Results for igt@kms_addfb_basic@bo-too-small-due-to-tiling

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gacc698f96 (x86_64) (Linux: 6.3.0-rc4-linus-v6.3-rc4-g197b6b60ae7b+ x86_64)
Out	Starting subtest: bo-too-small-due-to-tiling Subtest bo-too-small-due-to-tiling: SUCCESS (0.000s)
Err	Starting subtest: bo-too-small-due-to-tiling Subtest bo-too-small-due-to-tiling: SUCCESS (0.000s)
Dmesg	<6> [100.607272] [IGT] kms_addfb_basic: executing <7> [100.610927] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [100.611637] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [100.611853] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [100.612201] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] bad framebuffer format .... little-endian (0x00000000) <7> [100.612352] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:118] <7> [100.617841] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [100.617866] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [100.618080] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.618621] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [100.619201] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [100.619772] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [100.620510] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [100.620731] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [100.621636] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.623291] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.624940] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.626456] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.628317] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.630105] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.631855] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.633677] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.635294] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.636172] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [100.637157] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [100.637873] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [100.638401] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [100.638728] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [100.638956] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [100.639135] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [100.639788] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.640080] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [100.641174] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [100.641200] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [100.641458] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.642047] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.642329] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [100.643188] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [100.643216] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [100.643398] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.694642] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [100.710576] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [100.710585] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [100.710761] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [100.726128] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [100.726135] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [100.726307] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.726528] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [100.727214] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [100.727236] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [100.727451] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.727984] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [100.728588] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [100.729184] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [100.729891] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [100.730095] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [100.730999] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.732446] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.733794] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.735498] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.737289] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.739045] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.740782] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.742649] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.744248] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.745133] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [100.745997] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [100.746636] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [100.747124] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [100.747343] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [100.747580] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [100.747791] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [100.748446] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.748728] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [100.748778] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [100.748796] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [100.749000] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.749522] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.749726] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [100.749765] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [100.749784] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [100.749956] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.801653] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [100.817576] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [100.817585] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [100.817761] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [100.833593] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [100.833600] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [100.833772] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.833965] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <6> [100.834188] [IGT] kms_addfb_basic: starting subtest bo-too-small-due-to-tiling <7> [100.834324] i915 0000:00:02.0: [drm:intel_fill_fb_info [i915]] fb too big for bo (need 4194304 bytes, have 4190208 bytes) <7> [100.834617] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] could not create framebuffer <7> [100.840291] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [100.840326] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [100.840660] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.841277] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [100.841903] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [100.842493] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [100.843324] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [100.843643] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [100.844657] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.846307] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.847959] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.849453] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.851373] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.853214] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.855056] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.856881] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.858453] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.859344] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [100.860269] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [100.860981] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [100.861507] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [100.861753] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [100.861940] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [100.862137] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [100.862864] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.863094] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [100.863905] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [100.863928] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [100.864153] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.864675] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.864880] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [100.865746] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [100.865768] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [100.865950] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.917647] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [100.933651] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [100.933660] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [100.933839] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [100.949672] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [100.949678] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [100.949851] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.950044] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [100.950711] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [100.950733] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [100.950941] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.951475] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [100.952041] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [100.952649] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [100.953455] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [100.953702] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [100.954608] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.956208] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.957881] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.959447] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.961208] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.963014] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.964792] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.966617] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.968258] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [100.969154] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [100.970136] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [100.970857] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [100.971383] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [100.971728] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [100.972016] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [100.972294] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [100.973050] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.973348] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [100.973432] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [100.973461] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [100.973740] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [100.974305] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [100.974618] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [100.974677] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [100.974704] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [100.974942] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [101.025647] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [101.041572] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [101.041582] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [101.041757] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [101.057125] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [101.057132] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [101.057303] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [101.057532] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [101.061674] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [101.061697] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [101.061905] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [101.062435] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [101.062988] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [101.063603] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [101.064375] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [101.064635] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [101.065459] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.067160] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.068802] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.070451] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.072208] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.073974] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.075747] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.077453] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.079075] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.079991] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [101.080848] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [101.081460] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [101.081967] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [101.082182] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [101.082366] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [101.082576] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [101.083309] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [101.083599] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [101.084426] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [101.084456] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [101.084739] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [101.085339] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [101.085636] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [101.086566] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [101.086597] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [101.086782] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [101.137545] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [101.155087] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [101.155100] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [101.155385] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [101.172440] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [101.172449] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [101.172717] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [101.173017] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [101.173844] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [101.173869] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [101.174096] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [101.174722] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [101.175305] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [101.175929] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [101.176759] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [101.177049] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [101.178010] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.179652] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.181311] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.182962] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.184822] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.186745] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.188453] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.190227] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.191867] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [101.192677] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [101.193578] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [101.194278] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [101.194808] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [101.195101] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [101.195387] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [101.195683] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [101.196437] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [101.196734] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [101.196803] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [101.196832] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [101.197109] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [101.197725] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [101.198018] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [101.198076] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [101.198103] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [101.198339] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [101.249641] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [101.265569] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [101.265577] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [101.265752] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [101.281112] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [101.281119] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [101.281290] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [101.281505] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [101.282203] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:118] <7> [101.282318] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:118] <6> [101.282491] [IGT] kms_addfb_basic: exiting, ret=0 <7> [101.282983] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

Created at 2023-03-26 23:09:29