Results for igt@kms_addfb_basic@bad-pitch-65536

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gacc698f96 (x86_64) (Linux: 6.3.0-rc4-linus-v6.3-rc4-g197b6b60ae7b+ x86_64)
Out	Starting subtest: bad-pitch-65536 Subtest bad-pitch-65536: SUCCESS (0.000s)
Err	Starting subtest: bad-pitch-65536 Subtest bad-pitch-65536: SUCCESS (0.000s)
Dmesg	<6> [95.924910] [IGT] kms_addfb_basic: executing <7> [95.929033] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [95.929979] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [95.930339] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [95.930909] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] bad framebuffer format .... little-endian (0x00000000) <7> [95.931130] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:118] <6> [95.931402] [IGT] kms_addfb_basic: starting subtest bad-pitch-65536 <7> [95.931551] i915 0000:00:02.0: [drm:intel_fill_fb_info [i915]] fb too big for bo (need 33554432 bytes, have 4194304 bytes) <7> [95.931869] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] could not create framebuffer <7> [95.940167] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [95.940205] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [95.940761] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [95.941403] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [95.942165] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [95.942962] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [95.943863] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [95.944168] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [95.945233] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [95.946872] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [95.948384] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [95.949953] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [95.951704] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [95.953446] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [95.955192] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [95.956947] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [95.958453] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [95.959350] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [95.960316] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [95.961041] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [95.961561] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [95.961891] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [95.962178] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [95.962471] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [95.963221] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [95.963541] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [95.964725] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [95.964756] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [95.965050] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [95.965680] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [95.965977] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [95.967036] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [95.967066] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [95.967347] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.018643] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [96.035702] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.035713] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [96.035987] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [96.053037] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.053047] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [96.053318] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.053631] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [96.054434] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [96.054465] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [96.054752] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.055364] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [96.055964] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [96.056590] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [96.057462] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [96.057754] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [96.058791] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.060400] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.062013] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.063651] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.065455] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.067320] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.069156] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.070961] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.072453] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.073346] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [96.074279] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [96.074980] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [96.075509] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [96.075835] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [96.076120] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [96.076399] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [96.077155] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.077453] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [96.077525] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [96.077554] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [96.077832] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.078456] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.078750] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [96.078808] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [96.078835] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [96.079108] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.130650] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [96.147674] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.147685] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [96.147868] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [96.163237] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.163244] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [96.163438] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.163726] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [96.167900] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [96.167923] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [96.168133] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.168669] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [96.169167] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [96.169794] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [96.170567] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [96.170796] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [96.171728] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.173349] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.174971] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.176453] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.178204] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.179952] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.181756] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.183456] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.185120] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.186014] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [96.186966] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [96.187657] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [96.188155] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [96.188378] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [96.188617] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [96.188856] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [96.189587] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.189795] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [96.190850] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [96.190882] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [96.191115] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.191662] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.191958] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [96.192731] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [96.192751] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [96.192983] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.244534] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [96.260539] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.260547] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [96.260725] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [96.276580] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.276587] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [96.276762] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.276957] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [96.277570] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [96.277601] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [96.277842] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.278351] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [96.278874] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [96.279493] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [96.280268] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [96.280490] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [96.281458] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.283041] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.284616] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.286071] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.287970] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.289791] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.291691] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.293452] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.295065] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.295979] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [96.296835] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [96.297462] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [96.297979] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [96.298196] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [96.298379] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [96.298583] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [96.299248] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.299563] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [96.299632] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [96.299660] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [96.299851] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.300352] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.300601] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [96.300658] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [96.300685] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [96.300959] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.352652] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [96.368642] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.368651] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [96.368830] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [96.384707] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.384714] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [96.384888] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.385083] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [96.389256] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [96.389280] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [96.389530] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.390098] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [96.390675] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [96.391230] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [96.392062] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [96.392359] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [96.393445] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.395060] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.396631] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.398302] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.400089] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.401863] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.403603] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.405401] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.407017] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.407897] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [96.408728] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [96.409440] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [96.409920] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [96.410159] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [96.410344] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [96.410572] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [96.411274] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.411556] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [96.412345] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [96.412364] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [96.412580] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.413131] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.413339] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [96.414162] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [96.414183] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [96.414362] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.465640] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [96.481601] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.481610] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [96.481788] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [96.497618] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.497625] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [96.497798] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.497991] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [96.498655] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [96.498687] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [96.498932] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.499478] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [96.499974] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [96.500598] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [96.501373] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [96.501636] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [96.502637] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.504251] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.505787] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.507399] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.509205] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.510956] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.512729] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.514327] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.515989] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [96.516870] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [96.517709] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [96.518378] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [96.518874] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [96.519137] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [96.519342] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [96.519554] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [96.520237] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.520547] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [96.520616] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [96.520644] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [96.520848] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.521360] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.521586] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [96.521643] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [96.521671] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [96.521891] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [96.573646] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [96.589605] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.589613] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [96.589790] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [96.605644] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [96.605651] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [96.605828] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [96.606022] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [96.606681] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:118] <7> [96.606783] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:118] <6> [96.606934] [IGT] kms_addfb_basic: exiting, ret=0 <7> [96.607334] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

Created at 2023-03-26 23:09:29