Oops#1 Part20
<7>[   52.720731] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding eDP connector on [ENCODER:392:DDI A/PHY A]
<7>[   52.721151] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel type (VBT): 2
<7>[   52.721300] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Selected panel type (VBT): 2
<7>[   52.721453] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] DRRS supported mode is seamless
<7>[   52.721616] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7>[   52.721786] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] VBT initial LVDS value 300
<7>[   52.721946] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel manufacturer name: MS_, product code: 3, serial number: 3, year of manufacture: 2002
<7>[   52.722094] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel name: LFP_PanelName
<7>[   52.722238] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Seamless DRRS min refresh rate: 0 Hz
<7>[   52.722378] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7>[   52.722541] xe 0000:00:02.0: [drm:intel_pps_init [xe]] [ENCODER:392:DDI A/PHY A] initial power sequencer: PPS 0
<7>[   52.722864] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] bios power_up 1 backlight_on 1 backlight_off 1 power_down 500 power_cycle 5000
<7>[   52.722997] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000
Oops#1 Part19
<7>[   52.723115] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100
<7>[   52.723223] xe 0000:00:02.0: [drm:pps_init_delays [xe]] panel power up delay 200, power down delay 50, power cycle delay 500
<7>[   52.723331] xe 0000:00:02.0: [drm:pps_init_delays [xe]] backlight on delay 1, off delay 200
<6>[   52.723735] xe 0000:00:02.0: [drm] Finished loading DMC firmware i915/xe2lpd_dmc.bin (v2.29)
<7>[   52.723801] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7>[   52.723993] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7>[   52.725396] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7>[   52.725542] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f
<7>[   52.749612] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7>[   52.761609] xe 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID  HW-rev 7.3 SW-rev 0.0 quirks 0x0000
<7>[   52.785597] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] eDP DPCD: 05 83 85 04 1e
<7>[   52.821588] xe 0000:00:02.0: [drm:intel_psr_init_dpcd [xe]] eDP panel supports PSR version 3
<7>[   52.833587] xe 0000:00:02.0: [drm:intel_psr_init_dpcd [xe]] PSR2 supported