Results for igt@i915_selftest@live@sanitycheck

Result: Pass

git-log-oneline igt_runner0 run0 results0.json boot0 dmesg0

pstore0-1679868204_Panic_1

DetailValue
Igt-Version 
IGT-Version: 1.27.1-gacc698f96 (x86_64) (Linux: 6.3.0-rc4-linus-v6.3-rc4-g197b6b60ae7b+ x86_64)
Out 
Starting subtest: live
Starting dynamic subtest: sanitycheck
Dynamic subtest sanitycheck: SUCCESS (1.798s)
Err 
Starting subtest: live
Starting dynamic subtest: sanitycheck
Dynamic subtest sanitycheck: SUCCESS (1.798s)
Dmesg
<6> [345.094239] [IGT] i915_selftest: executing
<6> [345.114396] [IGT] i915_selftest: starting subtest live
<6> [345.115253] [IGT] i915_selftest: starting dynamic subtest sanitycheck
<6> [345.174804] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [345.174830] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [345.174836] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [345.174841] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [345.218566] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [345.218592] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [345.218597] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [345.218603] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [345.265319] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [345.265348] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [345.265354] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [345.265360] nvme 0000:02:00.0: [ 0] RxErr (First)
<5> [345.279622] Setting dangerous option live_selftests - tainting kernel
<7> [345.351104] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K
<7> [345.351554] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [345.351927] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH
<7> [345.352216] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a
<7> [345.352713] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [345.353280] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [345.353622] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 19200 kHz
<7> [345.354590] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001
<7> [345.354891] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001
<7> [345.355740] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [345.356079] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [345.356359] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M
<6> [345.356631] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [345.356642] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [345.357292] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [345.357331] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7
<7> [345.357685] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K
<7> [345.358430] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018
<7> [345.358831] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0
<7> [345.359175] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [345.359499] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [345.359815] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [345.369733] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583
<7> [345.370119] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [345.370439] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [345.370750] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [345.371093] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [345.371403] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [345.371707] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [345.371996] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [345.372282] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [345.372564] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [345.372829] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [345.373097] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [345.373463] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [345.373750] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [345.374062] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50
<7> [345.374442] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68
<7> [345.374792] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56
<7> [345.375176] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834
<7> [345.375514] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941
<7> [345.375854] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878
<7> [345.376236] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899
<7> [345.376599] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488
<7> [345.376932] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583
<7> [345.377290] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069
<7> [345.377628] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719
<7> [345.377952] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483
<7> [345.378303] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280
<7> [345.378658] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000
<7> [345.379013] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000
<7> [345.379374] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000
<7> [345.379715] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000
<7> [345.380056] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000
<7> [345.380387] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000
<7> [345.380732] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000
<7> [345.381110] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000
<7> [345.382173] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [345.382596] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228
<7> [345.382968] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [345.383382] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5)
<7> [345.383751] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [345.384130] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [345.384486] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812)
<7> [345.384836] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34)
<7> [345.385193] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [345.385542] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)
<7> [345.385907] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [345.386321] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78)
<7> [345.386684] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)
<7> [345.387041] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [345.387387] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [345.387724] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [345.388077] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [345.388423] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [345.388788] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [345.389172] i915 0000:00:02.0: [drm:intel_bios_init [i915]] port C trying to use the same DDC pin (0x3) as port A, disabling port A DVI/HDMI support
<7> [345.389529] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [345.389869] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [345.390237] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000
<7> [345.390572] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [345.390924] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0
<7> [345.391314] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000
<7> [345.391669] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [345.392006] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0
<7> [345.392361] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000
<7> [345.392706] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [345.393094] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [345.393475] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [345.393840] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [345.394215] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [345.394568] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [345.394908] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [345.395397] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [345.395809] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [345.396190] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [345.396675] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [345.397038] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [345.397383] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [345.397754] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [345.398120] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [345.398467] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [345.398832] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [345.399227] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [345.399593] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [345.399928] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [345.400289] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [345.400737] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [345.401232] i915 0000:00:02.0: [drm:intel_dmc_ucode_init [i915]] Loading i915/icl_dmc_ver1_09.bin
<6> [345.403493] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9)
<7> [345.404146] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [345.405141] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us
<7> [345.405510] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [345.405773] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [345.406045] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [345.406308] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [345.406574] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [345.406854] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [345.407191] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [345.407461] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [345.424381] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 3 display pipes available.
<6> [345.428352] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [345.428375] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [345.428381] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [345.428386] nvme 0000:02:00.0: [ 0] RxErr
<7> [345.429976] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [345.430784] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz
<7> [345.431173] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] Max dotclock rate: 1113600 kHz
<7> [345.431581] i915 0000:00:02.0: [drm:intel_bios_port_aux_ch [i915]] using AUX A for port A (VBT)
<7> [345.431954] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A]
<7> [345.437051] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [345.437436] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [345.437799] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [345.438363] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [345.438739] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [345.439103] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [345.439440] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [345.439775] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [345.440163] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [345.440526] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7> [345.440992] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0
<7> [345.441423] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [345.441746] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [345.442655] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [345.443060] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [345.443411] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [345.443844] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [345.444352] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [345.444941] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on
<7> [345.445318] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [345.445732] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [345.446645] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [345.447067] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [345.447409] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [345.651517] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00
<7> [345.652463] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001
<7> [345.653252] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6
<7> [345.654226] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [345.659879] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [345.661813] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [345.663406] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [345.665349] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [345.667299] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [345.669062] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [345.670664] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [345.672622] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [345.674074] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [345.674090] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [345.674098] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [345.674191] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [345.674576] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [345.674899] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] Performing OUI wait
<7> [345.687683] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none
<7> [345.688231] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] Connector eDP-1 backlight initialized, disabled, brightness 0/96000
<7> [345.688663] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [345.688991] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [345.689329] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [345.689889] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [345.690253] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [345.690774] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [345.691785] i915 0000:00:02.0: [drm:intel_bios_port_aux_ch [i915]] using AUX B for port B (VBT)
<7> [345.692188] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B]
<7> [345.692914] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [345.693277] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B]
<7> [345.693599] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x2 for port B (VBT)
<7> [345.694159] i915 0000:00:02.0: [drm:intel_bios_port_aux_ch [i915]] using AUX C for port C (platform default)
<7> [345.694532] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C]
<7> [345.694862] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Using DDC pin 0x3 for port C (VBT)
<7> [345.695317] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port D is not present
<7> [345.696436] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled
<7> [345.696913] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled
<7> [345.697393] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled
<7> [345.697739] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [345.698091] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
<7> [345.698431] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A
<7> [345.698779] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A
<7> [345.699156] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A
<7> [345.699514] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A
<7> [345.699854] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A
<7> [345.700211] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A
<7> [345.700554] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B
<7> [345.700884] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B
<7> [345.701280] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B
<7> [345.701639] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B
<7> [345.702000] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B
<7> [345.702358] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B
<7> [345.702702] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B
<7> [345.703056] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B
<7> [345.703393] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C
<7> [345.703742] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C
<7> [345.704130] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C
<7> [345.704486] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C
<7> [345.704825] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C
<7> [345.705182] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C
<7> [345.705521] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C
<7> [345.705859] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C
<7> [345.706249] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [345.706608] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [345.706939] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A
<7> [345.707289] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B
<7> [345.707618] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C
<7> [345.707953] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A
<7> [345.708310] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [345.708683] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [345.709072] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [345.709499] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled
<7> [345.709856] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled
<7> [345.710220] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled
<7> [345.710571] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled
<7> [345.710890] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [345.711252] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
<7> [345.711603] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz
<7> [345.711932] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz
<7> [345.712277] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz
<7> [345.712606] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz
<7> [345.712919] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz
<7> [345.713254] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz
<7> [345.713594] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [345.713965] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz
<7> [345.714324] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz
<7> [345.714655] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz
<7> [345.714980] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz
<7> [345.715311] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz
<7> [345.715636] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz
<7> [345.715984] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz
<7> [345.716354] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz
<7> [345.716692] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [345.717053] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz
<7> [345.717387] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz
<7> [345.717706] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz
<7> [345.718036] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz
<7> [345.718358] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz
<7> [345.718675] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz
<7> [345.719033] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz
<7> [345.719384] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz
<7> [345.719720] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [345.741724] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state]
<7> [345.742139] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state]
<7> [345.742477] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state]
<7> [345.742813] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [345.743464] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [345.743836] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [345.744632] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 1000] for use by error capture
<7> [345.744931] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [1000, 100000000]
<7> [345.745258] MCR Steering: Default steering: group=0x0, instance=0x0
<7> [345.745489] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global
<7> [345.748359] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 11 engine workarounds on rcs'0
<7> [345.748734] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0
<7> [345.749285] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0
<7> [345.752274] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0
<7> [345.754008] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0
<7> [345.756084] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0
<7> [345.773610] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping
<7> [345.773999] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping
<7> [345.774601] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping
<7> [345.774969] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [345.775554] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [345.777106] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [345.777441] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [345.777734] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [345.778040] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [345.786204] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered
<7> [345.786770] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [345.788892] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event
<7> [345.790308] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [345.792449] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event
<7> [345.793540] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event
<7> [345.794659] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event
<6> [345.794877] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [345.799608] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected
<6> [345.836156] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [345.845119] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input23
<6> [345.846087] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [345.846438] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x810 (init value 0x810)
<7> [345.846930] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4
<7> [345.848455] [drm:drm_client_modeset_probe]
<7> [345.848977] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]
<7> [345.849124] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [345.849499] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] status updated from unknown to disconnected
<6> [345.849576] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [345.849597] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [345.849602] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [345.849608] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [345.850106] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] disconnected
<7> [345.850140] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:239:eDP-1] EDID changed, epoch counter 2
<7> [345.850232] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]
<7> [345.850263] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [345.850615] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] status updated from unknown to disconnected
<7> [345.850644] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected
<7> [345.850671] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]
<7> [345.850700] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [345.851045] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected
<7> [345.851074] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [345.851102] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]
<7> [345.851130] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [345.851457] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected
<7> [345.851485] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [345.851511] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [345.851529] [drm:drm_client_modeset_probe] connector 239 enabled? no
<7> [345.851536] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [345.851541] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [345.851547] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [345.851774] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [345.851815] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [345.851859] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [345.851903] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [345.859330] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [345.859760] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11
<7> [345.859768] i915 device info: graphics version: 11
<7> [345.859772] i915 device info: media version: 11
<7> [345.859775] i915 device info: display version: 11
<7> [345.859779] i915 device info: gt: 0
<7> [345.859783] i915 device info: memory-regions: 21
<7> [345.859787] i915 device info: page-sizes: 211000
<7> [345.859790] i915 device info: platform: JASPERLAKE
<7> [345.859794] i915 device info: ppgtt-size: 36
<7> [345.859797] i915 device info: ppgtt-type: 2
<7> [345.859801] i915 device info: dma_mask_size: 39
<7> [345.859804] i915 device info: is_mobile: no
<7> [345.859808] i915 device info: is_lp: no
<7> [345.859812] i915 device info: require_force_probe: no
<7> [345.859815] i915 device info: is_dgfx: no
<7> [345.859819] i915 device info: has_64bit_reloc: yes
<7> [345.859822] i915 device info: has_64k_pages: no
<7> [345.859826] i915 device info: gpu_reset_clobbers_display: no
<7> [345.859830] i915 device info: has_reset_engine: yes
<7> [345.859833] i915 device info: has_3d_pipeline: yes
<7> [345.859837] i915 device info: has_4tile: no
<7> [345.859840] i915 device info: has_flat_ccs: no
<7> [345.859844] i915 device info: has_global_mocs: no
<7> [345.859847] i915 device info: has_gmd_id: no
<7> [345.859850] i915 device info: has_gt_uc: yes
<7> [345.859854] i915 device info: has_heci_pxp: no
<7> [345.859857] i915 device info: has_heci_gscfi: no
<7> [345.859861] i915 device info: has_guc_deprivilege: no
<7> [345.859864] i915 device info: has_l3_ccs_read: no
<7> [345.859868] i915 device info: has_l3_dpf: no
<7> [345.859871] i915 device info: has_llc: yes
<7> [345.859874] i915 device info: has_logical_ring_contexts: yes
<7> [345.859878] i915 device info: has_logical_ring_elsq: yes
<7> [345.859881] i915 device info: has_media_ratio_mode: no
<7> [345.859885] i915 device info: has_mslice_steering: no
<7> [345.859888] i915 device info: has_oa_bpc_reporting: no
<7> [345.859892] i915 device info: has_oa_slice_contrib_limits: no
<7> [345.859895] i915 device info: has_one_eu_per_fuse_bit: no
<7> [345.859899] i915 device info: has_pxp: no
<7> [345.859902] i915 device info: has_rc6: yes
<7> [345.859905] i915 device info: has_rc6p: no
<7> [345.859909] i915 device info: has_rps: yes
<7> [345.859912] i915 device info: has_runtime_pm: yes
<7> [345.859916] i915 device info: has_snoop: no
<7> [345.859919] i915 device info: has_coherent_ggtt: no
<7> [345.859922] i915 device info: tuning_thread_rr_after_dep: no
<7> [345.859926] i915 device info: unfenced_needs_alignment: no
<7> [345.859929] i915 device info: hws_needs_physical: no
<7> [345.859933] i915 device info: has_pooled_eu: no
<7> [345.859936] i915 device info: cursor_needs_physical: no
<7> [345.859940] i915 device info: has_cdclk_crawl: no
<7> [345.859943] i915 device info: has_cdclk_squash: no
<7> [345.859947] i915 device info: has_ddi: yes
<7> [345.859950] i915 device info: has_dp_mst: yes
<7> [345.859953] i915 device info: has_dsb: no
<7> [345.859957] i915 device info: has_fpga_dbg: yes
<7> [345.859960] i915 device info: has_gmch: no
<7> [345.859964] i915 device info: has_hotplug: yes
<7> [345.859967] i915 device info: has_hti: no
<7> [345.859971] i915 device info: has_ipc: yes
<7> [345.859974] i915 device info: has_modular_fia: no
<7> [345.859978] i915 device info: has_overlay: no
<7> [345.859981] i915 device info: has_psr: yes
<7> [345.859985] i915 device info: has_psr_hw_tracking: yes
<7> [345.859988] i915 device info: overlay_needs_physical: no
<7> [345.859991] i915 device info: supports_tv: no
<7> [345.859995] i915 device info: has_hdcp: no
<7> [345.859998] i915 device info: has_dmc: yes
<7> [345.860002] i915 device info: has_dsc: yes
<7> [345.860005] i915 device info: rawclk rate: 19200 kHz
<7> [345.860013] i915 device info: iommu: enabled
<7> [345.860018] i915 device info: available engines: 40403
<7> [345.860761] i915 device info: slice total: 1, mask=0001
<7> [345.860767] i915 device info: subslice total: 4
<7> [345.860771] i915 device info: slice0: 4 subslices, mask=0000000f
<7> [345.860775] i915 device info: EU total: 16
<7> [345.860779] i915 device info: EU per subslice: 4
<7> [345.860782] i915 device info: has slice power gating: yes
<7> [345.860786] i915 device info: has subslice power gating: yes
<7> [345.860789] i915 device info: has EU power gating: yes
<6> [345.860794] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [345.860799] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [345.860803] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<6> [345.860811] i915: Performing live selftests with st_random_seed=0x26df7721 st_timeout=500
<6> [345.860816] i915: Running sanitycheck
<6> [345.860820] i915: i915_live_sanitycheck() - ok!
<7> [345.860851] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [345.921687] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [345.978850] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [345.980273] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD off
<7> [345.980777] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [345.981861] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [345.982899] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [346.610674] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [346.611635] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<6> [346.631911] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [346.631937] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [346.631942] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [346.631947] nvme 0000:02:00.0: [ 0] RxErr (First)
<4> [346.660903] i915: probe of 0000:00:02.0 failed with error -25
<6> [346.765623] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [346.765649] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [346.765654] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [346.765660] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [346.830853] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [346.830877] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [346.830882] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [346.830887] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [346.853822] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [346.853846] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [346.853851] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [346.853857] nvme 0000:02:00.0: [ 0] RxErr (First)
Created at 2023-03-26 23:09:29