Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g066fa5410 (x86_64) (Linux: 6.3.0-rc7-linus-v6.3-rc7-g6a8f57ae2eb0+ x86_64)
Out 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.082s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.082s)
Dmesg
<6> [112.106712] Console: switching to colour dummy device 80x25
<6> [112.106977] [IGT] kms_force_connector_basic: executing
<7> [112.163154] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [112.163645] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [112.163824] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [112.164233] [drm:status_store] [CONNECTOR:76:VGA-1] force updated from 0 to 0 or reprobing
<7> [112.164240] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.164264] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1
<7> [112.164469] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [112.164635] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [112.164979] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.165123] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.165422] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.165593] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.165599] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.165740] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.167123] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.167129] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.167335] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.167352] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.167358] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.167363] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.167367] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.167371] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.167426] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.167460] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1
<7> [112.167630] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [112.167771] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [112.168102] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.168247] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.168540] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.168686] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.168691] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.168826] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.170058] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.170063] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.170268] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.170285] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.170290] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.170295] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.170299] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.170304] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.170348] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.170365] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1
<7> [112.170572] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [112.170724] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [112.171062] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.171209] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.171535] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.171679] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.171683] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.171818] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.173081] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.173086] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.173279] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.173294] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.173299] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.173303] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.173307] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.173311] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [112.173618] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [112.173757] [drm:status_store] [CONNECTOR:76:VGA-1] force updated from 0 to 2 or reprobing
<7> [112.173762] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.173976] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.174119] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.174415] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.174576] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.174588] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.174727] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.176097] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.176108] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.176318] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.176335] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.176341] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.176346] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.176351] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.176356] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.176391] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.176638] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.176781] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.177098] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.177237] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.177246] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.177386] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.178610] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.178619] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.178831] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.178847] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.178852] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.178857] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.178862] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.178866] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.245389] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:76:VGA-1] EDID override set
<7> [112.245441] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.245668] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:76:VGA-1] ELD monitor IGT
<7> [112.245676] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:76:VGA-1] ELD size 24, SAD count 0
<7> [112.245703] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:76:VGA-1] ELD monitor IGT
<7> [112.245708] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:76:VGA-1] ELD size 24, SAD count 0
<7> [112.245725] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:76:VGA-1] ELD monitor IGT
<7> [112.245729] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:76:VGA-1] ELD size 24, SAD count 0
<7> [112.245813] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.245819] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [112.245828] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.245833] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [112.245839] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.245855] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [112.245860] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [112.245864] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.245868] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.245872] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.245983] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:76:VGA-1] EDID override reset
<7> [112.246059] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.246274] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.246543] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.246865] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.247007] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.247017] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:76:VGA-1] EDID changed, epoch counter 3
<7> [112.247028] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.247209] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.248576] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.248587] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.248779] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [112.248785] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [112.248791] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [112.248796] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [112.248802] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.248817] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.248821] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.248825] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.248829] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.248833] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.248974] [drm:status_store] [CONNECTOR:76:VGA-1] force updated from 2 to 0 or reprobing
<7> [112.248980] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.248996] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1
<7> [112.249149] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [112.249290] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [112.249667] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.249809] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.250128] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.250268] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.250273] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.250460] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.251917] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.251923] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.252125] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.252140] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.252145] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.252150] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.252155] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.252159] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.252196] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.252211] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1
<7> [112.252361] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [112.252528] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [112.252900] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.253038] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.253352] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.253501] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.253505] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.253683] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.254926] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.254931] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.255125] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.255140] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.255145] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.255149] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.255153] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.255157] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.255306] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [112.255743] [drm:status_store] [CONNECTOR:76:VGA-1] force updated from 0 to 0 or reprobing
<7> [112.255749] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.255765] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1
<7> [112.255918] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [112.256058] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [112.256390] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.256556] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.256892] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.257028] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.257033] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.257168] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.258562] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.258567] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.258760] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.258774] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.258780] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.258784] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.258788] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.258793] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.258826] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.258841] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1
<7> [112.259028] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [112.259165] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [112.259509] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.259652] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.259962] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.260096] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.260100] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.260233] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.261520] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.261525] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.261713] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.261727] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.261732] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.261737] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.261741] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.261744] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.261839] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:76:VGA-1] EDID override reset
<7> [112.261857] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.261873] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1
<7> [112.262018] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [112.262153] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [112.262501] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.262647] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.262959] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.263093] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.263098] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.263232] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.264480] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.264484] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.264672] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.264686] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.264691] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.264695] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.264699] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.264703] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.264838] [drm:status_store] [CONNECTOR:79:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [112.264843] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1]
<7> [112.264858] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:79:HDMI-A-1]
<7> [112.265191] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [112.265328] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [112.265679] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [112.265824] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.265828] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.265961] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [112.267374] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.267380] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [112.267550] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] disconnected
<7> [112.267602] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1]
<7> [112.267618] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:79:HDMI-A-1]
<7> [112.267958] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [112.268096] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [112.268423] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [112.268582] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.268586] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.268722] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [112.269929] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.269934] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [112.270073] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] disconnected
<7> [112.270180] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:79:HDMI-A-1] EDID override reset
<7> [112.270199] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1]
<7> [112.270215] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:79:HDMI-A-1]
<7> [112.270562] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [112.270718] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [112.271053] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [112.271191] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.271195] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.271331] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [112.272629] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.272634] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [112.272780] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] disconnected
<7> [112.272928] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:87:DP-1] EDID override reset
<7> [112.272949] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1]
<7> [112.272965] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:87:DP-1]
<7> [112.273139] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] disconnected
<6> [112.273765] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [112.273881] [drm:status_store] [CONNECTOR:76:VGA-1] force updated from 0 to 0 or reprobing
<7> [112.273887] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1]
<7> [112.273903] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1
<7> [112.274056] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [112.274197] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [112.274498] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.274670] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [112.275010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [112.275163] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.275168] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.275306] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [112.276781] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [112.276787] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [112.276992] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes :
<7> [112.277008] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.277013] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.277018] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.277023] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.277027] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.277076] [drm:status_store] [CONNECTOR:79:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [112.277081] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1]
<7> [112.277097] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:79:HDMI-A-1]
<7> [112.277435] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [112.277611] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [112.277930] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [112.278069] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.278074] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.278211] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [112.279625] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.279631] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [112.279773] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] disconnected
<7> [112.279999] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [112.297854] Console: switching to colour frame buffer device 128x48
Created at 2023-04-17 00:16:47