Results for igt@i915_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g766edf969 (x86_64) (Linux: 6.4.0-rc4-linus-v6.4-rc4-g7877cb91f108+ x86_64)
Out 
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: yes
Usage count: 0
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x76/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   untrack_all_intel_runtime_pm_wakerefs+0x42/0x80 [i915]
   intel_runtime_suspend+0xe6/0x240 [i915]
   pci_pm_runtime_suspend+0x5a/0x1a0
   __rpm_callback+0x3c/0x110
   rpm_callback+0x58/0x70
   rpm_suspend+0x118/0x5f0
   pm_runtime_work+0x9f/0xb0
Wakeref count: 0
Subtest basic-rte: SUCCESS (2.422s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 0
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x76/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x159/0x2b0 [i915]
   intel_atomic_commit_tail+0xa2d/0xd10 [i915]
   intel_atomic_commit+0x380/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
Wakeref count: 0
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (2.422s)
Dmesg
<6> [123.261277] Console: switching to colour dummy device 80x25
<6> [123.261394] [IGT] i915_pm_rpm: executing
<6> [123.265244] [IGT] i915_pm_rpm: starting subtest basic-rte
<7> [123.265341] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [123.266132] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [123.266164] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [123.266471] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.267046] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.267595] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.268161] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [123.268964] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [123.269215] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [123.270226] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.271821] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.273517] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.275159] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.276994] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.278822] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.280483] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.282226] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.283814] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.284713] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [123.285620] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [123.286276] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [123.286783] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [123.286984] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [123.287204] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [123.287387] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [123.288054] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.288269] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [123.288403] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2]
<7> [123.288419] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [123.288608] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.289148] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.289324] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected
<7> [123.289411] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1]
<7> [123.289427] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [123.289602] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.340679] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [123.358240] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.358253] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [123.358934] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [123.376036] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.376051] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [123.376339] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.376675] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [123.385777] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [123.385809] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [123.386097] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.386701] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.387274] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.387864] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [123.388692] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [123.388949] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [123.389960] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.391488] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.393149] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.394799] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.396484] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.398366] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.400238] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.401986] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.403484] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.404383] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [123.405467] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [123.406171] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [123.406839] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [123.407075] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [123.407317] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [123.407577] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [123.408273] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.408540] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [123.409747] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2]
<7> [123.409775] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [123.410029] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.410609] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.410864] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected
<7> [123.411950] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1]
<7> [123.411977] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [123.412223] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.463675] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [123.480736] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.480750] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [123.480998] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [123.498011] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.498019] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [123.498250] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.498532] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [123.499329] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [123.499357] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [123.499624] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.500198] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.500759] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.501326] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [123.502147] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [123.502399] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [123.503420] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.505035] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.506685] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.508335] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.510074] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.511819] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.513477] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.515317] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.516925] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.517723] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [123.518493] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [123.519191] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [123.519745] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [123.520033] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [123.520214] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [123.520479] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [123.521174] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.521433] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [123.521517] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2]
<7> [123.521542] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [123.521782] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.522347] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.522624] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected
<7> [123.522680] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1]
<7> [123.522704] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [123.522940] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.574683] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [123.591697] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.591707] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [123.591878] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [123.607689] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.607696] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [123.607851] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.608022] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [124.609801] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [124.620671] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [124.645618] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [124.653084] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [124.653881] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [124.654639] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [124.655588] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [124.655725] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [124.656701] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [124.657726] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [124.659185] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [124.659887] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [124.661099] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.662777] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.664433] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.666249] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.668562] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.670648] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.672429] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.674225] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.675888] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.677118] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [124.678222] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [124.679150] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [124.679997] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [124.680677] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [124.681165] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [124.681677] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [124.682825] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [124.683263] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [124.683707] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [124.688317] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [124.712373] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [124.717160] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [124.717410] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [124.717662] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [124.718201] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [124.718820] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [124.719067] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [124.719301] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [124.720007] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [124.720349] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [124.721285] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [124.724237] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [124.748957] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [124.755020] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [124.755217] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [124.755375] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [124.755892] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [124.756513] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [124.756721] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [124.756879] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [124.757506] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [124.757768] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [124.758916] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [124.759039] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [124.761498] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [124.785948] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [124.792501] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [124.792653] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [124.793152] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [124.793340] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [124.793366] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [124.793555] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [124.845663] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [124.869411] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [124.869435] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [124.869948] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [124.889473] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [124.889482] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [124.889652] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [124.889844] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [124.889891] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [124.895511] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [124.919951] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [124.926026] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [124.926223] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [124.926381] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [124.926874] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [124.927484] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [124.927693] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [124.927851] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [124.928483] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [124.928709] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [124.929910] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [124.934505] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [124.958915] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [124.965526] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [124.965684] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [124.966194] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [124.966738] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [124.967327] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [124.968119] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [124.968299] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [124.969311] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.970991] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.972485] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.973917] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.975663] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.977489] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.979271] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.981088] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.982707] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [124.983662] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [124.984503] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [124.985252] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [124.985761] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [124.986006] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [124.986184] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [124.986419] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [124.987169] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [124.987420] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [124.987467] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [124.987703] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [124.988212] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [124.988410] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [124.988432] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [124.988654] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.039676] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [125.056683] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.056694] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [125.056866] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [125.073230] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.073238] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [125.073391] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.073609] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [125.073654] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [125.073894] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.074465] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.074973] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.075569] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [125.076348] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [125.076542] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [125.077500] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.078896] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.080435] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.082093] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.083818] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.085770] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.087475] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.089255] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.090813] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.091822] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [125.092640] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [125.093318] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [125.093847] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [125.094092] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.094256] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.094414] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.095053] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.095311] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [125.095343] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [125.095645] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.096169] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.096341] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [125.096361] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [125.096546] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.147571] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [125.164583] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.164593] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [125.164763] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [125.181184] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.181192] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [125.181346] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.181581] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [125.181617] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [125.187508] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [125.231174] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [125.242718] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [125.250049] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [125.250367] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.250717] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.251440] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.252189] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.252566] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.253000] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.253999] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.254564] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [125.256212] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [125.263547] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [125.287945] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [125.296577] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [125.296869] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.297137] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.297736] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.298549] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.298885] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.299182] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.299942] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.300290] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [125.301535] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [125.301956] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [125.306521] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [125.330880] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [125.337514] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [125.337669] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.338173] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.338722] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.339313] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [125.340089] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [125.340263] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [125.341300] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.342938] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.344491] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.346152] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.347935] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.349783] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.351485] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.353280] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.354624] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.355767] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [125.356582] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [125.357287] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [125.357858] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [125.358120] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.358286] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.358470] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.359136] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.359406] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [125.359648] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.359893] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.360429] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.361026] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.361269] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.361515] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.362209] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.362571] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [125.362662] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [125.367168] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [125.390767] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [125.397516] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [125.397665] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.398156] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.398332] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [125.398355] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [125.398547] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.449661] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [125.468965] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.468982] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [125.469258] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [125.488041] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.488051] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [125.488241] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.488501] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [125.488555] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [125.488859] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.489525] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.490038] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.490685] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [125.491745] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [125.491928] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [125.492848] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.494487] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.496134] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.497719] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.499503] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.501270] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.503080] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.504815] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.506486] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.507371] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [125.508248] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [125.508907] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [125.509440] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [125.509680] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.509845] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.510002] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.510681] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.510947] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [125.510975] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [125.511135] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.511643] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.511826] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [125.511845] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [125.512036] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.563654] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [125.580098] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.580109] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [125.580277] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [125.596088] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.596095] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [125.596240] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.596418] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [125.596456] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [125.602462] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [125.675587] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [125.683021] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [125.683706] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [125.683988] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.684781] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.685631] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.686555] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [125.687409] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [125.687858] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [125.688278] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [125.689342] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.690834] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.692307] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.694082] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.695835] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.697610] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.699217] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.701004] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.702541] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.703501] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [125.704579] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [125.705253] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [125.705855] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [125.706335] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.706813] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.707255] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.708194] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.708708] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [125.708761] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [125.709170] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.710011] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.710527] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [125.711015] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.711538] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.712308] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.713193] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.713693] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.714161] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.715120] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.715683] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [125.715845] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [125.722470] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [125.746510] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [125.753012] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [125.753205] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.753361] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.753881] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.754488] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.754724] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.754951] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.755658] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.755920] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [125.755939] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [125.756131] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.807674] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [125.824163] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.824173] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [125.824343] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [125.840248] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.840255] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [125.840407] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.841143] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.841371] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.841888] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.842491] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.842685] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.842842] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.843470] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.844369] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [125.844400] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [125.844591] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.845117] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [125.845656] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [125.846205] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [125.846893] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [125.847056] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [125.847937] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.849486] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.851090] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.852675] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.854482] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.856315] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.858129] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.859962] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.861483] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [125.862342] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [125.863214] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [125.863885] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [125.864360] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [125.864597] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [125.864762] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [125.864921] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [125.865595] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.865862] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [125.865896] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [125.866087] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.866598] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.866774] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [125.866795] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [125.866949] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [125.918672] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [125.935190] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.935200] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [125.935370] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [125.951813] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [125.951821] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [125.951976] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [125.952153] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [125.952179] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [125.956404] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [126.072700] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [126.090542] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [126.090156] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [126.091810] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [126.092407] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [126.093309] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [126.094278] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [126.095013] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [126.096133] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [126.096792] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [126.099248] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [126.100893] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [126.102588] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [126.104286] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [126.106105] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [126.108224] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [126.110425] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [126.112362] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [126.114152] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [126.115126] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [126.116258] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [126.117046] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [126.117587] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [126.117896] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [126.118137] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [126.118371] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [126.119104] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [126.119417] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [126.119848] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [126.120085] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [126.120653] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [126.121315] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [126.121567] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [126.121808] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [126.122551] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [126.123585] [IGT] i915_pm_rpm: exiting, ret=0
<7> [126.123676] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [126.124015] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [126.124812] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [126.125142] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [126.125250] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [126.125594] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [126.176677] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [126.193196] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [126.193204] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [126.193374] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [126.209802] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [126.209808] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [126.209959] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [126.210137] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [126.210547] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [126.210792] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [126.211330] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [126.211967] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [126.212145] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [126.212304] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [126.212952] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [126.213312] Console: switching to colour frame buffer device 128x48
<7> [126.213847] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [126.214014] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [126.214493] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [126.215077] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [126.215239] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [126.215395] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [126.216049] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2023-05-28 13:39:07