Results for igt@kms_dp_link_training@uhbr-sst

Result: Skip

i915_display_info20 igt_runner20 results20.json results20-xe-load.json guc_logs20.tar i915_display_info_post_exec20 serial_data20 boot20 dmesg20

DetailValue
Duration 0.00 seconds
Hostname 
shard-lnl-3
Igt-Version 
IGT-Version: 2.4-g3ef61dd87 (x86_64) (Linux: 7.1.0-rc2-lgci-xe-xe-pw-165914v1-debug+ x86_64)
Out 
Using IGT_SRANDOM=1777924783 for randomisation
Opened device: /dev/dri/card0
Starting subtest: uhbr-sst
Skipping non-DisplayPort output eDP-1
----------------------------------------------------
Test requirement not met in function __igt_unique____real_main301, file ../tests/intel/kms_dp_link_training.c:323:
Test requirement: test_link_rate(&data, false, true)
Didn't find any SST output with UHBR rates.
Subtest uhbr-sst: SKIP (0.000s)
Err 
Starting subtest: uhbr-sst
Subtest uhbr-sst: SKIP (0.000s)
Dmesg
<6> [265.141919] Console: switching to colour dummy device 80x25
<6> [265.142291] [IGT] kms_dp_link_training: executing
<7> [265.322080] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [265.328175] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [265.331416] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [265.332996] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [265.334940] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [265.337034] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [265.338858] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Clock recovery OK
<7> [265.339341] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [265.341238] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [265.342018] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [265.343223] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [265.343808] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [265.344178] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [265.344584] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 4518
<7> [265.377309] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [265.381074] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [265.382196] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [265.384745] xe 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [xe]] pipe has 30 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7> [265.392482] xe 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [265.392583] xe 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [265.405197] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [265.405685] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [265.406029] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [265.411666] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [265.411686] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [265.411981] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [265.412411] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [265.412417] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [265.412616] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [265.412985] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [265.412990] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [265.413173] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<7> [265.413487] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1]
<7> [265.413491] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:393:eDP-1]
<7> [265.413986] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [265.414311] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [265.414428] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [265.414542] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [265.414726] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [265.414747] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [265.414756] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [265.414762] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [265.414777] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [265.414790] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [265.414798] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD monitor
<5> [265.414813] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [265.414820] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD size 20, SAD count 0
<5> [265.414833] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [265.414873] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] VRR capable: yes
<7> [265.415303] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [265.415644] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [265.415955] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [265.415957] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [265.415958] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [265.416002] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1] probed modes:
<7> [265.416006] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [265.416010] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [265.416023] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [265.416027] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [265.416188] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [265.416200] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [265.416203] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [265.416333] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [265.416343] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [265.416347] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [265.416465] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<6> [265.416820] [IGT] kms_dp_link_training: starting subtest uhbr-sst
<6> [265.417217] [IGT] kms_dp_link_training: finished subtest uhbr-sst, SKIP
<7> [265.418012] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [265.418153] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [265.427173] xe 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [265.427219] xe 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [265.428849] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1]
<7> [265.428865] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:393:eDP-1]
<7> [265.429800] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [265.432424] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [265.432920] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [265.433373] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [265.434660] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [265.434680] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [265.434685] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [265.434687] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [265.434694] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [265.434698] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [265.434701] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD monitor
<5> [265.434713] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [265.434716] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD size 20, SAD count 0
<5> [265.434721] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [265.434780] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] VRR capable: yes
<7> [265.435727] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [265.435895] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [265.436733] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [265.436748] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [265.436755] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [265.436946] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1] probed modes:
<7> [265.436982] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [265.437000] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [265.437019] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [265.437039] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [265.437724] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [265.437748] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [265.437765] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [265.437975] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [265.437982] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [265.437987] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [265.438183] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<7> [265.438190] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:393:eDP-1] enabled? yes
<7> [265.438198] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:402:DP-1] enabled? no
<7> [265.438204] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:414:DP-2] enabled? no
<7> [265.438208] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:422:DP-3] enabled? no
<7> [265.438594] xe 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [265.438642] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:393:eDP-1] found preferred mode: 2880x1800
<7> [265.438647] xe 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 2880x1800 config
<7> [265.438703] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:151:pipe A] desired mode 2880x1800 set (0,0)
<7> [265.443846] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [265.444756] [IGT] kms_dp_link_training: exiting, ret=77
<6> [265.448340] Console: switching to colour frame buffer device 180x56
Created at 2026-05-04 20:28:00