Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g2f0a07378 (x86_64) (Linux: 6.3.0-linus-v6.3-g457391b03803+ x86_64)
Out 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.473s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.473s)
Dmesg
<6> [139.977347] Console: switching to colour dummy device 80x25
<6> [139.977643] [IGT] kms_force_connector_basic: executing
<7> [139.980003] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [139.980395] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [139.980526] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [139.981003] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [139.981010] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [139.981027] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.033044] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.042468] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.042477] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.042629] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.049773] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.049776] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.049856] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [140.049899] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.049911] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.101167] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.110670] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.110682] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.110887] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.118093] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.118096] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.118175] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [140.118248] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.118259] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.171103] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.180582] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.180593] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.180850] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.188057] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.188060] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.188140] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<6> [140.188394] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [140.188497] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [140.188502] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.188512] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.240323] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.250159] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.250181] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.250408] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.257689] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.257695] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.257774] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] status updated from disconnected to connected
<7> [140.257809] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [140.257817] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [140.257821] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [140.257824] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [140.257826] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [140.257828] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [140.257863] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.257874] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.308750] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.318241] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.318262] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.318501] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.325714] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.325720] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.325826] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [140.325837] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [140.325841] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [140.325843] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [140.325845] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [140.325847] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [140.325989] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:249:HDMI-A-1] EDID override set
<7> [140.326001] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.326010] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.326104] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD monitor IGT
<7> [140.326107] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD size 24, SAD count 0
<7> [140.378512] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.389582] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [140.389814] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [140.389828] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [140.389841] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [140.389851] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [140.389863] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [140.389894] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [140.389903] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [140.389911] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [140.389919] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [140.389926] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [140.389934] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [140.390189] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:249:HDMI-A-1] EDID override set
<7> [140.390234] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.390263] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.390582] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD monitor IGT
<7> [140.390590] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD size 24, SAD count 0
<7> [140.390597] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:249:HDMI-A-1] EDID changed, epoch counter 4
<7> [140.442752] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.451618] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [140.451690] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [140.451715] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [140.451720] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [140.451734] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [140.451738] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [140.451741] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [140.451743] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [140.451746] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [140.451845] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:249:HDMI-A-1] EDID override reset
<7> [140.451860] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.451870] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.502929] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.512847] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.512900] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.513353] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.521240] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.521246] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.521325] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:249:HDMI-A-1] EDID changed, epoch counter 5
<7> [140.521368] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [140.521372] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [140.521376] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [140.521379] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [140.521383] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [140.521397] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [140.521399] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [140.521402] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [140.521404] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [140.521406] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [140.521536] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [140.521540] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.521552] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.574538] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.584342] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.584355] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.584588] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.591962] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.591965] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.592053] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] status updated from connected to disconnected
<7> [140.592069] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [140.592147] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.592157] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.644140] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.653661] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.653672] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.653893] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.661244] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.661247] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.661335] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [140.661540] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [140.661943] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:236:DP-1] EDID override reset
<7> [140.661975] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [140.661988] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [140.667024] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: Base DPCD: 12 14 c4 01 01 00 01 c0 02 00 06 00 00 00 80
<7> [140.667045] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 14 14 c4 01 01 00 01 c0 02 00 06 00 00 00 80
<7> [140.668432] i915 0000:00:02.0: [drm:intel_dp_init_lttpr_and_dprx_caps [i915]] [ENCODER:235:DDI B/PHY B] LTTPR common capabilities: 00 00 00 00 00 00 00 00
<7> [140.672695] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: Base DPCD: 12 14 c4 01 01 00 01 c0 02 00 06 00 00 00 80
<7> [140.672708] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 14 14 c4 01 01 00 01 c0 02 00 06 00 00 00 80
<7> [140.674166] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP sink: OUI 00-e0-4c dev-ID Dp1.2 HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [140.675621] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [140.677179] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [140.678684] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: yes, sink: no, modparam: yes
<7> [140.678800] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [140.678911] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [140.679018] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [140.698569] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:DP-1] Supported Monitor Refresh rate range is 40 Hz - 61 Hz
<7> [140.698576] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:DP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [140.698579] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:DP-1] ELD monitor LG HDR 4K
<7> [140.698582] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:DP-1] ELD size 32, SAD count 1
<7> [140.698595] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:DP-1] VRR capable: yes
<7> [140.698692] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:DP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [140.700156] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [140.700236] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:DP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [140.700311] [drm:drm_detect_monitor_audio] Monitor has basic audio support
<7> [140.701839] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] probed modes :
<7> [140.701850] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 533250 3840 3888 3920 4000 2160 2214 2219 2222 0x48 0x9
<7> [140.701855] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 30 266640 3840 3848 3992 4000 2160 2214 2219 2222 0x40 0x9
<7> [140.701857] [drm:drm_mode_debug_printmodeline] Modeline "2560x1440": 60 241500 2560 2608 2640 2720 1440 1443 1448 1481 0x40 0x9
<7> [140.701859] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5
<7> [140.701861] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5
<7> [140.701863] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148352 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0x5
<7> [140.701865] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [140.701868] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [140.701870] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 83500 1280 1352 1480 1680 800 803 809 831 0x40 0x6
<7> [140.701872] [drm:drm_mode_debug_printmodeline] Modeline "1152x864": 60 81768 1152 1216 1336 1520 864 867 871 897 0x0 0x6
<7> [140.701874] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [140.701876] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [140.701878] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74176 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [140.701881] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [140.701883] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [140.701885] [drm:drm_mode_debug_printmodeline] Modeline "720x480": 60 27027 720 736 798 858 480 489 495 525 0x40 0xa
<7> [140.701887] [drm:drm_mode_debug_printmodeline] Modeline "720x480": 60 27000 720 736 798 858 480 489 495 525 0x40 0xa
<7> [140.701889] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25200 640 656 752 800 480 490 492 525 0x40 0xa
<7> [140.701891] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [140.701893] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [140.702027] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [140.702031] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.702041] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.753694] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.762629] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.762637] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.762819] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.770000] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.770003] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.770089] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [140.770144] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.770156] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.820650] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.830102] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.830114] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.830322] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.837483] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.837486] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.837572] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [140.837758] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:249:HDMI-A-1] EDID override reset
<7> [140.837780] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.837792] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.841890] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [140.842102] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC4
<7> [140.842276] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC3
<7> [140.842410] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC2
<7> [140.842536] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC1
<7> [140.842730] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected)
<7> [140.842730] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected)
<7> [140.842730] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port G/TC#4: TC port mode reset (tbt-alt -> disconnected)
<7> [140.842731] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected)
<7> [140.842829] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC3
<7> [140.842933] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC2
<7> [140.843040] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC4
<7> [140.843205] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC1
<7> [140.843365] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [140.889772] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.898508] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.898515] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.898603] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.905611] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.905614] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.905710] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [140.905878] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:255:DP-2] EDID override reset
<7> [140.905901] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [140.905911] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [140.906011] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [140.906117] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC1
<7> [140.906252] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC1
<7> [140.906350] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [140.906453] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [140.906556] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC1
<7> [140.906701] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port D/TC#1: PHY ownership not required (live status 00)
<7> [140.906796] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt)
<7> [140.906891] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC1
<7> [140.906991] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [140.907126] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [140.907224] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:264:DP-3] EDID override reset
<7> [140.907235] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [140.907244] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [140.907340] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [140.907442] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC2
<7> [140.907572] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC2
<7> [140.907675] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [140.907783] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [140.907887] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC2
<7> [140.908016] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port E/TC#2: PHY ownership not required (live status 00)
<7> [140.908102] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt)
<7> [140.908189] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC2
<7> [140.908286] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [140.908421] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [140.908490] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:273:DP-4] EDID override reset
<7> [140.908500] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-4]
<7> [140.908510] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-4]
<7> [140.908610] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [140.908725] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC3
<7> [140.908860] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC3
<7> [140.908960] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [140.909061] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [140.909163] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC3
<7> [140.909301] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port F/TC#3: PHY ownership not required (live status 00)
<7> [140.909396] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt)
<7> [140.909491] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC3
<7> [140.909592] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [140.909733] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-4] disconnected
<7> [140.909802] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:282:DP-5] EDID override reset
<7> [140.909813] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:282:DP-5]
<7> [140.909822] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:282:DP-5]
<7> [140.909921] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [140.910023] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC4
<7> [140.910154] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC4
<7> [140.910256] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [140.910361] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [140.910467] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC4
<7> [140.910598] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port G/TC#4: PHY ownership not required (live status 00)
<7> [140.910700] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port G/TC#4: TC port mode reset (disconnected -> tbt-alt)
<7> [140.910797] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC4
<7> [140.910897] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [140.911032] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:282:DP-5] disconnected
<6> [140.911441] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [140.911530] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [140.911535] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [140.911546] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [140.963973] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [140.972732] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.972740] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [140.972906] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [140.980045] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [140.980048] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [140.980131] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [140.980307] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [141.007110] Console: switching to colour frame buffer device 480x135
Created at 2023-04-23 20:31:27