<5>[ 0.000000] Linux version 6.18.0-rc4-lgci-xe-xe-pw-155951v4+ (builder@lgci) (gcc (Ubuntu 13.3.0-6ubuntu2~24.04) 13.3.0, GNU ld (GNU Binutils for Ubuntu) 2.42) #1 SMP PREEMPT_DYNAMIC Sat Nov 8 02:01:17 UTC 2025 <6>[ 0.000000] Command line: BOOT_IMAGE=/boot/drm_intel root=/dev/nvme0n1p2 rootwait fsck.repair=yes nmi_watchdog=panic,auto panic=5 softdog.soft_panic=5 log_buf_len=1M trace_clock=global snd_hda_intel.probe_mask=0x104 xe.force_probe=* i915.force_probe=* drm.debug=0xe modprobe.blacklist=xe,i915,ast initcall_blacklist=simpledrm_platform_driver_init ro <6>[ 0.000000] KERNEL supported cpus: <6>[ 0.000000] Intel GenuineIntel <6>[ 0.000000] AMD AuthenticAMD <6>[ 0.000000] Hygon HygonGenuine <6>[ 0.000000] Centaur CentaurHauls <6>[ 0.000000] zhaoxin Shanghai <6>[ 0.000000] x86/tme: not enabled by BIOS <6>[ 0.000000] x86/split lock detection: #AC: crashing the kernel on kernel split_locks and warning on user-space split_locks <6>[ 0.000000] BIOS-provided physical RAM map: <6>[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009efff] usable <6>[ 0.000000] BIOS-e820: [mem 0x000000000009f000-0x00000000000fffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000006cac0fff] usable <6>[ 0.000000] BIOS-e820: [mem 0x000000006cac1000-0x000000006fe67fff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x000000006fe68000-0x000000006ff4ffff] ACPI NVS <6>[ 0.000000] BIOS-e820: [mem 0x000000006ff50000-0x000000006fffefff] ACPI data <6>[ 0.000000] BIOS-e820: [mem 0x000000006ffff000-0x000000006fffffff] usable <6>[ 0.000000] BIOS-e820: [mem 0x0000000070000000-0x00000000807fffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x00000000c0000000-0x00000000cfffffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x00000000fed20000-0x00000000fed7ffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x00000000ff200000-0x00000001044fffff] reserved <6>[ 0.000000] BIOS-e820: [mem 0x0000000104500000-0x000000087f7fffff] usable <6>[ 0.000000] NX (Execute Disable) protection: active <6>[ 0.000000] APIC: Static calls initialized <6>[ 0.000000] efi: EFI v2.7 by Intel <6>[ 0.000000] efi: ACPI=0x6fffe000 ACPI 2.0=0x6fffe014 SMBIOS=0x6cbc7000 MEMATTR=0x69916018 ESRT=0x68ff8518 MOKvar=0x6ccfb000 <6>[ 0.000000] efi: Remove mem261: MMIO range=[0xc0000000-0xcfffffff] (256MB) from e820 map <7>[ 0.000000] e820: remove [mem 0xc0000000-0xcfffffff] reserved <6>[ 0.000000] efi: Remove mem263: MMIO range=[0xff200000-0xffffffff] (14MB) from e820 map <7>[ 0.000000] e820: remove [mem 0xff200000-0xffffffff] reserved <6>[ 0.000000] SMBIOS 3.8 present. <6>[ 0.000000] DMI: Intel Corporation Lunar Lake Client Platform/LNL-M LP5 RVP1, BIOS LNLMFWI1.R00.3223.D99.2508051732 08/05/2025 <6>[ 0.000000] DMI: Memory slots populated: 8/8 <6>[ 0.000000] tsc: Detected 3100.000 MHz processor <6>[ 0.000000] tsc: Detected 3110.400 MHz TSC <7>[ 0.000009] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved <7>[ 0.000010] e820: remove [mem 0x000a0000-0x000fffff] usable <6>[ 0.000014] last_pfn = 0x87f800 max_arch_pfn = 0x400000000 <6>[ 0.000017] MTRR map: 6 entries (3 fixed + 3 variable; max 23), built from 10 variable MTRRs <6>[ 0.000019] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT <6>[ 0.000375] x2apic: enabled by BIOS, switching to x2apic ops <6>[ 0.000376] last_pfn = 0x70000 max_arch_pfn = 0x400000000 <6>[ 0.004876] esrt: Reserving ESRT space from 0x0000000068ff8518 to 0x0000000068ff8668. <7>[ 0.004884] e820: update [mem 0x68ff8000-0x68ff8fff] usable ==> reserved <6>[ 0.004902] Using GB pages for direct mapping <6>[ 0.005535] printk: log buffer data + meta data: 1048576 + 3670016 = 4718592 bytes <6>[ 0.005536] printk: early log buf free: 258832(98%) <6>[ 0.005537] Secure boot disabled <6>[ 0.005538] ACPI: Early table checksum verification disabled <6>[ 0.005542] ACPI: RSDP 0x000000006FFFE014 000024 (v02 INTEL ) <6>[ 0.005545] ACPI: XSDT 0x000000006FF70228 000194 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005549] ACPI: FACP 0x000000006FFAA000 000114 (v06 INTEL LNL 00000002 01000013) <6>[ 0.005552] ACPI: DSDT 0x000000006FFB6000 02555F (v02 INTEL LNL 00000002 01000013) <6>[ 0.005553] ACPI: FACS 0x000000006FEF1000 000040 <6>[ 0.005555] ACPI: SSDT 0x000000006FFFC000 000388 (v02 PmaxDv Pmax_Dev 00000001 INTL 20210930) <6>[ 0.005556] ACPI: SSDT 0x000000006FFFB000 0006AA (v02 PmRef Cpu0Ist 00003000 INTL 20210930) <6>[ 0.005558] ACPI: SSDT 0x000000006FFFA000 0005FB (v02 PmRef Cpu0Hwp 00003000 INTL 20210930) <6>[ 0.005559] ACPI: SSDT 0x000000006FFF9000 0001AB (v02 PmRef Cpu0Psd 00003000 INTL 20210930) <6>[ 0.005560] ACPI: SSDT 0x000000006FFF8000 000394 (v02 PmRef Cpu0Cst 00003001 INTL 20210930) <6>[ 0.005562] ACPI: SSDT 0x000000006FFF6000 001BAF (v02 PmRef ApIst 00003000 INTL 20210930) <6>[ 0.005563] ACPI: SSDT 0x000000006FFF4000 001620 (v02 PmRef ApHwp 00003000 INTL 20210930) <6>[ 0.005564] ACPI: SSDT 0x000000006FFF2000 001349 (v02 PmRef ApPsd 00003000 INTL 20210930) <6>[ 0.005566] ACPI: SSDT 0x000000006FFF1000 000FBB (v02 PmRef ApCst 00003000 INTL 20210930) <6>[ 0.005567] ACPI: SSDT 0x000000006FFED000 003BD7 (v02 CpuRef CpuSsdt 00003000 INTL 20210930) <6>[ 0.005568] ACPI: DTPR 0x000000006FFEC000 000090 (v01 00000000 00000000) <6>[ 0.005570] ACPI: SSDT 0x000000006FFEB000 000FE2 (v02 INTEL PDatTabl 00001000 INTL 20210930) <6>[ 0.005571] ACPI: SSDT 0x000000006FFE8000 002450 (v02 INTEL IgfxSsdt 00003000 INTL 20210930) <6>[ 0.005573] ACPI: SSDT 0x000000006FFE7000 0000A5 (v02 INTEL TseSsdt 00001000 INTL 20210930) <6>[ 0.005574] ACPI: SSDT 0x000000006FFDD000 009176 (v02 INTEL TcssSsdt 00001000 INTL 20210930) <6>[ 0.005575] ACPI: SSDT 0x000000006FFDC000 0000E0 (v02 INTEL IpuSsdt 00001000 INTL 20210930) <6>[ 0.005577] ACPI: SSDT 0x000000006FFB1000 004AC3 (v02 INTEL LnlMRvp1 00001000 INTL 20210930) <6>[ 0.005578] ACPI: SSDT 0x000000006FFAF000 00140F (v02 INTEL I2Pm_Rvp 00001000 INTL 20210930) <6>[ 0.005579] ACPI: SSDT 0x000000006FFAB000 003956 (v02 INTEL Ther_Rvp 00001000 INTL 20210930) <6>[ 0.005581] ACPI: HPET 0x000000006FFA9000 000038 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005582] ACPI: WSMT 0x000000006FFFD000 000028 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005583] ACPI: APIC 0x000000006FFA7000 0000D8 (v06 INTEL LNL 00000000 01000013) <6>[ 0.005585] ACPI: MCFG 0x000000006FFA6000 00003C (v01 INTEL LNL 00000002 01000013) <6>[ 0.005586] ACPI: SSDT 0x000000006FFA5000 0006E3 (v02 INTEL PepoSsdt 00001000 INTL 20210930) <6>[ 0.005587] ACPI: SSDT 0x000000006FF9F000 005321 (v02 DptfTb DptfTabl 00001000 INTL 20210930) <6>[ 0.005588] ACPI: SSDT 0x000000006FF94000 00A46A (v02 MiCaTb MiCaTabl 00001000 INTL 20210930) <6>[ 0.005590] ACPI: SSDT 0x000000006FF86000 00D816 (v02 INTEL Cnv_Ssdt 00001000 INTL 20210930) <6>[ 0.005591] ACPI: LPIT 0x000000006FF85000 0000CC (v01 INTEL LNL 00000002 01000013) <6>[ 0.005592] ACPI: SSDT 0x000000006FF84000 000D5C (v02 INTEL PtidDevc 00001000 INTL 20210930) <6>[ 0.005594] ACPI: SSDT 0x000000006FF83000 0001F0 (v02 INTEL TbtTypeC 00000000 INTL 20210930) <6>[ 0.005595] ACPI: DBGP 0x000000006FF82000 000034 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005596] ACPI: DBG2 0x000000006FF81000 000054 (v00 INTEL LNL 00000002 01000013) <6>[ 0.005597] ACPI: NHLT 0x000000006FF80000 0002E3 (v00 INTEL LNL 00000002 01000013) <6>[ 0.005599] ACPI: SSDT 0x000000006FF7E000 00115C (v02 INTEL UsbCTabl 00001000 INTL 20210930) <6>[ 0.005600] ACPI: SSDT 0x000000006FF77000 00653B (v02 INTEL EcSsdt 00000000 INTL 20210930) <6>[ 0.005601] ACPI: ECDT 0x000000006FF76000 000069 (v01 LNL 00000002 01000013) <6>[ 0.005603] ACPI: DMAR 0x000000006FF75000 0000D8 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005605] ACPI: FPDT 0x000000006FF74000 000044 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005606] ACPI: SSDT 0x000000006FF73000 00086D (v02 INTEL xh_lnl_m 00000000 INTL 20210930) <6>[ 0.005607] ACPI: SSDT 0x000000006FF71000 0013DB (v02 SocGpe SocGpe 00003000 INTL 20210930) <6>[ 0.005609] ACPI: SSDT 0x000000006FF6D000 002463 (v02 SocCmn SocCmn 00003000 INTL 20210930) <6>[ 0.005610] ACPI: SDEV 0x000000006FFA8000 000046 (v01 00000000 00000000) <6>[ 0.005612] ACPI: SSDT 0x000000006FF62000 00A4FA (v02 INTEL St09Ssdt 00001000 INTL 20210930) <6>[ 0.005613] ACPI: PHAT 0x000000006FF61000 0007C0 (v01 INTEL LNL 00000005 MSFT 0100000D) <6>[ 0.005614] ACPI: BGRT 0x000000006FF60000 000038 (v01 INTEL LNL 00000002 01000013) <6>[ 0.005615] ACPI: Reserving FACP table memory at [mem 0x6ffaa000-0x6ffaa113] <6>[ 0.005616] ACPI: Reserving DSDT table memory at [mem 0x6ffb6000-0x6ffdb55e] <6>[ 0.005617] ACPI: Reserving FACS table memory at [mem 0x6fef1000-0x6fef103f] <6>[ 0.005617] ACPI: Reserving SSDT table memory at [mem 0x6fffc000-0x6fffc387] <6>[ 0.005618] ACPI: Reserving SSDT table memory at [mem 0x6fffb000-0x6fffb6a9] <6>[ 0.005618] ACPI: Reserving SSDT table memory at [mem 0x6fffa000-0x6fffa5fa] <6>[ 0.005618] ACPI: Reserving SSDT table memory at [mem 0x6fff9000-0x6fff91aa] <6>[ 0.005618] ACPI: Reserving SSDT table memory at [mem 0x6fff8000-0x6fff8393] <6>[ 0.005619] ACPI: Reserving SSDT table memory at [mem 0x6fff6000-0x6fff7bae] <6>[ 0.005619] ACPI: Reserving SSDT table memory at [mem 0x6fff4000-0x6fff561f] <6>[ 0.005619] ACPI: Reserving SSDT table memory at [mem 0x6fff2000-0x6fff3348] <6>[ 0.005619] ACPI: Reserving SSDT table memory at [mem 0x6fff1000-0x6fff1fba] <6>[ 0.005620] ACPI: Reserving SSDT table memory at [mem 0x6ffed000-0x6fff0bd6] <6>[ 0.005620] ACPI: Reserving DTPR table memory at [mem 0x6ffec000-0x6ffec08f] <6>[ 0.005620] ACPI: Reserving SSDT table memory at [mem 0x6ffeb000-0x6ffebfe1] <6>[ 0.005621] ACPI: Reserving SSDT table memory at [mem 0x6ffe8000-0x6ffea44f] <6>[ 0.005621] ACPI: Reserving SSDT table memory at [mem 0x6ffe7000-0x6ffe70a4] <6>[ 0.005621] ACPI: Reserving SSDT table memory at [mem 0x6ffdd000-0x6ffe6175] <6>[ 0.005621] ACPI: Reserving SSDT table memory at [mem 0x6ffdc000-0x6ffdc0df] <6>[ 0.005622] ACPI: Reserving SSDT table memory at [mem 0x6ffb1000-0x6ffb5ac2] <6>[ 0.005622] ACPI: Reserving SSDT table memory at [mem 0x6ffaf000-0x6ffb040e] <6>[ 0.005622] ACPI: Reserving SSDT table memory at [mem 0x6ffab000-0x6ffae955] <6>[ 0.005623] ACPI: Reserving HPET table memory at [mem 0x6ffa9000-0x6ffa9037] <6>[ 0.005623] ACPI: Reserving WSMT table memory at [mem 0x6fffd000-0x6fffd027] <6>[ 0.005623] ACPI: Reserving APIC table memory at [mem 0x6ffa7000-0x6ffa70d7] <6>[ 0.005623] ACPI: Reserving MCFG table memory at [mem 0x6ffa6000-0x6ffa603b] <6>[ 0.005624] ACPI: Reserving SSDT table memory at [mem 0x6ffa5000-0x6ffa56e2] <6>[ 0.005624] ACPI: Reserving SSDT table memory at [mem 0x6ff9f000-0x6ffa4320] <6>[ 0.005624] ACPI: Reserving SSDT table memory at [mem 0x6ff94000-0x6ff9e469] <6>[ 0.005625] ACPI: Reserving SSDT table memory at [mem 0x6ff86000-0x6ff93815] <6>[ 0.005625] ACPI: Reserving LPIT table memory at [mem 0x6ff85000-0x6ff850cb] <6>[ 0.005625] ACPI: Reserving SSDT table memory at [mem 0x6ff84000-0x6ff84d5b] <6>[ 0.005625] ACPI: Reserving SSDT table memory at [mem 0x6ff83000-0x6ff831ef] <6>[ 0.005626] ACPI: Reserving DBGP table memory at [mem 0x6ff82000-0x6ff82033] <6>[ 0.005626] ACPI: Reserving DBG2 table memory at [mem 0x6ff81000-0x6ff81053] <6>[ 0.005626] ACPI: Reserving NHLT table memory at [mem 0x6ff80000-0x6ff802e2] <6>[ 0.005627] ACPI: Reserving SSDT table memory at [mem 0x6ff7e000-0x6ff7f15b] <6>[ 0.005627] ACPI: Reserving SSDT table memory at [mem 0x6ff77000-0x6ff7d53a] <6>[ 0.005627] ACPI: Reserving ECDT table memory at [mem 0x6ff76000-0x6ff76068] <6>[ 0.005628] ACPI: Reserving DMAR table memory at [mem 0x6ff75000-0x6ff750d7] <6>[ 0.005628] ACPI: Reserving FPDT table memory at [mem 0x6ff74000-0x6ff74043] <6>[ 0.005628] ACPI: Reserving SSDT table memory at [mem 0x6ff73000-0x6ff7386c] <6>[ 0.005628] ACPI: Reserving SSDT table memory at [mem 0x6ff71000-0x6ff723da] <6>[ 0.005629] ACPI: Reserving SSDT table memory at [mem 0x6ff6d000-0x6ff6f462] <6>[ 0.005629] ACPI: Reserving SDEV table memory at [mem 0x6ffa8000-0x6ffa8045] <6>[ 0.005629] ACPI: Reserving SSDT table memory at [mem 0x6ff62000-0x6ff6c4f9] <6>[ 0.005630] ACPI: Reserving PHAT table memory at [mem 0x6ff61000-0x6ff617bf] <6>[ 0.005630] ACPI: Reserving BGRT table memory at [mem 0x6ff60000-0x6ff60037] <6>[ 0.005702] APIC: Switched APIC routing to: cluster x2apic <6>[ 0.005902] No NUMA configuration found <6>[ 0.005902] Faking a node at [mem 0x0000000000000000-0x000000087f7fffff] <6>[ 0.005907] NODE_DATA(0) allocated [mem 0x87f352e40-0x87f37dfff] <6>[ 0.006021] Zone ranges: <6>[ 0.006021] DMA [mem 0x0000000000001000-0x0000000000ffffff] <6>[ 0.006022] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] <6>[ 0.006023] Normal [mem 0x0000000100000000-0x000000087f7fffff] <6>[ 0.006024] Device empty <6>[ 0.006024] Movable zone start for each node <6>[ 0.006025] Early memory node ranges <6>[ 0.006025] node 0: [mem 0x0000000000001000-0x000000000009efff] <6>[ 0.006026] node 0: [mem 0x0000000000100000-0x000000006cac0fff] <6>[ 0.006027] node 0: [mem 0x000000006ffff000-0x000000006fffffff] <6>[ 0.006027] node 0: [mem 0x0000000104500000-0x000000087f7fffff] <6>[ 0.006028] Initmem setup node 0 [mem 0x0000000000001000-0x000000087f7fffff] <6>[ 0.006033] On node 0, zone DMA: 1 pages in unavailable ranges <6>[ 0.006047] On node 0, zone DMA: 97 pages in unavailable ranges <6>[ 0.007615] On node 0, zone DMA32: 13630 pages in unavailable ranges <6>[ 0.035406] On node 0, zone Normal: 17664 pages in unavailable ranges <6>[ 0.035413] On node 0, zone Normal: 2048 pages in unavailable ranges <6>[ 0.035897] ACPI: PM-Timer IO Port: 0x1808 <6>[ 0.035904] ACPI: X2APIC_NMI (uid[0xffffffff] high level lint[0x1]) <6>[ 0.035955] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-119 <6>[ 0.035957] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) <6>[ 0.035958] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) <6>[ 0.035960] ACPI: Using ACPI (MADT) for SMP configuration information <6>[ 0.035961] ACPI: HPET id: 0x8086a701 base: 0xfed00000 <7>[ 0.035973] e820: update [mem 0x6992d000-0x69947fff] usable ==> reserved <6>[ 0.035979] TSC deadline timer available <6>[ 0.035981] CPU topo: Max. logical packages: 1 <6>[ 0.035981] CPU topo: Max. logical dies: 1 <6>[ 0.035982] CPU topo: Max. dies per package: 1 <6>[ 0.035983] CPU topo: Max. threads per core: 1 <6>[ 0.035984] CPU topo: Num. cores per package: 8 <6>[ 0.035984] CPU topo: Num. threads per package: 8 <6>[ 0.035984] CPU topo: Allowing 8 present CPUs plus 0 hotplug CPUs <6>[ 0.035997] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff] <6>[ 0.035998] PM: hibernation: Registered nosave memory: [mem 0x0009f000-0x000fffff] <6>[ 0.035999] PM: hibernation: Registered nosave memory: [mem 0x68ff8000-0x68ff8fff] <6>[ 0.036000] PM: hibernation: Registered nosave memory: [mem 0x6992d000-0x69947fff] <6>[ 0.036000] PM: hibernation: Registered nosave memory: [mem 0x6cac1000-0x6fffefff] <6>[ 0.036001] PM: hibernation: Registered nosave memory: [mem 0x70000000-0x1044fffff] <6>[ 0.036003] [mem 0x80800000-0xfed1ffff] available for PCI devices <6>[ 0.036003] Booting paravirtualized kernel on bare hardware <6>[ 0.036005] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns <6>[ 0.036014] setup_percpu: NR_CPUS:8192 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1 <6>[ 0.036339] percpu: Embedded 86 pages/cpu s229376 r8192 d114688 u524288 <7>[ 0.036343] pcpu-alloc: s229376 r8192 d114688 u524288 alloc=1*2097152 <7>[ 0.036345] pcpu-alloc: [0] 0 1 2 3 [0] 4 5 6 7 <5>[ 0.036358] Kernel command line: BOOT_IMAGE=/boot/drm_intel root=/dev/nvme0n1p2 rootwait fsck.repair=yes nmi_watchdog=panic,auto panic=5 softdog.soft_panic=5 log_buf_len=1M trace_clock=global snd_hda_intel.probe_mask=0x104 xe.force_probe=* i915.force_probe=* drm.debug=0xe modprobe.blacklist=xe,i915,ast initcall_blacklist=simpledrm_platform_driver_init ro <7>[ 0.036446] blacklisting initcall simpledrm_platform_driver_init <5>[ 0.036463] random: crng init done <6>[ 0.038305] Dentry cache hash table entries: 4194304 (order: 13, 33554432 bytes, linear) <6>[ 0.039212] Inode-cache hash table entries: 2097152 (order: 12, 16777216 bytes, linear) <6>[ 0.039272] software IO TLB: area num 8. <6>[ 0.046648] Fallback order for Node 0: 0 <6>[ 0.046651] Built 1 zonelists, mobility grouping on. Total pages: 8289632 <6>[ 0.046652] Policy zone: Normal <6>[ 0.046661] mem auto-init: stack:off, heap alloc:on, heap free:off <6>[ 0.046661] stackdepot: allocating hash table via alloc_large_system_hash <6>[ 0.046664] stackdepot hash table entries: 1048576 (order: 12, 16777216 bytes, linear) <6>[ 0.047603] stackdepot: allocating space for 8192 stack pools via memblock <4>[ 0.079310] ********************************************************** <4>[ 0.079312] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.079312] ** ** <4>[ 0.079312] ** This system shows unhashed kernel memory addresses ** <4>[ 0.079313] ** via the console, logs, and other interfaces. This ** <4>[ 0.079313] ** might reduce the security of your system. ** <4>[ 0.079313] ** ** <4>[ 0.079313] ** If you see this message and you are not debugging ** <4>[ 0.079313] ** the kernel, report this immediately to your system ** <4>[ 0.079314] ** administrator! ** <4>[ 0.079314] ** ** <4>[ 0.079314] ** Use hash_pointers=always to force this mode off ** <4>[ 0.079314] ** ** <4>[ 0.079314] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** <4>[ 0.079314] ********************************************************** <6>[ 0.080402] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1 <6>[ 0.088629] ftrace: allocating 60601 entries in 240 pages <6>[ 0.088631] ftrace: allocated 240 pages with 4 groups <6>[ 0.090059] Dynamic Preempt: voluntary <6>[ 0.090588] Running RCU self tests <6>[ 0.090588] Running RCU synchronous self tests <6>[ 0.090588] rcu: Preemptible hierarchical RCU implementation. <6>[ 0.090589] rcu: RCU lockdep checking is enabled. <6>[ 0.090589] rcu: RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=8. <6>[ 0.090590] Trampoline variant of Tasks RCU enabled. <6>[ 0.090590] Rude variant of Tasks RCU enabled. <6>[ 0.090590] Tracing variant of Tasks RCU enabled. <6>[ 0.090591] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies. <6>[ 0.090591] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8 <6>[ 0.090657] Running RCU synchronous self tests <6>[ 0.090660] RCU Tasks: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8. <6>[ 0.090664] RCU Tasks Rude: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8. <6>[ 0.090666] RCU Tasks Trace: Setting shift to 3 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=8. <6>[ 0.101035] NR_IRQS: 524544, nr_irqs: 2048, preallocated irqs: 16 <6>[ 0.101512] rcu: srcu_init: Setting srcu_struct sizes based on contention. <6>[ 0.101927] Console: colour dummy device 80x25 <6>[ 0.101936] printk: legacy console [tty0] enabled <6>[ 0.103088] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar <6>[ 0.103095] ... MAX_LOCKDEP_SUBCLASSES: 8 <6>[ 0.103099] ... MAX_LOCK_DEPTH: 48 <6>[ 0.103102] ... MAX_LOCKDEP_KEYS: 8192 <6>[ 0.103106] ... CLASSHASH_SIZE: 4096 <6>[ 0.103109] ... MAX_LOCKDEP_ENTRIES: 524288 <6>[ 0.103113] ... MAX_LOCKDEP_CHAINS: 524288 <6>[ 0.103117] ... CHAINHASH_SIZE: 262144 <6>[ 0.103120] memory used by lock dependency info: 54145 kB <6>[ 0.103125] memory used for stack traces: 4224 kB <6>[ 0.103128] per task-struct memory footprint: 1920 bytes <6>[ 0.103180] ACPI: Core revision 20250807 <6>[ 0.104033] hpet: HPET dysfunctional in PC10. Force disabled. <6>[ 0.104096] APIC: Switch to symmetric I/O mode setup <6>[ 0.104101] DMAR: Host address width 38 <6>[ 0.104105] DMAR: DRHD base: 0x000000fc800000 flags: 0x0 <6>[ 0.104137] DMAR: dmar0: reg_base_addr fc800000 ver 7:1 cap e9de008cee690402 ecap 1aca9a00f0ef5e <6>[ 0.104168] DMAR: DRHD base: 0x000000fc810000 flags: 0x0 <6>[ 0.104187] DMAR: dmar1: reg_base_addr fc810000 ver 7:1 cap e9de008cee690402 ecap 1aca9a00f0ef5e <6>[ 0.104213] DMAR: DRHD base: 0x000000fc820000 flags: 0x1 <6>[ 0.104234] DMAR: dmar2: reg_base_addr fc820000 ver 7:1 cap e9de008cee690402 ecap 1ac89800f0efda <6>[ 0.104269] DMAR: SATC flags: 0x1 <6>[ 0.104279] DMAR-IR: IOAPIC id 2 under DRHD base 0xfc820000 IOMMU 2 <6>[ 0.104284] DMAR-IR: HPET id 0 under DRHD base 0xfc820000 <6>[ 0.104289] DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping. <6>[ 0.106344] DMAR-IR: Enabled IRQ remapping in x2apic mode <6>[ 0.111494] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x2cd5a8bb032, max_idle_ns: 440795365915 ns <6>[ 0.111513] Calibrating delay loop (skipped), value calculated using timer frequency.. 6220.80 BogoMIPS (lpj=3110400) <6>[ 0.111587] CPU0: Thermal monitoring enabled (TM1) <6>[ 0.111593] x86/cpu: User Mode Instruction Prevention (UMIP) activated <6>[ 0.111776] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 <6>[ 0.111781] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 <6>[ 0.111793] mitigations: Enabled attack vectors: user_kernel, user_user, guest_host, guest_guest, SMT mitigations: auto <6>[ 0.111805] Speculative Store Bypass: Mitigation: Speculative Store Bypass disabled via prctl <6>[ 0.111812] Spectre V2 : Mitigation: Enhanced / Automatic IBRS <6>[ 0.111817] VMSCAPE: Mitigation: IBPB before exit to userspace <6>[ 0.111821] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization <6>[ 0.111829] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier <6>[ 0.111845] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers' <6>[ 0.111851] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers' <6>[ 0.111857] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers' <6>[ 0.111862] x86/fpu: Supporting XSAVE feature 0x200: 'Protection Keys User registers' <6>[ 0.111869] x86/fpu: Supporting XSAVE feature 0x800: 'Control-flow User registers' <6>[ 0.111875] x86/fpu: Supporting XSAVE feature 0x1000: 'Control-flow Kernel registers (KVM only)' <6>[ 0.111883] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256 <6>[ 0.111888] x86/fpu: xstate_offset[9]: 832, xstate_sizes[9]: 8 <6>[ 0.111893] x86/fpu: xstate_offset[11]: 840, xstate_sizes[11]: 16 <6>[ 0.111898] x86/fpu: xstate_offset[12]: 856, xstate_sizes[12]: 24 <6>[ 0.111903] x86/fpu: Enabled xstate features 0x1a07, context size is 880 bytes, using 'compacted' format. <6>[ 0.112507] Freeing SMP alternatives memory: 56K <6>[ 0.112507] pid_max: default: 32768 minimum: 301 <6>[ 0.112507] LSM: initializing lsm=capability,landlock,yama,apparmor,ima,evm <6>[ 0.112507] landlock: Up and running. <6>[ 0.112507] Yama: becoming mindful. <6>[ 0.112507] AppArmor: AppArmor initialized <6>[ 0.112507] Mount-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.112507] Mountpoint-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) <6>[ 0.112507] Running RCU synchronous self tests <6>[ 0.112507] Running RCU synchronous self tests <6>[ 0.112507] smpboot: CPU0: Intel(R) Core(TM) Ultra 5 238V (family: 0x6, model: 0xbd, stepping: 0x1) <6>[ 0.112507] Performance Events: XSAVE Architectural LBR, PEBS fmt6+-baseline, AnyThread deprecated, Lunarlake Hybrid events, 32-deep LBR, full-width counters, Intel PMU driver. <6>[ 0.112507] core: cpu_core PMU driver: <6>[ 0.112507] ... version: 6 <6>[ 0.112507] ... bit width: 48 <6>[ 0.112507] ... generic counters: 10 <6>[ 0.112507] ... generic bitmap: 00000000000003ff <6>[ 0.112507] ... fixed-purpose counters: 4 <6>[ 0.112507] ... fixed-purpose bitmap: 000000000000000f <6>[ 0.112507] ... value mask: 0000ffffffffffff <6>[ 0.112507] ... max period: 00007fffffffffff <6>[ 0.112512] ... global_ctrl mask: 0001000f000003ff <6>[ 0.112589] signal: max sigframe size: 3632 <6>[ 0.112613] Estimated ratio of average max frequency by base frequency (times 1024): 1189 <6>[ 0.112713] rcu: Hierarchical SRCU implementation. <6>[ 0.112717] rcu: Max phase no-delay instances is 400. <6>[ 0.112859] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level <6>[ 0.114694] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter. <6>[ 0.114961] smp: Bringing up secondary CPUs ... <6>[ 0.115312] smpboot: x86: Booting SMP configuration: <6>[ 0.115318] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7 <6>[ 0.010810] core: cpu_atom PMU driver: <6>[ 0.010810] ... version: 6 <6>[ 0.010810] ... bit width: 48 <6>[ 0.010810] ... generic counters: 8 <6>[ 0.010810] ... generic bitmap: 00000000000000ff <6>[ 0.010810] ... fixed-purpose counters: 6 <6>[ 0.010810] ... fixed-purpose bitmap: 0000000000000077 <6>[ 0.010810] ... value mask: 0000ffffffffffff <6>[ 0.010810] ... max period: 00007fffffffffff <6>[ 0.010810] ... global_ctrl mask: 00000077000000ff <6>[ 0.121584] smp: Brought up 1 node, 8 CPUs <6>[ 0.121885] smpboot: Total of 8 processors activated (49766.40 BogoMIPS) <6>[ 0.123665] Memory: 32357980K/33158528K available (25417K kernel code, 5651K rwdata, 9540K rodata, 5704K init, 68232K bss, 777192K reserved, 0K cma-reserved) <6>[ 0.124121] devtmpfs: initialized <6>[ 0.124740] x86/mm: Memory block size: 128MB <6>[ 0.146554] ACPI: PM: Registering ACPI NVS region [mem 0x6fe68000-0x6ff4ffff] (950272 bytes) <6>[ 0.147078] Running RCU synchronous self tests <6>[ 0.147091] Running RCU synchronous self tests <6>[ 0.148537] Running RCU Tasks wait API self tests <6>[ 0.148635] Running RCU Tasks Rude wait API self tests <6>[ 0.148635] Running RCU Tasks Trace wait API self tests <6>[ 0.161573] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns <6>[ 0.161813] posixtimers hash table entries: 4096 (order: 6, 294912 bytes, linear) <6>[ 0.161885] futex hash table entries: 2048 (262144 bytes on 1 NUMA nodes, total 256 KiB, linear). <6>[ 0.162571] pinctrl core: initialized pinctrl subsystem <6>[ 0.163260] PM: RTC time: 05:19:35, date: 2025-11-09 <6>[ 0.164033] NET: Registered PF_NETLINK/PF_ROUTE protocol family <6>[ 0.165009] DMA: preallocated 4096 KiB GFP_KERNEL pool for atomic allocations <6>[ 0.165306] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations <6>[ 0.165588] DMA: preallocated 4096 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations <6>[ 0.165647] audit: initializing netlink subsys (disabled) <5>[ 0.165777] audit: type=2000 audit(1762665575.054:1): state=initialized audit_enabled=0 res=1 <6>[ 0.166791] thermal_sys: Registered thermal governor 'fair_share' <6>[ 0.166793] thermal_sys: Registered thermal governor 'bang_bang' <6>[ 0.166799] thermal_sys: Registered thermal governor 'step_wise' <6>[ 0.166804] thermal_sys: Registered thermal governor 'user_space' <6>[ 0.166809] thermal_sys: Registered thermal governor 'power_allocator' <6>[ 0.166848] cpuidle: using governor ladder <6>[ 0.166848] cpuidle: using governor menu <6>[ 0.166848] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5 <6>[ 0.167648] PCI: ECAM [mem 0xc0000000-0xcfffffff] (base 0xc0000000) for domain 0000 [bus 00-ff] <6>[ 0.167675] PCI: Using configuration type 1 for base access <6>[ 0.167799] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible. <6>[ 0.169581] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages <6>[ 0.169581] HugeTLB: 16380 KiB vmemmap can be freed for a 1.00 GiB page <6>[ 0.169581] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages <6>[ 0.169581] HugeTLB: 28 KiB vmemmap can be freed for a 2.00 MiB page <6>[ 0.173943] raid6: skipped pq benchmark and selected avx2x4 <6>[ 0.173950] raid6: using avx2x2 recovery algorithm <6>[ 0.174460] fbcon: Taking over console <6>[ 0.174588] ACPI: Added _OSI(Module Device) <6>[ 0.174593] ACPI: Added _OSI(Processor Device) <6>[ 0.174597] ACPI: Added _OSI(Processor Aggregator Device) <6>[ 0.180542] Callback from call_rcu_tasks_trace() invoked. <6>[ 0.670707] ACPI: 31 ACPI AML tables successfully acquired and loaded <6>[ 0.702383] ACPI: EC: EC started <6>[ 0.702396] ACPI: EC: interrupt blocked <6>[ 0.704777] ACPI: EC: EC_CMD/EC_SC=0x66, EC_DATA=0x62 <6>[ 0.704783] ACPI: EC: Boot ECDT EC used to handle transactions <6>[ 0.789739] Callback from call_rcu_tasks() invoked. <6>[ 1.015164] ACPI: USB4 _OSC: OS supports USB3+ DisplayPort+ PCIe+ XDomain+ <6>[ 1.015178] ACPI: USB4 _OSC: OS controls USB3+ DisplayPort+ PCIe+ XDomain+ <6>[ 1.045073] ACPI: Interpreter enabled <6>[ 1.046194] ACPI: PM: (supports S0 S4 S5) <6>[ 1.046258] ACPI: Using IOAPIC for interrupt routing <6>[ 1.055128] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug <6>[ 1.055140] PCI: Ignoring E820 reservations for host bridge windows <6>[ 1.086808] ACPI: Enabled 10 GPEs in block 00 to 7F <6>[ 1.086879] ACPI: Enabled 13 GPEs in block 80 to DF <6>[ 1.147379] ACPI: \_SB_.PC00.XHCI.RHUB.HS06.BTRT: New power resource <6>[ 1.148196] ACPI: \_SB_.PC00.XHCI.RHUB.HS06.DBTR: New power resource <6>[ 1.156952] ACPI: \_SB_.PC00.PAUD: New power resource <6>[ 1.470140] ACPI: \_SB_.PC00.CNVW.WRST: New power resource <6>[ 1.505739] ACPI: \_SB_.PC00.RP02.PXP_: New power resource <6>[ 1.651761] ACPI: \_SB_.PC00.RP03.PXSX.WRST: New power resource <6>[ 1.653630] ACPI: \_SB_.PC00.RP04.PXP_: New power resource <6>[ 1.661848] ACPI: \_SB_.PC00.RP05.PXP_: New power resource <6>[ 1.672018] ACPI: \_SB_.PC00.TBT0: New power resource <6>[ 1.672285] ACPI: \_SB_.PC00.TBT1: New power resource <6>[ 1.672545] ACPI: \_SB_.PC00.D3C_: New power resource <6>[ 1.977289] ACPI: \_TZ_.FN00: New power resource <6>[ 1.977861] ACPI: \_TZ_.FN01: New power resource <6>[ 1.978396] ACPI: \_TZ_.FN02: New power resource <6>[ 1.980922] ACPI: \_TZ_.FN03: New power resource <6>[ 1.987448] ACPI: \_TZ_.FN04: New power resource <6>[ 1.994994] ACPI: \PIN_: New power resource <6>[ 2.004150] ACPI: PCI Root Bridge [PC00] (domain 0000 [bus 00-fe]) <6>[ 2.004188] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HPX-Type3] <6>[ 2.012853] acpi PNP0A08:00: _OSC: OS now controls [SHPCHotplug PME AER PCIeCapability LTR DPC] <6>[ 2.035256] PCI host bridge to bus 0000:00 <6>[ 2.035305] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] <6>[ 2.035317] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] <6>[ 2.035326] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window] <6>[ 2.035337] pci_bus 0000:00: root bus resource [mem 0x80800000-0xbfffffff window] <6>[ 2.035347] pci_bus 0000:00: root bus resource [mem 0x2000000000-0x3fbfffffff window] <6>[ 2.035360] pci_bus 0000:00: root bus resource [bus 00-fe] <6>[ 2.039307] pci 0000:00:00.0: [8086:6400] type 00 class 0x060000 conventional PCI endpoint <6>[ 2.039951] pci 0000:00:02.0: [8086:64a0] type 00 class 0x030000 PCIe Root Complex Integrated Endpoint <6>[ 2.040042] pci 0000:00:02.0: BAR 0 [mem 0x3814000000-0x3814ffffff 64bit pref] <6>[ 2.040051] pci 0000:00:02.0: BAR 2 [mem 0x2000000000-0x200fffffff 64bit pref] <6>[ 2.040060] pci 0000:00:02.0: ROM [mem 0xffe00000-0xffffffff pref] <6>[ 2.040106] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] <6>[ 2.041422] pci 0000:00:04.0: [8086:641d] type 00 class 0x118000 conventional PCI endpoint <6>[ 2.041452] pci 0000:00:04.0: BAR 0 [mem 0x3815300000-0x381531ffff 64bit] <6>[ 2.042830] pci 0000:00:05.0: [8086:645d] type 00 class 0x048000 PCIe Root Complex Integrated Endpoint <6>[ 2.042860] pci 0000:00:05.0: BAR 0 [mem 0x3812000000-0x3813ffffff 64bit] <6>[ 2.042867] pci 0000:00:05.0: BAR 4 [mem 0x3815373000-0x3815373fff 64bit] <6>[ 2.043754] pci 0000:00:07.0: [8086:a84e] type 01 class 0x060400 PCIe Root Port <6>[ 2.043796] pci 0000:00:07.0: PCI bridge to [bus 01-2a] <6>[ 2.043808] pci 0000:00:07.0: bridge window [mem 0x8e000000-0x93ffffff] <6>[ 2.043827] pci 0000:00:07.0: bridge window [mem 0x2010000000-0x280fffffff 64bit pref] <6>[ 2.043942] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold <6>[ 2.044015] pci 0000:00:07.0: PTM enabled (root), 4ns granularity <6>[ 2.048357] pci 0000:00:07.1: [8086:a84f] type 01 class 0x060400 PCIe Root Port <6>[ 2.048403] pci 0000:00:07.1: PCI bridge to [bus 2b-54] <6>[ 2.048415] pci 0000:00:07.1: bridge window [mem 0x88000000-0x8dffffff] <6>[ 2.048434] pci 0000:00:07.1: bridge window [mem 0x2810000000-0x300fffffff 64bit pref] <6>[ 2.048551] pci 0000:00:07.1: PME# supported from D0 D3hot D3cold <6>[ 2.048616] pci 0000:00:07.1: PTM enabled (root), 4ns granularity <6>[ 2.052886] pci 0000:00:07.2: [8086:a860] type 01 class 0x060400 PCIe Root Port <6>[ 2.052930] pci 0000:00:07.2: PCI bridge to [bus 55-7e] <6>[ 2.052942] pci 0000:00:07.2: bridge window [mem 0x82000000-0x87ffffff] <6>[ 2.052961] pci 0000:00:07.2: bridge window [mem 0x3010000000-0x380fffffff 64bit pref] <6>[ 2.053078] pci 0000:00:07.2: PME# supported from D0 D3hot D3cold <6>[ 2.053143] pci 0000:00:07.2: PTM enabled (root), 4ns granularity <6>[ 2.057499] pci 0000:00:0a.0: [8086:647d] type 00 class 0x118000 PCIe Root Complex Integrated Endpoint <6>[ 2.057537] pci 0000:00:0a.0: BAR 0 [mem 0x3815350000-0x381535ffff 64bit] <6>[ 2.057552] pci 0000:00:0a.0: enabling Extended Tags <6>[ 2.057794] pci 0000:00:0b.0: [8086:643e] type 00 class 0x120000 PCIe Root Complex Integrated Endpoint <6>[ 2.057823] pci 0000:00:0b.0: BAR 0 [mem 0x3810000000-0x3811ffffff 64bit] <6>[ 2.057831] pci 0000:00:0b.0: BAR 4 [mem 0x3815372000-0x3815372fff 64bit] <6>[ 2.058296] pci 0000:00:0d.0: [8086:a831] type 00 class 0x0c0330 conventional PCI endpoint <6>[ 2.058349] pci 0000:00:0d.0: BAR 0 [mem 0x3815340000-0x381534ffff 64bit] <6>[ 2.058420] pci 0000:00:0d.0: PME# supported from D3hot D3cold <6>[ 2.060355] pci 0000:00:0d.2: [8086:a833] type 00 class 0x0c0340 conventional PCI endpoint <6>[ 2.060407] pci 0000:00:0d.2: BAR 0 [mem 0x38152c0000-0x38152fffff 64bit] <6>[ 2.060416] pci 0000:00:0d.2: BAR 2 [mem 0x3815371000-0x3815371fff 64bit] <6>[ 2.060474] pci 0000:00:0d.2: supports D1 D2 <6>[ 2.060478] pci 0000:00:0d.2: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 2.061774] pci 0000:00:0d.3: [8086:a834] type 00 class 0x0c0340 conventional PCI endpoint <6>[ 2.061826] pci 0000:00:0d.3: BAR 0 [mem 0x3815280000-0x38152bffff 64bit] <6>[ 2.061834] pci 0000:00:0d.3: BAR 2 [mem 0x3815370000-0x3815370fff 64bit] <6>[ 2.061892] pci 0000:00:0d.3: supports D1 D2 <6>[ 2.061896] pci 0000:00:0d.3: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 2.063544] pci 0000:00:12.0: [8086:a845] type 00 class 0x070000 conventional PCI endpoint <6>[ 2.063602] pci 0000:00:12.0: BAR 0 [mem 0x3815330000-0x381533ffff 64bit] <6>[ 2.063673] pci 0000:00:12.0: PME# supported from D0 D3hot <6>[ 2.066170] pci 0000:00:13.0: [8086:a862] type 00 class 0x078000 conventional PCI endpoint <6>[ 2.066260] pci 0000:00:13.0: BAR 0 [mem 0x381536f000-0x381536ffff 64bit] <6>[ 2.066366] pci 0000:00:13.0: PME# supported from D3hot <6>[ 2.067200] pci 0000:00:14.0: [8086:a87d] type 00 class 0x0c0330 conventional PCI endpoint <6>[ 2.067253] pci 0000:00:14.0: BAR 0 [mem 0x3815320000-0x381532ffff 64bit] <6>[ 2.067322] pci 0000:00:14.0: PME# supported from D3hot D3cold <6>[ 2.069209] pci 0000:00:14.2: [8086:a87f] type 00 class 0x050000 conventional PCI endpoint <6>[ 2.069273] pci 0000:00:14.2: BAR 0 [mem 0x3815360000-0x3815367fff 64bit] <6>[ 2.069282] pci 0000:00:14.2: BAR 2 [mem 0x381536e000-0x381536efff 64bit] <6>[ 2.069599] pci 0000:00:15.0: [8086:a878] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.069710] pci 0000:00:15.0: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.083282] pci 0000:00:15.1: [8086:a879] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.083353] pci 0000:00:15.1: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.094466] pci 0000:00:15.2: [8086:a87a] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.094579] pci 0000:00:15.2: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.107440] pci 0000:00:15.3: [8086:a87b] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.107649] pci 0000:00:15.3: BAR 0 [mem 0x00000000-0x00000fff 64bit] <6>[ 2.120315] pci 0000:00:16.0: [8086:a870] type 00 class 0x078000 conventional PCI endpoint <6>[ 2.120464] pci 0000:00:16.0: BAR 0 [mem 0x3815369000-0x3815369fff 64bit] <6>[ 2.120625] pci 0000:00:16.0: PME# supported from D3hot <6>[ 2.125685] pci 0000:00:1c.0: [8086:a839] type 01 class 0x060400 PCIe Root Port <6>[ 2.125732] pci 0000:00:1c.0: PCI bridge to [bus 7f] <6>[ 2.125744] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff] <6>[ 2.125755] pci 0000:00:1c.0: bridge window [mem 0x94300000-0x943fffff] <6>[ 2.125913] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold <6>[ 2.126005] pci 0000:00:1c.0: PTM enabled (root), 4ns granularity <6>[ 2.131362] pci 0000:00:1c.4: [8086:a83c] type 01 class 0x060400 PCIe Root Port <6>[ 2.131468] pci 0000:00:1c.4: PCI bridge to [bus 80] <6>[ 2.131499] pci 0000:00:1c.4: bridge window [mem 0x94200000-0x942fffff] <6>[ 2.131959] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold <6>[ 2.132163] pci 0000:00:1c.4: PTM enabled (root), 4ns granularity <6>[ 2.137138] pci 0000:00:1f.0: [8086:a807] type 00 class 0x060100 conventional PCI endpoint <6>[ 2.138637] pci 0000:00:1f.3: [8086:a828] type 00 class 0x040100 conventional PCI endpoint <6>[ 2.138752] pci 0000:00:1f.3: BAR 0 [mem 0x3815200000-0x381527ffff 64bit] <6>[ 2.138767] pci 0000:00:1f.3: BAR 4 [mem 0x3815000000-0x38151fffff 64bit] <6>[ 2.138882] pci 0000:00:1f.3: PME# supported from D3hot D3cold <6>[ 2.139412] pci 0000:00:1f.4: [8086:a822] type 00 class 0x0c0500 conventional PCI endpoint <6>[ 2.139481] pci 0000:00:1f.4: BAR 0 [mem 0x3815368000-0x38153680ff 64bit] <6>[ 2.139494] pci 0000:00:1f.4: BAR 4 [io 0xefa0-0xefbf] <6>[ 2.141037] pci 0000:00:1f.5: [8086:a823] type 00 class 0x0c8000 conventional PCI endpoint <6>[ 2.141221] pci 0000:00:1f.5: BAR 0 [mem 0xfe010000-0xfe010fff] <6>[ 2.141652] pci 0000:00:07.0: PCI bridge to [bus 01-2a] <6>[ 2.141818] pci 0000:00:07.1: PCI bridge to [bus 2b-54] <6>[ 2.141990] pci 0000:00:07.2: PCI bridge to [bus 55-7e] <6>[ 2.142183] pci 0000:7f:00.0: [10ec:8161] type 00 class 0x020000 PCIe Endpoint <6>[ 2.142254] pci 0000:7f:00.0: BAR 0 [io 0x3000-0x30ff] <6>[ 2.142265] pci 0000:7f:00.0: BAR 2 [mem 0x94304000-0x94304fff 64bit] <6>[ 2.142274] pci 0000:7f:00.0: BAR 4 [mem 0x94300000-0x94303fff 64bit] <6>[ 2.142440] pci 0000:7f:00.0: supports D1 D2 <6>[ 2.142443] pci 0000:7f:00.0: PME# supported from D0 D1 D2 D3hot D3cold <6>[ 2.143068] pci 0000:00:1c.0: ASPM: current common clock configuration is inconsistent, reconfiguring <6>[ 2.145003] pci 0000:00:1c.0: PCI bridge to [bus 7f] <6>[ 2.147245] pci 0000:80:00.0: [15b7:5011] type 00 class 0x010802 PCIe Endpoint <6>[ 2.147826] pci 0000:80:00.0: BAR 0 [mem 0x94200000-0x94203fff 64bit] <6>[ 2.149878] pci 0000:00:1c.4: ASPM: current common clock configuration is inconsistent, reconfiguring <6>[ 2.149945] pci 0000:00:1c.4: PCI bridge to [bus 80] <6>[ 2.548180] ACPI: \_SB_.PEPD: Duplicate LPS0 _DSM functions (mask: 0x1) <6>[ 11.813562] Low-power S0 idle used by default for system suspend <6>[ 11.867320] ACPI: EC: interrupt unblocked <6>[ 11.867331] ACPI: EC: event unblocked <6>[ 11.867367] ACPI: EC: EC_CMD/EC_SC=0x66, EC_DATA=0x62 <6>[ 11.867373] ACPI: EC: GPE=0x6e <6>[ 11.867379] ACPI: \_SB_.PC00.LPCB.H_EC: Boot ECDT EC initialization complete <6>[ 11.867389] ACPI: \_SB_.PC00.LPCB.H_EC: EC: Used to handle transactions and events <6>[ 11.868016] iommu: Default domain type: Translated <6>[ 11.868016] iommu: DMA domain TLB invalidation policy: lazy mode <5>[ 11.875046] SCSI subsystem initialized <7>[ 11.875824] libata version 3.00 loaded. <6>[ 11.875954] ACPI: bus type USB registered <6>[ 11.876221] usbcore: registered new interface driver usbfs <6>[ 11.876351] usbcore: registered new interface driver hub <6>[ 11.876471] usbcore: registered new device driver usb <6>[ 11.876829] pps_core: LinuxPPS API ver. 1 registered <6>[ 11.876840] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <6>[ 11.876886] PTP clock support registered <6>[ 11.877786] EDAC MC: Ver: 3.0.0 <6>[ 11.879797] efivars: Registered efivars operations <6>[ 11.883176] NetLabel: Initializing <6>[ 11.883187] NetLabel: domain hash size = 128 <6>[ 11.883196] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO <6>[ 11.883341] NetLabel: unlabeled traffic allowed by default <6>[ 11.883376] mctp: management component transport protocol core <6>[ 11.883388] NET: Registered PF_MCTP protocol family <6>[ 11.883493] PCI: Using ACPI for IRQ routing <7>[ 11.935067] PCI: pci_cache_line_size set to 64 bytes <6>[ 11.935354] pci 0000:00:1f.5: BAR 0 [mem 0xfe010000-0xfe010fff]: can't claim; no compatible bridge window <7>[ 11.935503] e820: reserve RAM buffer [mem 0x0009f000-0x0009ffff] <7>[ 11.935520] e820: reserve RAM buffer [mem 0x68ff8000-0x6bffffff] <7>[ 11.935526] e820: reserve RAM buffer [mem 0x6992d000-0x6bffffff] <7>[ 11.935531] e820: reserve RAM buffer [mem 0x6cac1000-0x6fffffff] <7>[ 11.935537] e820: reserve RAM buffer [mem 0x87f800000-0x87fffffff] <6>[ 11.936573] pci 0000:00:02.0: vgaarb: setting as boot VGA device <6>[ 11.936598] pci 0000:00:02.0: vgaarb: bridge control possible <6>[ 11.936611] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none <6>[ 11.936645] vgaarb: loaded <7>[ 11.940262] Monitor-Mwait will be used to enter C-1 state <7>[ 11.940533] Monitor-Mwait will be used to enter C-2 state <7>[ 11.940582] Monitor-Mwait will be used to enter C-3 state <6>[ 11.950630] clocksource: Switched to clocksource tsc-early <5>[ 11.961575] VFS: Disk quotas dquot_6.6.0 <6>[ 11.961635] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) <6>[ 11.964644] AppArmor: AppArmor Filesystem Enabled <6>[ 11.965102] pnp: PnP ACPI init <6>[ 11.967290] system 00:00: [io 0x0680-0x069f] has been reserved <6>[ 11.967318] system 00:00: [io 0x164e-0x164f] has been reserved <6>[ 11.970833] system 00:02: [io 0x06a4] has been reserved <6>[ 11.970855] system 00:02: [io 0x06a0] has been reserved <6>[ 12.020237] system 00:03: [mem 0xfedc0000-0xfedc7fff] has been reserved <6>[ 12.020262] system 00:03: [mem 0xd8000000-0xd8000fff] has been reserved <6>[ 12.020282] system 00:03: [mem 0x00000000-0x00000fff] could not be reserved <6>[ 12.020296] system 00:03: [mem 0xc0000000-0xcfffffff] has been reserved <6>[ 12.020309] system 00:03: [mem 0xfed20000-0xfed7ffff] has been reserved <6>[ 12.020325] system 00:03: [mem 0xfc800000-0xfc81ffff] could not be reserved <6>[ 12.020340] system 00:03: [mem 0xfed45000-0xfed8ffff] could not be reserved <6>[ 12.020354] system 00:03: [mem 0xfee00000-0xfeefffff] has been reserved <6>[ 12.024779] system 00:04: [io 0x2000-0x20fe] has been reserved <6>[ 12.028687] system 00:06: [io 0x1854-0x1857] has been reserved <6>[ 12.028984] system 00:07: [mem 0x00000000-0x0009cfff] could not be reserved <6>[ 12.036335] pnp: PnP ACPI: found 8 devices <6>[ 12.059489] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns <6>[ 12.059939] NET: Registered PF_INET protocol family <6>[ 12.060186] IP idents hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 12.063165] tcp_listen_portaddr_hash hash table entries: 16384 (order: 8, 1179648 bytes, linear) <6>[ 12.063348] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) <6>[ 12.063533] TCP established hash table entries: 262144 (order: 9, 2097152 bytes, linear) <6>[ 12.064397] TCP bind hash table entries: 65536 (order: 11, 9437184 bytes, vmalloc hugepage) <6>[ 12.065496] TCP: Hash tables configured (established 262144 bind 65536) <6>[ 12.065931] UDP hash table entries: 16384 (order: 10, 4194304 bytes, linear) <6>[ 12.066595] UDP-Lite hash table entries: 16384 (order: 10, 4194304 bytes, linear) <6>[ 12.067240] NET: Registered PF_UNIX/PF_LOCAL protocol family <6>[ 12.067297] pci 0000:00:07.0: bridge window [io 0x1000-0x0fff] to [bus 01-2a] add_size 1000 <6>[ 12.067308] pci 0000:00:07.1: bridge window [io 0x1000-0x0fff] to [bus 2b-54] add_size 1000 <6>[ 12.067316] pci 0000:00:07.2: bridge window [io 0x1000-0x0fff] to [bus 55-7e] add_size 1000 <6>[ 12.067356] pci 0000:00:07.0: bridge window [io 0x4000-0x4fff]: assigned <6>[ 12.067361] pci 0000:00:07.1: bridge window [io 0x5000-0x5fff]: assigned <6>[ 12.067367] pci 0000:00:07.2: bridge window [io 0x6000-0x6fff]: assigned <6>[ 12.067372] pci 0000:00:15.0: BAR 0 [mem 0x381536a000-0x381536afff 64bit]: assigned <6>[ 12.067393] pci 0000:00:15.1: BAR 0 [mem 0x381536b000-0x381536bfff 64bit]: assigned <6>[ 12.067421] pci 0000:00:15.2: BAR 0 [mem 0x381536c000-0x381536cfff 64bit]: assigned <6>[ 12.067445] pci 0000:00:15.3: BAR 0 [mem 0x381536d000-0x381536dfff 64bit]: assigned <6>[ 12.067470] pci 0000:00:1f.5: BAR 0 [mem 0x80800000-0x80800fff]: assigned <6>[ 12.067503] pci 0000:00:07.0: PCI bridge to [bus 01-2a] <6>[ 12.067514] pci 0000:00:07.0: bridge window [io 0x4000-0x4fff] <6>[ 12.067523] pci 0000:00:07.0: bridge window [mem 0x8e000000-0x93ffffff] <6>[ 12.067531] pci 0000:00:07.0: bridge window [mem 0x2010000000-0x280fffffff 64bit pref] <6>[ 12.067543] pci 0000:00:07.1: PCI bridge to [bus 2b-54] <6>[ 12.067549] pci 0000:00:07.1: bridge window [io 0x5000-0x5fff] <6>[ 12.067558] pci 0000:00:07.1: bridge window [mem 0x88000000-0x8dffffff] <6>[ 12.067566] pci 0000:00:07.1: bridge window [mem 0x2810000000-0x300fffffff 64bit pref] <6>[ 12.067580] pci 0000:00:07.2: PCI bridge to [bus 55-7e] <6>[ 12.067586] pci 0000:00:07.2: bridge window [io 0x6000-0x6fff] <6>[ 12.067595] pci 0000:00:07.2: bridge window [mem 0x82000000-0x87ffffff] <6>[ 12.067603] pci 0000:00:07.2: bridge window [mem 0x3010000000-0x380fffffff 64bit pref] <6>[ 12.067615] pci 0000:00:1c.0: PCI bridge to [bus 7f] <6>[ 12.067621] pci 0000:00:1c.0: bridge window [io 0x3000-0x3fff] <6>[ 12.067629] pci 0000:00:1c.0: bridge window [mem 0x94300000-0x943fffff] <6>[ 12.067641] pci 0000:00:1c.4: PCI bridge to [bus 80] <6>[ 12.067677] pci 0000:00:1c.4: bridge window [mem 0x94200000-0x942fffff] <6>[ 12.067724] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] <6>[ 12.067728] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] <6>[ 12.067733] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window] <6>[ 12.067739] pci_bus 0000:00: resource 7 [mem 0x80800000-0xbfffffff window] <6>[ 12.067744] pci_bus 0000:00: resource 8 [mem 0x2000000000-0x3fbfffffff window] <6>[ 12.067749] pci_bus 0000:01: resource 0 [io 0x4000-0x4fff] <6>[ 12.067753] pci_bus 0000:01: resource 1 [mem 0x8e000000-0x93ffffff] <6>[ 12.067758] pci_bus 0000:01: resource 2 [mem 0x2010000000-0x280fffffff 64bit pref] <6>[ 12.067764] pci_bus 0000:2b: resource 0 [io 0x5000-0x5fff] <6>[ 12.067769] pci_bus 0000:2b: resource 1 [mem 0x88000000-0x8dffffff] <6>[ 12.067773] pci_bus 0000:2b: resource 2 [mem 0x2810000000-0x300fffffff 64bit pref] <6>[ 12.067779] pci_bus 0000:55: resource 0 [io 0x6000-0x6fff] <6>[ 12.067783] pci_bus 0000:55: resource 1 [mem 0x82000000-0x87ffffff] <6>[ 12.067788] pci_bus 0000:55: resource 2 [mem 0x3010000000-0x380fffffff 64bit pref] <6>[ 12.067794] pci_bus 0000:7f: resource 0 [io 0x3000-0x3fff] <6>[ 12.067798] pci_bus 0000:7f: resource 1 [mem 0x94300000-0x943fffff] <6>[ 12.067803] pci_bus 0000:80: resource 1 [mem 0x94200000-0x942fffff] <6>[ 12.068705] pci 0000:00:0d.0: enabling device (0000 -> 0002) <6>[ 12.070172] PCI: CLS 0 bytes, default 64 <6>[ 12.070271] DMAR: No RMRR found <6>[ 12.070305] DMAR: No ATSR found <6>[ 12.070308] DMAR: dmar1: Using Queued invalidation <6>[ 12.070314] DMAR: dmar0: Using Queued invalidation <6>[ 12.070319] DMAR: dmar2: Using Queued invalidation <6>[ 12.071407] pci 0000:00:04.0: Adding to iommu group 0 <6>[ 12.071490] pci 0000:00:05.0: Adding to iommu group 1 <6>[ 12.071553] pci 0000:00:0a.0: Adding to iommu group 2 <6>[ 12.071611] pci 0000:00:0b.0: Adding to iommu group 3 <6>[ 12.074858] pci 0000:00:02.0: Adding to iommu group 4 <6>[ 12.075942] pci 0000:00:00.0: Adding to iommu group 5 <6>[ 12.076012] pci 0000:00:07.0: Adding to iommu group 6 <6>[ 12.076078] pci 0000:00:07.1: Adding to iommu group 7 <6>[ 12.076139] pci 0000:00:07.2: Adding to iommu group 8 <6>[ 12.076223] pci 0000:00:0d.0: Adding to iommu group 9 <6>[ 12.076265] pci 0000:00:0d.2: Adding to iommu group 9 <6>[ 12.076305] pci 0000:00:0d.3: Adding to iommu group 9 <6>[ 12.076370] pci 0000:00:12.0: Adding to iommu group 10 <6>[ 12.076432] pci 0000:00:13.0: Adding to iommu group 11 <6>[ 12.076497] pci 0000:00:14.0: Adding to iommu group 12 <6>[ 12.076537] pci 0000:00:14.2: Adding to iommu group 12 <6>[ 12.076616] pci 0000:00:15.0: Adding to iommu group 13 <6>[ 12.076657] pci 0000:00:15.1: Adding to iommu group 13 <6>[ 12.076697] pci 0000:00:15.2: Adding to iommu group 13 <6>[ 12.076739] pci 0000:00:15.3: Adding to iommu group 13 <6>[ 12.076799] pci 0000:00:16.0: Adding to iommu group 14 <6>[ 12.076859] pci 0000:00:1c.0: Adding to iommu group 15 <6>[ 12.076936] pci 0000:00:1c.4: Adding to iommu group 16 <6>[ 12.077020] pci 0000:00:1f.0: Adding to iommu group 17 <6>[ 12.077061] pci 0000:00:1f.3: Adding to iommu group 17 <6>[ 12.077106] pci 0000:00:1f.4: Adding to iommu group 17 <6>[ 12.077149] pci 0000:00:1f.5: Adding to iommu group 17 <6>[ 12.077206] pci 0000:7f:00.0: Adding to iommu group 18 <6>[ 12.077289] pci 0000:80:00.0: Adding to iommu group 19 <6>[ 12.085237] DMAR: Intel(R) Virtualization Technology for Directed I/O <6>[ 12.085243] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) <6>[ 12.085248] software IO TLB: mapped [mem 0x0000000063ac2000-0x0000000067ac2000] (64MB) <6>[ 12.089872] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x2cd5a8bb032, max_idle_ns: 440795365915 ns <6>[ 12.090090] clocksource: Switched to clocksource tsc <6>[ 12.091025] platform rtc_cmos: registered platform RTC device (no PNP device found) <5>[ 12.095545] Initialise system trusted keyrings <5>[ 12.095593] Key type blacklist registered <6>[ 12.096196] workingset: timestamp_bits=36 max_order=23 bucket_order=0 <6>[ 12.103222] squashfs: version 4.0 (2009/01/31) Phillip Lougher <6>[ 12.103299] ntfs3: Enabled Linux POSIX ACLs support <6>[ 12.103303] ntfs3: Read-only LZX/Xpress compression included <5>[ 12.103759] integrity: Platform Keyring initialized <5>[ 12.103772] integrity: Machine keyring initialized <6>[ 12.107959] xor: automatically using best checksumming function avx <5>[ 12.107966] Key type asymmetric registered <5>[ 12.107973] Asymmetric key parser 'x509' registered <6>[ 12.108048] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242) <6>[ 12.108797] io scheduler mq-deadline registered <6>[ 12.109598] ledtrig-cpu: registered to indicate activity on CPUs <6>[ 12.110659] pcieport 0000:00:07.0: PME: Signaling with IRQ 126 <6>[ 12.111156] pcieport 0000:00:07.0: AER: enabled with IRQ 126 <6>[ 12.111993] pcieport 0000:00:07.1: PME: Signaling with IRQ 127 <6>[ 12.112473] pcieport 0000:00:07.1: AER: enabled with IRQ 127 <6>[ 12.113302] pcieport 0000:00:07.2: PME: Signaling with IRQ 128 <6>[ 12.113790] pcieport 0000:00:07.2: AER: enabled with IRQ 128 <6>[ 12.114536] pcieport 0000:00:1c.0: PME: Signaling with IRQ 129 <6>[ 12.115044] pcieport 0000:00:1c.0: AER: enabled with IRQ 129 <6>[ 12.116131] pcieport 0000:00:1c.4: PME: Signaling with IRQ 130 <6>[ 12.116681] pcieport 0000:00:1c.4: AER: enabled with IRQ 130 <6>[ 12.118014] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:16/PNP0C09:00/PNP0C0D:00/input/input0 <6>[ 12.118150] ACPI: button: Lid Switch [LID0] <6>[ 12.118328] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1 <6>[ 12.118458] ACPI: button: Sleep Button [SLPB] <6>[ 12.118612] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2 <6>[ 12.118802] ACPI: button: Power Button [PWRB] <6>[ 12.270913] thermal LNXTHERM:00: registered as thermal_zone0 <6>[ 12.270935] ACPI: thermal: Thermal Zone [TZ00] (65 C) <6>[ 12.274144] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled <6>[ 12.275144] ACPI: battery: Slot [BAT1] (battery absent) <6>[ 12.277830] ACPI: battery: Slot [BAT0] (battery present) <6>[ 12.299617] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A <6>[ 12.337909] serial 0000:00:12.0: enabling device (0000 -> 0002) <5>[ 12.343832] hpet_acpi_add: no address or irqs in _CRS <6>[ 12.344044] Linux agpgart interface v0.103 <6>[ 12.345217] ACPI: bus type drm_connector registered <7>[ 12.347032] initcall simpledrm_platform_driver_init blacklisted <6>[ 12.381685] loop: module loaded <6>[ 12.449747] intel-lpss 0000:00:15.0: enabling device (0000 -> 0002) <6>[ 12.692302] intel-lpss 0000:00:15.1: enabling device (0000 -> 0002) <6>[ 12.836657] intel-lpss 0000:00:15.2: enabling device (0000 -> 0002) <6>[ 12.949906] intel-lpss 0000:00:15.3: enabling device (0000 -> 0002) <5>[ 13.063267] Key type psk registered <6>[ 13.068433] nvme 0000:80:00.0: platform quirk: setting simple suspend <6>[ 13.069227] nvme nvme0: pci function 0000:80:00.0 <6>[ 13.069692] tun: Universal TUN/TAP device driver, 1.6 <6>[ 13.070686] xhci_hcd 0000:00:0d.0: xHCI Host Controller <6>[ 13.070786] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 1 <6>[ 13.072596] xhci_hcd 0000:00:0d.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 <6>[ 13.074541] xhci_hcd 0000:00:0d.0: xHCI Host Controller <6>[ 13.074568] xhci_hcd 0000:00:0d.0: new USB bus registered, assigned bus number 2 <6>[ 13.074587] xhci_hcd 0000:00:0d.0: Host supports USB 3.2 Enhanced SuperSpeed <6>[ 13.074964] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.18 <6>[ 13.074989] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 13.075000] usb usb1: Product: xHCI Host Controller <6>[ 13.075008] usb usb1: Manufacturer: Linux 6.18.0-rc4-lgci-xe-xe-pw-155951v4+ xhci-hcd <6>[ 13.075020] usb usb1: SerialNumber: 0000:00:0d.0 <6>[ 13.076263] hub 1-0:1.0: USB hub found <6>[ 13.076376] hub 1-0:1.0: 1 port detected <6>[ 13.080085] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.18 <6>[ 13.080100] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 13.080110] usb usb2: Product: xHCI Host Controller <6>[ 13.080118] usb usb2: Manufacturer: Linux 6.18.0-rc4-lgci-xe-xe-pw-155951v4+ xhci-hcd <6>[ 13.080129] usb usb2: SerialNumber: 0000:00:0d.0 <6>[ 13.080910] hub 2-0:1.0: USB hub found <6>[ 13.080955] hub 2-0:1.0: 3 ports detected <6>[ 13.104196] nvme nvme0: 8/0/0 default/read/poll queues <6>[ 13.105420] xhci_hcd 0000:00:14.0: xHCI Host Controller <6>[ 13.105478] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3 <6>[ 13.107259] xhci_hcd 0000:00:14.0: hcc params 0x20007fc1 hci version 0x120 quirks 0x0000000200009810 <6>[ 13.109190] xhci_hcd 0000:00:14.0: xHCI Host Controller <6>[ 13.109217] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4 <6>[ 13.109242] xhci_hcd 0000:00:14.0: Host supports USB 3.2 Enhanced SuperSpeed <6>[ 13.109477] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.18 <6>[ 13.109491] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 13.109502] usb usb3: Product: xHCI Host Controller <6>[ 13.109509] usb usb3: Manufacturer: Linux 6.18.0-rc4-lgci-xe-xe-pw-155951v4+ xhci-hcd <6>[ 13.109520] usb usb3: SerialNumber: 0000:00:14.0 <6>[ 13.110374] hub 3-0:1.0: USB hub found <6>[ 13.110443] hub 3-0:1.0: 8 ports detected <6>[ 13.112666] nvme0n1: p1 p2 <6>[ 13.140465] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.18 <6>[ 13.140487] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 <6>[ 13.140498] usb usb4: Product: xHCI Host Controller <6>[ 13.140505] usb usb4: Manufacturer: Linux 6.18.0-rc4-lgci-xe-xe-pw-155951v4+ xhci-hcd <6>[ 13.140516] usb usb4: SerialNumber: 0000:00:14.0 <6>[ 13.141657] hub 4-0:1.0: USB hub found <6>[ 13.141709] hub 4-0:1.0: 2 ports detected <6>[ 13.149077] usbcore: registered new interface driver usb-storage <6>[ 13.149292] usbcore: registered new interface driver usbserial_generic <6>[ 13.149393] usbserial: USB Serial support registered for generic <6>[ 13.149471] usbcore: registered new interface driver ftdi_sio <6>[ 13.149509] usbserial: USB Serial support registered for FTDI USB Serial Device <6>[ 13.149580] usbcore: registered new interface driver pl2303 <6>[ 13.149619] usbserial: USB Serial support registered for pl2303 <6>[ 13.149753] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 <4>[ 13.149764] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp <3>[ 13.861603] i8042: Can't read CTR while initializing i8042 <3>[ 13.861616] i8042 i8042: probe with driver i8042 failed with error -5 <6>[ 13.862134] mousedev: PS/2 mouse device common for all mice <6>[ 13.863416] rtc_cmos rtc_cmos: RTC can wake from S4 <6>[ 13.865382] rtc_cmos rtc_cmos: registered as rtc0 <6>[ 13.865605] rtc_cmos rtc_cmos: setting system clock to 2025-11-09T05:19:49 UTC (1762665589) <6>[ 13.865799] rtc_cmos rtc_cmos: alarms up to one month, y3k, 114 bytes nvram <6>[ 13.865857] i2c_dev: i2c /dev entries driver <6>[ 13.871128] softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=5 (nowayout=0) <6>[ 13.871143] softdog: soft_reboot_cmd= soft_active_on_boot=0 <4>[ 13.871155] device-mapper: core: CONFIG_IMA_DISABLE_HTABLE is disabled. Duplicate IMA measurements will not be recorded in the IMA log. <6>[ 13.871200] device-mapper: uevent: version 1.0.3 <6>[ 13.871565] device-mapper: ioctl: 4.50.0-ioctl (2025-04-28) initialised: dm-devel@lists.linux.dev <6>[ 13.871584] intel_pstate: Intel P-state driver initializing <6>[ 13.875648] Hybrid CPU capacity scaling enabled <6>[ 13.876031] processor cpu0: EM: created perf domain <6>[ 13.876287] processor cpu1: EM: created perf domain <6>[ 13.876531] processor cpu2: EM: created perf domain <6>[ 13.876775] processor cpu3: EM: created perf domain <6>[ 13.877034] processor cpu4: EM: created perf domain <6>[ 13.877293] processor cpu5: EM: created perf domain <6>[ 13.877546] processor cpu6: EM: created perf domain <6>[ 13.877795] processor cpu7: EM: created perf domain <6>[ 13.879638] intel_pstate: HWP enabled <6>[ 13.879652] sdhci: Secure Digital Host Controller Interface driver <6>[ 13.879661] sdhci: Copyright(c) Pierre Ossman <6>[ 13.879871] sdhci-pltfm: SDHCI platform and OF driver helper <6>[ 13.883444] Relocating firmware framebuffer to offset 0x0000000000800000[d] within [mem 0x2000000000-0x200fffffff flags 0x14220c] <6>[ 13.884639] drop_monitor: Initializing network drop monitor service <6>[ 13.884937] NET: Registered PF_INET6 protocol family <6>[ 13.886312] Segment Routing with IPv6 <6>[ 13.886362] In-situ OAM (IOAM) with IPv6 <6>[ 13.886421] NET: Registered PF_PACKET protocol family <5>[ 13.886610] Key type dns_resolver registered <4>[ 13.890681] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' <6>[ 13.891027] microcode: Current revision: 0x00000124 <6>[ 13.891598] IPI shorthand broadcast: enabled <6>[ 13.911798] sched_clock: Marking stable (13901001247, 9810064)->(13979525749, -68714438) <6>[ 13.912627] registered taskstats version 1 <5>[ 13.913788] Loading compiled-in X.509 certificates <6>[ 13.958453] Demotion targets for Node 0: null <6>[ 13.958744] kmemleak: Kernel memory leak detector initialized (mem pool available: 14946) <6>[ 13.958748] kmemleak: Automatic memory scanning thread started <5>[ 13.958979] Key type .fscrypt registered <5>[ 13.958984] Key type fscrypt-provisioning registered <6>[ 13.961897] Btrfs loaded, zoned=yes, fsverity=yes <5>[ 13.963961] Key type encrypted registered <6>[ 13.963971] AppArmor: AppArmor sha256 policy hashing enabled <6>[ 13.964188] ima: No TPM chip found, activating TPM-bypass! <5>[ 13.964212] Loading compiled-in module X.509 certificates <5>[ 13.964929] Loaded X.509 cert 'Build time autogenerated kernel key: 416155ccb6512e2b24149f9d8b1ff868499c144c' <6>[ 13.964940] ima: Allocated hash algorithm: sha256 <6>[ 13.964983] ima: No architecture policies found <6>[ 13.965068] evm: Initialising EVM extended attributes: <6>[ 13.965073] evm: security.selinux <6>[ 13.965076] evm: security.SMACK64 <6>[ 13.965079] evm: security.SMACK64EXEC <6>[ 13.965083] evm: security.SMACK64TRANSMUTE <6>[ 13.965086] evm: security.SMACK64MMAP <6>[ 13.965089] evm: security.apparmor <6>[ 13.965092] evm: security.ima <6>[ 13.965095] evm: security.capability <6>[ 13.965098] evm: HMAC attrs: 0x1 <6>[ 13.967036] PM: Magic number: 1:506:314 <6>[ 13.967222] netconsole: network logging started <6>[ 13.967786] RAS: Correctable Errors collector initialized. <6>[ 13.968246] clk: Disabling unused clocks <6>[ 13.968257] PM: genpd: Disabling unused power domains <4>[ 13.968686] check access for rdinit=/init failed: -2, ignoring <6>[ 13.968693] md: Waiting for all devices to be available before autodetect <6>[ 13.968698] md: If you don't use raid, use raid=noautodetect <6>[ 13.968703] md: Autodetecting RAID arrays. <6>[ 13.968711] md: autorun ... <6>[ 13.968713] md: ... autorun DONE. <6>[ 14.013112] EXT4-fs (nvme0n1p2): mounted filesystem 9a25468b-c3fd-45e2-b59f-4eab10a53c55 ro with ordered data mode. Quota mode: none. <6>[ 14.013177] VFS: Mounted root (ext4 filesystem) readonly on device 259:2. <6>[ 14.013661] devtmpfs: mounted <6>[ 14.030427] Freeing unused decrypted memory: 2036K <6>[ 14.031285] Freeing unused kernel image (initmem) memory: 5704K <6>[ 14.031310] Write protecting the kernel read-only data: 36864k <6>[ 14.031891] Freeing unused kernel image (text/rodata gap) memory: 1204K <6>[ 14.032102] Freeing unused kernel image (rodata/data gap) memory: 700K <6>[ 14.036746] x86/mm: Checked W+X mappings: passed, no W+X pages found. <6>[ 14.036773] Run /sbin/init as init process <7>[ 14.036777] with arguments: <7>[ 14.036778] /sbin/init <7>[ 14.036779] with environment: <7>[ 14.036779] HOME=/ <7>[ 14.036780] TERM=linux <7>[ 14.084964] systemd[1]: Inserted module 'autofs4' <7>[ 14.122098] systemd[1]: systemd 255.4-1ubuntu8.5 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) <7>[ 14.122178] systemd[1]: Detected architecture x86-64. <7>[ 14.124597] systemd[1]: Hostname set to . <7>[ 14.372825] systemd[1]: Queued start job for default target graphical.target. <7>[ 14.401438] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe. <7>[ 14.405628] systemd[1]: Created slice system-systemd\x2dfsck.slice - Slice /system/systemd-fsck. <7>[ 14.408778] systemd[1]: Created slice user.slice - User and Session Slice. <7>[ 14.409282] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch. <7>[ 14.410326] systemd[1]: Set up automount proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point. <7>[ 14.410498] systemd[1]: Expecting device dev-disk-by\x2duuid-BBA9\x2dCAA8.device - /dev/disk/by-uuid/BBA9-CAA8... <7>[ 14.410620] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes. <7>[ 14.410738] systemd[1]: Reached target slices.target - Slice Units. <7>[ 14.410843] systemd[1]: Reached target snapd.mounts-pre.target - Mounting snaps. <7>[ 14.410939] systemd[1]: Reached target snapd.mounts.target - Mounted snaps. <7>[ 14.411039] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes. <7>[ 14.411371] systemd[1]: Listening on dm-event.socket - Device-mapper event daemon FIFOs. <7>[ 14.411905] systemd[1]: Listening on lvm2-lvmpolld.socket - LVM2 poll daemon socket. <7>[ 14.412264] systemd[1]: Listening on multipathd.socket - multipathd control socket. <7>[ 14.412642] systemd[1]: Listening on syslog.socket - Syslog Socket. <7>[ 14.412940] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket. <7>[ 14.413164] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe. <7>[ 14.413477] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log). <7>[ 14.413808] systemd[1]: Listening on systemd-journald.socket - Journal Socket. <7>[ 14.414122] systemd[1]: Listening on systemd-networkd.socket - Network Service Netlink Socket. <7>[ 14.414292] systemd[1]: systemd-pcrextend.socket - TPM2 PCR Extension (Varlink) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). <7>[ 14.414574] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket. <7>[ 14.414830] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket. <7>[ 14.418139] systemd[1]: Mounting dev-hugepages.mount - Huge Pages File System... <7>[ 14.420741] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System... <7>[ 14.423587] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System... <7>[ 14.426794] systemd[1]: Mounting sys-kernel-tracing.mount - Kernel Trace File System... <7>[ 14.433794] systemd[1]: Starting systemd-journald.service - Journal Service... <7>[ 14.437330] systemd[1]: Starting keyboard-setup.service - Set the console keyboard layout... <7>[ 14.440742] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes... <7>[ 14.443929] systemd[1]: Starting lvm2-monitor.service - Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling... <7>[ 14.447506] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs... <7>[ 14.450560] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod... <7>[ 14.454417] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm... <7>[ 14.457870] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore... <7>[ 14.461797] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse... <7>[ 14.466094] systemd-journald[206]: Collecting audit messages is disabled. <7>[ 14.467211] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop... <7>[ 14.471763] systemd[1]: Starting modprobe@nvme_fabrics.service - Load Kernel Module nvme_fabrics... <7>[ 14.472055] systemd[1]: netplan-ovs-cleanup.service - OpenVSwitch configuration for cleanup was skipped because of an unmet condition check (ConditionFileIsExecutable=/usr/bin/ovs-vsctl). <7>[ 14.476747] systemd[1]: Starting systemd-fsck-root.service - File System Check on Root Device... <6>[ 14.478839] pstore: Using crash dump compression: deflate <6>[ 14.483315] fuse: init (API version 7.45) <7>[ 14.484408] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules... <7>[ 14.484520] systemd[1]: systemd-pcrmachine.service - TPM2 PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki). <7>[ 14.484590] systemd[1]: systemd-tpm2-setup-early.service - TPM2 SRK Setup (Early) was skipped because of an unmet condition check (ConditionSecurity=measured-uki). <6>[ 14.485997] pstore: Registered efi_pstore as persistent store backend <7>[ 14.488966] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices... <7>[ 14.494151] systemd[1]: Started systemd-journald.service - Journal Service. <6>[ 14.628433] EXT4-fs (nvme0n1p2): re-mounted 9a25468b-c3fd-45e2-b59f-4eab10a53c55 r/w. <6>[ 14.654024] Adding 8388604k swap on /swap.img. Priority:-2 extents:66 across:274595840k SS <7>[ 14.672572] systemd-journald[206]: Received client request to flush runtime journal. <7>[ 14.686622] systemd-journald[206]: /var/log/journal/2b6a2c75c75941a29794878cc3195815/system.journal: Journal file uses a different sequence number ID, rotating. <7>[ 14.686632] systemd-journald[206]: Rotating system journal. <4>[ 15.416506] nvme nvme0: using unchecked data buffer <6>[ 15.544468] intel_vsec 0000:00:0a.0: enabling device (0000 -> 0002) <6>[ 15.548793] intel_pmc_ssram_telemetry 0000:00:14.2: enabling device (0000 -> 0002) <6>[ 15.589709] input: Intel HID events as /devices/platform/INTC107B:00/input/input3 <6>[ 15.606329] intel-hid INTC107B:00: platform supports 5 button array <6>[ 15.624680] input: Intel HID 5 button array as /devices/platform/INTC107B:00/input/input4 <6>[ 15.728917] pci 0000:00:05.0: Setting to D3hot <6>[ 15.740896] pci 0000:00:0b.0: Setting to D3hot <5>[ 15.742145] audit: type=1400 audit(1762665591.375:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name=4D6F6E676F444220436F6D70617373 pid=425 comm="apparmor_parser" <5>[ 15.742598] audit: type=1400 audit(1762665591.375:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="Discord" pid=423 comm="apparmor_parser" <5>[ 15.743318] audit: type=1400 audit(1762665591.376:4): apparmor="STATUS" operation="profile_load" profile="unconfined" name="1password" pid=422 comm="apparmor_parser" <5>[ 15.743750] audit: type=1400 audit(1762665591.376:5): apparmor="STATUS" operation="profile_load" profile="unconfined" name="QtWebEngineProcess" pid=426 comm="apparmor_parser" <5>[ 15.744973] audit: type=1400 audit(1762665591.378:6): apparmor="STATUS" operation="profile_load" profile="unconfined" name="balena-etcher" pid=427 comm="apparmor_parser" <5>[ 15.749410] audit: type=1400 audit(1762665591.382:7): apparmor="STATUS" operation="profile_load" profile="unconfined" name="brave" pid=428 comm="apparmor_parser" <5>[ 15.750175] audit: type=1400 audit(1762665591.383:8): apparmor="STATUS" operation="profile_load" profile="unconfined" name="buildah" pid=429 comm="apparmor_parser" <5>[ 15.751268] audit: type=1400 audit(1762665591.384:9): apparmor="STATUS" operation="profile_load" profile="unconfined" name="busybox" pid=430 comm="apparmor_parser" <5>[ 15.753749] audit: type=1400 audit(1762665591.386:10): apparmor="STATUS" operation="profile_load" profile="unconfined" name="cam" pid=431 comm="apparmor_parser" <6>[ 15.756031] intel_pmc_core INT33A1:00: initialized <5>[ 15.759677] audit: type=1400 audit(1762665591.392:11): apparmor="STATUS" operation="profile_load" profile="unconfined" name="ch-checkns" pid=432 comm="apparmor_parser" <3>[ 15.807377] int3472-tps68470 i2c-INT3472:06: TPS68470 init error -121 <3>[ 15.807736] int3472-tps68470 i2c-INT3472:06: probe with driver int3472-tps68470 failed with error -121 <6>[ 16.152710] ACPI: bus type thunderbolt registered <6>[ 16.177608] intel_vpu 0000:00:0b.0: enabling device (0000 -> 0002) <6>[ 16.195747] intel_vpu 0000:00:0b.0: [drm] Firmware: intel/vpu/vpu_40xx_v0.0.bin, version: Jun 11 2024*LNL*ci_tag_ud202424_vpu_rc_20240611_0003*f3e8a8f27471d4127d8d92a8dc679b861ef43e43 <6>[ 16.195755] intel_vpu 0000:00:0b.0: [drm] Scheduler mode: OS <6>[ 16.196623] idma64 idma64.0: Found Intel integrated DMA 64-bit <6>[ 16.197135] idma64 idma64.1: Found Intel integrated DMA 64-bit <6>[ 16.219266] idma64 idma64.2: Found Intel integrated DMA 64-bit <6>[ 16.259891] idma64 idma64.3: Found Intel integrated DMA 64-bit <6>[ 16.267692] [drm] Initialized intel_vpu 1.0.0 for 0000:00:0b.0 on minor 0 <6>[ 16.318469] r8169 0000:7f:00.0: enabling device (0000 -> 0003) <6>[ 16.373895] proc_thermal_pci 0000:00:04.0: enabling device (0400 -> 0402) <6>[ 16.382300] intel_rapl_common: Found RAPL domain package <6>[ 16.382304] intel_rapl_common: Found RAPL domain dram <6>[ 16.395980] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer <6>[ 16.395986] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules <6>[ 16.395988] RAPL PMU: hw unit of domain package 2^-14 Joules <6>[ 16.395989] RAPL PMU: hw unit of domain dram 2^-14 Joules <6>[ 16.395990] RAPL PMU: hw unit of domain psys 2^-14 Joules <6>[ 16.454667] proc_thermal_pci 0000:00:04.0: msi enabled:1 msix enabled:0 <6>[ 16.527598] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002) <6>[ 16.529477] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 16.542140] r8169 0000:7f:00.0 eth0: RTL8168h/8111h, e4:fa:c4:a4:ee:2f, XID 541, IRQ 175 <6>[ 16.542146] r8169 0000:7f:00.0 eth0: jumbo features [frames: 9194 bytes, tx checksumming: ko] <6>[ 16.547466] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <4>[ 16.568341] block nvme0n1: No UUID available providing old NGUID <6>[ 16.782299] /proc/cgroups lists only v1 controllers, use cgroup.controllers of root cgroup for v2 info <6>[ 16.942480] intel_ish_ipc 0000:00:12.0: ISH loader: load firmware: intel/ish/ish_lnlm.bin <6>[ 16.955832] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 16.960048] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 16.968909] intel_ish_ipc 0000:00:12.0: ISH loader: firmware loaded. size:997888 <6>[ 16.968918] intel_ish_ipc 0000:00:12.0: ISH loader: FW base version: 5.8.0.7716 <6>[ 16.968920] intel_ish_ipc 0000:00:12.0: ISH loader: FW project version: 5.8.0.12472 <6>[ 16.969785] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.128289] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.133276] intel_rapl_common: Found RAPL domain package <6>[ 17.133281] intel_rapl_common: Found RAPL domain core <6>[ 17.133284] intel_rapl_common: Found RAPL domain dram <6>[ 17.133286] intel_rapl_common: Found RAPL domain psys <6>[ 17.147756] loop0: detected capacity change from 0 to 8 <6>[ 17.158920] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.211639] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <4>[ 17.259653] spi-nor spi0.0: supply vcc not found, using dummy regulator <6>[ 17.290505] r8169 0000:7f:00.0 enp127s0: renamed from eth0 <5>[ 17.342551] Creating 1 MTD partitions on "0000:00:1f.5": <5>[ 17.343160] 0x000000000000-0x000002000000 : "BIOS" <6>[ 17.374085] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.415937] Generic FE-GE Realtek PHY r8169-0-7f00:00: attached PHY driver (mii_bus:phy_addr=r8169-0-7f00:00, irq=MAC) <6>[ 17.577330] r8169 0000:7f:00.0 enp127s0: Link is Down <6>[ 17.623702] Consider using thermal netlink events interface <6>[ 17.959146] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 17.975635] hid: raw HID events driver (C) Jiri Kosina <6>[ 17.983358] ish-hid {33AECD58-B679-4E54-9BD9-A04D34F0C226}: [hid-ish]: enum_devices_done OK, num_hid_devices=6 <6>[ 18.017118] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.022213] hid-generic 001F:8087:0AC2.0001: hidraw0: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.023236] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.024006] hid-generic 001F:8087:0AC2.0002: hidraw1: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.025544] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.025642] hid-generic 001F:8087:0AC2.0003: hidraw2: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.026483] hid-generic 001F:8087:0AC2.0004: hidraw3: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.028125] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.028536] hid-generic 001F:8087:0AC3.0005: hidraw4: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 18.029349] hid-generic 001F:8087:0AC3.0006: hidraw5: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 18.030283] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.034683] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.036751] hid-sensor-hub 001F:8087:0AC2.0001: hidraw0: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.039482] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.041515] hid-sensor-hub 001F:8087:0AC2.0002: hidraw1: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.044239] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.046396] hid-sensor-hub 001F:8087:0AC2.0003: hidraw2: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.049744] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.049923] hid-sensor-hub 001F:8087:0AC2.0004: hidraw3: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC2] on <6>[ 18.052756] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.053581] hid-sensor-hub 001F:8087:0AC3.0005: hidraw4: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 18.056421] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.056422] hid-sensor-hub 001F:8087:0AC3.0006: hidraw5: SENSOR HUB HID v2.00 Device [hid-ishtp 8087:0AC3] on <6>[ 18.062206] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.137058] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.139709] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.145465] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.151185] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.157039] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.161943] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.168275] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.174287] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.179588] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.182579] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.187608] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.193945] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.200144] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.204773] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.209744] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.215740] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.222052] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.227534] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.233556] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 18.237961] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <6>[ 19.741559] typec port0: bound usb3-port1 (ops connector_ops) <6>[ 19.741604] typec port0: bound usb2-port1 (ops connector_ops) <6>[ 19.741652] typec port0: bound usb4_port1 (ops connector_ops [thunderbolt]) <6>[ 20.774727] typec port1: bound usb3-port2 (ops connector_ops) <6>[ 20.774785] typec port1: bound usb2-port2 (ops connector_ops) <6>[ 20.774834] typec port1: bound usb4_port3 (ops connector_ops [thunderbolt]) <6>[ 21.176055] r8169 0000:7f:00.0 enp127s0: Link is Up - 1Gbps/Full - flow control off <7>[ 27.553572] systemd-journald[206]: /var/log/journal/2b6a2c75c75941a29794878cc3195815/user-1000.journal: Journal file uses a different sequence number ID, rotating. <6>[ 28.240520] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <4>[ 28.241468] pci 0000:00:1f.3: deferred probe pending: snd_hda_intel: couldn't bind with audio component <7>[ 52.432163] [IGT] xe_module_load: executing <4>[ 52.432208] NOTICE: Automounting of tracing to debugfs is deprecated and will be removed in 2030 <7>[ 52.439487] [IGT] xe_module_load: starting subtest load <5>[ 52.686112] Setting dangerous option force_probe - tainting kernel <6>[ 52.689043] xe 0000:00:02.0: vgaarb: deactivate vga console <6>[ 52.690669] xe 0000:00:02.0: [drm] Found lunarlake (device ID 64a0) integrated display version 20.00 stepping B0 <7>[ 52.690680] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] LUNARLAKE 64a0:0004 dgfx:0 gfx:Xe2_LPG (20.04) media:Xe2_LPM (20.00) display:yes dma_m_s:46 tc:1 gscfi:0 cscfi:0 <7>[ 52.690792] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] Stepping = (G:B0, M:B0, B:**) <7>[ 52.690897] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] SR-IOV support: no (mode: none) <7>[ 52.692918] xe 0000:00:02.0: [drm:xe_ttm_stolen_mgr_init [xe]] Initialized stolen memory support with 58720256 bytes <7>[ 52.693174] xe 0000:00:02.0: [drm:intel_pch_detect [xe]] PCH not involved in display, using fake PCH type 1027 for south display <7>[ 52.693280] xe 0000:00:02.0: [drm:intel_dmc_wl_init [xe]] Sanitized enable_dmc_wl value: 0 (disabled) <7>[ 52.693392] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] graphic opregion physical addr: 0x6ff04018 <7>[ 52.693507] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] ACPI OpRegion version 3.2.0 <7>[ 52.693605] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] Public ACPI methods supported <7>[ 52.693702] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] ASLE supported <7>[ 52.693797] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] ASLE extension supported <7>[ 52.693895] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] Mailbox #2 for backlight present <7>[ 52.694034] xe 0000:00:02.0: [drm:intel_opregion_setup [xe]] Found valid VBT in ACPI OpRegion (RVDA) <7>[ 52.694137] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] DRAM type: LPDDR5 <7>[ 52.694255] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] DRAM channels: 8 <7>[ 52.694371] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] Num QGV points 4 <7>[ 52.694473] xe 0000:00:02.0: [drm:intel_dram_detect [xe]] Num PSF GV points 0 <7>[ 52.694573] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 0: DCLK=2400 tRP=48 tRDPRE=40 tRAS=104 tRCD=48 tRC=152 <7>[ 52.694676] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 1: DCLK=4800 tRP=88 tRDPRE=72 tRAS=208 tRCD=88 tRC=296 <7>[ 52.694778] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 2: DCLK=6400 tRP=120 tRDPRE=80 tRAS=272 tRCD=120 tRC=392 <7>[ 52.694891] xe 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [xe]] QGV 3: DCLK=8534 tRP=160 tRDPRE=96 tRAS=360 tRCD=160 tRC=520 <7>[ 52.694994] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 0: num_planes=0 deratedbw=23530 peakbw: 38400 <7>[ 52.695096] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 1: num_planes=0 deratedbw=36260 peakbw: 76800 <7>[ 52.695191] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 52.695282] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW0 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 52.695373] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 0: num_planes=0 deratedbw=27998 peakbw: 38400 <7>[ 52.695463] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 52.695553] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 52.695642] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW1 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 52.695730] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 0: num_planes=0 deratedbw=30935 peakbw: 38400 <7>[ 52.695821] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 52.695916] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 52.696010] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW2 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 52.696104] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 0: num_planes=0 deratedbw=32647 peakbw: 38400 <7>[ 52.696194] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 52.696279] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 52.696371] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW3 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 52.696462] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 0: num_planes=0 deratedbw=33577 peakbw: 38400 <7>[ 52.696553] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 52.696644] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 52.696726] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW4 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 52.696808] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 0: num_planes=0 deratedbw=34061 peakbw: 38400 <7>[ 52.696912] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 1: num_planes=0 deratedbw=38000 peakbw: 76800 <7>[ 52.697005] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 2: num_planes=0 deratedbw=38000 peakbw: 102400 <7>[ 52.697097] xe 0000:00:02.0: [drm:tgl_get_bw_info.isra.0 [xe]] BW5 / QGV 3: num_planes=0 deratedbw=38000 peakbw: 136544 <7>[ 52.697189] xe 0000:00:02.0: [drm:intel_display_device_info_runtime_init [xe]] rawclk rate: 38400 kHz <7>[ 52.697647] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Set default to SSC at 120000 kHz <7>[ 52.697805] xe 0000:00:02.0: [drm:intel_bios_init [xe]] VBT signature "$VBT LUNARLAKE ", BDB version 262 <7>[ 52.697941] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 1 (size 10, min size 7) <7>[ 52.698060] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 2 (size 405, min size 5) <7>[ 52.698168] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 9 (size 100, min size 100) <7>[ 52.698275] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 12 (size 19, min size 19) <7>[ 52.698384] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 27 (size 850, min size 848) <7>[ 52.698499] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 40 (size 34, min size 34) <7>[ 52.698606] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Generating LFP data table pointers <7>[ 52.698719] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 41 (size 148, min size 148) <7>[ 52.698824] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 42 (size 1382, min size 1366) <7>[ 52.698942] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 43 (size 305, min size 305) <7>[ 52.699061] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 44 (size 136, min size 136) <7>[ 52.699168] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 52 (size 822, min size 822) <7>[ 52.699260] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found BDB block 56 (size 210, min size 210) <7>[ 52.699348] xe 0000:00:02.0: [drm:intel_bios_init [xe]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0 <7>[ 52.699436] xe 0000:00:02.0: [drm:intel_bios_init [xe]] crt_ddc_bus_pin: 2 <7>[ 52.699523] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x1806 <7>[ 52.699614] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x68c6 <7>[ 52.699703] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x68c6 <7>[ 52.699795] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Found VBT child device with type 0x68c6 <7>[ 52.699915] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Skipping SDVO device mapping <7>[ 52.700031] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7>[ 52.700140] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7>[ 52.700225] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7>[ 52.700309] xe 0000:00:02.0: [drm:intel_bios_init [xe]] Port F VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7>[ 52.700396] xe 0000:00:02.0: [drm:intel_power_domains_init [xe]] Allowed DC state mask 0a <7>[ 52.700508] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 00 <7>[ 52.700654] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_1 <7>[ 52.700787] xe 0000:00:02.0: [drm:intel_cdclk_init_hw [xe]] Current CDCLK 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7>[ 52.701200] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf <7>[ 52.701381] xe 0000:00:02.0: [drm:icl_display_core_init [xe]] Unknown memory configuration; disabling address buddy logic. <7>[ 52.701517] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on <7>[ 52.701624] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 52.701737] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 00 <7>[ 52.701929] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_2 <6>[ 52.702070] xe 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=none:owns=io+mem <7>[ 52.702089] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A <7>[ 52.702227] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_B <7>[ 52.702338] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_C <7>[ 52.702438] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_D <7>[ 52.702653] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PICA_TC <7>[ 52.703176] xe 0000:00:02.0: [drm:intel_dmc_init [xe]] Loading i915/xe2lpd_dmc.bin <7>[ 52.704558] xe 0000:00:02.0: [drm:intel_fbc_init [xe]] Sanitized enable_fbc value: 1 <7>[ 52.705020] xe 0000:00:02.0: [drm:skl_wm_init [xe]] SAGV supported: yes, original SAGV block time: 12 us <7>[ 52.705147] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM0 latency not provided <7>[ 52.705241] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM1 latency 100 (100.0 usec) <7>[ 52.705333] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM2 latency 100 (100.0 usec) <7>[ 52.705422] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM3 latency 100 (100.0 usec) <7>[ 52.705509] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM4 latency 93 (93.0 usec) <7>[ 52.705597] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] original WM5 latency 100 (100.0 usec) <7>[ 52.705684] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM0 latency 6 (6.0 usec) <7>[ 52.705772] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM1 latency 106 (106.0 usec) <7>[ 52.705880] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM2 latency 106 (106.0 usec) <7>[ 52.705991] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM3 latency 106 (106.0 usec) <7>[ 52.706099] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM4 latency 106 (106.0 usec) <7>[ 52.706183] xe 0000:00:02.0: [drm:intel_print_wm_latency [xe]] adjusted WM5 latency 106 (106.0 usec) <7>[ 52.706440] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 0: <7>[ 52.706561] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x8f074 = 0x86fc0 <7>[ 52.706666] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x8f034 = 0xc003b400 (EVT_CTL) <7>[ 52.706767] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x8f004 = 0x4240408 (EVT_HTP) <7>[ 52.706889] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x8f044 = 0xc0023200 (EVT_CTL) <7>[ 52.707020] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x8f014 = 0x57c45700 (EVT_HTP) <7>[ 52.707153] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 1: <7>[ 52.707265] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x5f074 = 0x97fc0 <7>[ 52.707363] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x5f040 = 0xc0033100 (EVT_CTL) (disabling) <7>[ 52.707460] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x5f010 = 0x28542840 (EVT_HTP) <7>[ 52.707564] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x5f03c = 0xc0032d00 (EVT_CTL) (disabling) <7>[ 52.707665] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x5f00c = 0x29802864 (EVT_HTP) <7>[ 52.707766] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[5]: 0x5f044 = 0xc0033200 (EVT_CTL) (disabling) <7>[ 52.707916] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[6]: 0x5f014 = 0x398c394c (EVT_HTP) <7>[ 52.708046] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 2: <7>[ 52.708154] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x5f474 = 0x9ffc0 <7>[ 52.708267] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x5f440 = 0xc0033100 (EVT_CTL) (disabling) <7>[ 52.708376] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x5f410 = 0xa9bca9a8 (EVT_HTP) <7>[ 52.708471] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x5f43c = 0xc0032d00 (EVT_CTL) (disabling) <7>[ 52.708560] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x5f40c = 0xaae8a9cc (EVT_HTP) <7>[ 52.708665] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[5]: 0x5f444 = 0xc0033200 (EVT_CTL) (disabling) <7>[ 52.708754] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[6]: 0x5f414 = 0xbabcba7c (EVT_HTP) <7>[ 52.708856] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] DMC 3: <7>[ 52.708961] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[0]: 0x5f874 = 0x547c0 <7>[ 52.709066] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[1]: 0x5f840 = 0xc0033100 (EVT_CTL) (disabling) <7>[ 52.709170] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[2]: 0x5f810 = 0x26dc26c8 (EVT_HTP) <7>[ 52.709273] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[3]: 0x5f83c = 0xc0032d00 (EVT_CTL) (disabling) <7>[ 52.709375] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[4]: 0x5f80c = 0x280826ec (EVT_HTP) <7>[ 52.709471] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[5]: 0x5f844 = 0xc0033200 (EVT_CTL) (disabling) <7>[ 52.709557] xe 0000:00:02.0: [drm:dmc_load_work_fn [xe]] mmio[6]: 0x5f814 = 0x37dc379c (EVT_HTP) <7>[ 52.711157] xe 0000:00:02.0: [drm:intel_display_driver_probe_nogem [xe]] 3 display pipes available. <7>[ 52.714144] xe 0000:00:02.0: [drm:intel_cdclk_read_hw [xe]] Current CDCLK 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7>[ 52.714296] xe 0000:00:02.0: [drm:intel_update_max_cdclk [xe]] Max CD clock rate: 652800 kHz <7>[ 52.714443] xe 0000:00:02.0: [drm:intel_update_max_cdclk [xe]] Max dotclock rate: 1305600 kHz <7>[ 52.714623] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:207:DDI A/PHY A] Using AUX CH A (VBT) <7>[ 52.714837] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding eDP connector on [ENCODER:207:DDI A/PHY A] <7>[ 52.715043] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel type (VBT): 2 <7>[ 52.715181] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Selected panel type (VBT): 2 <7>[ 52.715316] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] DRRS supported mode is seamless <7>[ 52.715456] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7>[ 52.715603] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] VBT initial LVDS value 300 <7>[ 52.715736] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel manufacturer name: MS_, product code: 3, serial number: 3, year of manufacture: 2002 <7>[ 52.715889] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Panel name: LFP_PanelName <7>[ 52.716025] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] Seamless DRRS min refresh rate: 0 Hz <7>[ 52.716162] xe 0000:00:02.0: [drm:intel_bios_init_panel [xe]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0 <7>[ 52.716321] xe 0000:00:02.0: [drm:intel_pps_init [xe]] [ENCODER:207:DDI A/PHY A] initial power sequencer: PPS 0 <7>[ 52.716485] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] bios power_up 1 backlight_on 1 backlight_off 1 power_down 500 power_cycle 5000 <7>[ 52.716614] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000 <7>[ 52.716737] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100 <7>[ 52.716870] xe 0000:00:02.0: [drm:pps_init_delays [xe]] panel power up delay 200, power down delay 50, power cycle delay 500 <7>[ 52.716992] xe 0000:00:02.0: [drm:pps_init_delays [xe]] backlight on delay 1, off delay 200 <7>[ 52.717267] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7>[ 52.717565] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A <7>[ 52.718862] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turning VDD on <7>[ 52.719164] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f <7>[ 52.720734] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80 <7>[ 52.721046] xe 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 7.3 SW-rev 0.0 quirks 0x0000 <6>[ 52.721121] xe 0000:00:02.0: [drm] Finished loading DMC firmware i915/xe2lpd_dmc.bin (v2.29) <7>[ 52.721462] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] eDP DPCD: 05 83 85 04 1e <7>[ 52.722009] xe 0000:00:02.0: [drm:intel_psr_init_dpcd [xe]] eDP panel supports PSR version 3 <7>[ 52.722341] xe 0000:00:02.0: [drm:intel_psr_init_dpcd [xe]] PSR2 supported <7>[ 52.724106] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 52.733445] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 52.733457] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 52.733459] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 52.733460] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7>[ 52.733463] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 52.733466] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 52.733468] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD monitor <5>[ 52.733473] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 52.733474] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD size 20, SAD count 0 <5>[ 52.733477] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 52.733513] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 52.733514] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 52.733516] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 52.733530] xe 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [xe]] [CONNECTOR:208:eDP-1] using preferred EDID fixed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 52.733670] xe 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [xe]] [CONNECTOR:208:eDP-1] using alternate EDID fixed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 52.734028] xe 0000:00:02.0: [drm:intel_dp_wait_source_oui [xe]] [CONNECTOR:208:eDP-1] Performing OUI wait (0 ms) <7>[ 52.734384] xe 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [xe]] [CONNECTOR:208:eDP-1] Detected unsupported HDR backlight interface version 0 <7>[ 52.734526] xe 0000:00:02.0: [drm:intel_panel_init [xe]] [CONNECTOR:208:eDP-1] DRRS type: seamless <7>[ 52.734689] xe 0000:00:02.0: [drm:cnp_setup_backlight [xe]] [CONNECTOR:208:eDP-1] Using native PCH PWM for backlight control (controller=0) <7>[ 52.734865] xe 0000:00:02.0: [drm:intel_backlight_setup [xe]] [CONNECTOR:208:eDP-1] backlight initialized, enabled, brightness 192000/192000 <7>[ 52.735064] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] bios power_up 1 backlight_on 1 backlight_off 1 power_down 500 power_cycle 5000 <7>[ 52.735183] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000 <7>[ 52.735279] xe 0000:00:02.0: [drm:intel_pps_dump_state [xe]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100 <7>[ 52.735372] xe 0000:00:02.0: [drm:pps_init_delays [xe]] panel power up delay 200, power down delay 50, power cycle delay 500 <7>[ 52.735464] xe 0000:00:02.0: [drm:pps_init_delays [xe]] backlight on delay 1, off delay 200 <7>[ 52.735586] xe 0000:00:02.0: [drm:pps_init_registers [xe]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7>[ 52.735786] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:216:DDI TC1/PHY TC1] Using AUX CH USBC1 (VBT) <7>[ 52.736006] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port D/TC#1: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected) <7>[ 52.736161] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:216:DDI TC1/PHY TC1] <7>[ 52.736530] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:228:DDI TC2/PHY TC2] Using AUX CH USBC2 (VBT) <7>[ 52.736661] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port E/TC#2: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected) <7>[ 52.736780] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:228:DDI TC2/PHY TC2] <7>[ 52.737076] xe 0000:00:02.0: [drm:intel_dp_aux_ch [xe]] [ENCODER:236:DDI TC3/PHY TC3] Using AUX CH USBC3 (VBT) <7>[ 52.737220] xe 0000:00:02.0: [drm:tc_phy_get_current_mode [xe]] Port F/TC#3: PHY mode: tbt-alt (ready: no, owned: no, HPD: disconnected) <7>[ 52.737338] xe 0000:00:02.0: [drm:intel_dp_init_connector [xe]] Adding DP connector on [ENCODER:236:DDI TC3/PHY TC3] <7>[ 52.737808] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:88:pipe A] hw state readout: enabled <7>[ 52.737966] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:146:pipe B] hw state readout: disabled <7>[ 52.738129] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:204:pipe C] hw state readout: disabled <7>[ 52.738240] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:33:plane 1A] hw state readout: enabled, pipe A <7>[ 52.738331] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:43:plane 2A] hw state readout: disabled, pipe A <7>[ 52.738419] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:53:plane 3A] hw state readout: disabled, pipe A <7>[ 52.738506] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:63:plane 4A] hw state readout: disabled, pipe A <7>[ 52.738592] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:73:plane 5A] hw state readout: disabled, pipe A <7>[ 52.738678] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:83:cursor A] hw state readout: disabled, pipe A <7>[ 52.738762] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:91:plane 1B] hw state readout: disabled, pipe B <7>[ 52.738866] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:101:plane 2B] hw state readout: disabled, pipe B <7>[ 52.738974] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:111:plane 3B] hw state readout: disabled, pipe B <7>[ 52.739082] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:121:plane 4B] hw state readout: disabled, pipe B <7>[ 52.739178] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:131:plane 5B] hw state readout: disabled, pipe B <7>[ 52.739259] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:141:cursor B] hw state readout: disabled, pipe B <7>[ 52.739339] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:149:plane 1C] hw state readout: disabled, pipe C <7>[ 52.739418] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:159:plane 2C] hw state readout: disabled, pipe C <7>[ 52.739497] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:169:plane 3C] hw state readout: disabled, pipe C <7>[ 52.739576] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:179:plane 4C] hw state readout: disabled, pipe C <7>[ 52.739654] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:189:plane 5C] hw state readout: disabled, pipe C <7>[ 52.739732] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:199:cursor C] hw state readout: disabled, pipe C <7>[ 52.740517] xe 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [xe]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp <7>[ 52.740630] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:207:DDI A/PHY A] hw state readout: enabled, pipe A <7>[ 52.740721] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port D/TC#1: sanitize mode (disconnected) pin assignment: - max lanes: 4 <7>[ 52.740810] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:216:DDI TC1/PHY TC1] hw state readout: disabled, pipe A <7>[ 52.740924] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:218:DP-MST A] hw state readout: disabled, pipe A <7>[ 52.741028] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:219:DP-MST B] hw state readout: disabled, pipe B <7>[ 52.741131] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:220:DP-MST C] hw state readout: disabled, pipe C <7>[ 52.741235] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port E/TC#2: sanitize mode (disconnected) pin assignment: - max lanes: 4 <7>[ 52.741320] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:228:DDI TC2/PHY TC2] hw state readout: disabled, pipe A <7>[ 52.741399] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:230:DP-MST A] hw state readout: disabled, pipe A <7>[ 52.741475] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:231:DP-MST B] hw state readout: disabled, pipe B <7>[ 52.741549] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:232:DP-MST C] hw state readout: disabled, pipe C <7>[ 52.741629] xe 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [xe]] Port F/TC#3: sanitize mode (disconnected) pin assignment: - max lanes: 4 <7>[ 52.741711] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:236:DDI TC3/PHY TC3] hw state readout: disabled, pipe A <7>[ 52.741787] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:238:DP-MST A] hw state readout: disabled, pipe A <7>[ 52.741873] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:239:DP-MST B] hw state readout: disabled, pipe B <7>[ 52.741955] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [ENCODER:240:DP-MST C] hw state readout: disabled, pipe C <7>[ 52.742063] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:208:eDP-1] hw state readout: enabled <7>[ 52.742167] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:217:DP-1] hw state readout: disabled <7>[ 52.742263] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:229:DP-2] hw state readout: disabled <7>[ 52.742354] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CONNECTOR:237:DP-3] hw state readout: disabled <7>[ 52.742505] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:33:plane 1A] min_cdclk 173855 kHz <7>[ 52.742587] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:43:plane 2A] min_cdclk 0 kHz <7>[ 52.742663] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:53:plane 3A] min_cdclk 0 kHz <7>[ 52.742737] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:63:plane 4A] min_cdclk 0 kHz <7>[ 52.742810] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:73:plane 5A] min_cdclk 0 kHz <7>[ 52.742907] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:83:cursor A] min_cdclk 0 kHz <7>[ 52.743003] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:88:pipe A] min_cdclk 173855 kHz <7>[ 52.743097] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:91:plane 1B] min_cdclk 0 kHz <7>[ 52.743186] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:101:plane 2B] min_cdclk 0 kHz <7>[ 52.743259] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:111:plane 3B] min_cdclk 0 kHz <7>[ 52.743330] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:121:plane 4B] min_cdclk 0 kHz <7>[ 52.743401] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:131:plane 5B] min_cdclk 0 kHz <7>[ 52.743474] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:141:cursor B] min_cdclk 0 kHz <7>[ 52.743550] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:146:pipe B] min_cdclk 0 kHz <7>[ 52.743626] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:149:plane 1C] min_cdclk 0 kHz <7>[ 52.743700] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:159:plane 2C] min_cdclk 0 kHz <7>[ 52.743773] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:169:plane 3C] min_cdclk 0 kHz <7>[ 52.743861] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:179:plane 4C] min_cdclk 0 kHz <7>[ 52.743956] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:189:plane 5C] min_cdclk 0 kHz <7>[ 52.744050] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [PLANE:199:cursor C] min_cdclk 0 kHz <7>[ 52.744140] xe 0000:00:02.0: [drm:intel_modeset_setup_hw_state [xe]] [CRTC:204:pipe C] min_cdclk 0 kHz <7>[ 52.744362] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:88:pipe A] dbuf slices 0x3, ddb (0 - 2048), active pipes 0x1, mbus joined: no <7>[ 52.744443] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:146:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7>[ 52.744524] xe 0000:00:02.0: [drm:skl_wm_get_hw_state [xe]] [CRTC:204:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7>[ 52.744603] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe A data rate 1390840 num active planes 1 <7>[ 52.744705] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe B data rate 0 num active planes 0 <7>[ 52.744804] xe 0000:00:02.0: [drm:intel_bw_update_hw_state [xe]] pipe C data rate 0 num active planes 0 <7>[ 52.744954] xe 0000:00:02.0: [drm:intel_cmtg_sanitize [xe]] CMTG readout: CMTG A: enabled, CMTG B: disabled, Transcoder A secondary: yes, Transcoder B secondary: no <7>[ 52.745063] xe 0000:00:02.0: [drm:intel_cmtg_sanitize [xe]] Disabling CMTG A <7>[ 52.745296] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:88:pipe A] enable: yes [setup_hw_state] <7>[ 52.745406] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7>[ 52.745514] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 24, dithering: 0 <7>[ 52.745617] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <7>[ 52.745711] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: , slave transcoder bitmask = 0x0 <7>[ 52.745803] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7>[ 52.745913] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7>[ 52.746015] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8102230, data_n: 8388608, link_m: 675185, link_n: 524288, tu: 64 <7>[ 52.746118] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7>[ 52.746218] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7>[ 52.746309] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7>[ 52.746398] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled <7>[ 52.746485] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7>[ 52.746571] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7>[ 52.746657] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7>[ 52.746742] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 1 <7>[ 52.746831] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: yes, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 105 vsync start: 103, vsync end: 96 <7>[ 52.746940] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1801, vmax vblank: 1801, vmin vtotal: 1906, vmax vtotal: 1906 <7>[ 52.747052] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 52.747163] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 52.747248] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1801-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 52.747333] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 52.747419] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1801-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 52.747508] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 270000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7>[ 52.747596] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7>[ 52.747681] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7>[ 52.747766] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7>[ 52.747873] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7>[ 52.747963] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dpll_hw_state: dpll: 0x41eb0, dpll_md: 0xf42110, fp0: 0xf8, fp1: 0x1000000 <7>[ 52.748053] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x20000000 gamma_mode: 0x20000000 gamma_enable: 0 csc_enable: 0 <7>[ 52.748140] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7>[ 52.748222] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 52.748302] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 52.748379] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 52.748457] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 52.748534] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 52.748611] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 52.748688] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 52.748764] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 52.748848] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 52.748932] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 52.749015] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7>[ 52.749104] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:146:pipe B] enable: no [setup_hw_state] <7>[ 52.749191] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:204:pipe C] enable: no [setup_hw_state] <7>[ 52.749494] xe 0000:00:02.0: [drm:skl_get_initial_plane_config [xe]] [CRTC:88:pipe A][PLANE:33:plane 1A] with fb: size=2880x1800@32, offset=fec00000, pitch 11520, size 0x13c6800 <7>[ 52.749584] xe 0000:00:02.0: [drm:intel_plane_disable_noatomic [xe]] Disabling [PLANE:33:plane 1A] on [CRTC:88:pipe A] <6>[ 52.773634] xe 0000:00:02.0: [drm] Tile0: GT0: Using GuC firmware from xe/lnl_guc_70.bin version 70.53.0 <7>[ 52.777450] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 0] = 0x003543f7 <7>[ 52.777567] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 1] = 0x00000000 <7>[ 52.777656] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 2] = 0x00000000 <7>[ 52.777732] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 3] = 0x00000001 <7>[ 52.777804] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 4] = 0x000008d2 <7>[ 52.777894] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 5] = 0x64a00004 <7>[ 52.777967] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 6] = 0x00000000 <7>[ 52.778036] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 7] = 0x00000000 <7>[ 52.778103] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 8] = 0x00000000 <7>[ 52.778169] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 9] = 0x00000000 <7>[ 52.778233] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[10] = 0x00000000 <7>[ 52.778293] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[11] = 0x00000000 <7>[ 52.778351] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[12] = 0x00000000 <7>[ 52.778409] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[13] = 0x00000000 <7>[ 52.778468] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] WOPCM: 2048K <7>[ 52.778571] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] GuC WOPCM is already locked [6144K, 832K) <7>[ 52.788889] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT0: GuC load: init took 9ms, freq = 1850MHz (req = 1850MHz), before = 1850MHz, status = 0x8002F034 <7>[ 52.789880] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled <7>[ 52.790314] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: dss mask (geometry): 00000000,00000000,0000007f <7>[ 52.790472] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: dss mask (compute): 00000000,00000000,0000007f <7>[ 52.790599] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: EU mask per DSS: 000000ff <7>[ 52.790722] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: EU type: simd16 <7>[ 52.790855] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT0: L3 bank mask: 00000000,000000ff <6>[ 53.431599] xe 0000:00:02.0: [drm] Tile0: GT0: ccs1 fused off <6>[ 53.431602] xe 0000:00:02.0: [drm] Tile0: GT0: ccs2 fused off <6>[ 53.431603] xe 0000:00:02.0: [drm] Tile0: GT0: ccs3 fused off <7>[ 53.431733] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add rcs0 whitelist to engine <7>[ 53.431863] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdafc-0xdaff]: allow read access <7>[ 53.431979] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb00-0xdb1f]: allow read access <7>[ 53.432098] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb1c-0xdb1f]: allow rw access <7>[ 53.432252] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add bcs0 whitelist to engine <7>[ 53.432374] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add bcs8 whitelist to engine <7>[ 53.432512] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: Add ccs0 whitelist to engine <7>[ 53.432602] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdafc-0xdaff]: allow read access <7>[ 53.432689] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb00-0xdb1f]: allow read access <7>[ 53.432774] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT0: REG[0xdb1c-0xdb1f]: allow rw access <7>[ 53.433855] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying GT save-restore MMIOs <7>[ 53.433964] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x4148] = 0x00000000 <7>[ 53.434084] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x8828] = 0x00800000 <7>[ 53.434191] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb104] = 0x08104440 <7>[ 53.434276] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb108] = 0x30200000 <7>[ 53.434360] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb154] = 0x00020000 <7>[ 53.434442] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xb158] = 0x0000007f <7>[ 53.434521] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: flag:0x1 <7>[ 53.434601] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: mocs entries: 16 <7>[ 53.434679] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[0] 0x4000 0xc <7>[ 53.434759] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[1] 0x4004 0x10c <7>[ 53.434849] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[2] 0x4008 0x130 <7>[ 53.434927] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[3] 0x400c 0x13c <7>[ 53.435018] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[4] 0x4010 0x100 <7>[ 53.435109] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[5] 0x4014 0x100 <7>[ 53.435199] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[6] 0x4018 0x100 <7>[ 53.435280] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[7] 0x401c 0x100 <7>[ 53.435353] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[8] 0x4020 0x100 <7>[ 53.435427] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[9] 0x4024 0x100 <7>[ 53.435500] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[10] 0x4028 0x100 <7>[ 53.435575] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[11] 0x402c 0x100 <7>[ 53.435652] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[12] 0x4030 0x100 <7>[ 53.435727] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[13] 0x4034 0x100 <7>[ 53.435800] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[14] 0x4038 0x100 <7>[ 53.435887] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT0: GLOB_MOCS[15] 0x403c 0x100 <7>[ 53.435970] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying rcs0 save-restore MMIOs <7>[ 53.436066] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x2050] = 0x10001000 <7>[ 53.436160] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x20c4] = 0x3f7e0306 <7>[ 53.436246] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x20d4] = 0xc080c080 <7>[ 53.436321] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x24d0] = 0x1000dafc <7>[ 53.436394] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x24d4] = 0x1000db01 <7>[ 53.436467] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x24d8] = 0x0000db1c <7>[ 53.436541] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe194] = 0x00400040 <7>[ 53.436617] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe48c] = 0x02000200 <7>[ 53.436696] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe49c] = 0x40004000 <7>[ 53.436776] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe4c4] = 0x08400840 <7>[ 53.436866] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe4f0] = 0x00020002 <7>[ 53.436957] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe530] = 0x00000400 <7>[ 53.437043] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe7c8] = 0x00002000 <7>[ 53.437127] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0xe7cc] = 0x00009000 <7>[ 53.437462] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying bcs0 save-restore MMIOs <7>[ 53.437538] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x22050] = 0x10001000 <7>[ 53.437611] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x220c4] = 0x3f7e0306 <7>[ 53.437683] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x220d4] = 0xc080c080 <7>[ 53.437932] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying bcs8 save-restore MMIOs <7>[ 53.438018] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x3ee050] = 0x10001000 <7>[ 53.438108] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x3ee0c4] = 0x3f7e0306 <7>[ 53.438196] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x3ee0d4] = 0xc080c080 <7>[ 53.438520] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: Applying ccs0 save-restore MMIOs <7>[ 53.438601] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a050] = 0x10001000 <7>[ 53.438668] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a0c4] = 0x3f7e0306 <7>[ 53.438732] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a0d4] = 0xc080c080 <7>[ 53.438798] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a4d0] = 0x1000dafc <7>[ 53.438877] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a4d4] = 0x1000db01 <7>[ 53.438959] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT0: REG[0x1a4d8] = 0x0000db1c <7>[ 53.439534] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled <7>[ 53.439668] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 0] = 0x003543f7 <7>[ 53.439748] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 1] = 0x00000800 <7>[ 53.439839] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 2] = 0x00000014 <7>[ 53.439927] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 3] = 0x00000001 <7>[ 53.440018] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 4] = 0x000008d2 <7>[ 53.440105] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 5] = 0x64a00004 <7>[ 53.440191] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 6] = 0x00000000 <7>[ 53.440272] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 7] = 0x00000000 <7>[ 53.440343] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 8] = 0x00000000 <7>[ 53.440414] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[ 9] = 0x00000000 <7>[ 53.440487] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[10] = 0x00000000 <7>[ 53.440561] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[11] = 0x00000000 <7>[ 53.440635] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[12] = 0x00000000 <7>[ 53.440708] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT0: GuC param[13] = 0x00000000 <7>[ 53.440805] xe 0000:00:02.0: [drm:xe_guc_id_mgr_init [xe]] Tile0: GT0: using 65535 GuC IDs <7>[ 53.441337] xe 0000:00:02.0: [drm:xe_guc_db_mgr_init [xe]] Tile0: GT0: using 256 doorbells <7>[ 53.442762] xe 0000:00:02.0: [drm:xe_guc_buf_cache_init [xe]] Tile0: GT0: reusable buffer with 2048 dwords at 0xd19000 for xe_guc_init_post_hwconfig [xe] <7>[ 53.445361] xe 0000:00:02.0: [drm:xe_guc_capture_steered_list_init [xe]] Tile0: GT0: capture found 42 ext-regs. <7>[ 53.461787] xe 0000:00:02.0: [drm:xe_guc_ads_populate [xe]] Tile0: GT0: Updated ADS capture size 20480 (was 45056) <7>[ 53.472666] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT0: GuC load: init took 10ms, freq = 1850MHz (req = 1850MHz), before = 1850MHz, status = 0x8002F034 <7>[ 53.472992] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled <7>[ 53.473905] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: LRC rcs0 WA job: 4138 dwords <7>[ 53.474033] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x5588] = 0x04000400 <7>[ 53.474122] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x6204] = 0x00400040 <7>[ 53.474202] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x6208] = 0x00200020 <7>[ 53.474274] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x62a8] = 0x02400240 <7>[ 53.474344] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x7010] = 0x40004000 <7>[ 53.474412] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x7044] = 0x04200420 <7>[ 53.474482] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x83a8] = 0x20002000 <7>[ 53.474547] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x6210] = ~0x18000|0x18000 <7>[ 53.477256] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: LRC bcs0 WA job: 27 dwords <7>[ 53.477405] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: REG[0x22204] = ~0x7e7e|0x606 <7>[ 53.477489] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT0: No non-register state to emit on graphics ver 20.04 <7>[ 53.479350] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT0: LRC ccs0 WA job: 0 dwords <7>[ 53.479448] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT0: No non-register state to emit on graphics ver 20.04 <6>[ 53.484320] xe 0000:00:02.0: [drm] Tile0: GT1: Using GuC firmware from xe/lnl_guc_70.bin version 70.53.0 <7>[ 53.489156] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 0] = 0x00df63f7 <7>[ 53.489343] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 1] = 0x00000000 <7>[ 53.489509] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 2] = 0x00000000 <7>[ 53.489674] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 3] = 0x00000001 <7>[ 53.489890] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 4] = 0x00001e16 <7>[ 53.490056] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 5] = 0x64a00004 <7>[ 53.490218] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 6] = 0x00000000 <7>[ 53.490403] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 7] = 0x00000000 <7>[ 53.490581] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 8] = 0x00000000 <7>[ 53.490770] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 9] = 0x00000000 <7>[ 53.490954] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[10] = 0x00000000 <7>[ 53.491114] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[11] = 0x00000000 <7>[ 53.491264] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[12] = 0x00000000 <7>[ 53.491416] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[13] = 0x00000000 <6>[ 53.493530] xe 0000:00:02.0: [drm] Tile0: GT1: Using HuC firmware from xe/lnl_huc.bin version 9.4.13 <6>[ 53.496441] xe 0000:00:02.0: [drm] Tile0: GT1: Using GSC firmware from xe/lnl_gsc_1.bin version 104.0.5.1429 <6>[ 53.497733] mei_gsc_proxy 0000:00:16.0-0f73db04-97ab-4125-b893-e904ad0d5464: bound 0000:00:02.0 (ops xe_gsc_proxy_component_ops [xe]) <7>[ 53.497898] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] WOPCM: 2048K <7>[ 53.498078] xe 0000:00:02.0: [drm:xe_wopcm_init [xe]] GuC WOPCM is already locked [5136K, 832K) <7>[ 53.518875] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT1: GuC load: init took 19ms, freq = 800MHz (req = 800MHz), before = 800MHz, status = 0x8002F034 <7>[ 53.519381] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled <7>[ 53.519609] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: dss mask (geometry): 00000000,00000000,00000000 <7>[ 53.519813] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: dss mask (compute): 00000000,00000000,00000000 <7>[ 53.520069] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: EU mask per DSS: 00000000 <7>[ 53.520273] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: EU type: simd16 <7>[ 53.520471] xe 0000:00:02.0: [drm:xe_gt_topology_init [xe]] Tile0: GT1: L3 bank mask: 00000000,0000000f <6>[ 53.520671] xe 0000:00:02.0: [drm] Tile0: GT1: vcs1 fused off <6>[ 53.520674] xe 0000:00:02.0: [drm] Tile0: GT1: vcs2 fused off <6>[ 53.520677] xe 0000:00:02.0: [drm] Tile0: GT1: vcs3 fused off <6>[ 53.520679] xe 0000:00:02.0: [drm] Tile0: GT1: vcs4 fused off <6>[ 53.520681] xe 0000:00:02.0: [drm] Tile0: GT1: vcs5 fused off <6>[ 53.520683] xe 0000:00:02.0: [drm] Tile0: GT1: vcs6 fused off <6>[ 53.520685] xe 0000:00:02.0: [drm] Tile0: GT1: vcs7 fused off <6>[ 53.520688] xe 0000:00:02.0: [drm] Tile0: GT1: vecs1 fused off <6>[ 53.520691] xe 0000:00:02.0: [drm] Tile0: GT1: vecs2 fused off <6>[ 53.520694] xe 0000:00:02.0: [drm] Tile0: GT1: vecs3 fused off <7>[ 53.520830] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT1: Add vcs0 whitelist to engine <7>[ 53.521256] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT1: Add vecs0 whitelist to engine <7>[ 53.521638] xe 0000:00:02.0: [drm:whitelist_apply_to_hwe [xe]] Tile0: GT1: Add gsccs0 whitelist to engine <7>[ 53.523679] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying GT save-restore MMIOs <7>[ 53.523985] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x4148] = 0x00000000 <7>[ 53.524248] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x82a8] = 0x00800000 <7>[ 53.524552] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb604] = 0x08104440 <7>[ 53.524784] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb608] = 0x30200000 <7>[ 53.525044] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb654] = 0x00020000 <7>[ 53.525246] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0xb658] = 0x0000007f <7>[ 53.525452] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c3f08] = 0x00000020 <7>[ 53.525636] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c3f10] = 0x00400000 <7>[ 53.525849] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c3f1c] = 0x00000008 <7>[ 53.526042] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: flag:0x1 <7>[ 53.526222] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: mocs entries: 16 <7>[ 53.526397] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[0] 0x4000 0xc <7>[ 53.526582] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[1] 0x4004 0x10c <7>[ 53.526749] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[2] 0x4008 0x130 <7>[ 53.526936] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[3] 0x400c 0x13c <7>[ 53.527126] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[4] 0x4010 0x100 <7>[ 53.527280] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[5] 0x4014 0x100 <7>[ 53.527432] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[6] 0x4018 0x100 <7>[ 53.527577] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[7] 0x401c 0x100 <7>[ 53.527723] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[8] 0x4020 0x100 <7>[ 53.527876] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[9] 0x4024 0x100 <7>[ 53.528014] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[10] 0x4028 0x100 <7>[ 53.528150] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[11] 0x402c 0x100 <7>[ 53.528278] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[12] 0x4030 0x100 <7>[ 53.528404] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[13] 0x4034 0x100 <7>[ 53.528526] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[14] 0x4038 0x100 <7>[ 53.528659] xe 0000:00:02.0: [drm:xe_mocs_init [xe]] Tile0: GT1: GLOB_MOCS[15] 0x403c 0x100 <7>[ 53.528796] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying vcs0 save-restore MMIOs <7>[ 53.528951] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c0050] = 0x10001000 <7>[ 53.529085] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c00d4] = 0xc000c000 <7>[ 53.529618] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying vecs0 save-restore MMIOs <7>[ 53.529766] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c8050] = 0x10001000 <7>[ 53.529907] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x1c80d4] = 0xc000c000 <7>[ 53.530380] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: Applying gsccs0 save-restore MMIOs <7>[ 53.530501] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x11a050] = 0x10001000 <7>[ 53.530617] xe 0000:00:02.0: [drm:xe_reg_sr_apply_mmio [xe]] Tile0: GT1: REG[0x11a0d4] = 0xc000c000 <7>[ 53.531225] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled <7>[ 53.531377] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 0] = 0x00df63f7 <7>[ 53.531483] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 1] = 0x00000000 <7>[ 53.531583] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 2] = 0x00000014 <7>[ 53.531679] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 3] = 0x00000001 <7>[ 53.531772] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 4] = 0x00001e16 <7>[ 53.531879] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 5] = 0x64a00004 <7>[ 53.531973] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 6] = 0x00000000 <7>[ 53.532065] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 7] = 0x00000000 <7>[ 53.532152] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 8] = 0x00000000 <7>[ 53.532236] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[ 9] = 0x00000000 <7>[ 53.532317] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[10] = 0x00000000 <7>[ 53.532395] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[11] = 0x00000000 <7>[ 53.532472] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[12] = 0x00000000 <7>[ 53.532548] xe 0000:00:02.0: [drm:guc_print_params [xe]] Tile0: GT1: GuC param[13] = 0x00000000 <7>[ 53.532647] xe 0000:00:02.0: [drm:xe_guc_id_mgr_init [xe]] Tile0: GT1: using 65535 GuC IDs <7>[ 53.532762] xe 0000:00:02.0: [drm:xe_guc_db_mgr_init [xe]] Tile0: GT1: using 256 doorbells <7>[ 53.534076] xe 0000:00:02.0: [drm:xe_guc_buf_cache_init [xe]] Tile0: GT1: reusable buffer with 2048 dwords at 0x1984000 for xe_guc_init_post_hwconfig [xe] <7>[ 53.563850] xe 0000:00:02.0: [drm:xe_guc_ads_populate [xe]] Tile0: GT1: Updated ADS capture size 24576 (was 45056) <7>[ 53.585183] xe 0000:00:02.0: [drm:guc_wait_ucode [xe]] Tile0: GT1: GuC load: init took 20ms, freq = 800MHz (req = 800MHz), before = 800MHz, status = 0x8002F034 <7>[ 53.585687] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled <7>[ 53.587091] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT1: LRC vcs0 WA job: 0 dwords <7>[ 53.587341] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT1: No non-register state to emit on graphics ver 20.04 <7>[ 53.590096] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT1: LRC vecs0 WA job: 0 dwords <7>[ 53.590381] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT1: No non-register state to emit on graphics ver 20.04 <7>[ 53.593747] xe 0000:00:02.0: [drm:xe_gt_record_default_lrcs [xe]] Tile0: GT1: LRC gsccs0 WA job: 0 dwords <7>[ 53.594049] xe 0000:00:02.0: [drm:xe_lrc_emit_hwe_state_instructions [xe]] Tile0: GT1: No non-register state to emit on graphics ver 20.04 <7>[ 53.636856] xe 0000:00:02.0: [drm:xe_huc_auth [xe]] Tile0: GT1: HuC: authenticated via GuC <7>[ 53.637521] xe 0000:00:02.0: [drm:xe_pagefault_init [xe]] xe_pagefault_entry_size=64, total_num_eus=56, pf_queue->size=65536 <7>[ 53.637811] xe 0000:00:02.0: [drm:xe_pagefault_init [xe]] xe_pagefault_entry_size=64, total_num_eus=56, pf_queue->size=65536 <7>[ 53.638146] xe 0000:00:02.0: [drm:xe_pagefault_init [xe]] xe_pagefault_entry_size=64, total_num_eus=56, pf_queue->size=65536 <7>[ 53.638419] xe 0000:00:02.0: [drm:xe_pagefault_init [xe]] xe_pagefault_entry_size=64, total_num_eus=56, pf_queue->size=65536 <7>[ 53.639103] xe 0000:00:02.0: [drm:xe_oa_print_gt_oa_units [xe]] Tile0: GT0: oa_unit 0, type 0, Engines: rcs0 ccs0 <7>[ 53.639365] xe 0000:00:02.0: [drm:xe_oa_print_gt_oa_units [xe]] Tile0: GT1: oa_unit 1, type 2, Engines: <7>[ 53.639615] xe 0000:00:02.0: [drm:xe_oa_print_gt_oa_units [xe]] Tile0: GT1: oa_unit 2, type 1, Engines: vcs0 vecs0 <7>[ 53.641455] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 0: start 0x90008 <7>[ 53.641825] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 1: start 0x90108 <7>[ 53.642181] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 2: start 0x90208 <7>[ 53.642582] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 3: start 0x90308 <7>[ 53.642933] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:88:pipe A] FQ 4: start 0x903c8 <7>[ 53.643271] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:146:pipe B] FQ 0: start 0x98008 <7>[ 53.643591] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:146:pipe B] FQ 1: start 0x98108 <7>[ 53.643949] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:146:pipe B] FQ 2: start 0x98208 <7>[ 53.644239] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:146:pipe B] FQ 3: start 0x98308 <7>[ 53.644525] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:146:pipe B] FQ 4: start 0x983c8 <7>[ 53.644807] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:204:pipe C] FQ 0: start 0x52008 <7>[ 53.645100] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:204:pipe C] FQ 1: start 0x52108 <7>[ 53.645398] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:204:pipe C] FQ 2: start 0x52208 <7>[ 53.645657] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:204:pipe C] FQ 3: start 0x52308 <7>[ 53.645938] xe 0000:00:02.0: [drm:intel_flipq_init [xe]] [CRTC:204:pipe C] FQ 4: start 0x523c8 <7>[ 53.646583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes <7>[ 53.646885] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:88:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1 <7>[ 53.647190] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:83:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45 <7>[ 53.647556] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:146:pipe B] enable: no [fastset] <7>[ 53.647898] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:204:pipe C] enable: no [fastset] <7>[ 53.649525] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: A) <7>[ 53.649810] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes) <7>[ 53.666513] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:146:pipe B] <7>[ 53.666928] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:204:pipe C] <7>[ 53.678097] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:208:eDP-1] adding connector to sysfs <7>[ 53.682734] xe 0000:00:02.0: [drm:intel_backlight_device_register [xe]] [CONNECTOR:208:eDP-1] backlight device intel_backlight registered <7>[ 53.683097] xe 0000:00:02.0: [drm:intel_panel_register [xe]] [CONNECTOR:208:eDP-1] Registered panel device 'card0-eDP-1', has fwnode: yes <7>[ 53.683396] xe 0000:00:02.0: [drm:intel_panel_register [xe]] [CONNECTOR:208:eDP-1] Panel prepare <7>[ 53.684286] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX A/DDI A/PHY A bus for card0-eDP-1 <7>[ 53.686687] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:208:eDP-1] generating connector hotplug event <7>[ 53.686802] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:217:DP-1] adding connector to sysfs <7>[ 53.687573] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX USBC1/DDI TC1/PHY TC1 bus for card0-DP-1 <7>[ 53.688558] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:217:DP-1] generating connector hotplug event <7>[ 53.688619] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:229:DP-2] adding connector to sysfs <7>[ 53.689377] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX USBC2/DDI TC2/PHY TC2 bus for card0-DP-2 <7>[ 53.690477] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:229:DP-2] generating connector hotplug event <7>[ 53.690521] xe 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:237:DP-3] adding connector to sysfs <7>[ 53.691026] xe 0000:00:02.0: [drm:intel_dp_connector_register [xe]] registering AUX USBC3/DDI TC3/PHY TC3 bus for card0-DP-3 <7>[ 53.691776] xe 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:237:DP-3] generating connector hotplug event <6>[ 53.691809] [drm] Initialized xe 1.1.0 for 0000:00:02.0 on minor 0 <7>[ 53.691869] xe 0000:00:02.0: [drm:intel_opregion_resume [xe]] 4 outputs detected <6>[ 53.704559] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6>[ 53.708516] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5 <7>[ 53.709850] xe 0000:00:02.0: [drm:intel_audio_init [xe]] use AUD_FREQ_CNTRL of 0x8010 (init value 0x8010) <7>[ 53.710013] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480 <7>[ 53.710793] check_position_fix: snd_hda_intel 0000:00:1f.3: Using SKL position fix <6>[ 53.710804] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <7>[ 53.712355] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] [PLANE:33:plane 1A] no fb, skipping <7>[ 53.712481] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] [CRTC:146:pipe B] not active, skipping <7>[ 53.712600] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] [CRTC:204:pipe C] not active, skipping <7>[ 53.712715] xe 0000:00:02.0: [drm:intel_fbdev_setup [xe]] no active fbs found, not using BIOS config <6>[ 53.713212] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops intel_audio_component_bind_ops [xe]) <7>[ 53.713254] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:217:DP-1] <7>[ 53.714753] xe 0000:00:02.0: [drm:drm_client_modeset_probe] <7>[ 53.714734] xe 0000:00:02.0: [drm:intel_audio_component_get_power [xe]] restored AUD_FREQ_CNTRL to 0x8010 <7>[ 53.715663] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 53.715857] xe 0000:00:02.0: [drm:intel_hotplug_detect_connector [xe]] [CONNECTOR:217:DP-1] status updated from unknown to disconnected (epoch counter 0->1) <7>[ 53.715995] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:229:DP-2] <7>[ 53.716152] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 53.716289] xe 0000:00:02.0: [drm:intel_hotplug_detect_connector [xe]] [CONNECTOR:229:DP-2] status updated from unknown to disconnected (epoch counter 0->1) <7>[ 53.716418] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:237:DP-3] <7>[ 53.716569] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 53.716696] xe 0000:00:02.0: [drm:intel_hotplug_detect_connector [xe]] [CONNECTOR:237:DP-3] status updated from unknown to disconnected (epoch counter 0->1) <7>[ 53.717126] xe 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event <7>[ 53.717270] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] <7>[ 53.717282] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:208:eDP-1] <7>[ 53.717919] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 53.718257] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7>[ 53.718422] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 53.718568] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 53.718808] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 53.718823] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 53.718826] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 53.718827] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7>[ 53.718831] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 53.718835] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 53.718838] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD monitor <5>[ 53.718843] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 53.718845] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD size 20, SAD count 0 <5>[ 53.718848] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 53.718876] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] VRR capable: yes <7>[ 53.719031] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7>[ 53.719167] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7>[ 53.719929] azx_first_init: snd_hda_intel 0000:00:1f.3: chipset global capabilities = 0x9b01 <7>[ 53.719994] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] status updated from unknown to connected <5>[ 53.720293] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 53.720296] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 53.720298] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 53.720362] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] probed modes: <7>[ 53.720370] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 53.720373] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 53.720378] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] <7>[ 53.720381] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:217:DP-1] <7>[ 53.720596] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] disconnected <7>[ 53.720600] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] <7>[ 53.720602] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:229:DP-2] <7>[ 53.720764] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] disconnected <7>[ 53.720767] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] <7>[ 53.720770] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:237:DP-3] <7>[ 53.720945] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] disconnected <7>[ 53.720948] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] enabled? yes <7>[ 53.720951] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:217:DP-1] enabled? no <7>[ 53.720953] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:229:DP-2] enabled? no <7>[ 53.720955] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:237:DP-3] enabled? no <7>[ 53.720989] azx_init_pci: snd_hda_intel 0000:00:1f.3: Clearing TCSEL <7>[ 53.720999] azx_init_pci: snd_hda_intel 0000:00:1f.3: SCH snoop: Enabled <7>[ 53.721082] xe 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7>[ 53.721415] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] found preferred mode: 2880x1800 <7>[ 53.721417] xe 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7>[ 53.721430] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:88:pipe A] desired mode 2880x1800 set (0,0) <7>[ 53.721564] xe 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <7>[ 53.721572] xe 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [xe]] no BIOS fb, allocating a new one <7>[ 53.721998] xe 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event <7>[ 53.729372] xe 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [xe]] allocated 2880x1800 fb: 0x01da5000 <6>[ 53.732184] fbcon: xedrmfb (fb0) is primary device <7>[ 53.736072] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:208:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7>[ 53.736346] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:207:DDI A/PHY A][CRTC:88:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000 <7>[ 53.736603] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000 <7>[ 53.736851] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:88:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7>[ 53.737080] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:207:DDI A/PHY A] [CRTC:88:pipe A] <7>[ 53.737301] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 8102230/8388608 link 675185/524288, found tu 64, data 6329869/8388608 link 421991/524288) <7>[ 53.737510] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in dpll_hw_state.cx0pll C10 <7>[ 53.737713] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] expected: <7>[ 53.737933] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_hw_state: fracen: yes, <7>[ 53.738131] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] quot: 40960, rem: 0, den: 1, <7>[ 53.738326] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] multiplier: 140, tx_clk_div: 1. <7>[ 53.738517] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_rawhw_state: <7>[ 53.738725] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] tx: 0x10, cmn: 0x21 <7>[ 53.738928] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[0] = 0xf4, pll[1] = 0x0, pll[2] = 0xf8, pll[3] = 0x0 <7>[ 53.739117] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7>[ 53.739300] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7>[ 53.739482] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[12] = 0xa0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7>[ 53.739662] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[16] = 0x84, pll[17] = 0x4f, pll[18] = 0xe5, pll[19] = 0x23 <7>[ 53.739849] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] found: <7>[ 53.740035] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_hw_state: fracen: no, <7>[ 53.740213] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] multiplier: 225, tx_clk_div: 1. <7>[ 53.740394] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] c10pll_rawhw_state: <7>[ 53.740571] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] tx: 0x10, cmn: 0x21 <7>[ 53.740746] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <7>[ 53.740941] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7>[ 53.741117] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7>[ 53.741291] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7>[ 53.741464] xe 0000:00:02.0: [drm:intel_cx0pll_dump_hw_state [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7>[ 53.741639] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 30) <7>[ 53.741833] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in port_clock (expected 270000, found 432000) <7>[ 53.742021] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:88:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0) <7>[ 53.742204] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:88:pipe A] fastset requirement not met, forcing full modeset <7>[ 53.742438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051 <7>[ 53.742643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm <7>[ 53.742812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7>[ 53.743597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 <7>[ 53.743759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 <6>[ 53.743996] xe 0000:00:02.0: [drm] Tile0: GT1: found GSC cv104.1.0 <7>[ 53.743930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 53.744086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.744243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.744409] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:43:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.744574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 53.744691] xe 0000:00:02.0: [drm:gsc_work [xe]] Tile0: GT1: GSC FW async load completed <7>[ 53.744730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.744891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.745040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:53:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.745210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 53.745349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.745495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.745634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.745792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 53.746010] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.746168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.746341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:73:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.746494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7>[ 53.746631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.746767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.746933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:83:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7>[ 53.747118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:88:pipe A] data rate 1390840 num active planes 1 <7>[ 53.747313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7>[ 53.747485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7>[ 53.747657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7>[ 53.747841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7>[ 53.748016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7>[ 53.748277] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:88:pipe A] enable: yes [modeset] <7>[ 53.748451] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7>[ 53.748624] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7>[ 53.748789] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <7>[ 53.748970] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: , slave transcoder bitmask = 0x0 <7>[ 53.749129] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7>[ 53.749286] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7>[ 53.749439] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7>[ 53.749597] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7>[ 53.749760] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7>[ 53.749921] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7>[ 53.750065] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled <7>[ 53.750206] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7>[ 53.750354] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7>[ 53.750502] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14 <7>[ 53.750643] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7>[ 53.750784] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7>[ 53.750935] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7>[ 53.751075] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7>[ 53.751228] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7>[ 53.751363] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7>[ 53.751509] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7>[ 53.751661] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97 <7>[ 53.751826] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906 <7>[ 53.751969] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 53.752112] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 53.752259] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 53.752411] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 53.752555] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7>[ 53.752700] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7>[ 53.752857] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7>[ 53.752997] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7>[ 53.753127] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7>[ 53.753256] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7>[ 53.753384] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dpll_hw_state: dpll: 0x69780, dpll_md: 0x42110, fp0: 0x1a2, fp1: 0x1000000 <7>[ 53.753511] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7>[ 53.753636] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7>[ 53.753761] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 53.753900] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.754024] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.754141] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.754260] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 53.754378] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7>[ 53.754493] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.754606] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.754719] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7>[ 53.754841] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7>[ 53.754949] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7>[ 53.755056] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:209] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7>[ 53.755164] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7>[ 53.755260] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0 <7>[ 53.755356] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:43:plane 2A] fb: [NOFB], visible: no <7>[ 53.755451] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:53:plane 3A] fb: [NOFB], visible: no <7>[ 53.755550] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 4A] fb: [NOFB], visible: no <7>[ 53.755654] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:73:plane 5A] fb: [NOFB], visible: no <7>[ 53.755757] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:83:cursor A] fb: [NOFB], visible: no <7>[ 53.767743] xe 0000:00:02.0: [drm:xe_huc_auth [xe]] Tile0: GT1: HuC: authenticated via GSC <7>[ 53.767730] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 53.768024] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 53.768162] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 53.768291] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port A <7>[ 53.768419] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 53.768541] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 53.768660] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 53.768777] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port B <7>[ 53.768901] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 53.769018] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 53.769134] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 53.769246] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port C <7>[ 53.769356] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 53.769465] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 53.769574] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 53.769684] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port D <7>[ 53.769794] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 53.769928] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 53.770044] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 53.770154] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port E <7>[ 53.770260] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 53.770365] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 53.770470] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 53.770575] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port F <7>[ 53.770681] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 53.770790] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 53.770906] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 53.771019] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port G <7>[ 53.771127] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 53.771234] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 53.771341] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 53.771446] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port H <7>[ 53.771553] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 53.771659] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 53.771767] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 53.771881] xe 0000:00:02.0: [drm:intel_audio_component_get_eld [xe]] Not valid for port I <7>[ 53.776454] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM <7>[ 53.776618] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]] <6>[ 53.779996] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input6 <6>[ 53.781806] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input7 <6>[ 53.782628] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input8 <6>[ 53.784056] input: HDA Intel PCH HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input9 <7>[ 53.983057] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:208:eDP-1] set backlight PWM = 0 <7>[ 53.984349] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A <7>[ 54.004772] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turn panel power off <7>[ 54.005198] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power off time <7>[ 54.005196] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000 <7>[ 54.005577] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7>[ 54.005651] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:207:DDI A/PHY A] - short <7>[ 54.057877] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000 <7>[ 54.058260] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:207:DDI A/PHY A] - short <7>[ 54.063864] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7>[ 54.064292] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A <7>[ 54.064274] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:207:DDI A/PHY A] <7>[ 54.065116] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0xffff0072 0x1341b072) <7>[ 54.065113] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:207:DDI A/PHY A] <7>[ 54.065453] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:207:DDI A/PHY A] <7>[ 54.065773] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:216:DDI TC1/PHY TC1] <7>[ 54.066101] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:218:DP-MST A] <7>[ 54.066381] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:219:DP-MST B] <7>[ 54.066667] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:220:DP-MST C] <7>[ 54.066971] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:228:DDI TC2/PHY TC2] <7>[ 54.067266] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:230:DP-MST A] <7>[ 54.067548] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:231:DP-MST B] <7>[ 54.067841] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:232:DP-MST C] <7>[ 54.068152] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:236:DDI TC3/PHY TC3] <7>[ 54.068410] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:238:DP-MST A] <7>[ 54.068665] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:239:DP-MST B] <7>[ 54.068943] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:240:DP-MST C] <7>[ 54.069246] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A <7>[ 54.070946] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turn panel power on <7>[ 54.071285] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power cycle (493 ms remaining) <7>[ 54.091223] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7>[ 54.091604] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:207:DDI A/PHY A] - long <7>[ 54.091951] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10 <7>[ 54.092300] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:207:DDI A/PHY A] <7>[ 54.175666] xe 0000:00:02.0: [drm:gsc_work [xe]] Tile0: GT1: GSC proxy init completed <7>[ 54.567054] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060 <7>[ 54.577571] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7>[ 54.578058] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 wait for panel power on <7>[ 54.578509] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063 <7>[ 54.614878] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7>[ 54.615308] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:207:DDI A/PHY A] - long <7>[ 54.615666] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20 <7>[ 54.616132] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:207:DDI A/PHY A] <7>[ 54.735454] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 54.735454] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 54.735525] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 54.787448] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7>[ 54.789548] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turning VDD on <7>[ 54.789897] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7>[ 54.792036] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80 <7>[ 54.793254] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Reloading eDP link rates <7>[ 54.794054] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05 <7>[ 54.795089] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7>[ 54.796135] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7>[ 54.797069] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Clock recovery OK <7>[ 54.797343] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Using DP training pattern TPS4 <7>[ 54.798632] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7>[ 54.798943] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:208:eDP-1][ENCODER:207:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4 <7>[ 54.799699] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A <7>[ 54.800149] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]] <7>[ 54.800477] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A <7>[ 54.800801] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:208:eDP-1] set backlight PWM = 192000 <7>[ 54.817145] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2 <7>[ 54.819023] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:208:eDP-1] <7>[ 54.819419] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:88:pipe A] <7>[ 54.820775] xe 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [xe]] pipe has 30 bpp for eDP panel, overriding BIOS-provided max 24 bpp <7>[ 54.822098] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800071 0xc01b072) <7>[ 54.823118] xe 0000:00:02.0: [drm:intel_backlight_device_update_status [xe]] updating intel_backlight, brightness=9600/192000 <7>[ 54.823500] xe 0000:00:02.0: [drm:intel_panel_actually_set_backlight [xe]] [CONNECTOR:208:eDP-1] set backlight level = 13892 <6>[ 54.823794] Console: switching to colour frame buffer device 180x56 <6>[ 54.858191] xe 0000:00:02.0: [drm] fb0: xedrmfb frame buffer device <7>[ 54.873909] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: display version: 20 <7>[ 54.874365] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: display stepping: B0 <7>[ 54.874756] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: cursor_needs_physical: no <7>[ 54.875350] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_cdclk_crawl: yes <7>[ 54.875739] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_cdclk_squash: yes <7>[ 54.876191] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_ddi: yes <7>[ 54.876648] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dp_mst: yes <7>[ 54.877110] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dsb: yes <7>[ 54.877496] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_fpga_dbg: yes <7>[ 54.877994] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_gmch: no <7>[ 54.878375] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_hotplug: yes <7>[ 54.878751] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_hti: no <7>[ 54.879181] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_ipc: yes <7>[ 54.879571] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_overlay: no <7>[ 54.879980] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_psr: yes <7>[ 54.880345] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_psr_hw_tracking: no <7>[ 54.880762] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: overlay_needs_physical: no <7>[ 54.881238] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: supports_tv: no <7>[ 54.881597] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_hdcp: yes <7>[ 54.882035] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dmc: yes <7>[ 54.882387] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: has_dsc: yes <7>[ 54.882732] xe 0000:00:02.0: [drm:intel_display_driver_register [xe]] i915 display info: rawclk rate: 38400 kHz <7>[ 54.884432] [drm:intel_dsm_detect.isra.0 [xe]] no _DSM method for intel device <7>[ 54.884813] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PICA_TC <7>[ 54.885391] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_D <7>[ 54.885844] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_C <7>[ 54.886296] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_B <7>[ 54.892679] xe 0000:00:02.0: [drm:xe_pci_probe [xe]] d3cold: capable=no <7>[ 54.900369] xe 0000:00:02.0: [drm:drm_fb_helper_hotplug_event] <7>[ 54.900408] xe 0000:00:02.0: [drm:drm_client_modeset_probe] <7>[ 54.901186] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] <7>[ 54.901217] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:208:eDP-1] <7>[ 54.903590] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 54.903626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 54.904261] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 54.905226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 54.906834] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7>[ 54.907234] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 54.907598] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 54.908295] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 54.908308] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 54.908312] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.908313] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7>[ 54.908320] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 54.908325] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.908328] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD monitor <5>[ 54.908345] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.908348] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD size 20, SAD count 0 <5>[ 54.908353] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.908392] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] VRR capable: yes <7>[ 54.908632] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7>[ 54.908866] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5>[ 54.909645] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 54.909648] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 54.909651] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.909763] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] probed modes: <7>[ 54.909778] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 54.909784] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 54.909791] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] <7>[ 54.909797] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:217:DP-1] <7>[ 54.910622] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 54.910993] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] disconnected <7>[ 54.911003] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] <7>[ 54.911012] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:229:DP-2] <7>[ 54.911284] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 54.911453] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] disconnected <7>[ 54.911457] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] <7>[ 54.911461] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:237:DP-3] <7>[ 54.911660] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7>[ 54.911824] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] disconnected <7>[ 54.911828] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] enabled? yes <7>[ 54.911833] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:217:DP-1] enabled? no <7>[ 54.911836] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:229:DP-2] enabled? no <7>[ 54.911839] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:237:DP-3] enabled? no <7>[ 54.911988] xe 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7>[ 54.912019] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] found preferred mode: 2880x1800 <7>[ 54.912023] xe 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 2880x1800 config <7>[ 54.912074] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:88:pipe A] desired mode 2880x1800 set (0,0) <7>[ 54.913634] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 54.913832] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7>[ 54.917475] xe 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0 <7>[ 54.917624] xe 0000:00:02.0: [drm:drm_fb_helper_hotplug_event] <7>[ 54.917642] xe 0000:00:02.0: [drm:drm_client_modeset_probe] <7>[ 54.918051] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] <7>[ 54.918062] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:208:eDP-1] <7>[ 54.918704] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7>[ 54.919104] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7>[ 54.919472] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 54.919807] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7>[ 54.920371] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5>[ 54.920384] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 54.920390] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.920395] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7>[ 54.920406] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5>[ 54.920416] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.920423] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD monitor <5>[ 54.920442] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.920446] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:208:eDP-1] ELD size 20, SAD count 0 <5>[ 54.920457] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.920509] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] VRR capable: yes <7>[ 54.920794] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7>[ 54.921087] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:208:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5>[ 54.922031] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 54.922038] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5>[ 54.922043] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7>[ 54.922176] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:208:eDP-1] probed modes: <7>[ 54.922193] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7>[ 54.922202] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7>[ 54.922211] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] <7>[ 54.922219] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:217:DP-1] <7>[ 54.922600] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:217:DP-1] disconnected <7>[ 54.922609] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] <7>[ 54.922616] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:229:DP-2] <7>[ 54.922966] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:229:DP-2] disconnected <7>[ 54.922975] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] <7>[ 54.922981] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:237:DP-3] <7>[ 54.923218] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:237:DP-3] disconnected <7>[ 54.923221] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] enabled? yes <7>[ 54.923224] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:217:DP-1] enabled? no <7>[ 54.923227] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:229:DP-2] enabled? no <7>[ 54.923229] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:237:DP-3] enabled? no <7>[ 54.923344] xe 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7>[ 54.923362] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:208:eDP-1] found preferred mode: 2880x1800 <7>[ 54.923365] xe 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 2880x1800 config <7>[ 54.923394] xe 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:88:pipe A] desired mode 2880x1800 set (0,0) <7>[ 54.934345] xe 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0 <7>[ 54.936202] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 54.936575] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 54.937025] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 54.952876] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7>[ 54.954919] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7>[ 54.984875] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7>[ 54.985196] [IGT] xe_module_load: finished subtest load, SUCCESS <7>[ 54.985748] [IGT] xe_module_load: exiting, ret=0 <7>[ 55.000861] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7>[ 55.001199] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7>[ 55.001459] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7>[ 55.036529] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_2 <7>[ 55.976111] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 55.976194] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 55.976316] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7>[ 57.506527] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 turning VDD off <7>[ 57.506919] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:207:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067