Results for igt@i915_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-gc43a17c70 (x86_64) (Linux: 6.4.0-rc2-linus-v6.4-rc2-gf1fcbaa18b28+ x86_64)
Out 
Starting subtest: basic-rte
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 0
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x76/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x159/0x2b0 [i915]
   intel_atomic_commit_tail+0xa2d/0xd10 [i915]
   intel_atomic_commit+0x380/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
Wakeref count: 0
Subtest basic-rte: SUCCESS (1.767s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 0
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x76/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x159/0x2b0 [i915]
   intel_atomic_commit_tail+0xa2d/0xd10 [i915]
   intel_atomic_commit+0x380/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
Wakeref count: 0
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.767s)
Dmesg
<6> [99.181246] Console: switching to colour dummy device 80x25
<6> [99.181305] [IGT] i915_pm_rpm: executing
<6> [99.186347] [IGT] i915_pm_rpm: starting subtest basic-rte
<7> [99.186418] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [99.186836] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]
<7> [99.186855] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [99.186988] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.188140] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [99.188259] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [99.188576] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [99.188993] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [99.188998] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [99.189116] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [99.204066] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [99.204071] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [99.204192] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.204344] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [99.204439] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2]
<7> [99.204452] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [99.204577] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.205206] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.205321] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [99.205641] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.206056] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.206060] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [99.206173] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [99.220337] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.220342] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [99.220459] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.220596] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [99.220671] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1]
<7> [99.220682] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [99.220812] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.221243] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.221418] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected
<7> [99.225489] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]
<7> [99.225504] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [99.225640] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.226270] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [99.226411] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [99.227009] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [99.227528] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [99.227534] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [99.227657] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [99.242304] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [99.242309] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [99.242442] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.242587] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [99.243086] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2]
<7> [99.243098] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [99.243223] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.243875] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.243994] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [99.244292] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.244727] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.244733] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [99.244854] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [99.258981] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.258986] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [99.259103] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.259239] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [99.259786] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1]
<7> [99.259800] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [99.259930] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.260373] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.260521] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected
<7> [99.260844] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]
<7> [99.260856] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [99.260981] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.261623] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [99.261741] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [99.262341] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [99.262831] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [99.262835] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [99.262948] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [99.277120] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [99.277125] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [99.277242] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.277397] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [99.277431] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2]
<7> [99.277443] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [99.277570] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.278198] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.278313] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [99.278627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.279042] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.279046] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [99.279159] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [99.293299] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.293303] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [99.293437] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.293583] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [99.293610] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1]
<7> [99.293621] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [99.293748] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.294175] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.294313] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected
<7> [100.296026] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.298395] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.304638] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.329168] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.335049] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [100.335713] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [100.336279] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.337092] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.338377] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.338992] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [100.339092] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [100.339925] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.340564] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.340569] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.340688] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [100.355354] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.355359] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [100.355479] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.355623] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] Same epoch counter 6
<7> [100.355646] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [100.355776] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.356769] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.356894] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.357207] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.357660] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.357666] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.357787] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.371974] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.371979] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.372100] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.372243] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [100.372384] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.372518] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.372988] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.373551] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.373685] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.373838] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.374442] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.374626] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.375631] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [100.375613] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.375632] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [100.379319] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.403674] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.409408] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [100.409902] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.410025] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.410479] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.410633] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [100.410751] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.410885] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.411297] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.411853] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.412032] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.412168] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.412739] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.412885] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.414405] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [100.414375] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.416982] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.441106] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.445915] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [100.446435] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.446584] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.446714] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.447125] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.447693] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.447830] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.447960] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.448531] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.448720] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.449211] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [100.449704] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.453337] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.477706] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.483899] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [100.484440] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.484595] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.485715] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.485905] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [100.486245] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.486780] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.486788] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.486967] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [100.502188] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.502195] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [100.502363] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.502544] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] Same epoch counter 6
<7> [100.502569] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [100.502778] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.503871] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.504060] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.504695] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.505196] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.505204] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.505415] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.520657] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.520662] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.520778] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.520916] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [100.520931] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [100.521055] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.521506] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.521649] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [100.521668] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [100.521832] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.522908] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.523061] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [100.523699] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.524206] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.524212] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.524384] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [100.539047] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.539053] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [100.539169] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.539309] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] Same epoch counter 6
<7> [100.539323] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [100.539506] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.540151] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.540316] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.540675] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.541093] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.541099] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.541248] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.555946] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.555951] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.556070] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.556211] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [100.556225] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [100.556370] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.556805] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.556986] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [100.557008] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.558027] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.561338] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.651529] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [100.664081] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.681179] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [100.682179] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.682343] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.682481] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.682670] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.683219] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.683389] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.683536] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.684106] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.684283] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.684781] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [100.685746] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.689307] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.713727] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.719880] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [100.720475] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.720693] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.720891] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.721382] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.721924] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.722123] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.722318] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.722961] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.723180] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.723704] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [100.723709] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [100.724736] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.728370] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.752838] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.759222] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [100.759798] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.759985] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.760736] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.760931] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [100.761307] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.761814] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.761821] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.762011] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [100.776766] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.776774] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [100.776965] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.777200] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] Same epoch counter 6
<7> [100.777225] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [100.777456] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.778566] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.778756] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.779138] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.779653] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.779662] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.779840] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.794557] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.794562] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.794687] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.794838] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [100.794862] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.795848] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.799333] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.823793] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.829929] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [100.830539] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.830736] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.830866] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.831386] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.831887] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.832021] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.832175] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.832767] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.833022] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.833015] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [100.834013] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.837368] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.861776] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.867923] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [100.868491] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.868646] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.869118] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.869301] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [100.869343] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [100.869518] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.869909] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.870055] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [100.870697] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.871172] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.871177] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.871320] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [100.885976] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.885983] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [100.886129] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.886309] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] Same epoch counter 6
<7> [100.886343] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [100.886514] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.887560] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.887716] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.888051] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.888521] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.888528] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.888688] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.903421] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.903426] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.903545] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.903686] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [100.903701] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [100.903827] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.904255] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.904406] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [100.904422] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.905403] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.909066] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.945422] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.951230] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [100.951749] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.951893] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.952054] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.952531] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.953687] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [100.954053] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [100.954279] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [100.954274] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [100.954697] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.954853] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [100.955224] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [100.955425] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.955433] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.955632] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [100.958615] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.958622] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [100.958778] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.958946] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.959110] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.959720] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.959904] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] Same epoch counter 6
<7> [100.959935] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [100.960112] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.961186] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.961357] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.961999] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.962535] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.962543] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.962747] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.977432] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.977439] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.977588] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.977770] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [100.977912] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.978079] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.978551] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.979102] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.979282] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.979481] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.980096] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.980258] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.981293] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [100.981773] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [100.985370] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [101.009722] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [101.015985] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [101.016982] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [101.017106] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.017566] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [101.017737] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [101.017761] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [101.017888] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.018887] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [101.019021] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [101.019635] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [101.020133] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [101.020139] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.020269] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [101.035000] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [101.035005] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [101.035121] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [101.035260] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] Same epoch counter 6
<7> [101.035274] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [101.035460] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.036090] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.036219] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [101.036558] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.036985] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.036991] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.037124] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [101.051763] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.051768] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [101.051886] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [101.052031] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [101.052046] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [101.052171] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.052610] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [101.052750] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [101.052765] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [101.053740] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [101.057324] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [101.107436] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [101.116027] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [101.117300] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [101.117371] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [101.117846] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.118086] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [101.118622] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [101.119165] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [101.119445] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [101.119803] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [101.120041] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [101.120426] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [101.120638] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [101.120646] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.120832] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [101.123897] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [101.123905] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [101.124103] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] Same epoch counter 6
<7> [101.124127] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [101.124598] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.124787] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [101.125163] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.125395] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.125402] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.125588] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [101.128654] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.128662] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [101.128861] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [101.128884] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [101.129113] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [101.132143] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [101.132420] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [101.132656] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [101.132883] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [101.133559] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [101.304082] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.304219] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [101.304677] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [101.305241] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [101.305390] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [101.305520] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [101.306086] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [101.306385] [IGT] i915_pm_rpm: exiting, ret=0
<7> [101.307410] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.307542] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [101.307975] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [101.308570] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [101.308707] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [101.308837] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [101.309411] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [101.309657] Console: switching to colour frame buffer device 128x48
<7> [101.310034] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [101.310163] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [101.310587] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [101.311137] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [101.311272] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [101.311411] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [101.311973] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2023-05-14 21:33:28