Results for igt@kms_pm_dc@deep-pkgc

Result: Pass

i915_display_info4 igt_runner4 results4.json results4-xe-load.json guc_logs4.tar i915_display_info_post_exec4 serial_data4 boot4 dmesg4

DetailValue
Duration 6.50 seconds
Hostname
shard-lnl-3
Igt-Version
IGT-Version: 2.4-g22222b7d9 (x86_64) (Linux: 7.1.0-rc3-lgci-xe-xe-pw-166595v1-debug+ x86_64)
Out
Using IGT_SRANDOM=1778860051 for randomisation
Opened device: /dev/dri/card1
DMC: fw loaded: yes
Starting subtest: deep-pkgc
Subtest deep-pkgc: SUCCESS (6.501s)
Err
Starting subtest: deep-pkgc
Subtest deep-pkgc: SUCCESS (6.501s)
Dmesg
<6> [430.981962] Console: switching to colour dummy device 80x25
<6> [430.982305] [IGT] kms_pm_dc: executing
<7> [430.989328] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [430.989338] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [430.989503] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [430.989612] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [430.989925] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [430.989930] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [430.990073] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [430.990173] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [430.990435] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [430.990438] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [430.990562] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [430.990656] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<7> [430.990919] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1]
<7> [430.990923] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:393:eDP-1]
<7> [430.991383] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [430.991706] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [430.991820] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [430.991934] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [430.992057] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [430.992063] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [430.992065] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [430.992066] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [430.992069] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [430.992071] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [430.992072] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD monitor
<5> [430.992075] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [430.992076] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD size 20, SAD count 0
<5> [430.992079] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [430.992092] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] VRR capable: yes
<7> [430.992190] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [430.992275] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [430.992588] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [430.992590] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [430.992593] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [430.992642] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1] probed modes:
<7> [430.992646] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [430.992650] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [430.992685] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [430.992690] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [430.992845] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [430.992855] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [430.992859] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [430.992991] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [430.993000] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [430.993002] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [430.993118] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<6> [430.994346] [IGT] kms_pm_dc: starting subtest deep-pkgc
<7> [430.995259] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [430.995361] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [430.995453] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [430.995543] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [430.995632] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [430.995746] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [430.995861] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [430.995972] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [430.996067] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [430.996153] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [430.996240] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [430.996326] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [430.996411] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [430.996497] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [430.996584] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [430.996674] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [430.996781] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [430.996885] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [430.996988] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [430.997076] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [430.997156] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [430.997235] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [430.997314] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [430.997393] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [430.997472] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [430.997554] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [430.997632] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [430.997732] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [430.997833] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [430.997933] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [430.998020] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [430.998101] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [430.998178] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [430.998253] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [430.998330] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [430.998410] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [430.998486] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [430.998561] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [430.998635] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [430.998733] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:151:pipe A] releasing DPLL 0
<7> [430.998875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [430.998967] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [430.999045] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [430.999119] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [430.999184] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [430.999242] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [430.999298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [430.999354] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [430.999421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [430.999519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [430.999617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [430.999732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [430.999843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [430.999952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [431.000046] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [431.000146] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [431.000230] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [431.000313] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [431.000395] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [431.000492] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: no [modeset]
<7> [431.000584] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [NOFB], visible: no
<7> [431.000672] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [431.000780] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [431.000888] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [431.000989] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [431.001076] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [431.001209] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [431.001317] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [431.001460] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [431.002037] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [431.002147] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [431.206939] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 0
<7> [431.207410] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [431.217026] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power off
<7> [431.217339] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [431.217472] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [431.217664] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [431.217977] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [431.270050] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [431.270567] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [431.278913] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [431.279391] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:151:pipe A]
<7> [431.279436] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [431.279984] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [431.280957] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [431.281446] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [431.281975] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [431.282331] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [431.282659] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [431.282962] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [431.283254] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [431.283604] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [431.283981] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [431.284268] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [431.284552] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [431.284868] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [431.285152] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [431.285443] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [431.285836] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [431.286164] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [431.286468] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:402:DP-1]
<7> [431.286848] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:414:DP-2]
<7> [431.287194] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:422:DP-3]
<7> [431.287595] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [431.287954] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [431.288242] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [431.288750] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [431.289164] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xaa000000)
<7> [431.289616] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [431.289982] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [431.290341] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [431.290595] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [431.290978] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800010 0x9a00071)
<7> [431.294285] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [431.309363] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [431.309707] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [431.309683] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [431.309964] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [431.310055] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [431.310218] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [431.310374] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [431.342291] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [431.372331] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [431.372684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [431.373474] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [431.373517] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:393:eDP-1]
<7> [431.373612] xe 0000:00:02.0: [drm:compute_baseline_pipe_bpp [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [431.373772] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [431.373890] xe 0000:00:02.0: [drm:intel_dp_compute_output_format [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [431.374016] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [431.374144] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A]
<7> [431.374271] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [431.374399] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [431.374519] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [431.374653] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [431.374770] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [431.374883] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [431.374994] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [431.375106] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [431.375219] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [431.375334] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [431.375448] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [431.375566] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [431.375696] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [431.375815] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [431.375929] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [431.376042] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [431.376156] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [431.376280] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [431.376394] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [431.376503] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [431.376613] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [431.376730] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [431.376840] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [431.376949] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [431.377059] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [431.377170] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [431.377286] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [431.377404] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [431.377518] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [431.377654] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [431.377775] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [431.377883] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [431.377993] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [431.378104] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [431.378213] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [431.378320] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [431.378429] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [431.378536] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [431.378791] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [431.378970] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [431.379078] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [431.379204] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [431.379354] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [431.379450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [431.379527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [431.379605] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [431.379695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [431.379798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 1
<7> [431.379925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [431.380045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [431.380163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [431.380281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [431.380400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [431.380528] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [431.380698] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [431.380826] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [431.380943] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [431.381059] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [431.381209] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:151:pipe A] allocated DPLL 0
<7> [431.381323] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:151:pipe A] reserving DPLL 0
<7> [431.381431] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [modeset]
<7> [431.381550] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [431.381675] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [431.381794] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [431.381911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [431.382031] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [431.382157] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [431.382284] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [431.382410] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [431.382535] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [431.382777] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [431.382897] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [431.383010] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum hblank: 0
<7> [431.383123] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [431.383236] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [431.383350] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [431.383463] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [431.383575] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [431.383696] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [431.383810] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [431.383923] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [431.384035] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [431.384150] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [431.384270] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [431.384387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [431.384509] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [431.384644] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [431.384769] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [431.384888] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [431.385004] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [431.385121] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pixel rate 347710, min cdclk 173855, min voltage level 0
<7> [431.385239] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [431.385354] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0, sharpness_strength: 0
<7> [431.385467] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe src: 2880x1800+0+0
<7> [431.385580] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [431.385703] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [431.385817] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [431.385932] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [431.386047] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [431.386160] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [431.386278] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [431.386396] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [431.386517] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [431.386650] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [431.386776] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [431.386893] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [431.387011] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [431.387130] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [431.387248] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [431.387365] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [431.387479] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [431.387593] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [431.387789] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [431.387906] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [431.388023] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [431.388144] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [431.388264] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [431.388387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [431.388511] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [431.388902] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [FB:430] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [431.389025] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [431.389138] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [431.389251] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [431.389364] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [431.389477] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [431.389595] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [431.389717] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [431.390646] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [431.390952] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [431.391098] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [431.391297] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [431.391565] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [431.391724] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [431.391882] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [431.392005] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800071 0xc01b072)
<7> [431.392097] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [431.392222] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [431.392318] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [431.392436] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [431.392527] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [431.392627] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [431.392718] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [431.392805] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [431.392891] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [431.392977] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [431.393063] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [431.393149] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [431.393234] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [431.393321] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [431.393407] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [431.393493] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [431.393598] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [431.393776] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [431.393862] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [431.393975] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [431.395297] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:151:pipe A]
<7> [431.395403] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [431.397461] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power on
<7> [431.397601] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power cycle (382 ms remaining)
<7> [431.782894] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [431.841064] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [431.841547] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power on
<7> [431.841993] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [431.878500] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [431.878972] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [431.879307] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [431.879884] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [432.054801] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [432.054817] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [432.055178] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [432.055244] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [432.055301] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7> [432.055702] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [432.057818] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [432.059289] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [432.060060] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [432.061156] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [432.062470] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [432.063589] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Clock recovery OK
<7> [432.063938] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [432.065408] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [432.065770] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [432.066564] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [432.067052] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [432.067380] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [432.067795] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 4518
<7> [432.100607] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [432.102366] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [432.102781] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [432.112488] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:270:pipe B]
<7> [432.117260] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:389:pipe C]
<7> [432.152260] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [432.167471] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [432.167619] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:393:eDP-1]
<7> [432.169580] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [432.170039] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [432.170435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [432.170835] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [432.171223] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [432.202596] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [432.203031] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [432.203419] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [434.614518] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD off
<7> [434.614857] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067
<7> [437.185423] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [437.185762] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [437.186339] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [437.186791] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [437.187248] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [437.187667] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [437.188159] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [437.188568] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [437.188961] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [437.189393] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [437.189819] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [437.190289] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [437.190679] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [437.191050] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [437.191502] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [437.191868] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [437.192334] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [437.192729] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [437.193085] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [437.193467] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [437.193794] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [437.194164] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [437.194506] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [437.194826] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [437.195160] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [437.195483] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [437.195800] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [437.196200] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [437.196529] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [437.196848] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [437.197214] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [437.197573] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [437.197865] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [437.198163] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [437.198427] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [437.198689] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [437.198990] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [437.199291] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [437.199529] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [437.199755] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [437.199976] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:151:pipe A] releasing DPLL 0
<7> [437.200309] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [437.200513] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [437.200716] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [437.200900] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [437.201053] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [437.201230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [437.201377] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [437.201515] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [437.201678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [437.201881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [437.202078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [437.202298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [437.202498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [437.202672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [437.202845] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [437.203043] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [437.203235] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [437.203390] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [437.203544] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [437.203728] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: no [modeset]
<7> [437.203906] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [NOFB], visible: no
<7> [437.204063] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [437.204229] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [437.204371] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [437.204505] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [437.204637] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [437.204839] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [437.205620] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [437.205792] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [437.205993] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7> [437.206118] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f
<7> [437.206752] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [437.206867] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [437.414450] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 0
<7> [437.415024] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [437.424669] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power off
<7> [437.425102] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [437.425120] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [437.425521] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [437.425623] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [437.477735] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [437.478242] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [437.480286] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [437.480663] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:151:pipe A]
<7> [437.480701] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [437.481109] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [437.482092] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [437.482640] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [437.483180] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [437.483530] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [437.483866] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [437.484199] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [437.484551] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [437.484863] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [437.485174] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [437.485516] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [437.485805] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [437.486088] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [437.486430] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [437.486701] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [437.486970] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [437.487298] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [437.487628] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [437.487872] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [437.488113] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [437.488623] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [437.489017] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xaa000000)
<7> [437.489468] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [437.489768] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [437.490138] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [437.490418] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<6> [437.496233] [IGT] kms_pm_dc: finished subtest deep-pkgc, SUCCESS
<7> [437.497192] xe 0000:00:02.0: [drm:compute_baseline_pipe_bpp [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [437.497464] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [437.497698] xe 0000:00:02.0: [drm:intel_dp_compute_output_format [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [437.497941] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [437.498198] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A]
<7> [437.498436] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [437.498667] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [437.498883] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [437.499095] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [437.499328] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [437.499521] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [437.499710] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [437.499890] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [437.500069] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [437.500357] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [437.500524] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [437.500684] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [437.500836] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [437.500984] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [437.501139] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [437.501289] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [437.501434] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [437.501572] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [437.501706] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [437.501830] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [437.501953] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [437.502092] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [437.502413] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [437.502530] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [437.502641] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [437.502748] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [437.502852] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [437.502953] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [437.503053] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [437.503157] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [437.503255] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [437.503348] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [437.503440] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [437.503528] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [437.503616] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [437.503705] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [437.503791] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [437.503873] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [437.503956] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [437.504099] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [437.504210] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [437.504298] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [437.504377] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [437.504446] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [437.504508] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [437.504566] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [437.504623] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [437.504697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 1
<7> [437.504796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [437.504889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [437.504975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [437.505059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [437.505147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [437.505240] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [437.505384] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [437.505475] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [437.505558] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [437.505640] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [437.505741] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:151:pipe A] allocated DPLL 0
<7> [437.505824] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:151:pipe A] reserving DPLL 0
<7> [437.505912] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [modeset]
<7> [437.506001] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [437.506089] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [437.506324] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [437.506432] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [437.506527] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [437.506620] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [437.506701] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [437.506783] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [437.506863] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [437.506942] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [437.507022] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [437.507101] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum hblank: 0
<7> [437.507197] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [437.507298] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [437.507383] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [437.507463] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [437.507541] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [437.507620] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [437.507697] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [437.507775] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [437.507854] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [437.507933] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [437.508011] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [437.508089] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [437.508179] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [437.508254] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [437.508281] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [437.508383] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [437.508411] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [437.508464] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [437.508507] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [437.508543] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [437.508622] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pixel rate 347710, min cdclk 173855, min voltage level 0
<7> [437.508634] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [437.508699] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [437.508747] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspending
<7> [437.508777] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0, sharpness_strength: 0
<7> [437.508858] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe src: 2880x1800+0+0
<7> [437.508943] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [437.508989] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled
<7> [437.509028] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [437.509061] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspended
<7> [437.509112] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [437.509139] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspending
<7> [437.509212] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [437.509300] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [437.509333] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled
<7> [437.509382] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [437.509400] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspended
<7> [437.509460] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [437.509538] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [437.509614] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [437.509691] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [437.509774] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [437.509853] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [437.509929] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [437.510005] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [437.510081] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [437.510176] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [437.510275] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [437.510359] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [437.510434] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [437.510509] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [437.510583] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [437.510658] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [437.510733] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [437.510807] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [437.510882] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [437.510957] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [FB:394] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [437.511032] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [437.511107] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [437.511192] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [437.511281] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [437.511362] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [437.511439] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [437.511516] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [437.533734] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resuming
<7> [437.534176] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled
<7> [437.534946] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resumed
<7> [437.535022] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resuming
<7> [437.535320] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled
<7> [437.535396] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resumed
<7> [437.536177] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [437.536307] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [437.536569] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [437.536689] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [437.536983] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [437.537114] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [437.537243] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [437.537331] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [437.537422] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [437.537498] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [437.537572] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [437.537644] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [437.537715] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [437.537783] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [437.537851] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [437.537917] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [437.537983] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [437.538048] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [437.538112] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [437.538188] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [437.538256] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [437.538341] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [437.538489] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [437.538553] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [437.538645] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [437.540053] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:151:pipe A]
<7> [437.540172] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [437.541258] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power on
<7> [437.541344] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power cycle (440 ms remaining)
<7> [437.990319] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [438.031474] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [438.031827] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power on
<7> [438.032112] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [438.068598] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [438.069163] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [438.069666] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [438.070419] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [438.240559] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [438.240983] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7> [438.241425] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [438.243589] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [438.245181] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [438.246007] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [438.247322] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [438.248916] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [438.250221] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Clock recovery OK
<7> [438.250710] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [438.252333] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [438.252750] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [438.253621] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [438.254214] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [438.254636] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [438.255128] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 4518
<7> [438.287891] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [438.289649] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [438.290031] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [438.293262] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [438.293286] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [438.294533] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<6> [438.295251] [IGT] kms_pm_dc: exiting, ret=0
<7> [438.296281] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [438.296774] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [438.297633] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [438.298089] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [438.298672] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [438.299072] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [438.299623] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [438.301088] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [438.301711] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<6> [438.304793] Console: switching to colour frame buffer device 180x56
Created at 2026-05-15 16:26:23