Results for igt@i915_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g766edf969 (x86_64) (Linux: 6.4.0-rc4-linus-v6.4-rc4-g7877cb91f108+ x86_64)
Out 
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: yes
Usage count: 0
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x76/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   untrack_all_intel_runtime_pm_wakerefs+0x42/0x80 [i915]
   intel_runtime_suspend+0xe6/0x240 [i915]
   pci_pm_runtime_suspend+0x5a/0x1a0
   __rpm_callback+0x3c/0x110
   rpm_callback+0x58/0x70
   rpm_suspend+0x118/0x5f0
   pm_runtime_work+0x9f/0xb0
Wakeref count: 0
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.477s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.477s)
Dmesg
<6> [120.677352] Console: switching to colour dummy device 80x25
<6> [120.677757] [IGT] i915_pm_rpm: executing
<7> [120.681500] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [120.682161] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [120.682186] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [120.682387] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.682958] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [120.683496] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [120.684044] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [120.684868] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.685034] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [120.685933] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.687478] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.689050] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.690651] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.692408] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.694223] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.695980] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.697747] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.699354] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.700236] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.701060] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.701630] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.702128] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [120.702323] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [120.702506] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [120.702699] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [120.703317] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.703585] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [120.703718] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2]
<7> [120.703743] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [120.703946] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.704428] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.704626] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected
<7> [120.704747] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1]
<7> [120.704771] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [120.704966] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.756689] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [120.773114] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.773123] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [120.773293] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [120.789147] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.789154] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [120.789308] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.789536] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [120.795576] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [120.795599] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [120.795797] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.796287] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [120.796809] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [120.797382] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [120.798088] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.798253] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [120.799155] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.800765] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.802403] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.804041] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.805822] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.807735] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.809483] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.811228] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.812816] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.813826] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.814636] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.815300] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.815841] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [120.816133] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [120.816378] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [120.816644] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [120.817341] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.817559] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [120.818739] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2]
<7> [120.818767] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [120.819020] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.819598] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.819855] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected
<7> [120.820987] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1]
<7> [120.821014] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [120.821256] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.872678] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [120.889145] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.889154] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [120.889324] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [120.904647] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.904654] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [120.904802] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.904973] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [120.905637] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [120.905665] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [120.905907] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.906485] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [120.906972] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [120.907565] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [120.908266] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.908493] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [120.909406] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.910994] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.912482] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.914064] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.915812] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.917480] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.919258] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.921097] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.922735] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.923608] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.924506] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.925306] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.925807] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [120.926074] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [120.926238] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [120.926395] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [120.927063] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.927318] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [120.927386] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2]
<7> [120.927411] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [120.927659] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.928192] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.928370] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected
<7> [120.928410] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1]
<7> [120.928425] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [120.928703] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.979573] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [120.996598] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.996607] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [120.996775] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [121.012643] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.012650] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [121.012804] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [121.012977] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [122.018058] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.024782] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.049616] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.057815] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [122.058407] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.058962] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.060088] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [122.060214] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.060838] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.061419] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.062928] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.063133] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.063864] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.065477] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.067117] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.068769] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.070496] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.072380] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.074222] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.076059] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.077706] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.078645] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.079631] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.080319] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.080936] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.081387] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.081613] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.081847] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.082533] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.083089] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [122.083322] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.083598] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.084140] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.084746] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.084987] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.085222] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.085937] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.086758] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.090269] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [122.090262] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [122.091594] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.115944] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.121568] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.121722] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.122212] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.122392] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [122.122416] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [122.122699] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.174667] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.195047] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.195062] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.195328] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.214126] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.214136] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.214328] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.214886] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [122.215134] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.215470] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.216068] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.216740] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.217043] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.217323] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.218047] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.218297] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.220155] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [122.224624] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.249335] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.255044] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.255250] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.255409] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.255915] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.256518] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.256747] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.256935] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.257580] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.257843] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.259111] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [122.263508] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.288336] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.295516] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.295667] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.296159] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.296750] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.297309] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.298316] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.298541] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.299491] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.301106] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.302714] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.304332] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.306203] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.307984] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.309825] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.311483] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.313133] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.313999] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.314723] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.315403] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.315912] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.316129] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.316294] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.316489] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.317147] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.317413] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [122.317468] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [122.317704] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.318268] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.318544] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [122.318574] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [122.318763] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.369675] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.386670] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.386683] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.386927] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.403356] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.403364] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.403543] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.403808] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [122.403844] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [122.404005] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.404517] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.405049] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.405649] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.406364] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.406560] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.407497] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.408875] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.410487] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.411825] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.413644] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.415500] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.417398] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.419209] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.420815] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.421807] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.422670] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.423349] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.423880] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.424110] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.424335] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.424525] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.425172] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.425360] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [122.425383] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [122.425565] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.426066] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.426317] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [122.426343] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [122.426519] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.477669] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.494139] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.494150] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.494321] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.510771] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.510779] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.510930] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.511107] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [122.511134] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.515419] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [122.560799] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state
<7> [122.580164] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [122.591605] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.599045] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.599334] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.599640] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.600257] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.601003] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.601283] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.601570] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.602333] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.602748] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.604399] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [122.609520] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.633927] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.641557] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.641839] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.642081] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.642662] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.643353] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.643763] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.644086] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.644847] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.645216] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.647082] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [122.647107] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [122.652518] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.677106] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.682434] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.682605] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.683121] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.683669] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.684267] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.685142] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.685330] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.686326] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.687959] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.689660] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.691366] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.693211] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.695055] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.696823] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.698718] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.700338] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.701204] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.702068] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.702727] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.703249] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.703479] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.703679] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.703838] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.704514] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.704782] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [122.704954] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.705122] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.705607] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.706185] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.706391] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.706579] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.707240] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.707522] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.708817] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [122.711325] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.735600] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.740515] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.740684] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.741183] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.741368] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [122.741394] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [122.741617] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.792671] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.816951] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.816974] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.817487] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.838625] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.838636] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.838884] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.839163] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [122.839212] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [122.839487] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.840082] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.840615] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.841200] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.842077] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.842329] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.843349] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.845002] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.846671] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.848293] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.850264] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.852117] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.853970] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.855824] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.857564] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.858598] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.859641] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.860374] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.860957] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.861252] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.861521] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.861761] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.862478] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.862743] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [122.862776] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [122.863016] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.863605] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.863866] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [122.863895] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [122.864132] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.915675] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.933792] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.933805] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.934056] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.952132] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.952142] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.952374] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.952667] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [122.952704] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.956464] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [123.022913] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [123.032670] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [123.033348] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [123.034180] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.035092] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.035931] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.037330] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [123.038592] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [123.039126] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [123.040254] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.041809] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.043368] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.044855] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.046609] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.048284] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.050057] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.051809] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.053336] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [123.054171] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [123.054422] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [123.055885] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [123.056817] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [123.057768] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [123.057823] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [123.058307] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:108:DP-2] Same epoch counter 1
<7> [123.058356] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [123.067081] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [123.067608] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [123.067852] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [123.068136] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [123.109666] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [123.127227] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.127238] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [123.127410] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [123.143351] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [123.143359] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [123.143537] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [123.144142] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] Same epoch counter 6
<7> [123.144502] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.144700] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.145224] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.145840] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [123.146009] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [123.146168] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [123.146802] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [123.147352] [IGT] i915_pm_rpm: exiting, ret=0
<7> [123.149114] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.149324] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.149821] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.150428] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [123.150620] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [123.150787] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [123.151408] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [123.151735] Console: switching to colour frame buffer device 128x48
<7> [123.152301] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [123.152495] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [123.152969] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [123.153648] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [123.153845] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [123.154026] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [123.154713] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2023-05-28 13:39:07