Results for igt@i915_module_load@load

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g766edf969 (x86_64) (Linux: 6.4.0-rc4-linus-v6.4-rc4-g7877cb91f108+ x86_64)
Out 
Starting subtest: load
Opened device: /dev/dri/card0
Subtest load: SUCCESS (1.351s)
Err 
Starting subtest: load
Subtest load: SUCCESS (1.351s)
Dmesg
<6> [43.536328] [IGT] i915_module_load: executing
<6> [43.795190] [IGT] i915_module_load: starting subtest load
<4> [44.285280]
<4> [44.285291] **********************************************************
<4> [44.285293] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
<4> [44.285296] ** **
<4> [44.285298] ** trace_printk() being used. Allocating extra memory. **
<4> [44.285300] ** **
<4> [44.285302] ** This means that this is a DEBUG kernel and it is **
<4> [44.285304] ** unsafe for production use. **
<4> [44.285306] ** **
<4> [44.285308] ** If you see this message and you are not debugging **
<4> [44.285310] ** the kernel, report this immediately to your vendor! **
<4> [44.285312] ** **
<4> [44.285314] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
<4> [44.285316] **********************************************************
<7> [44.349425] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K
<7> [44.349703] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [44.349903] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint LP PCH
<7> [44.350084] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [44.350458] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [44.350688] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 24000 kHz
<6> [44.351518] i915 0000:00:02.0: [drm] Found 64MB of eDRAM
<7> [44.351802] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [44.351965] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [44.352122] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [44.352258] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [44.352901] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [44.353384] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [44.353419] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 7ff00047
<7> [44.353719] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K
<7> [44.354333] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x7a9d1018
<7> [44.354829] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [44.355082] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [44.355330] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [44.355600] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [44.365180] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
<7> [44.365421] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [44.365617] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [44.365854] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [44.366026] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [44.366156] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X16, ranks: 1, 16Gb DIMMs: no
<7> [44.366327] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [44.366471] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no
<7> [44.366659] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X16, ranks: 1, 16Gb DIMMs: no
<7> [44.366781] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [44.366900] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no
<7> [44.367056] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [44.367180] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [44.367298] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [44.368029] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [44.368237] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 221
<7> [44.368428] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [44.368640] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 317, min size 5)
<7> [44.368874] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [44.369059] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [44.369246] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)
<7> [44.369428] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)
<7> [44.369647] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [44.369881] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)
<7> [44.370068] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [44.370254] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 22, min size 78)
<7> [44.370432] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0
<7> [44.370636] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [44.370839] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [44.371113] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [44.371381] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [44.371657] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [44.371878] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [44.372101] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [44.372280] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000
<7> [44.372479] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 LSPCON:1 USB-Type-C:0 TBT:0 DSC:0
<7> [44.372705] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 8
<7> [44.372883] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000
<7> [44.373060] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:1 TBT:0 DSC:0
<7> [44.373252] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8
<7> [44.373496] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000
<7> [44.373760] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02
<7> [44.374045] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [44.374393] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [44.374731] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
<7> [44.375005] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [44.375541] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz
<7> [44.375763] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz
<7> [44.375961] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [44.376237] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [44.376744] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [44.376964] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [44.377159] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<6> [44.377358] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
<7> [44.377628] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [44.377869] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [44.378050] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [44.378228] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [44.378482] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin
<7> [44.380022] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [44.380700] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV
<7> [44.380982] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us
<7> [44.381261] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [44.381526] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [44.381772] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [44.382021] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [44.382269] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [44.382513] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<6> [44.382657] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)
<7> [44.382731] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [44.382940] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [44.385254] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 3 display pipes available.
<7> [44.387579] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [44.388062] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind
<6> [44.388364] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
<7> [44.388672] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI A/PHY A] using AUX A (VBT)
<7> [44.388946] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:94:DDI A/PHY A]
<7> [44.391868] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [44.392079] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [44.392303] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [44.392529] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is static
<7> [44.392799] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [44.393036] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [44.393222] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [44.393402] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [44.393603] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [44.393833] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 0, level 255, controller 0
<7> [44.394013] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:1
<7> [44.394310] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:94:DDI A/PHY A] initial power sequencer: PPS 0
<7> [44.394655] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 0 t8 0 t9 0 t10 0 t11_t12 0
<7> [44.394905] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [44.395153] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [44.395396] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [44.395606] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [44.395867] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [44.396039] i915 0000:00:02.0: [drm:pps_vdd_init [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 VDD left on by BIOS, adjusting state tracking
<7> [44.407457] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.418460] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.429456] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.440456] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.451458] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.462455] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.473456] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.484458] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.495455] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.506457] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.517454] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.528461] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.539456] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.550454] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.561455] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.573461] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.584457] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.595460] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.606457] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.617458] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.628456] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.639461] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.650468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.661455] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.672457] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.683467] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.694456] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.705458] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.716455] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.727467] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.738455] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.749458] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d4002ff)
<7> [44.749683] i915 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110
<6> [44.749714] i915 0000:00:02.0: [drm] [ENCODER:94:DDI A/PHY A] failed to retrieve link info, disabling eDP
<7> [44.749783] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD off
<7> [44.749997] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [44.750222] i915 0000:00:02.0: [drm:intel_ddi_init [i915]] VBT says port B has lspcon
<7> [44.750411] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI B/PHY B] using AUX B (VBT)
<7> [44.750641] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:94:DDI B/PHY B]
<7> [44.751321] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [44.751540] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:107:DDI C/PHY C] using AUX C (VBT)
<7> [44.751763] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:107:DDI C/PHY C]
<7> [44.752283] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [44.752563] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:107:DDI C/PHY C]
<7> [44.752755] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:107:DDI C/PHY C] Using DDC pin 0x4 (VBT)
<7> [44.753058] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port D is not present
<7> [44.753240] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port E is not present
<7> [44.753896] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled
<7> [44.754131] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled
<7> [44.754337] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled
<7> [44.754548] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [44.754813] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A
<7> [44.755079] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A
<7> [44.755263] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B
<7> [44.755465] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B
<7> [44.755694] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B
<7> [44.755885] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C
<7> [44.756162] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C
<7> [44.756372] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C
<7> [44.756581] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [44.756795] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:96:DP-MST A] hw state readout: disabled, pipe A
<7> [44.756968] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:97:DP-MST B] hw state readout: disabled, pipe B
<7> [44.757187] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:98:DP-MST C] hw state readout: disabled, pipe C
<7> [44.757477] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:107:DDI C/PHY C] hw state readout: disabled, pipe A
<7> [44.757705] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:109:DP-MST A] hw state readout: disabled, pipe A
<7> [44.757879] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:110:DP-MST B] hw state readout: disabled, pipe B
<7> [44.758050] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:111:DP-MST C] hw state readout: disabled, pipe C
<7> [44.758234] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
<7> [44.758570] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [44.758848] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [44.759084] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [44.759376] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:DP-1] hw state readout: disabled
<7> [44.759603] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:108:DP-2] hw state readout: disabled
<7> [44.759842] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:114:HDMI-A-1] hw state readout: disabled
<7> [44.760062] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [44.760319] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz
<7> [44.760526] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz
<7> [44.760775] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [44.760961] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz
<7> [44.761157] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz
<7> [44.761344] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz
<7> [44.761593] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [44.761821] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz
<7> [44.762070] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz
<7> [44.762244] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz
<7> [44.762436] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [44.762779] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]
<7> [44.762984] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]
<7> [44.763236] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]
<7> [44.763420] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
<7> [44.763640] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [44.763879] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [44.764142] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [44.764787] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [44.764958] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [44.765114] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0
<7> [44.765311] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global
<7> [44.766891] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0
<7> [44.767088] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0
<7> [44.767264] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0
<7> [44.769144] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on bcs'0
<7> [44.770031] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'0
<7> [44.770798] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'1
<7> [44.771483] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vecs'0
<7> [44.784345] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV
<7> [44.784727] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping
<7> [44.784904] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping
<7> [44.785103] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping
<7> [44.785270] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [44.785495] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [44.786280] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [44.786437] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [44.786937] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [44.787119] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'1 to vcs1
<7> [44.787287] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [44.793912] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [44.796650] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [44.797547] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.799396] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.801059] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.802741] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.804467] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.805358] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: DP-HDMI ADAPTOR\004 (err 0)
<7> [44.805989] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.807421] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.809029] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.810873] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.812726] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.814347] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.815247] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode adaptor ID: a8 (err 0)
<7> [44.815268] i915 0000:00:02.0: [drm:lspcon_init [i915]] LSPCON detected
<7> [44.816821] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.818486] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.819861] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.821414] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.823331] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.824960] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.826824] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.828669] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.830313] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.831214] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [44.832282] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [44.833061] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [44.833086] i915 0000:00:02.0: [drm:lspcon_init [i915]] Vendor: Mega Chips
<7> [44.833351] i915 0000:00:02.0: [drm:lspcon_init [i915]] Success: LSPCON init
<7> [44.834279] i915 0000:00:02.0: [drm:lspcon_detect_hdr_capability [i915]] LSPCON capable of HDR
<7> [44.834572] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:DP-1] generating connector hotplug event
<7> [44.835732] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2
<7> [44.836851] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:108:DP-2] generating connector hotplug event
<7> [44.837607] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:114:HDMI-A-1] generating connector hotplug event
<6> [44.837713] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [44.841667] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected
<6> [44.865360] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [44.870596] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3
<7> [44.873121] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)
<7> [44.874247] [drm:drm_client_modeset_probe]
<7> [44.874180] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
<7> [44.874612] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [44.874514] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
<7> [44.874664] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [44.874791] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
<7> [44.875046] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
<7> [44.876002] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [44.876292] i915 device info: pciid=0x5926 rev=0x06 platform=KABYLAKE (subplatform=0x1) gen=9
<7> [44.876299] i915 device info: graphics version: 9
<7> [44.876303] i915 device info: media version: 9
<7> [44.876306] i915 device info: display version: 9
<7> [44.876310] i915 device info: graphics stepping: D1
<7> [44.876314] i915 device info: media stepping: D1
<7> [44.876317] i915 device info: display stepping: B1
<7> [44.876319] i915 device info: base die stepping: **
<7> [44.876322] i915 device info: gt: 3
<7> [44.876326] i915 device info: memory-regions: 0x21
<7> [44.876329] i915 device info: page-sizes: 0x11000
<7> [44.876333] i915 device info: platform: KABYLAKE
<7> [44.876337] i915 device info: ppgtt-size: 48
<7> [44.876341] i915 device info: ppgtt-type: 2
<7> [44.876344] i915 device info: dma_mask_size: 39
<7> [44.876347] i915 device info: is_mobile: no
<7> [44.876350] i915 device info: is_lp: no
<7> [44.876353] i915 device info: require_force_probe: no
<7> [44.876357] i915 device info: is_dgfx: no
<7> [44.876361] i915 device info: has_64bit_reloc: yes
<7> [44.876364] i915 device info: has_64k_pages: no
<7> [44.876368] i915 device info: gpu_reset_clobbers_display: no
<7> [44.876371] i915 device info: has_reset_engine: yes
<7> [44.876375] i915 device info: has_3d_pipeline: yes
<7> [44.876378] i915 device info: has_4tile: no
<7> [44.876382] i915 device info: has_flat_ccs: no
<7> [44.876385] i915 device info: has_global_mocs: no
<7> [44.876389] i915 device info: has_gmd_id: no
<7> [44.876392] i915 device info: has_gt_uc: yes
<7> [44.876396] i915 device info: has_heci_pxp: no
<7> [44.876399] i915 device info: has_heci_gscfi: no
<7> [44.876403] i915 device info: has_guc_deprivilege: no
<7> [44.876406] i915 device info: has_l3_ccs_read: no
<7> [44.876409] i915 device info: has_l3_dpf: no
<7> [44.876413] i915 device info: has_llc: yes
<7> [44.876416] i915 device info: has_logical_ring_contexts: yes
<7> [44.876420] i915 device info: has_logical_ring_elsq: no
<7> [44.876423] i915 device info: has_media_ratio_mode: no
<7> [44.876427] i915 device info: has_mslice_steering: no
<7> [44.876430] i915 device info: has_oa_bpc_reporting: no
<7> [44.876434] i915 device info: has_oa_slice_contrib_limits: no
<7> [44.876437] i915 device info: has_oam: no
<7> [44.876487] i915 device info: has_one_eu_per_fuse_bit: no
<7> [44.876491] i915 device info: has_pxp: no
<7> [44.876494] i915 device info: has_rc6: yes
<7> [44.876498] i915 device info: has_rc6p: no
<7> [44.876502] i915 device info: has_rps: yes
<7> [44.876505] i915 device info: has_runtime_pm: yes
<7> [44.876509] i915 device info: has_snoop: no
<7> [44.876512] i915 device info: has_coherent_ggtt: yes
<7> [44.876515] i915 device info: tuning_thread_rr_after_dep: no
<7> [44.876518] i915 device info: unfenced_needs_alignment: no
<7> [44.876521] i915 device info: hws_needs_physical: no
<7> [44.876525] i915 device info: has_pooled_eu: no
<7> [44.876528] i915 device info: cursor_needs_physical: no
<7> [44.876532] i915 device info: has_cdclk_crawl: no
<7> [44.876535] i915 device info: has_cdclk_squash: no
<7> [44.876539] i915 device info: has_ddi: yes
<7> [44.876542] i915 device info: has_dp_mst: yes
<7> [44.876545] i915 device info: has_dsb: no
<7> [44.876549] i915 device info: has_fpga_dbg: yes
<7> [44.876552] i915 device info: has_gmch: no
<7> [44.876555] i915 device info: has_hotplug: yes
<7> [44.876558] i915 device info: has_hti: no
<7> [44.876561] i915 device info: has_ipc: yes
<7> [44.876565] i915 device info: has_overlay: no
<7> [44.876567] i915 device info: has_psr: yes
<7> [44.876570] i915 device info: has_psr_hw_tracking: yes
<7> [44.876572] i915 device info: overlay_needs_physical: no
<7> [44.876575] i915 device info: supports_tv: no
<7> [44.876579] i915 device info: has_hdcp: yes
<7> [44.876582] i915 device info: has_dmc: yes
<7> [44.876586] i915 device info: has_dsc: no
<7> [44.876589] i915 device info: rawclk rate: 24000 kHz
<7> [44.876593] i915 device info: iommu: enabled
<7> [44.876597] i915 device info: available engines: 40c03
<7> [44.876601] i915 device info: slice total: 2, mask=0003
<7> [44.876605] i915 device info: subslice total: 6
<7> [44.876609] i915 device info: slice0: 3 subslices, mask=00000007
<7> [44.876612] i915 device info: slice1: 3 subslices, mask=00000007
<7> [44.876616] i915 device info: slice2: 0 subslices, mask=00000000
<7> [44.876619] i915 device info: EU total: 48
<7> [44.876623] i915 device info: EU per subslice: 8
<7> [44.876626] i915 device info: has slice power gating: yes
<7> [44.876629] i915 device info: has subslice power gating: no
<7> [44.876633] i915 device info: has EU power gating: yes
<6> [44.876637] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [44.876641] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [44.876645] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [44.876748] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [44.877113] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [44.880530] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.882250] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.883771] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.885740] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.887531] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.889162] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.891011] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.892715] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.894295] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [44.895350] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [44.896261] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [44.897120] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [44.897675] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [44.898296] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [44.898726] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [44.899000] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [44.899763] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [44.900492] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] status updated from unknown to disconnected
<7> [44.900767] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [44.901928] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2]
<7> [44.901959] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [44.902350] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [44.903086] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [44.903384] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] status updated from unknown to disconnected
<7> [44.903424] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected
<7> [44.903804] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1]
<7> [44.903834] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [44.904186] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [44.957515] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [44.974043] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [44.974052] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [44.974242] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [44.990645] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [44.990656] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [44.990840] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [44.991042] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] status updated from unknown to disconnected
<7> [44.991074] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [44.991096] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [44.991111] [drm:drm_client_modeset_probe] connector 95 enabled? no
<7> [44.991115] [drm:drm_client_modeset_probe] connector 108 enabled? no
<7> [44.991118] [drm:drm_client_modeset_probe] connector 114 enabled? no
<7> [44.991299] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [44.991326] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [44.991352] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [44.991382] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [44.992467] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [44.992691] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [44.993220] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [44.993909] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [44.994107] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [44.994291] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [44.994961] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [44.995358] [drm:drm_client_modeset_probe]
<7> [44.995650] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [44.995695] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [44.996092] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [44.996849] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [44.997493] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [44.998088] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [44.999478] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [44.999686] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [45.000605] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.002650] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.004313] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.005939] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.010284] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.012185] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.014047] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.015912] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.017827] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.018889] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [45.020034] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [45.020638] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [45.021196] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [45.021890] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [45.022151] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [45.022377] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [45.023261] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [45.023682] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [45.023713] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2]
<7> [45.023733] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [45.023974] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [45.024731] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [45.024948] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected
<7> [45.024968] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1]
<7> [45.024988] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [45.025223] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [45.077487] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [45.096545] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [45.096558] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [45.096822] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<6> [45.097451] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380
<6> [45.098501] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002)
<7> [45.112242] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [45.114425] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [45.114436] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [45.114861] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [45.115122] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [45.115150] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [45.115168] [drm:drm_client_modeset_probe] connector 95 enabled? no
<7> [45.115174] [drm:drm_client_modeset_probe] connector 108 enabled? no
<7> [45.115180] [drm:drm_client_modeset_probe] connector 114 enabled? no
<7> [45.115353] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [45.115379] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [45.115422] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [45.115694] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<6> [45.115644] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [45.115842] [drm:drm_client_modeset_probe]
<7> [45.115904] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [45.115932] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [45.116104] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [45.116303] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [45.116867] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [45.117436] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [45.117658] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [45.120063] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [45.123429] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [45.125476] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [45.125832] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [45.127677] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.129134] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.130875] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.133105] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.136976] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.138893] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.140750] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.142529] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.144129] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [45.145041] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [45.146188] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<6> [45.146915] [IGT] i915_module_load: exiting, ret=0
<7> [45.147047] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [45.147649] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [45.147683] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2]
<7> [45.147706] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [45.147966] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected
<7> [45.147994] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1]
<7> [45.148010] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<6> [45.161770] i915_module_loa (840) used greatest stack depth: 11848 bytes left
Created at 2023-05-28 13:39:07