Results for igt@kms_addfb_basic@bo-too-small

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-gacc698f96 (x86_64) (Linux: 6.3.0-rc4-linus-v6.3-rc4-g197b6b60ae7b+ x86_64)
Out 
Starting subtest: bo-too-small
Subtest bo-too-small: SUCCESS (0.000s)
Err 
Starting subtest: bo-too-small
Subtest bo-too-small: SUCCESS (0.000s)
Dmesg
<6> [81.337723] Console: switching to colour dummy device 80x25
<6> [81.337776] [IGT] kms_addfb_basic: executing
<7> [81.342054] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [81.342498] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [81.342631] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [81.342834] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] bad framebuffer format .... little-endian (0x00000000)
<7> [81.342936] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:123]
<7> [81.346155] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]
<7> [81.346173] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [81.346557] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.346670] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [81.346969] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.347096] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.347100] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.347209] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [81.350019] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.350024] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [81.350138] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [81.350809] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1]
<7> [81.350823] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-1]
<7> [81.350956] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1] disconnected
<7> [81.351477] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3]
<7> [81.351494] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [81.351822] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.351934] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [81.352242] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.352396] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.352400] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.352509] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [81.355310] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.355315] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [81.355429] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [81.355929] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]
<7> [81.355942] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [81.356286] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.356424] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [81.356723] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.356850] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.356853] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.356962] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [81.359775] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.359780] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [81.359894] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [81.359920] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:104:HDMI-A-2]
<7> [81.359933] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:104:HDMI-A-2]
<7> [81.372996] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD monitor Dummy #4B
<7> [81.373001] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD size 32, SAD count 0
<7> [81.373233] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [81.373374] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [81.373673] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [81.373800] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [81.374005] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:104:HDMI-A-2] probed modes :
<7> [81.374018] [drm:drm_mode_debug_printmodeline] Modeline "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9
<7> [81.374022] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 140000 1920 2068 2100 2101 1080 1082 1087 1115 0x40 0x9
<7> [81.374026] [drm:drm_mode_debug_printmodeline] Modeline "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [81.374030] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [81.374033] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [81.374036] [drm:drm_mode_debug_printmodeline] Modeline "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [81.374040] [drm:drm_mode_debug_printmodeline] Modeline "1280x960": 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
<7> [81.374043] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [81.374046] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [81.374050] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [81.374053] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [81.374056] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [81.374077] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1]
<7> [81.374090] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-1]
<7> [81.374218] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1] disconnected
<7> [81.374261] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3]
<7> [81.374274] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [81.374647] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.374759] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [81.375057] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.375183] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.375187] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.375306] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [81.378131] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.378136] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [81.378260] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [81.378286] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2]
<7> [81.378299] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-2]
<7> [81.379037] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI E/PHY E: DPCD: 11 0a 82 01 00 03 01 01 02 00 00 00 00 00 00
<7> [81.379637] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI E/PHY E: DP branch: OUI 00-00-00 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [81.380464] i915 0000:00:02.0: [drm:drm_dp_read_downstream_info [drm_display_helper]] AUX A/DDI E/PHY E: DPCD DFP: 09
<7> [81.380476] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:118:DDI E/PHY E] MST support: port: no, sink: no, modparam: yes
<7> [81.380591] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [81.380705] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [81.380818] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<5> [81.386163] EDID block 0 is all zeroes
<7> [81.386167] i915 0000:00:02.0: [drm:connector_bad_edid] [CONNECTOR:119:DP-2] EDID is invalid:
<7> [81.386172] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.386174] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.386175] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.386177] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.386179] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.386180] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.386182] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.386183] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.386190] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] VRR capable: no
<7> [81.386319] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] DFP max bpc 8, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [81.387035] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.387151] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [81.387765] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2] probed modes :
<7> [81.387778] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x48 0xa
<7> [81.387783] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [81.387787] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [81.387791] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [81.387794] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<6> [81.387910] [IGT] kms_addfb_basic: starting subtest bo-too-small
<7> [81.387947] i915 0000:00:02.0: [drm:intel_fill_fb_info [i915]] fb too big for bo (need 4198400 bytes, have 4190208 bytes)
<7> [81.388077] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] could not create framebuffer
<7> [81.390256] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]
<7> [81.390271] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [81.390605] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.390719] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [81.391017] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.391143] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.391147] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.391268] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [81.394094] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.394099] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [81.394213] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [81.394849] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1]
<7> [81.394863] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-1]
<7> [81.394992] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1] disconnected
<7> [81.395441] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3]
<7> [81.395455] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [81.395782] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.395895] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [81.396192] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.396344] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.396348] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.396485] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [81.399302] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.399307] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [81.399421] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [81.399921] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]
<7> [81.399935] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [81.400269] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.400413] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [81.400712] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.400838] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.400841] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.400951] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [81.403752] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.403757] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [81.403870] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [81.403896] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:104:HDMI-A-2]
<7> [81.403908] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:104:HDMI-A-2]
<7> [81.417392] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD monitor Dummy #4B
<7> [81.417398] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD size 32, SAD count 0
<7> [81.417620] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [81.417736] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [81.418034] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [81.418160] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [81.418408] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:104:HDMI-A-2] probed modes :
<7> [81.418422] [drm:drm_mode_debug_printmodeline] Modeline "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9
<7> [81.418426] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 140000 1920 2068 2100 2101 1080 1082 1087 1115 0x40 0x9
<7> [81.418430] [drm:drm_mode_debug_printmodeline] Modeline "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [81.418434] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [81.418437] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [81.418440] [drm:drm_mode_debug_printmodeline] Modeline "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [81.418444] [drm:drm_mode_debug_printmodeline] Modeline "1280x960": 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
<7> [81.418447] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [81.418450] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [81.418454] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [81.418457] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [81.418460] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [81.418486] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1]
<7> [81.418500] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-1]
<7> [81.418630] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1] disconnected
<7> [81.418654] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3]
<7> [81.418667] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [81.418991] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.419101] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [81.419423] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.419568] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.419572] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.419681] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [81.422489] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.422494] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [81.422608] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [81.422634] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2]
<7> [81.422646] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-2]
<7> [81.423350] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI E/PHY E: DPCD: 11 0a 82 01 00 03 01 01 02 00 00 00 00 00 00
<7> [81.423928] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI E/PHY E: DP branch: OUI 00-00-00 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [81.424730] i915 0000:00:02.0: [drm:drm_dp_read_downstream_info [drm_display_helper]] AUX A/DDI E/PHY E: DPCD DFP: 09
<7> [81.424742] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:118:DDI E/PHY E] MST support: port: no, sink: no, modparam: yes
<7> [81.424857] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [81.424971] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [81.425082] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<5> [81.430447] EDID block 0 is all zeroes
<7> [81.430451] i915 0000:00:02.0: [drm:connector_bad_edid] [CONNECTOR:119:DP-2] EDID is invalid:
<7> [81.430455] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.430457] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.430459] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.430460] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.430462] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.430464] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.430465] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.430467] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.430474] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] VRR capable: no
<7> [81.430591] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] DFP max bpc 8, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [81.431257] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.431408] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [81.432009] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2] probed modes :
<7> [81.432022] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x48 0xa
<7> [81.432026] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [81.432030] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [81.432034] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [81.432037] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [81.434146] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]
<7> [81.434160] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [81.434502] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.434615] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [81.434913] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.435038] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.435042] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.435150] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [81.437950] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.437954] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [81.438068] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [81.438698] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1]
<7> [81.438712] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-1]
<7> [81.438840] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1] disconnected
<7> [81.439224] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3]
<7> [81.439245] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [81.439572] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.439683] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [81.439980] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.440106] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.440110] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.440220] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [81.443052] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.443056] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [81.443169] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [81.443679] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]
<7> [81.443693] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [81.444019] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.444131] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [81.444449] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [81.444575] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.444579] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.444687] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [81.447484] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.447488] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [81.447599] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [81.447625] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:104:HDMI-A-2]
<7> [81.447638] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:104:HDMI-A-2]
<7> [81.460906] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD monitor Dummy #4B
<7> [81.460911] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD size 32, SAD count 0
<7> [81.461132] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [81.461255] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [81.461554] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [81.461680] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [81.461880] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:104:HDMI-A-2] probed modes :
<7> [81.461892] [drm:drm_mode_debug_printmodeline] Modeline "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9
<7> [81.461897] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 140000 1920 2068 2100 2101 1080 1082 1087 1115 0x40 0x9
<7> [81.461901] [drm:drm_mode_debug_printmodeline] Modeline "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [81.461904] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [81.461908] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [81.461911] [drm:drm_mode_debug_printmodeline] Modeline "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [81.461914] [drm:drm_mode_debug_printmodeline] Modeline "1280x960": 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
<7> [81.461918] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [81.461921] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [81.461924] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [81.461928] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [81.461931] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [81.461952] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1]
<7> [81.461965] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-1]
<7> [81.462092] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-1] disconnected
<7> [81.462116] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3]
<7> [81.462128] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [81.462469] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.462580] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [81.462877] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.463003] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.463007] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.463115] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [81.465911] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.465915] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [81.466028] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [81.466053] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2]
<7> [81.466065] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-2]
<7> [81.466762] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI E/PHY E: DPCD: 11 0a 82 01 00 03 01 01 02 00 00 00 00 00 00
<7> [81.467337] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI E/PHY E: DP branch: OUI 00-00-00 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [81.468133] i915 0000:00:02.0: [drm:drm_dp_read_downstream_info [drm_display_helper]] AUX A/DDI E/PHY E: DPCD DFP: 09
<7> [81.468144] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:118:DDI E/PHY E] MST support: port: no, sink: no, modparam: yes
<7> [81.468269] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [81.468383] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [81.468495] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<5> [81.473812] EDID block 0 is all zeroes
<7> [81.473815] i915 0000:00:02.0: [drm:connector_bad_edid] [CONNECTOR:119:DP-2] EDID is invalid:
<7> [81.473819] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.473821] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.473823] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.473825] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.473826] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.473828] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.473829] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.473831] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.473837] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] VRR capable: no
<7> [81.473952] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] DFP max bpc 8, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [81.474623] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [81.474738] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [81.475338] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2] probed modes :
<7> [81.475351] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x48 0xa
<7> [81.475355] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [81.475359] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [81.475363] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [81.475366] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [81.475655] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:122]
<7> [81.475703] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:122]
<6> [81.475809] [IGT] kms_addfb_basic: exiting, ret=0
<7> [81.476052] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [81.527574] Console: switching to colour frame buffer device 80x30
Created at 2023-03-26 23:09:29