igt@i915_module_load@reload on bat-jsl-3@linus-v6.4-rc4 Test details

Detail	Value
Igt-Version	IGT-Version: 1.27.1-g766edf969 (x86_64) (Linux: 6.4.0-rc4-linus-v6.4-rc4-g7877cb91f108+ x86_64)
Out	Starting subtest: reload Opened device: /dev/dri/card0 Subtest reload: SUCCESS (3.469s)
Err	Starting subtest: reload Subtest reload: SUCCESS (3.469s)
Dmesg	<6> [348.401099] Console: switching to colour dummy device 80x25 <6> [348.402163] [IGT] i915_module_load: executing <6> [348.416215] [IGT] i915_module_load: starting subtest reload <7> [348.677903] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind <7> [348.750733] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [348.751534] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [348.752336] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [348.753092] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [348.753849] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [348.754614] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [348.755348] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [348.756051] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [348.756787] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [348.757334] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [348.758296] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4 <7> [348.763318] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.enable (expected 1, found 0) <7> [348.763678] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.active (expected 1, found 0) <7> [348.763991] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in cpu_transcoder (expected 4, found -1) <7> [348.764413] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in lane_count (expected 4, found 0) <7> [348.764717] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in dp_m_n (expected tu 64 data 4209566/8388608 link 350797/524288, found tu 0, data 0/0 link 0/0) <7> [348.765019] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in output_types (expected 0x00000100, found 0x00000000) <7> [348.765410] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in framestart_delay (expected 1, found 0) <7> [348.765707] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0) <7> [348.766001] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_htotal (expected 3316, found 0) <7> [348.766325] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0) <7> [348.766631] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_end (expected 3316, found 0) <7> [348.766913] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0) <7> [348.767192] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0) <7> [348.767499] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0) <7> [348.767788] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vtotal (expected 1816, found 0) <7> [348.768073] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0) <7> [348.768369] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_end (expected 1816, found 0) <7> [348.768654] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_start (expected 1802, found 0) <7> [348.768944] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_end (expected 1807, found 0) <7> [348.769260] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0) <7> [348.769566] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_htotal (expected 3316, found 0) <7> [348.769843] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0) <7> [348.770125] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_end (expected 3316, found 0) <7> [348.770423] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0) <7> [348.770704] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0) <7> [348.770989] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0) <7> [348.771299] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vtotal (expected 1816, found 0) <7> [348.771612] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0) <7> [348.771899] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_end (expected 1816, found 0) <7> [348.772182] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_start (expected 1802, found 0) <7> [348.772480] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_end (expected 1807, found 0) <7> [348.772768] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in pixel_multiplier (expected 1, found 0) <7> [348.773044] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.flags (2) (expected 2, found 0) <7> [348.773333] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.flags (8) (expected 8, found 0) <7> [348.773623] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in pipe_bpp (expected 24, found 0) <7> [348.773919] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_clock (expected 361310, found 0) <7> [348.774218] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_clock (expected 361310, found 0) <7> [348.774535] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in port_clock (expected 540000, found 0) <7> [348.774829] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll.isra.0 [i915]] [CRTC:98:pipe A] releasing DPLL 0 <7> [348.775174] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 1024) -> (0 - 0), active pipes 0x1 -> 0x0 <7> [348.775578] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0 <7> [348.775852] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 985 - 1024) -> ( 0 - 0), size 39 -> 0 <7> [348.776120] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [348.776426] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [348.776723] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [348.777003] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [348.777300] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0 <7> [348.777593] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0 <7> [348.777875] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0 <7> [348.778147] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0 <7> [348.778537] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change <7> [348.778834] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz <7> [348.779124] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0 <7> [348.779441] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [modeset] <7> [348.779727] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no <7> [348.780009] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [348.780308] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [348.780589] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [348.780861] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [348.781149] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no <7> [348.781476] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no <7> [348.781772] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no <7> [348.791152] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]] <7> [348.996652] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 0 <7> [348.997761] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A <7> [349.005432] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on <7> [349.006216] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7> [349.007342] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power off <7> [349.008020] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power off time <7> [349.008750] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7> [349.012854] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [349.013312] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [349.013862] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [349.014585] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [349.034070] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [349.034301] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [349.034583] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 20 <7> [349.034902] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [349.061341] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [349.061857] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A <7> [349.062413] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:98:pipe A] <7> [349.062990] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0 <7> [349.063104] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [349.063435] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [349.063481] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [349.063932] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 30 <7> [349.063977] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A] <7> [349.064486] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [349.064491] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0 <7> [349.065159] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A] <7> [349.065699] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B] <7> [349.066165] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A] <7> [349.066680] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B] <7> [349.067027] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C] <7> [349.067385] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C] <7> [349.067736] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1] <7> [349.068128] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [349.068551] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [349.068928] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4 <7> [349.069768] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A] <7> [349.100217] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915] <7> [349.177576] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper <7> [349.178845] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [349.668938] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [349.669762] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [350.906944] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K <7> [350.907460] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no) <7> [350.907842] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH <7> [350.908200] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [350.908767] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [350.909202] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 19200 kHz <7> [350.910218] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001 <7> [350.910534] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001 <7> [350.911434] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [350.911730] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [350.912007] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M <6> [350.912310] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [350.912320] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [350.912917] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [350.912953] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7 <7> [350.913301] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K <7> [350.914001] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018 <7> [350.914411] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0 <7> [350.914746] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [350.915070] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x <7> [350.915409] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported <7> [350.923313] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583 <7> [350.923707] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [350.924030] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [350.924387] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4) <7> [350.924757] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4 <7> [350.925080] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no <7> [350.925399] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [350.925688] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no <7> [350.925969] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no <7> [350.926262] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [350.926540] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no <7> [350.926800] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes <7> [350.927168] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [350.927493] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no <7> [350.927790] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50 <7> [350.928169] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68 <7> [350.928539] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56 <7> [350.928889] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834 <7> [350.929225] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941 <7> [350.929572] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878 <7> [350.929922] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899 <7> [350.930306] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488 <7> [350.930665] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583 <7> [350.931009] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069 <7> [350.931367] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719 <7> [350.931704] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483 <7> [350.932035] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280 <7> [350.932423] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000 <7> [350.932779] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000 <7> [350.933126] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000 <7> [350.933485] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000 <7> [350.933824] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000 <7> [350.934149] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000 <7> [350.934500] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000 <7> [350.934865] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000 <7> [350.935883] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [350.936273] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228 <7> [350.936632] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7) <7> [350.936977] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5) <7> [350.937334] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100) <7> [350.937694] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [350.938062] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812) <7> [350.938478] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34) <7> [350.938829] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [350.939174] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366) <7> [350.939529] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305) <7> [350.939876] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78) <7> [350.940261] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822) <7> [350.940621] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0 <7> [350.940958] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [350.941307] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806 <7> [350.941652] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6 <7> [350.941981] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [350.942391] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [350.942743] i915 0000:00:02.0: [drm:intel_bios_init [i915]] port C trying to use the same DDC pin (0x3) as port A, disabling port A DVI/HDMI support <7> [350.943085] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [350.943435] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0 <7> [350.943769] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000 <7> [350.944089] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [350.944428] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0 <7> [350.944769] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000 <7> [350.945122] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [350.945488] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0 <7> [350.945823] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000 <7> [350.946160] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a <7> [350.946581] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [350.946956] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [350.947325] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [350.947692] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [350.948061] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [350.948422] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [350.948779] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [350.949203] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [350.949617] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0 <7> [350.949985] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [350.950560] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [350.950906] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [350.951258] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [350.951636] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [350.951985] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [350.952357] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [350.952725] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [350.953074] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [350.953439] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [350.953776] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [350.954114] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [350.954659] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4 <7> [350.955151] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin <7> [350.956877] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <6> [350.957801] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9) <7> [350.957939] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us <7> [350.958342] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec) <7> [350.958680] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec) <7> [350.959007] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec) <7> [350.959373] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec) <7> [350.959729] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec) <7> [350.960062] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec) <7> [350.960417] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec) <7> [350.960744] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec) <7> [350.972673] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 3 display pipes available. <7> [350.978720] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0 <7> [350.979284] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz <7> [350.979663] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] Max dotclock rate: 1113600 kHz <7> [350.980075] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] using AUX A (VBT) <7> [350.980474] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A] <7> [350.984398] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0) <7> [350.984825] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2 <7> [350.985190] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2 <7> [350.985600] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless <7> [350.985974] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7> [350.986342] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300 <7> [350.986692] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002 <7> [350.987046] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName <7> [350.987442] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz <7> [350.987803] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0 <7> [350.988274] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0 <7> [350.988703] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000 <7> [350.989042] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [350.989386] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [350.989734] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [350.990082] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [350.990554] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7> [350.991053] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [350.991643] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on <7> [350.992022] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [350.992475] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [350.992825] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [350.993221] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068 <7> [350.993571] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled <7> [351.197777] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00 <7> [351.198747] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001 <7> [351.199538] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6 <7> [351.200496] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1 <7> [351.205854] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [351.207787] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [351.209633] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [351.211581] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [351.213592] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [351.215534] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [351.217283] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [351.218897] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [351.220356] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [351.220372] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [351.220380] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [351.220478] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [351.220872] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa <7> [351.221205] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms) <7> [351.233873] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none <7> [351.234418] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0) <7> [351.234801] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, disabled, brightness 0/96000 <7> [351.235226] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000 <7> [351.235582] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [351.236154] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [351.236526] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [351.237003] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [351.237461] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7> [351.238517] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] using AUX B (VBT) <7> [351.238922] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B] <7> [351.239678] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported <7> [351.240035] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B] <7> [351.240370] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT) <7> [351.240940] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:262:DDI C (TC)/PHY C] using AUX C (platform default) <7> [351.241402] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C] <7> [351.241733] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT) <7> [351.242167] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port D is not present <7> [351.243366] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled <7> [351.243881] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled <7> [351.244362] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled <7> [351.244712] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A <7> [351.245073] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A <7> [351.245468] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A <7> [351.245834] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A <7> [351.246178] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A <7> [351.246541] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A <7> [351.246886] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A <7> [351.247267] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A <7> [351.247641] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B <7> [351.247988] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B <7> [351.248396] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B <7> [351.248739] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B <7> [351.249080] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B <7> [351.249466] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B <7> [351.249836] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B <7> [351.250177] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B <7> [351.250546] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C <7> [351.250895] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C <7> [351.251227] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C <7> [351.251592] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C <7> [351.251966] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C <7> [351.252346] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C <7> [351.252697] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C <7> [351.253039] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C <7> [351.253397] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A <7> [351.253760] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A <7> [351.254117] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A <7> [351.254497] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B <7> [351.254837] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C <7> [351.255187] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A <7> [351.255547] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0 <7> [351.255903] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [351.256369] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0 <7> [351.256821] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled <7> [351.257181] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled <7> [351.257555] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled <7> [351.257908] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled <7> [351.258446] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz <7> [351.258799] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz <7> [351.259127] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz <7> [351.259599] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz <7> [351.259928] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz <7> [351.260263] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz <7> [351.260591] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz <7> [351.260926] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz <7> [351.261293] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0 <7> [351.261669] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz <7> [351.261995] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz <7> [351.262336] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz <7> [351.262662] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz <7> [351.262983] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz <7> [351.263386] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz <7> [351.263732] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz <7> [351.264061] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz <7> [351.264407] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [351.264757] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz <7> [351.265077] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz <7> [351.265435] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz <7> [351.265795] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz <7> [351.266126] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz <7> [351.266478] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz <7> [351.266805] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz <7> [351.267118] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz <7> [351.267461] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [351.288940] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state] <7> [351.289360] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state] <7> [351.289705] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state] <7> [351.290050] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [351.290416] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [351.290784] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [351.291450] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture <7> [351.291767] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000] <7> [351.292085] MCR Steering: Default steering: group=0x0, instance=0x0 <7> [351.292111] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global <7> [351.294771] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0 <7> [351.295163] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0 <7> [351.295567] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0 <7> [351.298168] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0 <7> [351.299092] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0 <7> [351.300630] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0 <7> [351.316850] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping <7> [351.317274] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping <7> [351.317614] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping <7> [351.317941] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config <7> [351.318327] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [351.319932] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0 <7> [351.320287] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0 <7> [351.320577] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0 <7> [351.320868] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0 <7> [351.328021] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered <7> [351.328640] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1 <7> [351.330742] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event <7> [351.331690] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1 <7> [351.333213] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event <7> [351.333932] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event <7> [351.334822] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event <6> [351.334940] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 <7> [351.338759] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected <6> [351.379658] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [351.387359] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input14 <6> [351.388351] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0) <7> [351.391313] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x810 (init value 0x810) <7> [351.392454] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4 <7> [351.393825] [drm:intel_dsm_detect [i915]] no _DSM method for intel device <7> [351.394207] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11 <7> [351.394215] i915 device info: graphics version: 11 <7> [351.394219] i915 device info: media version: 11 <7> [351.394222] i915 device info: display version: 11 <7> [351.394226] i915 device info: graphics stepping: B0 <7> [351.394230] i915 device info: media stepping: B0 <7> [351.394233] i915 device info: display stepping: B0 <7> [351.394237] i915 device info: base die stepping: * <7> [351.394255] i915 device info: gt: 0 <7> [351.394260] i915 device info: memory-regions: 0x21 <7> [351.394263] i915 device info: page-sizes: 0x211000 <7> [351.394267] i915 device info: platform: JASPERLAKE <7> [351.394271] i915 device info: ppgtt-size: 36 <7> [351.394274] i915 device info: ppgtt-type: 2 <7> [351.394278] i915 device info: dma_mask_size: 39 <7> [351.394281] i915 device info: is_mobile: no <7> [351.394285] i915 device info: is_lp: no <7> [351.394288] i915 device info: require_force_probe: no <7> [351.394292] i915 device info: is_dgfx: no <7> [351.394295] i915 device info: has_64bit_reloc: yes <7> [351.394299] i915 device info: has_64k_pages: no <7> [351.394302] i915 device info: gpu_reset_clobbers_display: no <7> [351.394306] i915 device info: has_reset_engine: yes <7> [351.394309] i915 device info: has_3d_pipeline: yes <7> [351.394313] i915 device info: has_4tile: no <7> [351.394317] i915 device info: has_flat_ccs: no <7> [351.394320] i915 device info: has_global_mocs: no <7> [351.394324] i915 device info: has_gmd_id: no <7> [351.394327] i915 device info: has_gt_uc: yes <7> [351.394331] i915 device info: has_heci_pxp: no <7> [351.394334] i915 device info: has_heci_gscfi: no <7> [351.394337] i915 device info: has_guc_deprivilege: no <7> [351.394341] i915 device info: has_l3_ccs_read: no <7> [351.394345] i915 device info: has_l3_dpf: no <7> [351.394348] i915 device info: has_llc: yes <7> [351.394351] i915 device info: has_logical_ring_contexts: yes <7> [351.394355] i915 device info: has_logical_ring_elsq: yes <7> [351.394358] i915 device info: has_media_ratio_mode: no <7> [351.394362] i915 device info: has_mslice_steering: no <7> [351.394365] i915 device info: has_oa_bpc_reporting: no <7> [351.394369] i915 device info: has_oa_slice_contrib_limits: no <7> [351.394373] i915 device info: has_oam: no <7> [351.394376] i915 device info: has_one_eu_per_fuse_bit: no <7> [351.394379] i915 device info: has_pxp: no <7> [351.394383] i915 device info: has_rc6: yes <7> [351.394386] i915 device info: has_rc6p: no <7> [351.394389] i915 device info: has_rps: yes <7> [351.394392] i915 device info: has_runtime_pm: yes <7> [351.394396] i915 device info: has_snoop: no <7> [351.394391] [drm:drm_client_modeset_probe] <7> [351.394401] i915 device info: has_coherent_ggtt: no <7> [351.394404] i915 device info: tuning_thread_rr_after_dep: no <7> [351.394407] i915 device info: unfenced_needs_alignment: no <7> [351.394411] i915 device info: hws_needs_physical: no <7> [351.394414] i915 device info: has_pooled_eu: no <7> [351.394417] i915 device info: cursor_needs_physical: no <7> [351.394421] i915 device info: has_cdclk_crawl: no <7> [351.394424] i915 device info: has_cdclk_squash: no <7> [351.394427] i915 device info: has_ddi: yes <7> [351.394431] i915 device info: has_dp_mst: yes <7> [351.394434] i915 device info: has_dsb: no <7> [351.394437] i915 device info: has_fpga_dbg: yes <7> [351.394441] i915 device info: has_gmch: no <7> [351.394444] i915 device info: has_hotplug: yes <7> [351.394448] i915 device info: has_hti: no <7> [351.394451] i915 device info: has_ipc: yes <7> [351.394454] i915 device info: has_overlay: no <7> [351.394457] i915 device info: has_psr: yes <7> [351.394461] i915 device info: has_psr_hw_tracking: yes <7> [351.394464] i915 device info: overlay_needs_physical: no <7> [351.394467] i915 device info: supports_tv: no <7> [351.394471] i915 device info: has_hdcp: no <7> [351.394474] i915 device info: has_dmc: yes <7> [351.394478] i915 device info: has_dsc: yes <7> [351.394481] i915 device info: rawclk rate: 19200 kHz <7> [351.394485] i915 device info: iommu: enabled <7> [351.394489] i915 device info: available engines: 40403 <7> [351.394493] i915 device info: slice total: 1, mask=0001 <7> [351.394497] i915 device info: subslice total: 4 <7> [351.394501] i915 device info: slice0: 4 subslices, mask=0000000f <7> [351.394506] i915 device info: EU total: 16 <7> [351.394509] i915 device info: EU per subslice: 4 <7> [351.394512] i915 device info: has slice power gating: yes <7> [351.394516] i915 device info: has subslice power gating: yes <7> [351.394519] i915 device info: has EU power gating: yes <6> [351.394524] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [351.394528] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [351.394531] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [351.395007] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] <7> [351.395100] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [351.397612] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [351.398025] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [351.398629] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [351.398977] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [351.399615] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [351.399629] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [351.399638] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [351.399721] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [351.400081] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [351.403992] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [351.404509] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [351.405716] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [351.406642] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [351.407445] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] status updated from unknown to connected <7> [351.408872] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes : <7> [351.408921] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [351.408934] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa <7> [351.408945] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] <7> [351.408980] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [351.409672] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] status updated from unknown to disconnected <7> [351.409721] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected <7> [351.409765] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] <7> [351.409797] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [351.410224] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected <7> [351.410292] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected <7> [351.410333] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] <7> [351.410365] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [351.410783] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected <7> [351.410828] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected <7> [351.410866] [drm:drm_client_modeset_probe] connector 239 enabled? yes <7> [351.410876] [drm:drm_client_modeset_probe] connector 248 enabled? no <7> [351.410882] [drm:drm_client_modeset_probe] connector 257 enabled? no <7> [351.410887] [drm:drm_client_modeset_probe] connector 263 enabled? no <7> [351.411184] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [351.411236] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239 <7> [351.411268] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0 <7> [351.411274] [drm:drm_client_modeset_probe] found mode 3200x1800 <7> [351.411280] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [351.411302] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0) <7> [351.411504] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <7> [351.411631] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one <7> [351.430975] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x00180000 <6> [351.435798] fbcon: i915drmfb (fb0) is primary device <7> [351.439717] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36) <7> [351.440187] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz <7> [351.440631] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24 <7> [351.440987] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000 <7> [351.441464] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no <7> [351.441836] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long <7> [351.442188] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0 <7> [351.442588] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A] <6> [351.442872] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0) <7> [351.442936] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.enable (expected 0, found 1) <7> [351.443314] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.active (expected 0, found 1) <7> [351.443687] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in cpu_transcoder (expected -1, found 4) <7> [351.444059] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in lane_count (expected 0, found 4) <7> [351.444453] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4209566/8388608 link 350797/524288) <7> [351.444815] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in output_types (expected 0x00000000, found 0x00000100) <7> [351.445165] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in framestart_delay (expected 0, found 1) <7> [351.445560] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200) <7> [351.445908] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_htotal (expected 0, found 3316) <7> [351.446283] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200) <7> [351.446636] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_end (expected 0, found 3316) <7> [351.446994] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248) <7> [351.447408] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280) <7> [351.447771] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800) <7> [351.448132] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vtotal (expected 0, found 1816) <7> [351.448529] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800) <7> [351.448906] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_end (expected 0, found 1816) <7> [351.449298] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_start (expected 0, found 1802) <7> [351.449646] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_end (expected 0, found 1807) <7> [351.449991] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200) <7> [351.450499] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_htotal (expected 0, found 3316) <7> [351.450854] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200) <7> [351.451202] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3316) <7> [351.451579] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248) <7> [351.451930] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280) <7> [351.452305] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800) <7> [351.452660] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vtotal (expected 0, found 1816) <7> [351.453015] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800) <7> [351.453385] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1816) <7> [351.453722] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1802) <7> [351.454064] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1807) <7> [351.454439] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in pixel_multiplier (expected 0, found 1) <7> [351.454807] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.flags (2) (expected 0, found 2) <7> [351.455190] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.flags (8) (expected 0, found 8) <7> [351.455610] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x0000004b) <7> [351.455961] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in dpll_hw_state.cfgcr0 (expected 0x00000000, found 0x01c001a5) <7> [351.456339] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in pipe_bpp (expected 0, found 24) <7> [351.456789] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_clock (expected 0, found 361310) <7> [351.457129] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_clock (expected 0, found 361310) <7> [351.457510] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in port_clock (expected 0, found 540000) <7> [351.457939] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 1024), active pipes 0x0 -> 0x1 <7> [351.458352] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985 <7> [351.458694] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39 <7> [351.459051] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,*twm, swm, stwm <7> [351.459421] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 <7> [351.459772] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 <7> [351.460145] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 <7> [351.460561] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1 <7> [351.460928] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446 <7> [351.461293] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446 <7> [351.461739] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446 <7> [351.462118] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (180655 kHz) > [CRTC:98:pipe A] min cdclk (0 kHz) <7> [351.462503] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz) <7> [351.462872] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change <7> [351.463216] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz <7> [351.463599] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1 <7> [351.463978] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0 <7> [351.464358] i915 0000:00:02.0: [drm:intel_reference_shared_dpll.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0 <7> [351.464713] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset] <7> [351.465056] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB <7> [351.465419] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0 <7> [351.465782] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [351.466117] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [351.466479] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [351.466823] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [351.467163] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64 <7> [351.467536] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [351.467895] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [351.468268] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7> [351.468637] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2 <7> [351.469004] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [351.469509] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [351.469854] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [351.470392] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa <7> [351.470736] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [351.471073] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310 <7> [351.471502] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0 <7> [351.471874] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [351.472238] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [351.472724] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [351.473068] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [351.473495] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [351.473839] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [351.474180] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:240] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [351.474620] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [351.474971] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0 <7> [351.475393] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [351.475729] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [351.476063] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [351.476508] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [351.476849] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no <7> [351.477187] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no <7> [351.477606] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no <7> [351.479315] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1 <7> [351.480226] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A] <7> [351.480799] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B] <7> [351.481186] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A] <7> [351.481612] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B] <7> [351.481950] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C] <7> [351.482517] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C] <7> [351.482960] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [351.483775] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [351.484194] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4 <7> [351.485104] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A] <7> [351.485754] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0 <7> [351.487547] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on <7> [351.488101] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [351.488830] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068 <7> [351.489203] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [351.489770] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on <7> [351.490178] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000006b <7> [351.702342] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [351.702783] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [351.705785] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00 <7> [351.705850] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [ENCODER:238:DDI A/PHY A] Using LINK_BW_SET value 14 <7> [351.706891] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7> [351.707418] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7> [351.709029] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0 <7> [351.709393] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0 <7> [351.711031] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK <7> [351.711377] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3 <7> [351.713466] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1 <7> [351.713801] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1 <7> [351.715916] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7> [351.716314] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4 <7> [351.717088] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A <7> [351.718003] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]] <7> [351.718401] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A <7> [351.718959] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000 <7> [351.724419] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1 <7> [351.724834] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A] <7> [351.735364] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1] <7> [351.735814] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A] <7> [351.736735] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0 <7> [351.737135] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp <7> [351.737586] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <6> [351.739026] Console: switching to colour frame buffer device 400x112 <6> [351.760904] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device <7> [351.768774] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]] <7> [351.768875] [drm:drm_client_modeset_probe] <7> [351.769365] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] <7> [351.769455] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [351.771424] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [351.771738] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [351.772019] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [351.772328] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [351.772924] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [351.772937] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [351.772944] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [351.773001] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [351.773321] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [351.774721] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [351.775005] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [351.776649] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes : <7> [351.776696] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [351.776707] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa <7> [351.776716] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] <7> [351.776747] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [351.777215] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected <7> [351.777266] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] <7> [351.777295] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [351.777623] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected <7> [351.777653] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] <7> [351.777681] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [351.778005] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected <7> [351.778034] [drm:drm_client_modeset_probe] connector 239 enabled? yes <7> [351.778042] [drm:drm_client_modeset_probe] connector 248 enabled? no <7> [351.778046] [drm:drm_client_modeset_probe] connector 257 enabled? no <7> [351.778049] [drm:drm_client_modeset_probe] connector 263 enabled? no <7> [351.778329] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [351.778384] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239 <7> [351.778390] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0 <7> [351.778394] [drm:drm_client_modeset_probe] found mode 3200x1800 <7> [351.778398] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config <7> [351.778459] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0) <7> [351.785426] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]] <7> [351.785491] [drm:drm_client_modeset_probe] <7> [351.785572] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] <7> [351.785627] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [351.790151] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [351.790740] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [351.791056] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [351.791677] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [351.792917] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [351.792937] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [351.792945] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [351.792986] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [351.793840] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [351.796206] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [351.796630] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [351.798073] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes : <7> [351.798113] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [351.798126] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa <7> [351.798137] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] <7> [351.798171] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [351.798646] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected <7> [351.798683] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] <7> [351.798714] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [351.799049] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected <7> [351.799084] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] <7> [351.799115] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [351.799789] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected <7> [351.799823] [drm:drm_client_modeset_probe] connector 239 enabled? yes <7> [351.799833] [drm:drm_client_modeset_probe] connector 248 enabled? no <7> [351.799838] [drm:drm_client_modeset_probe] connector 257 enabled? no <7> [351.799844] [drm:drm_client_modeset_probe] connector 263 enabled? no <7> [351.799917] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [351.799937] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239 <7> [351.799944] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0 <7> [351.799950] [drm:drm_client_modeset_probe] found mode 3200x1800 <7> [351.799955] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config <7> [351.799983] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0) <6> [351.801191] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100 <6> [351.808116] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0) <6> [351.820142] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) <7> [351.820602] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [351.821210] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [351.822175] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x810 <7> [351.839743] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [351.841536] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [351.851826] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <6> [351.885877] [IGT] i915_module_load: exiting, ret=0

<7> [348.677903] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind

<7> [348.750733] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [348.751534] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [348.752336] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [348.753092] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [348.753849] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [348.754614] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [348.755348] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [348.756051] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [348.756787] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [348.757334] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<7> [348.758296] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4

<7> [348.763318] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.enable (expected 1, found 0)

<7> [348.763678] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.active (expected 1, found 0)

<7> [348.763991] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in cpu_transcoder (expected 4, found -1)

<7> [348.764413] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in lane_count (expected 4, found 0)

<7> [348.764717] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in dp_m_n (expected tu 64 data 4209566/8388608 link 350797/524288, found tu 0, data 0/0 link 0/0)

<7> [348.765019] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in output_types (expected 0x00000100, found 0x00000000)

<7> [348.765410] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in framestart_delay (expected 1, found 0)

<7> [348.765707] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0)

<7> [348.766001] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_htotal (expected 3316, found 0)

<7> [348.766325] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0)

<7> [348.766631] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_end (expected 3316, found 0)

<7> [348.766913] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0)

<7> [348.767192] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0)

<7> [348.767499] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)

<7> [348.767788] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vtotal (expected 1816, found 0)

<7> [348.768073] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)

<7> [348.768369] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_end (expected 1816, found 0)

<7> [348.768654] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_start (expected 1802, found 0)

<7> [348.768944] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_end (expected 1807, found 0)

<7> [348.769260] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0)

<7> [348.769566] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_htotal (expected 3316, found 0)

<7> [348.769843] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0)

<7> [348.770125] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_end (expected 3316, found 0)

<7> [348.770423] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0)

<7> [348.770704] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0)

<7> [348.770989] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)

<7> [348.771299] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vtotal (expected 1816, found 0)

<7> [348.771612] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)

<7> [348.771899] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_end (expected 1816, found 0)

<7> [348.772182] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_start (expected 1802, found 0)

<7> [348.772480] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_end (expected 1807, found 0)

<7> [348.772768] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in pixel_multiplier (expected 1, found 0)

<7> [348.773044] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.flags (2) (expected 2, found 0)

<7> [348.773333] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.flags (8) (expected 8, found 0)

<7> [348.773623] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in pipe_bpp (expected 24, found 0)

<7> [348.773919] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_clock (expected 361310, found 0)

<7> [348.774218] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_clock (expected 361310, found 0)

<7> [348.774535] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in port_clock (expected 540000, found 0)

<7> [348.774829] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll.isra.0 [i915]] [CRTC:98:pipe A] releasing DPLL 0

<7> [348.775174] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 1024) -> (0 - 0), active pipes 0x1 -> 0x0

<7> [348.775578] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0

<7> [348.775852] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 985 - 1024) -> ( 0 - 0), size 39 -> 0

<7> [348.776120] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [348.776426] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [348.776723] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [348.777003] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [348.777300] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0

<7> [348.777593] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0

<7> [348.777875] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0

<7> [348.778147] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0

<7> [348.778537] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change

<7> [348.778834] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz

<7> [348.779124] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0

<7> [348.779441] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [modeset]

<7> [348.779727] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no

<7> [348.780009] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [348.780308] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [348.780589] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [348.780861] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [348.781149] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no

<7> [348.781476] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no

<7> [348.781772] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no

<7> [348.791152] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]

<7> [348.996652] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 0

<7> [348.997761] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A

<7> [349.005432] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on

<7> [349.006216] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b

<7> [349.007342] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power off

<7> [349.008020] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power off time

<7> [349.008750] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060

<7> [349.012854] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [349.013312] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [349.013862] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [349.014585] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [349.034070] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [349.034301] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [349.034583] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 20

<7> [349.034902] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [349.061341] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [349.061857] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A

<7> [349.062413] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:98:pipe A]

<7> [349.062990] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0

<7> [349.063104] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [349.063435] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [349.063481] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [349.063932] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 30

<7> [349.063977] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]

<7> [349.064486] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [349.064491] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0

<7> [349.065159] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]

<7> [349.065699] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]

<7> [349.066165] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]

<7> [349.066680] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]

<7> [349.067027] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]

<7> [349.067385] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]

<7> [349.067736] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]

<7> [349.068128] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [349.068551] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [349.068928] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4

<7> [349.069768] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]

<7> [349.100217] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]

<7> [349.177576] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper

<7> [349.178845] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [349.668938] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [349.669762] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [350.906944] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K

<7> [350.907460] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)

<7> [350.907842] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH

<7> [350.908200] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [350.908767] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [350.909202] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 19200 kHz

<7> [350.910218] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001

<7> [350.910534] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001

<7> [350.911434] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [350.911730] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [350.912007] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M

<6> [350.912310] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [350.912917] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [350.912953] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7

<7> [350.913301] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K

<7> [350.914001] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018

<7> [350.914411] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0

<7> [350.914746] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [350.915070] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x

<7> [350.915409] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported

<7> [350.923313] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583

<7> [350.923707] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [350.924030] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [350.924387] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)

<7> [350.924757] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4

<7> [350.925080] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no

<7> [350.925399] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [350.925688] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no

<7> [350.925969] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no

<7> [350.926262] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [350.926540] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no

<7> [350.926800] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes

<7> [350.927168] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [350.927493] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no

<7> [350.927790] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50

<7> [350.928169] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68

<7> [350.928539] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56

<7> [350.928889] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834

<7> [350.929225] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941

<7> [350.929572] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878

<7> [350.929922] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899

<7> [350.930306] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488

<7> [350.930665] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583

<7> [350.931009] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069

<7> [350.931367] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719

<7> [350.931704] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483

<7> [350.932035] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280

<7> [350.932423] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000

<7> [350.932779] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000

<7> [350.933126] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000

<7> [350.933485] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000

<7> [350.933824] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000

<7> [350.934149] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000

<7> [350.934500] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000

<7> [350.934865] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000

<7> [350.935883] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [350.936273] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228

<7> [350.936632] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)

<7> [350.936977] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5)

<7> [350.937334] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)

<7> [350.937694] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [350.938062] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812)

<7> [350.938478] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34)

<7> [350.938829] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [350.939174] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)

<7> [350.939529] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)

<7> [350.939876] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78)

<7> [350.940261] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)

<7> [350.940621] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0

<7> [350.940958] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [350.941307] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806

<7> [350.941652] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6

<7> [350.941981] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [350.942391] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [350.942743] i915 0000:00:02.0: [drm:intel_bios_init [i915]] port C trying to use the same DDC pin (0x3) as port A, disabling port A DVI/HDMI support

<7> [350.943085] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [350.943435] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0

<7> [350.943769] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000

<7> [350.944089] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [350.944428] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0

<7> [350.944769] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000

<7> [350.945122] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [350.945488] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0

<7> [350.945823] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000

<7> [350.946160] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a

<7> [350.946581] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [350.946956] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [350.947325] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [350.947692] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [350.948061] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [350.948422] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [350.948779] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [350.949203] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [350.949617] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0

<7> [350.949985] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [350.950560] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [350.950906] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [350.951258] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [350.951636] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [350.951985] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [350.952357] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [350.952725] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [350.953074] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [350.953439] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [350.953776] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [350.954114] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<7> [350.954659] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4

<7> [350.955151] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin

<7> [350.956877] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<6> [350.957801] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9)

<7> [350.957939] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us

<7> [350.958342] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)

<7> [350.958680] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)

<7> [350.959007] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)

<7> [350.959373] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)

<7> [350.959729] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)

<7> [350.960062] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)

<7> [350.960417] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)

<7> [350.960744] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)

<7> [350.972673] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 3 display pipes available.

<7> [350.978720] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0

<7> [350.979284] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz

<7> [350.979663] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] Max dotclock rate: 1113600 kHz

<7> [350.980075] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] using AUX A (VBT)

<7> [350.980474] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A]

<7> [350.984398] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)

<7> [350.984825] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2

<7> [350.985190] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2

<7> [350.985600] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless

<7> [350.985974] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa

<7> [350.986342] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300

<7> [350.986692] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002

<7> [350.987046] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName

<7> [350.987442] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz

<7> [350.987803] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0

<7> [350.988274] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0

<7> [350.988703] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000

<7> [350.989042] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [350.989386] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [350.989734] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [350.990082] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [350.990554] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60

<7> [350.991053] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [350.991643] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on

<7> [350.992022] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [350.992475] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [350.992825] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [350.993221] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068

<7> [350.993571] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled

<7> [351.197777] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00

<7> [351.198747] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001

<7> [351.199538] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6

<7> [351.200496] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1

<7> [351.205854] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [351.207787] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [351.209633] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [351.211581] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [351.213592] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [351.215534] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [351.217283] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [351.218897] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [351.220356] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [351.220372] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [351.220380] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [351.220478] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [351.220872] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa

<7> [351.221205] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms)

<7> [351.233873] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none

<7> [351.234418] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0)

<7> [351.234801] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, disabled, brightness 0/96000

<7> [351.235226] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000

<7> [351.235582] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [351.236154] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [351.236526] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [351.237003] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [351.237461] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60

<7> [351.238517] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] using AUX B (VBT)

<7> [351.238922] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B]

<7> [351.239678] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported

<7> [351.240035] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B]

<7> [351.240370] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT)

<7> [351.240940] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:262:DDI C (TC)/PHY C] using AUX C (platform default)

<7> [351.241402] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C]

<7> [351.241733] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT)

<7> [351.242167] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port D is not present

<7> [351.243366] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled

<7> [351.243881] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled

<7> [351.244362] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled

<7> [351.244712] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A

<7> [351.245073] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A

<7> [351.245468] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A

<7> [351.245834] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A

<7> [351.246178] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A

<7> [351.246541] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A

<7> [351.246886] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A

<7> [351.247267] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A

<7> [351.247641] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B

<7> [351.247988] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B

<7> [351.248396] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B

<7> [351.248739] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B

<7> [351.249080] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B

<7> [351.249466] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B

<7> [351.249836] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B

<7> [351.250177] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B

<7> [351.250546] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C

<7> [351.250895] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C

<7> [351.251227] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C

<7> [351.251592] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C

<7> [351.251966] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C

<7> [351.252346] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C

<7> [351.252697] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C

<7> [351.253039] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C

<7> [351.253397] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A

<7> [351.253760] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [351.254117] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A

<7> [351.254497] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B

<7> [351.254837] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C

<7> [351.255187] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A

<7> [351.255547] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0

<7> [351.255903] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [351.256369] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0

<7> [351.256821] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled

<7> [351.257181] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled

<7> [351.257555] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled

<7> [351.257908] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled

<7> [351.258446] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz

<7> [351.258799] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz

<7> [351.259127] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz

<7> [351.259599] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz

<7> [351.259928] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz

<7> [351.260263] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz

<7> [351.260591] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz

<7> [351.260926] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz

<7> [351.261293] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0

<7> [351.261669] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz

<7> [351.261995] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz

<7> [351.262336] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz

<7> [351.262662] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz

<7> [351.262983] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz

<7> [351.263386] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz

<7> [351.263732] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz

<7> [351.264061] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz

<7> [351.264407] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0

<7> [351.264757] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz

<7> [351.265077] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz

<7> [351.265435] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz

<7> [351.265795] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz

<7> [351.266126] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz

<7> [351.266478] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz

<7> [351.266805] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz

<7> [351.267118] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz

<7> [351.267461] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0

<7> [351.288940] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state]

<7> [351.289360] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state]

<7> [351.289705] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state]

<7> [351.290050] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [351.290416] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [351.290784] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [351.291450] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture

<7> [351.291767] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]

<7> [351.292085] MCR Steering: Default steering: group=0x0, instance=0x0

<7> [351.292111] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global

<7> [351.294771] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0

<7> [351.295163] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0

<7> [351.295567] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0

<7> [351.298168] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0

<7> [351.299092] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0

<7> [351.300630] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0

<7> [351.316850] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping

<7> [351.317274] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping

<7> [351.317614] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping

<7> [351.317941] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config

<7> [351.319932] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0

<7> [351.320287] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0

<7> [351.320577] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0

<7> [351.320868] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0

<7> [351.328021] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered

<7> [351.328640] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1

<7> [351.330742] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event

<7> [351.331690] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1

<7> [351.333213] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event

<7> [351.333932] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event

<7> [351.334822] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event

<6> [351.334940] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0

<7> [351.338759] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected

<6> [351.379658] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [351.387359] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input14

<6> [351.388351] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)

<7> [351.391313] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x810 (init value 0x810)

<7> [351.392454] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4

<7> [351.393825] [drm:intel_dsm_detect [i915]] no _DSM method for intel device

<7> [351.394207] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11

<7> [351.394501] i915 device info: slice0: 4 subslices, mask=0000000f

<6> [351.394528] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [351.394531] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<7> [351.395007] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]

<7> [351.395100] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [351.397612] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [351.398025] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [351.398629] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [351.398977] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [351.399615] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [351.399629] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [351.399638] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [351.399721] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [351.400081] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [351.403992] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [351.404509] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [351.405716] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3

<7> [351.406642] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [351.407445] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] status updated from unknown to connected

<7> [351.408872] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes :

<7> [351.408921] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [351.408934] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa

<7> [351.408945] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]

<7> [351.408980] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [351.409672] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] status updated from unknown to disconnected

<7> [351.409721] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected

<7> [351.409765] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]

<7> [351.409797] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [351.410224] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected

<7> [351.410292] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [351.410333] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]

<7> [351.410365] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [351.410783] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected

<7> [351.410828] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [351.410866] [drm:drm_client_modeset_probe] connector 239 enabled? yes

<7> [351.410876] [drm:drm_client_modeset_probe] connector 248 enabled? no

<7> [351.410882] [drm:drm_client_modeset_probe] connector 257 enabled? no

<7> [351.410887] [drm:drm_client_modeset_probe] connector 263 enabled? no

<7> [351.411184] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [351.411236] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239

<7> [351.411268] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0

<7> [351.411274] [drm:drm_client_modeset_probe] found mode 3200x1800

<7> [351.411280] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [351.411302] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)

<7> [351.411504] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane

<7> [351.411631] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one

<7> [351.430975] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x00180000

<7> [351.439717] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)

<7> [351.440187] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz

<7> [351.440631] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24

<7> [351.440987] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000

<7> [351.441464] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no

<7> [351.441836] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long

<7> [351.442188] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0

<7> [351.442588] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A]

<6> [351.442872] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)

<7> [351.442936] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.enable (expected 0, found 1)

<7> [351.443314] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.active (expected 0, found 1)

<7> [351.443687] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in cpu_transcoder (expected -1, found 4)

<7> [351.444059] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in lane_count (expected 0, found 4)

<7> [351.444453] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4209566/8388608 link 350797/524288)

<7> [351.444815] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in output_types (expected 0x00000000, found 0x00000100)

<7> [351.445165] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in framestart_delay (expected 0, found 1)

<7> [351.445560] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)

<7> [351.445908] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_htotal (expected 0, found 3316)

<7> [351.446283] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)

<7> [351.446636] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_end (expected 0, found 3316)

<7> [351.446994] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)

<7> [351.447408] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)

<7> [351.447771] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)

<7> [351.448132] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vtotal (expected 0, found 1816)

<7> [351.448529] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)

<7> [351.448906] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_end (expected 0, found 1816)

<7> [351.449298] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_start (expected 0, found 1802)

<7> [351.449646] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_end (expected 0, found 1807)

<7> [351.449991] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)

<7> [351.450499] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_htotal (expected 0, found 3316)

<7> [351.450854] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)

<7> [351.451202] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3316)

<7> [351.451579] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)

<7> [351.451930] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)

<7> [351.452305] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)

<7> [351.452660] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vtotal (expected 0, found 1816)

<7> [351.453015] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)

<7> [351.453385] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1816)

<7> [351.453722] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1802)

<7> [351.454064] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1807)

<7> [351.454439] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in pixel_multiplier (expected 0, found 1)

<7> [351.454807] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.flags (2) (expected 0, found 2)

<7> [351.455190] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.flags (8) (expected 0, found 8)

<7> [351.455610] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x0000004b)

<7> [351.455961] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in dpll_hw_state.cfgcr0 (expected 0x00000000, found 0x01c001a5)

<7> [351.456339] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in pipe_bpp (expected 0, found 24)

<7> [351.456789] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.pipe_mode.crtc_clock (expected 0, found 361310)

<7> [351.457129] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in hw.adjusted_mode.crtc_clock (expected 0, found 361310)

<7> [351.457510] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset mismatch in port_clock (expected 0, found 540000)

<7> [351.457939] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 1024), active pipes 0x0 -> 0x1

<7> [351.458352] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985

<7> [351.458694] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39

<7> [351.459051] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm

<7> [351.459421] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0

<7> [351.459772] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0

<7> [351.460145] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0

<7> [351.460561] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1

<7> [351.460928] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446

<7> [351.461293] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446

<7> [351.461739] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446

<7> [351.462118] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (180655 kHz) > [CRTC:98:pipe A] min cdclk (0 kHz)

<7> [351.462503] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz)

<7> [351.462872] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change

<7> [351.463216] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz

<7> [351.463599] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1

<7> [351.463978] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0

<7> [351.464358] i915 0000:00:02.0: [drm:intel_reference_shared_dpll.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0

<7> [351.464713] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset]

<7> [351.465056] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB

<7> [351.465419] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0

<7> [351.465782] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [351.466117] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [351.466479] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [351.466823] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [351.467163] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64

<7> [351.467536] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [351.467895] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [351.468268] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0

<7> [351.468637] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2

<7> [351.469004] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [351.469509] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [351.469854] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [351.470392] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa

<7> [351.470736] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [351.471073] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310

<7> [351.471502] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0

<7> [351.471874] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [351.472238] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [351.472724] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [351.473068] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [351.473495] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [351.473839] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [351.474180] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:240] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes

<7> [351.474620] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0

<7> [351.474971] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0

<7> [351.475393] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [351.475729] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [351.476063] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [351.476508] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [351.476849] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no

<7> [351.477187] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no

<7> [351.477606] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no

<7> [351.479315] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1

<7> [351.480226] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]

<7> [351.480799] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]

<7> [351.481186] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]

<7> [351.481612] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]

<7> [351.481950] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]

<7> [351.482517] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]

<7> [351.482960] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [351.483775] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [351.484194] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4

<7> [351.485104] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A]

<7> [351.485754] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0

<7> [351.487547] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on

<7> [351.488101] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [351.488830] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068

<7> [351.489203] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [351.489770] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on

<7> [351.490178] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000006b

<7> [351.702342] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [351.702783] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [351.705785] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00

<7> [351.705850] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [ENCODER:238:DDI A/PHY A] Using LINK_BW_SET value 14

<7> [351.706891] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0

<7> [351.707418] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1

<7> [351.709029] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0

<7> [351.709393] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0

<7> [351.711031] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK

<7> [351.711377] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3

<7> [351.713466] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1

<7> [351.713801] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1

<7> [351.715916] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful

<7> [351.716314] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4

<7> [351.717088] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A

<7> [351.718003] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]

<7> [351.718401] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A

<7> [351.718959] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000

<7> [351.724419] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1

<7> [351.724834] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]

<7> [351.735364] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]

<7> [351.735814] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]

<7> [351.736735] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0

<7> [351.737135] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp

<7> [351.737586] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<6> [351.739026] Console: switching to colour frame buffer device 400x112

<6> [351.760904] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device

<7> [351.768774] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]

<7> [351.769365] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]

<7> [351.769455] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [351.771424] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [351.771738] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [351.772019] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [351.772328] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [351.772924] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [351.772937] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [351.772944] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [351.773001] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [351.773321] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [351.774721] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [351.775005] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [351.776649] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes :

<7> [351.776696] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [351.776707] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa

<7> [351.776716] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]

<7> [351.776747] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [351.777215] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected

<7> [351.777266] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]

<7> [351.777295] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [351.777623] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [351.777653] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]

<7> [351.777681] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [351.778005] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [351.778034] [drm:drm_client_modeset_probe] connector 239 enabled? yes

<7> [351.778042] [drm:drm_client_modeset_probe] connector 248 enabled? no

<7> [351.778046] [drm:drm_client_modeset_probe] connector 257 enabled? no

<7> [351.778049] [drm:drm_client_modeset_probe] connector 263 enabled? no

<7> [351.778329] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [351.778384] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239

<7> [351.778390] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0

<7> [351.778394] [drm:drm_client_modeset_probe] found mode 3200x1800

<7> [351.778398] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config

<7> [351.778459] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)

<7> [351.785426] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]

<7> [351.785572] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]

<7> [351.785627] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [351.790151] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [351.790740] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [351.791056] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [351.791677] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [351.792917] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [351.792937] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [351.792945] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [351.792986] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [351.793840] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [351.796206] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [351.796630] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [351.798073] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes :

<7> [351.798113] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [351.798126] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa

<7> [351.798137] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]

<7> [351.798171] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [351.798646] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected

<7> [351.798683] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]

<7> [351.798714] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [351.799049] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [351.799084] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]

<7> [351.799115] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [351.799789] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [351.799823] [drm:drm_client_modeset_probe] connector 239 enabled? yes

<7> [351.799833] [drm:drm_client_modeset_probe] connector 248 enabled? no

<7> [351.799838] [drm:drm_client_modeset_probe] connector 257 enabled? no

<7> [351.799844] [drm:drm_client_modeset_probe] connector 263 enabled? no

<7> [351.799917] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [351.799937] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239

<7> [351.799944] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0

<7> [351.799950] [drm:drm_client_modeset_probe] found mode 3200x1800

<7> [351.799955] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config

<7> [351.799983] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)

<6> [351.801191] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100

<6> [351.808116] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)

<6> [351.820142] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])

<7> [351.820602] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [351.821210] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<7> [351.822175] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x810

<7> [351.841536] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

Results for igt@i915_module_load@reload