Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g0d4bf61a3 (x86_64) (Linux: 6.3.0-rc3-linus-v6.3-rc3-ge8d018dd0257+ x86_64)
Out 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.495s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.495s)
Dmesg
<6> [177.026119] Console: switching to colour dummy device 80x25
<6> [177.026354] [IGT] kms_force_connector_basic: executing
<7> [177.029828] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.030455] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [177.030647] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.031322] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [177.031329] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.031345] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.082924] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.100038] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.100045] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.100175] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [177.117054] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.117060] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [177.117166] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [177.117215] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.117233] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.167920] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.185041] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.185045] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.185147] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [177.202061] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.202064] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [177.202157] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [177.202223] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.202238] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.252924] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.270045] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.270050] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.270147] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [177.286066] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.286069] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [177.286162] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<6> [177.286443] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [177.286541] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [177.286545] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.286556] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.337925] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.355062] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.355074] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.355206] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [177.372020] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.372027] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [177.372119] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] status updated from disconnected to connected
<7> [177.372160] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [177.372169] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.372175] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.372178] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.372181] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.372183] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.372218] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.372232] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.422924] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.440059] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.440069] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.440192] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [177.457038] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.457044] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [177.457168] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [177.457180] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.457183] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.457186] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.457189] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.457191] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.457354] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:258:HDMI-A-1] EDID override set
<7> [177.457368] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.457378] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.457682] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD monitor IGT
<7> [177.457685] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD size 24, SAD count 0
<7> [177.508924] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.526057] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [177.526140] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.526147] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [177.526152] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.526157] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [177.526162] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [177.526177] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [177.526181] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [177.526184] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.526187] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.526191] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.526301] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:258:HDMI-A-1] EDID override reset
<7> [177.526377] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.526389] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.576935] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.594043] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.594052] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.594177] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [177.611047] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.611053] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [177.611143] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:258:HDMI-A-1] EDID changed, epoch counter 2
<7> [177.611184] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [177.611188] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [177.611193] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [177.611196] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [177.611200] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [177.611212] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.611214] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.611217] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.611220] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.611222] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.611352] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [177.611356] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.611372] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.662919] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.680065] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.680070] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.680169] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [177.697032] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.697035] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [177.697128] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] status updated from connected to disconnected
<7> [177.697140] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [177.697199] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.697214] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.747923] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.765018] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.765022] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.765124] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [177.781044] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.781047] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [177.781139] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [177.781274] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.781653] [drm:status_store] [CONNECTOR:236:eDP-1] force updated from 0 to 0 or reprobing
<7> [177.781657] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [177.781669] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [177.782517] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [177.782615] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [177.783249] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [177.783342] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [177.783434] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [177.783523] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [177.783633] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [177.783638] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [177.783641] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [177.783645] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [177.783657] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [177.783771] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.784562] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.784655] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.785336] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [177.785348] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [177.785353] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [177.785377] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [177.785390] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [177.786191] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [177.786305] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [177.786928] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [177.787026] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [177.787121] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [177.787213] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [177.787326] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [177.787332] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [177.787336] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [177.787339] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [177.787353] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [177.787463] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.788241] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.788336] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.788992] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [177.789004] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [177.789009] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [177.789100] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:236:eDP-1] EDID override reset
<7> [177.789115] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [177.789128] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [177.789912] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [177.790012] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [177.790616] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [177.790721] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [177.790817] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [177.790909] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [177.791014] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [177.791017] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [177.791020] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [177.791023] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [177.791033] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [177.791125] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.791897] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.791991] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.792636] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [177.792647] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [177.792651] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [177.792751] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:246:DP-1] EDID override reset
<7> [177.792766] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [177.792777] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [177.792950] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [177.793052] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [177.793056] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.793066] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.843903] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.861030] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.861035] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.861157] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [177.878027] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.878031] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [177.878131] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [177.878178] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.878194] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.928924] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [177.946061] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.946066] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.946184] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [177.963044] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [177.963048] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [177.963139] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [177.963251] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:258:HDMI-A-1] EDID override reset
<7> [177.963270] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [177.963285] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [177.963909] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC4
<7> [177.964077] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC3
<7> [177.964289] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port G/TC#4: TC port mode reset (tbt-alt -> disconnected)
<7> [177.964290] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected)
<7> [177.964402] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC4
<7> [177.964522] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC3
<7> [178.013882] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [178.031080] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [178.031086] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [178.031206] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [178.048042] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [178.048046] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [178.048147] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [178.048276] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:264:DP-2] EDID override reset
<7> [178.048295] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2]
<7> [178.048310] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-2]
<7> [178.048426] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC3
<7> [178.048582] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC3
<7> [178.048701] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC3
<7> [178.048870] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port F/TC#3: PHY ownership not required (live status 00)
<7> [178.048976] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt)
<7> [178.049082] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC3
<7> [178.049232] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2] disconnected
<7> [178.049317] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:273:DP-3] EDID override reset
<7> [178.049329] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3]
<7> [178.049340] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-3]
<7> [178.049449] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC4
<7> [178.049598] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC4
<7> [178.049724] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC4
<7> [178.049875] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port G/TC#4: PHY ownership not required (live status 00)
<7> [178.049978] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port G/TC#4: TC port mode reset (disconnected -> tbt-alt)
<7> [178.050081] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC4
<7> [178.050228] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3] disconnected
<6> [178.050577] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [178.050657] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [178.050661] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [178.050672] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [178.102924] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [178.120029] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [178.120034] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [178.120131] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [178.136019] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [178.136022] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [178.136116] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [178.136179] [drm:status_store] [CONNECTOR:236:eDP-1] force updated from 0 to 0 or reprobing
<7> [178.136184] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [178.136199] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [178.137007] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [178.137102] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [178.137727] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [178.137825] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [178.137920] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [178.138012] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [178.138116] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [178.138121] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [178.138124] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [178.138127] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [178.138139] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [178.138230] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [178.139001] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [178.139092] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [178.139759] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [178.139771] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [178.139776] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [178.139943] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [178.176589] Console: switching to colour frame buffer device 240x67
Created at 2023-03-19 22:01:28