Results for igt@i915_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g2f0a07378 (x86_64) (Linux: 6.3.0-linus-v6.3-g457391b03803+ x86_64)
Out 
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 0
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xb6/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x79/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x159/0x2b0 [i915]
   intel_atomic_commit_tail+0xb52/0xe30 [i915]
   intel_atomic_commit+0x380/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1ec/0x740
Wakeref count: 0
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.268s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.268s)
Dmesg
<6> [78.111196] Console: switching to colour dummy device 80x25
<6> [78.111245] [IGT] i915_pm_rpm: executing
<7> [78.119314] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [78.120058] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [78.120091] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [78.120340] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.120936] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.121220] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [78.121353] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2]
<7> [78.121380] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [78.121619] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.122262] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [78.122920] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [78.123634] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [78.125004] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [78.125709] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [78.126262] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [78.126546] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [78.126813] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [78.127178] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [78.128005] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.128278] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2] disconnected
<7> [78.128407] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [78.128433] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [78.128669] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.129904] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.130155] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [78.130950] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.131559] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.131569] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [78.131862] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [78.157291] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.157299] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [78.157463] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.157653] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [78.162257] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [78.162276] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [78.162435] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.162926] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.163118] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [78.163626] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2]
<7> [78.163643] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [78.163793] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.164299] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [78.164803] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [78.165386] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [78.166631] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [78.167692] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [78.168448] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [78.168607] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [78.168749] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [78.168888] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [78.169576] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.169727] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2] disconnected
<7> [78.170165] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [78.170179] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [78.170297] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.171386] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.171498] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [78.172182] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.172672] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.172676] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [78.172785] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [78.198432] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.198436] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [78.198556] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.198681] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [78.198990] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [78.199027] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [78.199158] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.199636] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.199763] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [78.199788] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2]
<7> [78.199815] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [78.199943] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.200433] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [78.200954] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [78.201524] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [78.202695] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [78.203793] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [78.204524] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [78.204667] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [78.204795] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [78.204919] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [78.205518] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.205647] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2] disconnected
<7> [78.205673] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [78.205685] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [78.205798] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.207381] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.207518] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [78.208691] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.209250] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.209269] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [78.209389] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [78.234528] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.234533] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [78.234640] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.234765] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [89.279573] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [89.284810] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [89.309081] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [89.315405] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [89.316177] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [89.317223] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [89.316787] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.318044] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.318592] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [89.318810] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.319156] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.319715] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.320323] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.320566] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.320801] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.321506] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.322259] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [89.322523] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [89.327155] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [89.351789] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [89.357386] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [89.357565] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.357731] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.358211] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.358785] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.358951] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.359123] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.359739] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.359920] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [89.361029] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [89.361437] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [89.363738] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [89.388252] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [89.394427] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [89.394606] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.395250] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.395910] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.396573] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [89.398921] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [89.399720] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [89.400374] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [89.400921] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.401231] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.401511] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.402261] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.402580] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [89.402618] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [89.402883] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.404645] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.404985] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.405811] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.406422] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.406433] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.406680] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.432517] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.432525] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.432699] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.432882] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [89.432918] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [89.435881] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [89.460244] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [89.465012] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [89.465189] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.465348] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.465812] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.466392] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.466544] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.466690] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.467308] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.467471] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [89.468096] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [89.470786] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [89.495190] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [89.500074] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [89.500246] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.500809] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.501107] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [89.501146] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [89.501345] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.501888] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.502407] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.502991] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [89.504570] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [89.505320] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [89.505871] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [89.506160] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.506395] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.506623] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.507320] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.507582] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [89.507613] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [89.507829] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.509074] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.509313] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.510134] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.510674] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.510683] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.510883] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.535521] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.535528] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.535681] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.535860] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [89.535886] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [89.536061] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.536564] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.536789] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [89.536809] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [89.537007] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.537512] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.538035] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.538600] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [89.539722] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [89.540848] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [89.541476] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [89.541651] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.541803] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.541950] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.542574] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.542731] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [89.542747] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [89.542870] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.543988] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.544116] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.544813] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.545334] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.545341] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.545471] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.568995] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.569000] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.569112] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.569242] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [89.569258] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [89.571631] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [89.669337] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state
<7> [89.681238] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [89.693618] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [89.701586] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [89.701899] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.702275] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.702919] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.703725] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.704087] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.704398] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.705192] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.705625] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [89.705816] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.706148] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.706762] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.707470] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.707789] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.708207] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.709062] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.709479] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [89.709656] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.709987] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.710602] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.711270] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.711615] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.711926] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.712743] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.713284] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [89.715060] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [89.718060] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [89.742781] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [89.747756] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [89.747873] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.748413] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.748657] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [89.748681] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [89.748885] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.749419] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.749930] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.750507] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [89.751719] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [89.752737] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [89.753568] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [89.753779] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.753980] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.754161] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.754793] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.754989] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [89.755009] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [89.755156] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.756290] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.756469] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.757214] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.757699] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.757705] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.757841] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.781929] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.781934] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.782081] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.782275] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [89.782306] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [89.782455] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.782930] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.783098] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [89.783113] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [89.783258] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.783712] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.784249] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.784792] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [89.785892] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [89.787000] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [89.787761] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [89.787909] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.788061] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.788221] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.788796] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.788926] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [89.788940] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [89.789090] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.790257] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.790387] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.791072] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.791552] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.791556] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.791663] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.817886] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.817891] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.818038] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.818216] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [89.818232] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [89.820972] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [89.927947] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [89.935013] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [89.935268] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.935508] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.936117] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.939780] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [89.939816] [drm:drm_client_modeset_probe]
<7> [89.940374] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1]
<7> [89.940483] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [89.941073] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.941609] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.941928] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.942724] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.943716] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected
<7> [89.943753] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2]
<7> [89.943785] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [89.944340] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.945061] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.945917] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.946598] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [89.949566] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [89.950445] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [89.951245] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [89.951777] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.952133] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.952452] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.953332] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.953818] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:107:DP-2] disconnected
<7> [89.953869] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [89.953918] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [89.954281] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.956460] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.956756] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.957669] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.958460] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.958477] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.958883] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.987120] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.987127] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.987273] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.987441] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [89.987458] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [89.987467] [drm:drm_client_modeset_probe] connector 95 enabled? no
<7> [89.987471] [drm:drm_client_modeset_probe] connector 107 enabled? no
<7> [89.987474] [drm:drm_client_modeset_probe] connector 113 enabled? no
<7> [89.987563] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [89.987579] [drm:drm_client_modeset_probe] picking CRTCs for 1024x768 config
<7> [89.987630] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [89.987810] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.988332] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.988515] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [89.988669] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.988828] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.989302] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.989890] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.990092] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.990251] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.990861] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [89.991151] [IGT] i915_pm_rpm: exiting, ret=0
<7> [89.991138] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [89.991295] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.991778] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [89.992321] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [89.992860] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [89.994005] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [89.995001] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [89.995771] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [89.995926] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.996063] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.996188] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.996765] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.996898] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [89.996941] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [89.997065] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.998155] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.998269] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.998957] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.999437] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.999441] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.999550] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.027424] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.027427] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.027537] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.027666] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [90.027814] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.027954] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [90.028433] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [90.029063] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [90.029194] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [90.029320] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [90.029898] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [90.030186] Console: switching to colour frame buffer device 128x48
<7> [90.030512] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.030635] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [90.031085] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [90.031653] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [90.031787] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [90.031909] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [90.032573] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2023-04-23 20:31:27