Result:
i915_display_info16 igt_runner16 results16.json results16-xe-load.json guc_logs16.tar i915_display_info_post_exec16 boot16 dmesg16
| Detail | Value |
|---|---|
| Duration | 4.83 seconds |
| Hostname |
shard-lnl-4 |
| Igt-Version |
IGT-Version: 2.4-g02b0e01dd (x86_64) (Linux: 7.1.0-rc1-lgci-xe-xe-4951-bc5111f7a4ab2ac93-debug+ x86_64) |
| Out |
Using IGT_SRANDOM=1777521719 for randomisation Opened device: /dev/dri/card0 FBC last action not supported Can't test DRRS: Not supported. Starting subtest: plane-fbc-rte FBC is not enabled: FBC disabled: disabled per module param or by default [PLANE:35:plane 1A]: plane not visible [PLANE:65:plane 2A]: plane not Testing fbc on plane 1A Testing fbc on plane 2A Testing fbc on plane 3A Subtest plane-fbc-rte: SUCCESS (4.831s) |
| Err |
Starting subtest: plane-fbc-rte Subtest plane-fbc-rte: SUCCESS (4.831s) |
| Dmesg |
<6> [94.292691] Console: switching to colour dummy device 80x25
<6> [94.292834] [IGT] kms_frontbuffer_tracking: executing
<7> [94.300341] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [94.300352] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [94.300605] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [94.300998] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [94.301002] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [94.301208] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [94.301566] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [94.301570] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [94.301754] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<7> [94.302081] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1]
<7> [94.302086] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:393:eDP-1]
<7> [94.302798] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [94.303188] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [94.303650] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [94.304016] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [94.304234] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [94.304242] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [94.304245] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [94.304247] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [94.304251] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [94.304256] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [94.304258] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD monitor
<5> [94.304262] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [94.304264] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD size 20, SAD count 0
<5> [94.304268] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [94.304287] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] VRR capable: yes
<7> [94.304546] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [94.304685] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [94.305064] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [94.305068] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [94.305070] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [94.305137] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1] probed modes:
<7> [94.305142] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [94.305148] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [94.305168] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [94.305173] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [94.305341] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [94.305353] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [94.305357] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [94.305533] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [94.305545] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [94.305549] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [94.305708] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<7> [94.307521] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [94.307719] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [94.307886] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]
<7> [94.308072] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435]
<7> [94.308764] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436]
<6> [94.309397] [IGT] kms_frontbuffer_tracking: starting subtest plane-fbc-rte
<7> [94.309778] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to f
<7> [94.309874] xe 0000:00:02.0: [drm:intel_psr_debug_set [xe]] Invalid debug mask f
<7> [94.309982] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to 1
<7> [94.310132] xe 0000:00:02.0: [drm:compute_baseline_pipe_bpp [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [94.310241] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [94.310337] xe 0000:00:02.0: [drm:intel_dp_compute_output_format [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [94.310443] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [94.310535] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [94.310647] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A]
<7> [94.310779] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [fastset]
<7> [94.310892] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [94.311003] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [94.311104] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [94.311196] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [94.311288] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [94.311378] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [94.311488] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [94.311586] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [94.311672] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [94.311749] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [94.311826] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [94.311903] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum hblank: 0
<7> [94.311979] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [94.312055] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [94.312131] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [94.312206] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [94.312281] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [94.312355] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [94.312440] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [94.312532] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [94.312628] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [94.312709] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [94.312785] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [94.312861] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pixel rate 347710, min cdclk 173855, min voltage level 0
<7> [94.312936] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [94.313011] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0, sharpness_strength: 0
<7> [94.313086] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe src: 2880x1800+0+0
<7> [94.313161] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [94.313237] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [94.313313] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [94.313392] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [94.313470] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [94.313560] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [94.313641] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [94.313716] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [94.313790] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [94.313864] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [94.313939] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [94.314013] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [94.314089] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [94.314167] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [94.314243] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [94.314320] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [94.314401] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.314483] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.314581] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.314668] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [94.314747] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [94.314822] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.314897] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.314971] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.315051] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [94.315131] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [FB:394] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [94.315214] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [94.315294] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [94.315391] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [94.315481] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [94.315613] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [94.346422] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [94.346636] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [94.350970] xe 0000:00:02.0: [drm:intel_dp_dump_link_status [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] ln0_1:0x77 ln2_3:0x77 align:0x80 sink:0x1 adj_req0_1:0x0 adj_req2_3:0x0
<7> [94.351246] xe 0000:00:02.0: [drm:intel_dp_needs_link_retrain [xe]] [ENCODER:392:DDI A/PHY A] 8b/10b link not ok, retraining
<7> [94.354547] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [94.354708] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [94.354880] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]
<7> [94.355049] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435]
<7> [94.355733] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436]
<7> [94.462972] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [94.463194] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [94.463734] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [94.464134] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [94.464552] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [94.464916] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [94.465323] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [94.465767] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [94.466117] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [94.466512] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [94.466848] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [94.467227] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [94.467607] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [94.467933] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [94.468350] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [94.468713] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [94.469031] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [94.469361] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [94.469678] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [94.470046] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [94.470388] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [94.470702] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [94.471014] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [94.471340] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [94.471653] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [94.471954] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [94.472236] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [94.472573] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [94.472925] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [94.473272] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [94.473766] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [94.474060] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [94.474390] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [94.474656] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [94.474902] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [94.475143] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [94.475445] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [94.475677] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [94.475893] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [94.476108] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [94.476329] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:151:pipe A] releasing DPLL 0
<7> [94.476648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [94.476816] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [94.477004] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [94.477153] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [94.477307] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [94.477447] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [94.477587] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [94.477739] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [94.477916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [94.478116] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [94.478317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [94.478497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [94.478673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [94.478841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [94.479007] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [94.479194] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [94.479398] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [94.479570] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [94.479717] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [94.479894] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: no [modeset]
<7> [94.480052] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [NOFB], visible: no
<7> [94.480187] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [94.480334] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [94.480468] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [94.480451] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [94.480603] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [94.480645] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [94.480731] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [94.480793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [94.480958] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [94.481108] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [94.481467] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [94.481649] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [94.684368] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 0
<7> [94.685032] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [94.696700] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power off
<7> [94.697201] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [94.697279] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [94.697698] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [94.697731] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [94.749875] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [94.750269] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [94.757306] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [94.757782] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:151:pipe A]
<7> [94.757941] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [94.758567] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [94.759404] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [94.759981] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [94.760565] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [94.760932] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [94.761363] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [94.761722] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [94.762084] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [94.762486] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [94.762865] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [94.763185] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [94.763483] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [94.763774] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [94.764109] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [94.764455] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [94.764744] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [94.765028] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [94.765450] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [94.765745] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [94.766016] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [94.766563] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [94.766998] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xaa000000)
<7> [94.767574] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [94.767938] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [94.768372] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [94.768647] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [94.773476] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:270:pipe B]
<7> [94.776290] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:389:pipe C]
<7> [94.779048] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:429]
<7> [94.785223] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [94.785329] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [94.785410] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [94.785494] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [94.794815] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [94.794838] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:393:eDP-1]
<7> [94.794891] xe 0000:00:02.0: [drm:compute_baseline_pipe_bpp [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [94.795005] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [94.795116] xe 0000:00:02.0: [drm:intel_dp_compute_output_format [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [94.795206] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [94.795289] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [94.795380] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A]
<7> [94.795472] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [94.795560] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [94.795648] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [94.795735] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [94.795821] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [94.795906] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [94.795991] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [94.796075] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [94.796178] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [94.796193] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [94.796266] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [94.796348] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [94.796382] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [94.796430] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [94.796513] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [94.796508] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [94.796597] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [94.796680] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [94.796761] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [94.796841] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [94.796920] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [94.796998] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [94.797076] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [94.797162] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [94.797239] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [94.797315] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [94.797390] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [94.797465] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [94.797540] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [94.797615] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [94.797690] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [94.797764] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [94.797838] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [94.797912] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [94.797986] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [94.798059] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [94.798142] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [94.798217] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [94.798291] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [94.798364] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [94.798438] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [94.798511] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [94.798618] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [94.798685] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [94.798761] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [94.798820] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [94.798876] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [94.798931] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [94.798987] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [94.799041] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [94.799117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 1
<7> [94.799200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [94.799281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [94.799362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [94.799441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [94.799520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [94.799599] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [94.799697] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [94.799783] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [94.799871] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [94.799959] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [94.800063] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:151:pipe A] allocated DPLL 0
<7> [94.800150] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:151:pipe A] reserving DPLL 0
<7> [94.800230] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [modeset]
<7> [94.800314] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [94.800400] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [94.800481] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [94.800561] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [94.800643] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [94.800722] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [94.800799] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [94.800877] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [94.800952] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [94.801027] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [94.801106] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [94.801181] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum hblank: 0
<7> [94.801259] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [94.801334] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [94.801407] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [94.801480] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [94.801554] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [94.801626] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [94.801698] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [94.801771] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [94.801843] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [94.801915] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [94.801987] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [94.802058] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pixel rate 347710, min cdclk 173855, min voltage level 0
<7> [94.802141] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [94.802214] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0, sharpness_strength: 0
<7> [94.802287] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe src: 2880x1800+0+0
<7> [94.802360] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [94.802432] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [94.802503] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [94.802574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [94.802646] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [94.802716] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [94.802788] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [94.802858] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [94.802929] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [94.803000] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [94.803070] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [94.803154] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [94.803230] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [94.803308] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [94.803382] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [94.803456] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [94.803528] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.803600] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.803672] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.803750] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [94.803821] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [94.803892] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.803963] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.804034] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [94.804110] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [94.804182] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [FB:429] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x100000000000001, visible: yes
<7> [94.804257] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [94.804332] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [94.804407] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [94.804480] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [94.804553] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [94.804624] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [94.804695] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [94.805046] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [94.805300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [94.805433] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [94.805574] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [94.805676] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [94.805770] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [94.805857] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [94.805943] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [94.806013] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [94.806081] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [94.806163] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [94.806233] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [94.806302] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [94.806366] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [94.806429] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [94.806491] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [94.806554] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [94.806615] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [94.806680] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [94.806743] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [94.806828] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [94.806985] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [94.807048] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [94.807162] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [94.808293] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:151:pipe A]
<7> [94.808440] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [94.810450] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power on
<7> [94.810542] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power cycle (448 ms remaining)
<7> [95.260045] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [95.280676] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [95.281157] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power on
<7> [95.281514] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [95.317580] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [95.317968] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [95.318322] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [95.318753] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [95.347892] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [95.347878] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [95.347879] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [95.495809] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [95.496258] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7> [95.496609] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [95.498825] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [95.500383] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [95.501285] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [95.502602] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [95.504124] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [95.505361] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Clock recovery OK
<7> [95.505851] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [95.507408] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [95.507826] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [95.508657] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [95.509310] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [95.509744] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [95.510210] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 13892
<7> [95.526776] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [95.527304] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [95.531465] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [95.560843] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [95.561437] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [95.561982] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [95.593649] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [95.594057] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [95.610098] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:429] from all active usage due to RMFB ioctl
<7> [95.610172] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:35:plane 1A] because [FB:429] is removed
<7> [95.610250] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [95.610466] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [95.610620] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [95.610810] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [95.610946] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [95.611125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [95.611318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [95.611504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [95.611687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [95.611855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [95.612021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [95.726457] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [95.726748] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [95.727271] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [95.727792] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [95.728245] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [95.728686] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [95.729117] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [95.729661] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [95.730100] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [95.730509] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [95.730988] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [95.731405] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [95.731893] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [95.732308] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [95.732796] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [95.733270] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [95.733709] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [95.734100] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [95.734518] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [95.734958] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [95.735389] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [95.735933] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [95.736315] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [95.736876] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [95.737280] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [95.737655] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [95.738021] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [95.738377] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [95.738745] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [95.739069] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [95.739370] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [95.739701] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [95.739984] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [95.740259] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [95.740526] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [95.740819] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [95.741085] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [95.741320] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [95.741557] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [95.741857] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [95.742088] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:151:pipe A] releasing DPLL 0
<7> [95.742376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [95.742553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [95.742793] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [95.742949] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [95.743163] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [95.743370] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [95.743565] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [95.743810] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [95.743855] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: no [modeset]
<7> [95.744073] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [NOFB], visible: no
<7> [95.744075] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [95.744252] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [95.744277] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [95.744417] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [95.744587] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [95.744771] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [95.744945] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [95.745157] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [95.745330] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [95.745611] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [95.745758] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [95.947561] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 0
<7> [95.948249] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [95.959885] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power off
<7> [95.960337] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [95.960387] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [95.960800] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [95.960903] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [96.012899] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [96.013329] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [96.021237] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [96.021783] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:151:pipe A]
<7> [96.021893] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [96.022508] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [96.023398] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [96.024024] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [96.024643] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [96.025040] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [96.025372] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [96.025749] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [96.026109] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [96.026475] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [96.026862] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [96.027234] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [96.027629] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [96.027969] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [96.028304] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [96.028645] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [96.028944] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [96.029271] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [96.029732] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [96.030042] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [96.030323] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [96.030863] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [96.031356] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xaa000000)
<7> [96.031941] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [96.032360] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [96.032840] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [96.033171] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [96.038079] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:270:pipe B]
<7> [96.041001] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:389:pipe C]
<7> [96.048194] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [96.048410] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [96.048603] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [96.048792] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [96.060479] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [96.060916] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [96.061262] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [96.061654] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [98.145119] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]
<7> [98.166232] xe 0000:00:02.0: [drm:compute_baseline_pipe_bpp [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [98.167012] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [98.167666] xe 0000:00:02.0: [drm:intel_dp_compute_output_format [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [98.168228] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [98.168790] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [98.169349] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A]
<7> [98.169937] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [98.170485] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [98.171004] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [98.171608] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [98.172150] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [98.172641] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [98.173114] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [98.173586] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [98.174038] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [98.174631] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [98.175069] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [98.175534] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [98.176019] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [98.176501] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [98.176894] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [98.177275] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [98.177681] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [98.178067] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [98.178466] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [98.178777] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [98.179077] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [98.179360] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [98.179631] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [98.179924] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [98.180173] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [98.180429] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [98.180661] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [98.180875] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [98.181090] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [98.181295] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [98.181545] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [98.181736] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [98.181927] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [98.182113] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [98.182332] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [98.182518] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [98.182686] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [98.182877] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [98.183044] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [98.183282] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [98.183435] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [98.183714] xe 0000:00:02.0: [drm:compute_baseline_pipe_bpp [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [98.183886] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [98.184042] xe 0000:00:02.0: [drm:intel_dp_compute_output_format [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [98.184191] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [98.184312] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [98.184483] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A]
<7> [98.184621] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [98.184752] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [98.184877] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [98.185002] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [98.185123] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [98.185240] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [98.185362] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [98.185472] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [98.185579] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [98.185682] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [98.185785] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [98.185885] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [98.185985] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [98.186084] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [98.186179] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [98.186275] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [98.186383] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [98.186481] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [98.186576] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [98.186667] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [98.186751] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [98.186834] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [98.186917] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [98.187001] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [98.187081] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [98.187158] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [98.187234] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [98.187308] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [98.187414] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [98.187507] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [98.187610] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [98.187694] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [98.187770] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [98.187841] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [98.187911] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [98.187983] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [98.188055] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [98.188125] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [98.188197] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [98.188280] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [98.188362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [98.188477] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [98.188565] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [98.188641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [98.188702] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [98.188758] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [98.188813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [98.188888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 1
<7> [98.188983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [98.189077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [98.189162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [98.189242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [98.189329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [98.189433] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [98.189560] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [98.189664] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [98.189747] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [98.189850] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:151:pipe A] allocated DPLL 0
<7> [98.189927] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:151:pipe A] reserving DPLL 0
<7> [98.190010] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [modeset]
<7> [98.190095] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [98.190176] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [98.190258] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [98.190346] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [98.190450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [98.190554] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [98.190654] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [98.190734] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [98.190813] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [98.190891] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [98.190969] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [98.191047] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum hblank: 0
<7> [98.191124] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [98.191203] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [98.191279] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [98.191373] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [98.191473] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [98.191570] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [98.191665] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [98.191746] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [98.191822] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [98.191899] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [98.191974] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [98.192050] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pixel rate 347710, min cdclk 173855, min voltage level 0
<7> [98.192125] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [98.192199] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0, sharpness_strength: 0
<7> [98.192274] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe src: 2880x1800+0+0
<7> [98.192360] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [98.192458] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [98.192554] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [98.192648] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [98.192726] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [98.192803] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [98.192880] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [98.192955] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [98.193030] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [98.193105] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [98.193180] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [98.193256] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [98.193338] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [98.193447] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [98.193553] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [98.193641] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [98.193716] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [98.193790] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [98.193864] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [98.193937] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [98.194010] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [98.194084] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [98.194157] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [98.194229] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [98.194301] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [98.194406] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [FB:438] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x100000000000001, visible: yes
<7> [98.194502] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [98.194597] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [98.194682] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [98.194761] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [98.194834] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [98.194906] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [98.194978] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [98.195339] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [98.195463] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [98.195725] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [98.195860] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [98.196002] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [98.196100] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [98.196197] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [98.196285] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [98.196394] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [98.196485] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [98.196573] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [98.196655] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [98.196727] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [98.196791] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [98.196857] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [98.196921] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [98.196984] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [98.197046] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [98.197111] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [98.197176] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [98.197239] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [98.197330] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [98.197518] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [98.197598] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [98.197716] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [98.199046] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:151:pipe A]
<7> [98.199137] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [98.201161] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power on
<7> [98.201239] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [98.201351] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [98.211359] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [98.211455] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power on
<7> [98.211565] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [98.247888] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [98.248166] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [98.248401] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [98.248692] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [98.424737] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [98.425390] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7> [98.425928] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [98.428409] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [98.430122] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [98.431096] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [98.432367] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [98.433890] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [98.435254] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Clock recovery OK
<7> [98.435717] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [98.437420] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [98.437866] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [98.438705] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [98.439322] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [98.439780] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [98.440308] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 13892
<7> [98.443218] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 14745600 bytes of contiguous stolen space for FBC, limit: 2
<7> [98.443622] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:35:plane 1A]
<7> [98.456579] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [98.457315] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [98.461680] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [98.490266] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [98.490995] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [98.491711] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [98.524120] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [98.524703] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [98.543193] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [98.573222] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [98.573864] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [98.574506] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [98.607361] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [98.607793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [98.623787] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:438] from all active usage due to RMFB ioctl
<7> [98.623882] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:35:plane 1A] because [FB:438] is removed
<7> [98.623990] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [98.624515] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [98.624898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [98.625394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [98.625863] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [98.626411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [98.627013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [98.627741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [98.628412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [98.628997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [98.629709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [98.639366] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:35:plane 1A]
<7> [98.658964] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]
<7> [98.674130] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [98.674729] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [98.675277] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [98.678042] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [98.678492] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [98.678758] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [98.679008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [98.679351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [98.679623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 1
<7> [98.679958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [98.680311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [98.680593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [98.680860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [98.681133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [98.682186] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [98.682415] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [98.683250] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 14745600 bytes of contiguous stolen space for FBC, limit: 2
<7> [98.683431] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]
<7> [98.689937] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [98.723249] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [98.723893] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [98.724557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [98.757258] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [98.757692] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [98.775931] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [98.807103] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [98.807678] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [98.808222] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [98.840562] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [98.840969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [98.857097] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:438] from all active usage due to RMFB ioctl
<7> [98.857204] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:65:plane 2A] because [FB:438] is removed
<7> [98.857323] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [98.857741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [98.858205] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [98.858619] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [98.859062] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [98.859509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [98.860112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [98.860638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [98.861166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [98.861702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [98.862336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [98.872682] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]
<7> [98.892186] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]
<7> [98.909056] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [98.909593] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [98.910032] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [98.914615] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:95:plane 3A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [98.914934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [98.915307] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [98.915585] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [98.915846] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [98.916253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 1
<7> [98.916824] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:95:plane 3A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [98.917153] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [98.917454] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [98.917751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [98.918131] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [98.918476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 1
<7> [98.918960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [98.919505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [98.920082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [98.920642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [98.921222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [98.924247] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [98.924648] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [98.925799] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 14745600 bytes of contiguous stolen space for FBC, limit: 2
<7> [98.926197] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:95:plane 3A]
<7> [98.939857] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [98.974019] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [98.974680] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [98.975305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [99.007459] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [99.008128] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [99.026155] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [99.056983] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [99.057555] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [99.058115] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [99.090594] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [99.091086] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [99.107275] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:438] from all active usage due to RMFB ioctl
<7> [99.107423] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:95:plane 3A] because [FB:438] is removed
<7> [99.107580] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:95:plane 3A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [99.108196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [99.108635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [99.109156] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [99.109509] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [99.109932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [99.110500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [99.111026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [99.111530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [99.112090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [99.112567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [99.122640] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:95:plane 3A]
<6> [99.141001] [IGT] kms_frontbuffer_tracking: finished subtest plane-fbc-rte, SUCCESS
<7> [99.155238] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [99.155596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [99.155920] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [99.156159] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [99.156436] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [99.156698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 1
<7> [99.157036] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [99.157247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [99.157393] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [99.157541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [99.157652] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [99.157786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [99.158041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [99.158266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [99.160130] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [99.160445] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [99.162455] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 11059200 bytes of contiguous stolen space for FBC, limit: 2
<7> [99.162633] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:35:plane 1A]
<7> [99.172733] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [99.173623] [IGT] kms_frontbuffer_tracking: exiting, ret=0
<7> [99.173994] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to 0
<7> [99.174485] xe 0000:00:02.0: [drm:compute_baseline_pipe_bpp [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [99.174812] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [99.175164] xe 0000:00:02.0: [drm:intel_dp_compute_output_format [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [99.175441] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [99.175768] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A]
<7> [99.176122] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [fastset]
<7> [99.176395] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [99.176613] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [99.176824] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [99.177059] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [99.177257] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [99.177445] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [99.177630] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [99.177805] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [99.177998] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [99.178170] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [99.178336] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [99.178496] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum hblank: 0
<7> [99.178680] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [99.178832] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [99.179006] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [99.179155] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [99.179296] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [99.179434] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [99.179569] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [99.179701] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [99.179830] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [99.179982] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [99.180117] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [99.180243] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [99.180369] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [99.180494] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [99.180615] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [99.180727] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [99.180839] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [99.181054] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pixel rate 347710, min cdclk 173855, min voltage level 0
<7> [99.181165] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [99.181270] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0, sharpness_strength: 0
<7> [99.181370] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe src: 2880x1800+0+0
<7> [99.181468] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [99.181563] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [99.181654] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [99.181744] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [99.181833] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [99.181947] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [99.182046] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [99.182141] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [99.182225] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [99.182305] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [99.182385] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [99.182464] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [99.182540] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [99.182617] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [99.182693] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [99.182768] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [99.182844] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [99.183100] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [99.183192] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [99.183266] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [99.183338] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [99.183411] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [99.183486] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [99.183561] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [99.183633] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [99.183705] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [FB:394] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [99.183779] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [99.183857] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [99.189285] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:35:plane 1A]
<7> [99.205940] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [99.207472] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [99.208111] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<6> [99.223309] Console: switching to colour frame buffer device 180x56
|