Results for igt@gem_exec_suspend@basic-s3@smem

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-g94188a1dc (x86_64) (Linux: 6.3.0-rc5-linus-v6.3-rc5-g7e364e56293b+ x86_64)
Out	Starting subtest: basic-S3 Starting dynamic subtest: smem [cmd] rtcwake: wakeup from "mem" using /dev/rtc0 at Sun Apr 2 21:54:35 2023 Dynamic subtest smem: SUCCESS (6.995s) Subtest basic-S3: SUCCESS (6.997s)
Err	Starting subtest: basic-S3 Starting dynamic subtest: smem Dynamic subtest smem: SUCCESS (6.995s) Subtest basic-S3: SUCCESS (6.997s)
Dmesg	<6> [539.253658] [IGT] gem_exec_suspend: executing <7> [539.288776] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [539.291080] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [539.292069] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [539.294355] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [539.298330] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <6> [539.330397] [IGT] gem_exec_suspend: starting subtest basic-S3 <6> [539.332171] [IGT] gem_exec_suspend: starting dynamic subtest smem <7> [539.345105] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [540.922932] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [540.932296] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [542.567519] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <6> [542.647744] PM: suspend entry (deep) <6> [542.672840] Filesystems sync: 0.025 seconds <6> [542.676605] Freezing user space processes <6> [542.688668] Freezing user space processes completed (elapsed 0.012 seconds) <6> [542.688717] OOM killer disabled. <6> [542.688733] Freezing remaining freezable tasks <6> [542.692207] Freezing remaining freezable tasks completed (elapsed 0.003 seconds) <6> [542.692448] printk: Suspending console(s) (use no_console_suspend to debug) <6> [542.707167] r8169 0000:03:00.0 enp3s0: Link is Down <5> [542.710442] sd 0:0:0:0: [sda] Synchronizing SCSI cache <5> [542.713176] sd 0:0:0:0: [sda] Stopping disk <7> [542.719801] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [542.720437] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling display <7> [542.721396] i915 0000:00:02.0: [drm:intel_vga_redisable_power_on [i915]] Something enabled VGA plane, disabling it <7> [542.722432] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [542.723062] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling dpio-common-bc <7> [542.723876] i915 0000:00:02.0: [drm:chv_dpio_cmn_power_well_enable [i915]] Enabled DPIO PHY0 (PHY_CONTROL=0x050007fd) <7> [542.725051] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling dpio-common-d <7> [542.725857] i915 0000:00:02.0: [drm:chv_dpio_cmn_power_well_enable [i915]] Enabled DPIO PHY1 (PHY_CONTROL=0x050007ff) <7> [542.726728] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [542.726797] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:102:HDMI-A-1] <7> [542.727684] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [542.728219] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [542.729065] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [542.729710] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [542.729733] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [542.730320] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [542.732974] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [542.733000] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [542.733629] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:102:HDMI-A-1] Same epoch counter 1 <7> [542.733752] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [542.734456] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [542.734547] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:111:HDMI-A-2] <7> [542.735386] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus panel] NAK for addr: 0050 w(1) <7> [542.735915] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus panel] NAK on first message, retry <7> [542.736721] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus panel] NAK for addr: 0050 w(1) <7> [542.737361] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus panel <7> [542.737385] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [542.737906] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus panel. force bit now 1 <7> [542.740561] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus panel <7> [542.740585] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus panel. force bit now 0 <7> [542.741144] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:111:HDMI-A-2] Same epoch counter 1 <7> [542.973928] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling dpio-common-d <7> [542.975551] i915 0000:00:02.0: [drm:chv_dpio_cmn_power_well_disable [i915]] Disabled DPIO PHY1 (PHY_CONTROL=0x050007fd) <7> [542.977193] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling dpio-common-bc <7> [542.978897] i915 0000:00:02.0: [drm:chv_dpio_cmn_power_well_disable [i915]] Disabled DPIO PHY0 (PHY_CONTROL=0x050007fc) <7> [542.980532] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling display <7> [542.982192] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [542.987181] i915 0000:00:02.0: [drm:vlv_suspend_complete [i915]] timeout waiting for GT wells to go off <6> [543.035555] ACPI: PM: Preparing to enter system sleep state S3 <6> [543.046747] ACPI: PM: Saving platform NVS memory <6> [543.047050] Disabling non-boot CPUs ... <6> [543.065157] smpboot: CPU 1 is now offline <6> [543.067624] ACPI: PM: Low-level resume complete <6> [543.067721] ACPI: PM: Restoring platform NVS memory <6> [543.068430] Enabling non-boot CPUs ... <6> [543.070148] x86: Booting SMP configuration: <6> [543.070169] smpboot: Booting Node 0 Processor 1 APIC 0x4 <6> [543.079063] CPU1 is up <6> [543.079452] ACPI: PM: Waking up from system sleep state S3 <7> [543.121047] i915 0000:00:02.0: [drm:intel_power_domains_init_hw [i915]] Initial PHY_CONTROL=0x050007fc <7> [543.123317] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [543.124082] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling display <7> [543.124938] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling dpio-common-bc <7> [543.125950] i915 0000:00:02.0: [drm:chv_dpio_cmn_power_well_enable [i915]] Enabled DPIO PHY0 (PHY_CONTROL=0x050007fd) <7> [543.127182] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling dpio-common-d <7> [543.128225] i915 0000:00:02.0: [drm:chv_dpio_cmn_power_well_enable [i915]] Enabled DPIO PHY1 (PHY_CONTROL=0x050007ff) <4> [543.133068] xhci_hcd 0000:00:14.0: xHC error in resume, USBSTS 0x411, Reinit <5> [543.133088] usb usb1: root hub lost power or was reset <5> [543.133098] usb usb2: root hub lost power or was reset <5> [543.135492] sd 0:0:0:0: [sda] Starting disk <7> [543.138487] i915 0000:00:02.0: [drm:intel_vga_redisable_power_on [i915]] Something enabled VGA plane, disabling it <7> [543.141054] i915 0000:00:02.0: [drm:intel_rps_enable [i915]] GPLL enabled? yes <7> [543.141794] i915 0000:00:02.0: [drm:intel_rps_enable [i915]] GPU status: 0x00002010 <7> [543.149506] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 266667 kHz, VCO 1600000 kHz, ref 0 kHz, bypass 0 kHz, voltage level 11 <7> [543.150841] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled <7> [543.151854] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled <7> [543.152836] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled <7> [543.153687] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:primary A] hw state readout: disabled, pipe A <7> [543.154484] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:sprite A] hw state readout: disabled, pipe A <7> [543.155484] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:41:sprite B] hw state readout: disabled, pipe A <7> [543.156441] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A <7> [543.157370] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:primary B] hw state readout: disabled, pipe B <7> [543.158224] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:56:sprite C] hw state readout: disabled, pipe B <7> [543.159105] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:62:sprite D] hw state readout: disabled, pipe B <7> [543.160782] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B <7> [543.161636] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:primary C] hw state readout: disabled, pipe C <7> [543.162420] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:77:sprite E] hw state readout: disabled, pipe C <7> [543.163929] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:83:sprite F] hw state readout: disabled, pipe C <7> [543.164837] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C <7> [543.165717] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DP B] hw state readout: disabled, pipe A <7> [543.166513] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:101:HDMI B] hw state readout: disabled, pipe A <7> [543.167422] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DP D] hw state readout: disabled, pipe A <7> [543.168285] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:110:HDMI D] hw state readout: disabled, pipe A <7> [543.169188] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:DP-1] hw state readout: disabled <7> [543.170142] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:102:HDMI-A-1] hw state readout: disabled <7> [543.171027] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:107:DP-2] hw state readout: disabled <7> [543.171908] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:111:HDMI-A-2] hw state readout: disabled <7> [543.172741] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:primary A] min_cdclk 0 kHz <7> [543.173487] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:sprite A] min_cdclk 0 kHz <7> [543.174333] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:41:sprite B] min_cdclk 0 kHz <7> [543.175149] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz <7> [543.175994] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0 <7> [543.176819] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:primary B] min_cdclk 0 kHz <7> [543.177551] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:56:sprite C] min_cdclk 0 kHz <7> [543.178418] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:62:sprite D] min_cdclk 0 kHz <7> [543.179228] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz <7> [543.180068] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [543.180912] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:primary C] min_cdclk 0 kHz <7> [543.181751] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:77:sprite E] min_cdclk 0 kHz <7> [543.182510] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:83:sprite F] min_cdclk 0 kHz <7> [543.183358] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz <7> [543.184173] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [543.185090] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state] <7> [543.185930] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state] <7> [543.186770] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state] <7> [543.192733] i915 0000:00:02.0: [drm:vlv_wm_get_hw_state [i915]] Punit not acking DDR DVFS request, assuming DDR DVFS is disabled <7> [543.193369] i915 0000:00:02.0: [drm:vlv_wm_get_hw_state [i915]] Initial watermarks: pipe A, plane=15, cursor=15, sprite0=15, sprite1=15 <7> [543.194108] i915 0000:00:02.0: [drm:vlv_wm_get_hw_state [i915]] Initial watermarks: pipe B, plane=15, cursor=15, sprite0=15, sprite1=15 <7> [543.194818] i915 0000:00:02.0: [drm:vlv_wm_get_hw_state [i915]] Initial watermarks: pipe C, plane=15, cursor=15, sprite0=15, sprite1=15 <7> [543.195432] i915 0000:00:02.0: [drm:vlv_wm_get_hw_state [i915]] Initial watermarks: SR plane=127, SR cursor=0 level=0 cxsr=0 <7> [543.196852] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset mismatch in cpu_transcoder (expected 0, found -1) <7> [543.197654] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:72:pipe B] fastset mismatch in cpu_transcoder (expected 1, found -1) <7> [543.198427] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:93:pipe C] fastset mismatch in cpu_transcoder (expected 2, found -1) <7> [543.199419] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change <7> [543.200261] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 200000 kHz, actual 200000 kHz <7> [543.201108] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 15, actual 15 <7> [543.202040] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [modeset] <7> [543.202875] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:primary A] fb: [NOFB], visible: no <7> [543.203710] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:35:sprite A] fb: [NOFB], visible: no <7> [543.204498] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:41:sprite B] fb: [NOFB], visible: no <7> [543.205356] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no <7> [543.206198] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [modeset] <7> [543.207050] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:52:primary B] fb: [NOFB], visible: no <7> [543.207919] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:56:sprite C] fb: [NOFB], visible: no <7> [543.208760] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:62:sprite D] fb: [NOFB], visible: no <7> [543.209535] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:68:cursor B] fb: [NOFB], visible: no <7> [543.210417] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [modeset] <7> [543.211261] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:73:primary C] fb: [NOFB], visible: no <7> [543.212115] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:77:sprite E] fb: [NOFB], visible: no <7> [543.212972] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:83:sprite F] fb: [NOFB], visible: no <7> [543.213807] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:89:cursor C] fb: [NOFB], visible: no <7> [543.215121] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 200000 kHz, VCO 1600000 kHz, ref 0 kHz, bypass 0 kHz, voltage level 15 <7> [543.216384] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:DP B] <7> [543.217211] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:101:HDMI B] <7> [543.218042] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DP D] <7> [543.218884] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:110:HDMI D] <7> [543.219715] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:95:DP-1] <7> [543.220547] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:102:HDMI-A-1] <7> [543.221444] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:107:DP-2] <7> [543.222330] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:111:HDMI-A-2] <7> [543.223236] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A] <7> [543.224126] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:72:pipe B] <7> [543.225014] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:93:pipe C] <7> [543.227055] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [543.227682] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected <7> [543.227978] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [543.228069] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:102:HDMI-A-1] <7> [543.228777] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling dpio-common-d <7> [543.229759] i915 0000:00:02.0: [drm:chv_dpio_cmn_power_well_disable [i915]] Disabled DPIO PHY1 (PHY_CONTROL=0x050007fd) <7> [543.230658] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling dpio-common-bc <7> [543.231519] i915 0000:00:02.0: [drm:chv_dpio_cmn_power_well_disable [i915]] Disabled DPIO PHY0 (PHY_CONTROL=0x050007fc) <7> [543.232462] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling display <7> [543.233794] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [543.234741] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [543.235465] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling display <7> [543.237219] i915 0000:00:02.0: [drm:intel_vga_redisable_power_on [i915]] Something enabled VGA plane, disabling it <7> [543.238716] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [543.239425] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [543.240453] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [543.241300] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [543.241331] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [543.242152] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [543.248320] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [543.248356] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [543.249320] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling display <7> [543.250992] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [543.252183] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:102:HDMI-A-1] Same epoch counter 1 <7> [543.252360] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [543.253366] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [543.254566] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling display <7> [543.256279] i915 0000:00:02.0: [drm:intel_vga_redisable_power_on [i915]] Something enabled VGA plane, disabling it <7> [543.258022] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling display <7> [543.259348] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [543.260689] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [543.260870] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:111:HDMI-A-2] <7> [543.261867] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [543.262846] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling display <7> [543.264472] i915 0000:00:02.0: [drm:intel_vga_redisable_power_on [i915]] Something enabled VGA plane, disabling it <7> [543.266534] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus panel] NAK for addr: 0050 w(1) <7> [543.267462] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus panel] NAK on first message, retry <7> [543.268767] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus panel] NAK for addr: 0050 w(1) <7> [543.269710] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus panel <7> [543.269840] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [543.270706] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus panel. force bit now 1 <7> [543.274278] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus panel <7> [543.274309] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus panel. force bit now 0 <7> [543.275133] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling display <7> [543.276275] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <6> [543.276817] r8169 0000:03:00.0 enp3s0: Link is Down <7> [543.278483] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:111:HDMI-A-2] Same epoch counter 1 <6> [543.432298] usb 1-5: reset high-speed USB device number 2 using xhci_hcd <6> [543.446859] ata2: SATA link down (SStatus 4 SControl 300) <6> [543.446920] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) <6> [543.487139] ata1.00: configured for UDMA/133 <6> [543.497631] ahci 0000:00:13.0: port does not support device sleep <6> [543.856299] usb 1-5.1: reset full-speed USB device number 3 using xhci_hcd <6> [543.963004] OOM killer enabled. <6> [543.963022] Restarting tasks ... done. <5> [543.978726] random: crng reseeded on system resumption <6> [543.980080] PM: suspend exit <6> [544.014545] Bluetooth: hci0: Legacy ROM 2.5 revision 1.0 build 3 week 17 2014 <6> [544.014640] Bluetooth: hci0: Intel device is already patched. patch num: 32 <7> [544.015568] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [544.031318] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [544.048999] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [546.324326] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [546.432959] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <6> [546.456901] [IGT] gem_exec_suspend: exiting, ret=0 <7> [546.458265] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

Created at 2023-04-02 23:02:30