Results for igt@kms_addfb_basic@bo-too-small-due-to-tiling

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gf9d49501e (x86_64) (Linux: 6.3.0-rc2-linus-v6.3-rc2-geeac8ede1755+ x86_64)
Out	Starting subtest: bo-too-small-due-to-tiling Subtest bo-too-small-due-to-tiling: SUCCESS (0.000s)
Err	Starting subtest: bo-too-small-due-to-tiling Subtest bo-too-small-due-to-tiling: SUCCESS (0.000s)
Dmesg	<6> [85.723597] Console: switching to colour dummy device 80x25 <6> [85.723671] [IGT] kms_addfb_basic: executing <7> [85.766356] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [85.766767] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [85.766938] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [85.767195] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] bad framebuffer format .... little-endian (0x00000000) <7> [85.767343] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:91] <7> [85.771848] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] <7> [85.771874] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:79:HDMI-A-1] <7> [85.772184] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.772328] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [85.772661] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.772809] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.772815] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [85.772949] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [85.774421] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.774428] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [85.774571] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] disconnected <7> [85.775101] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] <7> [85.775180] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:87:DP-1] <7> [85.775349] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] disconnected <7> [85.775682] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] <7> [85.775699] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1 <7> [85.775848] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1 <7> [85.775986] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug <7> [85.776419] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [85.776557] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [85.776874] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [85.777029] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [85.777034] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [85.777246] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [85.778642] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [85.778648] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [85.778865] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes : <7> [85.778880] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [85.778886] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [85.778891] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 <7> [85.778896] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 <7> [85.778900] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [85.778922] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] <7> [85.778938] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:79:HDMI-A-1] <7> [85.779252] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.779394] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [85.779691] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.779833] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.779838] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [85.779976] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [85.781399] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.781405] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [85.781548] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] disconnected <7> [85.781584] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] <7> [85.781600] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:87:DP-1] <7> [85.781753] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] disconnected <6> [85.781911] [IGT] kms_addfb_basic: starting subtest bo-too-small-due-to-tiling <7> [85.781979] i915 0000:00:02.0: [drm:intel_fill_fb_info [i915]] fb too big for bo (need 4194304 bytes, have 4190208 bytes) <7> [85.782187] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] could not create framebuffer <7> [85.785578] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] <7> [85.785597] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:79:HDMI-A-1] <7> [85.785953] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.786095] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [85.786490] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.786637] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.786642] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [85.786776] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [85.788242] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.788248] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [85.788396] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] disconnected <7> [85.788969] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] <7> [85.788986] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:87:DP-1] <7> [85.789184] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] disconnected <7> [85.789470] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] <7> [85.789486] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1 <7> [85.789641] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1 <7> [85.789785] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug <7> [85.790146] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [85.790288] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [85.790617] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [85.790762] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [85.790767] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [85.790906] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [85.792370] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [85.792376] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [85.792581] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes : <7> [85.792596] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [85.792602] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [85.792607] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 <7> [85.792611] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 <7> [85.792615] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [85.792637] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] <7> [85.792653] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:79:HDMI-A-1] <7> [85.792996] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.793167] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [85.793520] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.793661] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.793665] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [85.793802] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [85.795276] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.795282] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [85.795427] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] disconnected <7> [85.795461] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] <7> [85.795477] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:87:DP-1] <7> [85.795630] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] disconnected <7> [85.798774] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] <7> [85.798793] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:79:HDMI-A-1] <7> [85.799174] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.799326] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [85.799654] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.799794] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.799800] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [85.799937] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [85.801376] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.801382] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [85.801533] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] disconnected <7> [85.802035] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] <7> [85.802052] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:87:DP-1] <7> [85.802247] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] disconnected <7> [85.802570] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] <7> [85.802586] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:76:VGA-1] force=1 <7> [85.802734] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1 <7> [85.802871] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug <7> [85.803211] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [85.803365] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [85.803716] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [85.803853] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [85.803858] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [85.803993] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [85.805396] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [85.805402] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [85.805603] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:VGA-1] probed modes : <7> [85.805618] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [85.805624] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [85.805629] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 <7> [85.805633] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 <7> [85.805638] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [85.805659] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] <7> [85.805675] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:79:HDMI-A-1] <7> [85.805985] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.806176] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [85.806502] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [85.806643] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.806649] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [85.806786] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [85.808245] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [85.808252] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [85.808397] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:79:HDMI-A-1] disconnected <7> [85.808434] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] <7> [85.808450] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:87:DP-1] <7> [85.808617] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:87:DP-1] disconnected <7> [85.808986] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:91] <7> [85.809054] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:91] <6> [85.809205] [IGT] kms_addfb_basic: exiting, ret=0 <7> [85.809526] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <6> [85.855580] Console: switching to colour frame buffer device 128x48

Created at 2023-03-14 04:19:55