Results for igt@kms_chamelium_audio@dp-audio-edid

Result: Skip

i915_display_info22 igt_runner22 results22.json results22-xe-load.json guc_logs22.tar i915_display_info_post_exec22 boot22 dmesg22

DetailValue
Duration 0.00 seconds
Hostname
shard-lnl-1
Igt-Version
IGT-Version: 2.4-ga5c5d6558 (x86_64) (Linux: 7.0.0-lgci-xe-xe-4934-fadd084d6cb1ca9d7-debug+ x86_64)
Out
Using IGT_SRANDOM=1777055910 for randomisation
Opened device: /dev/dri/card0
Test requirement not met in function chamelium_init_test, file ../tests/chamelium/kms_chamelium_helper.c:49:
Test requirement: data->chamelium
Subtest dp-audio-edid: SKIP (0.000s)
Err
Subtest dp-audio-edid: SKIP (0.000s)
Dmesg
<6> [89.576748] Console: switching to colour dummy device 80x25
<6> [89.577056] [IGT] kms_chamelium_audio: executing
<7> [89.583113] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [89.583133] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [89.583317] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [89.583579] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [89.583583] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [89.583709] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [89.583933] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [89.583936] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [89.584063] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<7> [89.584376] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1]
<7> [89.584381] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:393:eDP-1]
<7> [89.584838] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [89.585159] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [89.585271] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [89.585381] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [89.585500] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [89.585505] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [89.585506] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [89.585507] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [89.585509] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [89.585511] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [89.585512] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD monitor
<5> [89.585514] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [89.585515] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD size 20, SAD count 0
<5> [89.585517] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [89.585527] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] VRR capable: yes
<7> [89.585619] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [89.585705] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [89.586010] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [89.586013] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [89.586014] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [89.586057] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1] probed modes:
<7> [89.586061] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [89.586064] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [89.586075] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [89.586079] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [89.586222] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [89.586233] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [89.586236] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [89.586366] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [89.586375] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [89.586378] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [89.586498] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<7> [89.587352] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [89.587466] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [89.587553] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [89.587639] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [89.587724] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [89.587809] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [89.587892] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [89.587974] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [89.588054] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [89.588366] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [89.588464] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [89.588550] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [89.588629] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [89.588707] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [89.588785] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [89.588868] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [89.588951] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [89.589033] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [89.589108] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [89.589419] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [89.589522] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [89.589602] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [89.589680] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [89.589758] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [89.589834] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [89.589917] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [89.590000] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [89.590082] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [89.590177] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [89.590275] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [89.590382] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [89.590481] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [89.590556] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [89.590629] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [89.590706] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [89.590785] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [89.590865] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [89.590944] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [89.591017] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [89.591104] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:151:pipe A] releasing DPLL 0
<7> [89.591257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [89.591346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [89.591436] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [89.591522] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [89.591597] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [89.591670] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [89.591741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [89.591800] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [89.591870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [89.591970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [89.592074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [89.592265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [89.592378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [89.592479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [89.592571] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [89.592674] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [89.592762] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [89.592862] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [89.592966] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [89.593086] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: no [modeset]
<7> [89.593205] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [NOFB], visible: no
<7> [89.593312] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [89.593418] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [89.593518] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [89.593601] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [89.593686] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [89.593773] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:389:pipe C] enable: no [fastset]
<7> [89.593860] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:273:plane 1C] fb: [NOFB], visible: no
<7> [89.593943] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:303:plane 2C] fb: [NOFB], visible: no
<7> [89.594021] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:333:plane 3C] fb: [NOFB], visible: no
<7> [89.594098] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:363:plane 4C] fb: [NOFB], visible: no
<7> [89.594206] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:373:plane 5C] fb: [NOFB], visible: no
<7> [89.594308] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:383:cursor C] fb: [NOFB], visible: no
<7> [89.594457] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [89.594549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [89.594695] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [89.597756] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [89.597899] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [89.799321] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 0
<7> [89.799914] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [89.815557] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power off
<7> [89.815831] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [89.816022] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [89.816103] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [89.816365] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [89.868647] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [89.868979] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - short
<7> [89.875662] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [89.877003] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [89.877024] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:151:pipe A]
<7> [89.877504] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [89.878548] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [89.879039] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [89.879737] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [89.880248] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [89.880598] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [89.880915] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [89.881248] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [89.881551] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [89.881841] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [89.882125] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [89.882439] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [89.882719] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [89.883000] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [89.883294] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [89.883576] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [89.883856] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [89.884167] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:402:DP-1]
<7> [89.884453] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:414:DP-2]
<7> [89.884707] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:422:DP-3]
<7> [89.885039] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [89.885310] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [89.885554] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [89.886013] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [89.886414] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xaa000000)
<7> [89.886847] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [89.887196] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:389:pipe C]
<7> [89.887513] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [89.887976] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [89.888307] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [89.888711] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800010 0x9a00071)
<6> [89.891599] [IGT] kms_chamelium_audio: exiting, ret=77
<6> [89.893784] Console: switching to colour frame buffer device 180x56
<7> [89.900575] xe 0000:00:02.0: [drm:compute_baseline_pipe_bpp [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [89.900767] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [89.900891] xe 0000:00:02.0: [drm:intel_dp_compute_output_format [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [89.901021] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [89.901164] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A]
<7> [89.901283] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [89.901393] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [89.901501] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [89.901607] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [89.901712] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [89.901817] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [89.901923] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [89.902028] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [89.902141] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [89.902247] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [89.902351] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [89.902454] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [89.902557] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [89.902662] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [89.902767] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [89.902872] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [89.902976] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [89.903080] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [89.903290] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [89.903402] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [89.903508] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [89.903612] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [89.903715] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [89.903817] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [89.903919] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [89.904021] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [89.904124] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [89.904247] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [89.904350] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [89.904454] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [89.904556] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [89.904657] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [89.904759] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [89.904860] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [89.904965] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [89.905069] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [89.905176] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [89.905177] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [89.905279] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [89.905297] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [89.905383] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [89.905399] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [89.905521] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [89.905548] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [89.905636] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:151:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [89.905718] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [89.905793] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:145:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [89.905866] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [89.905938] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [89.906011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [89.906083] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [89.906191] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [89.906203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 1
<7> [89.906327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [89.906348] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [89.906445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [89.906474] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [89.906563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [89.906678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [89.906790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [89.906904] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [89.907049] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [89.907364] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [89.907484] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [89.907594] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [89.907746] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:151:pipe A] allocated DPLL 0
<7> [89.907852] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:151:pipe A] reserving DPLL 0
<7> [89.907970] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [modeset]
<7> [89.908093] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [89.909377] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [89.909526] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [89.909639] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [89.909750] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [89.909860] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [89.909970] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [89.910080] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [89.910206] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [89.910320] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [89.910430] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [89.910540] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum hblank: 0
<7> [89.910652] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [89.910760] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [89.910869] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [89.910979] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [89.911089] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [89.911206] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [89.911317] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [89.911426] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [89.911536] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [89.911645] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [89.911756] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [89.911865] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [89.911974] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [89.912087] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [89.912205] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [89.912317] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [89.912427] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [89.912537] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pixel rate 347710, min cdclk 173855, min voltage level 0
<7> [89.912646] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [89.912755] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0, sharpness_strength: 0
<7> [89.912866] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe src: 2880x1800+0+0
<7> [89.912975] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [89.913085] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [89.913201] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [89.913313] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [89.913423] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [89.913531] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [89.913641] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [89.913750] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [89.913859] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [89.913968] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [89.914078] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [89.914199] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [89.914310] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [89.914420] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [89.914528] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [89.914636] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [89.914745] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [89.914853] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [89.914960] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [89.915068] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [89.915184] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [89.915294] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [89.915403] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [89.915512] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [89.915621] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [89.915729] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:35:plane 1A] fb: [FB:394] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [89.915839] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [89.915947] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [89.916058] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [89.916175] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [89.916289] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [89.916400] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [89.916508] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [89.916743] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [89.917026] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [89.917209] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [89.917395] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [89.917612] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1800071 0xc01b072)
<7> [89.917760] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [89.917930] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [89.918054] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [89.918188] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:392:DDI A/PHY A]
<7> [89.918286] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DDI TC1/PHY TC1]
<7> [89.918372] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST A]
<7> [89.918456] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST B]
<7> [89.918540] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:405:DP-MST C]
<7> [89.918623] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DDI TC2/PHY TC2]
<7> [89.918707] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST A]
<7> [89.918789] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST B]
<7> [89.918875] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:417:DP-MST C]
<7> [89.918956] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DDI TC3/PHY TC3]
<7> [89.919036] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST A]
<7> [89.919117] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST B]
<7> [89.919277] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:425:DP-MST C]
<7> [89.919395] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [89.919587] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [89.919672] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [89.919805] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [89.920946] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:151:pipe A]
<7> [89.921094] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [89.923159] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turn panel power on
<7> [89.923257] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power cycle (453 ms remaining)
<7> [90.383265] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [90.393812] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [90.394262] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 wait for panel power on
<7> [90.394680] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [90.430889] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [90.431275] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:392:DDI A/PHY A] - long
<7> [90.431620] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [90.432016] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:392:DDI A/PHY A]
<7> [90.609538] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [90.610082] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7> [90.610570] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [90.612926] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [90.614632] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [90.615585] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [90.616807] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [90.618292] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [90.619492] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Clock recovery OK
<7> [90.619873] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [90.621549] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [90.622072] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:393:eDP-1][ENCODER:392:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [90.623003] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [90.623624] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [90.624026] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [90.624539] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:393:eDP-1] set backlight PWM = 4518
<7> [90.640453] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [90.642445] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]
<7> [90.642919] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]
<7> [90.646347] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [90.648286] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [90.648818] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [90.649249] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [90.649697] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [90.649697] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [90.649698] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
Created at 2026-04-24 18:59:09