Results for igt@kms_addfb_basic@too-high

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gb4252c86f (x86_64) (Linux: 6.3.0-rc6-linus-v6.3-rc6-g09a9639e56c0+ x86_64)
Out	Starting subtest: too-high Subtest too-high: SUCCESS (0.001s)
Err	Starting subtest: too-high Subtest too-high: SUCCESS (0.001s)
Dmesg	<6> [174.003285] Console: switching to colour dummy device 80x25 <6> [174.003361] [IGT] kms_addfb_basic: executing <7> [174.251597] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [174.252748] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [174.252991] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [174.253259] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] bad framebuffer format .... little-endian (0x00000000) <7> [174.253512] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:96] <7> [174.253731] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:96] <7> [174.253831] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:96] <7> [174.257878] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] <7> [174.257908] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1 <7> [174.258142] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0 <7> [174.258350] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug <7> [174.258764] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [174.258951] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [174.259300] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [174.259501] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [174.259509] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.259689] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [174.261126] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [174.261133] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [174.261374] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found] <7> [174.261571] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected <7> [174.262026] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] <7> [174.262048] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1] <7> [174.314490] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5 <7> [174.331290] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [174.331300] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.331472] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [174.347280] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [174.347287] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [174.347464] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected <7> [174.347984] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] <7> [174.348005] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1] <7> [174.348196] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] disconnected <7> [174.348785] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] <7> [174.348808] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2] <7> [174.349203] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [174.349407] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [174.349788] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [174.349969] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [174.349975] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.350150] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [174.351603] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [174.351609] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [174.351793] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected <7> [174.352365] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] <7> [174.352387] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3] <7> [174.352775] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [174.352957] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry <7> [174.353303] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [174.353495] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [174.353501] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.353679] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1 <7> [174.355082] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [174.355089] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0 <7> [174.355313] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected <7> [174.355828] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] <7> [174.355849] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2] <7> [174.356050] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] disconnected <7> [174.356614] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] <7> [174.356636] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3] <7> [174.356845] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] disconnected <7> [174.357136] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] <7> [174.357159] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor <7> [174.357166] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0 <7> [174.357274] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes : <7> [174.357301] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9 <7> [174.357328] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] <7> [174.357347] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1 <7> [174.357557] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0 <7> [174.357742] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug <7> [174.358073] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [174.358361] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [174.358828] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [174.359089] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [174.359099] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.359379] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [174.361134] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [174.361144] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [174.361428] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found] <7> [174.361689] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected <7> [174.362029] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 2 or reprobing <7> [174.362040] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] <7> [174.362069] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] status updated from disconnected to connected <7> [174.362297] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [174.362565] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [174.363040] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [174.363330] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [174.363352] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.363614] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [174.365517] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [174.365539] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [174.365870] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes : <7> [174.365899] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [174.365910] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [174.365919] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 <7> [174.365929] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 <7> [174.365937] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [174.366007] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] <7> [174.366253] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [174.366519] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [174.366967] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [174.367210] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [174.367252] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.367512] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [174.369278] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [174.369297] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [174.369648] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes : <7> [174.369675] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [174.369685] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [174.369694] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 <7> [174.369702] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 <7> [174.369710] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [174.369750] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] <7> [174.369779] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1] <7> [174.421219] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5 <7> [174.437257] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [174.437267] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.437453] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [174.453263] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [174.453273] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [174.453473] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected <7> [174.453530] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] <7> [174.453551] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1] <7> [174.453752] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] disconnected <7> [174.453788] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] <7> [174.453807] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2] <7> [174.454208] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [174.454442] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [174.454812] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [174.454991] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [174.454997] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.455187] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [174.456676] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [174.456683] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [174.456867] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected <7> [174.456911] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] <7> [174.456931] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3] <7> [174.457322] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [174.457504] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry <7> [174.457866] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [174.458044] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [174.458049] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.458270] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1 <7> [174.459698] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [174.459705] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0 <7> [174.459888] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected <7> [174.459930] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] <7> [174.459950] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2] <7> [174.460180] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] disconnected <7> [174.460222] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] <7> [174.460250] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3] <7> [174.460479] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] disconnected <6> [174.460700] [IGT] kms_addfb_basic: starting subtest too-high <7> [174.460777] i915 0000:00:02.0: [drm:intel_fill_fb_info [i915]] fb too big for bo (need 4198400 bytes, have 4194304 bytes) <7> [174.460984] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] could not create framebuffer <7> [174.461008] i915 0000:00:02.0: [drm:intel_fill_fb_info [i915]] fb too big for bo (need 4198400 bytes, have 4194304 bytes) <7> [174.461262] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] could not create framebuffer <7> [174.461299] i915 0000:00:02.0: [drm:intel_fill_fb_info [i915]] fb too big for bo (need 4198400 bytes, have 4194304 bytes) <7> [174.461506] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] could not create framebuffer <6> [174.461858] [IGT] kms_addfb_basic: exiting, ret=0 <7> [174.462108] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 2 to 0 or reprobing <7> [174.462118] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] <7> [174.462143] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1 <7> [174.462385] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0 <7> [174.462581] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug <7> [174.462963] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [174.463142] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [174.463588] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [174.463772] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [174.463780] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [174.463959] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [174.465489] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [174.465497] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [174.465678] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found] <7> [174.465860] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] status updated from connected to disconnected <7> [174.465882] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected <7> [174.466219] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <6> [174.493851] Console: switching to colour frame buffer device 170x48

Created at 2023-04-09 19:54:15