igt@i915_pm_rpm@basic-pci-d3-state on bat-adls-5@linus-v6.3-rc2 Test details

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gf9d49501e (x86_64) (Linux: 6.3.0-rc2-linus-v6.3-rc2-geeac8ede1755+ x86_64)
Out	Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_client_modeset_commit_atomic+0x234/0x280 drm_client_modeset_commit_locked+0x56/0x190 drm_client_modeset_commit+0x23/0x50 __drm_fb_helper_restore_fbdev_mode_unlocked+0x99/0xd0 [drm_kms_helper] intel_fbdev_restore_mode+0x2f/0x60 [i915] Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xb26/0xe40 [i915] intel_atomic_commit+0x380/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 1 Wakeref x1 taken at: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] __intel_display_power_put_async+0x38/0x120 [i915] hsw_get_pipe_config+0x14f/0xcc0 [i915] intel_crtc_get_pipe_config+0x1f/0x50 [i915] intel_modeset_verify_crtc+0xc5/0x3a0 [i915] intel_atomic_commit_tail+0x8ef/0xe40 [i915] intel_atomic_commit+0x380/0x400 [i915] drm_atomic_commit+0x92/0xc0 Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (4.417s)
Err	Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (4.417s)
Dmesg	<6> [208.244661] Console: switching to colour dummy device 80x25 <6> [208.244935] [IGT] i915_pm_rpm: executing <7> [208.247588] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [208.247959] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] <7> [208.247974] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1] <7> [208.248761] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [208.248864] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [208.249429] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [208.249524] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [208.249613] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000 <7> [208.249696] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [208.249793] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz <7> [208.249799] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [208.249802] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41 <7> [208.249805] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0 <7> [208.249818] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes <7> [208.249900] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [208.250648] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [208.250739] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [208.251378] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes : <7> [208.251389] [drm:drm_mode_debug_printmodeline] Modeline "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa <7> [208.251457] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] <7> [208.251467] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [208.251577] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] disconnected <7> [208.251641] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1] <7> [208.251650] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [208.251755] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1] disconnected <7> [208.251819] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] <7> [208.251828] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [208.251929] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected <7> [208.251992] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] <7> [208.252001] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [208.252104] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] disconnected <7> [208.252167] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2] <7> [208.252176] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [208.252277] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2] disconnected <7> [208.252370] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] <7> [208.252380] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [208.252492] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] disconnected <7> [208.258772] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] <7> [208.258786] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [208.258910] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] disconnected <7> [208.259345] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1] <7> [208.259355] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [208.259477] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1] disconnected <7> [208.259918] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] <7> [208.259927] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [208.260036] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected <7> [208.260524] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] <7> [208.260533] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [208.260643] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] disconnected <7> [208.261073] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2] <7> [208.261082] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [208.261189] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2] disconnected <7> [208.261641] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] <7> [208.261650] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [208.261752] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] disconnected <7> [208.262315] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] <7> [208.262325] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1] <7> [208.263089] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [208.263181] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [208.263770] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [208.263859] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [208.263947] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000 <7> [208.264036] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [208.264138] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz <7> [208.264143] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [208.264146] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41 <7> [208.264149] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0 <7> [208.264161] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes <7> [208.264247] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [208.265014] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [208.265105] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [208.265728] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes : <7> [208.265739] [drm:drm_mode_debug_printmodeline] Modeline "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa <7> [208.265757] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] <7> [208.265768] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [208.265881] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] disconnected <7> [208.265905] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1] <7> [208.265914] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [208.266022] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1] disconnected <7> [208.266044] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] <7> [208.266053] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [208.266159] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected <7> [208.266179] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] <7> [208.266188] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [208.266293] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] disconnected <7> [208.266340] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2] <7> [208.266349] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [208.266454] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2] disconnected <7> [208.266474] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] <7> [208.266483] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [208.266589] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] disconnected <7> [208.266751] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:284] <7> [209.292116] [drm:drm_mode_setcrtc] [CRTC:80:pipe A] <7> [209.292580] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.enable (expected 1, found 0) <7> [209.293490] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.active (expected 1, found 0) <7> [209.294213] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in cpu_transcoder (expected 0, found -1) <7> [209.294950] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in lane_count (expected 2, found 0) <7> [209.295348] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dp_m_n (expected tu 64 data 7654604/8388608 link 318941/524288, found tu 0, data 0/0 link 0/0) <7> [209.295457] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in output_types (expected 0x00000100, found 0x00000000) <7> [209.295555] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in framestart_delay (expected 1, found 0) <7> [209.295654] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hdisplay (expected 1920, found 0) <7> [209.295761] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_htotal (expected 2080, found 0) <7> [209.295859] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_start (expected 1920, found 0) <7> [209.295955] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_end (expected 2080, found 0) <7> [209.296051] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_start (expected 1968, found 0) <7> [209.296150] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_end (expected 2000, found 0) <7> [209.296248] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vdisplay (expected 1280, found 0) <7> [209.296358] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vtotal (expected 1317, found 0) <7> [209.296461] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_start (expected 1280, found 0) <7> [209.296561] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_end (expected 1317, found 0) <7> [209.296661] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_start (expected 1283, found 0) <7> [209.296762] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_end (expected 1293, found 0) <7> [209.296859] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hdisplay (expected 1920, found 0) <7> [209.296955] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_htotal (expected 2080, found 0) <7> [209.297051] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_start (expected 1920, found 0) <7> [209.297148] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_end (expected 2080, found 0) <7> [209.297245] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_start (expected 1968, found 0) <7> [209.297358] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_end (expected 2000, found 0) <7> [209.297459] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vdisplay (expected 1280, found 0) <7> [209.297560] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vtotal (expected 1317, found 0) <7> [209.297657] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_start (expected 1280, found 0) <7> [209.297753] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_end (expected 1317, found 0) <7> [209.297850] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_start (expected 1283, found 0) <7> [209.297946] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_end (expected 1293, found 0) <7> [209.298040] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pixel_multiplier (expected 1, found 0) <7> [209.298131] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.flags (2) (expected 2, found 0) <7> [209.298222] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.flags (8) (expected 8, found 0) <7> [209.298325] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pipe_bpp (expected 24, found 0) <7> [209.298427] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_clock (expected 164250, found 0) <7> [209.298525] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_clock (expected 164250, found 0) <7> [209.298616] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in port_clock (expected 270000, found 0) <7> [209.298712] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll.isra.0 [i915]] [CRTC:80:pipe A] releasing DPLL 0 <7> [209.298843] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0x3), mbus joined? no->no <7> [209.298947] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0x0, ddb (0 - 2048) -> (0 - 0), active pipes 0x1 -> 0x0 <7> [209.299064] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2006) -> ( 0 - 0), size 2006 -> 0 <7> [209.299157] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb (2006 - 2048) -> ( 0 - 0), size 42 -> 0 <7> [209.299247] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [209.299346] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 2, 3, 4, 6, 6, 8, 12, 0, 2, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [209.299440] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 16, 33, 49, 65, 97, 97, 129, 193, 30, 33, 47 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [209.299532] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 19, 38, 55, 73, 108, 108, 143, 214, 31, 38, 48 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [209.299621] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 0 num active planes 0 <7> [209.299726] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 12447 required 0 <7> [209.299828] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 14636 required 0 <7> [209.299933] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 15540 required 0 <7> [209.300036] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 16761 required 0 <7> [209.300136] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0 <7> [209.300235] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 0 <7> [209.300344] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 0 <7> [209.300466] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz <7> [209.300566] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0 <7> [209.300668] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: no [modeset] <7> [209.300769] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no <7> [209.300869] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [209.300969] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [209.301068] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [209.301171] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [209.301273] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no <7> [209.301474] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1 <7> [209.308699] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]] <7> [209.514520] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] set backlight PWM = 0 <7> [209.515913] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A <7> [209.527024] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000 <7> [209.526940] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turn panel power off <7> [209.527448] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - short <7> [209.527736] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power off time <7> [209.528460] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7> [209.582387] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [209.583051] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A <7> [209.583837] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [209.583833] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:235:DDI A/PHY A] <7> [209.584545] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:80:pipe A] <7> [209.585216] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0 <7> [209.585915] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI A/PHY A] <7> [209.586519] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:244:DDI TC1/PHY B] <7> [209.587041] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:253:DDI TC2/PHY C] <7> [209.587592] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:255:DP-MST A] <7> [209.588081] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:256:DP-MST B] <7> [209.588612] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:257:DP-MST C] <7> [209.589086] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:258:DP-MST D] <7> [209.589601] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:266:DDI TC3/PHY D] <7> [209.590073] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:270:DDI TC4/PHY E] <7> [209.590583] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:272:DP-MST A] <7> [209.591050] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:273:DP-MST B] <7> [209.591569] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:274:DP-MST C] <7> [209.592027] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:275:DP-MST D] <7> [209.592483] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:eDP-1] <7> [209.592934] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [209.593437] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [209.593907] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2 <7> [209.594394] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3 <7> [209.594891] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3 <7> [209.595461] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [209.596034] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A] <7> [209.596807] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [209.597293] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [209.597811] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [209.599642] [drm:drm_mode_setcrtc] [CRTC:131:pipe B] <7> [209.600134] [drm:drm_mode_setcrtc] [CRTC:182:pipe C] <7> [209.600548] [drm:drm_mode_setcrtc] [CRTC:233:pipe D] <7> [209.638655] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7> [209.638862] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long <7> [209.639234] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [209.639638] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A] <7> [209.802559] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [209.804859] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [209.811712] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [209.815174] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [209.816375] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.816530] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [209.816654] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.816774] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [209.816885] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.816990] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [209.817097] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.817209] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [209.817322] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.817448] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [209.817640] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [209.817929] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [209.818148] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.818322] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [209.818434] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [209.818619] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <6> [209.906460] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state <7> [209.916155] [drm:drm_mode_setcrtc] [CRTC:80:pipe A] <7> [209.927691] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [209.927934] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [209.928372] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [209.928853] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [209.929876] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [209.931026] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [209.931391] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [209.931872] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [209.933856] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [209.934115] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [209.949313] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [209.951596] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [209.951912] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [209.952688] [drm:drm_mode_setcrtc] [CRTC:131:pipe B] <7> [209.953957] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [209.956269] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [209.957402] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.957539] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [209.957659] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.957776] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [209.957892] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.958008] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [209.958122] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.958239] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [209.958361] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.958478] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [209.958608] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [209.958781] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [209.958941] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [209.959092] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [209.959198] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [209.959344] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [209.983498] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [209.983684] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [209.983984] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [209.984336] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [209.985067] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [209.985447] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [209.985716] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [209.986059] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [209.987677] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [209.987889] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [210.000910] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [210.003138] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [210.003261] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [210.004353] [drm:drm_mode_setcrtc] [CRTC:182:pipe C] <7> [210.004354] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1] <7> [210.005451] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [210.007810] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [210.008942] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.009065] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [210.009182] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.009296] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [210.009427] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.009539] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [210.009650] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.009762] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [210.009874] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.009984] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [210.010113] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [210.010424] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [210.010590] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.010759] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [210.010884] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [210.011037] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [210.035103] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [210.035416] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [210.035697] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [210.036030] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [210.036863] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [210.037693] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [210.037934] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [210.038252] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [210.039850] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [210.040044] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [210.055174] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [210.056401] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [210.056538] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [210.056669] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [210.057461] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [210.058647] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.058773] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [210.058892] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.059011] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [210.059128] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.059245] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [210.059372] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.059498] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [210.059618] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [210.059735] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [210.059840] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [210.060092] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD on <7> [210.060235] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [210.186944] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [210.187861] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [210.188909] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068 <7> [210.189680] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 panel power wasn't enabled <7> [210.223557] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7> [210.223984] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long <7> [210.224805] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [210.225717] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A] <7> [210.397042] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [210.397816] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [210.399592] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [210.399687] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [210.399773] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000 <7> [210.399859] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [210.400031] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz <7> [210.400038] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [210.400042] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41 <7> [210.400046] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0 <7> [210.400068] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes <7> [210.400173] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [210.400985] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [210.401074] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [210.401713] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:eDP-1] Same epoch counter 1 <7> [210.401731] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [210.402039] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] Same epoch counter 6 <7> [210.402118] [drm:drm_mode_setcrtc] [CRTC:233:pipe D] <7> [210.402117] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [210.402237] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:254:DP-1] Same epoch counter 1 <7> [210.402365] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [210.402488] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1 <7> [210.402499] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [210.402622] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] Same epoch counter 1 <7> [210.402633] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [210.402745] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:DP-2] Same epoch counter 1 <7> [210.402755] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [210.402864] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] Same epoch counter 1 <7> [210.402881] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1] <7> [210.403693] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [210.403787] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [210.404407] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [210.404496] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [210.404579] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000 <7> [210.404661] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [210.404761] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz <7> [210.404766] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [210.404770] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41 <7> [210.404773] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0 <7> [210.404785] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes <7> [210.404868] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [210.405677] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [210.405764] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [210.406390] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:eDP-1] Same epoch counter 1 <7> [210.406403] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [210.406539] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] Same epoch counter 6 <7> [210.406551] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [210.406667] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:254:DP-1] Same epoch counter 1 <7> [210.406678] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [210.406794] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1 <7> [210.406805] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [210.406920] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] Same epoch counter 1 <7> [210.406931] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [210.407043] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:DP-2] Same epoch counter 1 <7> [210.407054] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [210.407167] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] Same epoch counter 1 <7> [213.450745] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD off <7> [213.451865] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [213.452644] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [213.453766] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [213.454587] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [213.455203] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [213.456374] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [213.456584] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [213.458766] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [213.461056] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [213.462169] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.462313] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [213.462439] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.462556] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [213.462671] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.462787] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [213.462902] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.463018] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [213.463131] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.463243] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [213.463400] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [213.463581] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [213.463740] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.463888] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [213.463991] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [213.464120] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [213.510885] [drm:drm_mode_setcrtc] [CRTC:80:pipe A] <7> [213.511058] [drm:drm_mode_setcrtc] [CONNECTOR:236:eDP-1] <7> [213.511459] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:236:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36) <7> [213.512496] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 2 max rate 540000 max bpp 24 pixel clock 164250KHz <7> [213.513174] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 2 clock 270000 bpp 24 <7> [213.513924] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 492750 available 540000 <7> [213.514855] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:236:eDP-1] SDP split enable: no <7> [213.515545] i915 0000:00:02.0: [drm:intel_psr_compute_config [i915]] PSR2 is defeatured for this platform <7> [213.515723] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0 <7> [213.515843] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:235:DDI A/PHY A] [CRTC:80:pipe A] <7> [213.515935] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.enable (expected 0, found 1) <7> [213.516034] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.active (expected 0, found 1) <7> [213.516129] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in cpu_transcoder (expected -1, found 0) <7> [213.516224] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in lane_count (expected 0, found 2) <7> [213.516326] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 7654604/8388608 link 318941/524288) <7> [213.516427] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in output_types (expected 0x00000000, found 0x00000100) <7> [213.516576] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in framestart_delay (expected 0, found 1) <7> [213.516675] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hdisplay (expected 0, found 1920) <7> [213.516766] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_htotal (expected 0, found 2080) <7> [213.516855] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_start (expected 0, found 1920) <7> [213.516945] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_end (expected 0, found 2080) <7> [213.517037] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_start (expected 0, found 1968) <7> [213.517130] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_end (expected 0, found 2000) <7> [213.517222] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vdisplay (expected 0, found 1280) <7> [213.517321] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vtotal (expected 0, found 1317) <7> [213.517413] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_start (expected 0, found 1280) <7> [213.517545] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_end (expected 0, found 1317) <7> [213.517638] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_start (expected 0, found 1283) <7> [213.517730] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_end (expected 0, found 1293) <7> [213.517823] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hdisplay (expected 0, found 1920) <7> [213.517914] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_htotal (expected 0, found 2080) <7> [213.518005] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_start (expected 0, found 1920) <7> [213.518101] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_end (expected 0, found 2080) <7> [213.518197] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_start (expected 0, found 1968) <7> [213.518290] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2000) <7> [213.518397] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1280) <7> [213.518492] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vtotal (expected 0, found 1317) <7> [213.518630] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1280) <7> [213.518727] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1317) <7> [213.518825] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1283) <7> [213.518921] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1293) <7> [213.519015] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pixel_multiplier (expected 0, found 1) <7> [213.519109] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.flags (2) (expected 0, found 2) <7> [213.519203] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.flags (8) (expected 0, found 8) <7> [213.519297] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pipe_bpp (expected 0, found 24) <7> [213.519413] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_clock (expected 0, found 164250) <7> [213.519510] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_clock (expected 0, found 164250) <7> [213.519654] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in port_clock (expected 0, found 270000) <7> [213.519796] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0x3 (total dbuf slices 0x3), mbus joined? no->no <7> [213.519893] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x0 -> 0x3, ddb (0 - 0) -> (0 - 2048), active pipes 0x0 -> 0x1 <7> [213.520009] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 2006), size 0 -> 2006 <7> [213.520098] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb ( 0 - 0) -> (2006 - 2048), size 0 -> 42 <7> [213.520186] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm,swm,stwm <7> [213.520272] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 2, 3, 4, 6, 6, 8, 12, 0, 2, 0 <7> [213.520382] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 33, 49, 65, 97, 97, 129, 193, 30, 33, 47 <7> [213.520474] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 38, 55, 73, 108, 108, 143, 214, 31, 38, 48 <7> [213.520601] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 657000 num active planes 1 <7> [213.520706] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 12447 required 657 <7> [213.520807] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 14636 required 657 <7> [213.520905] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 15540 required 657 <7> [213.521003] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 16761 required 657 <7> [213.521103] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 657 <7> [213.521199] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 657 <7> [213.521294] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 657 <7> [213.521447] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (82125 kHz) > [CRTC:80:pipe A] min cdclk (0 kHz) <7> [213.521561] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (12833 kHz) > old min cdclk (0 kHz) <7> [213.521681] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz <7> [213.521779] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0 <7> [213.521875] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:80:pipe A] allocated DPLL 0 <7> [213.521970] i915 0000:00:02.0: [drm:intel_reference_shared_dpll.isra.0 [i915]] [CRTC:80:pipe A] reserving DPLL 0 <7> [213.522068] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [modeset] <7> [213.522164] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB <7> [213.522259] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0 <7> [213.522378] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [213.522513] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [213.522613] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [213.522709] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [213.522805] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 2; data_m: 7654604, data_n: 8388608, link_m: 318941, link_n: 524288, tu: 64 <7> [213.522900] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 2; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [213.522994] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [213.523090] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [213.523183] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0 <7> [213.523185] i915 0000:00:02.0: pixelformat: RGB <7> [213.523186] i915 0000:00:02.0: colorimetry: sRGB <7> [213.523188] i915 0000:00:02.0: bpc: 0 <7> [213.523189] i915 0000:00:02.0: dynamic range: VESA range <7> [213.523191] i915 0000:00:02.0: content type: Not defined <7> [213.523193] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2 <7> [213.523286] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa <7> [213.523402] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa <7> [213.523498] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: 164250 1920 1968 2000 2080 1280 1283 1293 1317, type: 0x48 flags: 0xa <7> [213.523631] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x40 0xa <7> [213.523726] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: 164250 1920 1968 2000 2080 1280 1283 1293 1317, type: 0x40 flags: 0xa <7> [213.523818] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 270000, pipe src: 1920x1280+0+0, pixel rate 164250 <7> [213.523908] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 102, ips linetime: 0 <7> [213.524001] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [213.524095] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [213.524188] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [213.524282] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x88, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [213.524409] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [213.524506] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [213.524636] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:284] 1920x1280 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [213.524733] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [213.524827] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 1920.000000x1280.000000+0.000000+0.000000 dst: 1920x1280+0+0 <7> [213.524921] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [213.525017] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [213.525109] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [213.525201] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [213.525293] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no <7> [213.537524] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [213.537592] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [213.537703] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [213.537832] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [213.538272] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [213.538443] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [213.538575] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [213.538966] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [213.539748] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [213.539850] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [213.552728] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [213.555013] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [213.555679] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [213.555786] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [213.556427] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [213.557625] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.557761] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [213.557875] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.557986] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [213.558097] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.558207] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [213.558328] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.558457] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [213.558591] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [213.558702] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [213.558815] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI A/PHY A] <7> [213.558910] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:244:DDI TC1/PHY B] <7> [213.559001] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:253:DDI TC2/PHY C] <7> [213.559089] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:255:DP-MST A] <7> [213.559177] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:256:DP-MST B] <7> [213.559262] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:257:DP-MST C] <7> [213.559363] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:258:DP-MST D] <7> [213.559471] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:266:DDI TC3/PHY D] <7> [213.559586] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:270:DDI TC4/PHY E] <7> [213.559676] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:272:DP-MST A] <7> [213.559764] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:273:DP-MST B] <7> [213.559851] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:274:DP-MST C] <7> [213.559936] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:275:DP-MST D] <7> [213.560025] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [213.560129] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [213.560227] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2 <7> [213.560338] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3 <7> [213.560436] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3 <7> [213.560611] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [213.560712] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:80:pipe A] <7> [213.560809] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0 <7> [213.560956] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turn panel power on <7> [213.561057] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [214.058838] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [214.059759] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [214.060694] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power on <7> [214.061891] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063 <7> [214.095351] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7> [214.095730] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long <7> [214.096420] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [214.097213] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A] <7> [214.271549] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [214.272246] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [214.273704] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD on <7> [214.274782] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7> [214.278200] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 0a c2 41 00 00 01 c0 02 00 00 00 00 0b 80 <7> [214.278280] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:236:eDP-1] Reloading eDP link rates <7> [214.279094] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [ENCODER:235:DDI A/PHY A] Using LINK_RATE_SET value 03 <7> [214.279925] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [ENCODER:235:DDI A/PHY A][DPRX] 8b/10b, lanes: 2, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7> [214.280139] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:235:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7> [214.281195] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:235:DDI A/PHY A][DPRX] Clock recovery OK <7> [214.281287] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:235:DDI A/PHY A][DPRX] Using DP training pattern TPS3 <7> [214.282850] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:235:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7> [214.282938] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Link Training passed at link rate = 270000, lane count = 2 <7> [214.283463] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A <7> [214.283610] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]] <7> [214.283698] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A <7> [214.283785] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] Performing OUI wait <7> [214.308183] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] set backlight PWM = 96000 <7> [214.317162] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3 <7> [214.317883] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1 <7> [214.319651] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:eDP-1] <7> [214.320214] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A] <7> [214.321246] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:235:DDI A/PHY A] Fec status: 0 <7> [214.321853] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [214.322862] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1] <7> [214.324505] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [214.325070] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [214.326469] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [214.326932] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [214.327231] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000 <7> [214.327575] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [214.327990] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz <7> [214.328011] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [214.328026] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41 <7> [214.328039] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0 <7> [214.328089] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes <7> [214.328447] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [214.329618] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [214.329992] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [214.331081] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:eDP-1] Same epoch counter 1 <7> [214.331140] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [214.331602] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] Same epoch counter 6 <7> [214.331635] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [214.331984] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:254:DP-1] Same epoch counter 1 <7> [214.332032] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [214.332485] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1 <7> [214.332512] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [214.332753] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] Same epoch counter 1 <7> [214.332779] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [214.333014] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:DP-2] Same epoch counter 1 <7> [214.333037] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [214.333259] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] Same epoch counter 1 <7> [214.338791] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [214.338976] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [214.339166] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010 <7> [214.351285] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [214.351448] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [214.392761] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:284] from all active usage due to RMFB ioctl <7> [214.392900] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:plane 1A] because [FB:284] is removed <7> [214.393023] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2006) -> ( 0 - 0), size 2006 -> 0 <7> [214.393586] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [214.394047] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 2, 3, 4, 6, 6, 8, 12, 0, 2, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [214.394524] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 16, 33, 49, 65, 97, 97, 129, 193, 30, 33, 47 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [214.394907] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 19, 38, 55, 73, 108, 108, 143, 214, 31, 38, 48 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [214.395277] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 0 num active planes 0 <7> [214.395766] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 12447 required 0 <7> [214.396188] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 14636 required 0 <7> [214.396643] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 15540 required 0 <7> [214.397059] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 16761 required 0 <7> [214.397509] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0 <7> [214.397918] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 0 <7> [214.398368] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 0 <7> [214.398937] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1 <7> [214.417785] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 2006), size 0 -> 2006 <7> [214.417895] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm,swm,stwm <7> [214.417990] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 2, 3, 4, 6, 6, 8, 12, 0, 2, 0 <7> [214.418082] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 33, 49, 65, 97, 97, 129, 193, 30, 33, 47 <7> [214.418171] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 38, 55, 73, 108, 108, 143, 214, 31, 38, 48 <7> [214.418259] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 657000 num active planes 1 <7> [214.418384] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 12447 required 657 <7> [214.418503] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 14636 required 657 <7> [214.418603] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 15540 required 657 <7> [214.418716] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 16761 required 657 <7> [214.418877] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 657 <7> [214.419035] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 657 <7> [214.419170] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 657 <7> [214.434033] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1 <6> [214.436175] [IGT] i915_pm_rpm: exiting, ret=0 <6> [214.450907] Console: switching to colour frame buffer device 240x80

<7> [208.247959] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]

<7> [208.247974] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]

<7> [208.248761] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [208.248864] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [208.249429] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [208.249524] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [208.249613] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000

<7> [208.249696] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [208.249793] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz

<7> [208.249799] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [208.249802] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41

<7> [208.249805] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0

<7> [208.249818] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes

<7> [208.249900] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [208.250648] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [208.250739] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [208.251378] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :

<7> [208.251389] [drm:drm_mode_debug_printmodeline] Modeline "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa

<7> [208.251457] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1]

<7> [208.251467] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [208.251577] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] disconnected

<7> [208.251641] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1]

<7> [208.251650] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [208.251755] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1] disconnected

<7> [208.251819] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]

<7> [208.251828] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [208.251929] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [208.251992] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3]

<7> [208.252001] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [208.252104] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] disconnected

<7> [208.252167] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2]

<7> [208.252176] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [208.252277] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2] disconnected

<7> [208.252370] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4]

<7> [208.252380] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [208.252492] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] disconnected

<7> [208.258772] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1]

<7> [208.258786] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [208.258910] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] disconnected

<7> [208.259345] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1]

<7> [208.259355] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [208.259477] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1] disconnected

<7> [208.259918] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]

<7> [208.259927] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [208.260036] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [208.260524] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3]

<7> [208.260533] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [208.260643] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] disconnected

<7> [208.261073] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2]

<7> [208.261082] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [208.261189] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2] disconnected

<7> [208.261641] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4]

<7> [208.261650] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [208.261752] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] disconnected

<7> [208.262315] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]

<7> [208.262325] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]

<7> [208.263089] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [208.263181] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [208.263770] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [208.263859] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [208.263947] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000

<7> [208.264036] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [208.264138] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz

<7> [208.264143] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [208.264146] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41

<7> [208.264149] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0

<7> [208.264161] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes

<7> [208.264247] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [208.265014] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [208.265105] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [208.265728] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :

<7> [208.265739] [drm:drm_mode_debug_printmodeline] Modeline "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa

<7> [208.265757] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1]

<7> [208.265768] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [208.265881] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] disconnected

<7> [208.265905] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1]

<7> [208.265914] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [208.266022] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:254:DP-1] disconnected

<7> [208.266044] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]

<7> [208.266053] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [208.266159] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [208.266179] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3]

<7> [208.266188] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [208.266293] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] disconnected

<7> [208.266340] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2]

<7> [208.266349] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [208.266454] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:DP-2] disconnected

<7> [208.266474] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4]

<7> [208.266483] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [208.266589] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] disconnected

<7> [209.292580] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.enable (expected 1, found 0)

<7> [209.293490] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.active (expected 1, found 0)

<7> [209.294213] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in cpu_transcoder (expected 0, found -1)

<7> [209.294950] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in lane_count (expected 2, found 0)

<7> [209.295348] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dp_m_n (expected tu 64 data 7654604/8388608 link 318941/524288, found tu 0, data 0/0 link 0/0)

<7> [209.295457] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in output_types (expected 0x00000100, found 0x00000000)

<7> [209.295555] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in framestart_delay (expected 1, found 0)

<7> [209.295654] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hdisplay (expected 1920, found 0)

<7> [209.295761] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_htotal (expected 2080, found 0)

<7> [209.295859] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_start (expected 1920, found 0)

<7> [209.295955] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_end (expected 2080, found 0)

<7> [209.296051] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_start (expected 1968, found 0)

<7> [209.296150] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_end (expected 2000, found 0)

<7> [209.296248] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vdisplay (expected 1280, found 0)

<7> [209.296358] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vtotal (expected 1317, found 0)

<7> [209.296461] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_start (expected 1280, found 0)

<7> [209.296561] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_end (expected 1317, found 0)

<7> [209.296661] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_start (expected 1283, found 0)

<7> [209.296762] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_end (expected 1293, found 0)

<7> [209.296859] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hdisplay (expected 1920, found 0)

<7> [209.296955] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_htotal (expected 2080, found 0)

<7> [209.297051] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_start (expected 1920, found 0)

<7> [209.297148] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_end (expected 2080, found 0)

<7> [209.297245] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_start (expected 1968, found 0)

<7> [209.297358] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_end (expected 2000, found 0)

<7> [209.297459] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vdisplay (expected 1280, found 0)

<7> [209.297560] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vtotal (expected 1317, found 0)

<7> [209.297657] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_start (expected 1280, found 0)

<7> [209.297753] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_end (expected 1317, found 0)

<7> [209.297850] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_start (expected 1283, found 0)

<7> [209.297946] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_end (expected 1293, found 0)

<7> [209.298040] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pixel_multiplier (expected 1, found 0)

<7> [209.298131] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.flags (2) (expected 2, found 0)

<7> [209.298222] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.flags (8) (expected 8, found 0)

<7> [209.298325] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pipe_bpp (expected 24, found 0)

<7> [209.298427] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_clock (expected 164250, found 0)

<7> [209.298525] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_clock (expected 164250, found 0)

<7> [209.298616] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in port_clock (expected 270000, found 0)

<7> [209.298712] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll.isra.0 [i915]] [CRTC:80:pipe A] releasing DPLL 0

<7> [209.298843] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0x3), mbus joined? no->no

<7> [209.298947] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0x0, ddb (0 - 2048) -> (0 - 0), active pipes 0x1 -> 0x0

<7> [209.299064] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2006) -> ( 0 - 0), size 2006 -> 0

<7> [209.299157] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb (2006 - 2048) -> ( 0 - 0), size 42 -> 0

<7> [209.299247] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [209.299346] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 2, 3, 4, 6, 6, 8, 12, 0, 2, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [209.299440] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 16, 33, 49, 65, 97, 97, 129, 193, 30, 33, 47 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [209.299532] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 19, 38, 55, 73, 108, 108, 143, 214, 31, 38, 48 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [209.299621] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 0 num active planes 0

<7> [209.299726] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 12447 required 0

<7> [209.299828] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 14636 required 0

<7> [209.299933] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 15540 required 0

<7> [209.300036] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 16761 required 0

<7> [209.300136] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0

<7> [209.300235] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 0

<7> [209.300344] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 0

<7> [209.300466] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz

<7> [209.300566] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0

<7> [209.300668] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: no [modeset]

<7> [209.300769] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no

<7> [209.300869] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [209.300969] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [209.301068] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [209.301171] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [209.301273] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no

<7> [209.301474] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1

<7> [209.308699] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]

<7> [209.514520] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] set backlight PWM = 0

<7> [209.515913] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A

<7> [209.527024] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000

<7> [209.526940] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turn panel power off

<7> [209.527448] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - short

<7> [209.527736] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power off time

<7> [209.528460] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060

<7> [209.582387] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [209.583051] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A

<7> [209.583837] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [209.583833] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:235:DDI A/PHY A]

<7> [209.584545] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:80:pipe A]

<7> [209.585216] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0

<7> [209.585915] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI A/PHY A]

<7> [209.586519] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:244:DDI TC1/PHY B]

<7> [209.587041] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:253:DDI TC2/PHY C]

<7> [209.587592] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:255:DP-MST A]

<7> [209.588081] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:256:DP-MST B]

<7> [209.588612] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:257:DP-MST C]

<7> [209.589086] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:258:DP-MST D]

<7> [209.589601] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:266:DDI TC3/PHY D]

<7> [209.590073] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:270:DDI TC4/PHY E]

<7> [209.590583] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:272:DP-MST A]

<7> [209.591050] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:273:DP-MST B]

<7> [209.591569] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:274:DP-MST C]

<7> [209.592027] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:275:DP-MST D]

<7> [209.592483] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:eDP-1]

<7> [209.592934] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [209.593437] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [209.593907] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2

<7> [209.594394] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3

<7> [209.594891] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3

<7> [209.595461] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [209.596034] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]

<7> [209.596807] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [209.597293] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [209.597811] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [209.638655] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010

<7> [209.638862] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long

<7> [209.639234] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [209.639638] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A]

<7> [209.802559] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [209.804859] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device

<7> [209.811712] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled

<7> [209.815174] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [209.816375] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.816530] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [209.816654] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.816774] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [209.816885] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.816990] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [209.817097] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.817209] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.

<7> [209.817322] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.817448] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.

<7> [209.817640] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0

<7> [209.817929] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1

<7> [209.818148] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.818322] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9

<7> [209.818434] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08

<7> [209.818619] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended

<6> [209.906460] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state

<7> [209.927691] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device

<7> [209.927934] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9

<7> [209.928372] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00

<7> [209.928853] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [209.929876] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [209.931026] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0

<7> [209.931391] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [209.931872] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [209.933856] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [209.934115] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [209.949313] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<7> [209.951596] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed

<7> [209.951912] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device

<7> [209.953957] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled

<7> [209.956269] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [209.957402] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.957539] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [209.957659] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.957776] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [209.957892] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.958008] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [209.958122] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.958239] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.

<7> [209.958361] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.958478] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.

<7> [209.958608] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0

<7> [209.958781] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1

<7> [209.958941] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [209.959092] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9

<7> [209.959198] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08

<7> [209.959344] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended

<7> [209.983498] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device

<7> [209.983684] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9

<7> [209.983984] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00

<7> [209.984336] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [209.985067] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [209.985447] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0

<7> [209.985716] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [209.986059] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [209.987677] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [209.987889] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [210.000910] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<7> [210.003138] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed

<7> [210.003261] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device

<7> [210.004354] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]

<7> [210.005451] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled

<7> [210.007810] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [210.008942] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.009065] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [210.009182] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.009296] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [210.009427] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.009539] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [210.009650] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.009762] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.

<7> [210.009874] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.009984] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.

<7> [210.010113] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0

<7> [210.010424] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1

<7> [210.010590] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.010759] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9

<7> [210.010884] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08

<7> [210.011037] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended

<7> [210.035103] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device

<7> [210.035416] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9

<7> [210.035697] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00

<7> [210.036030] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [210.036863] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [210.037693] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0

<7> [210.037934] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [210.038252] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [210.039850] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [210.040044] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [210.055174] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<7> [210.056401] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed

<7> [210.056538] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [210.056669] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [210.057461] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [210.058647] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.058773] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [210.058892] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.059011] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [210.059128] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.059245] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [210.059372] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.059498] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.

<7> [210.059618] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [210.059735] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.

<7> [210.059840] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [210.060092] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD on

<7> [210.060235] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [210.186944] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [210.187861] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [210.188909] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068

<7> [210.189680] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 panel power wasn't enabled

<7> [210.223557] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010

<7> [210.223984] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long

<7> [210.224805] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [210.225717] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A]

<7> [210.397042] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [210.397816] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [210.399592] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [210.399687] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [210.399773] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000

<7> [210.399859] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [210.400031] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz

<7> [210.400038] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [210.400042] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41

<7> [210.400046] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0

<7> [210.400068] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes

<7> [210.400173] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [210.400985] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [210.401074] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [210.401713] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:eDP-1] Same epoch counter 1

<7> [210.401731] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [210.402039] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] Same epoch counter 6

<7> [210.402117] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [210.402237] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:254:DP-1] Same epoch counter 1

<7> [210.402365] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [210.402488] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1

<7> [210.402499] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [210.402622] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] Same epoch counter 1

<7> [210.402633] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [210.402745] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:DP-2] Same epoch counter 1

<7> [210.402755] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [210.402864] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] Same epoch counter 1

<7> [210.402881] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]

<7> [210.403693] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [210.403787] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [210.404407] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [210.404496] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [210.404579] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000

<7> [210.404661] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [210.404761] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz

<7> [210.404766] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [210.404770] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41

<7> [210.404773] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0

<7> [210.404785] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes

<7> [210.404868] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [210.405677] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [210.405764] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [210.406390] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:eDP-1] Same epoch counter 1

<7> [210.406403] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [210.406539] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] Same epoch counter 6

<7> [210.406551] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [210.406667] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:254:DP-1] Same epoch counter 1

<7> [210.406678] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [210.406794] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1

<7> [210.406805] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [210.406920] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] Same epoch counter 1

<7> [210.406931] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [210.407043] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:DP-2] Same epoch counter 1

<7> [210.407054] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [210.407167] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] Same epoch counter 1

<7> [213.450745] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD off

<7> [213.451865] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [213.452644] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [213.453766] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [213.454587] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [213.455203] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [213.456374] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [213.456584] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device

<7> [213.458766] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled

<7> [213.461056] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [213.462169] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.462313] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [213.462439] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.462556] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [213.462671] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.462787] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [213.462902] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.463018] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.

<7> [213.463131] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.463243] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.

<7> [213.463400] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0

<7> [213.463581] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1

<7> [213.463740] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.463888] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9

<7> [213.463991] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08

<7> [213.464120] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended

<7> [213.511459] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:236:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)

<7> [213.512496] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 2 max rate 540000 max bpp 24 pixel clock 164250KHz

<7> [213.513174] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 2 clock 270000 bpp 24

<7> [213.513924] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 492750 available 540000

<7> [213.514855] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:236:eDP-1] SDP split enable: no

<7> [213.515545] i915 0000:00:02.0: [drm:intel_psr_compute_config [i915]] PSR2 is defeatured for this platform

<7> [213.515723] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0

<7> [213.515843] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:235:DDI A/PHY A] [CRTC:80:pipe A]

<7> [213.515935] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.enable (expected 0, found 1)

<7> [213.516034] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.active (expected 0, found 1)

<7> [213.516129] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in cpu_transcoder (expected -1, found 0)

<7> [213.516224] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in lane_count (expected 0, found 2)

<7> [213.516326] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 7654604/8388608 link 318941/524288)

<7> [213.516427] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in output_types (expected 0x00000000, found 0x00000100)

<7> [213.516576] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in framestart_delay (expected 0, found 1)

<7> [213.516675] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hdisplay (expected 0, found 1920)

<7> [213.516766] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_htotal (expected 0, found 2080)

<7> [213.516855] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_start (expected 0, found 1920)

<7> [213.516945] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hblank_end (expected 0, found 2080)

<7> [213.517037] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_start (expected 0, found 1968)

<7> [213.517130] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_hsync_end (expected 0, found 2000)

<7> [213.517222] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vdisplay (expected 0, found 1280)

<7> [213.517321] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vtotal (expected 0, found 1317)

<7> [213.517413] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_start (expected 0, found 1280)

<7> [213.517545] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vblank_end (expected 0, found 1317)

<7> [213.517638] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_start (expected 0, found 1283)

<7> [213.517730] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_vsync_end (expected 0, found 1293)

<7> [213.517823] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hdisplay (expected 0, found 1920)

<7> [213.517914] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_htotal (expected 0, found 2080)

<7> [213.518005] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_start (expected 0, found 1920)

<7> [213.518101] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hblank_end (expected 0, found 2080)

<7> [213.518197] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_start (expected 0, found 1968)

<7> [213.518290] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2000)

<7> [213.518397] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1280)

<7> [213.518492] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vtotal (expected 0, found 1317)

<7> [213.518630] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1280)

<7> [213.518727] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1317)

<7> [213.518825] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1283)

<7> [213.518921] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1293)

<7> [213.519015] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pixel_multiplier (expected 0, found 1)

<7> [213.519109] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.flags (2) (expected 0, found 2)

<7> [213.519203] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.flags (8) (expected 0, found 8)

<7> [213.519297] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pipe_bpp (expected 0, found 24)

<7> [213.519413] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.pipe_mode.crtc_clock (expected 0, found 164250)

<7> [213.519510] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in hw.adjusted_mode.crtc_clock (expected 0, found 164250)

<7> [213.519654] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in port_clock (expected 0, found 270000)

<7> [213.519796] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0x3 (total dbuf slices 0x3), mbus joined? no->no

<7> [213.519893] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x0 -> 0x3, ddb (0 - 0) -> (0 - 2048), active pipes 0x0 -> 0x1

<7> [213.520009] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 2006), size 0 -> 2006

<7> [213.520098] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb ( 0 - 0) -> (2006 - 2048), size 0 -> 42

<7> [213.520186] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm,*swm,*stwm

<7> [213.520272] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 2, 3, 4, 6, 6, 8, 12, 0, 2, 0

<7> [213.520382] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 33, 49, 65, 97, 97, 129, 193, 30, 33, 47

<7> [213.520474] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 38, 55, 73, 108, 108, 143, 214, 31, 38, 48

<7> [213.520601] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 657000 num active planes 1

<7> [213.520706] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 12447 required 657

<7> [213.520807] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 14636 required 657

<7> [213.520905] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 15540 required 657

<7> [213.521003] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 16761 required 657

<7> [213.521103] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 657

<7> [213.521199] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 657

<7> [213.521294] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 657

<7> [213.521447] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (82125 kHz) > [CRTC:80:pipe A] min cdclk (0 kHz)

<7> [213.521561] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (12833 kHz) > old min cdclk (0 kHz)

<7> [213.521681] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz

<7> [213.521779] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0

<7> [213.521875] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:80:pipe A] allocated DPLL 0

<7> [213.521970] i915 0000:00:02.0: [drm:intel_reference_shared_dpll.isra.0 [i915]] [CRTC:80:pipe A] reserving DPLL 0

<7> [213.522068] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [modeset]

<7> [213.522164] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB

<7> [213.522259] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0

<7> [213.522378] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [213.522513] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [213.522613] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [213.522709] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [213.522805] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 2; data_m: 7654604, data_n: 8388608, link_m: 318941, link_n: 524288, tu: 64

<7> [213.522900] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 2; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [213.522994] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [213.523090] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [213.523183] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0

<7> [213.523193] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2

<7> [213.523286] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa

<7> [213.523402] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa

<7> [213.523498] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: 164250 1920 1968 2000 2080 1280 1283 1293 1317, type: 0x48 flags: 0xa

<7> [213.523631] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x40 0xa

<7> [213.523726] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: 164250 1920 1968 2000 2080 1280 1283 1293 1317, type: 0x40 flags: 0xa

<7> [213.523818] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 270000, pipe src: 1920x1280+0+0, pixel rate 164250

<7> [213.523908] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 102, ips linetime: 0

<7> [213.524001] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [213.524095] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [213.524188] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [213.524282] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x88, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [213.524409] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [213.524506] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [213.524636] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:284] 1920x1280 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes

<7> [213.524733] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0

<7> [213.524827] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 1920.000000x1280.000000+0.000000+0.000000 dst: 1920x1280+0+0

<7> [213.524921] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [213.525017] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [213.525109] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [213.525201] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [213.525293] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no

<7> [213.537524] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device

<7> [213.537592] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9

<7> [213.537703] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00

<7> [213.537832] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [213.538272] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [213.538443] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0

<7> [213.538575] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [213.538966] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [213.539748] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [213.539850] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [213.552728] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<7> [213.555013] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed

<7> [213.555679] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [213.555786] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [213.556427] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [213.557625] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.557761] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [213.557875] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.557986] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [213.558097] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.558207] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [213.558328] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.558457] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.

<7> [213.558591] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [213.558702] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.

<7> [213.558815] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI A/PHY A]

<7> [213.558910] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:244:DDI TC1/PHY B]

<7> [213.559001] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:253:DDI TC2/PHY C]

<7> [213.559089] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:255:DP-MST A]

<7> [213.559177] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:256:DP-MST B]

<7> [213.559262] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:257:DP-MST C]

<7> [213.559363] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:258:DP-MST D]

<7> [213.559471] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:266:DDI TC3/PHY D]

<7> [213.559586] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:270:DDI TC4/PHY E]

<7> [213.559676] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:272:DP-MST A]

<7> [213.559764] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:273:DP-MST B]

<7> [213.559851] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:274:DP-MST C]

<7> [213.559936] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:275:DP-MST D]

<7> [213.560025] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [213.560129] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [213.560227] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2

<7> [213.560338] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3

<7> [213.560436] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3

<7> [213.560611] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [213.560712] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:80:pipe A]

<7> [213.560809] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0

<7> [213.560956] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turn panel power on

<7> [213.561057] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [214.058838] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [214.059759] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [214.060694] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power on

<7> [214.061891] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063

<7> [214.095351] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010

<7> [214.095730] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long

<7> [214.096420] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [214.097213] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A]

<7> [214.271549] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [214.272246] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [214.273704] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD on

<7> [214.274782] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b

<7> [214.278200] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 0a c2 41 00 00 01 c0 02 00 00 00 00 0b 80

<7> [214.278280] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:236:eDP-1] Reloading eDP link rates

<7> [214.279094] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [ENCODER:235:DDI A/PHY A] Using LINK_RATE_SET value 03

<7> [214.279925] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [ENCODER:235:DDI A/PHY A][DPRX] 8b/10b, lanes: 2, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0

<7> [214.280139] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:235:DDI A/PHY A][DPRX] Using DP training pattern TPS1

<7> [214.281195] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:235:DDI A/PHY A][DPRX] Clock recovery OK

<7> [214.281287] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:235:DDI A/PHY A][DPRX] Using DP training pattern TPS3

<7> [214.282850] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:235:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful

<7> [214.282938] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Link Training passed at link rate = 270000, lane count = 2

<7> [214.283463] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A

<7> [214.283610] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]

<7> [214.283698] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A

<7> [214.283785] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] Performing OUI wait

<7> [214.308183] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] set backlight PWM = 96000

<7> [214.317162] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3

<7> [214.317883] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1

<7> [214.319651] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:eDP-1]

<7> [214.320214] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]

<7> [214.321246] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:235:DDI A/PHY A] Fec status: 0

<7> [214.321853] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [214.322862] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]

<7> [214.324505] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [214.325070] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [214.326469] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [214.326932] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [214.327231] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000

<7> [214.327575] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [214.327990] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz

<7> [214.328011] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [214.328026] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41

<7> [214.328039] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0

<7> [214.328089] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes

<7> [214.328447] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [214.329618] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [214.329992] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [214.331081] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:eDP-1] Same epoch counter 1

<7> [214.331140] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [214.331602] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:245:HDMI-A-1] Same epoch counter 6

<7> [214.331635] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [214.331984] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:254:DP-1] Same epoch counter 1

<7> [214.332032] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [214.332485] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1

<7> [214.332512] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [214.332753] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:267:HDMI-A-3] Same epoch counter 1

<7> [214.332779] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [214.333014] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:DP-2] Same epoch counter 1

<7> [214.333037] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [214.333259] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:279:HDMI-A-4] Same epoch counter 1

<7> [214.338791] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [214.338976] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<7> [214.339166] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010

<7> [214.351285] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3

<7> [214.351448] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [214.392761] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:284] from all active usage due to RMFB ioctl

<7> [214.392900] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:plane 1A] because [FB:284] is removed

<7> [214.393023] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2006) -> ( 0 - 0), size 2006 -> 0

<7> [214.393586] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [214.394047] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 2, 3, 4, 6, 6, 8, 12, 0, 2, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [214.394524] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 16, 33, 49, 65, 97, 97, 129, 193, 30, 33, 47 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [214.394907] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 19, 38, 55, 73, 108, 108, 143, 214, 31, 38, 48 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [214.395277] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 0 num active planes 0

<7> [214.395766] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 12447 required 0

<7> [214.396188] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 14636 required 0

<7> [214.396643] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 15540 required 0

<7> [214.397059] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 16761 required 0

<7> [214.397509] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0

<7> [214.397918] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 0

<7> [214.398368] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 0

<7> [214.398937] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1

<7> [214.417785] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 2006), size 0 -> 2006

<7> [214.417895] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm,*swm,*stwm

<7> [214.417990] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 2, 3, 4, 6, 6, 8, 12, 0, 2, 0

<7> [214.418082] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 33, 49, 65, 97, 97, 129, 193, 30, 33, 47

<7> [214.418171] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 38, 55, 73, 108, 108, 143, 214, 31, 38, 48

<7> [214.418259] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 657000 num active planes 1

<7> [214.418384] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 12447 required 657

<7> [214.418503] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 14636 required 657

<7> [214.418603] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 15540 required 657

<7> [214.418716] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 16761 required 657

<7> [214.418877] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 657

<7> [214.419035] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 657

<7> [214.419170] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 657

<7> [214.434033] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1

<6> [214.450907] Console: switching to colour frame buffer device 240x80

Results for igt@i915_pm_rpm@basic-pci-d3-state