Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g0f0754413 (x86_64) (Linux: 6.4.0-rc3-linus-v6.4-rc3-g44c026a73be8+ x86_64)
Out 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.021s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.021s)
Dmesg
<6> [287.103638] Console: switching to colour dummy device 80x25
<6> [287.104636] [IGT] kms_force_connector_basic: executing
<7> [287.331699] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [287.332206] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [287.332411] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [287.333087] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [287.333105] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.333148] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [287.333494] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [287.333783] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [287.334268] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.334453] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.334956] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.335170] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.335178] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.335357] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.336897] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.336906] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.337087] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [287.337270] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [287.337357] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.337377] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [287.337568] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [287.337746] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [287.338184] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.338364] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.338726] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.338927] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.338933] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.339154] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.340569] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.340576] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.340754] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [287.340971] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [287.341164] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.341185] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [287.341375] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [287.341553] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [287.341932] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.342142] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.342504] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.342683] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.342688] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.342884] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.344411] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.344418] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.344597] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [287.344778] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<6> [287.345479] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [287.345714] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 2 or reprobing
<7> [287.345726] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.345752] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] status updated from disconnected to connected
<7> [287.346227] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.346480] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.347036] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.347324] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.347350] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.347629] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.349587] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.349613] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.350092] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes :
<7> [287.350125] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [287.350137] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [287.350147] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [287.350156] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [287.350166] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [287.350249] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.350529] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.350812] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.351341] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.351613] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.351634] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.351815] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.353345] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.353361] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.353621] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes :
<7> [287.353642] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [287.353649] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [287.353654] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [287.353659] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [287.353664] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [287.353955] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:65:VGA-1] EDID override set
<7> [287.354004] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.354079] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [287.354086] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [287.354101] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [287.354106] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [287.354125] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [287.354130] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [287.354244] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [287.354251] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [287.354260] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [287.354266] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [287.354274] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes :
<7> [287.354291] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [287.354297] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [287.354302] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [287.354306] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [287.354311] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [287.354316] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [287.354472] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:65:VGA-1] EDID override set
<7> [287.354505] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.354553] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [287.354559] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [287.354564] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:65:VGA-1] EDID changed, epoch counter 64
<7> [287.354582] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [287.354587] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [287.354604] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [287.354608] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [287.354712] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [287.354718] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [287.354727] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes :
<7> [287.354742] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [287.354747] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [287.354752] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [287.354757] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [287.354762] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [287.354946] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:65:VGA-1] EDID override reset
<7> [287.354980] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.355251] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.355476] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.355885] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.356103] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.356118] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:65:VGA-1] EDID changed, epoch counter 65
<7> [287.356132] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.356312] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.357757] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.357771] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.358077] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [287.358085] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [287.358094] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [287.358100] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [287.358108] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes :
<7> [287.358128] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [287.358133] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [287.358138] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [287.358143] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [287.358148] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [287.358343] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 2 to 0 or reprobing
<7> [287.358351] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.358372] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [287.358572] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [287.358752] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [287.359178] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.359372] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.359738] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.360031] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.360038] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.360217] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.361723] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.361731] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.361928] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [287.362134] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] status updated from connected to disconnected
<7> [287.362164] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [287.362376] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.362407] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [287.362680] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [287.362889] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [287.363280] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.363460] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.363820] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.364118] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.364128] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.364354] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.365786] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.365794] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.366055] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [287.366280] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [287.366478] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [287.367067] [drm:status_store] [CONNECTOR:61:LVDS-1] force updated from 0 to 0 or reprobing
<7> [287.367078] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [287.367105] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [287.367112] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [287.367187] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [287.367205] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [287.367263] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [287.367282] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [287.367288] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [287.367347] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [287.367363] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [287.367490] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:LVDS-1] EDID override reset
<7> [287.367517] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [287.367536] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [287.367542] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [287.367597] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [287.367613] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [287.367782] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [287.367793] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.367820] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [287.368160] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [287.368371] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [287.368754] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.368978] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.369359] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.369539] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.369546] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.369724] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.371312] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.371320] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.371502] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [287.371684] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [287.371764] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.371783] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [287.372061] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [287.372249] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [287.372621] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.372805] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.373234] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.373415] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.373421] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.373599] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.375034] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.375041] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.375220] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [287.375400] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [287.375562] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:65:VGA-1] EDID override reset
<7> [287.375590] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.375610] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [287.375802] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [287.376085] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [287.376462] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.376640] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.376979] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.377160] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.377165] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.377342] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.378749] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.378755] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.379054] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [287.379236] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [287.379455] [drm:status_store] [CONNECTOR:68:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [287.379464] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [287.379484] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [287.431521] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [287.446901] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [287.446910] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.447094] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [287.462890] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [287.462898] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [287.463087] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [287.463167] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [287.463187] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [287.514112] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [287.529888] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [287.529897] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.530081] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [287.545914] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [287.545931] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [287.546244] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [287.546535] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:68:HDMI-A-1] EDID override reset
<7> [287.546586] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [287.546618] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [287.597991] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [287.613891] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [287.613904] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.614112] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [287.629899] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [287.629907] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [287.630099] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [287.630320] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:76:DP-1] EDID override reset
<7> [287.630354] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1]
<7> [287.630374] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [287.630576] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] disconnected
<7> [287.630782] [drm:status_store] [CONNECTOR:81:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [287.630791] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [287.630811] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [287.631259] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [287.631442] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [287.631807] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [287.632047] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [287.632057] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.632239] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [287.633727] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [287.633734] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [287.633941] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [287.634040] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [287.634064] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [287.634449] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [287.634627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [287.635005] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [287.635313] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [287.635325] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.635620] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [287.637484] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [287.637497] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [287.637952] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [287.638240] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:81:HDMI-A-2] EDID override reset
<7> [287.638290] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [287.638321] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [287.638870] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [287.639149] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [287.639627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [287.639974] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [287.639983] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.640261] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [287.642026] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [287.642036] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [287.642306] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [287.642650] [drm:status_store] [CONNECTOR:85:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [287.642662] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [287.642692] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [287.643233] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [287.643510] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [287.643942] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [287.644220] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [287.644229] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.644489] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [287.646421] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [287.646432] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [287.646705] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [287.646816] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [287.646904] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [287.647434] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [287.647697] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [287.648235] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [287.648497] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [287.648506] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.648764] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [287.650549] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [287.650559] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [287.650883] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [287.651130] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:85:HDMI-A-3] EDID override reset
<7> [287.651172] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [287.651201] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [287.651722] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [287.652019] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [287.652507] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [287.652771] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [287.652778] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.653118] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [287.654916] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [287.654925] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [287.655195] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [287.655448] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:89:DP-2] EDID override reset
<7> [287.655490] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2]
<7> [287.655519] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [287.655808] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] disconnected
<7> [287.656131] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:93:DP-3] EDID override reset
<7> [287.656173] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3]
<7> [287.656204] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [287.656512] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] disconnected
<6> [287.658185] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [287.658471] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [287.658486] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.658524] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [287.658903] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [287.659185] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [287.659701] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.660039] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.660622] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.660983] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.660994] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.661275] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.663170] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.663181] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.663447] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [287.663713] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [287.663926] [drm:status_store] [CONNECTOR:61:LVDS-1] force updated from 0 to 0 or reprobing
<7> [287.663938] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [287.663974] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [287.663985] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [287.664108] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [287.664135] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [287.664227] [drm:status_store] [CONNECTOR:68:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [287.664238] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [287.664267] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [287.716687] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [287.732922] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [287.732935] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.733145] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [287.748887] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [287.748896] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [287.749088] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [287.749204] [drm:status_store] [CONNECTOR:81:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [287.749213] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [287.749233] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [287.749596] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [287.749932] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [287.750430] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [287.750700] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [287.750709] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.751021] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [287.752984] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [287.753002] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [287.753331] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [287.753489] [drm:status_store] [CONNECTOR:85:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [287.753502] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [287.753536] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [287.754139] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [287.754360] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [287.754727] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [287.754948] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [287.754955] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.755206] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [287.757177] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [287.757189] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [287.757482] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [287.758043] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [287.761046] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [287.761078] [drm:drm_client_modeset_probe]
<7> [287.761187] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [287.761224] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [287.761236] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [287.761360] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [287.761389] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [287.761402] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [287.761433] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [287.761749] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [287.762060] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [287.762572] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.763009] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [287.763463] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [287.763660] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.763667] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.763887] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [287.765427] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [287.765435] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [287.765616] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [287.765798] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [287.765821] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [287.765862] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [287.816884] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [287.832919] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [287.832936] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.833245] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [287.848923] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [287.848935] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [287.849213] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [287.849249] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1]
<7> [287.849279] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [287.849574] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] disconnected
<7> [287.849605] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [287.849633] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [287.850210] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [287.850475] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [287.850877] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [287.851159] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [287.851168] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.851430] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [287.853361] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [287.853371] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [287.853643] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [287.853675] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [287.853704] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [287.854255] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [287.854520] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [287.854931] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [287.855213] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [287.855222] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [287.855483] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [287.857398] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [287.857409] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [287.857698] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [287.857731] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2]
<7> [287.857761] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [287.858120] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] disconnected
<7> [287.858153] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3]
<7> [287.858184] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [287.858482] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] disconnected
<7> [287.858511] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [287.858520] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [287.858526] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [287.858532] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [287.858538] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [287.858544] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [287.858550] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [287.858556] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [287.858598] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [287.858617] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [287.858624] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [287.858631] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [287.858637] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [287.858672] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<6> [287.877731] Console: switching to colour frame buffer device 170x48
Created at 2023-05-21 23:51:21