> [113.245804] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3]
<7> [113.245977] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.247177] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.247326] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1
<7> [113.247340] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3]
<7> [113.247456] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.248706] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.248835] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1
<7> [113.248849] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4]
<7> [113.248972] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.250207] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.250337] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1
<7> [113.432701] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.432851] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.433783] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [113.435422] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.435580] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.435719] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.435855] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.436045] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.436198] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [113.436332] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.436465] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [113.436610] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.436770] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [113.436887] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [113.438538] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [113.439065] [IGT] i915_pm_rpm: exiting, ret=0
<7> [113.440676] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.440801] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.441809] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [113.443423] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.443581] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.443749] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.443884] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.444091] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.444244] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [113.444378] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.444510] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [113.444654] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.444786] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [113.444903] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [113.446580] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [113.446900] Console: switching to colour frame buffer device 128x48
<7> [113.447859] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.448040] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.448958] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [113.450581] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.450754] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.450937] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.451103] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.451235] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.451373] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [113.451506] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.451640] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [113.451782] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.451946] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [113.452092] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [113.453734] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
|