Result: pass
git-log-oneline run0 boot0 dmesg0 runtimes0
| Detail | Value |
|---|---|
| Time | 2.41 seconds |
| Igt-Version | IGT-Version: 1.23-g78619fde (x86_64) (Linux: 4.19.0-g84df9525b0c2-linus-v4.19 x86_64) |
| Out | Starting subtest: basic-flip-B Subtest basic-flip-B: SUCCESS (2.408s) Test requirement not met in function igt_display_require_output_on_pipe, file ../lib/igt_kms.c:2086: Test requirement: !(pipe >= igt_display_get_n_pipes(display)) Pipe D does not exist. Test requirement not met in function igt_display_require_output_on_pipe, file ../lib/igt_kms.c:2086: Test requirement: !(pipe >= igt_display_get_n_pipes(display)) Pipe E does not exist. Test requirement not met in function igt_display_require_output_on_pipe, file ../lib/igt_kms.c:2086: Test requirement: !(pipe >= igt_display_get_n_pipes(display)) Pipe F does not exist. |
| Err | Starting subtest: basic-flip-B Subtest basic-flip-B: SUCCESS (2.408s) |
| Dmesg | <6> [166.024614] Console: switching to colour dummy device 80x25 <6> [166.024730] [IGT] kms_busy: executing <7> [166.085421] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:72:HDMI-A-1] <7> [166.085505] [drm:intel_hdmi_detect [i915]] [CONNECTOR:72:HDMI-A-1] <7> [166.085804] [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [166.085874] [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [166.086441] [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [166.086454] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [166.086536] [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [166.086619] [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [166.087633] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [166.087705] [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [166.087987] [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1) <7> [166.088160] [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [166.088429] [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1) <7> [166.088438] [drm:drm_dp_dual_mode_detect] DP dual mode HDMI ID: (err -6) <7> [166.088447] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:72:HDMI-A-1] disconnected <5> [166.089767] Setting dangerous option reset - tainting kernel <6> [166.090300] [IGT] kms_busy: starting subtest basic-flip-B <7> [166.096114] [drm:drm_mode_addfb2] [FB:81] <7> [166.143190] [drm:drm_mode_setcrtc] [CRTC:39:pipe A] <7> [166.159833] [drm:intel_edp_backlight_off [i915]] <7> [166.363312] [drm:intel_panel_actually_set_backlight [i915]] set backlight PWM = 0 <7> [166.363623] [drm:intel_disable_pipe [i915]] disabling pipe A <7> [166.378784] [drm:intel_edp_panel_off.part.31 [i915]] Turn eDP port A panel power off <7> [166.378892] [drm:intel_edp_panel_off.part.31 [i915]] Wait for panel power off time <7> [166.378990] [drm:wait_panel_status [i915]] mask b0000000 value 00000000 status a0000003 control 00000000 <7> [166.431185] [drm:wait_panel_status [i915]] Wait complete <7> [166.431319] [drm:ilk_hpd_irq_handler [i915]] hotplug event received, stat 0x08000000, dig 0x00000012, pins 0x00000010, long 0x00000010 <7> [166.431433] [drm:intel_disable_shared_dpll [i915]] disable LCPLL 1350 (active 1, on? 1) for crtc 39 <7> [166.431547] [drm:intel_hpd_irq_handler [i915]] digital hpd port A - long <7> [166.431653] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 0 <7> [166.431757] [drm:intel_disable_shared_dpll [i915]] disabling LCPLL 1350 <7> [166.432012] [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP port A <7> [166.432944] [drm:intel_atomic_commit_tail [i915]] [ENCODER:64:DDI A] <7> [166.433375] [drm:intel_atomic_commit_tail [i915]] [ENCODER:71:DDI B] <7> [166.433497] [drm:verify_connector_state.isra.87 [i915]] [CONNECTOR:65:eDP-1] <7> [166.433574] [drm:verify_single_dpll_state.isra.88 [i915]] WRPLL 1 <7> [166.433645] [drm:verify_single_dpll_state.isra.88 [i915]] WRPLL 2 <7> [166.433714] [drm:verify_single_dpll_state.isra.88 [i915]] SPLL <7> [166.433787] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 810 <7> [166.433856] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 1350 <7> [166.433926] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 2700 <7> [166.434191] [drm:intel_atomic_commit_tail [i915]] [CRTC:39:pipe A] <7> [166.435631] [drm:drm_mode_setcrtc] [CRTC:51:pipe B] <7> [166.435682] [drm:drm_mode_setcrtc] [CONNECTOR:65:eDP-1] <7> [166.435845] [drm:intel_atomic_check [i915]] [CONNECTOR:65:eDP-1] checking for sink bpp constrains <7> [166.435916] [drm:intel_atomic_check [i915]] clamping display bpp (was 36) to EDID reported max of 18 <7> [166.435989] [drm:intel_dp_compute_config [i915]] DP link computation with max lane count 1 max rate 270000 max bpp 18 pixel clock 76420KHz <7> [166.436097] [drm:intel_dp_compute_config [i915]] DP lane count 1 clock 270000 bpp 18 <7> [166.436170] [drm:intel_dp_compute_config [i915]] DP link rate required 171945 available 270000 <7> [166.436246] [drm:intel_atomic_check [i915]] hw max bpp: 36, pipe bpp: 18, dithering: 1 <7> [166.436320] [drm:intel_dump_pipe_config [i915]] [CRTC:51:pipe B][modeset] <7> [166.436391] [drm:intel_dump_pipe_config [i915]] output_types: EDP (0x100) <7> [166.436461] [drm:intel_dump_pipe_config [i915]] cpu_transcoder: EDP, pipe bpp: 18, dithering: 1 <7> [166.436531] [drm:intel_dump_pipe_config [i915]] dp m_n: lanes: 1; gmch_m: 2671072, gmch_n: 4194304, link_m: 148392, link_n: 524288, tu: 64 <7> [166.436601] [drm:intel_dump_pipe_config [i915]] audio: 0, infoframes: 0 <7> [166.436672] [drm:intel_dump_pipe_config [i915]] requested mode: <7> [166.436682] [drm:drm_mode_debug_printmodeline] Modeline 0:"1366x768" 60 76420 1366 1502 1532 1592 768 776 788 800 0x48 0xa <7> [166.436749] [drm:intel_dump_pipe_config [i915]] adjusted mode: <7> [166.436758] [drm:drm_mode_debug_printmodeline] Modeline 0:"1366x768" 60 76420 1366 1502 1532 1592 768 776 788 800 0x48 0xa <7> [166.436826] [drm:intel_dump_pipe_config [i915]] crtc timings: 76420 1366 1502 1532 1592 768 776 788 800, type: 0x48 flags: 0xa <7> [166.436896] [drm:intel_dump_pipe_config [i915]] port clock: 270000, pipe src size: 1366x768, pixel rate 76420 <7> [166.436966] [drm:intel_dump_pipe_config [i915]] pch pfit: pos: 0x00000000, size: 0x00000000, disabled <7> [166.437067] [drm:intel_dump_pipe_config [i915]] ips: 0, double wide: 0 <7> [166.437138] [drm:intel_dump_pipe_config [i915]] dpll_hw_state: wrpll: 0x0 spll: 0x0 <7> [166.437209] [drm:intel_dump_pipe_config [i915]] planes on this crtc <7> [166.437283] [drm:intel_dump_pipe_config [i915]] [PLANE:40:primary B] disabled, scaler_id = 0 <7> [166.437356] [drm:intel_dump_pipe_config [i915]] [PLANE:43:sprite B] disabled, scaler_id = 0 <7> [166.437431] [drm:intel_dump_pipe_config [i915]] [PLANE:48:cursor B] disabled, scaler_id = 0 <7> [166.437539] [drm:intel_reference_shared_dpll [i915]] using LCPLL 1350 for pipe B <7> [166.440355] [drm:intel_atomic_commit_tail [i915]] [ENCODER:64:DDI A] <7> [166.440428] [drm:intel_atomic_commit_tail [i915]] [ENCODER:71:DDI B] <7> [166.440499] [drm:verify_single_dpll_state.isra.88 [i915]] WRPLL 1 <7> [166.440572] [drm:verify_single_dpll_state.isra.88 [i915]] WRPLL 2 <7> [166.440641] [drm:verify_single_dpll_state.isra.88 [i915]] SPLL <7> [166.440714] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 810 <7> [166.440784] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 1350 <7> [166.440895] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 2700 <7> [166.441383] [drm:intel_enable_shared_dpll [i915]] enable LCPLL 1350 (active 2, on? 0) for crtc 51 <7> [166.441454] [drm:intel_enable_shared_dpll [i915]] enabling LCPLL 1350 <7> [166.441532] [drm:edp_panel_on [i915]] Turn eDP port A panel power on <7> [166.441603] [drm:wait_panel_power_cycle [i915]] Wait for panel power cycle <7> [167.083324] [drm:wait_panel_status [i915]] mask b800000f value 00000000 status 00000000 control 00000000 <7> [167.083488] [drm:wait_panel_status [i915]] Wait complete <7> [167.083644] [drm:edp_panel_on [i915]] Wait for panel power on <7> [167.083802] [drm:wait_panel_status [i915]] mask b000000f value 80000008 status 9000000a control 00000003 <7> [167.158714] [drm:ilk_hpd_irq_handler [i915]] hotplug event received, stat 0x08000000, dig 0x00000012, pins 0x00000010, long 0x00000010 <7> [167.158868] [drm:intel_hpd_irq_handler [i915]] digital hpd port A - long <7> [167.159015] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 1 <7> [167.159293] [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP port A <7> [167.285181] [drm:wait_panel_status [i915]] Wait complete <7> [167.285489] [drm:edp_panel_vdd_on [i915]] Turning eDP port A VDD on <7> [167.285708] [drm:edp_panel_vdd_on [i915]] PP_STATUS: 0x80000008 PP_CONTROL: 0x0000000b <7> [167.286815] [drm:intel_dp_start_link_train [i915]] Using LINK_BW_SET value 0a <7> [167.287931] [drm:intel_dp_set_signal_levels [i915]] Using signal levels 00000000 <7> [167.288126] [drm:intel_dp_set_signal_levels [i915]] Using vswing level 0 <7> [167.288256] [drm:intel_dp_set_signal_levels [i915]] Using pre-emphasis level 0 <7> [167.288381] [drm:intel_dp_program_link_training_pattern [i915]] Using DP training pattern TPS1 <7> [167.289907] [drm:intel_dp_start_link_train [i915]] clock recovery OK <7> [167.290036] [drm:intel_dp_program_link_training_pattern [i915]] Using DP training pattern TPS2 <7> [167.291750] [drm:intel_dp_start_link_train [i915]] Channel EQ done. DP Training successful <7> [167.291824] [drm:intel_dp_start_link_train [i915]] [CONNECTOR:65:eDP-1] Link Training Passed at Link Rate = 270000, Lane count = 1 <7> [167.292171] [drm:intel_enable_pipe [i915]] enabling pipe B <7> [167.292493] [drm:intel_edp_backlight_on [i915]] <7> [167.292562] [drm:intel_panel_enable_backlight [i915]] pipe B <7> [167.292640] [drm:intel_panel_actually_set_backlight [i915]] set backlight PWM = 937 <7> [167.499269] [drm:intel_enable_ddi [i915]] Panel doesn't support DRRS <7> [167.509315] [drm:verify_connector_state.isra.87 [i915]] [CONNECTOR:65:eDP-1] <7> [167.509418] [drm:intel_atomic_commit_tail [i915]] [CRTC:51:pipe B] <7> [167.509520] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 1350 <7> [167.510782] [drm:drm_mode_setcrtc] [CRTC:63:pipe C] <7> [167.526307] [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe B <7> [167.531990] [drm:drm_mode_addfb2] [FB:80] <7> [168.226785] [drm:intel_edp_backlight_off [i915]] <7> [168.435278] [drm:intel_panel_actually_set_backlight [i915]] set backlight PWM = 0 <7> [168.435463] [drm:intel_disable_pipe [i915]] disabling pipe B <7> [168.443285] [drm:intel_edp_panel_off.part.31 [i915]] Turn eDP port A panel power off <7> [168.443362] [drm:intel_edp_panel_off.part.31 [i915]] Wait for panel power off time <7> [168.443442] [drm:wait_panel_status [i915]] mask b0000000 value 00000000 status a0000003 control 00000000 <7> [168.495252] [drm:wait_panel_status [i915]] Wait complete <7> [168.495387] [drm:intel_disable_shared_dpll [i915]] disable LCPLL 1350 (active 2, on? 1) for crtc 51 <7> [168.495500] [drm:intel_disable_shared_dpll [i915]] disabling LCPLL 1350 <7> [168.495624] [drm:intel_atomic_commit_tail [i915]] [ENCODER:64:DDI A] <7> [168.495737] [drm:intel_atomic_commit_tail [i915]] [ENCODER:71:DDI B] <7> [168.495830] [drm:ilk_hpd_irq_handler [i915]] hotplug event received, stat 0x08000000, dig 0x00000012, pins 0x00000010, long 0x00000010 <7> [168.495937] [drm:intel_hpd_irq_handler [i915]] digital hpd port A - long <7> [168.496043] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 0 <7> [168.496223] [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP port A <7> [168.496833] [drm:verify_connector_state.isra.87 [i915]] [CONNECTOR:65:eDP-1] <7> [168.496958] [drm:verify_single_dpll_state.isra.88 [i915]] WRPLL 1 <7> [168.497148] [drm:verify_single_dpll_state.isra.88 [i915]] WRPLL 2 <7> [168.497261] [drm:verify_single_dpll_state.isra.88 [i915]] SPLL <7> [168.497375] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 810 <7> [168.497483] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 1350 <7> [168.497590] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 2700 <7> [168.497759] [drm:intel_atomic_commit_tail [i915]] [CRTC:51:pipe B] <5> [168.499471] Setting dangerous option reset - tainting kernel <5> [168.500634] Setting dangerous option reset - tainting kernel <6> [168.501189] [IGT] kms_busy: exiting, ret=0 <7> [168.507477] [drm:intel_atomic_check [i915]] [CONNECTOR:65:eDP-1] checking for sink bpp constrains <7> [168.507549] [drm:intel_atomic_check [i915]] clamping display bpp (was 36) to EDID reported max of 18 <7> [168.507622] [drm:intel_dp_compute_config [i915]] DP link computation with max lane count 1 max rate 270000 max bpp 18 pixel clock 76420KHz <7> [168.507692] [drm:intel_dp_compute_config [i915]] DP lane count 1 clock 270000 bpp 18 <7> [168.507761] [drm:intel_dp_compute_config [i915]] DP link rate required 171945 available 270000 <7> [168.507834] [drm:intel_atomic_check [i915]] hw max bpp: 36, pipe bpp: 18, dithering: 1 <7> [168.507904] [drm:intel_dump_pipe_config [i915]] [CRTC:39:pipe A][modeset] <7> [168.507976] [drm:intel_dump_pipe_config [i915]] output_types: EDP (0x100) <7> [168.508400] [drm:intel_dump_pipe_config [i915]] cpu_transcoder: EDP, pipe bpp: 18, dithering: 1 <7> [168.508471] [drm:intel_dump_pipe_config [i915]] dp m_n: lanes: 1; gmch_m: 2671072, gmch_n: 4194304, link_m: 148392, link_n: 524288, tu: 64 <7> [168.508540] [drm:intel_dump_pipe_config [i915]] audio: 0, infoframes: 0 <7> [168.508608] [drm:intel_dump_pipe_config [i915]] requested mode: <7> [168.508619] [drm:drm_mode_debug_printmodeline] Modeline 0:"1366x768" 60 76420 1366 1502 1532 1592 768 776 788 800 0x48 0xa <7> [168.508687] [drm:intel_dump_pipe_config [i915]] adjusted mode: <7> [168.508696] [drm:drm_mode_debug_printmodeline] Modeline 0:"1366x768" 60 76420 1366 1502 1532 1592 768 776 788 800 0x48 0xa <7> [168.508767] [drm:intel_dump_pipe_config [i915]] crtc timings: 76420 1366 1502 1532 1592 768 776 788 800, type: 0x48 flags: 0xa <7> [168.508837] [drm:intel_dump_pipe_config [i915]] port clock: 270000, pipe src size: 1366x768, pixel rate 76420 <7> [168.508907] [drm:intel_dump_pipe_config [i915]] pch pfit: pos: 0x00000000, size: 0x00000000, disabled <7> [168.508976] [drm:intel_dump_pipe_config [i915]] ips: 0, double wide: 0 <7> [168.509584] [drm:intel_dump_pipe_config [i915]] dpll_hw_state: wrpll: 0x0 spll: 0x0 <7> [168.509656] [drm:intel_dump_pipe_config [i915]] planes on this crtc <7> [168.509726] [drm:intel_dump_pipe_config [i915]] [PLANE:28:primary A] disabled, scaler_id = 0 <7> [168.509796] [drm:intel_dump_pipe_config [i915]] [PLANE:31:sprite A] disabled, scaler_id = 0 <7> [168.509865] [drm:intel_dump_pipe_config [i915]] [PLANE:36:cursor A] disabled, scaler_id = 0 <7> [168.509948] [drm:intel_reference_shared_dpll [i915]] using LCPLL 1350 for pipe A <7> [168.510454] [drm:intel_atomic_commit_tail [i915]] [ENCODER:64:DDI A] <7> [168.510525] [drm:intel_atomic_commit_tail [i915]] [ENCODER:71:DDI B] <7> [168.510594] [drm:verify_single_dpll_state.isra.88 [i915]] WRPLL 1 <7> [168.510669] [drm:verify_single_dpll_state.isra.88 [i915]] WRPLL 2 <7> [168.510744] [drm:verify_single_dpll_state.isra.88 [i915]] SPLL <7> [168.510817] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 810 <7> [168.510886] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 1350 <7> [168.510955] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 2700 <7> [168.511341] [drm:intel_enable_shared_dpll [i915]] enable LCPLL 1350 (active 1, on? 0) for crtc 39 <7> [168.511411] [drm:intel_enable_shared_dpll [i915]] enabling LCPLL 1350 <7> [168.511491] [drm:edp_panel_on [i915]] Turn eDP port A panel power on <7> [168.511562] [drm:wait_panel_power_cycle [i915]] Wait for panel power cycle <7> [169.131343] [drm:wait_panel_status [i915]] mask b800000f value 00000000 status 00000000 control 00000000 <7> [169.131503] [drm:wait_panel_status [i915]] Wait complete <7> [169.131658] [drm:edp_panel_on [i915]] Wait for panel power on <7> [169.131822] [drm:wait_panel_status [i915]] mask b000000f value 80000008 status 9000000a control 00000003 <7> [169.206670] [drm:ilk_hpd_irq_handler [i915]] hotplug event received, stat 0x08000000, dig 0x00000012, pins 0x00000010, long 0x00000010 <7> [169.206799] [drm:intel_hpd_irq_handler [i915]] digital hpd port A - long <7> [169.206926] [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 1 <7> [169.207121] [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP port A <7> [169.333896] [drm:wait_panel_status [i915]] Wait complete <7> [169.334342] [drm:edp_panel_vdd_on [i915]] Turning eDP port A VDD on <7> [169.334424] [drm:edp_panel_vdd_on [i915]] PP_STATUS: 0x80000008 PP_CONTROL: 0x0000000b <7> [169.335325] [drm:intel_dp_start_link_train [i915]] Using LINK_BW_SET value 0a <7> [169.335792] [drm:intel_dp_set_signal_levels [i915]] Using signal levels 00000000 <7> [169.335860] [drm:intel_dp_set_signal_levels [i915]] Using vswing level 0 <7> [169.335929] [drm:intel_dp_set_signal_levels [i915]] Using pre-emphasis level 0 <7> [169.336261] [drm:intel_dp_program_link_training_pattern [i915]] Using DP training pattern TPS1 <7> [169.337298] [drm:intel_dp_start_link_train [i915]] clock recovery OK <7> [169.337453] [drm:intel_dp_program_link_training_pattern [i915]] Using DP training pattern TPS2 <7> [169.338541] [drm:intel_dp_start_link_train [i915]] Channel EQ done. DP Training successful <7> [169.338615] [drm:intel_dp_start_link_train [i915]] [CONNECTOR:65:eDP-1] Link Training Passed at Link Rate = 270000, Lane count = 1 <7> [169.338962] [drm:intel_enable_pipe [i915]] enabling pipe A <7> [169.339339] [drm:intel_edp_backlight_on [i915]] <7> [169.339408] [drm:intel_panel_enable_backlight [i915]] pipe A <7> [169.339489] [drm:intel_panel_actually_set_backlight [i915]] set backlight PWM = 937 <7> [169.547339] [drm:intel_enable_ddi [i915]] Panel doesn't support DRRS <7> [169.573123] [drm:verify_connector_state.isra.87 [i915]] [CONNECTOR:65:eDP-1] <7> [169.573263] [drm:intel_atomic_commit_tail [i915]] [CRTC:39:pipe A] <7> [169.573380] [drm:verify_single_dpll_state.isra.88 [i915]] LCPLL 1350 <6> [169.573751] Console: switching to colour frame buffer device 170x48 |