Results for igt@kms_plane_scaling@plane-downscale-factor-0-75-with-modifiers@pipe-a

Result: Pass

i915_display_info22 igt_runner22 results22.json results22-xe-load.json guc_logs22.tar i915_display_info_post_exec22 boot22 dmesg22

DetailValue
Duration 0.51 seconds
Hostname 
shard-lnl-3
Igt-Version 
IGT-Version: 2.4-g574c502c4 (x86_64) (Linux: 7.0.0-rc6-lgci-xe-xe-4847-76473eaa4f4d39153-debug+ x86_64)
Out 
Using IGT_SRANDOM=1775228375 for randomisation
Opened device: /dev/dri/card0
Starting subtest: plane-downscale-factor-0-75-with-modifiers
Starting dynamic subtest: pipe-A
Trying on eDP-1
Dynamic subtest pipe-A: SUCCESS (0.510s)
Err 
Starting subtest: plane-downscale-factor-0-75-with-modifiers
Starting dynamic subtest: pipe-A
Dynamic subtest pipe-A: SUCCESS (0.510s)
Dmesg
<6> [129.894370] Console: switching to colour dummy device 80x25
<6> [129.894689] [IGT] kms_plane_scaling: executing
<7> [129.900342] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [129.900351] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [129.900500] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [129.900592] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [129.900975] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [129.900980] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [129.901118] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [129.901211] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [129.901418] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [129.901421] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [129.901529] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [129.901610] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<7> [129.901878] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1]
<7> [129.901882] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:393:eDP-1]
<7> [129.901996] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD on
<7> [129.902120] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f
<7> [129.902547] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [129.902861] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [129.902969] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [129.903077] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [129.903194] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [129.903199] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [129.903201] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [129.903203] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [129.903206] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [129.903209] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [129.903211] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD monitor
<5> [129.903214] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [129.903216] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD size 20, SAD count 0
<5> [129.903219] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [129.903230] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] VRR capable: yes
<7> [129.903309] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [129.903388] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [129.903694] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [129.903696] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [129.903697] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [129.903755] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1] probed modes:
<7> [129.903758] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [129.903762] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [129.903916] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]
<7> [129.903921] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]
<7> [129.904063] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected
<7> [129.904073] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]
<7> [129.904076] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]
<7> [129.904211] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected
<7> [129.904221] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]
<7> [129.904223] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]
<7> [129.904337] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected
<6> [129.904698] [IGT] kms_plane_scaling: starting subtest plane-downscale-factor-0-75-with-modifiers
<6> [129.905098] [IGT] kms_plane_scaling: starting dynamic subtest pipe-A
<7> [129.906575] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [129.907267] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.0: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x1
<7> [129.907368] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [129.907439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [129.907507] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [129.907574] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [129.907650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [129.907759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [129.907988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [129.908095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [129.908183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [129.908269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [129.908371] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:151:pipe A] min cdclk: 173855 kHz -> 309076 kHz
<7> [129.908473] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 38635 kHz
<7> [129.908563] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via crawling and squashing
<7> [129.908655] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 330000 kHz, actual 330000 kHz
<7> [129.908745] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 1, actual 1
<7> [129.908889] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:35
<7> [129.911151] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [129.911248] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [129.911370] xe 0000:00:02.0: [drm:intel_pmdemand_program_params [xe]] initiate pmdemand request values: (0x1801071 0x14a1b072)
<7> [129.911822] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 330000 kHz, VCO 960000 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 1
<7> [129.916834] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 6 (mbus joined: yes)
<7> [129.916959] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=825
<7> [129.932344] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [129.932536] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [129.932578] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:35:plane 1A] because [FB:432] is removed
<7> [129.932614] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.0: Staged freeing scaler id 0 scaler_users = 0x0
<7> [129.932759] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [129.932912] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [129.933008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [129.933099] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [129.933186] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [129.933290] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [129.933416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [129.933540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [129.933658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [129.933788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [129.933901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [129.934259] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [129.949849] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [129.950020] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.0: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x1
<7> [129.950253] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [129.950421] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [129.950559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [129.950692] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [129.950858] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [129.951009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [129.951222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [129.951399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [129.951564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [129.951728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [129.951907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [129.952265] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:35
<7> [129.965041] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [129.966742] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:433] from all active usage due to RMFB ioctl
<7> [129.966852] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:35:plane 1A] because [FB:433] is removed
<7> [129.966910] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.0: Staged freeing scaler id 0 scaler_users = 0x0
<7> [129.967222] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [129.967476] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [129.967717] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [129.968067] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [129.968280] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [129.968575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [129.968922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [129.969224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [129.969540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [129.969846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [129.970136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [129.970993] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [129.987233] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [129.987452] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.0: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x1
<7> [129.987798] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [129.988096] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [129.988322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [129.988534] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 92, 502, 502, 502, 502, 502, 0, 0, 197, 92, 197
<7> [129.988742] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 183, 638, 638, 638, 638, 638, 0, 0, 198, 183, 198
<7> [129.989026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [129.989318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [129.989594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [129.989858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [129.990101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [129.990329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [129.990605] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:35
<7> [129.998396] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.000539] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [130.000628] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:35:plane 1A] because [FB:432] is removed
<7> [130.000677] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.0: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.001100] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.001412] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.001639] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.001902] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 92, 502, 502, 502, 502, 502, 0, 0, 197, 92, 197 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.002114] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 183, 638, 638, 638, 638, 638, 0, 0, 198, 183, 198 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.002354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.002642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.002951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.003213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.003468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.003751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.004358] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.016213] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [130.016469] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.1: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x2
<7> [130.017028] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.017294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.017522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.017741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [130.018073] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [130.018303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.018627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.018917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.019177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.019431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.019706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.020015] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:65
<7> [130.031720] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.033448] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [130.033543] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:65:plane 2A] because [FB:432] is removed
<7> [130.033604] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.1: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.033997] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.034281] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.034486] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.034695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.034944] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.035157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.035429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.035679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.035947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.036186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.036410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.036972] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.050024] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [130.050253] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.1: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x2
<7> [130.050607] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.050957] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.051224] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.051487] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [130.051804] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [130.052087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.052567] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.1: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x2
<7> [130.052894] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.053132] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.053360] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.053577] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [130.053844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [130.054064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.054372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.054659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.054995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.055275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.055567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.055883] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:65
<7> [130.064998] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.066541] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:433] from all active usage due to RMFB ioctl
<7> [130.066620] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:65:plane 2A] because [FB:433] is removed
<7> [130.066671] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.1: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.067022] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.067193] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.067337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.067471] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.067600] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.067744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.067966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.068148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.068319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.068484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.068643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.069079] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.083142] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [130.083356] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.1: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x2
<7> [130.083694] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.084029] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.084280] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.084521] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 92, 502, 502, 502, 502, 502, 0, 0, 197, 92, 197
<7> [130.084829] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 183, 638, 638, 638, 638, 638, 0, 0, 198, 183, 198
<7> [130.085092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.085408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.085729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.086121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.086396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.086707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.087049] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:65
<7> [130.098359] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.100200] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [130.100278] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:65:plane 2A] because [FB:432] is removed
<7> [130.100328] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.1: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.100642] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.101016] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.101243] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.101512] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 92, 502, 502, 502, 502, 502, 0, 0, 197, 92, 197 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.101715] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 183, 638, 638, 638, 638, 638, 0, 0, 198, 183, 198 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.101989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.102278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.102545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.102810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.103071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.103316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.103947] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.116305] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [130.116566] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.2: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x4
<7> [130.116950] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:95:plane 3A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.117227] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.117455] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.117675] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [130.117999] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [130.118241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.118553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.118849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.119125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.119395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.119700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.120033] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:95
<7> [130.131702] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.133412] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [130.133487] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:95:plane 3A] because [FB:432] is removed
<7> [130.133534] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.2: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.133858] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:95:plane 3A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.134138] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.134361] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] lines 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.134575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] blocks 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.134876] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] min_ddb 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.135100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.135399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.135681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.135981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.136236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.136484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.137092] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.150099] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [130.150322] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.2: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x4
<7> [130.150671] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:95:plane 3A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.151016] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.151283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.151542] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [130.151826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [130.152090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.152448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.152760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.153149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.153473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.153785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.154161] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:95
<7> [130.164996] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.166701] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:433] from all active usage due to RMFB ioctl
<7> [130.166799] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:95:plane 3A] because [FB:433] is removed
<7> [130.166848] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.2: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.167139] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:95:plane 3A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.167374] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.167596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] lines 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.167875] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] blocks 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.168096] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] min_ddb 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.168385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.168698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.169008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.169299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.169575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.169862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.170485] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.183124] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [130.183338] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.2: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x4
<7> [130.183685] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:95:plane 3A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.184051] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.184306] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.184589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 92, 502, 502, 502, 502, 502, 0, 0, 197, 92, 197
<7> [130.184863] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 183, 638, 638, 638, 638, 638, 0, 0, 198, 183, 198
<7> [130.185133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.185478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.185821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.186126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.186422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.186786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.187139] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:95
<7> [130.198369] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.200060] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [130.200144] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:95:plane 3A] because [FB:432] is removed
<7> [130.200193] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.2: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.200508] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:95:plane 3A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.200788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.201016] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] lines 4, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.201255] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] blocks 92, 502, 502, 502, 502, 502, 0, 0, 197, 92, 197 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.201504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:95:plane 3A] min_ddb 183, 638, 638, 638, 638, 638, 0, 0, 198, 183, 198 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.201748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.202152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.202458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.202809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.203080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.203389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.203994] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.216203] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [130.216440] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.3: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x8
<7> [130.216754] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.217067] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.217295] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.217515] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [130.217811] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [130.218052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.218380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.218698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.219036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.219387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.219687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.220058] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:125
<7> [130.231688] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.233434] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [130.233516] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:125:plane 4A] because [FB:432] is removed
<7> [130.233565] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.3: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.233935] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.234233] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.234458] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.234694] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.234975] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.235218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.235552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.235844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.236124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.236412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.236691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.237337] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.250029] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [130.250247] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.3: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x8
<7> [130.250560] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.250888] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.251131] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.251394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [130.251654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [130.251990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.252340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.252680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.253053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.253438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.253751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.254164] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:125
<7> [130.264987] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.266684] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:433] from all active usage due to RMFB ioctl
<7> [130.266778] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:125:plane 4A] because [FB:433] is removed
<7> [130.266827] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.3: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.267133] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.267386] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.267619] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.267915] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.268157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.268430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.268755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.269080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.269340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.269593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.269906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.270508] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.283129] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [130.283346] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.3: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x8
<7> [130.283689] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.284026] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.284268] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.284501] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 92, 502, 502, 502, 502, 502, 0, 0, 197, 92, 197
<7> [130.284790] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 183, 638, 638, 638, 638, 638, 0, 0, 198, 183, 198
<7> [130.285076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.285414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.285723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.286083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.286381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.286673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.287066] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:125
<7> [130.298337] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.299958] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [130.300029] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:125:plane 4A] because [FB:432] is removed
<7> [130.300076] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.3: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.300363] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.300638] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.300936] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.301193] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 92, 502, 502, 502, 502, 502, 0, 0, 197, 92, 197 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.301450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 183, 638, 638, 638, 638, 638, 0, 0, 198, 183, 198 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.301753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.302138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.302442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.302719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.303085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.303338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.304015] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.316022] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [130.316300] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.4: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x10
<7> [130.316583] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.316909] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.317116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.317319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [130.317557] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [130.317802] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.318226] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.4: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x10
<7> [130.318455] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.318658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.318890] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.319095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [130.319286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [130.319475] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.319741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.320042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.320343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.320580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.320826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.321151] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:135
<7> [130.331624] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.333060] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [130.333135] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:135:plane 5A] because [FB:432] is removed
<7> [130.333181] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.4: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.333470] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.333706] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.333990] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.334209] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.334450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.334682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.335030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.335336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.335635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.336010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.336257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.336886] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.349900] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [130.350036] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.4: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x10
<7> [130.350200] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.350297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.350386] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.350472] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111
<7> [130.350553] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112
<7> [130.350648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.350799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.350917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.351034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.351149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.351261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.351405] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:135
<7> [130.364940] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.366256] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:433] from all active usage due to RMFB ioctl
<7> [130.366331] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:135:plane 5A] because [FB:433] is removed
<7> [130.366380] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.4: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.366674] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.367001] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.367229] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 2, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.367451] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 49, 529, 529, 529, 529, 529, 0, 0, 63, 97, 111 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.367670] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 55, 583, 583, 583, 583, 583, 0, 0, 64, 108, 112 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.367972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.368221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.368458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.368689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.368939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.369151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.369698] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [130.382239] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [130.382322] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.4: staged scaling request for 2880x1800->2160x1350 scaler_users = 0x10
<7> [130.382431] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [130.382508] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [130.382580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0
<7> [130.382650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 92, 502, 502, 502, 502, 502, 0, 0, 197, 92, 197
<7> [130.382720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 183, 638, 638, 638, 638, 638, 0, 0, 198, 183, 198
<7> [130.382824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2472608 num active planes 1
<7> [130.382942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2597 qgv_peak_bw: 38400
<7> [130.383058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2597 qgv_peak_bw: 38400
<7> [130.383164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.383259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2597 qgv_peak_bw: 38400
<7> [130.383358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2597
<7> [130.383497] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:151:pipe A] attached scaler id 0.0 to PLANE:135
<7> [130.398311] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [130.399386] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:432] from all active usage due to RMFB ioctl
<7> [130.399416] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:135:plane 5A] because [FB:432] is removed
<7> [130.399435] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:151:pipe A] scaler_user index 0.4: Staged freeing scaler id 0 scaler_users = 0x0
<7> [130.399534] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [130.399604] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [130.399672] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 22, 22, 22, 22, 22, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.399741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 92, 502, 502, 502, 502, 502, 0, 0, 197, 92, 197 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.399841] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 183, 638, 638, 638, 638, 638, 0, 0, 198, 183, 198 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [130.400081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [130.400191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [130.400280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [130.400360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.400439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [130.400517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [130.400713] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<6> [130.415410] [IGT] kms_plane_scaling: finished subtest pipe-A, SUCCESS
Created at 2026-04-03 15:24:53