Results for igt@i915_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Hostname 
shard-rkl-2
Igt-Version 
IGT-Version: 1.27.1-gb6b1ceb4f (x86_64) (Linux: 6.3.0-rc1-linus-v6.3-rc1-gfe15c26ee26e+ x86_64)
Out 
Starting subtest: basic-rte
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 0
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x76/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x159/0x2b0 [i915]
   intel_atomic_commit_tail+0xb26/0xe40 [i915]
   intel_atomic_commit+0x380/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
Wakeref count: 0
Subtest basic-rte: SUCCESS (1.447s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 0
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x76/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x159/0x2b0 [i915]
   intel_atomic_commit_tail+0xb26/0xe40 [i915]
   intel_atomic_commit+0x380/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
Wakeref count: 0
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.447s)
Dmesg
<6> [39.698361] [IGT] i915_pm_rpm: executing
<6> [39.700510] [IGT] i915_pm_rpm: starting subtest basic-rte
<7> [39.700575] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [39.701024] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1]
<7> [39.701040] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [39.701145] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.701919] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.702064] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] disconnected
<7> [39.702136] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2]
<7> [39.702146] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [39.702257] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.703139] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.703265] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] disconnected
<7> [39.703327] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:148:DP-1]
<7> [39.703337] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [39.703436] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.704335] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.704481] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:148:DP-1] disconnected
<7> [39.704541] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3]
<7> [39.704565] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [39.704675] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.705573] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.705711] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] disconnected
<7> [39.710609] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1]
<7> [39.710623] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [39.710734] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.711449] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.711571] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] disconnected
<7> [39.712094] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2]
<7> [39.712105] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [39.712200] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.712962] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.713084] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] disconnected
<7> [39.713611] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:148:DP-1]
<7> [39.713624] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [39.713737] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.714452] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.714583] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:148:DP-1] disconnected
<7> [39.715079] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3]
<7> [39.715095] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [39.715207] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.715955] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.716075] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] disconnected
<7> [39.716526] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1]
<7> [39.716541] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [39.716697] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.717428] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.717552] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] disconnected
<7> [39.717576] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2]
<7> [39.717586] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [39.717709] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.718656] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.718812] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] disconnected
<7> [39.718841] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:148:DP-1]
<7> [39.718851] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [39.718952] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.719900] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.720020] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:148:DP-1] disconnected
<7> [39.720043] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3]
<7> [39.720053] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [39.720161] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [39.721098] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [39.721253] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] disconnected
<7> [40.725171] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [40.736271] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [40.737731] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.738399] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [40.739349] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [40.740664] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [40.741239] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.741764] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [40.742097] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [40.743135] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [40.768707] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [40.769030] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [40.769528] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [40.770118] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [40.771132] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [40.771979] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [40.772632] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [40.773739] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [40.776284] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [40.776843] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [40.787195] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [40.788341] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [40.788427] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [40.789621] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [40.789709] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [40.789874] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] Same epoch counter 1
<7> [40.790506] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [40.791102] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [40.791106] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [40.792456] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [40.793658] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.793787] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [40.793911] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.794031] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [40.794151] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.794278] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [40.794398] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.794517] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [40.794676] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [40.795017] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [40.795197] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.795359] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [40.795464] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [40.795663] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [40.820276] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [40.820372] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [40.820487] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [40.820667] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [40.821211] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [40.821625] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [40.821752] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [40.822130] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [40.823069] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [40.823207] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [40.831851] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [40.831916] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [40.833048] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [40.833179] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] Same epoch counter 1
<7> [40.833206] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [40.833341] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [40.834256] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [40.834388] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:148:DP-1] Same epoch counter 1
<7> [40.834634] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [40.837905] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [40.839136] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.839326] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [40.839485] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.839640] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [40.839770] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.839893] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [40.840011] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.840129] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [40.840265] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [40.840422] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [40.840562] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [40.840769] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.840931] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [40.841036] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [40.841178] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [40.865305] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [40.865398] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [40.865523] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [40.865717] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [40.866246] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [40.866451] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [40.866570] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [40.866858] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [40.867567] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [40.867669] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [40.873831] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [40.873895] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [40.875035] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [40.875148] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] Same epoch counter 1
<7> [40.875172] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [40.875271] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [40.876236] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [40.876364] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] Same epoch counter 1
<7> [40.876376] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [40.876492] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [40.877451] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [40.877568] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] Same epoch counter 1
<7> [40.877580] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [40.877691] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [40.878672] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [40.878801] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:148:DP-1] Same epoch counter 1
<7> [40.878813] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [40.878915] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [40.879896] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [40.880015] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] Same epoch counter 1
<7> [40.880029] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [40.882381] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [40.883562] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.883693] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [40.883821] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.883941] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [40.884059] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.884182] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [40.884300] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.884419] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [40.884562] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [40.884821] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [40.885000] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.885163] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [40.885267] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [40.885409] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [40.939904] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [40.952319] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [40.952905] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [40.953407] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [40.954017] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [40.955076] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [40.956460] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [40.957023] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [40.958506] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [40.960891] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [40.961360] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [40.973991] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [40.974206] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [40.975257] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [40.977715] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [40.978903] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.979050] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [40.979182] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.979305] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [40.979427] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.979560] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [40.979690] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.979825] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [40.979961] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [40.980177] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [40.980360] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [40.980527] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [40.980671] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [40.980832] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [41.005381] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [41.005488] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [41.005698] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [41.005998] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [41.006698] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [41.007227] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [41.007446] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [41.007946] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [41.009124] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [41.009330] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [41.015615] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [41.015753] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [41.018032] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [41.019226] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [41.020455] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.020620] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [41.020749] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.020869] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [41.020987] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.021113] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [41.021234] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.021353] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [41.021491] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [41.021756] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [41.021943] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.022106] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [41.022211] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [41.022353] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [41.046037] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [41.046139] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [41.046280] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [41.046485] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [41.047170] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [41.047446] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [41.047668] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [41.047996] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [41.049089] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [41.049263] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [41.056707] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [41.056775] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.057914] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.058026] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] Same epoch counter 1
<7> [41.058043] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [41.058153] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.059133] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.059253] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] Same epoch counter 1
<7> [41.059265] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [41.059364] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.060341] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.060456] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:148:DP-1] Same epoch counter 1
<7> [41.060474] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [41.060586] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.061570] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.061689] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] Same epoch counter 1
<7> [41.061714] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [41.061813] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.062785] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.062903] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] Same epoch counter 1
<7> [41.062922] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [41.063018] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.063998] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.064111] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] Same epoch counter 1
<7> [41.064124] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [41.064227] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.065216] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.065324] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:148:DP-1] Same epoch counter 1
<7> [41.065336] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [41.065439] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.066429] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.066539] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] Same epoch counter 1
<7> [41.066567] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [41.068911] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [41.070106] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.070233] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [41.070353] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.070473] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [41.070604] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.070732] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [41.070857] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.070975] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [41.071112] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [41.071317] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [41.071506] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.071693] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [41.071797] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [41.071938] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [41.130005] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [41.130518] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [41.131104] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [41.131689] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [41.132723] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [41.134057] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [41.134540] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [41.135677] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [41.136353] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [41.136454] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [41.143805] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [41.145017] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [41.145198] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.146263] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] Same epoch counter 1
<7> [41.146278] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [41.146518] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] Same epoch counter 1
<7> [41.146529] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [41.147469] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:148:DP-1] Same epoch counter 1
<7> [41.147528] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [41.147481] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [41.148697] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.148848] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] Same epoch counter 1
<7> [41.148865] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [41.151166] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [41.152358] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.152485] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [41.152642] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.152787] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [41.152910] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.153036] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [41.153158] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.153276] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [41.153418] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [41.153733] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [41.153931] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.154095] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [41.154198] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [41.154339] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [41.179041] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [41.179130] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [41.179243] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [41.179387] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [41.179898] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [41.180145] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [41.180251] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [41.180480] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [41.181363] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [41.181513] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [41.187703] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [41.187818] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [41.188674] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [41.191355] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [41.192607] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.192733] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [41.192853] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.192972] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [41.193090] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.193211] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [41.193328] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.193452] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [41.193619] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [41.193836] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [41.194016] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.194178] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [41.194281] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [41.194428] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [41.219044] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [41.219140] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [41.219274] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [41.219439] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [41.220050] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [41.220275] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [41.220381] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [41.220623] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [41.221398] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [41.221513] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [41.228961] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [41.229093] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [41.230265] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [41.232624] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [41.233807] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.233997] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [41.234129] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.234249] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [41.234367] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.234489] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [41.234644] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.234784] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [41.234976] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [41.235176] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [41.235355] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.235517] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [41.235641] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [41.235815] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [41.260385] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [41.260506] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [41.260735] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [41.261007] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [41.261636] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [41.261928] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [41.262094] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [41.262401] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [41.263466] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [41.263669] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [41.271108] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [41.271175] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.272329] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.272448] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] Same epoch counter 1
<7> [41.272465] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [41.272581] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.273520] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.273653] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] Same epoch counter 1
<7> [41.273669] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [41.273769] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.274754] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.274870] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:148:DP-1] Same epoch counter 1
<7> [41.274883] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [41.274979] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.275981] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.276092] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] Same epoch counter 1
<7> [41.276111] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [41.276211] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.277205] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.277314] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] Same epoch counter 1
<7> [41.277326] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [41.277420] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.278419] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.278527] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] Same epoch counter 1
<7> [41.278538] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [41.278679] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.279630] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.279740] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:148:DP-1] Same epoch counter 1
<7> [41.279751] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [41.279845] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.280859] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.280975] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] Same epoch counter 1
<7> [41.280989] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [41.283329] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [41.284520] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.284675] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [41.284805] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.284924] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [41.285044] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.285167] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [41.285285] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.285409] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [41.285552] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [41.285772] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [41.285949] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.286111] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [41.286215] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [41.286356] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [41.375335] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [41.375886] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [41.376395] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [41.377015] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [41.378164] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [41.379624] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [41.380113] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [41.381529] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [41.383897] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [41.384313] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [41.396880] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:134:HDMI-A-1]
<7> [41.398082] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [41.398277] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.399328] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [41.399462] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:134:HDMI-A-1] Same epoch counter 1
<7> [41.399477] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:144:HDMI-A-2]
<7> [41.399521] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [41.399674] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [41.400509] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [41.401836] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.402036] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [41.402216] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.402428] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [41.402583] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.402734] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [41.402862] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [41.402989] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [41.403090] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [41.403258] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [41.403368] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:144:HDMI-A-2] Same epoch counter 1
<7> [41.403407] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:148:DP-1]
<7> [41.403618] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:148:DP-1] Same epoch counter 1
<7> [41.403639] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:155:HDMI-A-3]
<7> [41.403780] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:155:HDMI-A-3] Same epoch counter 1
<7> [41.415392] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [41.415523] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [41.415660] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [41.415764] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [41.417015] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [41.454384] [IGT] i915_pm_rpm: exiting, ret=0
Created at 2023-03-06 23:33:27