Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g94188a1dc (x86_64) (Linux: 6.3.0-rc5-linus-v6.3-rc5-g7e364e56293b+ x86_64)
Out 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.015s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.015s)
Dmesg
<6> [129.018172] Console: switching to colour dummy device 80x25
<6> [129.018562] [IGT] kms_force_connector_basic: executing
<7> [129.062486] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [129.063287] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [129.063603] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [129.064481] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [129.064495] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.064533] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [129.064840] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [129.065106] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [129.065606] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.065897] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.066374] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.066630] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.066641] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.066962] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.067957] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.067968] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.068356] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.068386] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.068397] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.068407] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.068417] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.068427] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.068490] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.068520] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [129.068802] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [129.069069] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [129.069548] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.069832] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.070258] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.070476] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.070482] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.070659] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.071570] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.071577] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.071901] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.071921] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.071927] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.071933] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.071938] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.071943] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.072001] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.072020] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [129.072206] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [129.072383] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [129.072753] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.072954] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.073311] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.073487] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.073493] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.073669] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.074565] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.074573] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.074879] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.074899] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.074905] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.074911] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.074916] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.074921] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [129.075280] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [129.075500] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 2 or reprobing
<7> [129.075509] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.075757] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.075969] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.076329] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.076522] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.076542] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.076744] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.077641] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.077655] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.077954] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.077974] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.077982] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.077988] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.077993] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.077999] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.078053] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.078276] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.078452] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.078870] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.079048] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.079061] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.079238] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.080150] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.080164] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.080426] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.080446] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.080452] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.080457] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.080462] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.080468] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.080735] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:61:VGA-1] EDID override set
<7> [129.080779] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.080848] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [129.080855] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [129.080872] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [129.080877] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [129.080898] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [129.080903] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [129.081020] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.081027] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [129.081037] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.081043] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [129.081052] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.081070] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [129.081075] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [129.081080] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [129.081085] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.081091] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.081096] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.081320] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:61:VGA-1] EDID override set
<7> [129.081379] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.081456] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [129.081465] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [129.081473] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:61:VGA-1] EDID changed, epoch counter 8
<7> [129.081495] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [129.081501] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [129.081518] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [129.081524] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [129.081740] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [129.081752] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [129.081767] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.081795] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [129.081803] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [129.081811] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.081820] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.081829] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.082009] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:VGA-1] EDID override reset
<7> [129.082042] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.082266] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.082448] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.082809] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.082986] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.083000] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:61:VGA-1] EDID changed, epoch counter 9
<7> [129.083013] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.083190] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.084081] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.084096] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.084333] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [129.084341] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [129.084350] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [129.084356] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [129.084365] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.084383] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.084388] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.084394] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.084399] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.084404] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.084589] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 2 to 0 or reprobing
<7> [129.084596] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.084617] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [129.084868] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [129.085065] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [129.085444] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.085619] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.086012] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.086190] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.086196] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.086373] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.087270] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.087278] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.087530] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.087549] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.087556] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.087562] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.087567] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.087573] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.087620] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.087641] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [129.087875] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [129.088068] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [129.088441] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.088615] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.089010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.089187] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.089193] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.089369] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.090256] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.090263] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.090548] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.090568] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.090574] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.090579] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.090584] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.090589] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.090774] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [129.091309] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [129.091317] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.091338] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [129.091525] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [129.091703] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [129.092132] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.092309] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.092707] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.092920] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.092927] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.093168] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.094047] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.094055] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.094307] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.094327] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.094334] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.094340] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.094345] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.094351] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.094397] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.094418] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [129.094603] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [129.094802] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [129.095228] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.095403] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.095776] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.095954] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.095960] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.096136] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.097017] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.097024] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.097270] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.097289] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.097295] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.097300] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.097306] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.097311] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.097444] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:VGA-1] EDID override reset
<7> [129.097472] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.097492] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [129.097677] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [129.097874] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [129.098322] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.098496] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.098818] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.098995] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.099001] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.099177] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.100166] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.100174] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.100419] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.100438] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.100444] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.100449] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.100454] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.100459] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.100653] [drm:status_store] [CONNECTOR:64:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [129.100661] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [129.100681] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [129.101102] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.101279] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [129.101672] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.101887] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.101896] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.102089] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [129.102973] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.102981] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [129.103159] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [129.103218] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [129.103239] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [129.103612] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.103853] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [129.104227] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.104413] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.104419] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.104590] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [129.105484] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.105492] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [129.105669] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [129.106272] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:64:HDMI-A-1] EDID override reset
<7> [129.106302] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [129.106324] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [129.106731] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.106954] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [129.107310] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.107487] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.107492] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.107664] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [129.108569] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.108576] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [129.108775] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [129.109010] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:72:DP-1] EDID override reset
<7> [129.109039] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:72:DP-1]
<7> [129.109060] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:72:DP-1]
<7> [129.109250] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:72:DP-1] disconnected
<6> [129.110029] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [129.110222] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [129.110232] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [129.110258] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [129.110473] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [129.110650] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [129.111109] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.111285] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [129.111643] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [129.111859] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.111867] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.112089] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [129.112976] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [129.112985] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [129.113246] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [129.113266] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [129.113274] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [129.113280] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [129.113286] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [129.113291] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [129.113362] [drm:status_store] [CONNECTOR:64:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [129.113369] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [129.113389] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [129.113769] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.114026] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [129.114399] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [129.114576] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.114583] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [129.114816] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [129.115766] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [129.115778] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [129.115960] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [129.116296] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [129.147005] Console: switching to colour frame buffer device 128x48
Created at 2023-04-02 23:02:29