Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g766edf969 (x86_64) (Linux: 6.4.0-rc4-linus-v6.4-rc4-g7877cb91f108+ x86_64)
Out 
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.521s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.521s)
Dmesg
<6> [164.162000] Console: switching to colour dummy device 80x25
<6> [164.162211] [IGT] kms_force_connector_basic: executing
<7> [164.165142] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [164.165568] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [164.165690] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [164.166151] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [164.166158] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.166173] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.217151] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.234288] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.234295] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.234411] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.251291] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.251294] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.251398] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [164.251455] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.251471] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.303151] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.320295] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.320298] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.320402] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.337291] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.337294] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.337392] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [164.337454] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.337469] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.388342] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.405304] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.405308] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.405415] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.422300] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.422303] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.422406] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<6> [164.422640] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [164.422743] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [164.422748] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.422760] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.474165] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.491293] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.491307] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.491467] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.508245] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.508251] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.508353] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] status updated from disconnected to connected
<7> [164.508477] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [164.508491] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [164.508497] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [164.508501] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [164.508504] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [164.508508] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [164.508545] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.508561] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.560167] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.577292] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.577306] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.577465] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.594287] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.594293] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.594426] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [164.594439] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [164.594443] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [164.594445] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [164.594447] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [164.594450] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [164.594599] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:258:HDMI-A-1] EDID override set
<7> [164.594614] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.594625] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.594744] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD monitor IGT
<7> [164.594748] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD size 24, SAD count 0
<7> [164.645146] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.662278] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [164.662362] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [164.662368] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [164.662374] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [164.662377] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [164.662382] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [164.662397] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [164.662401] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [164.662404] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [164.662407] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [164.662410] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [164.662412] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [164.662541] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:258:HDMI-A-1] EDID override set
<7> [164.662562] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.662575] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.662735] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD monitor IGT
<7> [164.662738] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD size 24, SAD count 0
<7> [164.662741] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:258:HDMI-A-1] EDID changed, epoch counter 4
<7> [164.674104] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [164.674349] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0040 w(1)
<7> [164.674512] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -110)
<7> [164.674609] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [164.674615] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [164.674622] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [164.674642] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [164.674646] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [164.674650] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [164.674654] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [164.674657] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [164.674799] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:258:HDMI-A-1] EDID override reset
<7> [164.674826] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.674843] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.686145] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [164.686330] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [164.737143] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.754322] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.754333] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.754496] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.771269] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.771275] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.771374] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:258:HDMI-A-1] EDID changed, epoch counter 5
<7> [164.771412] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [164.771416] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [164.771421] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [164.771423] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [164.771428] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [164.771440] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [164.771443] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [164.771445] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [164.771448] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [164.771450] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [164.771584] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [164.771590] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.771605] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.823146] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.840301] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.840306] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.840444] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.857276] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.857280] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.857383] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] status updated from connected to disconnected
<7> [164.857404] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [164.857515] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.857532] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.909209] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.926243] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.926253] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.926445] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.943298] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.943302] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.943402] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [164.943532] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [164.943987] [drm:status_store] [CONNECTOR:236:eDP-1] force updated from 0 to 0 or reprobing
<7> [164.943992] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [164.944006] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [164.944870] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [164.945012] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [164.945703] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [164.945809] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [164.945905] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [164.946025] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [164.946185] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [164.946190] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [164.946193] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [164.946196] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [164.946208] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [164.946307] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [164.947143] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [164.947242] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [164.947997] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [164.948010] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [164.948014] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [164.948039] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [164.948052] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [164.948920] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [164.949044] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [164.949690] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [164.949796] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [164.949890] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [164.950037] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [164.950147] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [164.950150] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [164.950153] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [164.950156] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [164.950165] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [164.950270] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [164.951102] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [164.951209] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [164.951916] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [164.951929] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [164.951940] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [164.952056] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:236:eDP-1] EDID override reset
<7> [164.952073] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [164.952086] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [164.952915] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [164.953031] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [164.953716] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [164.953817] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [164.953924] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [164.954050] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [164.954154] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [164.954160] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [164.954164] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [164.954168] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [164.954183] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [164.954318] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [164.955136] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [164.955240] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [164.955970] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [164.955981] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [164.955985] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [164.956091] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:246:DP-1] EDID override reset
<7> [164.956104] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [164.956115] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [164.956271] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [164.956369] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [164.956373] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.956384] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [165.007142] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [165.024277] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [165.024281] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [165.024381] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [165.041286] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [165.041289] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [165.041387] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [165.041436] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [165.041451] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [165.092164] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [165.109282] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [165.109286] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [165.109386] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [165.126316] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [165.126319] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [165.126414] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [165.126530] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:258:HDMI-A-1] EDID override reset
<7> [165.126550] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [165.126565] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [165.177143] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [165.194300] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [165.194307] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [165.194435] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [165.211262] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [165.211265] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [165.211387] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [165.211534] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:264:DP-2] EDID override reset
<7> [165.211555] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2]
<7> [165.211572] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-2]
<7> [165.211754] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2] disconnected
<7> [165.211828] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:273:DP-3] EDID override reset
<7> [165.211840] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3]
<7> [165.211850] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-3]
<7> [165.212006] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3] disconnected
<6> [165.212381] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [165.212469] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [165.212474] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [165.212487] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [165.263168] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [165.280301] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [165.280305] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [165.280413] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [165.297263] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [165.297267] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [165.297370] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [165.297441] [drm:status_store] [CONNECTOR:236:eDP-1] force updated from 0 to 0 or reprobing
<7> [165.297448] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [165.297464] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [165.298364] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [165.298468] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [165.299130] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [165.299227] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [165.299322] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [165.299414] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [165.299528] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [165.299533] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [165.299536] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [165.299539] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [165.299555] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [165.299651] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [165.300431] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [165.300526] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [165.301242] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [165.301255] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [165.301260] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [165.301436] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [165.318117] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [165.318135] [drm:drm_client_modeset_probe]
<7> [165.318176] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [165.318194] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [165.319156] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [165.319300] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [165.320142] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [165.320427] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [165.320703] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [165.321003] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [165.321336] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [165.321353] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [165.321364] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [165.321375] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [165.321420] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [165.321722] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [165.322609] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [165.322725] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [165.323481] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [165.323495] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [165.323499] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [165.323503] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [165.323515] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [165.323679] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [165.323691] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [165.323702] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [165.375160] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [165.392293] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [165.392297] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [165.392408] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [165.409244] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [165.409247] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [165.409344] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [165.409357] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2]
<7> [165.409369] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-2]
<7> [165.409514] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2] disconnected
<7> [165.409525] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3]
<7> [165.409534] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-3]
<7> [165.409677] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3] disconnected
<7> [165.409687] [drm:drm_client_modeset_probe] connector 236 enabled? yes
<7> [165.409690] [drm:drm_client_modeset_probe] connector 246 enabled? no
<7> [165.409692] [drm:drm_client_modeset_probe] connector 258 enabled? no
<7> [165.409694] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [165.409695] [drm:drm_client_modeset_probe] connector 273 enabled? no
<7> [165.409725] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [165.409735] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 236
<7> [165.409737] [drm:drm_client_modeset_probe] looking for preferred mode on connector 236 0
<7> [165.409739] [drm:drm_client_modeset_probe] found mode 1920x1080
<7> [165.409741] [drm:drm_client_modeset_probe] picking CRTCs for 1920x1080 config
<7> [165.409757] [drm:drm_client_modeset_probe] desired mode 1920x1080 set on crtc 80 (0,0)
<6> [165.435041] Console: switching to colour frame buffer device 240x67
Created at 2023-05-28 13:39:07