Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-gf9d49501e (x86_64) (Linux: 6.3.0-rc2-linus-v6.3-rc2-geeac8ede1755+ x86_64)
Out 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.519s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.519s)
Dmesg
<6> [185.168057] Console: switching to colour dummy device 80x25
<6> [185.168313] [IGT] kms_force_connector_basic: executing
<7> [185.170476] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [185.170918] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [185.171038] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [185.171534] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [185.171541] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [185.171557] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [185.223006] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [185.240147] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.240154] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [185.240257] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [185.257108] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.257112] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [185.257207] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [185.257257] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [185.257273] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [185.308019] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [185.325141] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.325146] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [185.325262] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [185.342092] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.342096] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [185.342196] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [185.342266] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [185.342282] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [185.393005] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [185.410125] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.410130] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [185.410235] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [185.427072] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.427076] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [185.427175] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<6> [185.427430] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [185.427544] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [185.427548] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [185.427561] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [185.479004] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [185.496072] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.496085] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [185.496220] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [185.513076] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.513084] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [185.513185] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] status updated from disconnected to connected
<7> [185.513229] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [185.513240] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [185.513245] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [185.513249] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [185.513252] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [185.513255] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [185.513296] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [185.513312] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [185.563999] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [185.581147] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.581159] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [185.581288] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [185.598138] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.598145] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [185.598279] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [185.598291] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [185.598295] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [185.598298] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [185.598301] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [185.598304] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [185.601006] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:258:HDMI-A-1] EDID override set
<7> [185.601027] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [185.601040] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [185.601393] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD monitor IGT
<7> [185.601397] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD size 24, SAD count 0
<7> [185.651993] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [185.669101] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [185.669190] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [185.669196] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [185.669204] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [185.669208] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [185.669214] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [185.669228] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [185.669232] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [185.669236] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [185.669240] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [185.669243] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [185.669362] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:258:HDMI-A-1] EDID override reset
<7> [185.669450] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [185.669461] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [185.720006] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [185.737135] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.737147] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [185.737290] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [185.754135] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.754142] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [185.754239] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:258:HDMI-A-1] EDID changed, epoch counter 2
<7> [185.754279] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [185.754284] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [185.754289] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [185.754292] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [185.754297] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [185.754309] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [185.754313] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [185.754316] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [185.754318] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [185.754321] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [185.754477] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [185.754483] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [185.754500] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [185.765935] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [185.766123] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [185.776985] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [185.777236] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [185.827995] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [185.845130] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.845136] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [185.845258] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [185.862124] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.862129] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [185.862229] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] status updated from connected to disconnected
<7> [185.862242] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [185.862306] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [185.862322] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [185.913010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [185.930073] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.930078] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [185.930186] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [185.946119] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [185.946123] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [185.946223] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [185.946399] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [185.946832] [drm:status_store] [CONNECTOR:236:eDP-1] force updated from 0 to 0 or reprobing
<7> [185.946837] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [185.946851] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [185.947723] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [185.947848] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [185.948514] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [185.948610] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [185.948703] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [185.948807] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [185.948917] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [185.948922] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [185.948925] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [185.948929] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [185.948943] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [185.949038] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [185.949829] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [185.949924] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [185.950631] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [185.950643] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [185.950648] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [185.950681] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [185.950697] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [185.951546] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [185.951646] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [185.952293] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [185.952383] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [185.952474] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [185.952568] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [185.952675] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [185.952679] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [185.952683] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [185.952686] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [185.952697] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [185.952795] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [185.953600] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [185.953698] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [185.954384] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [185.954396] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [185.954400] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [185.954494] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:236:eDP-1] EDID override reset
<7> [185.954510] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [185.954521] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [185.955340] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [185.955436] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [185.956129] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [185.956222] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [185.956314] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [185.956406] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [185.956508] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [185.956512] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [185.956515] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [185.956518] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [185.956529] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [185.956620] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [185.957467] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [185.957559] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [185.958235] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [185.958246] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [185.958251] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [185.958357] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:246:DP-1] EDID override reset
<7> [185.958375] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [185.958389] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [185.958568] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [185.958684] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [185.958688] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [185.958699] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [185.969935] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [185.970110] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [185.980952] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [185.981129] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [186.032008] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [186.049140] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [186.049146] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [186.049266] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [186.066076] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [186.066081] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [186.066181] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [186.066235] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [186.066252] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [186.076971] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [186.077148] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [186.088004] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [186.088060] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC4
<7> [186.088282] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [186.088340] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC3
<7> [186.088614] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port G/TC#4: TC port mode reset (tbt-alt -> disconnected)
<7> [186.088617] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected)
<7> [186.088876] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC3
<7> [186.089107] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC4
<7> [186.140005] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [186.157123] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [186.157128] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [186.157250] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [186.174095] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [186.174099] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [186.174199] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [186.174331] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:258:HDMI-A-1] EDID override reset
<7> [186.174354] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [186.174371] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [186.225008] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [186.242131] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [186.242136] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [186.242242] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [186.259080] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [186.259084] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [186.259184] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [186.259317] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:264:DP-2] EDID override reset
<7> [186.259334] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2]
<7> [186.259346] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-2]
<7> [186.259457] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC3
<7> [186.259618] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC3
<7> [186.259744] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC3
<7> [186.259932] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port F/TC#3: PHY ownership not required (live status 00)
<7> [186.260043] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt)
<7> [186.260151] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC3
<7> [186.260303] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2] disconnected
<7> [186.260406] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:273:DP-3] EDID override reset
<7> [186.260421] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3]
<7> [186.260433] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-3]
<7> [186.260545] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC4
<7> [186.260700] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC4
<7> [186.260832] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_USBC4
<7> [186.260985] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port G/TC#4: PHY ownership not required (live status 00)
<7> [186.261090] i915 0000:00:02.0: [drm:intel_tc_port_update_mode [i915]] Port G/TC#4: TC port mode reset (disconnected -> tbt-alt)
<7> [186.261200] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_USBC4
<7> [186.261353] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3] disconnected
<6> [186.261744] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [186.261850] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [186.261855] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [186.261868] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [186.272964] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [186.273139] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [186.283971] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [186.284147] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [186.335002] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [186.352147] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [186.352152] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [186.352275] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [186.369135] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [186.369139] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [186.369240] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [186.369311] [drm:status_store] [CONNECTOR:236:eDP-1] force updated from 0 to 0 or reprobing
<7> [186.369317] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [186.369334] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [186.370215] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [186.370314] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [186.370972] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [186.371065] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [186.371158] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [186.371254] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [186.371363] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [186.371368] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [186.371371] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [186.371375] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [186.371389] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [186.371481] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [186.372313] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [186.372410] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [186.373134] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [186.373146] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [186.373151] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [186.373330] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [186.393863] Console: switching to colour frame buffer device 240x67
Created at 2023-03-14 04:19:56