Result:
i915_display_info10 igt_runner10 results10.json results10-xe-load.json guc_logs10.tar i915_display_info_post_exec10 serial_data10 boot10 dmesg10
| Detail | Value |
|---|---|
| Duration | 11.28 seconds |
| Hostname |
shard-lnl-8 |
| Igt-Version |
IGT-Version: 2.4-gd28bd0b9e (x86_64) (Linux: 7.1.0-rc3-lgci-xe-xe-pw-166108v2-debug+ x86_64) |
| Out |
Using IGT_SRANDOM=1778520167 for randomisation Opened device: /dev/dri/card1 Using monotonic timestamps Starting subtest: flip-vs-expired-vblank Starting dynamic subtest: A-eDP1 2880x1800: 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa Dynamic subtest A-eDP1: SUCCESS (11.281s) |
| Err |
Starting subtest: flip-vs-expired-vblank Starting dynamic subtest: A-eDP1 Dynamic subtest A-eDP1: SUCCESS (11.281s) |
| Dmesg |
<6> [506.494135] Console: switching to colour dummy device 80x25
<6> [506.494612] [IGT] kms_flip: executing
<7> [506.501509] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [506.501519] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [506.501684] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [506.501791] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [506.502086] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [506.502091] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [506.502242] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [506.502350] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [506.502605] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [506.502609] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [506.502747] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [506.502840] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<7> [506.503087] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1]
<7> [506.503091] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:393:eDP-1]
<7> [506.503215] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7> [506.503342] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f
<7> [506.503777] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [506.504097] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [506.504217] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [506.504458] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [506.504805] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [506.504817] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [506.504823] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [506.504826] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [506.504834] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [506.504842] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [506.504846] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD monitor
<5> [506.504855] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [506.504859] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD size 20, SAD count 0
<5> [506.504866] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [506.504892] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] VRR capable: yes
<7> [506.505248] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [506.505359] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [506.505691] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [506.505693] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [506.505694] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [506.505740] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1] probed modes:
<7> [506.505744] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [506.505748] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [506.505762] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [506.505766] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [506.505912] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [506.505922] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [506.505925] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [506.506054] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [506.506065] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [506.506069] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [506.506204] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<6> [506.506733] [IGT] kms_flip: starting subtest flip-vs-expired-vblank
<6> [506.507994] [IGT] kms_flip: starting dynamic subtest A-eDP1
<7> [506.508664] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [506.509161] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [506.584121] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [506.584328] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [506.584614] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [506.584828] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [506.585054] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [506.585252] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [506.585446] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [506.585629] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [506.585809] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [506.585988] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [506.586197] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [506.586364] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [506.586523] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [506.586685] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [506.586846] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [506.587004] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [506.587190] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [506.587337] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [506.587482] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [506.587623] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [506.587757] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [506.587889] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [506.588029] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [506.588158] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [506.588285] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [506.588409] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [506.588532] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [506.588646] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [506.588761] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [506.588874] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [506.588983] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [506.589109] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [506.589222] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [506.589330] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [506.589437] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [506.589545] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [506.589648] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [506.589750] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [506.589848] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [506.589948] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [506.590085] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:151:pipe A] releasing DPLL 0
<7> [506.590250] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [506.590342] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [506.590456] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [506.590538] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [506.590612] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [506.590681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [506.590756] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [506.590829] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [506.590928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [506.591058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [506.591187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [506.591298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [506.591403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [506.591495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [506.591586] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [506.591695] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [506.591788] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [506.591877] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [506.591966] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [506.592094] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: no [modeset]
<7> [506.592219] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [NOFB], visible: no
<7> [506.592330] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [506.592423] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [506.592513] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [506.592606] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [506.592711] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [506.592876] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [506.593601] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [506.593746] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [506.594449] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [506.594562] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [506.803224] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 0
<7> [506.803669] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [506.811394] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power off
<7> [506.811781] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [506.812155] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [506.864710] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [506.865026] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [506.867160] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [506.867498] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:151:pipe A]
<7> [506.867533] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [506.868921] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [506.869418] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [506.869896] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [506.870238] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [506.870532] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [506.870867] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [506.871170] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [506.871494] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [506.871811] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [506.872093] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [506.872410] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [506.872667] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [506.872922] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [506.873206] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [506.873463] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [506.873721] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [506.874138] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [506.874402] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [506.874649] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [506.875110] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [506.875495] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xaa000000)
<7> [506.875904] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [506.876227] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [506.876596] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [506.876857] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [506.877719] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:270:pipe B]
<7> [506.878071] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:389:pipe C]
<7> [506.878358] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [506.878417] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:393:eDP-1]
<7> [506.878583] xe 0000:00:02.0: [drm:compute_baseline_pipe_bpp [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [506.878961] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [506.879391] xe 0000:00:02.0: [drm:intel_dp_compute_output_format [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [506.879736] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [506.880151] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A]
<7> [506.880533] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [506.880834] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [506.881141] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [506.881474] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [506.881755] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [506.882023] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [506.882273] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [506.882519] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [506.882745] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [506.882966] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [506.883254] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [506.883462] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [506.883664] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [506.883858] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [506.884059] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [506.884245] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [506.884415] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [506.884611] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [506.884772] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [506.884936] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [506.885119] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [506.885278] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [506.885430] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [506.885577] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [506.885719] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [506.885860] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [506.885999] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [506.886166] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [506.886304] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [506.886441] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [506.886587] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [506.886714] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [506.886838] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [506.886962] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [506.887145] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [506.887264] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [506.887377] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [506.887489] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [506.887597] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [506.887746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [506.887842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [506.887959] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [506.888057] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [506.888138] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [506.888213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [506.888289] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 92, 297, 297, 297, 297, 297, 0, 0, 197, 92, 197
<7> [506.888362] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 183, 456, 456, 456, 456, 456, 0, 0, 198, 183, 198
<7> [506.888455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 1
<7> [506.888572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [506.888681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [506.888782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [506.888878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [506.888975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [506.889094] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [506.889218] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [506.889333] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [506.889430] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [506.889517] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [506.889615] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:151:pipe A] allocated DPLL 0
<7> [506.889699] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:151:pipe A] reserving DPLL 0
<7> [506.889783] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [modeset]
<7> [506.889867] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [506.889949] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [506.890045] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [506.890156] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [506.890264] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [506.890361] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [506.890448] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [506.890535] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [506.890629] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [506.890745] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [506.890853] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [506.890948] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum hblank: 0
<7> [506.891065] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [506.891187] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [506.891289] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [506.891387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [506.891485] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [506.891567] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [506.891650] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [506.891748] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [506.891857] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [506.891962] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [506.892066] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [506.892178] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [506.892290] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [506.892396] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [506.892486] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [506.892567] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [506.892648] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [506.892748] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pixel rate 347710, min cdclk 173855, min voltage level 0
<7> [506.892856] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [506.892957] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0, sharpness_strength: 0
<7> [506.893060] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe src: 2880x1800+0+0
<7> [506.893172] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [506.893284] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [506.893389] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [506.893487] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [506.893589] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [506.893692] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [506.893795] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [506.893894] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [506.893977] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [506.894083] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [506.894180] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [506.894275] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [506.894371] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [506.894465] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [506.894555] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [506.894655] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [506.894755] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [506.894838] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [506.894918] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [506.895006] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [506.895113] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [506.895221] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [506.895327] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [506.895418] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [506.895503] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [506.895583] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [FB:430] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x100000000000009, visible: yes
<7> [506.895674] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [506.895783] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [506.895888] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [506.895971] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [506.896088] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [506.896100] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [506.896201] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [506.896301] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [506.896316] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [506.896437] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [506.896700] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [506.896835] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [506.896986] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [506.897174] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [506.897300] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [506.897418] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [506.897536] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [506.897654] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [506.897739] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [506.897817] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [506.897898] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [506.897988] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [506.898098] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [506.898187] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [506.898276] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [506.898352] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [506.898438] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [506.898534] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [506.898622] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [506.898696] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [506.898785] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [506.898972] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [506.899070] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [506.899196] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [506.900036] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [506.900064] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:151:pipe A]
<7> [506.900185] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [506.900189] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [506.900316] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [506.900468] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [506.902222] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power on
<7> [506.902334] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power cycle (466 ms remaining)
<7> [507.371170] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [507.473041] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [507.473392] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power on
<7> [507.473664] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [507.510265] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [507.510592] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [507.510866] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [507.511530] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [507.555186] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [507.555272] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [507.555411] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [507.679512] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [507.679847] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7> [507.680189] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [507.682139] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [507.683594] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [507.684228] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [507.685231] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [507.686449] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [507.687453] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Clock recovery OK
<7> [507.687776] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [507.689231] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [507.689537] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [507.690258] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [507.690723] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [507.691091] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [507.691556] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 4518
<7> [507.724498] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [507.726087] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [507.726374] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [510.244003] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD off
<7> [510.244347] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067
<7> [517.756088] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [517.758424] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [517.758518] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:35:plane 1A] because [FB:430] is removed
<7> [517.758621] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [517.758888] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [517.759090] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [517.759278] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 92, 297, 297, 297, 297, 297, 0, 0, 197, 92, 197 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [517.759458] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 183, 456, 456, 456, 456, 456, 0, 0, 198, 183, 198 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [517.759722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [517.759993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [517.760286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [517.760568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [517.760837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [517.761101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [517.761816] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [517.772618] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7> [517.772929] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f
<6> [517.790200] [IGT] kms_flip: finished subtest A-eDP1, SUCCESS
|