igt@kms_rotation_crc@multiplane-rotation-cropping-bottom on shard-lnl@xe-4772-84e58d2aeaa1e5871d5f58a75283589b05415f7e Test details

Detail	Value
Duration	28.81 seconds
Hostname	shard-lnl-8
Igt-Version	IGT-Version: 2.3-g31b303e63 (x86_64) (Linux: 7.0.0-rc5-lgci-xe-xe-4772-84e58d2aeaa1e5871-debug+ x86_64)
Out	Using IGT_SRANDOM=1774405521 for randomisation Opened device: /dev/dri/card0 Starting subtest: multiplane-rotation-cropping-bottom Subtest multiplane-rotation-cropping-bottom: SUCCESS (28.811s)
Err	Starting subtest: multiplane-rotation-cropping-bottom Subtest multiplane-rotation-cropping-bottom: SUCCESS (28.811s)
Dmesg	<6> [268.344599] Console: switching to colour dummy device 80x25 <6> [268.344905] [IGT] kms_rotation_crc: executing <7> [268.350320] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] <7> [268.350329] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1] <7> [268.350479] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7> [268.350571] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected <7> [268.350818] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] <7> [268.350821] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2] <7> [268.350939] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7> [268.351024] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected <7> [268.351230] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] <7> [268.351233] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3] <7> [268.351345] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4 <7> [268.351426] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected <7> [268.351690] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1] <7> [268.351693] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:393:eDP-1] <7> [268.352157] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7> [268.352472] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7> [268.352681] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [268.352774] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [268.352878] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5> [268.352883] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [268.352885] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [268.352885] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7> [268.352888] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5> [268.352890] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [268.352891] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD monitor <5> [268.352894] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [268.352895] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD size 20, SAD count 0 <5> [268.352897] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [268.352909] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] VRR capable: yes <7> [268.352992] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [268.353075] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5> [268.353385] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [268.353387] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [268.353389] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [268.353444] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1] probed modes: <7> [268.353447] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [268.353451] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [268.353464] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] <7> [268.353467] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1] <7> [268.353626] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected <7> [268.353638] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] <7> [268.353641] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2] <7> [268.353766] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected <7> [268.353776] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] <7> [268.353779] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3] <7> [268.353902] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected <6> [268.354154] [IGT] kms_rotation_crc: starting subtest multiplane-rotation-cropping-bottom <7> [268.355436] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0 <7> [268.355512] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [268.355572] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.355652] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.355715] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.355792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0 <7> [268.355881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400 <7> [268.355967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400 <7> [268.356053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [268.356139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [268.356225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0 <7> [268.356536] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.356720] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [268.356851] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2 <7> [268.382758] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A <7> [268.383223] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A <7> [268.383671] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [268.383925] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000 <7> [268.384156] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000 <7> [268.384383] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation <7> [268.384571] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [268.384836] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A] <7> [268.385134] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [fastset] <7> [268.385418] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [268.385673] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [268.385917] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid> <7> [268.386156] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [268.386393] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7> [268.387207] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7> [268.387461] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7> [268.387754] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [268.388006] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7> [268.388314] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7> [268.388563] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled <7> [268.388871] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7> [268.389172] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [268.389407] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8 <7> [268.389650] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7> [268.389887] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7> [268.390107] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7> [268.390328] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7> [268.390538] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7> [268.390836] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7> [268.391065] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7> [268.391258] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97 <7> [268.391450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906 <7> [268.391643] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0 <7> [268.391856] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [268.392045] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [268.392221] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [268.392389] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [268.392551] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [268.393156] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7> [268.393307] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7> [268.393453] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [268.393623] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [268.393783] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7> [268.393921] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no <7> [268.394057] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no, <7> [268.394191] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1. <7> [268.394320] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state: <7> [268.394447] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21 <7> [268.394574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <7> [268.394723] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7> [268.394862] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7> [268.395004] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7> [268.395120] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7> [268.395241] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [268.395353] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [268.395464] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [268.395572] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [268.396023] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [268.396134] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [268.396240] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [268.396343] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [268.396444] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [268.396542] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [268.396653] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [268.396749] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [268.396845] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7> [268.399930] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1] <7> [268.400089] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A] <7> [268.419749] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [268.420117] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [268.420404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [268.449877] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:429] <7> [268.472308] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026 <7> [268.472610] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025 <7> [268.472824] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.473021] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [268.473211] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [268.473434] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [268.473670] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.473847] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [268.474021] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [268.474188] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [268.474413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [268.474720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [268.474991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [268.475256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [268.475517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [268.475836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [268.476650] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.476922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [268.477682] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [268.477927] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:35:plane 1A] <7> [268.482185] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1 <7> [268.484259] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:450] <7> [268.532728] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:451] <7> [268.533837] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [268.534285] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [268.534684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [268.549919] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [268.550257] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [268.550474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.550721] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [268.550921] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [268.551101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [268.551339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [268.551604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [268.551843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [268.552069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [268.552282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [268.552480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [268.552904] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 43464 kHz <7> [268.553446] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.553736] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [268.583250] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:452] <7> [268.583646] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [268.584079] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [268.584443] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [268.602113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [268.602363] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [268.602531] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [268.602840] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [268.603003] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.603149] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [268.603287] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [268.603417] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [268.603563] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.603920] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [268.604047] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [268.604154] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [268.604279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [268.604443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [268.604604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [268.604755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [268.604901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [268.605042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [268.605480] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.605623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [268.616771] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:453] <7> [268.631036] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [268.650059] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [268.650538] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [268.651066] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:454] <7> [268.650983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [268.667705] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [268.667914] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [268.668045] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [268.668162] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [268.668271] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.668375] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [268.668474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [268.668579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [268.668758] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.668861] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [268.668954] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [268.669048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [268.669150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [268.669281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [268.669406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [268.669530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [268.669667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [268.669784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [268.670252] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.670368] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [268.683497] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:455] <7> [268.697814] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [268.716131] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:456] <7> [268.717625] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [268.718075] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [268.718467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [268.731133] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [268.731352] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [268.731515] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [268.731699] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.731838] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [268.731974] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [268.732104] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [268.732245] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [268.732382] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.732499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.732650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.732790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [268.732960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [268.733118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [268.733274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [268.733418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [268.733562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [268.734069] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.734211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [268.766121] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:457] <7> [268.767631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [268.768147] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [268.768644] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [268.790448] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [268.790644] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [268.790762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.790873] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [268.790985] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [268.791089] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [268.791207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [268.791360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [268.791500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [268.791636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [268.791758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [268.791878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [268.792280] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.792400] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [268.816637] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [268.816978] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:458] <7> [268.817220] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [268.817728] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [268.837934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [268.838220] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [268.838394] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [268.838552] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [268.838748] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.838895] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [268.839031] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [268.839184] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [268.839331] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.839451] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [268.839571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [268.839744] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [268.839896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [268.840076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [268.840246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [268.840410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [268.840568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [268.840748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [268.841441] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.841605] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [268.850027] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:459] <7> [268.863166] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [268.883174] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [268.883553] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [268.884009] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:460] <7> [268.883946] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [268.899264] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [268.899506] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [268.899664] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [268.899782] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [268.899894] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.899999] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [268.900101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [268.900209] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [268.900319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.900426] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [268.900515] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [268.900616] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [268.900719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [268.900936] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [268.901059] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [268.901159] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [268.901254] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [268.901348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.901439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [268.901531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [268.901760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [268.901856] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.901950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [268.902023] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [268.902092] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [268.902166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [268.902282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [268.902393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [268.902500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [268.902630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [268.902739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [268.903140] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.903241] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [268.916906] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:461] <7> [268.932563] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [268.932707] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [268.932845] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [268.932956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [268.933050] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.933160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [268.966422] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:462] <7> [268.966763] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [268.967321] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [268.967820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [268.987278] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [268.987396] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [268.987490] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [268.987595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.987686] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [268.987776] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [268.987864] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [268.987942] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [268.988013] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.988082] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.988154] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.988239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [268.988390] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [268.988454] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [268.988513] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [268.988572] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [268.988668] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [268.988739] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [268.988808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [268.988876] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [268.988932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.988983] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.989035] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [268.989096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [268.989191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [268.989277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [268.989362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [268.989444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [268.989526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [268.989880] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [268.989994] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.016171] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:463] <7> [269.016655] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.017210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.017690] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.037761] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [269.037875] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [269.037969] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.038056] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.038124] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [269.038190] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [269.038268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [269.038415] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [269.038486] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [269.038554] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.039313] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.039376] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [269.039433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [269.039494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [269.039639] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [269.039722] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [269.039802] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.039881] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.039946] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [269.040000] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [269.040058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [269.040153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [269.040249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [269.040333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [269.040416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [269.040499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [269.040821] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.040932] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.066559] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:464] <7> [269.066662] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.067045] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.067364] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.085615] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.085806] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [269.085943] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [269.086054] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [269.086152] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.086249] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.086341] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [269.086430] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [269.086517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.086627] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.086711] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [269.086794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [269.086891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [269.087117] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.087225] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [269.087310] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [269.087387] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [269.087458] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.087527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.087609] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [269.087679] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [269.087746] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.087817] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.087895] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [269.087962] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [269.088031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [269.088139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [269.088241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [269.088340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [269.088438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [269.088535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [269.088995] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.089089] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.099642] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:465] <7> [269.113206] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.132612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.133077] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:466] <7> [269.132973] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.133267] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.147969] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.148173] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [269.148280] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [269.148380] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [269.148475] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.148568] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.148961] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [269.149056] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [269.149141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.149225] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.149308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [269.149390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [269.149494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [269.149693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [269.149814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [269.149928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [269.150029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [269.150127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [269.150602] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.150717] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.166881] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:467] <7> [269.182162] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.215957] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:468] <7> [269.216774] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.217226] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.217619] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.234242] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026 <7> [269.234438] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025 <7> [269.234627] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [269.234783] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.234933] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [269.235075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [269.235232] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [269.235385] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [269.235511] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [269.235745] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [269.235866] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [269.236008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [269.236211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [269.236384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [269.236539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [269.236715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [269.236863] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [269.237261] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.237415] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.249531] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:469] <7> [269.299126] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:470] <7> [269.299649] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.300114] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.300457] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.317740] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [269.318014] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [269.318175] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.318326] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [269.318475] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [269.318759] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [269.318921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [269.319130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [269.319306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [269.319475] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [269.319669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [269.319823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [269.320298] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.320450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.349632] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:471] <7> [269.349638] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.350046] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.350359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.369846] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.370189] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [269.370428] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [269.370702] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [269.370912] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.371116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [269.371319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [269.371517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [269.371801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.371997] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [269.372192] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [269.372424] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [269.372698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [269.373008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [269.373281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [269.373557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [269.373869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [269.374188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [269.375013] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.375287] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.382965] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:472] <7> [269.389648] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.389849] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.390009] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.390238] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [269.390239] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [269.390239] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [269.398595] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.399421] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.399931] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.433357] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:473] <7> [269.433627] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.434094] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.434506] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.456526] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.456835] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [269.456991] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [269.457131] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [269.457261] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.457384] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [269.457502] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [269.457658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [269.457791] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.457900] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [269.458008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [269.458122] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [269.458237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [269.458391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [269.458538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [269.458695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [269.458854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [269.459008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [269.459486] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.459618] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.467508] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:474] <7> [269.482210] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.517482] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.517750] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:475] <7> [269.517974] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.518397] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.533547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [269.533747] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [269.533880] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [269.534003] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.534118] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [269.534231] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [269.534353] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [269.534475] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [269.534602] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [269.534704] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [269.534803] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [269.534934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [269.535105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [269.535257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [269.535391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [269.535518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [269.535695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [269.536097] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.536222] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.580016] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.580209] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:476] <7> [269.580228] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.580366] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.588823] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [269.588981] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [269.589079] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.589167] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [269.589252] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [269.589337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [269.589445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [269.589712] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [269.589815] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [269.589911] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.590006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [269.590102] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [269.590195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [269.590298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [269.590462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [269.590639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [269.590801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [269.590958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [269.591124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [269.591822] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.592002] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.617626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.618142] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:477] <7> [269.618222] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.618701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.645229] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.645628] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [269.645787] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [269.645922] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [269.646054] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.646185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [269.646312] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [269.646431] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [269.646557] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.646712] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [269.646840] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [269.646939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [269.647097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [269.647460] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.647624] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [269.647722] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [269.647824] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [269.647908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.647996] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [269.648081] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [269.648164] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [269.648247] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.648330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [269.648411] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [269.648520] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [269.648619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [269.648753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [269.648880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [269.649002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [269.649117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [269.649230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [269.649850] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.649974] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.691034] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.691188] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.691297] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.691645] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:478] <7> [269.704748] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.705388] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.705522] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.733633] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.733964] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.734226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.737469] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:479] <7> [269.763163] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.763511] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [269.763771] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [269.763961] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [269.764132] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.764298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [269.764451] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [269.764646] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [269.764792] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.764935] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [269.765068] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [269.765192] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [269.765338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [269.765718] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.765867] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [269.765984] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [269.766094] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [269.766196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.766297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [269.766398] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [269.766494] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [269.767011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.767110] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [269.767202] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [269.767291] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [269.767385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [269.767527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [269.767722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [269.767855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [269.767980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [269.768102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [269.768683] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.768808] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.801286] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.801442] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.801545] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.801589] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:480] <7> [269.809643] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.810003] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.810114] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.832610] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.832952] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.833120] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:481] <7> [269.833187] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.845828] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [269.846013] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [269.846147] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [269.846277] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.846402] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.846522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [269.846794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [269.846936] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [269.847053] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [269.847159] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [269.847258] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [269.847378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [269.847532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [269.847756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [269.847911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [269.848045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [269.848172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [269.848646] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.848786] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.882525] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:482] <7> [269.882639] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.883111] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.883531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.902415] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [269.902753] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [269.903009] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.903252] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.903488] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [269.903960] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [269.904223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [269.904552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [269.904919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [269.905246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [269.905568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [269.906099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [269.907036] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.907323] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.933152] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:483] <7> [269.933636] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.934112] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.934495] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.956070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.956494] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [269.956848] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [269.957099] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [269.957336] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.957558] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.957829] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [269.958039] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [269.958269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [269.958457] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [269.958674] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [269.958861] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [269.959107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [269.959380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [269.959633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [269.959898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [269.960124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [269.960333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [269.961164] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.961358] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [269.966516] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:484] <7> [269.982635] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [269.983006] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [269.983298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [269.983806] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [269.984845] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [269.985164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.016538] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:485] <7> [270.016647] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.016998] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.017338] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.040095] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.040444] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [270.040805] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [270.041043] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [270.041271] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.041493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [270.041756] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [270.041976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [270.042251] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.042464] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [270.042710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [270.042899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [270.043111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [270.043376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [270.043638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [270.043877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.044111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.044333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [270.045214] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.045420] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.050081] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:486] <7> [270.067467] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.067694] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.067942] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.068138] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.068319] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.068488] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.098778] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691 <7> [270.099008] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360 <7> [270.099213] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [270.099409] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.099667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.099650] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.099925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.099972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.100130] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.100250] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.100328] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.100521] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.100773] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.101004] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.101201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [270.101388] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.101596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.101784] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.102051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [270.102351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [270.102659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [270.102960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.103266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.103568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [270.104457] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.104799] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.148824] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [270.149090] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [270.149296] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.149485] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.149718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.149889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.149839] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.150101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [270.150171] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.150368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [270.150441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.150638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [270.150892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.151144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.151389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [270.152065] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.152323] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.182378] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:487] <7> [270.182727] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.183103] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.183407] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.200519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.201050] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [270.201277] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [270.201487] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [270.201900] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.202097] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.202275] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.202448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.202641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.202808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [270.202982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [270.203156] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [270.203346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [270.203612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [270.203866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [270.204101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [270.204324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [270.204539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [270.205265] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.205475] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.215767] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.248747] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.249015] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [270.249249] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [270.249436] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [270.249664] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.249676] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.249856] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.250042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.250027] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.250264] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.250325] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.250453] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.250665] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.250833] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.250997] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.251214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [270.251597] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.251810] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [270.252027] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [270.252203] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [270.252372] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.252537] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.252814] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.253012] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.253209] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.253376] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.253545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.253786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.253981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [270.254292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [270.254615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [270.254952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [270.255277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [270.255620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [270.256105] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 43464 kHz -> 65196 kHz <7> [270.257111] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.257447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.265597] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.298803] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [270.299043] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [270.299252] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [270.299451] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.299698] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.299891] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.299831] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.300107] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.300207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.300290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [270.300470] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.300499] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.300711] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.300890] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.301080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [270.301448] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [270.301652] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [270.301831] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [270.302006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.302216] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.302400] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.302565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.302797] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [270.302974] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.303148] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.303358] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.303592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [270.303879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [270.304168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [270.304450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.304800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.305117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [270.306014] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.306324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.332035] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [270.332282] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [270.332491] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.332746] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.332926] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.332892] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.333119] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.333220] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.333313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [270.333487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.333706] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [270.333881] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [270.334055] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.334226] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.334396] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.334562] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.334789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [270.335143] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [270.335299] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [270.335452] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.335628] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.335789] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.335947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.336118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [270.336441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [270.336736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [270.336996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.337256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.337568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [270.338400] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.338686] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.365395] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.365765] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [270.365843] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.365981] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [270.366177] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [270.366192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.366368] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.366485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.366553] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.366795] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.366993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.367203] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.367393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [270.367565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [270.367794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [270.367991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [270.368452] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.368693] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [270.368888] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [270.369053] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [270.369214] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.369372] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.369553] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.369816] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.369991] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.370153] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [270.370312] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [270.370471] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [270.370671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [270.370938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [270.371189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [270.371433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [270.371715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [270.372052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [270.373100] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.373347] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.382000] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.415343] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.415661] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [270.415687] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.415861] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [270.416045] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [270.416015] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.416226] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.416288] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.416404] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.416595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.416785] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.416982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.417160] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.417338] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.417513] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.417762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [270.418027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [270.418286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [270.418543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [270.418835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [270.419097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [270.420082] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.420356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.432385] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.465500] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [270.465772] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [270.465909] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.465984] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [270.466188] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.466260] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.466385] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [270.466543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.466598] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [270.466796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [270.466975] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [270.467147] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.467321] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.467505] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.467731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [270.467991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [270.468251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [270.468504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.468781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.469025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [270.469754] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.470018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.498714] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [270.498921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [270.499105] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.499286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [270.499485] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [270.499711] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [270.499833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.499919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [270.500185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [270.500185] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.500452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [270.500479] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.500744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.500989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.501228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [270.502015] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.502285] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.531978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.532227] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [270.532411] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [270.532624] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [270.532800] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.532774] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.532971] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [270.533102] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.533171] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [270.533351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [270.533376] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.533511] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.533698] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [270.533856] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [270.534010] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [270.534187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [270.534437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [270.534716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [270.534968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [270.535222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [270.535524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [270.536507] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.536801] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.548889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.581948] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.582192] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [270.582374] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [270.582549] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [270.582789] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.582956] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [270.582886] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.583116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [270.583274] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [270.583216] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.583428] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.583489] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.583596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [270.583757] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [270.583916] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [270.584130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [270.584398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [270.584664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [270.584909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [270.585196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [270.585435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [270.586368] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.586687] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.598901] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.631967] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691 <7> [270.632176] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360 <7> [270.632363] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0 <7> [270.632543] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.632789] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.632958] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.632938] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.633156] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.633270] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.633334] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [270.633490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.633545] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.633679] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.633836] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.634048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [270.634313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [270.634562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [270.634852] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.635101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.635349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [270.636048] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.636317] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.665312] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [270.665501] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [270.665730] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.665903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.665874] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.666086] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.666278] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.666255] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.666466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [270.666541] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.666749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [270.666993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [270.667243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.667482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.667754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [270.668387] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.668650] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.698642] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.698864] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [270.699062] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [270.699220] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [270.699376] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.699531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.699754] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.699940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.699881] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.700095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.700251] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [270.700207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.700407] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [270.700483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.700558] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [270.700791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [270.701198] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.701400] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [270.701559] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [270.701786] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [270.701941] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.702091] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.702270] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.702439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.703144] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.703288] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [270.703426] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [270.703565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [270.703777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [270.704028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [270.704274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [270.704518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [270.704793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [270.705069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [270.705792] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.706050] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.715453] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.748691] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.748971] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [270.749180] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [270.749376] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [270.749596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.749787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.749716] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.749976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.750071] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.750204] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.750364] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.750413] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.750661] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.750844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.751009] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.751195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [270.751547] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.751787] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [270.751983] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [270.752163] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [270.752323] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.752483] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.752679] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.752879] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.753042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.753200] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.753359] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.753516] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.753740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [270.754045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [270.754307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [270.754580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [270.754847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [270.755107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [270.755973] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.756236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.765358] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.798639] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [270.798860] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [270.799050] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [270.799230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.799405] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.799607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.799787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.799738] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.800005] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [270.800092] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.800194] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.800393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.800385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.800580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.800774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [270.801232] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [270.801412] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [270.801588] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [270.801755] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.801953] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.802141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.802350] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.802544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [270.802762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.802934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.803099] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.803273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [270.803542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [270.803846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [270.804161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.804423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.804717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [270.805516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.805829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.831952] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [270.832191] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [270.832390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.832609] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.832801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.832748] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.833028] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.833099] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.833251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [270.833392] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.833531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [270.833847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [270.834110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.834366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [270.834647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [270.835425] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.835735] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.865264] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.865518] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [270.865780] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [270.865816] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.865968] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [270.866150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.866164] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.866327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.866453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.866496] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.866756] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.866942] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.867163] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [270.867360] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [270.867533] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [270.867791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [270.868105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [270.868409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [270.868712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [270.869022] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [270.869305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [270.870409] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.870722] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.882284] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.915237] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.915506] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [270.915899] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [270.915898] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.916109] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [270.916249] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.916308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.916499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [270.916543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.916776] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [270.916959] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [270.917161] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.917326] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [270.917491] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [270.917690] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [270.917916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [270.918209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [270.918486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [270.918786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [270.919038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [270.919281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [270.920260] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.920529] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.932134] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [270.965434] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [270.965707] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [270.965828] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.965902] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [270.966085] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.966157] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [270.966262] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [270.966452] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [270.966431] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [270.966681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [270.966865] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [270.967043] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.967223] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.967424] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [270.967650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [270.967915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [270.968177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [270.968438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.968717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [270.969003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [270.969765] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [270.970023] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [270.989630] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD off <7> [270.989873] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 <7> [270.998658] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [270.998877] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [270.999066] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [270.999251] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [270.999439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [270.999681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [270.999713] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [270.999917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [271.000132] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.000227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [271.000471] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.000534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [271.000876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [271.001178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [271.001451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [271.002262] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.002548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.031893] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [271.032139] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [271.032322] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [271.032497] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [271.032727] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.032890] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.032849] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.033080] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [271.033179] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.033254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [271.033415] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.033452] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.033587] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.033745] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [271.033903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [271.034086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [271.034358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [271.034634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [271.034964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [271.035243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [271.035651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [271.036615] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.036909] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.048652] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [271.081864] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [271.082115] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [271.082331] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [271.082508] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [271.082742] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.082907] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.082878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.083070] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [271.083230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [271.083210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.083394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.083485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.083604] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.083775] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [271.083943] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [271.084135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [271.084408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [271.084699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [271.084994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [271.085235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [271.085473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [271.086422] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.086714] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.098709] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [271.131918] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.132195] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597 <7> [271.132425] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293 <7> [271.132664] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161 <7> [271.132841] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.132783] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.133011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.133119] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.133180] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.133358] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.133395] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.133515] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.133710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.133874] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.134037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.134202] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.134366] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.134526] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [271.134751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [271.134965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [271.135373] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.135617] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597 <7> [271.135807] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293 <7> [271.135994] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161 <7> [271.136171] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.136345] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.136519] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.136958] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.137200] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.137393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.137673] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.137882] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.138067] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.138243] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.138421] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [271.138631] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [271.138830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [271.139144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [271.139454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [271.139780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [271.140083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [271.140377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [271.141398] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.141742] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.148286] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:35:plane 1A] <7> [271.148725] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [271.148919] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [271.165640] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.198684] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.198983] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [271.199199] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [271.199406] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [271.199658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.199848] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [271.199784] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.200038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [271.200139] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.200261] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [271.200426] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.200510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [271.200970] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.201198] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [271.201373] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [271.201545] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [271.201762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.201940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [271.202122] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [271.202337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [271.202546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [271.202875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [271.203132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [271.203377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [271.203639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [271.203942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [271.204723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.204994] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.248728] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.249357] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.249752] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.249878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.250157] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [271.250354] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.250467] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [271.250780] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [271.250806] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.251013] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [271.251236] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.251456] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.251718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.251950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.252162] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.252372] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [271.252630] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [271.252846] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [271.253090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [271.253434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [271.253824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [271.254202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [271.254582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [271.254926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [271.256174] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.256527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.264936] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [271.282680] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.283039] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.315229] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.315466] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.315748] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [271.315841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.315999] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [271.316198] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [271.316196] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.316386] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [271.316481] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.316602] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.316789] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [271.316985] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [271.317208] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [271.317385] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.317559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.317792] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.317990] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.318216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [271.318716] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.318931] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.319155] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [271.319366] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [271.319535] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [271.319778] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [271.319989] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.320169] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [271.320332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [271.320524] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [271.320747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.320908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.321075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.321256] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.321420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [271.321722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [271.322011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [271.322272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [271.322577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [271.322826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [271.323711] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.323977] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.332138] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.332321] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.365637] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:488] <7> [271.365729] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.366183] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.366615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.385951] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.386325] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [271.386764] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [271.387022] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [271.387270] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [271.387517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.387819] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.388056] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.388320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.388537] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [271.388803] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.389006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.389210] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.389459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [271.389780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [271.390057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [271.390313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [271.390569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [271.390814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [271.391862] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.392091] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.392575] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [271.392757] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [271.398909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.431924] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.432278] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [271.432541] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [271.432905] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [271.433030] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.433173] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.433491] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [271.433508] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.433811] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [271.434000] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.434123] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [271.434451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [271.434894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [271.435289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [271.435668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [271.436084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [271.436458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [271.437615] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.438010] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.481999] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.482361] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.482764] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [271.482832] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.483018] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [271.483265] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [271.483268] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.483495] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [271.483664] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.483778] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.483999] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.484217] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.484459] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.484718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.484934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [271.485161] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [271.485394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [271.485705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [271.486057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [271.486427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [271.486812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [271.487163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [271.487462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [271.488791] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.489125] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.498257] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [271.515856] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.516144] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.548626] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.548968] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.549334] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [271.549707] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [271.549846] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.549970] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [271.550222] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [271.550365] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.550468] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.550778] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [271.550806] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.551056] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [271.551297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [271.551535] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.551902] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.552155] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.552396] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.552725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [271.553150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [271.553534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [271.553962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [271.554376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [271.554759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [271.556120] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.556462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.565485] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.565700] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.599093] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:489] <7> [271.599738] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.600182] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.600537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.619113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.619434] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [271.619706] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [271.619929] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [271.620148] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [271.620365] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.620740] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.620947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [271.621200] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [271.621424] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [271.621654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.621836] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.622011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.622212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [271.622474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [271.622746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [271.622985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [271.623217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [271.623465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [271.624423] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.624670] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.625139] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [271.625301] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [271.632210] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.665240] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.665698] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [271.665768] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.666071] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [271.666294] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.666372] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [271.666709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.666777] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.666997] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.667285] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [271.667559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [271.667951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [271.668548] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.668938] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [271.669210] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [271.669485] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [271.669824] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.670095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.670357] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [271.670751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [271.671009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [271.671389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [271.671801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [271.672230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [271.672601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [271.672990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [271.674013] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.674356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.715313] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.715838] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.715841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.716144] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.716271] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.716496] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [271.716680] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.716866] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [271.717112] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [271.717344] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [271.717603] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.717831] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.718054] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [271.718301] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [271.718520] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.718792] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.719005] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [271.719214] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [271.719457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [271.719832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [271.720185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [271.720533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [271.720952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [271.721253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [271.722501] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.722876] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.731539] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [271.749349] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.749739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.782033] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.782318] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.782639] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [271.782737] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.782899] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [271.783118] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [271.783144] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.783330] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [271.783476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.783541] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.783813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.784068] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [271.784281] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [271.784481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.784735] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [271.784976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [271.785188] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [271.785437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [271.785799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [271.786170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [271.786487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [271.786853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [271.787214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [271.788382] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.788727] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.798767] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.798954] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.831877] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.832222] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597 <7> [271.832474] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293 <7> [271.832795] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161 <7> [271.832945] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.833036] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [271.833322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.833384] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.833577] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.833838] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.833817] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.834047] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.834252] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [271.834460] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.834716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.834940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.835205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [271.835784] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.836056] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597 <7> [271.836304] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293 <7> [271.836516] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161 <7> [271.836773] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [271.836983] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.837183] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.837416] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.837664] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.837873] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [271.838069] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.838269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.838465] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [271.838718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [271.839019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [271.839350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [271.839698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [271.840009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [271.840315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [271.841225] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.841523] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.842260] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [271.842510] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [271.848775] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.881830] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.882180] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [271.882440] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [271.882753] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [271.882886] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.882981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.883201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [271.883292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.883448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [271.883702] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [271.883667] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.883948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [271.884255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [271.884573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [271.884888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [271.885197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [271.885513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [271.886400] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.886763] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.931881] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.932182] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.932461] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [271.932718] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [271.932901] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [271.932845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.933076] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [271.933180] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.933247] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.933413] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [271.933454] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.933598] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [271.933760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [271.933960] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [271.934146] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [271.934344] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [271.934506] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [271.934756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [271.935017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [271.935272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [271.935528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [271.935818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [271.936087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [271.937034] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [271.937338] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [271.948180] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [271.965891] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.966304] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.998489] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [271.998852] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [271.999005] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [271.999173] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [271.999460] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [271.999446] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [271.999760] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [271.999852] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [271.999993] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [272.000220] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.000484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [272.000764] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [272.000992] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [272.001232] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.001462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.001729] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.001973] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.002270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [272.002676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [272.003023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [272.003368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [272.003733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [272.004102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [272.005122] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.005441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.015366] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.015588] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.048731] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.049130] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.049426] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.049759] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:490] <7> [272.068105] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.068468] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [272.068967] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [272.069200] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [272.069416] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [272.069713] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.069920] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.070106] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.070325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.070514] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [272.070731] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.070897] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.071059] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.071250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [272.071527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [272.071806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [272.072035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [272.072260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [272.072467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [272.073421] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.073643] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.074062] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [272.074225] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [272.082228] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.115178] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.115640] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [272.115979] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [272.116274] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [272.116596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.116622] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.116884] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [272.117144] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.117198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [272.117508] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [272.117598] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.117901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [272.118331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [272.118834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [272.119289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [272.119720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [272.120141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [272.122484] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.122927] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.165290] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.165776] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.165880] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.166244] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [272.166401] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.166546] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [272.166905] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [272.166915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.167158] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [272.167403] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.167705] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.167971] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.168241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.168504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.168808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [272.169078] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [272.169299] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [272.169587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [272.170010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [272.170441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [272.170881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [272.171246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [272.171661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [272.173252] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.173646] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.181466] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [272.199244] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.199620] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.231912] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.232177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.232439] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [272.232769] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [272.232962] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [272.232902] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.233150] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [272.233258] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.233332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.233510] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [272.233576] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.233753] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [272.233988] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [272.234216] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.234433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.234656] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.234855] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.235085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [272.235412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [272.235777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [272.236066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [272.236351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [272.236688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [272.237801] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.238110] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.248803] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.248996] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.282495] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:491] <7> [272.282717] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.283177] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.283593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.303363] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.303710] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [272.303945] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [272.304126] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [272.304300] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [272.304462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.304686] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [272.304855] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [272.305035] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [272.305189] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [272.305330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.305460] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.305607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.305751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [272.305973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [272.306160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [272.306329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [272.306500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [272.306680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [272.307286] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.307445] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.307853] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [272.307985] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [272.315396] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.348439] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.348840] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [272.348811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.349127] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [272.349281] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.349369] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [272.349659] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.349673] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.349929] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [272.350170] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [272.350408] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [272.350727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [272.351103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [272.351472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [272.351884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [272.352247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [272.352637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [272.353698] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.354073] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.398487] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.398952] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.398985] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.399360] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [272.399466] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.399692] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [272.399964] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [272.399918] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.400219] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [272.400529] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.400850] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [272.401129] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [272.401405] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [272.401689] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.401922] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [272.402211] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [272.402451] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [272.402775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [272.403122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [272.403476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [272.403861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [272.404246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [272.404597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [272.405881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.406226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.414727] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [272.432232] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.432484] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.465042] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.465283] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.465567] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [272.465707] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.465791] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [272.465970] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [272.466047] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.466144] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [272.466316] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.466321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.466513] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [272.466741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [272.466919] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [272.467095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.467270] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [272.467450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [272.467667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [272.467868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [272.468135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [272.468397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [272.468683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [272.468978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [272.469236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [272.470254] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.470526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.481961] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.482161] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.515018] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.515319] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823 <7> [272.515590] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614 <7> [272.515706] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.515802] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614 <7> [272.516022] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [272.516122] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.516233] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.516444] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [272.516460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.516697] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [272.516921] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [272.517193] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.517416] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.517703] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.517937] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.518151] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.518366] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.518658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.518875] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.519081] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [272.519283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.519482] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.519745] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.519975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [272.520298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [272.520625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [272.520978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [272.521280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [272.521592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [272.522423] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.522745] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.523445] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [272.523728] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [272.531995] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.565086] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.565510] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [272.565972] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [272.566103] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.566255] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [272.566515] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.566613] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.566899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [272.567001] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.567168] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [272.567416] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [272.567761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [272.568137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [272.568516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [272.568949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [272.569378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [272.569785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [272.570723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.571079] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.615231] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.615721] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.615831] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.616185] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [272.616354] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.616505] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [272.616865] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [272.616872] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.617141] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [272.617414] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.617740] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.618006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.618268] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.618534] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.618773] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [272.619018] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [272.619313] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [272.619681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [272.620110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [272.620507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [272.620999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [272.621361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [272.621768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [272.623209] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.623604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.631386] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [272.649054] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.649394] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.681778] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.682110] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.682441] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [272.682849] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [272.683000] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.683111] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [272.683365] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [272.683475] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.683657] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.683926] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [272.683946] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.684174] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [272.684415] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [272.684714] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.684984] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.685230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.685472] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.685821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [272.686201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [272.686583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [272.686965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [272.687280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [272.687683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [272.688881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.689217] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.698676] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.698873] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.731884] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.732232] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823 <7> [272.732584] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614 <7> [272.732710] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.732828] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614 <7> [272.733064] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [272.733146] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.733345] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.733605] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.733551] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.733830] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.734055] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.734272] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [272.734487] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.734766] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.734993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.735243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [272.735617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [272.735979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [272.736316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [272.736690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [272.737074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [272.738412] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.738783] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.739541] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [272.739843] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [272.748559] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.781675] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.781989] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [272.782257] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [272.782467] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [272.782741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.782866] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.782948] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [272.783155] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [272.783244] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.783400] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [272.783586] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.783707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [272.784180] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.784410] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [272.784674] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [272.784853] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [272.785025] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.785230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [272.785410] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [272.786119] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [272.786332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [272.786687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [272.786971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [272.787244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [272.787527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [272.787801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [272.788651] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.788937] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.831741] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.832056] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.832404] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [272.832698] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [272.832921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [272.832838] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.833133] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [272.833242] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.833336] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.833560] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.833606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.833794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.833982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.834161] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.834337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [272.834527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [272.834700] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [272.834949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [272.835490] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.835781] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.836032] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [272.836208] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [272.836373] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [272.836573] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [272.836747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.836928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.837101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.837272] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.837442] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.837657] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [272.837867] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [272.838065] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [272.838251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [272.838555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [272.838845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [272.839116] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [272.839382] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [272.839661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [272.840788] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.841068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.848022] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [272.865362] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.865613] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.898440] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.898847] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.898973] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.899191] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [272.899450] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.899727] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [272.899928] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.900018] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [272.900268] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [272.900613] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.900898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [272.901150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [272.901395] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [272.901692] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.901964] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [272.902208] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [272.902453] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [272.902807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [272.903185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [272.903562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [272.903955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [272.904304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [272.904691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [272.906003] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.906349] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.915224] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.915410] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [272.948741] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.948672] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.949165] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826 <7> [272.949210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.949547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605 <7> [272.949688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.949826] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620 <7> [272.950087] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [272.950341] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [272.950695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [272.950925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [272.951154] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [272.951401] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [272.951680] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.951908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.952135] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [272.952402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [272.952835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [272.953208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [272.953565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [272.953902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [272.954232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [272.955419] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [272.955800] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [272.956640] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [272.956938] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [272.965199] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.998537] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [272.998680] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [272.999011] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [272.999175] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [272.999525] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [272.999602] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289 <7> [272.999935] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164 <7> [273.000254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.000597] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.000932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [273.001195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [273.001521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [273.001943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [273.002358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [273.002860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [273.003277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [273.003700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [273.004922] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.005339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.048465] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.048960] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.049380] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913 <7> [273.049827] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452 <7> [273.049973] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.050115] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794 <7> [273.050375] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892 <7> [273.050449] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.050719] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.050962] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.050917] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.051201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [273.051511] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [273.051750] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.051973] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.052198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [273.052419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [273.052817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [273.053208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [273.053594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [273.053979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [273.054339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [273.054788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [273.056211] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.056573] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.064630] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [273.082132] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.082399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.114983] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.115313] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.115719] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691 <7> [273.115811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.116015] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676 <7> [273.116276] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350 <7> [273.116286] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.116571] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334 <7> [273.116740] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.116879] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.117138] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.117388] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [273.117691] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [273.117934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.118172] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.118477] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [273.118807] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [273.119068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [273.119422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [273.119811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [273.120201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [273.120573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [273.120905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [273.122255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.122625] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.131920] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.132121] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.164895] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.165181] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 691) -> ( 0 - 823), size 691 -> 823 <7> [273.165383] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 691 - 1367) -> ( 823 - 2437), size 676 -> 1614 <7> [273.165646] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2717) -> (2437 - 4051), size 1350 -> 1614 <7> [273.165833] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0 <7> [273.165767] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.166006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.166098] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.166178] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.166347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.166375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.166583] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.166759] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [273.166938] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.167117] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.167292] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.167522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [273.167862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [273.168161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [273.168456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [273.168827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [273.169112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [273.169984] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.170286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.171066] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [273.171329] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [273.181884] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.214995] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.215318] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [273.215614] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [273.215823] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [273.215753] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.216022] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.216113] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.216211] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [273.216399] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [273.216398] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.216676] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [273.216953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [273.217421] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.217699] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [273.217909] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [273.218108] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [273.218316] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.218565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [273.218795] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [273.218998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [273.219206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [273.219544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [273.219899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [273.220211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [273.220535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [273.220894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [273.221741] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.222060] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.265021] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.265403] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.265714] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.265751] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.266032] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [273.266149] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.266245] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [273.266443] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [273.266462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.266691] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [273.266894] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.267097] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.267318] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.267584] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.267800] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.268007] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [273.268215] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [273.268421] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [273.268733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [273.269114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [273.269518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [273.269890] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [273.270261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [273.270669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [273.271939] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.272316] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.281299] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [273.299177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.299545] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.331632] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.331907] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.332173] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [273.332407] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [273.332688] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [273.332815] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.332908] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [273.333119] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.333220] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.333326] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [273.333606] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [273.333589] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.333844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [273.334045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.334246] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.334452] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.334716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.334953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [273.335498] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.335741] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.335984] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [273.336231] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [273.336427] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [273.336737] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [273.336947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.337154] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [273.337341] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [273.337562] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [273.337747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.337969] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.338169] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.338388] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.338627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [273.338946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [273.339273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [273.339601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [273.339901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [273.340194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [273.341158] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.341485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.348526] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.348719] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.381628] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.381920] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823 <7> [273.382158] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614 <7> [273.382350] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614 <7> [273.382595] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [273.382786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.382728] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.382973] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.383084] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.383172] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.383389] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.383374] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.383612] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [273.383788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.383965] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.384135] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.384332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [273.384692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [273.384958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [273.385220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [273.385484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [273.385743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [273.386891] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.387177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.387801] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [273.388076] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [273.398519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.431572] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.431912] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [273.432208] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [273.432498] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [273.432644] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.432747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.432972] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [273.433059] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.433211] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [273.433400] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.433453] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [273.433779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [273.434102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [273.434415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [273.434760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [273.435074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [273.435387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [273.436351] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.436707] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.481714] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.482078] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.482416] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [273.482764] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [273.482903] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.483006] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [273.483237] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [273.483341] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.483487] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.483713] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.483753] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.483939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.484196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.484408] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.484674] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [273.484879] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [273.485083] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [273.485322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [273.485721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [273.486060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [273.486402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [273.486784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [273.487117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [273.488772] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.489118] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.497920] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [273.515819] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.516293] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.548383] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.548897] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.548972] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.549316] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [273.549529] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.549745] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [273.549952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.550016] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [273.550273] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [273.550567] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.550813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [273.551091] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [273.551351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [273.551634] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.551877] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.552130] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.552370] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.552728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [273.553104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [273.553488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [273.553858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [273.554228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [273.554689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [273.556217] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.556618] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.565206] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.565414] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.598403] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.598771] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826 <7> [273.598855] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.599013] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605 <7> [273.599208] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620 <7> [273.599212] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.599395] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [273.599546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.599635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.599818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.600009] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [273.600228] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [273.600408] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [273.600633] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.600818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.601004] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.601243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [273.601601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [273.601904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [273.602218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [273.602614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [273.602928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [273.603959] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.604286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.605050] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [273.605335] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [273.615062] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.648172] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.648512] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [273.648617] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.648778] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289 <7> [273.648986] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164 <7> [273.648973] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.649196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.649284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.649402] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.649658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [273.649876] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [273.650179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [273.650566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [273.650894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [273.651210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [273.651546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [273.651879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [273.652742] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.653068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.698376] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.698939] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.699268] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.699700] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913 <7> [273.699786] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.700028] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452 <7> [273.700287] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794 <7> [273.700304] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.700580] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892 <7> [273.700747] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.700826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.701064] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.701328] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [273.701655] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [273.701887] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.702109] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.702337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [273.702615] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [273.702876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [273.703250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [273.703660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [273.704073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [273.704426] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [273.704848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [273.706263] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.706676] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.714521] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [273.732613] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.732997] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.764992] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.765255] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.765567] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691 <7> [273.765554] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.765839] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676 <7> [273.765943] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.766068] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350 <7> [273.766284] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334 <7> [273.766276] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.766536] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.766754] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.766991] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [273.767234] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [273.767462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.767677] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [273.767889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [273.768085] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [273.768319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [273.768647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [273.768984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [273.769270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [273.769595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [273.769878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [273.770986] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.771268] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.781896] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [273.782086] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [273.814825] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 691) -> ( 0 - 2026), size 691 -> 2026 <7> [273.815052] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 691 - 1367) -> (2026 - 4051), size 676 -> 2025 <7> [273.815238] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2717) -> ( 0 - 0), size 1350 -> 0 <7> [273.815417] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0 <7> [273.815668] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.815689] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.815859] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.816063] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.816042] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.816283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.816334] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.816508] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.816685] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.816870] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.817050] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.817230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [273.817406] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.817650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.817866] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.818071] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [273.818274] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.818493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.818686] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.818906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [273.819476] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 691) -> ( 0 - 2026), size 691 -> 2026 <7> [273.819661] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 691 - 1367) -> (2026 - 4051), size 676 -> 2025 <7> [273.819840] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2717) -> ( 0 - 0), size 1350 -> 0 <7> [273.820012] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0 <7> [273.820195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.820361] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.820576] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.820737] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.820897] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.821062] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.821230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.821402] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.821626] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [273.821781] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.821982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.822160] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.822323] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [273.822494] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.822644] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.822785] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.822935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [273.823187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [273.823458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [273.823706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [273.823982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [273.824238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [273.825063] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.825320] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.825945] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [273.826193] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:35:plane 1A] <7> [273.848016] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [273.848150] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [273.848239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.848320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [273.848401] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [273.848514] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [273.848608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [273.848646] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.848727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [273.848811] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.848847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [273.848936] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.848964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [273.849074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [273.849181] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [273.849557] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.849688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.881631] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [273.882098] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [273.882494] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [273.882628] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.882793] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [273.883067] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.883148] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.883322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.883624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.883588] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.883875] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.884115] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.884347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [273.884643] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [273.884874] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [273.885171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [273.885592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [273.885961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [273.886327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [273.886722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [273.887078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [273.888340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.888747] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.898396] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [273.931468] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [273.931769] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [273.931996] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [273.932194] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [273.932385] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.932695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [273.932811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.932901] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [273.933096] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [273.933191] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.933277] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.933481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.933513] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.933658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.933834] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.934043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [273.934353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [273.934656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [273.934924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [273.935197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [273.936048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [273.936927] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.937204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [273.948332] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [273.981529] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [273.981759] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [273.981963] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [273.982157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [273.982344] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [273.982582] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [273.982708] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [273.982777] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [273.982953] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [273.983036] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [273.983121] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.983287] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.983301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [273.983478] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [273.983674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [273.983977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [273.984239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [273.984507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [273.984762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [273.985014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [273.985777] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [273.986040] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.014749] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [274.014966] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [274.015135] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.015301] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [274.015527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [274.015541] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.015704] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [274.015872] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.015891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [274.016131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [274.016147] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.016373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [274.016646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.016936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.017174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [274.017904] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.018160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.048096] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.048344] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [274.048634] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [274.048811] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [274.048758] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.048977] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.049141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.049089] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.049306] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.049365] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.049534] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.049709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.049874] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [274.050040] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [274.050241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [274.050460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [274.050731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [274.050980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [274.051227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [274.051490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [274.051741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [274.052749] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.053002] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.064870] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.098076] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.098336] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [274.098585] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [274.098772] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [274.098707] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.098957] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.099059] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.099135] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [274.099311] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [274.099349] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.099563] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [274.099733] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.099888] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.100044] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.100196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.100371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [274.100657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [274.100929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [274.101196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.101524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.101803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [274.102882] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.103155] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.114956] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.148547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [274.148581] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.148788] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [274.148919] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.148983] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [274.149163] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.149190] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.149338] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.149546] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [274.149717] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [274.149909] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [274.150080] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.150249] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.150425] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.150619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [274.151067] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [274.151260] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [274.151448] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [274.151619] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.151787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.151987] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [274.152152] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [274.152316] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [274.152512] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.152719] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.152950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.153149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [274.153449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [274.153732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [274.153999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [274.154261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [274.154539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [274.155351] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.155624] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.181596] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [274.181906] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [274.182136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.182344] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.182623] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [274.182761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.182844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [274.183095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [274.183147] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.183495] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.183550] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [274.183751] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [274.183928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.184099] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.184294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [274.184499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [274.184678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [274.184930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [274.185167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [274.185402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.185720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.185937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [274.186608] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.186816] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.214865] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.215239] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [274.215617] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [274.215642] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.215855] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [274.216080] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.216045] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.216294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.216382] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.216544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [274.216756] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [274.216985] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.217187] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.217388] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [274.217641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [274.217925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [274.218382] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.218692] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [274.218876] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [274.219051] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [274.219266] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.219500] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.219712] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [274.219893] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [274.220066] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.220236] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.220448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [274.220651] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [274.220828] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [274.221117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [274.221416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [274.221693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [274.222029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [274.222283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [274.223395] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.223705] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.231447] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.264714] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.264996] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [274.265227] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [274.265465] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [274.265539] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.265661] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.265844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.265879] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.266022] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [274.266154] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.266222] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [274.266391] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.266613] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.266788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [274.266963] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [274.267169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [274.267686] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.267929] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [274.268130] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [274.268302] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [274.268492] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.268650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.268806] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [274.269006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [274.269199] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.269365] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.269578] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [274.269732] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [274.269889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [274.270189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [274.270456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [274.270712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.270969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.271282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [274.272335] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.272642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.281500] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.314720] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026 <7> [274.314952] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025 <7> [274.315159] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [274.315358] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.315619] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.315802] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.315767] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.316016] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.316099] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.316207] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [274.316373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.316435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.316622] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.316794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.316998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [274.317274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [274.317582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [274.317850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [274.318108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [274.318425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [274.319061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.319315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.348064] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [274.348261] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [274.348486] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.348667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [274.348623] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.348846] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [274.348972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.349057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [274.349263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.349294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [274.349628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [274.349884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [274.350142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.350413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.350719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [274.351389] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.351702] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.381431] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.381689] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [274.381865] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [274.382033] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [274.382194] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.382352] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.382613] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.382796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.382735] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.382971] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.383140] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [274.383086] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.383308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [274.383375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.383508] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [274.383700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [274.383957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [274.384216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [274.384522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [274.384759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [274.385007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [274.385886] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.386143] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.398175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.431376] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.431721] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [274.431982] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [274.432182] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [274.432373] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.432626] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [274.432750] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.432815] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [274.433024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [274.433102] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.433201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.433373] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.433386] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.433601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.433787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.433996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [274.434272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [274.434574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [274.434841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.435100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.435423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [274.436266] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.436549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.448286] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.481381] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [274.481667] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [274.481866] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [274.482055] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.482237] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.482450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.482574] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.482633] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.482845] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [274.482906] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.483030] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.483201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.483174] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.483368] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.483614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [274.483901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [274.484152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [274.484422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [274.484676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [274.484924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [274.485687] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.485957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.514676] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [274.514871] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [274.515053] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.515231] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [274.515447] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [274.515505] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.515626] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [274.515832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [274.515858] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.516093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [274.516177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.516346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [274.516644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.516950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.517204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [274.518002] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.518271] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.548000] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.548235] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [274.548444] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [274.548614] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [274.548571] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.548786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.548957] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.548918] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.549126] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.549211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.549323] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.549538] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.549701] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [274.549857] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [274.550012] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [274.550195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [274.550459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [274.550709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [274.550964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [274.551242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [274.551527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [274.552522] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.552778] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.564854] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.598012] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.598269] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [274.598555] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [274.598745] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [274.598693] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.598927] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.599107] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [274.599065] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.599285] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [274.599355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.599544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [274.599715] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.599874] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.600032] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.600188] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.600368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [274.600796] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.601015] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [274.601189] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [274.601360] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [274.601585] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.601751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [274.601940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [274.602101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [274.602260] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.602439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.602596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.602750] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.602931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [274.603185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [274.603446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [274.603722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.603976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.604232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [274.605241] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.605527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.615097] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.648225] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [274.648495] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [274.648523] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.648693] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [274.648884] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.648903] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.649075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.649193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.649267] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [274.649525] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [274.649710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [274.649879] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.650050] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.650217] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.650424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [274.650810] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [274.650995] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [274.651175] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [274.651347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.651580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.651752] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [274.651918] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [274.652081] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [274.652240] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.652419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.652580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.652751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [274.653028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [274.653280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [274.653559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [274.653822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [274.654083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [274.654859] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.655124] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.681447] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [274.681788] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [274.682034] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.682261] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.682602] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [274.682627] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.682822] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [274.683029] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.683079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [274.683367] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.683581] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [274.683794] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [274.683982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.684167] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.684353] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [274.684589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [274.684789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [274.685208] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [274.685426] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [274.685596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.685763] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.685964] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [274.686153] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [274.686332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [274.686620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [274.686872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [274.687104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.687332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.687577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [274.688249] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.688485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.714664] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.714966] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [274.715181] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [274.715415] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [274.715607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.715563] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.715787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.715904] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.715959] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [274.716160] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [274.716177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.716350] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.716561] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.716723] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [274.716891] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [274.717084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [274.717558] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.717764] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [274.717920] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [274.718071] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [274.718222] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.718392] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.718550] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [274.718737] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [274.718930] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.719088] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.719248] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [274.719431] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [274.719598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [274.719858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [274.720109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [274.720355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [274.720640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [274.720951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [274.721963] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.722212] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.731318] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.764651] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.764944] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [274.765203] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [274.765463] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [274.765660] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.765601] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.765843] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.765938] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.766022] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [274.766205] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.766231] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [274.766449] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.766618] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [274.766786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [274.766998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [274.767228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [274.767537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [274.767809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [274.768057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.768295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.769216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [274.770255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.770546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.781484] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.814677] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691 <7> [274.814948] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360 <7> [274.815187] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [274.815469] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.815607] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.815696] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [274.815903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [274.815989] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.816150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [274.816300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.816390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.816598] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.816786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.816964] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.817140] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [274.817343] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.817570] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.817741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [274.817949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [274.818251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [274.818580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [274.818871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.819138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [274.819415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [274.820167] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.820453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.864739] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [274.865014] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [274.865236] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.865501] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [274.865624] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.865706] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [274.865942] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [274.865994] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.866184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [274.866279] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.866489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [274.866760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [274.867030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.867293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [274.867606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [274.868299] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.868602] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.898438] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.898847] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.899137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.899408] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:492] <7> [274.918432] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.918749] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [274.918956] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [274.919148] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [274.919325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.919829] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.920025] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.920182] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.920328] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.920516] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [274.920670] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [274.920835] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [274.921012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [274.921218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [274.921421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [274.921606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [274.921788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [274.921967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [274.922635] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.922811] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.931776] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.964665] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [274.964933] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [274.965135] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [274.965329] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [274.965601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.965638] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [274.965789] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [274.965984] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [274.965996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [274.966191] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [274.966289] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [274.966405] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [274.966577] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [274.966747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [274.966909] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [274.967096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [274.967349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [274.967645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [274.967954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [274.968215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [274.968506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [274.969444] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [274.969730] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [274.981729] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.014637] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [275.014874] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [275.015083] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [275.015283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.015535] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.015727] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.015677] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.015945] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.016019] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.016140] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [275.016308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.016293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.016526] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.016707] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.016926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [275.017206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [275.017517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [275.017786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.018040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.018280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [275.019135] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.019442] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.048032] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [275.048340] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [275.048721] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.048721] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.049014] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [275.049133] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.049277] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [275.049530] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.049603] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [275.049951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [275.050405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [275.050847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [275.051254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [275.051689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [275.052106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [275.053255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.053637] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.081423] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.081827] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [275.082124] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [275.082427] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [275.082555] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.082670] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.082904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.082989] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.083141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.083403] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.083384] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.083628] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.083848] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [275.084073] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [275.084343] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [275.084655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [275.085165] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.085613] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [275.085825] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [275.086033] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [275.086237] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.086553] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.086755] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.086950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.087143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.087327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [275.087579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [275.087783] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [275.088042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [275.088396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [275.088738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [275.089129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.089539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.089888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [275.091109] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.091433] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.097997] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.131327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.131655] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [275.131880] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [275.132071] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [275.132254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.132484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [275.132615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.132666] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [275.132889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [275.132959] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.133075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.133258] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.133245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.133477] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.133673] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.133886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [275.134256] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.134548] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [275.134719] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [275.134894] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [275.135067] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.135237] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [275.135488] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [275.135674] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [275.135864] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.136018] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.136199] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.136370] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.136529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [275.136787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [275.137047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [275.137307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [275.137609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [275.137865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [275.138857] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.139133] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.148014] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.181484] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [275.181734] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [275.181943] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [275.182142] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.182336] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.182595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [275.182726] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.182788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [275.182984] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [275.183075] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.183168] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.183366] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.183390] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.183545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.183795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [275.184313] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [275.184568] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [275.184748] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [275.184924] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.185095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.185266] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [275.186127] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [275.186326] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [275.186539] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.186710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.186911] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.187107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [275.187403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [275.187666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [275.187942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.188200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.188491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [275.189211] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.189517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.214674] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [275.214959] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [275.215202] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.215487] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.215626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.215714] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [275.215979] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [275.216038] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.216251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [275.216410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.216633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [275.216951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [275.217233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [275.217600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [275.217911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [275.218698] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.218952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.247919] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.248176] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [275.248443] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [275.248637] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [275.248589] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.248831] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.249019] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.248980] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.249219] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [275.249292] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.249469] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [275.249643] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.249804] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.249965] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [275.250121] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [275.250303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [275.250608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [275.250871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [275.251128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.251462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.251726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [275.252793] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.253057] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.264749] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.297894] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.298174] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [275.298437] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [275.298642] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [275.298577] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.298826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.298924] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.299008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.299184] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [275.299194] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.299427] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [275.299607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.299814] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.300014] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [275.300189] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [275.300413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [275.300695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [275.300954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [275.301208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [275.301482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [275.301780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [275.302783] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.303041] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.314761] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.347961] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691 <7> [275.348235] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360 <7> [275.348537] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0 <7> [275.348685] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.348761] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.348969] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.349060] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.349195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.349404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.349458] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.349666] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [275.349871] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.350078] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.350279] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.350570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [275.350911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [275.351201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [275.351519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.351823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.352140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [275.352904] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.353205] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.381242] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [275.381530] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [275.381652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.381729] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.381916] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [275.381991] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.382105] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [275.382299] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [275.382273] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.382566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [275.382846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [275.383105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [275.383375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [275.383627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [275.383934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [275.384613] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.384900] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.414607] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.414903] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [275.415114] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [275.415316] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [275.415591] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.415791] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.415724] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.416029] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.416122] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.416234] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.416464] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.416502] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.416648] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [275.416839] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [275.417034] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [275.417257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [275.417633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [275.418048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [275.418418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.418826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.419145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [275.420168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.420543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.431426] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.464538] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.464822] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [275.465031] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [275.465227] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [275.465474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.465667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [275.465600] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.465850] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [275.465941] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.466057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [275.466214] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.466254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.466464] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.466631] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.466794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.466992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [275.467269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [275.467581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [275.467837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [275.468079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [275.468315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [275.469200] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.469518] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.481397] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.514598] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [275.514824] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [275.515032] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [275.515235] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.515484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.515612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.515677] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.515894] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.515954] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.516093] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [275.516222] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.516265] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.516480] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.516662] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.516874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [275.517296] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [275.517552] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [275.517735] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [275.517903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.518100] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.518290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.518497] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.518656] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [275.518816] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.518983] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.519146] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.519339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [275.519609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [275.519870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [275.520115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.520375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.520658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [275.521414] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.521679] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.548017] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [275.548306] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [275.548635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.548725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.548883] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [275.549111] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [275.549162] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.549442] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [275.549546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.549686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [275.550148] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [275.550419] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [275.550641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.550881] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [275.551079] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [275.551275] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [275.551536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [275.551850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [275.552117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [275.552371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [275.552616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [275.552860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [275.553636] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.553866] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.581090] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.581206] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [275.581272] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [275.581359] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [275.581368] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.581440] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.581518] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.581527] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.581595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.581670] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.581654] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.581737] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.581805] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [275.581873] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [275.581940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [275.582015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [275.582145] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.582223] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [275.582290] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [275.582381] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [275.582456] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.582524] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.582592] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.582659] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.582721] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.582777] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [275.582832] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [275.582886] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [275.582944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [275.583037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [275.583127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [275.583211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.583294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.583407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [275.583853] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.583952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.597782] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.631219] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.631548] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [275.631749] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [275.631939] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [275.632126] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.632398] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [275.632433] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.632619] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [275.632857] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [275.632838] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.633075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.633175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.633259] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.633504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.633688] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.633908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [275.634525] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.634779] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [275.634961] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [275.635136] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [275.635328] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.635504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [275.635682] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [275.635861] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [275.636042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.636232] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.636506] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.636695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.636879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [275.637166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [275.637519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [275.637794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [275.638106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [275.638460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [275.639595] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.639906] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.648125] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.681428] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [275.681663] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [275.681862] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [275.682048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.682229] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.682459] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [275.682586] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.682639] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [275.682859] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [275.682930] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.683054] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.683225] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.683253] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.683493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [275.683693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [275.683957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [275.684209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [275.684488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.684743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.685009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [275.685797] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.686093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.714565] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [275.714810] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [275.715023] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.715221] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.715479] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [275.715504] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.715672] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [275.715861] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.715895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [275.716178] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.716261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [275.716601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [275.716915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [275.717212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [275.717758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [275.718711] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.719020] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.747847] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.748168] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [275.748489] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [275.748627] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.748705] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [275.748901] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.748990] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.749090] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.749337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [275.749285] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.749526] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [275.749741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.749926] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.750118] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [275.750286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [275.750537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [275.750812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [275.751080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [275.751372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.751637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.751899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [275.752889] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.753165] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.764658] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.797785] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.798067] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [275.798349] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [275.798481] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.798551] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [275.798743] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.798829] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.798924] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.799102] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [275.799105] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.799325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [275.799526] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.799706] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.799883] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [275.800055] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [275.800255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [275.800606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [275.800869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [275.801120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [275.801385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [275.801681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [275.802672] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.802932] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.814590] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [275.847782] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [275.848051] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597 <7> [275.848246] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293 <7> [275.848503] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161 <7> [275.848689] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.848631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.848862] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.848970] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.849028] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.849190] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.849238] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.849381] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.849537] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.849721] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.849902] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.850060] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.850217] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [275.850434] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [275.850624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [275.850821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [275.851072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [275.851333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [275.851570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [275.851816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [275.852075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [275.853035] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.853292] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.864216] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:35:plane 1A] <7> [275.864785] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [275.864954] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [275.881615] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [275.914454] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [275.914700] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [275.914885] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [275.915064] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [275.915239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.915473] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [275.915652] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [275.915612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.915865] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [275.915941] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.916091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [275.916215] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.916368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [275.916627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [275.916877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.917126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [275.917405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [275.918086] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.919041] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.964674] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [275.965031] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [275.965392] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [275.965466] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [275.965627] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [275.965847] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [275.965879] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [275.966074] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [275.966245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [275.966314] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.966552] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [275.966774] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [275.966987] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [275.967197] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [275.967445] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [275.967653] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [275.967847] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [275.968071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [275.968393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [275.968706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [275.969011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.969359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [275.969665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [275.970915] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [275.971252] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [275.980856] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [275.998548] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [275.998812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.031247] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.031519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.031666] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.031763] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [276.032010] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [276.032014] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.032210] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [276.032343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.032437] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [276.032625] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.032802] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [276.032975] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [276.033176] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [276.033407] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.033568] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.033733] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.033910] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.034133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [276.034469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [276.034737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [276.035021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [276.035332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [276.035609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [276.036686] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.036942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.048261] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.048518] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.081334] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.081434] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.081605] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [276.081809] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [276.081784] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.082005] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [276.082069] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.082194] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [276.082411] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.082599] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.082786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.083006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.083198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [276.083404] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.083583] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.083759] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.083958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [276.084295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [276.084573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [276.084843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [276.085107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [276.085468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [276.086529] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.086807] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.087395] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [276.087629] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [276.097991] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.131113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.131452] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [276.131561] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.131728] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [276.131951] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [276.131944] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.132175] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.132272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.132450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [276.132693] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [276.132932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [276.133174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [276.133533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [276.133894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [276.134239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [276.134633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [276.134999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [276.135968] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.136345] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.181333] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.181734] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.182139] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [276.182453] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [276.182586] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.182694] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [276.182926] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [276.183027] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.183153] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.183417] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.183436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.183659] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.183872] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.184069] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.184258] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [276.184517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [276.184708] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [276.184942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [276.185259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [276.185625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [276.185934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [276.186241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [276.186596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [276.188041] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.188370] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.197463] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [276.214964] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.215230] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.247785] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.248035] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.248313] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [276.248429] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.248552] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [276.248746] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [276.248757] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.248933] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [276.249042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.249119] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.249325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [276.249520] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [276.249734] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [276.249908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.250080] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.250253] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.250479] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.250697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [276.250985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [276.251259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [276.251573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [276.251837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [276.252151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [276.253263] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.253586] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.264696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.264899] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.297887] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.298156] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [276.298405] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [276.298602] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [276.298540] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.298792] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [276.298886] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.298970] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.299145] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [276.299161] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.299351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [276.299525] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [276.299731] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [276.299926] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.300105] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.300298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.300500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [276.300819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [276.301099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [276.301397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [276.301722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [276.301981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [276.302927] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.303201] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.303880] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [276.304113] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [276.314627] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.347746] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.348015] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [276.348211] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [276.348469] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [276.348658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.348609] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.348850] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [276.348958] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.349040] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [276.349280] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [276.349251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.349499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [276.349837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [276.350137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [276.350524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [276.350814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [276.351122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [276.352079] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.352418] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.397854] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.398203] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.398616] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [276.398714] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.398851] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [276.399052] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [276.399102] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.399247] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [276.399493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.399469] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.399683] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [276.399871] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [276.400078] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [276.400299] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.400494] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [276.400659] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [276.400826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [276.401033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [276.401327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [276.401613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [276.401981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [276.402344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [276.402653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [276.404191] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.404539] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.414123] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [276.431705] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.431966] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.464393] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.464625] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.464857] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [276.465083] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [276.465313] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [276.465492] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [276.465449] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.465685] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.465778] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.465858] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [276.466040] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [276.466065] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.466272] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [276.466455] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.466636] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [276.466818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [276.466994] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [276.467194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [276.467504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [276.467776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [276.468040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [276.468372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [276.468629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [276.469844] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.470118] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.481513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.481721] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.514506] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.514768] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597 <7> [276.514967] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293 <7> [276.515150] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161 <7> [276.515372] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [276.515550] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.515513] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.515726] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.515840] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.515899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.516092] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.516106] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.516274] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [276.516440] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.516606] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.516767] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.516957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [276.517294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [276.517559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [276.517812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [276.518062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [276.518323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [276.519185] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.519484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.520118] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [276.520373] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [276.531318] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.564365] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.564647] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [276.564876] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [276.565073] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [276.565302] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.565313] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.565495] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [276.565686] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [276.565662] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.565920] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [276.565959] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.566178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [276.566720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.566974] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [276.567219] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [276.567478] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [276.567685] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.567890] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [276.568107] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [276.568377] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [276.568584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [276.568900] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [276.569213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [276.569566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [276.569922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [276.570227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [276.571087] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.571428] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.614515] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.614840] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.615160] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [276.615443] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [276.615574] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.615648] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [276.615876] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [276.615956] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.616067] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.616260] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.616276] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.616435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.616646] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.616828] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.616994] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [276.617159] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [276.617360] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [276.617558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [276.618055] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.618271] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.618471] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [276.618632] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [276.618791] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [276.618961] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [276.619138] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.619380] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.619555] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.619725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.619882] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.620035] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [276.620190] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [276.620399] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [276.620594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [276.620895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [276.621152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [276.621452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [276.621713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [276.621973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [276.623097] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.623427] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.630753] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [276.648022] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.648237] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.681007] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.681224] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.681506] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [276.681615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.681730] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [276.681924] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [276.681950] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.682096] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [276.682221] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.682281] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.682449] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [276.682634] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [276.682800] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [276.682971] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.683141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.683347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.683523] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.683719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [276.684011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [276.684277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [276.684526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [276.684775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [276.685053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [276.686064] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.686361] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.697888] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.698075] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.730999] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.731309] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [276.731296] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.731526] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [276.731669] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.731733] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [276.731927] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [276.731976] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.732111] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.732317] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.732537] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.732729] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.732903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [276.733075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.733259] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.733427] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.733621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [276.733893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [276.734164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [276.734456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [276.734731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [276.734988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [276.736022] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.736304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.736866] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [276.737108] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [276.747874] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.781002] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.781303] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [276.781409] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.781514] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [276.781715] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [276.781757] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.781904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.782035] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.782083] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [276.782283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [276.782461] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [276.782672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [276.782938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [276.783199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [276.783493] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [276.783748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [276.784007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [276.784804] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.785065] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.831129] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.831471] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.831777] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [276.831969] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [276.832144] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [276.832368] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [276.832540] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.832504] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.832710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.832851] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.832912] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.833084] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.833146] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.833273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.833442] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [276.833616] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [276.833796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [276.833981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [276.834265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [276.834519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [276.834766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [276.835023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [276.835292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [276.836675] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.836960] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.847362] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [276.864918] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.865204] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.897708] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.897966] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.898264] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [276.898477] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [276.898410] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.898679] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [276.898784] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.898881] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [276.899064] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.899081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.899273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [276.899497] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [276.899691] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [276.899903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.900085] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [276.900300] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [276.900475] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [276.900677] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [276.900947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [276.901217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [276.901527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [276.901805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [276.902060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [276.903206] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.903516] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.914640] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.914850] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [276.947780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.948050] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [276.948343] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [276.948368] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.948541] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [276.948734] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [276.948717] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.948917] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.949016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.949092] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [276.949292] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [276.949466] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [276.949673] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [276.949856] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.950027] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.950198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [276.950449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [276.950746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [276.951002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [276.951264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [276.951547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [276.951790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [276.952717] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [276.952968] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [276.953603] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [276.953845] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [276.964556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.997639] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.997902] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [276.998117] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [276.998358] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [276.998541] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [276.998482] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [276.998724] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [276.998818] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [276.998913] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [276.999125] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [276.999103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [276.999375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [276.999761] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [276.999984] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [277.000164] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [277.000381] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [277.000552] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.000720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.000931] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [277.001123] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [277.001343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [277.001615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [277.001866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [277.002113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [277.002393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [277.002658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [277.003393] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.003639] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.047751] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.048125] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.048470] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.048579] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.048757] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [277.048950] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [277.048927] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.049125] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [277.049196] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.049328] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [277.049495] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.049660] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.049825] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [277.050009] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [277.050177] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.050399] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.050567] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [277.050765] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [277.050959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [277.051244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [277.051516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [277.051780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [277.052077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [277.052358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [277.053487] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.053763] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.064019] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [277.081676] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.081940] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.114268] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.114487] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.114721] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [277.114918] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [277.115108] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [277.115339] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [277.115526] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.115480] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.115709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.115829] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.115931] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [277.116120] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [277.116116] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.116337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.116519] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.116699] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [277.116877] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [277.117123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [277.117669] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.117890] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.118105] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [277.118315] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [277.118486] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [277.118653] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [277.118852] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.119037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.119203] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [277.119431] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [277.119595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.119754] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.119911] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [277.120066] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [277.120249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [277.120495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [277.120744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [277.121010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [277.121261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [277.121549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [277.122638] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.122889] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.131351] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.131567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.164307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.164617] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823 <7> [277.164885] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614 <7> [277.165095] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614 <7> [277.165364] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [277.165481] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.165571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.165770] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [277.165856] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.165963] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [277.166151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.166186] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [277.166437] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.166643] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [277.166824] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [277.167000] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [277.167174] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.167393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [277.167561] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [277.167723] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [277.167885] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [277.168045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.168858] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.169024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.169228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [277.169507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [277.169784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [277.170053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [277.170376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [277.170641] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [277.171635] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.171913] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.172591] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [277.172836] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [277.181054] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.214248] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.214509] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [277.214706] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [277.214902] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [277.215095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.215330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [277.215450] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.215523] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [277.215725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [277.215801] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.215934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [277.216094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.216234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [277.216513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [277.216788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [277.217114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [277.217463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [277.218143] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.218458] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.264292] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.264574] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.264840] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [277.265031] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [277.265238] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [277.265412] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [277.265365] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.265582] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.265695] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.265783] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [277.265985] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [277.265999] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.266158] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [277.266383] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.266551] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [277.266714] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [277.266871] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [277.267053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [277.267341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [277.267596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [277.267865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [277.268134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [277.268427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [277.269403] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.269664] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.280651] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [277.298299] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.298602] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.330926] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.331175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.331506] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [277.331611] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.331770] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [277.331966] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [277.331977] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.332152] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [277.332298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.332388] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.332571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [277.332752] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [277.332964] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [277.333166] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.333421] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [277.333595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [277.333774] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [277.333991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [277.334361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [277.334653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [277.334953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [277.335268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [277.335620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [277.336671] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.336953] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.347816] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.348023] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.380909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.381179] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823 <7> [277.381507] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614 <7> [277.381540] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.381709] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614 <7> [277.381909] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [277.381893] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.382112] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.382224] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.382355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [277.382577] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [277.382818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [277.383072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [277.383318] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.383527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.383729] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.383951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [277.384267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [277.384562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [277.384860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [277.385158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [277.385511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [277.386611] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.386897] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.387527] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [277.387773] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [277.397711] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.430909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.431259] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [277.431261] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.431563] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [277.431657] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.431799] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [277.432010] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.431983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.432239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [277.432445] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [277.432690] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [277.432934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [277.433259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [277.433532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [277.433795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [277.434054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [277.434340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [277.435069] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.435381] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.481093] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.481538] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.481656] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.482014] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.481992] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.482427] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [277.482452] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.482698] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [277.482956] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [277.483226] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [277.483528] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.483757] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [277.484003] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [277.484286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [277.484535] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.484741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [277.484966] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [277.485204] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [277.485476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [277.485847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [277.486215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [277.486594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [277.486929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [277.487422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [277.489067] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.489441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.497261] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [277.515078] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.515477] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.547759] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.548074] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.548453] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [277.548549] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.548761] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [277.549018] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [277.548977] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.549305] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [277.549379] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.549594] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.549822] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [277.550042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [277.550294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [277.550530] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.550762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [277.550953] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [277.551213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [277.551482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [277.551795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [277.552110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [277.552462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [277.552794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [277.553073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [277.554305] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.554580] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.564720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.564934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.597839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.598273] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826 <7> [277.598264] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.598638] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605 <7> [277.598778] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.598922] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620 <7> [277.599205] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [277.599220] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.599461] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.599716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.599968] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [277.600286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [277.600538] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [277.600788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.601048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.601315] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.601611] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [277.602199] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.602480] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826 <7> [277.602699] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605 <7> [277.602911] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620 <7> [277.603122] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [277.603394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.603601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.603808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [277.604035] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [277.604309] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [277.604539] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.604775] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.605055] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.605325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [277.605731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [277.606092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [277.606450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [277.606823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [277.607215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [277.608420] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.608716] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.609414] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [277.609646] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [277.614477] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.647471] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.647735] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [277.647942] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289 <7> [277.648141] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164 <7> [277.648406] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.648601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.648553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.648796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [277.648901] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.649008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [277.649205] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.649224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [277.649487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [277.649747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [277.650019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [277.650324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [277.650629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [277.651334] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.651593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.697625] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.697934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.698319] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913 <7> [277.698371] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.698541] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452 <7> [277.698745] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794 <7> [277.698747] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.698929] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892 <7> [277.699032] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.699111] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.699330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.699509] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [277.699718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [277.699917] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.700085] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.700290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [277.700455] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [277.700657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [277.700930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [277.701215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [277.701540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [277.701803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [277.702069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [277.703456] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.703730] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.713920] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [277.731397] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.731646] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.764203] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.764329] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.764434] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.764679] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691 <7> [277.764677] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.764921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676 <7> [277.764965] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.765121] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350 <7> [277.765357] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334 <7> [277.765542] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.765724] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.765905] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [277.766127] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [277.766375] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.766556] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [277.766753] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [277.766970] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [277.767210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [277.767490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [277.767760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [277.768025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [277.768305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [277.768558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [277.769707] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.769975] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.781245] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.781480] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.814187] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.814456] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 691) -> ( 0 - 823), size 691 -> 823 <7> [277.814658] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 691 - 1367) -> ( 823 - 2437), size 676 -> 1614 <7> [277.814853] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2717) -> (2437 - 4051), size 1350 -> 1614 <7> [277.815042] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0 <7> [277.815278] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.815391] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.815465] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [277.815650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [277.815742] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.815871] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [277.816074] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [277.816037] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.816285] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.816464] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.816640] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [277.816847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [277.817120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [277.817420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [277.817742] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [277.818007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [277.818299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [277.819257] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.819528] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.820236] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [277.820468] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [277.831088] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.864251] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.864560] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [277.864818] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [277.865019] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [277.865251] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.865438] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [277.865375] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.865640] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [277.865729] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.865846] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [277.866024] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.866042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [277.866347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [277.866615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [277.866881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [277.867141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [277.867450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [277.868218] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.868484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.914339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.914683] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.915058] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [277.915382] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [277.915512] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.915625] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [277.915859] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [277.915971] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.916100] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.916420] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [277.916435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.916685] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [277.916928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [277.917136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.917413] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [277.917620] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [277.917823] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [277.918067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [277.918436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [277.918842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [277.919236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [277.919601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [277.919963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [277.921373] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.921750] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.930545] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [277.948028] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.948354] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.980954] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.981260] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [277.981393] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [277.981551] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [277.981836] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [277.981793] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [277.982043] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [277.982110] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [277.982288] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [277.982493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.982709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [277.982894] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [277.983077] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [277.983305] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [277.983518] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [277.983701] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [277.983892] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [277.984112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [277.984454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [277.984748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [277.985037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [277.985375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [277.985733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [277.986854] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [277.987177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [277.997928] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [277.998178] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [278.030945] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.031235] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823 <7> [278.031340] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.031440] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614 <7> [278.031634] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614 <7> [278.031691] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.031823] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [278.031996] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.031983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.032195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.032368] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.032570] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.032751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [278.032919] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.033093] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.033355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.033554] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [278.033835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [278.034095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [278.034375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [278.034672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [278.034928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [278.035995] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.036284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.036863] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [278.037103] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [278.047661] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.080780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.081063] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [278.081332] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [278.081535] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [278.081480] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.081722] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.081823] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.081901] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [278.082077] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [278.082092] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.082320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [278.082520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [278.082970] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.083207] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [278.083415] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [278.083590] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [278.083763] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.083926] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [278.084090] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [278.084289] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [278.084462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [278.084747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [278.085001] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [278.085275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [278.085567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [278.085811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [278.086519] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.086772] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.130923] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.131339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [278.131448] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.131663] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [278.131912] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [278.131851] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.132176] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [278.132252] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.132409] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [278.132635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.132906] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.133136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.133447] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.133659] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.133865] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [278.134072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [278.134331] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [278.134624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [278.135232] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.135495] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [278.135813] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [278.136036] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [278.136286] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [278.136492] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [278.136698] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.136943] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.137188] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.137389] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.137585] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.137777] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [278.137998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [278.138196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [278.138386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [278.138689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [278.138984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [278.139296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [278.139621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [278.139914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [278.141449] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.141740] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.147193] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [278.164639] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.164873] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [278.197409] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.197642] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [278.197882] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [278.198101] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [278.198347] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [278.198526] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [278.198492] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.198706] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.198889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [278.198842] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.199070] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [278.199125] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.199306] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [278.199487] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.199662] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.199831] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.200001] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.200217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [278.200479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [278.200736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [278.201002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [278.201289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [278.201584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [278.202661] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.202924] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.214421] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.214620] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [278.247569] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.247817] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826 <7> [278.248022] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605 <7> [278.248268] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620 <7> [278.248461] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [278.248410] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.248649] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.248762] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.248833] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.249028] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [278.249070] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.249313] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [278.249507] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [278.249722] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.249900] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.250078] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.250340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [278.250663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [278.250941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [278.251213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [278.251477] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [278.251732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [278.252718] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.252981] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.253632] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [278.253856] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [278.264317] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.297383] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.297648] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [278.297849] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289 <7> [278.298051] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164 <7> [278.298303] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.298499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.298434] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.298707] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [278.298788] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.298925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [278.299067] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.299158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [278.299425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [278.299689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [278.299965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [278.300273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [278.300547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [278.301307] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.301587] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.347512] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.347837] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [278.348211] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913 <7> [278.348297] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.348434] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452 <7> [278.348635] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794 <7> [278.348674] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.348820] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892 <7> [278.349001] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.348964] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.349213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.349392] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [278.349604] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [278.349795] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.349981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.350155] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [278.350309] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [278.350498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [278.350752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [278.351016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [278.351316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [278.351632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [278.351879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [278.353181] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.353460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.363811] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [278.381316] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.381599] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [278.414092] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.414413] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [278.414701] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691 <7> [278.414946] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676 <7> [278.415190] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350 <7> [278.415397] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334 <7> [278.415330] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.415600] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.415703] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.415805] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.415992] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [278.415994] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.416208] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [278.416391] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.416575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.416759] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [278.416939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [278.417158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [278.417428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [278.417700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [278.417962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [278.418308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [278.418580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [278.419665] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.419937] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.431089] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [278.431347] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [278.464267] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 691) -> ( 0 - 2018), size 691 -> 2018 <7> [278.464478] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 691 - 1367) -> (2018 - 4051), size 676 -> 2033 <7> [278.464666] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2717) -> ( 0 - 0), size 1350 -> 0 <7> [278.464848] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0 <7> [278.465037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.465281] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.465471] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [278.465416] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.465698] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [278.465771] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.465889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.466070] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.466064] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.466298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.466495] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.466718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [278.466930] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.467113] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.467343] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.467522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [278.467697] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.467868] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.468038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.468275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [278.468549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [278.468818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [278.469072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [278.469369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [278.469644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [278.470499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.470768] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.471387] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [278.471605] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:35:plane 1A] <7> [278.497477] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [278.497729] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [278.497928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.498114] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [278.498366] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [278.498485] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.498545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [278.498776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [278.498822] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.499168] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [278.499113] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.499351] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [278.499531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.499703] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [278.499892] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [278.500062] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [278.500285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [278.500558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [278.500827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [278.501092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [278.501374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [278.501600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [278.502246] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.502472] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.530916] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.531418] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [278.531393] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.531720] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [278.531791] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.531948] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [278.532203] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.532262] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.532481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.532695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.532950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.533218] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.533420] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [278.533615] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [278.533812] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [278.534034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [278.534519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.534783] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [278.535027] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [278.535281] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [278.535483] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.535720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.535943] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.536185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.536371] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.536552] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [278.536734] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [278.536910] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [278.537086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [278.537421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [278.537760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [278.538062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [278.538373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [278.538705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [278.539632] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.539925] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.547421] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.580689] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.580985] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [278.581283] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [278.581410] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.581501] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [278.581708] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.581785] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.581913] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [278.582128] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [278.582090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.582328] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [278.582568] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.582770] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.582980] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.583239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.583463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [278.583940] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.584184] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [278.584399] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [278.584574] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [278.584741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.584899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [278.585056] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [278.585291] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [278.585462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.585613] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.585771] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.585931] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.586102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [278.586416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [278.586682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [278.586948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [278.587240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [278.587525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [278.588455] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.588721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.597460] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.630822] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2018), size 1606 -> 2018 <7> [278.631175] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1606 - 2432) -> (2018 - 4051), size 826 -> 2033 <7> [278.631298] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.631440] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0 <7> [278.631688] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.631738] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.631937] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.632235] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.632180] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.632517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.632763] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [278.632989] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.633275] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.633505] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.633771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [278.634138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [278.634490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [278.634839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [278.635229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [278.635565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [278.636596] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.636944] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.664131] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [278.664432] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [278.664678] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.664898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [278.665136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [278.665281] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.665395] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [278.665623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [278.665658] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.665940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [278.665993] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.666294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [278.666606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [278.666891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [278.667183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [278.668142] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.668466] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.697383] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.697655] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [278.697849] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [278.698037] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [278.698283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.698476] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.698435] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.698674] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.698862] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.698807] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.699024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.699095] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.699227] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [278.699424] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [278.699585] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [278.699772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [278.700060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [278.700366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [278.700630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [278.700886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [278.701141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [278.702167] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.702454] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.714352] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.747402] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.747742] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [278.748038] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [278.748348] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [278.748486] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.748573] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.748796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [278.748895] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.749037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [278.749274] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.749349] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [278.749581] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.749801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.750007] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.750251] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.750517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [278.750865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [278.751207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [278.751529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [278.751838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [278.752145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [278.753404] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.753732] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.764423] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.797537] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2026), size 1606 -> 2026 <7> [278.797774] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1606 - 2432) -> (2026 - 4051), size 826 -> 2025 <7> [278.797978] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0 <7> [278.798232] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.798432] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.798370] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.798629] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [278.798723] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.798863] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [278.799006] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.799082] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [278.799349] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.799537] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.799717] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.799923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [278.800219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [278.800509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [278.800793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [278.801058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [278.801349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [278.802176] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.802467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.830767] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [278.831065] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [278.831404] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.831537] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.831635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.831857] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [278.831933] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.832117] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [278.832293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.832358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [278.832655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [278.832950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [278.833284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [278.833573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [278.833866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [278.834896] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.835228] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.864053] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.864416] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2310), size 1354 -> 2310 <7> [278.864636] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1354 - 4051) -> (2310 - 2894), size 2697 -> 584 <7> [278.864844] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2894 - 4051), size 0 -> 1157 <7> [278.865048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.865317] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.865458] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.865562] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [278.865763] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [278.865865] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.865947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.866143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.866205] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.866320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [278.866492] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [278.866685] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [278.866955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [278.867257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [278.867526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [278.867838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [278.868138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [278.869353] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.869657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.880949] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.914056] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.914457] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618 <7> [278.914739] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817 <7> [278.914993] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616 <7> [278.915379] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.915428] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.915624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.915871] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [278.915863] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.916122] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [278.916277] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.916351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.916574] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.916792] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [278.917040] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [278.917342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [278.917831] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.918144] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618 <7> [278.918421] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817 <7> [278.918648] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616 <7> [278.918850] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.919045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.919302] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [278.919504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [278.919702] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.919903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [278.920136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [278.920343] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [278.920561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [278.920882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [278.921207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [278.921556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [278.921861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [278.922153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [278.923257] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.923551] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.930909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [278.964215] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2018), size 1618 -> 2018 <7> [278.964545] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1618 - 2435) -> (2018 - 4051), size 817 -> 2033 <7> [278.964828] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0 <7> [278.965180] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.965288] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.965503] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.965760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.965762] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.966031] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.966225] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.966358] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [278.966628] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.966876] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.967144] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.967489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [278.968050] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2018), size 1618 -> 2018 <7> [278.968379] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1618 - 2435) -> (2018 - 4051), size 817 -> 2033 <7> [278.968632] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0 <7> [278.968885] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.969201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [278.969457] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [278.969733] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [278.969971] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [278.970246] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.970490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.970732] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [278.971033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [278.971454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [278.971853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [278.972195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [278.972526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [278.972892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [278.973763] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [278.974054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [278.997431] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [278.997727] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [278.997981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [278.998294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [278.998532] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [278.998451] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [278.998812] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [278.998902] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [278.999070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [278.999306] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [278.999613] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [278.999853] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [279.000063] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.000321] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [279.000517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [279.000712] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [279.000917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [279.001347] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [279.001539] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [279.001700] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.001855] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [279.002004] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [279.002185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [279.002345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [279.002588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [279.002833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [279.003064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.003318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.003558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [279.004226] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.004436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.030701] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.031148] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [279.031266] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.031435] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [279.031690] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [279.031705] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.031941] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.032141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.032245] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.032527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.032805] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.033047] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.033352] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [279.033575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [279.033786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [279.034037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [279.034658] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.034914] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [279.035129] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [279.035345] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [279.035547] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.035725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.035904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.036079] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.036306] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.036484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [279.036635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [279.036782] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [279.036939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [279.037223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [279.037461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [279.037698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [279.037987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [279.038230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [279.038985] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.039613] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.047425] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.080711] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.081050] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [279.081385] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [279.081514] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.081624] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [279.081853] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.081928] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.082075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [279.082306] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.082367] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [279.082595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [279.082807] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.083013] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.083272] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.083503] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.083734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [279.084060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [279.084438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [279.084763] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.085092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.085411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [279.086431] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.086761] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.097643] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.130678] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2018), size 1606 -> 2018 <7> [279.130979] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1606 - 2432) -> (2018 - 4051), size 826 -> 2033 <7> [279.131309] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0 <7> [279.131441] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.131567] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.131802] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.131866] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.132024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.132253] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.132321] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.132534] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [279.132748] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.132962] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.133220] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.133466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [279.133818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [279.134147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [279.134526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [279.134836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [279.135171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [279.136153] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.136489] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.164167] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [279.164241] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.164539] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [279.164716] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.164827] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.165116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [279.165144] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.165362] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [279.165655] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [279.165929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [279.166324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [279.166668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [279.166979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.167313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.167683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [279.168662] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.168990] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.197338] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.197659] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [279.197891] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [279.198133] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [279.198256] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.198332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.198522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.198606] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.198711] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.198908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.198900] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.199102] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.199280] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [279.199456] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [279.199667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [279.199857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [279.200128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [279.200384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [279.200661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [279.200930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [279.201231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [279.202331] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.202619] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.214320] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.247333] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.247633] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [279.247850] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [279.248065] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [279.248355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.248485] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.248561] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [279.248765] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [279.248862] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.248992] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [279.249226] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.249229] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.249419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.249612] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.249831] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.250041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [279.250373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [279.250656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [279.250903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.251175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.251476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [279.252588] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.252862] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.264290] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.297464] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2026), size 1606 -> 2026 <7> [279.297699] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1606 - 2432) -> (2026 - 4051), size 826 -> 2025 <7> [279.297896] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0 <7> [279.298133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.298330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.298263] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.298523] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.298617] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.298731] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.298907] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [279.298898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.299097] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.299271] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.299441] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.299637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [279.299911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [279.300222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [279.300555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [279.300832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [279.301118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [279.301904] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.302204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.330636] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [279.330905] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [279.331235] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.331329] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.331435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.331643] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [279.331683] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.331868] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [279.331985] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.332125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [279.332414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [279.332696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [279.332967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.333268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.333584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [279.334490] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.334779] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.364028] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.364437] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2310), size 1354 -> 2310 <7> [279.364534] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.364679] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1354 - 4051) -> (2310 - 2894), size 2697 -> 584 <7> [279.364911] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2894 - 4051), size 0 -> 1157 <7> [279.364977] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.365177] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.365397] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.365402] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.365621] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [279.365885] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [279.366162] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.366393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.366607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [279.366810] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [279.367047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [279.367584] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.367845] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2310), size 1354 -> 2310 <7> [279.368138] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1354 - 4051) -> (2310 - 2894), size 2697 -> 584 <7> [279.368382] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2894 - 4051), size 0 -> 1157 <7> [279.368615] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.368819] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.369023] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [279.369299] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [279.369536] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.369727] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.369909] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [279.370112] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [279.370341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [279.370674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [279.371020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [279.371452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [279.371778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [279.372092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [279.373263] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.373549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.380753] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.414032] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.414437] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618 <7> [279.414520] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.414685] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817 <7> [279.414906] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616 <7> [279.414916] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.415152] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.415282] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.415357] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.415564] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.415760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.415939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.416151] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.416330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.416505] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.416711] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [279.417186] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.417468] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618 <7> [279.417687] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817 <7> [279.417897] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616 <7> [279.418138] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.418349] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.418569] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.418768] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.418951] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.419157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.419355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.419524] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.419709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [279.419999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [279.420319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [279.420618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.420884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.421191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [279.422350] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.422655] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.430729] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.464026] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2687), size 1618 -> 2687 <7> [279.464451] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1618 - 2435) -> (2687 - 4051), size 817 -> 1364 <7> [279.464578] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.464744] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0 <7> [279.465024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.465103] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.465497] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.465559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.465852] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [279.466222] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [279.466461] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.466698] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.466946] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.467239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.467482] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [279.467720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.468001] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.468309] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.468602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [279.469247] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2687), size 1618 -> 2687 <7> [279.469488] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1618 - 2435) -> (2687 - 4051), size 817 -> 1364 <7> [279.469703] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0 <7> [279.469982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.470282] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.470556] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [279.470784] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [279.471050] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.471325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.471571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.471764] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.471961] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [279.472195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.472380] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.472562] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.472756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [279.473067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [279.473354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [279.473634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.473933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.474224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [279.475070] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.475318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.514009] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [279.514371] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [279.514613] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.514842] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [279.515122] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [279.515277] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.515380] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [279.515674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [279.515716] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.516018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [279.516093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.516378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [279.516744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.517068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.517429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [279.518314] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.518637] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.547663] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:493] <7> [279.548226] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.548641] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.548954] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.567136] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.567480] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907 <7> [279.567734] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392 <7> [279.567937] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752 <7> [279.568546] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.568786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.568993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.569243] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.569438] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.569624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [279.569800] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [279.569967] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [279.570197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [279.570462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [279.570722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [279.570982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [279.571273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [279.571591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [279.572516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.572770] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.580935] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.613934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.614371] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [279.614423] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.614668] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [279.614916] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [279.614865] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.615206] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.615272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.615444] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [279.615681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [279.615942] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [279.616213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.616433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.616654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.616878] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.617201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [279.617553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [279.617900] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [279.618285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [279.618662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [279.618992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [279.620080] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.620412] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.630808] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.663901] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687 <7> [279.664197] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364 <7> [279.664329] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.664412] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [279.664617] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.664688] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.664815] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.664967] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.664997] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.665262] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.665448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [279.665656] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.665839] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.666088] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.666331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [279.666634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [279.666934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [279.667260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.667595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.667879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [279.668699] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.668989] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.697313] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [279.697591] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [279.697814] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.698010] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [279.698269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [279.698470] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [279.698405] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.698679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [279.698757] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.698959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [279.699073] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.699259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [279.699529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.699795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.700134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [279.700993] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.701312] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.730506] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.730761] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907 <7> [279.730978] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392 <7> [279.731231] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752 <7> [279.731411] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.731389] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.731585] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.731751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.731744] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.731950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.732080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.732172] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.732364] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [279.732535] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [279.732693] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [279.732876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [279.733168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [279.733437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [279.733699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [279.733959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [279.734251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [279.735267] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.735546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.747434] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.780588] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.780892] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [279.781178] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [279.781386] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [279.781344] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.781589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.781787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [279.781750] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.781977] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [279.782103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.782273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [279.782460] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.782641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.782821] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.782990] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.783253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [279.783599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [279.783898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [279.784221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [279.784495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [279.784767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [279.785857] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.786175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.797513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.830781] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697 <7> [279.831083] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354 <7> [279.831215] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.831312] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [279.831529] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.831594] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.831736] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.831901] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.831934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.832185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.832371] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [279.832557] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.832738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.832936] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.833170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [279.833551] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697 <7> [279.833731] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354 <7> [279.833903] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [279.834098] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.834272] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.834464] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.834671] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.834845] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [279.835017] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.835256] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.835468] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.835653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [279.835927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [279.836210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [279.836499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.836749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [279.837011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [279.837837] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.838133] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.863989] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [279.864335] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [279.864452] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.864565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.864775] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.864828] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.864977] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [279.865191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.865276] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [279.865537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [279.865999] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [279.866257] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [279.866447] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.866666] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.866867] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [279.867084] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [279.867333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [279.867632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [279.867916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [279.868226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.868511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [279.868766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [279.869546] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.869801] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.897334] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.897673] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936 <7> [279.897905] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376 <7> [279.898182] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739 <7> [279.898390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.898333] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.898591] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.898713] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.898788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [279.898993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [279.899063] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.899240] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.899428] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.899621] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [279.899795] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [279.899993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [279.900458] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.900674] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936 <7> [279.900846] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376 <7> [279.901009] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739 <7> [279.901223] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.901380] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.901542] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [279.901712] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [279.901872] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.902050] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.902216] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [279.902381] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [279.902552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [279.902821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [279.903128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [279.903466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [279.903748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [279.904053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [279.905134] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.905416] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.913941] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.947191] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.947500] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2936) -> ( 0 - 2306), size 2936 -> 2306 <7> [279.947778] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2936 - 3312) -> (2306 - 2893), size 376 -> 587 <7> [279.947979] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3312 - 4051) -> (2893 - 4051), size 739 -> 1158 <7> [279.948239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.948359] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.948434] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.948623] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.948712] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.948819] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.948989] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.948992] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.949204] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.949375] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.949543] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.949741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [279.950239] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.950477] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2936) -> ( 0 - 2306), size 2936 -> 2306 <7> [279.950698] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2936 - 3312) -> (2306 - 2893), size 376 -> 587 <7> [279.950887] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3312 - 4051) -> (2893 - 4051), size 739 -> 1158 <7> [279.951121] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.951359] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.951578] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.951763] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.951935] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.952134] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [279.952311] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [279.952481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [279.952664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [279.952928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [279.953226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [279.953525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [279.953796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [279.954101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [279.955174] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [279.955443] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [279.964000] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [279.997216] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2306) -> ( 0 - 2687), size 2306 -> 2687 <7> [279.997480] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2306 - 2893) -> (2687 - 4051), size 587 -> 1364 <7> [279.997704] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2893 - 4051) -> ( 0 - 0), size 1158 -> 0 <7> [279.997906] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [279.998146] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [279.998284] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [279.998340] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [279.998570] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [279.998639] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [279.998777] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [279.998947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.998922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [279.999149] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.999316] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [279.999547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [279.999830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [280.000133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [280.000408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [280.000681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [280.000941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [280.001654] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.001925] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.030564] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [280.030827] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [280.031088] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.031289] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.031228] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.031482] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.031587] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.031709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.031880] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.031951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [280.032296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [280.032579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [280.032842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [280.033131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [280.033386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [280.034133] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.034416] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.063812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.064108] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907 <7> [280.064206] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.064320] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392 <7> [280.064498] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752 <7> [280.064559] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.064671] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.064841] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.064849] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.065052] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.065255] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.065426] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.065584] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [280.065744] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [280.065904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [280.066121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [280.066389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [280.066666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [280.066931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.067222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.067518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [280.068345] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.068625] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.080560] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.114084] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.114162] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.114429] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [280.114536] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.114656] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [280.114861] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [280.114850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.115098] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.115290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.115527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.115725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.115899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.116091] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.116257] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.116419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.116615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [280.116882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [280.117159] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [280.117409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [280.117655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [280.117922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [280.118972] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.119316] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.130718] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.163878] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687 <7> [280.164239] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364 <7> [280.164373] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.164498] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [280.164742] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.164810] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.164981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.165283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.165260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.165541] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.165787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [280.166024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.166247] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.166462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.166718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [280.167080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [280.167480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [280.167822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [280.168203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [280.168597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [280.169541] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.169892] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.197219] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [280.197501] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [280.197729] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.197943] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.198226] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.198343] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.198430] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.198665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [280.198715] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.198968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [280.199056] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.199307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [280.199598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [280.199936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [280.200377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [280.201428] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.201730] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.230516] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.230883] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907 <7> [280.231285] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392 <7> [280.231389] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.231547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752 <7> [280.231767] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.231795] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.231978] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.232186] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.232248] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.232479] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.232687] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.232889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [280.233124] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [280.233320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [280.233545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [280.233870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [280.234221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [280.234538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.234853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.235184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [280.236397] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.236722] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.247463] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.280507] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.280882] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [280.281224] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [280.281363] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.281480] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [280.281724] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.281801] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.282021] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.282194] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.282269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.282497] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.282712] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.282925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.283190] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.283426] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.283661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [280.284132] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.284398] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [280.284611] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [280.284816] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [280.285045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.285241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.285435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.285629] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.285818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.286045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.286238] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.286423] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.286621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [280.286953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [280.287880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [280.288232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [280.288535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [280.288873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [280.289983] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.290313] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.297387] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.330823] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697 <7> [280.331165] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354 <7> [280.331288] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.331411] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [280.331642] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.331692] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.331872] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.332116] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.332176] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [280.332410] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [280.332649] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [280.332867] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.333144] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.333352] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.333588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [280.334135] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697 <7> [280.334362] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354 <7> [280.334570] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [280.334798] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.335033] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.335242] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [280.335440] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [280.335634] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [280.335826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.336070] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.336264] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.336460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [280.336780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [280.337108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [280.337431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [280.337734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [280.338073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [280.338956] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.339291] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.363833] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [280.364176] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [280.364222] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.364414] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.364640] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.364654] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.364860] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [280.364992] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.365137] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [280.365386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [280.365869] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [280.366141] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [280.366337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.366533] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.366718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [280.366943] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [280.367195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [280.367608] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [280.367774] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [280.367933] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.368169] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.368335] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [280.368474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [280.368634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [280.368867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [280.369122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [280.369370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [280.369585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [280.369824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [280.370476] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.370674] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.397223] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.397621] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936 <7> [280.397908] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376 <7> [280.398275] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739 <7> [280.398412] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.398548] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.398808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.398887] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.399151] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [280.399343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.399425] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [280.399673] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.399912] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.400219] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [280.400481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [280.400756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [280.401425] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.401703] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936 <7> [280.401921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376 <7> [280.402170] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739 <7> [280.402362] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.402550] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.402744] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [280.402939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [280.403170] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.403367] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.403545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [280.403720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [280.403939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [280.404275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [280.404532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [280.404796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.405081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.405302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [280.406228] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.406458] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.413814] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.447133] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.447469] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2936) -> ( 0 - 2306), size 2936 -> 2306 <7> [280.447742] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2936 - 3312) -> (2306 - 2893), size 376 -> 587 <7> [280.447958] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3312 - 4051) -> (2893 - 4051), size 739 -> 1158 <7> [280.448234] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.448440] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.448373] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.448661] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [280.448751] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.448868] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [280.449092] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.449100] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.449285] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.449477] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [280.449667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [280.449874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [280.450192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [280.450511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [280.450786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [280.451061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [280.451315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [280.452392] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.452674] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.464154] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [280.497183] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.497580] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2306) -> ( 0 - 583), size 2306 -> 583 <7> [280.497896] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2306 - 2893) -> ( 583 - 2898), size 587 -> 2315 <7> [280.498240] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2893 - 4051) -> (2898 - 4051), size 1158 -> 1153 <7> [280.498376] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.498490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.498731] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.498814] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.498967] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [280.499282] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [280.499248] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.499514] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.499776] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.500028] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.500252] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.500471] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.500688] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.500932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 4, 8, 8, 8, 8, 8, 0, 0, 19, 4, 19 <7> [280.501433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [280.501701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [280.502128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [280.502465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [280.502798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [280.503203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [280.503533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [280.504744] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.505097] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.513465] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:35:plane 1A] <7> [280.514075] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [280.514236] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [280.530966] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.563798] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.564127] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [280.564169] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.564339] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939 <7> [280.564540] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737 <7> [280.564548] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.564737] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.564855] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.564923] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.565158] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.565339] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.565585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [280.565866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [280.566146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [280.566401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.566650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.566912] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [280.567723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.568040] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.613887] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.614332] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [280.614715] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673 <7> [280.615027] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692 <7> [280.615168] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.615292] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333 <7> [280.615573] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353 <7> [280.615649] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.615826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.616078] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.616116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.616397] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.616636] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.616868] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.617143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [280.617371] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [280.617596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [280.617916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [280.618338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [280.618682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [280.619031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [280.619423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [280.619816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [280.621232] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.621582] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.630089] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [280.647644] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.647943] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [280.680528] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.680943] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [280.681483] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.681518] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452 <7> [280.681919] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913 <7> [280.682005] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.682316] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893 <7> [280.682423] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.682619] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793 <7> [280.682917] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.683290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.683616] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.683904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.684265] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.684552] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.684842] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.685194] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.685570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [280.686014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [280.686436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [280.686847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [280.687297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [280.687707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [280.689295] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.689705] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.697383] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.697574] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [280.730418] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.730745] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 452) -> ( 0 - 583), size 452 -> 583 <7> [280.731024] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 452 - 1365) -> ( 583 - 2898), size 913 -> 2315 <7> [280.731254] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2258) -> (2898 - 4051), size 893 -> 1153 <7> [280.731175] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.731485] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0 <7> [280.731582] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.731697] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.731907] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.731920] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.732172] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.732382] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.732636] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [280.732839] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.733075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.733275] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.733556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [280.733891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [280.734249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [280.734610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [280.734907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [280.735282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [280.736558] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.736886] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.737625] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [280.737914] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [280.747296] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.780461] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.780822] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [280.781209] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939 <7> [280.781343] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.781465] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737 <7> [280.781715] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.781781] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.781947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.782171] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.782224] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.782493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.782775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [280.783272] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.783536] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [280.783778] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939 <7> [280.784007] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737 <7> [280.784217] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.784423] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.784652] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.784859] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.785123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [280.785438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [280.785761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [280.786102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.786458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.786768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [280.787745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.788112] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.830504] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.830945] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.831307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [280.831436] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.831617] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673 <7> [280.831865] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692 <7> [280.831846] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.832162] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333 <7> [280.832265] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.832396] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353 <7> [280.832624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.832848] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.833155] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.833419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.833656] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.833873] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [280.834141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [280.834353] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [280.834597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [280.834947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [280.835344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [280.835693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [280.836039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [280.836420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [280.837812] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.838223] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.846735] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [280.864514] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.864824] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [280.897049] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.897314] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [280.897569] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452 <7> [280.897813] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913 <7> [280.898062] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893 <7> [280.898257] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793 <7> [280.898191] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.898448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.898546] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.898648] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.898830] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.898836] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.899040] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.899217] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.899394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.899580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.899747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.899948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [280.900513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.900720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [280.900935] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452 <7> [280.901156] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913 <7> [280.901363] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893 <7> [280.901554] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793 <7> [280.901725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.901927] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [280.902158] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [280.902324] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [280.902495] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.902657] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [280.902822] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [280.903000] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [280.903172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [280.903434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [280.903697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [280.903995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [280.904316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [280.904589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [280.905742] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.906049] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.914000] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.914200] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [280.947222] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.947530] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 452) -> ( 0 - 585), size 452 -> 585 <7> [280.947770] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 452 - 1365) -> ( 585 - 2894), size 913 -> 2309 <7> [280.948009] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2258) -> (2894 - 4051), size 893 -> 1157 <7> [280.948203] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0 <7> [280.948114] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.948393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.948490] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.948579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.948765] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [280.948783] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.949013] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [280.949223] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [280.949431] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.949607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.949781] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [280.950044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [280.950336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [280.950618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [280.950891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [280.951190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [280.951456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [280.952509] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [280.952792] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [280.953483] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [280.953749] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [280.963975] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.997013] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [280.997302] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [280.997528] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 585 - 2894) -> ( 376 - 3312), size 2309 -> 2936 <7> [280.997727] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (3312 - 4051), size 1157 -> 739 <7> [280.997910] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [280.998157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [280.998337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [280.998302] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [280.998536] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [280.998636] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [280.998737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [280.998918] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [280.999032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [280.999314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [280.999599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [280.999868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [281.000167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [281.001069] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.001359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.047177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.047541] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.047876] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 376) -> ( 0 - 679), size 376 -> 679 <7> [281.048187] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 376 - 3312) -> ( 679 - 1358), size 2936 -> 679 <7> [281.048317] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.048410] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3312 - 4051) -> (1358 - 2705), size 739 -> 1347 <7> [281.048622] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2705 - 4051), size 0 -> 1346 <7> [281.048724] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.048884] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.049170] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.049141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.049390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [281.049603] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [281.049813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.050042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.050233] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [281.050420] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [281.050684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [281.051006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [281.051299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [281.051594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [281.051930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [281.052242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [281.053570] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.053887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.063374] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [281.081152] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.081481] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.113680] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.113990] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.114128] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.114283] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 679) -> ( 0 - 456), size 679 -> 456 <7> [281.114522] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 679 - 1358) -> ( 456 - 1360), size 679 -> 904 <7> [281.114531] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.114739] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1358 - 2705) -> (1360 - 2259), size 1347 -> 899 <7> [281.114860] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.114974] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2705 - 4051) -> (2259 - 4051), size 1346 -> 1792 <7> [281.115170] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.115363] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.115573] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [281.115788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [281.116001] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.116175] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.116347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [281.116527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [281.116752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [281.117042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [281.117318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [281.117588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [281.117853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [281.118198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [281.119389] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.119673] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.130683] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.130889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.163674] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.164023] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 456) -> ( 0 - 583), size 456 -> 583 <7> [281.164082] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.164319] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 456 - 1360) -> ( 583 - 2898), size 904 -> 2315 <7> [281.164488] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.164541] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1360 - 2259) -> (2898 - 4051), size 899 -> 1153 <7> [281.164759] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2259 - 4051) -> ( 0 - 0), size 1792 -> 0 <7> [281.164818] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.165071] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.165315] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.165518] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.165751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.165967] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [281.166143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.166319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.166507] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.166727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [281.167065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [281.167342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [281.167614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [281.167877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [281.168172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [281.169191] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.169476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.170191] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [281.170436] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [281.180564] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.213653] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.214040] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [281.214134] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.214287] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939 <7> [281.214523] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737 <7> [281.214541] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.214747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.214872] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.214978] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [281.215184] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [281.215405] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [281.215636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [281.215922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [281.216242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [281.216519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [281.216788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [281.217131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [281.217845] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.218164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.263777] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.264316] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.264311] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.264616] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.264752] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.264990] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673 <7> [281.265210] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.265302] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692 <7> [281.265556] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333 <7> [281.265805] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353 <7> [281.266100] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.266359] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.266598] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.266834] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.267157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.267386] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [281.267634] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [281.267888] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [281.268282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [281.268658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [281.269028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [281.269422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [281.269753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [281.270127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [281.271403] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.271751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.279985] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [281.297713] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.298055] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.330561] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.330896] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.331278] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452 <7> [281.331370] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.331575] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913 <7> [281.331809] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893 <7> [281.331776] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.332071] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793 <7> [281.332165] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.332293] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.332556] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [281.332781] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [281.333057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [281.333266] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.333470] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.333676] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.333897] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.334238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [281.334564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [281.334879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [281.335361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [281.335701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [281.336074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [281.337285] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.337589] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.347418] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.347610] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.380243] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.380513] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 452) -> ( 0 - 583), size 452 -> 583 <7> [281.380703] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 452 - 1365) -> ( 583 - 2898), size 913 -> 2315 <7> [281.380888] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2258) -> (2898 - 4051), size 893 -> 1153 <7> [281.381154] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0 <7> [281.381346] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.381299] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.381532] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.381654] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.381734] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.381961] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.381979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.382128] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [281.382300] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.382466] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.382632] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.382837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [281.383350] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.383579] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 452) -> ( 0 - 583), size 452 -> 583 <7> [281.383764] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 452 - 1365) -> ( 583 - 2898), size 913 -> 2315 <7> [281.383961] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2258) -> (2898 - 4051), size 893 -> 1153 <7> [281.384138] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0 <7> [281.384310] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.384481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.384647] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.384832] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.385011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [281.385165] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.385319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.385474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.385636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [281.385884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [281.386177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [281.386421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [281.386660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [281.386911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [281.387965] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.388230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.388773] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [281.389026] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [281.397166] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.430234] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.430522] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [281.430724] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939 <7> [281.430923] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737 <7> [281.431198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.431395] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [281.431360] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.431588] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [281.431710] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.431813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [281.432014] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.432062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [281.432325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [281.432579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [281.432841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [281.433148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [281.433423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [281.434262] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.434531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.480363] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.480730] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.481137] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673 <7> [281.481233] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.481441] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692 <7> [281.481679] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333 <7> [281.481676] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.481908] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353 <7> [281.482090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.482257] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.482481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.482701] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.482940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.483173] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.483401] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [281.483654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [281.483880] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [281.484220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [281.484598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [281.484968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [281.485341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [281.485666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [281.486009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [281.487453] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.487796] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.496635] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [281.514238] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.514527] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.547036] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.547339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.547644] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452 <7> [281.547912] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913 <7> [281.548253] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893 <7> [281.548290] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.548492] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793 <7> [281.548723] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.548850] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.548976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [281.549219] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [281.549295] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.549448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [281.549676] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.549909] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.550207] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.550484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.550772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [281.551166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [281.551519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [281.551856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [281.552218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [281.552598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [281.553961] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.554324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.564017] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.564255] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.597163] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.597481] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 452) -> ( 0 - 585), size 452 -> 585 <7> [281.597717] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 452 - 1365) -> ( 585 - 2894), size 913 -> 2309 <7> [281.598009] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2258) -> (2894 - 4051), size 893 -> 1157 <7> [281.598140] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.598257] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0 <7> [281.598494] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.598582] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.598725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.598980] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [281.598986] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.599263] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [281.599499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [281.599713] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.599914] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.600185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.600435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [281.600817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [281.601170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [281.601496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [281.601801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [281.602150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [281.603279] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.603638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.604403] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [281.604703] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [281.613831] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.646959] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.647283] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [281.647519] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 585 - 2894) -> ( 376 - 3312), size 2309 -> 2936 <7> [281.647736] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (3312 - 4051), size 1157 -> 739 <7> [281.648004] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.648106] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.648232] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.648501] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [281.648527] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.648738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [281.648856] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.649039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [281.649368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [281.649688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [281.650016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [281.650393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [281.650720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [281.651610] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.651954] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.697070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.697441] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.697782] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 376) -> ( 0 - 679), size 376 -> 679 <7> [281.698096] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 376 - 3312) -> ( 679 - 1358), size 2936 -> 679 <7> [281.698233] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.698331] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3312 - 4051) -> (1358 - 2705), size 739 -> 1347 <7> [281.698559] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2705 - 4051), size 0 -> 1346 <7> [281.698674] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.698783] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.699042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.699093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.699320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [281.699540] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [281.699762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.700013] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.700220] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [281.700423] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [281.700666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [281.701019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [281.701354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [281.701738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [281.702108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [281.702450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [281.703996] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.704342] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.713267] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [281.730955] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.731243] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.763735] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.764103] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.764221] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.764428] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 679) -> ( 0 - 456), size 679 -> 456 <7> [281.764661] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.764733] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 679 - 1358) -> ( 456 - 1360), size 679 -> 904 <7> [281.765011] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1358 - 2705) -> (1360 - 2259), size 1347 -> 899 <7> [281.765051] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.765227] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2705 - 4051) -> (2259 - 4051), size 1346 -> 1792 <7> [281.765449] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.765656] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.765903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [281.766235] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [281.766467] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.766690] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.766898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [281.767157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [281.767416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [281.767761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [281.768155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [281.768555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [281.768880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [281.769228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [281.770466] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.770780] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.780662] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.780892] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.813722] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.814044] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 456) -> ( 0 - 814), size 456 -> 814 <7> [281.814132] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.814283] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 456 - 1360) -> ( 814 - 2440), size 904 -> 1626 <7> [281.814481] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1360 - 2259) -> (2440 - 4051), size 899 -> 1611 <7> [281.814467] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.814657] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2259 - 4051) -> ( 0 - 0), size 1792 -> 0 <7> [281.814741] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.814831] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.815061] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.815247] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [281.815436] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [281.815612] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.815785] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.815981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.816147] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.816314] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.816480] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [281.816650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 8, 8, 8, 8, 8, 0, 0, 19, 4, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [281.816818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [281.817027] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [281.817197] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.817369] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.817538] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [281.817745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [281.818072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [281.818359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [281.818647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [281.818894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [281.819191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [281.820146] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.820445] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.821133] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [281.821389] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [281.830539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.863580] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.864001] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [281.863971] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.864333] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [281.864423] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.864585] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [281.864826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.864784] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.865133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [281.865371] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [281.865648] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [281.865931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [281.866532] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.866820] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [281.867174] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [281.867399] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [281.867614] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.867834] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [281.868133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [281.868392] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [281.868654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [281.869023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [281.869368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [281.869679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [281.870041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [281.870411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [281.871312] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.871657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.913624] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.914009] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.914101] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.914349] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896 <7> [281.914540] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.914607] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471 <7> [281.914837] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774 <7> [281.914941] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.915125] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910 <7> [281.915358] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.915579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.915815] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.916082] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.916327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.916544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [281.916755] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [281.916995] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [281.917245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [281.917873] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.918187] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.918497] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896 <7> [281.918694] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471 <7> [281.918878] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774 <7> [281.919146] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910 <7> [281.919348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.919546] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.919748] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.919993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.920216] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.920414] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [281.920605] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [281.920819] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [281.921096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [281.921436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [281.921778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [281.922131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [281.922433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [281.922737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [281.924022] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.924381] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.929925] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [281.947467] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.947709] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.980257] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.980566] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [281.980873] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676 <7> [281.981251] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691 <7> [281.981368] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [281.981496] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335 <7> [281.981738] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349 <7> [281.981807] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [281.982012] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.982241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [281.982228] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [281.982493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [281.982746] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [281.983061] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [281.983297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [281.983530] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [281.983780] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [281.984105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [281.984504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [281.984853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [281.985226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [281.985557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [281.985870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [281.987175] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [281.987516] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [281.997134] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [281.997329] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.030293] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.030704] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 676) -> ( 0 - 814), size 676 -> 814 <7> [282.031073] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 676 - 1367) -> ( 814 - 2440), size 691 -> 1626 <7> [282.031137] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.031324] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2702) -> (2440 - 4051), size 1335 -> 1611 <7> [282.031560] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0 <7> [282.031575] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.031840] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.031969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.032116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [282.032348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [282.032587] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [282.032832] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [282.033115] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.033338] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.033573] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.033839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [282.034242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [282.034643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [282.034958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [282.035256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [282.035563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [282.036859] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.037238] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.037924] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [282.038209] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [282.047086] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.080195] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.080545] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [282.080793] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [282.081089] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [282.081149] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.081322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.081544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [282.081559] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.081762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [282.081933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.082033] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [282.082270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [282.082580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [282.082872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [282.083195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [282.083467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [282.083752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [282.084607] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.084913] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.130305] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.130629] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.130956] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896 <7> [282.131073] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.131159] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471 <7> [282.131350] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774 <7> [282.131432] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.131531] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910 <7> [282.131710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.131727] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.131901] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [282.132072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [282.132270] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [282.132452] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.132610] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [282.132772] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [282.133015] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [282.133219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [282.133490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [282.133754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [282.134128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [282.134424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [282.134766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [282.136273] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.136688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.146561] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [282.164242] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.164586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.196848] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.197189] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.197474] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676 <7> [282.197728] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691 <7> [282.197975] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335 <7> [282.198101] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.198180] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349 <7> [282.198422] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.198484] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.198625] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [282.198797] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.198818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [282.199062] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [282.199242] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.199424] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [282.199635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [282.199851] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [282.200158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [282.200487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [282.200790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [282.201139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [282.201429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [282.201710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [282.202978] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.203298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.213861] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.214103] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.247145] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.247454] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 676) -> ( 0 - 817), size 676 -> 817 <7> [282.247675] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 676 - 1367) -> ( 817 - 2434), size 691 -> 1617 <7> [282.247919] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2702) -> (2434 - 4051), size 1335 -> 1617 <7> [282.247942] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.248122] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0 <7> [282.248299] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.248355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.248549] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.248594] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.248737] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [282.248939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [282.249111] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [282.249278] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.249443] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.249610] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.249815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [282.250133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [282.250426] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [282.250702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [282.250978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [282.251237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [282.252347] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.252646] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.253296] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [282.253547] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [282.263742] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.296914] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.297245] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [282.297509] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 817 - 2434) -> ( 588 - 2893), size 1617 -> 2305 <7> [282.297725] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2434 - 4051) -> (2893 - 4051), size 1617 -> 1158 <7> [282.297968] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.298060] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.298173] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.298370] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [282.298412] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.298605] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [282.298702] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.298863] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [282.299317] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.299560] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [282.299753] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 817 - 2434) -> ( 588 - 2893), size 1617 -> 2305 <7> [282.299959] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2434 - 4051) -> (2893 - 4051), size 1617 -> 1158 <7> [282.300139] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.300315] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.300512] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [282.300717] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [282.300959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [282.301243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [282.301511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [282.301782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [282.302086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [282.302367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [282.303139] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.303425] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.346994] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.347586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.347938] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.348055] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.348276] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 588) -> ( 0 - 905), size 588 -> 905 <7> [282.348525] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 588 - 2893) -> ( 905 - 1360), size 2305 -> 455 <7> [282.348495] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.348760] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2893 - 4051) -> (1360 - 3152), size 1158 -> 1792 <7> [282.348860] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.349034] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3152 - 4051), size 0 -> 899 <7> [282.349264] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.349485] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.349716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [282.349967] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [282.350183] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.350410] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.350652] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [282.350861] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [282.351185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [282.351581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [282.351956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [282.352291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [282.352617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [282.352977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [282.354499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.354831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.363138] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [282.380713] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.381068] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.413441] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.413699] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.413977] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 905) -> ( 0 - 681), size 905 -> 681 <7> [282.414073] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.414211] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 905 - 1360) -> ( 681 - 1362), size 455 -> 681 <7> [282.414411] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1360 - 3152) -> (1362 - 2707), size 1792 -> 1345 <7> [282.414412] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.414587] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3152 - 4051) -> (2707 - 4051), size 899 -> 1344 <7> [282.414685] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.414760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.414985] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.415213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [282.415397] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [282.415599] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.415775] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.416008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [282.416254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [282.416506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [282.417062] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.417282] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.417490] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 905) -> ( 0 - 681), size 905 -> 681 <7> [282.417701] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 905 - 1360) -> ( 681 - 1362), size 455 -> 681 <7> [282.417906] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1360 - 3152) -> (1362 - 2707), size 1792 -> 1345 <7> [282.418102] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3152 - 4051) -> (2707 - 4051), size 899 -> 1344 <7> [282.418286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.418483] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.418682] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [282.418852] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [282.419080] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.419267] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.419456] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [282.419624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [282.419799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [282.420088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [282.420341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [282.420579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [282.420815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [282.421128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [282.422419] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.422708] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.430453] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.430655] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.463418] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.463708] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 681) -> ( 0 - 814), size 681 -> 814 <7> [282.463993] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 681 - 1362) -> ( 814 - 2440), size 681 -> 1626 <7> [282.464181] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1362 - 2707) -> (2440 - 4051), size 1345 -> 1611 <7> [282.464117] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.464365] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2707 - 4051) -> ( 0 - 0), size 1344 -> 0 <7> [282.464451] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.464545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.464720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [282.464728] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.464925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [282.465110] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [282.465296] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [282.465468] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.465641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.465806] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.466042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [282.466319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [282.466587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [282.466885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [282.467162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [282.467469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [282.468365] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.468652] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.469386] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [282.469656] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [282.480434] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.513425] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.513749] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [282.514094] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [282.514190] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.514320] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [282.514533] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.514595] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.514738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [282.514967] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [282.514932] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.515176] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [282.515433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [282.515723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [282.516053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [282.516364] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [282.516663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [282.516958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [282.517745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.518076] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.563546] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.564029] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.564147] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.564470] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896 <7> [282.564624] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.564768] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471 <7> [282.565077] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774 <7> [282.565100] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.565328] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910 <7> [282.565577] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.565822] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [282.566110] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [282.566347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [282.566572] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.566787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [282.567078] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [282.567338] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [282.567666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [282.568074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [282.568442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [282.568807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [282.569191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [282.569557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [282.570881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.571279] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.579793] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [282.597416] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.597739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.630153] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.630476] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.630783] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676 <7> [282.631093] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691 <7> [282.631219] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.631304] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335 <7> [282.631510] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349 <7> [282.631598] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.631707] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.631934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [282.631944] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.632130] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [282.632361] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [282.632575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.632757] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [282.632963] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [282.633136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [282.633337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [282.633619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [282.633911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [282.634189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [282.634460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [282.634708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [282.635762] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.636090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.647064] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.647278] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.680110] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.680430] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 676) -> ( 0 - 814), size 676 -> 814 <7> [282.680700] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 676 - 1367) -> ( 814 - 2440), size 691 -> 1626 <7> [282.680944] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2702) -> (2440 - 4051), size 1335 -> 1611 <7> [282.680996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.681141] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0 <7> [282.681330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.681351] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.681513] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [282.681641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.681708] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [282.681934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [282.682133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [282.682349] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.682544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.682775] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.683049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [282.683393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [282.683705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [282.684032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [282.684370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [282.684648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [282.685793] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.686284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.687790] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [282.688130] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [282.697057] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.730070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.730354] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [282.730552] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [282.730739] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [282.730982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.731013] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.731177] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [282.731385] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [282.731368] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.731608] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [282.731659] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.731896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [282.732287] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.732515] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [282.732680] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [282.732874] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [282.733057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.733238] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [282.733420] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [282.733650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [282.733875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [282.734160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [282.734436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [282.734703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [282.734993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [282.735316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [282.736172] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.736462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.780441] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.781035] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.781022] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.781367] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.781500] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.781721] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896 <7> [282.781933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.782084] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471 <7> [282.782316] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774 <7> [282.782590] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910 <7> [282.782820] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.783125] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [282.783362] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [282.783618] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [282.783878] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.784111] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [282.784347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [282.784574] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [282.784918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [282.785281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [282.785622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [282.786050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [282.786437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [282.786810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [282.788443] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.788825] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.796435] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [282.814220] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.814553] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.846973] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.846992] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.847280] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.847434] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.847591] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676 <7> [282.847790] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.847937] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691 <7> [282.848177] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335 <7> [282.848423] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349 <7> [282.848654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.848914] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [282.849170] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [282.849429] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [282.849682] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.849939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [282.850165] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [282.850387] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [282.850657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [282.851052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [282.851404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [282.851738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [282.852157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [282.852484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [282.853796] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.854168] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.863637] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.863860] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.896985] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.896980] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.897321] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 676) -> ( 0 - 817), size 676 -> 817 <7> [282.897394] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.897614] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 676 - 1367) -> ( 817 - 2434), size 691 -> 1617 <7> [282.897727] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.897864] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2702) -> (2434 - 4051), size 1335 -> 1617 <7> [282.898088] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0 <7> [282.898308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.898521] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.898757] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [282.899020] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [282.899230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [282.899435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.899635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.899851] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.900127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [282.900716] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.901025] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 676) -> ( 0 - 817), size 676 -> 817 <7> [282.901253] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 676 - 1367) -> ( 817 - 2434), size 691 -> 1617 <7> [282.901462] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2702) -> (2434 - 4051), size 1335 -> 1617 <7> [282.901660] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0 <7> [282.901881] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.902069] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.902265] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [282.902455] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [282.902640] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [282.902816] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.903048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.903242] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [282.903413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [282.903682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [282.903979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [282.904237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [282.904485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [282.904739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [282.905823] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.906134] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.906728] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [282.907029] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [282.913635] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.946726] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.947096] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [282.947091] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.947332] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 817 - 2434) -> ( 588 - 2893), size 1617 -> 2305 <7> [282.947549] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2434 - 4051) -> (2893 - 4051), size 1617 -> 1158 <7> [282.947528] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.947757] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.947865] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.948008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.948258] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [282.948459] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [282.948684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [282.949009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [282.949287] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [282.949558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [282.949885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [282.950179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [282.951033] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [282.951338] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [282.996880] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [282.997232] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [282.997547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 588) -> ( 0 - 905), size 588 -> 905 <7> [282.997781] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 588 - 2893) -> ( 905 - 1360), size 2305 -> 455 <7> [282.998109] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2893 - 4051) -> (1360 - 3152), size 1158 -> 1792 <7> [282.998225] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [282.998343] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3152 - 4051), size 0 -> 899 <7> [282.998573] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.998663] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [282.998797] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.999084] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [282.999042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [282.999292] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [282.999488] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [282.999678] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [282.999898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [283.000099] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [283.000322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [283.000638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [283.000972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [283.001308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [283.001628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [283.001961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [283.003526] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.003890] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.013036] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [283.030685] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [283.031056] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [283.063348] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [283.063638] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [283.063969] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 905) -> ( 0 - 681), size 905 -> 681 <7> [283.064057] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.064259] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 905 - 1360) -> ( 681 - 1362), size 455 -> 681 <7> [283.064477] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1360 - 3152) -> (1362 - 2707), size 1792 -> 1345 <7> [283.064460] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.064691] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3152 - 4051) -> (2707 - 4051), size 899 -> 1344 <7> [283.064797] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.064932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.065129] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [283.065344] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [283.065545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [283.065733] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.065972] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [283.066189] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [283.066404] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [283.066655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [283.067011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [283.067312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [283.067594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [283.067894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [283.068194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [283.069431] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.069739] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.080309] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [283.080505] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [283.113448] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 681) -> ( 0 - 2026), size 681 -> 2026 <7> [283.113731] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 681 - 1362) -> (2026 - 4051), size 681 -> 2025 <7> [283.114017] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1362 - 2707) -> ( 0 - 0), size 1345 -> 0 <7> [283.114150] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.114233] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2707 - 4051) -> ( 0 - 0), size 1344 -> 0 <7> [283.114439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.114530] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.114638] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.114866] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.114871] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.115051] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.115241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.115422] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.115601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.115813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.116047] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [283.116239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.116400] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.116571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.116747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [283.116962] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.117150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.117342] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.117540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [283.117815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [283.118124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [283.118446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.118716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.119032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [283.119797] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.120129] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.120880] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [283.121145] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:35:plane 1A] <7> [283.163357] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [283.163646] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [283.163939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.164054] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.164180] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.164426] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.164459] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.164664] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.164791] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.164949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [283.165258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [283.165576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [283.165879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [283.166225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [283.166524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [283.167420] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.167737] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.196677] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.197004] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [283.197084] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.197209] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [283.197386] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [283.197425] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.197555] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.197724] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.197695] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.197982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.198177] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.198368] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.198534] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [283.198700] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [283.198932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [283.199112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [283.199371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [283.199622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [283.199887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [283.200165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [283.200441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [283.201684] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.202021] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.213535] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.246765] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.247180] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [283.247163] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.247432] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [283.247570] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.247664] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [283.247944] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.247950] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.248185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.248462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.248738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.249049] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.249274] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.249497] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.249714] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.250060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [283.250552] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.250870] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [283.251129] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [283.251349] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [283.251578] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.251792] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.252060] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.252255] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.252460] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.252655] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.252896] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.253103] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.253312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [283.253650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [283.254066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [283.254388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [283.254698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [283.255066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [283.256069] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.256409] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.263581] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.296666] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [283.296954] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [283.297073] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.297156] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [283.297346] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.297407] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.297529] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.297676] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.297725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.297982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.298185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [283.298406] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.298588] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.298827] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.299049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [283.299536] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [283.299747] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [283.299966] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [283.300147] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.300323] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.300506] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.300716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.300944] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [283.301119] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.301292] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.301450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.301618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [283.301947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [283.302230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [283.302508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.302775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.303109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [283.303945] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.304246] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.330045] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [283.330330] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [283.330557] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.330767] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.331046] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.331169] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.331273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.331537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [283.331547] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.331866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [283.331897] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.332185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [283.332542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [283.332865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [283.333205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [283.334110] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.334402] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.363292] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.363617] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [283.363918] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [283.364043] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.364131] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [283.364322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.364422] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.364505] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.364686] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.364735] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.364930] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.365101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.365290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [283.365467] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [283.365631] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [283.365847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [283.366169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [283.366443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [283.366715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [283.367061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [283.367340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [283.368360] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.368659] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.380146] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.413715] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.413973] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.414251] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [283.414327] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.414533] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [283.414603] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.414768] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [283.415019] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.415241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.415459] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.415673] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.415898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.416108] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.416319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.416529] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.416800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [283.417203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [283.417577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [283.417959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [283.418322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [283.418683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [283.420488] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.420839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.430106] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.463931] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [283.463869] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.464302] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [283.464450] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.464597] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [283.464906] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.464933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.465153] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [283.465392] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [283.465630] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [283.465883] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [283.466116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.466350] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.466586] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.466889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [283.467308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [283.467717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [283.468142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.468539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.468950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [283.470417] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.470820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.496843] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [283.496842] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.497121] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [283.497223] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.497348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.497564] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [283.497549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.497776] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [283.498008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [283.498266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [283.498643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [283.499028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [283.499386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [283.499741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [283.500121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [283.501375] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.501697] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.530098] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.530440] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [283.530670] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [283.530926] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [283.530934] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.531146] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.531281] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.531356] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [283.531568] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [283.531600] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.531779] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [283.532021] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.532234] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [283.532442] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [283.532650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [283.532925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [283.533298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [283.533659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [283.534016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [283.534344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [283.534670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [283.536168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.536495] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.546874] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.580177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.580553] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [283.580870] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [283.580869] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.581119] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [283.581244] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.581354] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.581589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [283.581593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.581848] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [283.582086] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [283.582319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.582547] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [283.582777] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [283.583029] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [283.583314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [283.583731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [283.584126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [283.584492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [283.584887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [283.585248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [283.586834] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.587189] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.596877] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.630144] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026 <7> [283.630482] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025 <7> [283.630744] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [283.631032] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.631035] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.631285] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.631406] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.631521] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.631755] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.631751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.632015] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [283.632250] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.632483] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.632716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.633014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [283.633394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [283.633757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [283.634138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.634497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.634871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [283.636056] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.636411] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.680114] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [283.680414] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [283.680647] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.680918] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.680909] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.681143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.681253] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.681357] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.681567] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.681612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [283.682207] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [283.682436] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [283.682647] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.682877] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.683089] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.683297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.683523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [283.683908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [283.684271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [283.684631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [283.685025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [283.685381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [283.686418] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.686741] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.713458] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.713851] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [283.713843] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.714088] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [283.714186] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.714305] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [283.714517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.714499] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.714739] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.714981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.715192] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.715399] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.715605] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [283.715837] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [283.716049] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [283.716300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [283.716878] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.717158] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [283.717382] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [283.717593] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [283.717844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.718061] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.718273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.718484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.718695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.718928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [283.719125] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [283.719323] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [283.719531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [283.719868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [283.720182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [283.720479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [283.720761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [283.721055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [283.722037] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.722276] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.730105] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.763321] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.763689] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [283.763988] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [283.763997] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.764223] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [283.764442] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.764381] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.764655] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.764723] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.764917] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.765134] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.765345] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.765555] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.765765] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.765993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.766253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [283.766977] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.767262] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [283.767480] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [283.767690] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [283.767925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.768135] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.768348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.768559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.768767] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.768998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.769212] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.769423] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.769654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [283.770039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [283.770407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [283.770766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [283.771120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [283.771452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [283.772707] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.773055] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.780210] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.813286] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [283.813590] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [283.813921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [283.814059] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.814198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.814468] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.814539] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.814756] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.814996] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.815115] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.815395] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [283.815666] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.815945] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.816193] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.816497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [283.816915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [283.817261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [283.817600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.817969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.818351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [283.819396] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.819819] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.846658] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [283.847005] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [283.847141] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.847254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.847486] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.847548] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.847730] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.847936] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.848023] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.848264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [283.848587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [283.848929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [283.849219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [283.849514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [283.849824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [283.850684] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.851030] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.879930] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.880246] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [283.880489] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [283.880683] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [283.880948] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.881071] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.881166] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.881395] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.881481] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.881597] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.881812] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.881839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.881992] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [283.882168] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [283.882375] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [283.882581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [283.882891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [283.883183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [283.883471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [283.883824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [283.884154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [283.885209] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.885522] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.896803] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.929928] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.930287] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [283.930553] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [283.930850] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [283.930989] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.931087] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.931310] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [283.931392] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.931531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [283.931731] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.931799] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [283.932011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.932222] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [283.932427] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [283.932629] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [283.932916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [283.933252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [283.933578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [283.934629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [283.934997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [283.935326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [283.936540] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.936913] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [283.946873] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [283.980170] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [283.980462] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [283.980701] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [283.980997] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [283.981128] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [283.981213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [283.981419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [283.981507] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [283.981661] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [283.981849] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [283.981908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [283.982100] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.982294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.982480] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [283.982696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2 <7> [283.983049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [283.983383] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [283.983705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.984056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [283.984394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [283.985359] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [283.985699] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.013200] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [284.013469] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [284.013681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.013931] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.013967] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.014117] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [284.014332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [284.014350] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.014537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [284.014650] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.014826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [284.015103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [284.015373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.015646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.015937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [284.016746] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.017072] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.046603] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.046996] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [284.047089] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.047242] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [284.047472] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [284.047532] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.047689] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.048003] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.047974] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.048226] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [284.048437] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [284.048644] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.048940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.049145] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [284.049332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [284.049547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [284.049876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [284.050231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [284.050548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [284.050895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [284.051211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [284.052387] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.052737] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.063469] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.096615] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.096995] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [284.097091] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.097230] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [284.097443] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [284.097468] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.097650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.097823] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.097889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.098108] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [284.098338] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [284.098545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.098738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.098996] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [284.099192] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [284.099409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [284.099839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.100090] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [284.100342] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [284.100536] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [284.100741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.100979] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.101165] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [284.101334] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [284.101518] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.101690] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.101925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [284.102118] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [284.102322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [284.102607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [284.102903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [284.103211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.103495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.103814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [284.104872] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.105174] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.113400] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.146620] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691 <7> [284.146950] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360 <7> [284.147062] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.147178] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [284.147390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.147439] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.147595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.147748] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.147840] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.148045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.148277] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.148472] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.148654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.148867] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.149038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [284.149239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.149430] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.149589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.149822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [284.150251] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691 <7> [284.150457] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360 <7> [284.150644] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [284.150866] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.151061] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.151258] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.151454] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.151623] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.151828] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.152038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.152237] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.152435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [284.152627] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.152847] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.153046] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.153256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [284.153587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [284.153946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [284.154336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.154680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.155254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [284.156222] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.156548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.196599] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [284.197023] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [284.197152] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.197273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.197504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.197560] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.197725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.197968] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.198048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.198313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [284.198856] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [284.199116] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [284.199352] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.199579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.199895] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.200116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.200337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [284.200841] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [284.201088] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [284.201307] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.201564] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.201823] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.202027] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.202241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [284.202583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [284.202970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [284.203307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.203634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.203995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [284.204868] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.205189] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.230269] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:494] <7> [284.230934] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.231457] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.231942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.254153] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.254436] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [284.254607] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [284.254790] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [284.254942] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.255089] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.255231] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.255384] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.255535] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.255660] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [284.255801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [284.255917] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [284.256050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [284.256363] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.256495] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [284.256602] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [284.256705] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [284.256908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.257010] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.257107] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.257208] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.257310] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.257406] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [284.257489] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [284.257579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [284.257681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [284.257884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [284.258018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [284.258142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [284.258261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [284.258377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [284.258858] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.258983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.263330] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.296603] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.297176] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [284.297146] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.297623] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [284.297816] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.298053] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [284.298312] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.298433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.298773] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.299117] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.299429] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.299736] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.300136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.300433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.300730] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.301172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [284.301660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [284.302168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [284.302636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [284.303123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [284.303611] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [284.304845] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.305242] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.313306] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.346554] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [284.346921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [284.347052] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.347192] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [284.347441] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.347487] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.347678] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.347969] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.347909] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.348221] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.348498] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [284.348721] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.349024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.349244] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.349532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [284.350448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [284.350831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [284.351183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.351522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.351874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [284.352899] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.353243] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.379907] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [284.380236] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [284.380502] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.380793] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.380930] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.381061] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.381336] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.381405] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.381619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [284.381832] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.382045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [284.382412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [284.382779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.383163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.383542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [284.384630] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.385007] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.413142] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.413457] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [284.413728] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [284.414015] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [284.414228] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.414154] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.414440] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.414561] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.414633] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.414862] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.414933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.415070] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.415279] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [284.415467] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [284.415654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [284.415928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [284.416266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [284.416596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [284.416965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [284.417330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [284.417681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [284.418807] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.419148] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.430097] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.463141] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.463491] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [284.463737] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [284.464084] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [284.464203] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.464339] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.464580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.464637] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.464851] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.465040] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.465120] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.465332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.465545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.465769] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.465993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.466230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [284.466558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [284.466925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [284.467298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [284.467607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [284.468000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [284.469207] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.469549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.480151] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.513342] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [284.513630] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [284.513932] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [284.514074] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.514154] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.514364] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.514454] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.514571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [284.514814] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [284.514793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.515020] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [284.515220] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.515446] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.515640] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.515909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [284.516224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [284.516535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [284.516859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.517154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.517452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [284.518334] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.518655] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.546523] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [284.546879] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [284.546911] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.547145] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.547386] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.547343] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.547621] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [284.547698] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.547933] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [284.548198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [284.548556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [284.548935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [284.549283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.549613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.550014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [284.551033] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.551381] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.579925] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.580317] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [284.580585] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [284.580884] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [284.581020] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.581133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.581374] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.581454] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.581614] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [284.581856] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.581934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [284.582145] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.582397] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.582602] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [284.582843] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [284.583080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [284.583564] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.583879] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [284.584090] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [284.584287] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [284.584524] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.584726] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.584998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [284.585256] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [284.585478] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.585694] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.585952] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [284.586164] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [284.586379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [284.586696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [284.587108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [284.587460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [284.587776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [284.588104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [284.589214] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.589497] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.596581] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.629914] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.630258] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [284.630503] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [284.630774] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [284.630905] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.630988] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.631195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.631285] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.631399] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [284.631598] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.631639] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [284.631896] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.632094] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.632290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [284.632486] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [284.632716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [284.633241] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.633518] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [284.633762] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [284.633970] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [284.634173] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.634404] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.634608] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [284.634850] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [284.635030] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.635199] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [284.635380] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [284.635564] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [284.635775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [284.636075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [284.636381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [284.636655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [284.636945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [284.637211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [284.638195] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.638476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.646571] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.679850] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691 <7> [284.680167] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360 <7> [284.680430] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0 <7> [284.680687] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.681020] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.681120] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.681298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.681568] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.681557] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.681838] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [284.681962] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.682049] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.682260] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.682517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.682811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [284.683374] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691 <7> [284.683608] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360 <7> [284.683876] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0 <7> [284.684097] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.684348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.684561] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.684833] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.685053] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [284.685264] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.685467] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.685658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.685910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [284.686220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [284.686526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [284.686855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.687162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.687486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [284.688255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.688557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.713091] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [284.713360] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [284.713575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.713841] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.713978] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.714054] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.714300] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.714356] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.714557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [284.714669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.714925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [284.715255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [284.715568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.715915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.716263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [284.717084] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.717377] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.746426] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.746811] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [284.746917] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.747066] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [284.747264] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [284.747328] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.747458] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.747654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.747667] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.747904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.748157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.748375] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.748601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [284.748846] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [284.749037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [284.749262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [284.749581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [284.749922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [284.750280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [284.750600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [284.750932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [284.751822] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.752145] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.763517] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.796480] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.796929] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [284.796982] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.797280] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [284.797459] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.797553] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [284.797875] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.797908] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.798133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.798389] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.798697] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.799038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.799282] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.799524] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.799826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.800106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [284.800485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [284.800912] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [284.801351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [284.801750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [284.802083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [284.803192] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.803580] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.813275] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.846425] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [284.846702] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [284.847032] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [284.847151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.847275] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.847498] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.847556] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.847710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.847917] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.848027] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.848241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [284.848441] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.848637] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.848914] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [284.849156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [284.849478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [284.849807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [284.850113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.850409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [284.850696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [284.851668] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.852018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.879815] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [284.880076] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [284.880287] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.880490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.880799] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.880910] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.881058] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.881343] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.881349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [284.881702] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.881734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [284.882037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [284.882393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.882742] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [284.883045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [284.883923] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.884259] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.913053] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.913348] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [284.913550] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [284.913782] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [284.913978] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.913921] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.914172] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.914301] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.914355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.914572] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.914615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.914821] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.914994] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [284.915176] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [284.915351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [284.915545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [284.915823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [284.916074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [284.916327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [284.916630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [284.916920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [284.917930] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.918223] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.930051] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.963016] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [284.963310] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [284.963561] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [284.963819] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [284.963998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.963959] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [284.964178] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [284.964350] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [284.964314] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [284.964530] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [284.964605] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [284.964697] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [284.964919] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [284.965089] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [284.965277] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [284.965485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [284.965779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [284.966059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [284.966322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [284.966589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [284.966935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [284.967952] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [284.968245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [284.979921] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [285.013230] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [285.013472] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [285.013667] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [285.013950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.014149] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.014069] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.014340] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [285.014447] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.014567] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [285.014823] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [285.014783] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.015026] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.015211] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.015398] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.015611] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [285.016107] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [285.016303] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [285.016482] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [285.016655] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.016905] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.017077] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [285.017231] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [285.017389] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [285.017533] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.017674] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.017882] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.018051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2 <7> [285.018325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [285.018601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [285.018946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [285.019231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [285.019545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [285.020428] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.020740] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.046427] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [285.046683] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [285.046975] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.047109] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.047180] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.047379] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [285.047462] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.047603] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [285.047787] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.047868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [285.048292] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [285.048498] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [285.048695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.049010] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.049210] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [285.049415] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [285.049602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2 <7> [285.049903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [285.050164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [285.050417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [285.050671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [285.050958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [285.051689] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.051975] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.079854] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [285.080239] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [285.080565] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [285.080887] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [285.081001] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.081169] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.081425] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.081476] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.081677] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [285.081914] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.082036] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [285.082279] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.082499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.082732] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [285.082948] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [285.083198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [285.083720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [285.083994] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [285.084204] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [285.084410] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [285.084610] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.084897] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.085103] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [285.085315] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [285.085523] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.085752] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.085961] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [285.086161] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [285.086373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [285.086716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [285.087053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [285.087359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [285.087635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [285.088101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [285.089269] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.089543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.096416] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [285.129696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [285.130041] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [285.130264] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [285.130454] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [285.130638] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.130885] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.130933] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.131086] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [285.131325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [285.131291] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.131539] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.131582] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.131779] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.132002] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [285.132204] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [285.132438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [285.132944] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [285.133170] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [285.133357] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [285.133547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [285.133760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.133959] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.134137] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [285.134353] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [285.134559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.134742] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.134919] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [285.135094] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [285.135282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [285.135550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [285.135843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [285.136108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [285.136365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [285.136645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [285.137648] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.137966] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.146537] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A] <7> [285.179748] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.180092] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597 <7> [285.180338] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293 <7> [285.180566] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161 <7> [285.180853] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.180986] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.181063] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [285.181290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [285.181365] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.181521] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [285.181673] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.181750] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.181934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [285.182123] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [285.182299] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [285.182471] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.182639] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.182852] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [285.183042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [285.183267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [285.183537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [285.184388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [285.184674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [285.184974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [285.185247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [285.186074] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.186367] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.196046] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:35:plane 1A] <7> [285.196386] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [285.196534] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [285.213644] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.246339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.246659] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [285.246996] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [285.247099] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.247211] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [285.247412] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.247476] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.247609] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [285.247851] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [285.247837] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.248057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [285.248294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [285.248601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [285.248949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [285.249276] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [285.249596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [285.249925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [285.250729] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.251067] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.296407] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.296765] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.296870] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.297084] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [285.297278] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.297361] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [285.297582] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [285.297606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.297848] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [285.298077] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.298315] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [285.298564] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [285.298823] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [285.299044] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.299264] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [285.299488] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [285.299719] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [285.299947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [285.300260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [285.300572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [285.300921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [285.301293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [285.301607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [285.302726] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.303062] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.312712] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [285.330221] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.330515] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.362966] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.363216] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.363459] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [285.363744] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [285.363926] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [285.363865] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.364100] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [285.364197] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.364269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.364469] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [285.364469] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.364652] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [285.364878] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [285.365072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.365249] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [285.365425] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [285.365633] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [285.365903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [285.366195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [285.366476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [285.366775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [285.367096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [285.367364] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [285.368220] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.368520] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.379877] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.380081] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.412978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.413272] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [285.413496] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [285.413732] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [285.413926] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [285.413859] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.414114] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.414214] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.414297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [285.414479] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [285.414504] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.414658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [285.414954] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [285.415166] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.415341] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.415545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.415818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [285.416110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [285.416392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [285.416660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [285.416967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [285.417247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [285.418347] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.418648] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.419319] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [285.419578] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [285.429881] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.462996] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.463340] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [285.463621] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [285.463920] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [285.464050] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.464133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.464336] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [285.464426] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.464538] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [285.464767] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [285.464773] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.465011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [285.465311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [285.465612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [285.465927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [285.466201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [285.466528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [285.467381] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.467659] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.513373] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.513843] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.513951] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.514278] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.514322] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.514634] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [285.514770] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.515016] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [285.515268] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [285.515510] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [285.515790] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.516062] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [285.516296] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [285.516525] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [285.516790] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.517013] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [285.517287] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [285.517531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [285.517839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [285.518219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [285.518598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [285.518986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [285.519320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [285.519639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [285.521078] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.521424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.529326] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [285.547079] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.547390] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.579855] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.580134] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.580412] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [285.580735] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [285.580748] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.580951] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [285.581158] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [285.581164] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.581361] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.581483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.581565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [285.581801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [285.581996] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [285.582186] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.582372] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [285.582559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [285.582790] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [285.583025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [285.583381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [285.583693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [285.583955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [285.584222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [285.584482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [285.585533] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.585853] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.596662] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.596889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.629780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.630077] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [285.630299] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [285.630490] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [285.630719] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [285.630901] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.630836] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.631075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.631169] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.631248] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [285.631452] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [285.631444] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.631647] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [285.631893] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.632072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.632244] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.632447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [285.632944] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.633182] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [285.633403] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [285.633583] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [285.633792] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [285.633975] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.634143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.634307] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [285.634470] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [285.634633] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [285.634861] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.635037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.635203] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.635373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [285.635635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [285.635944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [285.636209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [285.636478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [285.636761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [285.637693] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.637973] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.638574] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [285.638842] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [285.646485] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.679596] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.679963] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [285.680246] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [285.680462] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [285.680699] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.680845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.680954] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.681180] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [285.681225] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.681407] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [285.681537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.681691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [285.681988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [285.682284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [285.682553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [285.682907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [285.683184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [285.684044] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.684341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.729795] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.730174] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.730515] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [285.730883] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [285.731019] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.731117] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [285.731393] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [285.731462] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.731621] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.731895] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.731884] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.732163] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [285.732379] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [285.732638] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.732912] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.733116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [285.733318] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [285.733557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [285.733932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [285.734269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [285.734605] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [285.734970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [285.735315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [285.736686] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.737023] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.745937] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [285.763536] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.763867] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.796302] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.796608] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.796995] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [285.797091] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.797301] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [285.797537] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [285.797528] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.797843] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [285.797950] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.798074] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.798298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.798522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [285.798847] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [285.799101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.799334] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [285.799566] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [285.799842] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [285.800136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [285.800487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [285.800853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [285.801163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [285.801467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [285.801818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [285.802988] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.803315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.813217] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.813416] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.846176] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.846445] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597 <7> [285.846727] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293 <7> [285.846925] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161 <7> [285.846863] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.847114] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [285.847217] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.847298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.847477] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [285.847504] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.847676] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [285.847894] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [285.848098] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [285.848286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.848448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.848606] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [285.848839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [285.849132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [285.849420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [285.849716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [285.850044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [285.850312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [285.851140] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.851435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.852206] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [285.852472] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [285.863327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.896168] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.896464] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [285.896774] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [285.896966] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [285.896907] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.897157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.897241] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.897339] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [285.897518] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [285.897518] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.897768] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [285.898027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [285.898304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [285.898581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [285.898888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [285.899165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [285.899439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [285.900235] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.900526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.946170] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.946440] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [285.946721] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [285.946826] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [285.946913] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [285.947088] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [285.947161] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [285.947251] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [285.947411] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.947433] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [285.947570] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [285.947764] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [285.947951] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [285.948162] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [285.948330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [285.948490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [285.948714] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [285.948939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [285.949231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [285.949504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [285.949812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [285.950131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [285.950390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [285.951201] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [285.951496] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [285.962612] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [285.980116] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [285.980405] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.012981] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.013227] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.013471] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [286.013765] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [286.013957] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [286.013889] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.014144] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [286.014240] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.014327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.014507] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [286.014531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.014716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [286.014899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [286.015105] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.015268] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [286.015428] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [286.015589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [286.015843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [286.016131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [286.016411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [286.017240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [286.017523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [286.017809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [286.018615] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.018952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.029897] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.030111] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.063053] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.063336] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [286.063541] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [286.063787] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [286.063968] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [286.063915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.064147] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.064250] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.064322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [286.064496] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [286.064524] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.064738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [286.064928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [286.065107] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [286.065286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [286.065461] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [286.065692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [286.066011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [286.066280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [286.066542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [286.066832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [286.067116] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [286.068204] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.068485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.069120] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2 <7> [286.069383] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [286.079752] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.112878] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.113175] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [286.113386] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [286.113584] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [286.113844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.114036] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [286.113970] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.114244] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [286.114322] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.114459] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [286.114615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.114684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [286.115130] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.115364] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [286.115567] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [286.115795] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [286.115961] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.116150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [286.116308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [286.116478] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [286.116676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [286.116945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [286.117208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [286.117465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [286.117726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [286.118020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [286.118833] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.119141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.163005] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.163366] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.163741] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [286.163819] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.163976] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [286.164196] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [286.164226] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.164406] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [286.164561] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.164612] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.164872] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [286.165072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [286.165297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [286.165480] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.165683] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [286.165880] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [286.166074] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [286.166305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [286.166928] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.167171] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.167412] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [286.167607] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [286.167864] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [286.168098] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [286.168308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.168522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [286.168748] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [286.168976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [286.169158] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.169331] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [286.169506] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [286.169706] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [286.169888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [286.170189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [286.170482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [286.170793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [286.171107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [286.171392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [286.172488] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.172802] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.179221] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [286.196692] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.196961] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.229498] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.229807] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.229939] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.230061] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [286.230303] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [286.230292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.230493] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [286.230574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.230714] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [286.230887] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.231057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [286.231257] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [286.231443] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [286.231607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.231835] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [286.232035] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [286.232210] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [286.232414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [286.232709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [286.233002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [286.233300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [286.233583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [286.233935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [286.234911] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.235190] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.246443] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.246646] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.279801] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.279985] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.280198] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.280317] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [286.280542] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [286.280510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.280788] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [286.280975] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [286.281156] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.281333] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [286.281510] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [286.281766] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [286.281968] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [286.282145] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [286.282327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [286.282505] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [286.282755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3 <7> [286.283055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [286.283345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [286.283647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [286.283956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [286.284225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [286.285285] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.285574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.286272] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2 <7> [286.286526] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [286.296427] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.329543] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.329953] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [286.329966] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.330263] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [286.330370] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.330493] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [286.330749] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.330742] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.330966] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [286.331185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [286.331446] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [286.331739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3 <7> [286.332065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [286.332387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [286.332733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [286.333037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [286.333322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [286.334762] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.335080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.379521] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.379879] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.379983] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.380237] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [286.380364] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.380471] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [286.380720] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [286.380713] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.380925] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [286.381123] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.381318] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [286.381531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [286.381801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [286.382038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.382233] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [286.382436] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [286.382681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [286.382903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4 <7> [286.383225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [286.383496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [286.383817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [286.384110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [286.384400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [286.385590] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.385948] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.395833] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [286.413214] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.413481] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.446155] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.446437] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.446757] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [286.446831] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.447010] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [286.447207] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [286.447214] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.447395] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [286.447496] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.447584] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.447814] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [286.447987] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [286.448190] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [286.448352] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.448510] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [286.448709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [286.448889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [286.449118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [286.449404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [286.449703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [286.449984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [286.450270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [286.450596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [286.451733] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.452042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.463145] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.463337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.496275] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.496577] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823 <7> [286.496877] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614 <7> [286.497090] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614 <7> [286.497027] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.497292] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [286.497405] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.497490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.497723] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [286.497751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.497919] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [286.498164] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [286.498382] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.498571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [286.498810] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [286.499000] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [286.499195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.499386] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [286.499571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [286.499811] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [286.499991] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [286.500176] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [286.500374] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [286.500543] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [286.500802] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3 <7> [286.501147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [286.501441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [286.501756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [286.502065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [286.502341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [286.503166] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.503447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.504088] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2 <7> [286.504323] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A] <7> [286.513150] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.546177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.546496] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [286.546791] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [286.546999] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [286.546935] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.547198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.547290] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.547387] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [286.547575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [286.547572] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.547821] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [286.548024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [286.548407] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.548652] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [286.548827] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [286.549008] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [286.549184] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.549394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [286.549598] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [286.550032] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [286.550238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3 <7> [286.550533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [286.550960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [286.551278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [286.551590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [286.552001] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [286.552899] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.553232] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.596233] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.596798] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.596876] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.597185] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.597236] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.597506] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [286.597601] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.597805] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [286.598036] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [286.598263] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [286.598476] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.598719] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [286.598966] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [286.599178] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [286.599371] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.599562] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [286.599796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [286.600000] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [286.600224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4 <7> [286.600520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [286.600846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [286.601187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [286.601481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [286.601793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [286.602703] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [286.603042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [286.612485] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A] <7> [286.630044] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.630352] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.662789] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.663051] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.663314] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [286.663540] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [286.663815] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [286.663940] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [286.664014] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [286.664256] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.664321] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [286.664460] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [286.664703] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [286.664661] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [286.664893] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [286.665079] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.665269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [286.665474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [286.665742] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [286.665980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4 <7> [286.666542] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A] <7> [286.666816] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A] <7> [286.667048] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [286.667240] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [286.667423] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [286.667633] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [286.667808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [286.667976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [286.668150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [286.668327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [286.668506] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,*stwm <7> [286.668704] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [286.668906] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [286.669083] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<6> [268.344599] Console: switching to colour dummy device 80x25

<6> [268.344905] [IGT] kms_rotation_crc: executing

<7> [268.350320] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]

<7> [268.350329] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]

<7> [268.350479] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4

<7> [268.350571] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected

<7> [268.350818] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]

<7> [268.350821] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]

<7> [268.350939] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4

<7> [268.351024] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected

<7> [268.351230] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]

<7> [268.351233] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]

<7> [268.351345] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4

<7> [268.351426] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected

<7> [268.351690] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1]

<7> [268.351693] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:393:eDP-1]

<7> [268.352157] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00

<7> [268.352472] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000

<7> [268.352681] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [268.352774] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [268.352878] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz

<5> [268.352883] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [268.352885] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [268.352885] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] DisplayID extension version 0x13, primary use 0x00

<7> [268.352888] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<5> [268.352890] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [268.352891] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD monitor

<5> [268.352894] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [268.352895] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:393:eDP-1] ELD size 20, SAD count 0

<5> [268.352897] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [268.352909] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] VRR capable: yes

<7> [268.352992] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [268.353075] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:393:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<5> [268.353385] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [268.353387] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [268.353389] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [268.353444] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:393:eDP-1] probed modes:

<7> [268.353447] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [268.353451] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [268.353464] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1]

<7> [268.353467] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:402:DP-1]

<7> [268.353626] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:402:DP-1] disconnected

<7> [268.353638] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2]

<7> [268.353641] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:414:DP-2]

<7> [268.353766] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:414:DP-2] disconnected

<7> [268.353776] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3]

<7> [268.353779] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:422:DP-3]

<7> [268.353902] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:422:DP-3] disconnected

<6> [268.354154] [IGT] kms_rotation_crc: starting subtest multiplane-rotation-cropping-bottom

<7> [268.355436] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0

<7> [268.355512] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [268.355572] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.355652] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.355715] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.355792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 0 num active planes 0

<7> [268.355881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400

<7> [268.355967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400

<7> [268.356053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [268.356139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [268.356225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0

<7> [268.356536] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.356720] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [268.356851] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2

<7> [268.382758] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A

<7> [268.383223] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A

<7> [268.383671] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:393:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [268.383925] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:392:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000

<7> [268.384156] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000

<7> [268.384383] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation

<7> [268.384571] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [268.384836] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:392:DDI A/PHY A] [CRTC:151:pipe A]

<7> [268.385134] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:151:pipe A] enable: yes [fastset]

<7> [268.385418] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [268.385673] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [268.385917] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>

<7> [268.386156] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [268.386393] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0

<7> [268.387207] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0

<7> [268.387461] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64

<7> [268.387754] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [268.388006] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled

<7> [268.388314] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled

<7> [268.388563] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled

<7> [268.388871] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0

<7> [268.389172] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [268.389407] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8

<7> [268.389650] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB

<7> [268.389887] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB

<7> [268.390107] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0

<7> [268.390328] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range

<7> [268.390538] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined

<7> [268.390836] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1

<7> [268.391065] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0

<7> [268.391258] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97

<7> [268.391450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906

<7> [268.391643] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0

<7> [268.391856] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [268.392045] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [268.392221] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [268.392389] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [268.392551] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [268.393156] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855

<7> [268.393307] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0

<7> [268.393453] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [268.393623] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [268.393783] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0

<7> [268.393921] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no

<7> [268.394057] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,

<7> [268.394191] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.

<7> [268.394320] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:

<7> [268.394447] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21

<7> [268.394574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1

<7> [268.394723] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0

<7> [268.394862] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0

<7> [268.395004] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1

<7> [268.395120] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23

<7> [268.395241] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [268.395353] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [268.395464] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [268.395572] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [268.396023] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [268.396134] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [268.396240] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [268.396343] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [268.396444] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [268.396542] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [268.396653] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [268.396749] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [268.396845] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0

<7> [268.399930] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:393:eDP-1]

<7> [268.400089] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:151:pipe A]

<7> [268.419749] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [268.420117] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [268.420404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [268.449877] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:429]

<7> [268.472308] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026

<7> [268.472610] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025

<7> [268.472824] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.473021] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [268.473211] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [268.473434] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [268.473670] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.473847] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [268.474021] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [268.474188] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [268.474413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [268.474720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [268.474991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [268.475256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [268.475517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [268.475836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [268.476650] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.476922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [268.477682] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [268.477927] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:35:plane 1A]

<7> [268.482185] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1

<7> [268.484259] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:450]

<7> [268.532728] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:451]

<7> [268.533837] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [268.534285] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [268.534684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [268.549919] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [268.550257] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [268.550474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.550721] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [268.550921] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [268.551101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [268.551339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [268.551604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [268.551843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [268.552069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [268.552282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [268.552480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [268.552904] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 43464 kHz

<7> [268.553446] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.553736] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [268.583250] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:452]

<7> [268.583646] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [268.584079] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [268.584443] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [268.602113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [268.602363] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [268.602531] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [268.602840] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [268.603003] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.603149] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [268.603287] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [268.603417] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [268.603563] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.603920] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [268.604047] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [268.604154] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [268.604279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [268.604443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [268.604604] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [268.604755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [268.604901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [268.605042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [268.605480] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.605623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [268.616771] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:453]

<7> [268.631036] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [268.650059] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [268.650538] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [268.651066] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:454]

<7> [268.650983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [268.667705] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [268.667914] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [268.668045] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [268.668162] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [268.668271] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.668375] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [268.668474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [268.668579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [268.668758] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.668861] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [268.668954] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [268.669048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [268.669150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [268.669281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [268.669406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [268.669530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [268.669667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [268.669784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [268.670252] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.670368] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [268.683497] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:455]

<7> [268.697814] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [268.716131] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:456]

<7> [268.717625] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [268.718075] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [268.718467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [268.731133] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [268.731352] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [268.731515] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [268.731699] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.731838] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [268.731974] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [268.732104] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [268.732245] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [268.732382] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.732499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.732650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.732790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [268.732960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [268.733118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [268.733274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [268.733418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [268.733562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [268.734069] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.734211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [268.766121] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:457]

<7> [268.767631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [268.768147] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [268.768644] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [268.790448] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [268.790644] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [268.790762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.790873] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [268.790985] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [268.791089] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [268.791207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [268.791360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [268.791500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [268.791636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [268.791758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [268.791878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [268.792280] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.792400] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [268.816637] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [268.816978] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:458]

<7> [268.817220] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [268.817728] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [268.837934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [268.838220] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [268.838394] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [268.838552] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [268.838748] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.838895] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [268.839031] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [268.839184] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [268.839331] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.839451] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [268.839571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [268.839744] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [268.839896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [268.840076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [268.840246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [268.840410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [268.840568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [268.840748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [268.841441] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.841605] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [268.850027] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:459]

<7> [268.863166] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [268.883174] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [268.883553] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [268.884009] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:460]

<7> [268.883946] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [268.899264] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [268.899506] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [268.899664] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [268.899782] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [268.899894] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.899999] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [268.900101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [268.900209] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [268.900319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.900426] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [268.900515] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [268.900616] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [268.900719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [268.900936] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [268.901059] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [268.901159] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [268.901254] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [268.901348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.901439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [268.901531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [268.901760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [268.901856] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.901950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [268.902023] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [268.902092] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [268.902166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [268.902282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [268.902393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [268.902500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [268.902630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [268.902739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [268.903140] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.903241] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [268.916906] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:461]

<7> [268.932563] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [268.932707] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [268.932845] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [268.932956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [268.933050] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.933160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [268.966422] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:462]

<7> [268.966763] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [268.967321] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [268.967820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [268.987278] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [268.987396] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [268.987490] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [268.987595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.987686] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [268.987776] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [268.987864] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [268.987942] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [268.988013] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.988082] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.988154] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.988239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [268.988390] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [268.988454] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [268.988513] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [268.988572] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [268.988668] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [268.988739] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [268.988808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [268.988876] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [268.988932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.988983] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.989035] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [268.989096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [268.989191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [268.989277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [268.989362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [268.989444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [268.989526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [268.989880] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [268.989994] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.016171] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:463]

<7> [269.016655] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.017210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.017690] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.037761] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [269.037875] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [269.037969] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.038056] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.038124] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [269.038190] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [269.038268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [269.038415] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [269.038486] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [269.038554] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.039313] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.039376] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [269.039433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [269.039494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [269.039639] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [269.039722] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [269.039802] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.039881] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.039946] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [269.040000] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [269.040058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [269.040153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [269.040249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [269.040333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [269.040416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [269.040499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [269.040821] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.040932] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.066559] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:464]

<7> [269.066662] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.067045] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.067364] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.085615] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.085806] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [269.085943] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [269.086054] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [269.086152] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.086249] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.086341] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [269.086430] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [269.086517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.086627] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.086711] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [269.086794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [269.086891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [269.087117] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.087225] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [269.087310] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [269.087387] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [269.087458] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.087527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.087609] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [269.087679] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [269.087746] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.087817] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.087895] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [269.087962] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [269.088031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [269.088139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [269.088241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [269.088340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [269.088438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [269.088535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [269.088995] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.089089] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.099642] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:465]

<7> [269.113206] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.132612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.133077] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:466]

<7> [269.132973] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.133267] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.147969] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.148173] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [269.148280] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [269.148380] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [269.148475] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.148568] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.148961] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [269.149056] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [269.149141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.149225] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.149308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [269.149390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [269.149494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [269.149693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [269.149814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [269.149928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [269.150029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [269.150127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [269.150602] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.150717] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.166881] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:467]

<7> [269.182162] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.215957] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:468]

<7> [269.216774] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.217226] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.217619] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.234242] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026

<7> [269.234438] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025

<7> [269.234627] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [269.234783] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.234933] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [269.235075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [269.235232] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [269.235385] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [269.235511] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [269.235745] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [269.235866] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [269.236008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [269.236211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [269.236384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [269.236539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [269.236715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [269.236863] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [269.237261] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.237415] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.249531] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:469]

<7> [269.299126] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:470]

<7> [269.299649] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.300114] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.300457] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.317740] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [269.318014] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [269.318175] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.318326] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [269.318475] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [269.318759] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [269.318921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [269.319130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [269.319306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [269.319475] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [269.319669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [269.319823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [269.320298] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.320450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.349632] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:471]

<7> [269.349638] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.350046] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.350359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.369846] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.370189] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [269.370428] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [269.370702] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [269.370912] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.371116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [269.371319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [269.371517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [269.371801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.371997] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [269.372192] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [269.372424] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [269.372698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [269.373008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [269.373281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [269.373557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [269.373869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [269.374188] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [269.375013] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.375287] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.382965] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:472]

<7> [269.389648] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.389849] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.390009] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.390238] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [269.390239] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [269.390239] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [269.398595] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.399421] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.399931] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.433357] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:473]

<7> [269.433627] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.434094] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.434506] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.456526] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.456835] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [269.456991] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [269.457131] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [269.457261] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.457384] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [269.457502] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [269.457658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [269.457791] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.457900] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [269.458008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [269.458122] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [269.458237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [269.458391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [269.458538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [269.458695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [269.458854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [269.459008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [269.459486] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.459618] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.467508] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:474]

<7> [269.482210] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.517482] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.517750] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:475]

<7> [269.517974] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.518397] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.533547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [269.533747] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [269.533880] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [269.534003] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.534118] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [269.534231] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [269.534353] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [269.534475] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [269.534602] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [269.534704] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [269.534803] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [269.534934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [269.535105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [269.535257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [269.535391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [269.535518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [269.535695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [269.536097] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.536222] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.580016] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.580209] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:476]

<7> [269.580228] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.580366] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.588823] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [269.588981] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [269.589079] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.589167] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [269.589252] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [269.589337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [269.589445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [269.589712] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [269.589815] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [269.589911] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.590006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [269.590102] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [269.590195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [269.590298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [269.590462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [269.590639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [269.590801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [269.590958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [269.591124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [269.591822] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.592002] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.617626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.618142] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:477]

<7> [269.618222] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.618701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.645229] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.645628] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [269.645787] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [269.645922] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [269.646054] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.646185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [269.646312] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [269.646431] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [269.646557] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.646712] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [269.646840] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [269.646939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [269.647097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [269.647460] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.647624] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [269.647722] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [269.647824] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [269.647908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.647996] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [269.648081] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [269.648164] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [269.648247] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.648330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [269.648411] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [269.648520] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [269.648619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [269.648753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [269.648880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [269.649002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [269.649117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [269.649230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [269.649850] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.649974] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.691034] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.691188] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.691297] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.691645] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:478]

<7> [269.704748] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.705388] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.705522] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.733633] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.733964] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.734226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.737469] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:479]

<7> [269.763163] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.763511] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [269.763771] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [269.763961] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [269.764132] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.764298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [269.764451] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [269.764646] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [269.764792] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.764935] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [269.765068] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [269.765192] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [269.765338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [269.765718] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.765867] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [269.765984] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [269.766094] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [269.766196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.766297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [269.766398] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [269.766494] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [269.767011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.767110] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [269.767202] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [269.767291] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [269.767385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [269.767527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [269.767722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [269.767855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [269.767980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [269.768102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [269.768683] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.768808] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.801286] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.801442] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.801545] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.801589] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:480]

<7> [269.809643] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.810003] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.810114] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.832610] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.832952] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.833120] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:481]

<7> [269.833187] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.845828] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [269.846013] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [269.846147] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [269.846277] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.846402] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.846522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [269.846794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [269.846936] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [269.847053] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [269.847159] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [269.847258] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [269.847378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [269.847532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [269.847756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [269.847911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [269.848045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [269.848172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [269.848646] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.848786] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.882525] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:482]

<7> [269.882639] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.883111] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.883531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.902415] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [269.902753] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [269.903009] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.903252] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.903488] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [269.903960] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [269.904223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [269.904552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [269.904919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [269.905246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [269.905568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [269.906099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [269.907036] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.907323] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.933152] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:483]

<7> [269.933636] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.934112] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.934495] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.956070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.956494] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [269.956848] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [269.957099] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [269.957336] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.957558] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.957829] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [269.958039] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [269.958269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [269.958457] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [269.958674] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [269.958861] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [269.959107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [269.959380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [269.959633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [269.959898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [269.960124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [269.960333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [269.961164] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.961358] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [269.966516] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:484]

<7> [269.982635] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [269.983006] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [269.983298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [269.983806] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [269.984845] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [269.985164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.016538] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:485]

<7> [270.016647] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.016998] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.017338] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.040095] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.040444] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [270.040805] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [270.041043] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [270.041271] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.041493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [270.041756] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [270.041976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [270.042251] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.042464] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [270.042710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [270.042899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [270.043111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [270.043376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [270.043638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [270.043877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.044111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.044333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [270.045214] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.045420] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.050081] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:486]

<7> [270.067467] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.067694] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.067942] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.068138] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.068319] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.068488] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.098778] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691

<7> [270.099008] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360

<7> [270.099213] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [270.099409] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.099667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.099650] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.099925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.099972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.100130] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.100250] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.100328] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.100521] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.100773] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.101004] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.101201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [270.101388] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.101596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.101784] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.102051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [270.102351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [270.102659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [270.102960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.103266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.103568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [270.104457] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.104799] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.148824] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [270.149090] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [270.149296] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.149485] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.149718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.149889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.149839] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.150101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [270.150171] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.150368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [270.150441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.150638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [270.150892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.151144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.151389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [270.152065] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.152323] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.182378] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:487]

<7> [270.182727] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.183103] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.183407] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.200519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.201050] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [270.201277] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [270.201487] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [270.201900] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.202097] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.202275] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.202448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.202641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.202808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [270.202982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [270.203156] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [270.203346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [270.203612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [270.203866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [270.204101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [270.204324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [270.204539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [270.205265] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.205475] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.215767] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.248747] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.249015] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [270.249249] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [270.249436] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [270.249664] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.249676] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.249856] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.250042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.250027] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.250264] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.250325] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.250453] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.250665] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.250833] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.250997] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.251214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [270.251597] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.251810] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [270.252027] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [270.252203] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [270.252372] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.252537] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.252814] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.253012] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.253209] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.253376] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.253545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.253786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.253981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [270.254292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [270.254615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [270.254952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [270.255277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [270.255620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [270.256105] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 43464 kHz -> 65196 kHz

<7> [270.257111] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.257447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.265597] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.298803] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [270.299043] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [270.299252] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [270.299451] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.299698] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.299891] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.299831] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.300107] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.300207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.300290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [270.300470] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.300499] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.300711] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.300890] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.301080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [270.301448] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [270.301652] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [270.301831] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [270.302006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.302216] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.302400] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.302565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.302797] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [270.302974] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.303148] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.303358] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.303592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [270.303879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [270.304168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [270.304450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.304800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.305117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [270.306014] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.306324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.332035] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [270.332282] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [270.332491] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.332746] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.332926] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.332892] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.333119] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.333220] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.333313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [270.333487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.333706] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [270.333881] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [270.334055] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.334226] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.334396] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.334562] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.334789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [270.335143] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [270.335299] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [270.335452] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.335628] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.335789] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.335947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.336118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [270.336441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [270.336736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [270.336996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.337256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.337568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [270.338400] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.338686] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.365395] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.365765] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [270.365843] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.365981] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [270.366177] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [270.366192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.366368] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.366485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.366553] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.366795] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.366993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.367203] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.367393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [270.367565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [270.367794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [270.367991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [270.368452] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.368693] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [270.368888] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [270.369053] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [270.369214] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.369372] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.369553] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.369816] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.369991] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.370153] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [270.370312] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [270.370471] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [270.370671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [270.370938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [270.371189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [270.371433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [270.371715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [270.372052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [270.373100] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.373347] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.382000] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.415343] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.415661] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [270.415687] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.415861] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [270.416045] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [270.416015] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.416226] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.416288] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.416404] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.416595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.416785] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.416982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.417160] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.417338] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.417513] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.417762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [270.418027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [270.418286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [270.418543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [270.418835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [270.419097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [270.420082] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.420356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.432385] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.465500] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [270.465772] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [270.465909] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.465984] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [270.466188] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.466260] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.466385] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [270.466543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.466598] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [270.466796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [270.466975] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [270.467147] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.467321] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.467505] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.467731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [270.467991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [270.468251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [270.468504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.468781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.469025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [270.469754] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.470018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.498714] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [270.498921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [270.499105] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.499286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [270.499485] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [270.499711] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [270.499833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.499919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [270.500185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [270.500185] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.500452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [270.500479] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.500744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.500989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.501228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [270.502015] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.502285] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.531978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.532227] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [270.532411] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [270.532624] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [270.532800] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.532774] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.532971] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [270.533102] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.533171] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [270.533351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [270.533376] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.533511] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.533698] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [270.533856] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [270.534010] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [270.534187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [270.534437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [270.534716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [270.534968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [270.535222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [270.535524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [270.536507] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.536801] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.548889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.581948] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.582192] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [270.582374] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [270.582549] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [270.582789] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.582956] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [270.582886] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.583116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [270.583274] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [270.583216] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.583428] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.583489] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.583596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [270.583757] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [270.583916] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [270.584130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [270.584398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [270.584664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [270.584909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [270.585196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [270.585435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [270.586368] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.586687] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.598901] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.631967] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691

<7> [270.632176] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360

<7> [270.632363] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0

<7> [270.632543] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.632789] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.632958] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.632938] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.633156] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.633270] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.633334] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [270.633490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.633545] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.633679] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.633836] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.634048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [270.634313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [270.634562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [270.634852] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.635101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.635349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [270.636048] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.636317] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.665312] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [270.665501] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [270.665730] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.665903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.665874] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.666086] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.666278] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.666255] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.666466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [270.666541] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.666749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [270.666993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [270.667243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.667482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.667754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [270.668387] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.668650] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.698642] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.698864] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [270.699062] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [270.699220] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [270.699376] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.699531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.699754] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.699940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.699881] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.700095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.700251] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [270.700207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.700407] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [270.700483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.700558] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [270.700791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [270.701198] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.701400] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [270.701559] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [270.701786] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [270.701941] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.702091] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.702270] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.702439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.703144] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.703288] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [270.703426] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [270.703565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [270.703777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [270.704028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [270.704274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [270.704518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [270.704793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [270.705069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [270.705792] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.706050] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.715453] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.748691] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.748971] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [270.749180] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [270.749376] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [270.749596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.749787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.749716] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.749976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.750071] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.750204] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.750364] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.750413] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.750661] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.750844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.751009] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.751195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [270.751547] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.751787] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [270.751983] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [270.752163] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [270.752323] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.752483] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.752679] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.752879] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.753042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.753200] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.753359] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.753516] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.753740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [270.754045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [270.754307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [270.754580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [270.754847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [270.755107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [270.755973] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.756236] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.765358] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.798639] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [270.798860] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [270.799050] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [270.799230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.799405] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.799607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.799787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.799738] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.800005] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [270.800092] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.800194] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.800393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.800385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.800580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.800774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [270.801232] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [270.801412] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [270.801588] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [270.801755] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.801953] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.802141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.802350] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.802544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [270.802762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.802934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.803099] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.803273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [270.803542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [270.803846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [270.804161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.804423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.804717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [270.805516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.805829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.831952] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [270.832191] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [270.832390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.832609] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.832801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.832748] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.833028] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.833099] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.833251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [270.833392] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.833531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [270.833847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [270.834110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.834366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [270.834647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [270.835425] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.835735] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.865264] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.865518] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [270.865780] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [270.865816] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.865968] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [270.866150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.866164] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.866327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.866453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.866496] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.866756] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.866942] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.867163] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [270.867360] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [270.867533] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [270.867791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [270.868105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [270.868409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [270.868712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [270.869022] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [270.869305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [270.870409] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.870722] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.882284] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.915237] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.915506] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [270.915899] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [270.915898] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.916109] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [270.916249] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.916308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.916499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [270.916543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.916776] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [270.916959] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [270.917161] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.917326] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [270.917491] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [270.917690] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [270.917916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [270.918209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [270.918486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [270.918786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [270.919038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [270.919281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [270.920260] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.920529] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.932134] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [270.965434] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [270.965707] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [270.965828] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.965902] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [270.966085] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.966157] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [270.966262] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [270.966452] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [270.966431] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [270.966681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [270.966865] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [270.967043] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.967223] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.967424] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [270.967650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [270.967915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [270.968177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [270.968438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.968717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [270.969003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [270.969765] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [270.970023] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [270.989630] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 turning VDD off

<7> [270.989873] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:392:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067

<7> [270.998658] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [270.998877] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [270.999066] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [270.999251] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [270.999439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [270.999681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [270.999713] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [270.999917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [271.000132] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.000227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [271.000471] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.000534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [271.000876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [271.001178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [271.001451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [271.002262] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.002548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.031893] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [271.032139] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [271.032322] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [271.032497] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [271.032727] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.032890] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.032849] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.033080] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [271.033179] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.033254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [271.033415] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.033452] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.033587] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.033745] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [271.033903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [271.034086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [271.034358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [271.034634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [271.034964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [271.035243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [271.035651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [271.036615] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.036909] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.048652] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [271.081864] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [271.082115] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [271.082331] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [271.082508] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [271.082742] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.082907] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.082878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.083070] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [271.083230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [271.083210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.083394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.083485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.083604] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.083775] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [271.083943] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [271.084135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [271.084408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [271.084699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [271.084994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [271.085235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [271.085473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [271.086422] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.086714] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.098709] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [271.131918] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.132195] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597

<7> [271.132425] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293

<7> [271.132664] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161

<7> [271.132841] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.132783] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.133011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.133119] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.133180] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.133358] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.133395] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.133515] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.133710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.133874] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.134037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.134202] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.134366] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.134526] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [271.134751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [271.134965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [271.135373] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.135617] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597

<7> [271.135807] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293

<7> [271.135994] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161

<7> [271.136171] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.136345] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.136519] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.136958] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.137200] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.137393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.137673] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.137882] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.138067] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.138243] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.138421] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [271.138631] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [271.138830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [271.139144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [271.139454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [271.139780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [271.140083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [271.140377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [271.141398] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.141742] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.148286] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:35:plane 1A]

<7> [271.148725] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [271.148919] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [271.165640] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.198684] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.198983] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [271.199199] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [271.199406] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [271.199658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.199848] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [271.199784] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.200038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [271.200139] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.200261] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [271.200426] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.200510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [271.200970] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.201198] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [271.201373] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [271.201545] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [271.201762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.201940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [271.202122] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [271.202337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [271.202546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [271.202875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [271.203132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [271.203377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [271.203639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [271.203942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [271.204723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.204994] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.248728] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.249357] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.249752] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.249878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.250157] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [271.250354] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.250467] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [271.250780] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [271.250806] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.251013] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [271.251236] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.251456] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.251718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.251950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.252162] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.252372] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [271.252630] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [271.252846] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [271.253090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [271.253434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [271.253824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [271.254202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [271.254582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [271.254926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [271.256174] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.256527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.264936] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [271.282680] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.283039] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.315229] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.315466] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.315748] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [271.315841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.315999] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [271.316198] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [271.316196] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.316386] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [271.316481] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.316602] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.316789] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [271.316985] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [271.317208] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [271.317385] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.317559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.317792] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.317990] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.318216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [271.318716] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.318931] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.319155] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [271.319366] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [271.319535] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [271.319778] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [271.319989] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.320169] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [271.320332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [271.320524] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [271.320747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.320908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.321075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.321256] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.321420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [271.321722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [271.322011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [271.322272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [271.322577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [271.322826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [271.323711] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.323977] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.332138] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.332321] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.365637] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:488]

<7> [271.365729] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.366183] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.366615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.385951] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.386325] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [271.386764] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [271.387022] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [271.387270] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [271.387517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.387819] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.388056] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.388320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.388537] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [271.388803] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.389006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.389210] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.389459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [271.389780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [271.390057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [271.390313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [271.390569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [271.390814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [271.391862] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.392091] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.392575] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [271.392757] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [271.398909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.431924] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.432278] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [271.432541] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [271.432905] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [271.433030] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.433173] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.433491] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [271.433508] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.433811] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [271.434000] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.434123] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [271.434451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [271.434894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [271.435289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [271.435668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [271.436084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [271.436458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [271.437615] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.438010] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.481999] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.482361] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.482764] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [271.482832] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.483018] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [271.483265] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [271.483268] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.483495] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [271.483664] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.483778] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.483999] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.484217] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.484459] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.484718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.484934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [271.485161] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [271.485394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [271.485705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [271.486057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [271.486427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [271.486812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [271.487163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [271.487462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [271.488791] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.489125] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.498257] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [271.515856] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.516144] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.548626] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.548968] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.549334] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [271.549707] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [271.549846] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.549970] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [271.550222] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [271.550365] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.550468] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.550778] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [271.550806] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.551056] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [271.551297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [271.551535] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.551902] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.552155] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.552396] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.552725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [271.553150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [271.553534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [271.553962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [271.554376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [271.554759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [271.556120] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.556462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.565485] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.565700] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.599093] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:489]

<7> [271.599738] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.600182] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.600537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.619113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.619434] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [271.619706] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [271.619929] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [271.620148] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [271.620365] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.620740] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.620947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [271.621200] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [271.621424] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [271.621654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.621836] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.622011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.622212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [271.622474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [271.622746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [271.622985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [271.623217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [271.623465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [271.624423] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.624670] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.625139] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [271.625301] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [271.632210] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.665240] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.665698] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [271.665768] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.666071] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [271.666294] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.666372] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [271.666709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.666777] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.666997] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.667285] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [271.667559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [271.667951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [271.668548] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.668938] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [271.669210] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [271.669485] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [271.669824] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.670095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.670357] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [271.670751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [271.671009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [271.671389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [271.671801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [271.672230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [271.672601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [271.672990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [271.674013] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.674356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.715313] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.715838] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.715841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.716144] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.716271] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.716496] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [271.716680] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.716866] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [271.717112] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [271.717344] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [271.717603] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.717831] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.718054] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [271.718301] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [271.718520] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.718792] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.719005] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [271.719214] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [271.719457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [271.719832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [271.720185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [271.720533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [271.720952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [271.721253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [271.722501] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.722876] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.731539] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [271.749349] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.749739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.782033] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.782318] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.782639] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [271.782737] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.782899] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [271.783118] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [271.783144] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.783330] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [271.783476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.783541] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.783813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.784068] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [271.784281] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [271.784481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.784735] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [271.784976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [271.785188] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [271.785437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [271.785799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [271.786170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [271.786487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [271.786853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [271.787214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [271.788382] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.788727] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.798767] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.798954] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.831877] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.832222] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597

<7> [271.832474] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293

<7> [271.832795] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161

<7> [271.832945] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.833036] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [271.833322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.833384] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.833577] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.833838] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.833817] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.834047] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.834252] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [271.834460] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.834716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.834940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.835205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [271.835784] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.836056] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597

<7> [271.836304] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293

<7> [271.836516] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161

<7> [271.836773] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [271.836983] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.837183] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.837416] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.837664] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.837873] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [271.838069] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.838269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.838465] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [271.838718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [271.839019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [271.839350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [271.839698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [271.840009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [271.840315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [271.841225] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.841523] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.842260] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [271.842510] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [271.848775] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.881830] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.882180] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [271.882440] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [271.882753] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [271.882886] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.882981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.883201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [271.883292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.883448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [271.883702] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [271.883667] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.883948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [271.884255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [271.884573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [271.884888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [271.885197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [271.885513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [271.886400] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.886763] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.931881] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.932182] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.932461] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [271.932718] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [271.932901] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [271.932845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.933076] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [271.933180] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.933247] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.933413] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [271.933454] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.933598] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [271.933760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [271.933960] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [271.934146] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [271.934344] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [271.934506] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [271.934756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [271.935017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [271.935272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [271.935528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [271.935818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [271.936087] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [271.937034] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [271.937338] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [271.948180] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [271.965891] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.966304] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.998489] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [271.998852] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [271.999005] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [271.999173] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [271.999460] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [271.999446] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [271.999760] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [271.999852] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [271.999993] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [272.000220] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.000484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [272.000764] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [272.000992] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [272.001232] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.001462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.001729] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.001973] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.002270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [272.002676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [272.003023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [272.003368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [272.003733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [272.004102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [272.005122] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.005441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.015366] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.015588] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.048731] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.049130] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.049426] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.049759] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:490]

<7> [272.068105] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.068468] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [272.068967] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [272.069200] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [272.069416] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [272.069713] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.069920] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.070106] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.070325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.070514] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [272.070731] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.070897] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.071059] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.071250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [272.071527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [272.071806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [272.072035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [272.072260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [272.072467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [272.073421] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.073643] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.074062] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [272.074225] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [272.082228] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.115178] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.115640] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [272.115979] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [272.116274] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [272.116596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.116622] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.116884] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [272.117144] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.117198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [272.117508] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [272.117598] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.117901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [272.118331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [272.118834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [272.119289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [272.119720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [272.120141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [272.122484] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.122927] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.165290] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.165776] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.165880] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.166244] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [272.166401] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.166546] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [272.166905] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [272.166915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.167158] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [272.167403] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.167705] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.167971] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.168241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.168504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.168808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [272.169078] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [272.169299] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [272.169587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [272.170010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [272.170441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [272.170881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [272.171246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [272.171661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [272.173252] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.173646] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.181466] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [272.199244] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.199620] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.231912] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.232177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.232439] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [272.232769] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [272.232962] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [272.232902] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.233150] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [272.233258] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.233332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.233510] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [272.233576] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.233753] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [272.233988] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [272.234216] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.234433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.234656] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.234855] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.235085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [272.235412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [272.235777] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [272.236066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [272.236351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [272.236688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [272.237801] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.238110] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.248803] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.248996] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.282495] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:491]

<7> [272.282717] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.283177] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.283593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.303363] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.303710] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [272.303945] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [272.304126] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [272.304300] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [272.304462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.304686] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [272.304855] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [272.305035] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [272.305189] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [272.305330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.305460] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.305607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.305751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [272.305973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [272.306160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [272.306329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [272.306500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [272.306680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [272.307286] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.307445] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.307853] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [272.307985] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [272.315396] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.348439] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.348840] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [272.348811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.349127] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [272.349281] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.349369] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [272.349659] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.349673] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.349929] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [272.350170] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [272.350408] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [272.350727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [272.351103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [272.351472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [272.351884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [272.352247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [272.352637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [272.353698] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.354073] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.398487] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.398952] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.398985] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.399360] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [272.399466] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.399692] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [272.399964] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [272.399918] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.400219] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [272.400529] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.400850] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [272.401129] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [272.401405] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [272.401689] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.401922] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [272.402211] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [272.402451] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [272.402775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [272.403122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [272.403476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [272.403861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [272.404246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [272.404597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [272.405881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.406226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.414727] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [272.432232] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.432484] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.465042] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.465283] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.465567] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [272.465707] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.465791] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [272.465970] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [272.466047] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.466144] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [272.466316] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.466321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.466513] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [272.466741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [272.466919] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [272.467095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.467270] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [272.467450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [272.467667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [272.467868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [272.468135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [272.468397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [272.468683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [272.468978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [272.469236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [272.470254] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.470526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.481961] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.482161] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.515018] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.515319] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823

<7> [272.515590] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614

<7> [272.515706] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.515802] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614

<7> [272.516022] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [272.516122] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.516233] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.516444] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [272.516460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.516697] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [272.516921] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [272.517193] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.517416] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.517703] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.517937] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.518151] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.518366] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.518658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.518875] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.519081] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [272.519283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.519482] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.519745] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.519975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [272.520298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [272.520625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [272.520978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [272.521280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [272.521592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [272.522423] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.522745] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.523445] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [272.523728] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [272.531995] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.565086] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.565510] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [272.565972] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [272.566103] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.566255] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [272.566515] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.566613] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.566899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [272.567001] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.567168] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [272.567416] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [272.567761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [272.568137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [272.568516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [272.568949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [272.569378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [272.569785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [272.570723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.571079] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.615231] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.615721] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.615831] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.616185] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [272.616354] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.616505] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [272.616865] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [272.616872] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.617141] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [272.617414] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.617740] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.618006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.618268] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.618534] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.618773] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [272.619018] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [272.619313] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [272.619681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [272.620110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [272.620507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [272.620999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [272.621361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [272.621768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [272.623209] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.623604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.631386] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [272.649054] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.649394] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.681778] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.682110] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.682441] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [272.682849] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [272.683000] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.683111] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [272.683365] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [272.683475] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.683657] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.683926] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [272.683946] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.684174] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [272.684415] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [272.684714] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.684984] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.685230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.685472] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.685821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [272.686201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [272.686583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [272.686965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [272.687280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [272.687683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [272.688881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.689217] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.698676] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.698873] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.731884] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.732232] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823

<7> [272.732584] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614

<7> [272.732710] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.732828] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614

<7> [272.733064] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [272.733146] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.733345] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.733605] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.733551] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.733830] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.734055] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.734272] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [272.734487] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.734766] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.734993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.735243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [272.735617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [272.735979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [272.736316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [272.736690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [272.737074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [272.738412] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.738783] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.739541] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [272.739843] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [272.748559] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.781675] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.781989] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [272.782257] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [272.782467] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [272.782741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.782866] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.782948] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [272.783155] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [272.783244] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.783400] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [272.783586] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.783707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [272.784180] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.784410] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [272.784674] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [272.784853] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [272.785025] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.785230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [272.785410] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [272.786119] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [272.786332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [272.786687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [272.786971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [272.787244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [272.787527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [272.787801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [272.788651] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.788937] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.831741] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.832056] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.832404] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [272.832698] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [272.832921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [272.832838] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.833133] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [272.833242] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.833336] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.833560] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.833606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.833794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.833982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.834161] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.834337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [272.834527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [272.834700] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [272.834949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [272.835490] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.835781] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.836032] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [272.836208] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [272.836373] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [272.836573] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [272.836747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.836928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.837101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.837272] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.837442] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.837657] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [272.837867] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [272.838065] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [272.838251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [272.838555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [272.838845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [272.839116] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [272.839382] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [272.839661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [272.840788] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.841068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.848022] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [272.865362] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.865613] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.898440] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.898847] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.898973] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.899191] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [272.899450] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.899727] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [272.899928] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.900018] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [272.900268] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [272.900613] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.900898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [272.901150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [272.901395] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [272.901692] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.901964] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [272.902208] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [272.902453] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [272.902807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [272.903185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [272.903562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [272.903955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [272.904304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [272.904691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [272.906003] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.906349] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.915224] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.915410] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [272.948741] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.948672] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.949165] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826

<7> [272.949210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.949547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605

<7> [272.949688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.949826] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620

<7> [272.950087] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [272.950341] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [272.950695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [272.950925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [272.951154] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [272.951401] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [272.951680] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.951908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.952135] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [272.952402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [272.952835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [272.953208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [272.953565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [272.953902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [272.954232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [272.955419] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [272.955800] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [272.956640] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [272.956938] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [272.965199] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.998537] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [272.998680] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [272.999011] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [272.999175] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [272.999525] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [272.999602] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289

<7> [272.999935] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164

<7> [273.000254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.000597] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.000932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [273.001195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [273.001521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [273.001943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [273.002358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [273.002860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [273.003277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [273.003700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [273.004922] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.005339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.048465] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.048960] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.049380] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913

<7> [273.049827] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452

<7> [273.049973] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.050115] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794

<7> [273.050375] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892

<7> [273.050449] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.050719] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.050962] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.050917] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.051201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [273.051511] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [273.051750] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.051973] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.052198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [273.052419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [273.052817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [273.053208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [273.053594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [273.053979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [273.054339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [273.054788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [273.056211] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.056573] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.064630] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [273.082132] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.082399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.114983] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.115313] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.115719] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691

<7> [273.115811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.116015] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676

<7> [273.116276] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350

<7> [273.116286] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.116571] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334

<7> [273.116740] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.116879] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.117138] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.117388] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [273.117691] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [273.117934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.118172] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.118477] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [273.118807] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [273.119068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [273.119422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [273.119811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [273.120201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [273.120573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [273.120905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [273.122255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.122625] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.131920] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.132121] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.164895] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.165181] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 691) -> ( 0 - 823), size 691 -> 823

<7> [273.165383] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 691 - 1367) -> ( 823 - 2437), size 676 -> 1614

<7> [273.165646] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2717) -> (2437 - 4051), size 1350 -> 1614

<7> [273.165833] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0

<7> [273.165767] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.166006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.166098] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.166178] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.166347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.166375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.166583] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.166759] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [273.166938] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.167117] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.167292] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.167522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [273.167862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [273.168161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [273.168456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [273.168827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [273.169112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [273.169984] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.170286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.171066] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [273.171329] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [273.181884] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.214995] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.215318] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [273.215614] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [273.215823] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [273.215753] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.216022] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.216113] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.216211] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [273.216399] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [273.216398] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.216676] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [273.216953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [273.217421] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.217699] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [273.217909] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [273.218108] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [273.218316] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.218565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [273.218795] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [273.218998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [273.219206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [273.219544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [273.219899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [273.220211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [273.220535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [273.220894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [273.221741] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.222060] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.265021] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.265403] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.265714] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.265751] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.266032] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [273.266149] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.266245] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [273.266443] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [273.266462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.266691] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [273.266894] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.267097] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.267318] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.267584] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.267800] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.268007] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [273.268215] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [273.268421] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [273.268733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [273.269114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [273.269518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [273.269890] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [273.270261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [273.270669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [273.271939] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.272316] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.281299] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [273.299177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.299545] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.331632] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.331907] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.332173] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [273.332407] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [273.332688] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [273.332815] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.332908] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [273.333119] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.333220] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.333326] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [273.333606] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [273.333589] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.333844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [273.334045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.334246] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.334452] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.334716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.334953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [273.335498] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.335741] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.335984] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [273.336231] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [273.336427] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [273.336737] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [273.336947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.337154] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [273.337341] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [273.337562] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [273.337747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.337969] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.338169] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.338388] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.338627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [273.338946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [273.339273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [273.339601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [273.339901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [273.340194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [273.341158] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.341485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.348526] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.348719] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.381628] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.381920] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823

<7> [273.382158] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614

<7> [273.382350] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614

<7> [273.382595] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [273.382786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.382728] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.382973] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.383084] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.383172] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.383389] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.383374] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.383612] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [273.383788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.383965] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.384135] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.384332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [273.384692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [273.384958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [273.385220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [273.385484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [273.385743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [273.386891] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.387177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.387801] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [273.388076] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [273.398519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.431572] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.431912] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [273.432208] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [273.432498] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [273.432644] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.432747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.432972] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [273.433059] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.433211] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [273.433400] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.433453] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [273.433779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [273.434102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [273.434415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [273.434760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [273.435074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [273.435387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [273.436351] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.436707] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.481714] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.482078] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.482416] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [273.482764] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [273.482903] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.483006] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [273.483237] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [273.483341] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.483487] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.483713] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.483753] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.483939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.484196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.484408] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.484674] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [273.484879] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [273.485083] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [273.485322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [273.485721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [273.486060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [273.486402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [273.486784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [273.487117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [273.488772] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.489118] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.497920] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [273.515819] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.516293] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.548383] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.548897] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.548972] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.549316] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [273.549529] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.549745] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [273.549952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.550016] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [273.550273] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [273.550567] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.550813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [273.551091] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [273.551351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [273.551634] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.551877] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.552130] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.552370] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.552728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [273.553104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [273.553488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [273.553858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [273.554228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [273.554689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [273.556217] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.556618] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.565206] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.565414] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.598403] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.598771] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826

<7> [273.598855] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.599013] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605

<7> [273.599208] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620

<7> [273.599212] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.599395] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [273.599546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.599635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.599818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.600009] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [273.600228] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [273.600408] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [273.600633] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.600818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.601004] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.601243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [273.601601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [273.601904] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [273.602218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [273.602614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [273.602928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [273.603959] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.604286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.605050] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [273.605335] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [273.615062] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.648172] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.648512] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [273.648617] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.648778] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289

<7> [273.648986] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164

<7> [273.648973] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.649196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.649284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.649402] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.649658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [273.649876] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [273.650179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [273.650566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [273.650894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [273.651210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [273.651546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [273.651879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [273.652742] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.653068] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.698376] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.698939] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.699268] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.699700] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913

<7> [273.699786] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.700028] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452

<7> [273.700287] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794

<7> [273.700304] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.700580] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892

<7> [273.700747] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.700826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.701064] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.701328] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [273.701655] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [273.701887] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.702109] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.702337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [273.702615] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [273.702876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [273.703250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [273.703660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [273.704073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [273.704426] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [273.704848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [273.706263] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.706676] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.714521] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [273.732613] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.732997] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.764992] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.765255] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.765567] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691

<7> [273.765554] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.765839] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676

<7> [273.765943] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.766068] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350

<7> [273.766284] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334

<7> [273.766276] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.766536] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.766754] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.766991] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [273.767234] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [273.767462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.767677] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [273.767889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [273.768085] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [273.768319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [273.768647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [273.768984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [273.769270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [273.769595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [273.769878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [273.770986] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.771268] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.781896] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [273.782086] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [273.814825] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 691) -> ( 0 - 2026), size 691 -> 2026

<7> [273.815052] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 691 - 1367) -> (2026 - 4051), size 676 -> 2025

<7> [273.815238] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2717) -> ( 0 - 0), size 1350 -> 0

<7> [273.815417] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0

<7> [273.815668] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.815689] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.815859] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.816063] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.816042] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.816283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.816334] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.816508] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.816685] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.816870] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.817050] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.817230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [273.817406] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.817650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.817866] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.818071] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [273.818274] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.818493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.818686] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.818906] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [273.819476] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 691) -> ( 0 - 2026), size 691 -> 2026

<7> [273.819661] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 691 - 1367) -> (2026 - 4051), size 676 -> 2025

<7> [273.819840] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2717) -> ( 0 - 0), size 1350 -> 0

<7> [273.820012] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0

<7> [273.820195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.820361] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.820576] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.820737] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.820897] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.821062] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.821230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.821402] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.821626] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [273.821781] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.821982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.822160] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.822323] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [273.822494] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.822644] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.822785] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.822935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [273.823187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [273.823458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [273.823706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [273.823982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [273.824238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [273.825063] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.825320] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.825945] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [273.826193] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:35:plane 1A]

<7> [273.848016] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [273.848150] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [273.848239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.848320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [273.848401] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [273.848514] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [273.848608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [273.848646] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.848727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [273.848811] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.848847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [273.848936] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.848964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [273.849074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [273.849181] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [273.849557] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.849688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.881631] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [273.882098] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [273.882494] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [273.882628] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.882793] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [273.883067] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.883148] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.883322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.883624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.883588] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.883875] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.884115] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.884347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [273.884643] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [273.884874] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [273.885171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [273.885592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [273.885961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [273.886327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [273.886722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [273.887078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [273.888340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.888747] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.898396] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [273.931468] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [273.931769] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [273.931996] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [273.932194] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [273.932385] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.932695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [273.932811] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.932901] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [273.933096] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [273.933191] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.933277] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.933481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.933513] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.933658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.933834] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.934043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [273.934353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [273.934656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [273.934924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [273.935197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [273.936048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [273.936927] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.937204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [273.948332] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [273.981529] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [273.981759] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [273.981963] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [273.982157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [273.982344] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [273.982582] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [273.982708] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [273.982777] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [273.982953] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [273.983036] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [273.983121] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.983287] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.983301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [273.983478] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [273.983674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [273.983977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [273.984239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [273.984507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [273.984762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [273.985014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [273.985777] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [273.986040] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.014749] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [274.014966] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [274.015135] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.015301] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [274.015527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [274.015541] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.015704] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [274.015872] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.015891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [274.016131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [274.016147] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.016373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [274.016646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.016936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.017174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [274.017904] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.018160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.048096] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.048344] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [274.048634] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [274.048811] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [274.048758] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.048977] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.049141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.049089] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.049306] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.049365] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.049534] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.049709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.049874] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [274.050040] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [274.050241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [274.050460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [274.050731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [274.050980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [274.051227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [274.051490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [274.051741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [274.052749] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.053002] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.064870] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.098076] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.098336] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [274.098585] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [274.098772] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [274.098707] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.098957] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.099059] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.099135] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [274.099311] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [274.099349] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.099563] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [274.099733] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.099888] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.100044] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.100196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.100371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [274.100657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [274.100929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [274.101196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.101524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.101803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [274.102882] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.103155] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.114956] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.148547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [274.148581] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.148788] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [274.148919] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.148983] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [274.149163] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.149190] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.149338] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.149546] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [274.149717] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [274.149909] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [274.150080] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.150249] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.150425] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.150619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [274.151067] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [274.151260] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [274.151448] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [274.151619] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.151787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.151987] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [274.152152] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [274.152316] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [274.152512] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.152719] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.152950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.153149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [274.153449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [274.153732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [274.153999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [274.154261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [274.154539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [274.155351] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.155624] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.181596] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [274.181906] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [274.182136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.182344] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.182623] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [274.182761] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.182844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [274.183095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [274.183147] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.183495] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.183550] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [274.183751] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [274.183928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.184099] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.184294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [274.184499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [274.184678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [274.184930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [274.185167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [274.185402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.185720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.185937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [274.186608] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.186816] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.214865] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.215239] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [274.215617] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [274.215642] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.215855] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [274.216080] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.216045] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.216294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.216382] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.216544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [274.216756] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [274.216985] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.217187] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.217388] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [274.217641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [274.217925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [274.218382] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.218692] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [274.218876] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [274.219051] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [274.219266] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.219500] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.219712] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [274.219893] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [274.220066] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.220236] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.220448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [274.220651] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [274.220828] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [274.221117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [274.221416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [274.221693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [274.222029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [274.222283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [274.223395] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.223705] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.231447] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.264714] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.264996] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [274.265227] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [274.265465] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [274.265539] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.265661] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.265844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.265879] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.266022] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [274.266154] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.266222] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [274.266391] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.266613] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.266788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [274.266963] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [274.267169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [274.267686] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.267929] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [274.268130] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [274.268302] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [274.268492] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.268650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.268806] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [274.269006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [274.269199] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.269365] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.269578] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [274.269732] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [274.269889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [274.270189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [274.270456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [274.270712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.270969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.271282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [274.272335] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.272642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.281500] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.314720] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026

<7> [274.314952] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025

<7> [274.315159] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [274.315358] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.315619] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.315802] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.315767] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.316016] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.316099] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.316207] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [274.316373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.316435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.316622] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.316794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.316998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [274.317274] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [274.317582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [274.317850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [274.318108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [274.318425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [274.319061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.319315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.348064] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [274.348261] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [274.348486] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.348667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [274.348623] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.348846] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [274.348972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.349057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [274.349263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.349294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [274.349628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [274.349884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [274.350142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.350413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.350719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [274.351389] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.351702] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.381431] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.381689] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [274.381865] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [274.382033] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [274.382194] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.382352] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.382613] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.382796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.382735] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.382971] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.383140] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [274.383086] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.383308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [274.383375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.383508] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [274.383700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [274.383957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [274.384216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [274.384522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [274.384759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [274.385007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [274.385886] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.386143] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.398175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.431376] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.431721] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [274.431982] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [274.432182] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [274.432373] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.432626] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [274.432750] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.432815] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [274.433024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [274.433102] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.433201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.433373] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.433386] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.433601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.433787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.433996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [274.434272] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [274.434574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [274.434841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.435100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.435423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [274.436266] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.436549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.448286] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.481381] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [274.481667] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [274.481866] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [274.482055] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.482237] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.482450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.482574] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.482633] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.482845] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [274.482906] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.483030] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.483201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.483174] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.483368] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.483614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [274.483901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [274.484152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [274.484422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [274.484676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [274.484924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [274.485687] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.485957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.514676] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [274.514871] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [274.515053] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.515231] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [274.515447] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [274.515505] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.515626] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [274.515832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [274.515858] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.516093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [274.516177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.516346] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [274.516644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.516950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.517204] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [274.518002] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.518271] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.548000] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.548235] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [274.548444] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [274.548614] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [274.548571] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.548786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.548957] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.548918] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.549126] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.549211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.549323] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.549538] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.549701] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [274.549857] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [274.550012] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [274.550195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [274.550459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [274.550709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [274.550964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [274.551242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [274.551527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [274.552522] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.552778] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.564854] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.598012] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.598269] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [274.598555] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [274.598745] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [274.598693] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.598927] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.599107] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [274.599065] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.599285] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [274.599355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.599544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [274.599715] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.599874] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.600032] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.600188] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.600368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [274.600796] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.601015] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [274.601189] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [274.601360] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [274.601585] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.601751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [274.601940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [274.602101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [274.602260] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.602439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.602596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.602750] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.602931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [274.603185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [274.603446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [274.603722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.603976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.604232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [274.605241] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.605527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.615097] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.648225] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [274.648495] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [274.648523] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.648693] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [274.648884] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.648903] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.649075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.649193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.649267] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [274.649525] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [274.649710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [274.649879] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.650050] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.650217] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.650424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [274.650810] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [274.650995] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [274.651175] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [274.651347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.651580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.651752] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [274.651918] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [274.652081] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [274.652240] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.652419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.652580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.652751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [274.653028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [274.653280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [274.653559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [274.653822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [274.654083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [274.654859] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.655124] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.681447] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [274.681788] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [274.682034] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.682261] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.682602] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [274.682627] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.682822] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [274.683029] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.683079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [274.683367] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.683581] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [274.683794] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [274.683982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.684167] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.684353] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [274.684589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [274.684789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [274.685208] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [274.685426] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [274.685596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.685763] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.685964] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [274.686153] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [274.686332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [274.686620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [274.686872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [274.687104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.687332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.687577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [274.688249] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.688485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.714664] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.714966] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [274.715181] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [274.715415] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [274.715607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.715563] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.715787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.715904] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.715959] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [274.716160] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [274.716177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.716350] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.716561] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.716723] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [274.716891] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [274.717084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [274.717558] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.717764] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [274.717920] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [274.718071] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [274.718222] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.718392] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.718550] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [274.718737] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [274.718930] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.719088] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.719248] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [274.719431] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [274.719598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [274.719858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [274.720109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [274.720355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [274.720640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [274.720951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [274.721963] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.722212] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.731318] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.764651] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.764944] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [274.765203] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [274.765463] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [274.765660] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.765601] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.765843] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.765938] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.766022] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [274.766205] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.766231] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [274.766449] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.766618] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [274.766786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [274.766998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [274.767228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [274.767537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [274.767809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [274.768057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.768295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.769216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [274.770255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.770546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.781484] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.814677] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691

<7> [274.814948] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360

<7> [274.815187] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [274.815469] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.815607] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.815696] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [274.815903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [274.815989] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.816150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [274.816300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.816390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.816598] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.816786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.816964] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.817140] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [274.817343] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.817570] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.817741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [274.817949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [274.818251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [274.818580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [274.818871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.819138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [274.819415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [274.820167] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.820453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.864739] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [274.865014] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [274.865236] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.865501] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [274.865624] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.865706] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [274.865942] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [274.865994] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.866184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [274.866279] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.866489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [274.866760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [274.867030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.867293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [274.867606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [274.868299] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.868602] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.898438] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.898847] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.899137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.899408] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:492]

<7> [274.918432] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.918749] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [274.918956] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [274.919148] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [274.919325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.919829] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.920025] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.920182] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.920328] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.920516] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [274.920670] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [274.920835] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [274.921012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [274.921218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [274.921421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [274.921606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [274.921788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [274.921967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [274.922635] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.922811] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.931776] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.964665] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [274.964933] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [274.965135] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [274.965329] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [274.965601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.965638] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [274.965789] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [274.965984] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [274.965996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [274.966191] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [274.966289] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [274.966405] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [274.966577] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [274.966747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [274.966909] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [274.967096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [274.967349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [274.967645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [274.967954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [274.968215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [274.968506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [274.969444] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [274.969730] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [274.981729] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.014637] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [275.014874] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [275.015083] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [275.015283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.015535] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.015727] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.015677] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.015945] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.016019] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.016140] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [275.016308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.016293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.016526] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.016707] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.016926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [275.017206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [275.017517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [275.017786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.018040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.018280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [275.019135] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.019442] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.048032] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [275.048340] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [275.048721] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.048721] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.049014] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [275.049133] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.049277] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [275.049530] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.049603] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [275.049951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [275.050405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [275.050847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [275.051254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [275.051689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [275.052106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [275.053255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.053637] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.081423] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.081827] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [275.082124] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [275.082427] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [275.082555] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.082670] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.082904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.082989] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.083141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.083403] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.083384] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.083628] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.083848] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [275.084073] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [275.084343] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [275.084655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [275.085165] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.085613] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [275.085825] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [275.086033] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [275.086237] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.086553] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.086755] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.086950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.087143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.087327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [275.087579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [275.087783] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [275.088042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [275.088396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [275.088738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [275.089129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.089539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.089888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [275.091109] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.091433] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.097997] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.131327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.131655] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [275.131880] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [275.132071] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [275.132254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.132484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [275.132615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.132666] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [275.132889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [275.132959] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.133075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.133258] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.133245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.133477] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.133673] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.133886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [275.134256] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.134548] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [275.134719] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [275.134894] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [275.135067] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.135237] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [275.135488] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [275.135674] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [275.135864] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.136018] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.136199] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.136370] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.136529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [275.136787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [275.137047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [275.137307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [275.137609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [275.137865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [275.138857] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.139133] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.148014] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.181484] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [275.181734] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [275.181943] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [275.182142] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.182336] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.182595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [275.182726] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.182788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [275.182984] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [275.183075] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.183168] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.183366] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.183390] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.183545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.183795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [275.184313] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [275.184568] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [275.184748] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [275.184924] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.185095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.185266] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [275.186127] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [275.186326] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [275.186539] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.186710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.186911] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.187107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [275.187403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [275.187666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [275.187942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.188200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.188491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [275.189211] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.189517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.214674] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [275.214959] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [275.215202] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.215487] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.215626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.215714] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [275.215979] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [275.216038] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.216251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [275.216410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.216633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [275.216951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [275.217233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [275.217600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [275.217911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [275.218698] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.218952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.247919] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.248176] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [275.248443] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [275.248637] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [275.248589] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.248831] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.249019] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.248980] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.249219] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [275.249292] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.249469] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [275.249643] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.249804] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.249965] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [275.250121] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [275.250303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [275.250608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [275.250871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [275.251128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.251462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.251726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [275.252793] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.253057] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.264749] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.297894] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.298174] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [275.298437] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [275.298642] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [275.298577] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.298826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.298924] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.299008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.299184] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [275.299194] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.299427] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [275.299607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.299814] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.300014] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [275.300189] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [275.300413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [275.300695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [275.300954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [275.301208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [275.301482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [275.301780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [275.302783] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.303041] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.314761] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.347961] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691

<7> [275.348235] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360

<7> [275.348537] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0

<7> [275.348685] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.348761] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.348969] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.349060] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.349195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.349404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.349458] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.349666] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [275.349871] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.350078] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.350279] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.350570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [275.350911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [275.351201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [275.351519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.351823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.352140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [275.352904] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.353205] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.381242] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [275.381530] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [275.381652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.381729] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.381916] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [275.381991] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.382105] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [275.382299] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [275.382273] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.382566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [275.382846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [275.383105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [275.383375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [275.383627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [275.383934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [275.384613] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.384900] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.414607] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.414903] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [275.415114] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [275.415316] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [275.415591] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.415791] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.415724] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.416029] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.416122] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.416234] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.416464] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.416502] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.416648] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [275.416839] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [275.417034] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [275.417257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [275.417633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [275.418048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [275.418418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.418826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.419145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [275.420168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.420543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.431426] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.464538] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.464822] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [275.465031] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [275.465227] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [275.465474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.465667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [275.465600] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.465850] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [275.465941] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.466057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [275.466214] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.466254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.466464] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.466631] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.466794] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.466992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [275.467269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [275.467581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [275.467837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [275.468079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [275.468315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [275.469200] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.469518] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.481397] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.514598] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [275.514824] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [275.515032] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [275.515235] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.515484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.515612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.515677] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.515894] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.515954] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.516093] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [275.516222] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.516265] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.516480] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.516662] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.516874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [275.517296] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [275.517552] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [275.517735] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [275.517903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.518100] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.518290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.518497] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.518656] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [275.518816] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.518983] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.519146] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.519339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [275.519609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [275.519870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [275.520115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.520375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.520658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [275.521414] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.521679] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.548017] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [275.548306] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [275.548635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.548725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.548883] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [275.549111] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [275.549162] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.549442] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [275.549546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.549686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [275.550148] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [275.550419] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [275.550641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.550881] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [275.551079] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [275.551275] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [275.551536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [275.551850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [275.552117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [275.552371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [275.552616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [275.552860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [275.553636] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.553866] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.581090] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.581206] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [275.581272] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [275.581359] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [275.581368] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.581440] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.581518] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.581527] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.581595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.581670] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.581654] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.581737] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.581805] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [275.581873] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [275.581940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [275.582015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [275.582145] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.582223] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [275.582290] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [275.582381] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [275.582456] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.582524] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.582592] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.582659] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.582721] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.582777] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [275.582832] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [275.582886] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [275.582944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [275.583037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [275.583127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [275.583211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.583294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.583407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [275.583853] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.583952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.597782] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.631219] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.631548] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [275.631749] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [275.631939] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [275.632126] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.632398] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [275.632433] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.632619] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [275.632857] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [275.632838] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.633075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.633175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.633259] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.633504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.633688] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.633908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [275.634525] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.634779] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [275.634961] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [275.635136] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [275.635328] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.635504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [275.635682] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [275.635861] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [275.636042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.636232] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.636506] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.636695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.636879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [275.637166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [275.637519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [275.637794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [275.638106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [275.638460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [275.639595] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.639906] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.648125] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.681428] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [275.681663] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [275.681862] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [275.682048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.682229] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.682459] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [275.682586] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.682639] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [275.682859] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [275.682930] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.683054] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.683225] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.683253] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.683493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [275.683693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [275.683957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [275.684209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [275.684488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.684743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.685009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [275.685797] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.686093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.714565] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [275.714810] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [275.715023] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.715221] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.715479] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [275.715504] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.715672] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [275.715861] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.715895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [275.716178] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.716261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [275.716601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [275.716915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [275.717212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [275.717758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [275.718711] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.719020] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.747847] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.748168] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [275.748489] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [275.748627] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.748705] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [275.748901] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.748990] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.749090] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.749337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [275.749285] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.749526] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [275.749741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.749926] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.750118] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [275.750286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [275.750537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [275.750812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [275.751080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [275.751372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.751637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.751899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [275.752889] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.753165] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.764658] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.797785] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.798067] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [275.798349] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [275.798481] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.798551] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [275.798743] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.798829] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.798924] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.799102] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [275.799105] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.799325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [275.799526] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.799706] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.799883] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [275.800055] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [275.800255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [275.800606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [275.800869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [275.801120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [275.801385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [275.801681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [275.802672] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.802932] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.814590] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [275.847782] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [275.848051] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597

<7> [275.848246] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293

<7> [275.848503] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161

<7> [275.848689] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.848631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.848862] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.848970] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.849028] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.849190] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.849238] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.849381] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.849537] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.849721] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.849902] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.850060] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.850217] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [275.850434] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [275.850624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [275.850821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [275.851072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [275.851333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [275.851570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [275.851816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [275.852075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [275.853035] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.853292] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.864216] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:35:plane 1A]

<7> [275.864785] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [275.864954] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [275.881615] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [275.914454] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [275.914700] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [275.914885] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [275.915064] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [275.915239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.915473] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [275.915652] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [275.915612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.915865] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [275.915941] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.916091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [275.916215] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.916368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [275.916627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [275.916877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.917126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [275.917405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [275.918086] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.919041] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.964674] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [275.965031] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [275.965392] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [275.965466] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [275.965627] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [275.965847] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [275.965879] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [275.966074] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [275.966245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [275.966314] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.966552] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [275.966774] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [275.966987] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [275.967197] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [275.967445] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [275.967653] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [275.967847] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [275.968071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [275.968393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [275.968706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [275.969011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.969359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [275.969665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [275.970915] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [275.971252] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [275.980856] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [275.998548] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [275.998812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.031247] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.031519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.031666] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.031763] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [276.032010] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [276.032014] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.032210] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [276.032343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.032437] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [276.032625] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.032802] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [276.032975] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [276.033176] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [276.033407] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.033568] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.033733] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.033910] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.034133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [276.034469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [276.034737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [276.035021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [276.035332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [276.035609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [276.036686] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.036942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.048261] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.048518] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.081334] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.081434] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.081605] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [276.081809] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [276.081784] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.082005] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [276.082069] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.082194] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [276.082411] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.082599] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.082786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.083006] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.083198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [276.083404] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.083583] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.083759] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.083958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [276.084295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [276.084573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [276.084843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [276.085107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [276.085468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [276.086529] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.086807] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.087395] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [276.087629] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [276.097991] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.131113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.131452] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [276.131561] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.131728] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [276.131951] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [276.131944] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.132175] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.132272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.132450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [276.132693] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [276.132932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [276.133174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [276.133533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [276.133894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [276.134239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [276.134633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [276.134999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [276.135968] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.136345] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.181333] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.181734] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.182139] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [276.182453] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [276.182586] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.182694] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [276.182926] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [276.183027] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.183153] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.183417] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.183436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.183659] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.183872] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.184069] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.184258] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [276.184517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [276.184708] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [276.184942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [276.185259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [276.185625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [276.185934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [276.186241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [276.186596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [276.188041] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.188370] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.197463] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [276.214964] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.215230] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.247785] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.248035] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.248313] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [276.248429] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.248552] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [276.248746] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [276.248757] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.248933] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [276.249042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.249119] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.249325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [276.249520] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [276.249734] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [276.249908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.250080] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.250253] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.250479] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.250697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [276.250985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [276.251259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [276.251573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [276.251837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [276.252151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [276.253263] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.253586] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.264696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.264899] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.297887] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.298156] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [276.298405] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [276.298602] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [276.298540] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.298792] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [276.298886] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.298970] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.299145] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [276.299161] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.299351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [276.299525] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [276.299731] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [276.299926] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.300105] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.300298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.300500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [276.300819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [276.301099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [276.301397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [276.301722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [276.301981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [276.302927] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.303201] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.303880] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [276.304113] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [276.314627] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.347746] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.348015] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [276.348211] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [276.348469] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [276.348658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.348609] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.348850] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [276.348958] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.349040] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [276.349280] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [276.349251] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.349499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [276.349837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [276.350137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [276.350524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [276.350814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [276.351122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [276.352079] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.352418] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.397854] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.398203] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.398616] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [276.398714] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.398851] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [276.399052] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [276.399102] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.399247] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [276.399493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.399469] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.399683] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [276.399871] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [276.400078] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [276.400299] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.400494] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [276.400659] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [276.400826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [276.401033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [276.401327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [276.401613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [276.401981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [276.402344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [276.402653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [276.404191] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.404539] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.414123] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [276.431705] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.431966] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.464393] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.464625] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.464857] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [276.465083] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [276.465313] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [276.465492] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [276.465449] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.465685] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.465778] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.465858] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [276.466040] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [276.466065] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.466272] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [276.466455] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.466636] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [276.466818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [276.466994] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [276.467194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [276.467504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [276.467776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [276.468040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [276.468372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [276.468629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [276.469844] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.470118] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.481513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.481721] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.514506] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.514768] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597

<7> [276.514967] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293

<7> [276.515150] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161

<7> [276.515372] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [276.515550] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.515513] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.515726] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.515840] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.515899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.516092] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.516106] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.516274] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [276.516440] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.516606] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.516767] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.516957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [276.517294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [276.517559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [276.517812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [276.518062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [276.518323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [276.519185] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.519484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.520118] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [276.520373] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [276.531318] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.564365] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.564647] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [276.564876] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [276.565073] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [276.565302] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.565313] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.565495] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [276.565686] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [276.565662] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.565920] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [276.565959] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.566178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [276.566720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.566974] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [276.567219] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [276.567478] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [276.567685] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.567890] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [276.568107] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [276.568377] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [276.568584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [276.568900] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [276.569213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [276.569566] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [276.569922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [276.570227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [276.571087] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.571428] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.614515] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.614840] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.615160] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [276.615443] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [276.615574] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.615648] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [276.615876] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [276.615956] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.616067] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.616260] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.616276] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.616435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.616646] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.616828] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.616994] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [276.617159] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [276.617360] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [276.617558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [276.618055] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.618271] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.618471] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [276.618632] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [276.618791] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [276.618961] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [276.619138] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.619380] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.619555] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.619725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.619882] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.620035] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [276.620190] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [276.620399] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [276.620594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [276.620895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [276.621152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [276.621452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [276.621713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [276.621973] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [276.623097] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.623427] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.630753] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [276.648022] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.648237] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.681007] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.681224] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.681506] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [276.681615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.681730] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [276.681924] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [276.681950] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.682096] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [276.682221] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.682281] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.682449] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [276.682634] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [276.682800] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [276.682971] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.683141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.683347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.683523] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.683719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [276.684011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [276.684277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [276.684526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [276.684775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [276.685053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [276.686064] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.686361] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.697888] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.698075] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.730999] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.731309] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [276.731296] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.731526] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [276.731669] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.731733] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [276.731927] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [276.731976] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.732111] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.732317] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.732537] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.732729] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.732903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [276.733075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.733259] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.733427] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.733621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [276.733893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [276.734164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [276.734456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [276.734731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [276.734988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [276.736022] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.736304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.736866] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [276.737108] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [276.747874] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.781002] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.781303] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [276.781409] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.781514] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [276.781715] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [276.781757] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.781904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.782035] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.782083] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [276.782283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [276.782461] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [276.782672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [276.782938] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [276.783199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [276.783493] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [276.783748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [276.784007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [276.784804] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.785065] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.831129] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.831471] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.831777] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [276.831969] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [276.832144] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [276.832368] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [276.832540] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.832504] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.832710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.832851] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.832912] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.833084] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.833146] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.833273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.833442] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [276.833616] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [276.833796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [276.833981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [276.834265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [276.834519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [276.834766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [276.835023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [276.835292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [276.836675] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.836960] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.847362] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [276.864918] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.865204] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.897708] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.897966] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.898264] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [276.898477] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [276.898410] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.898679] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [276.898784] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.898881] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [276.899064] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.899081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.899273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [276.899497] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [276.899691] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [276.899903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.900085] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [276.900300] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [276.900475] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [276.900677] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [276.900947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [276.901217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [276.901527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [276.901805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [276.902060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [276.903206] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.903516] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.914640] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.914850] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [276.947780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.948050] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [276.948343] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [276.948368] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.948541] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [276.948734] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [276.948717] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.948917] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.949016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.949092] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [276.949292] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [276.949466] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [276.949673] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [276.949856] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.950027] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.950198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [276.950449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [276.950746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [276.951002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [276.951264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [276.951547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [276.951790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [276.952717] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [276.952968] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [276.953603] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [276.953845] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [276.964556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.997639] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.997902] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [276.998117] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [276.998358] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [276.998541] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [276.998482] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [276.998724] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [276.998818] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [276.998913] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [276.999125] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [276.999103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [276.999375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [276.999761] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [276.999984] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [277.000164] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [277.000381] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [277.000552] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.000720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.000931] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [277.001123] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [277.001343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [277.001615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [277.001866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [277.002113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [277.002393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [277.002658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [277.003393] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.003639] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.047751] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.048125] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.048470] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.048579] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.048757] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [277.048950] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [277.048927] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.049125] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [277.049196] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.049328] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [277.049495] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.049660] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.049825] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [277.050009] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [277.050177] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.050399] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.050567] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [277.050765] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [277.050959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [277.051244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [277.051516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [277.051780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [277.052077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [277.052358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [277.053487] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.053763] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.064019] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [277.081676] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.081940] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.114268] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.114487] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.114721] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [277.114918] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [277.115108] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [277.115339] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [277.115526] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.115480] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.115709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.115829] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.115931] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [277.116120] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [277.116116] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.116337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.116519] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.116699] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [277.116877] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [277.117123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [277.117669] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.117890] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.118105] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [277.118315] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [277.118486] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [277.118653] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [277.118852] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.119037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.119203] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [277.119431] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [277.119595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.119754] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.119911] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [277.120066] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [277.120249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [277.120495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [277.120744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [277.121010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [277.121261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [277.121549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [277.122638] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.122889] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.131351] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.131567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.164307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.164617] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823

<7> [277.164885] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614

<7> [277.165095] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614

<7> [277.165364] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [277.165481] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.165571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.165770] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [277.165856] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.165963] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [277.166151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.166186] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [277.166437] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.166643] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [277.166824] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [277.167000] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [277.167174] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.167393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [277.167561] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [277.167723] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [277.167885] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [277.168045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.168858] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.169024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.169228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [277.169507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [277.169784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [277.170053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [277.170376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [277.170641] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [277.171635] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.171913] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.172591] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [277.172836] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [277.181054] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.214248] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.214509] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [277.214706] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [277.214902] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [277.215095] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.215330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [277.215450] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.215523] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [277.215725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [277.215801] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.215934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [277.216094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.216234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [277.216513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [277.216788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [277.217114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [277.217463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [277.218143] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.218458] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.264292] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.264574] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.264840] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [277.265031] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [277.265238] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [277.265412] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [277.265365] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.265582] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.265695] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.265783] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [277.265985] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [277.265999] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.266158] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [277.266383] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.266551] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [277.266714] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [277.266871] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [277.267053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [277.267341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [277.267596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [277.267865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [277.268134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [277.268427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [277.269403] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.269664] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.280651] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [277.298299] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.298602] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.330926] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.331175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.331506] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [277.331611] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.331770] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [277.331966] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [277.331977] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.332152] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [277.332298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.332388] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.332571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [277.332752] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [277.332964] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [277.333166] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.333421] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [277.333595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [277.333774] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [277.333991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [277.334361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [277.334653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [277.334953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [277.335268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [277.335620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [277.336671] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.336953] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.347816] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.348023] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.380909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.381179] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823

<7> [277.381507] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614

<7> [277.381540] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.381709] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614

<7> [277.381909] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [277.381893] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.382112] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.382224] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.382355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [277.382577] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [277.382818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [277.383072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [277.383318] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.383527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.383729] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.383951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [277.384267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [277.384562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [277.384860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [277.385158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [277.385511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [277.386611] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.386897] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.387527] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [277.387773] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [277.397711] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.430909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.431259] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [277.431261] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.431563] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [277.431657] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.431799] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [277.432010] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.431983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.432239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [277.432445] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [277.432690] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [277.432934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [277.433259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [277.433532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [277.433795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [277.434054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [277.434340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [277.435069] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.435381] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.481093] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.481538] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.481656] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.482014] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.481992] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.482427] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [277.482452] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.482698] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [277.482956] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [277.483226] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [277.483528] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.483757] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [277.484003] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [277.484286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [277.484535] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.484741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [277.484966] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [277.485204] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [277.485476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [277.485847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [277.486215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [277.486594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [277.486929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [277.487422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [277.489067] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.489441] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.497261] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [277.515078] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.515477] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.547759] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.548074] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.548453] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [277.548549] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.548761] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [277.549018] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [277.548977] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.549305] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [277.549379] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.549594] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.549822] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [277.550042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [277.550294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [277.550530] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.550762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [277.550953] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [277.551213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [277.551482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [277.551795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [277.552110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [277.552462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [277.552794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [277.553073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [277.554305] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.554580] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.564720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.564934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.597839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.598273] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826

<7> [277.598264] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.598638] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605

<7> [277.598778] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.598922] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620

<7> [277.599205] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [277.599220] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.599461] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.599716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.599968] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [277.600286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [277.600538] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [277.600788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.601048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.601315] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.601611] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [277.602199] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.602480] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826

<7> [277.602699] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605

<7> [277.602911] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620

<7> [277.603122] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [277.603394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.603601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.603808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [277.604035] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [277.604309] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [277.604539] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.604775] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.605055] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.605325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [277.605731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [277.606092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [277.606450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [277.606823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [277.607215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [277.608420] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.608716] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.609414] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [277.609646] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [277.614477] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.647471] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.647735] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [277.647942] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289

<7> [277.648141] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164

<7> [277.648406] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.648601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.648553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.648796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [277.648901] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.649008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [277.649205] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.649224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [277.649487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [277.649747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [277.650019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [277.650324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [277.650629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [277.651334] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.651593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.697625] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.697934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.698319] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913

<7> [277.698371] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.698541] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452

<7> [277.698745] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794

<7> [277.698747] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.698929] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892

<7> [277.699032] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.699111] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.699330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.699509] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [277.699718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [277.699917] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.700085] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.700290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [277.700455] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [277.700657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [277.700930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [277.701215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [277.701540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [277.701803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [277.702069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [277.703456] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.703730] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.713920] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [277.731397] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.731646] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.764203] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.764329] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.764434] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.764679] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691

<7> [277.764677] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.764921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676

<7> [277.764965] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.765121] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350

<7> [277.765357] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334

<7> [277.765542] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.765724] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.765905] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [277.766127] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [277.766375] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.766556] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [277.766753] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [277.766970] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [277.767210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [277.767490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [277.767760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [277.768025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [277.768305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [277.768558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [277.769707] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.769975] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.781245] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.781480] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.814187] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.814456] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 691) -> ( 0 - 823), size 691 -> 823

<7> [277.814658] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 691 - 1367) -> ( 823 - 2437), size 676 -> 1614

<7> [277.814853] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2717) -> (2437 - 4051), size 1350 -> 1614

<7> [277.815042] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0

<7> [277.815278] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.815391] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.815465] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [277.815650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [277.815742] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.815871] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [277.816074] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [277.816037] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.816285] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.816464] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.816640] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [277.816847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [277.817120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [277.817420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [277.817742] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [277.818007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [277.818299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [277.819257] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.819528] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.820236] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [277.820468] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [277.831088] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.864251] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.864560] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [277.864818] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [277.865019] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [277.865251] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.865438] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [277.865375] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.865640] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [277.865729] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.865846] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [277.866024] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.866042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [277.866347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [277.866615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [277.866881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [277.867141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [277.867450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [277.868218] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.868484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.914339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.914683] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.915058] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [277.915382] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [277.915512] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.915625] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [277.915859] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [277.915971] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.916100] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.916420] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [277.916435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.916685] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [277.916928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [277.917136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.917413] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [277.917620] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [277.917823] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [277.918067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [277.918436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [277.918842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [277.919236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [277.919601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [277.919963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [277.921373] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.921750] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.930545] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [277.948028] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.948354] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.980954] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.981260] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [277.981393] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [277.981551] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [277.981836] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [277.981793] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [277.982043] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [277.982110] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [277.982288] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [277.982493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.982709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [277.982894] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [277.983077] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [277.983305] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [277.983518] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [277.983701] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [277.983892] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [277.984112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [277.984454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [277.984748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [277.985037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [277.985375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [277.985733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [277.986854] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [277.987177] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [277.997928] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [277.998178] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [278.030945] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.031235] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823

<7> [278.031340] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.031440] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614

<7> [278.031634] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614

<7> [278.031691] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.031823] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [278.031996] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.031983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.032195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.032368] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.032570] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.032751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [278.032919] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.033093] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.033355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.033554] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [278.033835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [278.034095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [278.034375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [278.034672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [278.034928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [278.035995] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.036284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.036863] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [278.037103] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [278.047661] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.080780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.081063] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [278.081332] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [278.081535] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [278.081480] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.081722] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.081823] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.081901] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [278.082077] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [278.082092] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.082320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [278.082520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [278.082970] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.083207] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [278.083415] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [278.083590] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [278.083763] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.083926] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [278.084090] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [278.084289] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [278.084462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [278.084747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [278.085001] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [278.085275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [278.085567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [278.085811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [278.086519] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.086772] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.130923] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.131339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [278.131448] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.131663] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [278.131912] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [278.131851] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.132176] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [278.132252] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.132409] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [278.132635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.132906] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.133136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.133447] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.133659] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.133865] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [278.134072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [278.134331] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [278.134624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [278.135232] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.135495] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [278.135813] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [278.136036] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [278.136286] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [278.136492] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [278.136698] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.136943] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.137188] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.137389] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.137585] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.137777] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [278.137998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [278.138196] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [278.138386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [278.138689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [278.138984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [278.139296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [278.139621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [278.139914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [278.141449] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.141740] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.147193] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [278.164639] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.164873] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [278.197409] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.197642] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [278.197882] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [278.198101] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [278.198347] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [278.198526] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [278.198492] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.198706] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.198889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [278.198842] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.199070] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [278.199125] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.199306] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [278.199487] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.199662] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.199831] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.200001] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.200217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [278.200479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [278.200736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [278.201002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [278.201289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [278.201584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [278.202661] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.202924] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.214421] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.214620] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [278.247569] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.247817] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826

<7> [278.248022] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605

<7> [278.248268] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620

<7> [278.248461] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [278.248410] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.248649] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.248762] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.248833] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.249028] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [278.249070] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.249313] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [278.249507] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [278.249722] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.249900] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.250078] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.250340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [278.250663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [278.250941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [278.251213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [278.251477] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [278.251732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [278.252718] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.252981] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.253632] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [278.253856] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [278.264317] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.297383] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.297648] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [278.297849] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289

<7> [278.298051] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164

<7> [278.298303] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.298499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.298434] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.298707] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [278.298788] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.298925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [278.299067] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.299158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [278.299425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [278.299689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [278.299965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [278.300273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [278.300547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [278.301307] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.301587] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.347512] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.347837] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [278.348211] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913

<7> [278.348297] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.348434] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452

<7> [278.348635] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794

<7> [278.348674] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.348820] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892

<7> [278.349001] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.348964] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.349213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.349392] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [278.349604] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [278.349795] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.349981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.350155] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [278.350309] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [278.350498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [278.350752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [278.351016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [278.351316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [278.351632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [278.351879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [278.353181] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.353460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.363811] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [278.381316] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.381599] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [278.414092] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.414413] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [278.414701] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691

<7> [278.414946] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676

<7> [278.415190] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350

<7> [278.415397] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334

<7> [278.415330] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.415600] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.415703] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.415805] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.415992] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [278.415994] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.416208] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [278.416391] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.416575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.416759] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [278.416939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [278.417158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [278.417428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [278.417700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [278.417962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [278.418308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [278.418580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [278.419665] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.419937] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.431089] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [278.431347] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [278.464267] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 691) -> ( 0 - 2018), size 691 -> 2018

<7> [278.464478] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 691 - 1367) -> (2018 - 4051), size 676 -> 2033

<7> [278.464666] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2717) -> ( 0 - 0), size 1350 -> 0

<7> [278.464848] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0

<7> [278.465037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.465281] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.465471] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [278.465416] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.465698] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [278.465771] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.465889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.466070] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.466064] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.466298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.466495] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.466718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [278.466930] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.467113] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.467343] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.467522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [278.467697] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.467868] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.468038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.468275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [278.468549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [278.468818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [278.469072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [278.469369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [278.469644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [278.470499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.470768] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.471387] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [278.471605] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:35:plane 1A]

<7> [278.497477] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [278.497729] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [278.497928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.498114] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [278.498366] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [278.498485] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.498545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [278.498776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [278.498822] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.499168] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [278.499113] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.499351] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [278.499531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.499703] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [278.499892] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [278.500062] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [278.500285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [278.500558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [278.500827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [278.501092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [278.501374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [278.501600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [278.502246] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.502472] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.530916] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.531418] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [278.531393] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.531720] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [278.531791] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.531948] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [278.532203] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.532262] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.532481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.532695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.532950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.533218] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.533420] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [278.533615] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [278.533812] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [278.534034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [278.534519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.534783] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [278.535027] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [278.535281] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [278.535483] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.535720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.535943] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.536185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.536371] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.536552] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [278.536734] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [278.536910] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [278.537086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [278.537421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [278.537760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [278.538062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [278.538373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [278.538705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [278.539632] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.539925] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.547421] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.580689] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.580985] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [278.581283] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [278.581410] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.581501] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [278.581708] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.581785] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.581913] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [278.582128] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [278.582090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.582328] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [278.582568] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.582770] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.582980] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.583239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.583463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [278.583940] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.584184] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [278.584399] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [278.584574] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [278.584741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.584899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [278.585056] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [278.585291] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [278.585462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.585613] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.585771] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.585931] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.586102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [278.586416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [278.586682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [278.586948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [278.587240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [278.587525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [278.588455] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.588721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.597460] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.630822] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2018), size 1606 -> 2018

<7> [278.631175] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1606 - 2432) -> (2018 - 4051), size 826 -> 2033

<7> [278.631298] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.631440] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0

<7> [278.631688] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.631738] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.631937] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.632235] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.632180] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.632517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.632763] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [278.632989] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.633275] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.633505] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.633771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [278.634138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [278.634490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [278.634839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [278.635229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [278.635565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [278.636596] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.636944] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.664131] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [278.664432] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [278.664678] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.664898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [278.665136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [278.665281] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.665395] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [278.665623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [278.665658] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.665940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [278.665993] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.666294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [278.666606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [278.666891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [278.667183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [278.668142] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.668466] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.697383] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.697655] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [278.697849] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [278.698037] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [278.698283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.698476] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.698435] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.698674] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.698862] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.698807] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.699024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.699095] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.699227] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [278.699424] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [278.699585] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [278.699772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [278.700060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [278.700366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [278.700630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [278.700886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [278.701141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [278.702167] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.702454] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.714352] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.747402] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.747742] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [278.748038] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [278.748348] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [278.748486] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.748573] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.748796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [278.748895] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.749037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [278.749274] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.749349] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [278.749581] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.749801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.750007] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.750251] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.750517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [278.750865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [278.751207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [278.751529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [278.751838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [278.752145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [278.753404] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.753732] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.764423] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.797537] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2026), size 1606 -> 2026

<7> [278.797774] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1606 - 2432) -> (2026 - 4051), size 826 -> 2025

<7> [278.797978] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0

<7> [278.798232] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.798432] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.798370] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.798629] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [278.798723] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.798863] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [278.799006] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.799082] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [278.799349] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.799537] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.799717] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.799923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [278.800219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [278.800509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [278.800793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [278.801058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [278.801349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [278.802176] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.802467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.830767] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [278.831065] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [278.831404] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.831537] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.831635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.831857] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [278.831933] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.832117] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [278.832293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.832358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [278.832655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [278.832950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [278.833284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [278.833573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [278.833866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [278.834896] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.835228] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.864053] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.864416] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2310), size 1354 -> 2310

<7> [278.864636] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1354 - 4051) -> (2310 - 2894), size 2697 -> 584

<7> [278.864844] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2894 - 4051), size 0 -> 1157

<7> [278.865048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.865317] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.865458] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.865562] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [278.865763] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [278.865865] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.865947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.866143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.866205] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.866320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [278.866492] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [278.866685] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [278.866955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [278.867257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [278.867526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [278.867838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [278.868138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [278.869353] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.869657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.880949] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.914056] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.914457] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618

<7> [278.914739] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817

<7> [278.914993] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616

<7> [278.915379] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.915428] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.915624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.915871] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [278.915863] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.916122] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [278.916277] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.916351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.916574] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.916792] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [278.917040] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [278.917342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [278.917831] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.918144] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618

<7> [278.918421] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817

<7> [278.918648] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616

<7> [278.918850] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.919045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.919302] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [278.919504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [278.919702] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.919903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [278.920136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [278.920343] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [278.920561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [278.920882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [278.921207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [278.921556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [278.921861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [278.922153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [278.923257] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.923551] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.930909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [278.964215] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2018), size 1618 -> 2018

<7> [278.964545] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1618 - 2435) -> (2018 - 4051), size 817 -> 2033

<7> [278.964828] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0

<7> [278.965180] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.965288] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.965503] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.965760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.965762] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.966031] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.966225] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.966358] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [278.966628] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.966876] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.967144] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.967489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [278.968050] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2018), size 1618 -> 2018

<7> [278.968379] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1618 - 2435) -> (2018 - 4051), size 817 -> 2033

<7> [278.968632] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0

<7> [278.968885] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.969201] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [278.969457] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [278.969733] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [278.969971] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [278.970246] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.970490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.970732] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [278.971033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [278.971454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [278.971853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [278.972195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [278.972526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [278.972892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [278.973763] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [278.974054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [278.997431] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [278.997727] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [278.997981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [278.998294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [278.998532] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [278.998451] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [278.998812] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [278.998902] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [278.999070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [278.999306] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [278.999613] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [278.999853] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [279.000063] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.000321] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [279.000517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [279.000712] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [279.000917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [279.001347] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [279.001539] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [279.001700] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.001855] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [279.002004] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [279.002185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [279.002345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [279.002588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [279.002833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [279.003064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.003318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.003558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [279.004226] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.004436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.030701] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.031148] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [279.031266] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.031435] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [279.031690] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [279.031705] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.031941] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.032141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.032245] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.032527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.032805] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.033047] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.033352] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [279.033575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [279.033786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [279.034037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [279.034658] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.034914] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [279.035129] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [279.035345] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [279.035547] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.035725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.035904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.036079] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.036306] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.036484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [279.036635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [279.036782] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [279.036939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [279.037223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [279.037461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [279.037698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [279.037987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [279.038230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [279.038985] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.039613] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.047425] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.080711] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.081050] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [279.081385] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [279.081514] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.081624] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [279.081853] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.081928] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.082075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [279.082306] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.082367] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [279.082595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [279.082807] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.083013] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.083272] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.083503] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.083734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [279.084060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [279.084438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [279.084763] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.085092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.085411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [279.086431] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.086761] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.097643] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.130678] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2018), size 1606 -> 2018

<7> [279.130979] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1606 - 2432) -> (2018 - 4051), size 826 -> 2033

<7> [279.131309] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0

<7> [279.131441] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.131567] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.131802] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.131866] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.132024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.132253] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.132321] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.132534] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [279.132748] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.132962] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.133220] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.133466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [279.133818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [279.134147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [279.134526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [279.134836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [279.135171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [279.136153] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.136489] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.164167] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [279.164241] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.164539] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [279.164716] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.164827] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.165116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [279.165144] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.165362] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [279.165655] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [279.165929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [279.166324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [279.166668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [279.166979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.167313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.167683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [279.168662] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.168990] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.197338] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.197659] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [279.197891] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [279.198133] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [279.198256] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.198332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.198522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.198606] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.198711] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.198908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.198900] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.199102] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.199280] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [279.199456] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [279.199667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [279.199857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [279.200128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [279.200384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [279.200661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [279.200930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [279.201231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [279.202331] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.202619] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.214320] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.247333] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.247633] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [279.247850] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [279.248065] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [279.248355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.248485] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.248561] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [279.248765] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [279.248862] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.248992] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [279.249226] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.249229] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.249419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.249612] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.249831] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.250041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [279.250373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [279.250656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [279.250903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.251175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.251476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [279.252588] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.252862] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.264290] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.297464] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2026), size 1606 -> 2026

<7> [279.297699] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1606 - 2432) -> (2026 - 4051), size 826 -> 2025

<7> [279.297896] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0

<7> [279.298133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.298330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.298263] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.298523] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.298617] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.298731] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.298907] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [279.298898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.299097] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.299271] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.299441] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.299637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [279.299911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [279.300222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [279.300555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [279.300832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [279.301118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [279.301904] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.302204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.330636] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [279.330905] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [279.331235] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.331329] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.331435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.331643] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [279.331683] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.331868] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [279.331985] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.332125] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [279.332414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [279.332696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [279.332967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.333268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.333584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [279.334490] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.334779] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.364028] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.364437] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2310), size 1354 -> 2310

<7> [279.364534] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.364679] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1354 - 4051) -> (2310 - 2894), size 2697 -> 584

<7> [279.364911] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2894 - 4051), size 0 -> 1157

<7> [279.364977] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.365177] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.365397] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.365402] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.365621] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [279.365885] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [279.366162] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.366393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.366607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [279.366810] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [279.367047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [279.367584] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.367845] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2310), size 1354 -> 2310

<7> [279.368138] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1354 - 4051) -> (2310 - 2894), size 2697 -> 584

<7> [279.368382] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2894 - 4051), size 0 -> 1157

<7> [279.368615] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.368819] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.369023] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [279.369299] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [279.369536] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.369727] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.369909] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [279.370112] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [279.370341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [279.370674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [279.371020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [279.371452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [279.371778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [279.372092] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [279.373263] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.373549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.380753] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.414032] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.414437] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618

<7> [279.414520] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.414685] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817

<7> [279.414906] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616

<7> [279.414916] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.415152] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.415282] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.415357] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.415564] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.415760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.415939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.416151] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.416330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.416505] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.416711] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [279.417186] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.417468] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618

<7> [279.417687] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817

<7> [279.417897] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616

<7> [279.418138] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.418349] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.418569] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.418768] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.418951] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.419157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.419355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.419524] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.419709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [279.419999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [279.420319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [279.420618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.420884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.421191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [279.422350] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.422655] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.430729] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.464026] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2687), size 1618 -> 2687

<7> [279.464451] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1618 - 2435) -> (2687 - 4051), size 817 -> 1364

<7> [279.464578] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.464744] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0

<7> [279.465024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.465103] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.465497] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.465559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.465852] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [279.466222] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [279.466461] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.466698] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.466946] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.467239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.467482] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [279.467720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.468001] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.468309] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.468602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [279.469247] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2687), size 1618 -> 2687

<7> [279.469488] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1618 - 2435) -> (2687 - 4051), size 817 -> 1364

<7> [279.469703] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0

<7> [279.469982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.470282] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.470556] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [279.470784] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [279.471050] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.471325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.471571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.471764] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.471961] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [279.472195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.472380] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.472562] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.472756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [279.473067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [279.473354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [279.473634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.473933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.474224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [279.475070] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.475318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.514009] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [279.514371] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [279.514613] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.514842] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [279.515122] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [279.515277] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.515380] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [279.515674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [279.515716] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.516018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [279.516093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.516378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [279.516744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.517068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.517429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [279.518314] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.518637] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.547663] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:493]

<7> [279.548226] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.548641] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.548954] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.567136] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.567480] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907

<7> [279.567734] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392

<7> [279.567937] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752

<7> [279.568546] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.568786] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.568993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.569243] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.569438] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.569624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [279.569800] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [279.569967] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [279.570197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [279.570462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [279.570722] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [279.570982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [279.571273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [279.571591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [279.572516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.572770] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.580935] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.613934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.614371] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [279.614423] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.614668] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [279.614916] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [279.614865] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.615206] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.615272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.615444] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [279.615681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [279.615942] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [279.616213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.616433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.616654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.616878] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.617201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [279.617553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [279.617900] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [279.618285] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [279.618662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [279.618992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [279.620080] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.620412] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.630808] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.663901] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687

<7> [279.664197] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364

<7> [279.664329] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.664412] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [279.664617] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.664688] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.664815] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.664967] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.664997] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.665262] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.665448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [279.665656] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.665839] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.666088] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.666331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [279.666634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [279.666934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [279.667260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.667595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.667879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [279.668699] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.668989] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.697313] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [279.697591] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [279.697814] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.698010] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [279.698269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [279.698470] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [279.698405] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.698679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [279.698757] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.698959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [279.699073] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.699259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [279.699529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.699795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.700134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [279.700993] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.701312] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.730506] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.730761] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907

<7> [279.730978] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392

<7> [279.731231] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752

<7> [279.731411] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.731389] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.731585] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.731751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.731744] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.731950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.732080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.732172] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.732364] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [279.732535] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [279.732693] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [279.732876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [279.733168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [279.733437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [279.733699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [279.733959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [279.734251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [279.735267] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.735546] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.747434] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.780588] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.780892] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [279.781178] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [279.781386] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [279.781344] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.781589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.781787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [279.781750] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.781977] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [279.782103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.782273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [279.782460] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.782641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.782821] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.782990] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.783253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [279.783599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [279.783898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [279.784221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [279.784495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [279.784767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [279.785857] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.786175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.797513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.830781] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697

<7> [279.831083] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354

<7> [279.831215] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.831312] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [279.831529] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.831594] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.831736] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.831901] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.831934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.832185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.832371] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [279.832557] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.832738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.832936] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.833170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [279.833551] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697

<7> [279.833731] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354

<7> [279.833903] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [279.834098] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.834272] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.834464] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.834671] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.834845] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [279.835017] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.835256] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.835468] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.835653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [279.835927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [279.836210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [279.836499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.836749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [279.837011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [279.837837] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.838133] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.863989] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [279.864335] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [279.864452] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.864565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.864775] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.864828] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.864977] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [279.865191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.865276] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [279.865537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [279.865999] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [279.866257] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [279.866447] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.866666] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.866867] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [279.867084] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [279.867333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [279.867632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [279.867916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [279.868226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.868511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [279.868766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [279.869546] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.869801] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.897334] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.897673] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936

<7> [279.897905] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376

<7> [279.898182] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739

<7> [279.898390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.898333] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.898591] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.898713] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.898788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [279.898993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [279.899063] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.899240] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.899428] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.899621] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [279.899795] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [279.899993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [279.900458] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.900674] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936

<7> [279.900846] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376

<7> [279.901009] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739

<7> [279.901223] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.901380] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.901542] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [279.901712] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [279.901872] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.902050] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.902216] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [279.902381] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [279.902552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [279.902821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [279.903128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [279.903466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [279.903748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [279.904053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [279.905134] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.905416] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.913941] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.947191] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.947500] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2936) -> ( 0 - 2306), size 2936 -> 2306

<7> [279.947778] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2936 - 3312) -> (2306 - 2893), size 376 -> 587

<7> [279.947979] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3312 - 4051) -> (2893 - 4051), size 739 -> 1158

<7> [279.948239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.948359] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.948434] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.948623] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.948712] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.948819] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.948989] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.948992] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.949204] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.949375] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.949543] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.949741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [279.950239] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.950477] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2936) -> ( 0 - 2306), size 2936 -> 2306

<7> [279.950698] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2936 - 3312) -> (2306 - 2893), size 376 -> 587

<7> [279.950887] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3312 - 4051) -> (2893 - 4051), size 739 -> 1158

<7> [279.951121] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.951359] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.951578] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.951763] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.951935] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.952134] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [279.952311] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [279.952481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [279.952664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [279.952928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [279.953226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [279.953525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [279.953796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [279.954101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [279.955174] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [279.955443] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [279.964000] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [279.997216] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2306) -> ( 0 - 2687), size 2306 -> 2687

<7> [279.997480] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2306 - 2893) -> (2687 - 4051), size 587 -> 1364

<7> [279.997704] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2893 - 4051) -> ( 0 - 0), size 1158 -> 0

<7> [279.997906] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [279.998146] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [279.998284] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [279.998340] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [279.998570] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [279.998639] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [279.998777] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [279.998947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.998922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [279.999149] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.999316] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [279.999547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [279.999830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [280.000133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [280.000408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [280.000681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [280.000941] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [280.001654] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.001925] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.030564] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [280.030827] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [280.031088] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.031289] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.031228] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.031482] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.031587] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.031709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.031880] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.031951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [280.032296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [280.032579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [280.032842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [280.033131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [280.033386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [280.034133] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.034416] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.063812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.064108] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907

<7> [280.064206] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.064320] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392

<7> [280.064498] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752

<7> [280.064559] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.064671] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.064841] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.064849] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.065052] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.065255] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.065426] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.065584] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [280.065744] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [280.065904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [280.066121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [280.066389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [280.066666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [280.066931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.067222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.067518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [280.068345] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.068625] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.080560] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.114084] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.114162] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.114429] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [280.114536] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.114656] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [280.114861] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [280.114850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.115098] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.115290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.115527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.115725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.115899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.116091] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.116257] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.116419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.116615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [280.116882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [280.117159] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [280.117409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [280.117655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [280.117922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [280.118972] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.119316] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.130718] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.163878] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687

<7> [280.164239] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364

<7> [280.164373] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.164498] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [280.164742] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.164810] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.164981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.165283] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.165260] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.165541] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.165787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [280.166024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.166247] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.166462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.166718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [280.167080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [280.167480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [280.167822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [280.168203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [280.168597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [280.169541] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.169892] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.197219] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [280.197501] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [280.197729] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.197943] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.198226] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.198343] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.198430] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.198665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [280.198715] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.198968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [280.199056] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.199307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [280.199598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [280.199936] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [280.200377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [280.201428] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.201730] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.230516] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.230883] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907

<7> [280.231285] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392

<7> [280.231389] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.231547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752

<7> [280.231767] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.231795] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.231978] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.232186] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.232248] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.232479] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.232687] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.232889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [280.233124] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [280.233320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [280.233545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [280.233870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [280.234221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [280.234538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.234853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.235184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [280.236397] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.236722] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.247463] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.280507] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.280882] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [280.281224] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [280.281363] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.281480] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [280.281724] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.281801] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.282021] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.282194] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.282269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.282497] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.282712] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.282925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.283190] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.283426] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.283661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [280.284132] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.284398] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [280.284611] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [280.284816] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [280.285045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.285241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.285435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.285629] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.285818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.286045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.286238] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.286423] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.286621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [280.286953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [280.287880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [280.288232] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [280.288535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [280.288873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [280.289983] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.290313] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.297387] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.330823] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697

<7> [280.331165] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354

<7> [280.331288] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.331411] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [280.331642] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.331692] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.331872] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.332116] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.332176] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [280.332410] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [280.332649] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [280.332867] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.333144] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.333352] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.333588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [280.334135] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697

<7> [280.334362] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354

<7> [280.334570] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [280.334798] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.335033] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.335242] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [280.335440] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [280.335634] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [280.335826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.336070] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.336264] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.336460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [280.336780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [280.337108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [280.337431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [280.337734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [280.338073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [280.338956] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.339291] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.363833] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [280.364176] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [280.364222] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.364414] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.364640] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.364654] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.364860] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [280.364992] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.365137] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [280.365386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [280.365869] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [280.366141] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [280.366337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.366533] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.366718] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [280.366943] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [280.367195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [280.367608] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [280.367774] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [280.367933] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.368169] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.368335] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [280.368474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [280.368634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [280.368867] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [280.369122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [280.369370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [280.369585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [280.369824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [280.370476] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.370674] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.397223] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.397621] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936

<7> [280.397908] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376

<7> [280.398275] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739

<7> [280.398412] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.398548] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.398808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.398887] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.399151] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [280.399343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.399425] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [280.399673] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.399912] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.400219] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [280.400481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [280.400756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [280.401425] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.401703] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936

<7> [280.401921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376

<7> [280.402170] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739

<7> [280.402362] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.402550] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.402744] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [280.402939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [280.403170] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.403367] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.403545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [280.403720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [280.403939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [280.404275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [280.404532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [280.404796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.405081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.405302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [280.406228] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.406458] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.413814] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.447133] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.447469] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2936) -> ( 0 - 2306), size 2936 -> 2306

<7> [280.447742] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2936 - 3312) -> (2306 - 2893), size 376 -> 587

<7> [280.447958] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3312 - 4051) -> (2893 - 4051), size 739 -> 1158

<7> [280.448234] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.448440] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.448373] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.448661] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [280.448751] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.448868] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [280.449092] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.449100] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.449285] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.449477] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [280.449667] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [280.449874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [280.450192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [280.450511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [280.450786] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [280.451061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [280.451315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [280.452392] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.452674] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.464154] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [280.497183] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.497580] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2306) -> ( 0 - 583), size 2306 -> 583

<7> [280.497896] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2306 - 2893) -> ( 583 - 2898), size 587 -> 2315

<7> [280.498240] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2893 - 4051) -> (2898 - 4051), size 1158 -> 1153

<7> [280.498376] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.498490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.498731] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.498814] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.498967] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [280.499282] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [280.499248] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.499514] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.499776] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.500028] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.500252] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.500471] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.500688] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.500932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 4, 8, 8, 8, 8, 8, 0, 0, 19, 4, 19

<7> [280.501433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [280.501701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [280.502128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [280.502465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [280.502798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [280.503203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [280.503533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [280.504744] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.505097] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.513465] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:35:plane 1A]

<7> [280.514075] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [280.514236] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [280.530966] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.563798] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.564127] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [280.564169] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.564339] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939

<7> [280.564540] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737

<7> [280.564548] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.564737] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.564855] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.564923] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.565158] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.565339] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.565585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [280.565866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [280.566146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [280.566401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.566650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.566912] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [280.567723] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.568040] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.613887] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.614332] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [280.614715] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673

<7> [280.615027] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692

<7> [280.615168] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.615292] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333

<7> [280.615573] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353

<7> [280.615649] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.615826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.616078] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.616116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.616397] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.616636] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.616868] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.617143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [280.617371] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [280.617596] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [280.617916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [280.618338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [280.618682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [280.619031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [280.619423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [280.619816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [280.621232] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.621582] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.630089] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [280.647644] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.647943] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [280.680528] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.680943] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [280.681483] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.681518] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452

<7> [280.681919] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913

<7> [280.682005] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.682316] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893

<7> [280.682423] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.682619] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793

<7> [280.682917] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.683290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.683616] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.683904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.684265] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.684552] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.684842] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.685194] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.685570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [280.686014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [280.686436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [280.686847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [280.687297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [280.687707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [280.689295] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.689705] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.697383] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.697574] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [280.730418] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.730745] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 452) -> ( 0 - 583), size 452 -> 583

<7> [280.731024] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 452 - 1365) -> ( 583 - 2898), size 913 -> 2315

<7> [280.731254] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2258) -> (2898 - 4051), size 893 -> 1153

<7> [280.731175] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.731485] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0

<7> [280.731582] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.731697] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.731907] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.731920] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.732172] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.732382] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.732636] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [280.732839] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.733075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.733275] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.733556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [280.733891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [280.734249] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [280.734610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [280.734907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [280.735282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [280.736558] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.736886] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.737625] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [280.737914] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [280.747296] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.780461] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.780822] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [280.781209] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939

<7> [280.781343] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.781465] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737

<7> [280.781715] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.781781] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.781947] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.782171] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.782224] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.782493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.782775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [280.783272] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.783536] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [280.783778] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939

<7> [280.784007] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737

<7> [280.784217] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.784423] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.784652] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.784859] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.785123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [280.785438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [280.785761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [280.786102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.786458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.786768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [280.787745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.788112] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.830504] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.830945] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.831307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [280.831436] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.831617] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673

<7> [280.831865] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692

<7> [280.831846] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.832162] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333

<7> [280.832265] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.832396] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353

<7> [280.832624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.832848] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.833155] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.833419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.833656] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.833873] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [280.834141] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [280.834353] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [280.834597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [280.834947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [280.835344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [280.835693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [280.836039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [280.836420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [280.837812] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.838223] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.846735] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [280.864514] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.864824] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [280.897049] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.897314] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [280.897569] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452

<7> [280.897813] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913

<7> [280.898062] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893

<7> [280.898257] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793

<7> [280.898191] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.898448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.898546] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.898648] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.898830] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.898836] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.899040] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.899217] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.899394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.899580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.899747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.899948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [280.900513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.900720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [280.900935] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452

<7> [280.901156] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913

<7> [280.901363] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893

<7> [280.901554] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793

<7> [280.901725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.901927] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [280.902158] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [280.902324] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [280.902495] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.902657] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [280.902822] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [280.903000] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [280.903172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [280.903434] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [280.903697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [280.903995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [280.904316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [280.904589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [280.905742] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.906049] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.914000] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.914200] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [280.947222] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.947530] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 452) -> ( 0 - 585), size 452 -> 585

<7> [280.947770] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 452 - 1365) -> ( 585 - 2894), size 913 -> 2309

<7> [280.948009] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2258) -> (2894 - 4051), size 893 -> 1157

<7> [280.948203] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0

<7> [280.948114] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.948393] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.948490] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.948579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.948765] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [280.948783] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.949013] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [280.949223] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [280.949431] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.949607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.949781] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [280.950044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [280.950336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [280.950618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [280.950891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [280.951190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [280.951456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [280.952509] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [280.952792] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [280.953483] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [280.953749] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [280.963975] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.997013] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [280.997302] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [280.997528] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 585 - 2894) -> ( 376 - 3312), size 2309 -> 2936

<7> [280.997727] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (3312 - 4051), size 1157 -> 739

<7> [280.997910] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [280.998157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [280.998337] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [280.998302] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [280.998536] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [280.998636] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [280.998737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [280.998918] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [280.999032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [280.999314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [280.999599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [280.999868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [281.000167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [281.001069] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.001359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.047177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.047541] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.047876] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 376) -> ( 0 - 679), size 376 -> 679

<7> [281.048187] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 376 - 3312) -> ( 679 - 1358), size 2936 -> 679

<7> [281.048317] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.048410] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3312 - 4051) -> (1358 - 2705), size 739 -> 1347

<7> [281.048622] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2705 - 4051), size 0 -> 1346

<7> [281.048724] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.048884] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.049170] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.049141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.049390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [281.049603] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [281.049813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.050042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.050233] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [281.050420] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [281.050684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [281.051006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [281.051299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [281.051594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [281.051930] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [281.052242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [281.053570] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.053887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.063374] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [281.081152] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.081481] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.113680] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.113990] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.114128] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.114283] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 679) -> ( 0 - 456), size 679 -> 456

<7> [281.114522] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 679 - 1358) -> ( 456 - 1360), size 679 -> 904

<7> [281.114531] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.114739] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1358 - 2705) -> (1360 - 2259), size 1347 -> 899

<7> [281.114860] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.114974] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2705 - 4051) -> (2259 - 4051), size 1346 -> 1792

<7> [281.115170] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.115363] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.115573] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [281.115788] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [281.116001] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.116175] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.116347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [281.116527] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [281.116752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [281.117042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [281.117318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [281.117588] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [281.117853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [281.118198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [281.119389] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.119673] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.130683] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.130889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.163674] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.164023] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 456) -> ( 0 - 583), size 456 -> 583

<7> [281.164082] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.164319] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 456 - 1360) -> ( 583 - 2898), size 904 -> 2315

<7> [281.164488] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.164541] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1360 - 2259) -> (2898 - 4051), size 899 -> 1153

<7> [281.164759] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2259 - 4051) -> ( 0 - 0), size 1792 -> 0

<7> [281.164818] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.165071] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.165315] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.165518] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.165751] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.165967] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [281.166143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.166319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.166507] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.166727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [281.167065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [281.167342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [281.167614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [281.167877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [281.168172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [281.169191] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.169476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.170191] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [281.170436] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [281.180564] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.213653] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.214040] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [281.214134] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.214287] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939

<7> [281.214523] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737

<7> [281.214541] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.214747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.214872] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.214978] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [281.215184] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [281.215405] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [281.215636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [281.215922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [281.216242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [281.216519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [281.216788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [281.217131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [281.217845] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.218164] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.263777] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.264316] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.264311] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.264616] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.264752] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.264990] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673

<7> [281.265210] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.265302] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692

<7> [281.265556] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333

<7> [281.265805] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353

<7> [281.266100] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.266359] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.266598] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.266834] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.267157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.267386] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [281.267634] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [281.267888] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [281.268282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [281.268658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [281.269028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [281.269422] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [281.269753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [281.270127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [281.271403] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.271751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.279985] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [281.297713] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.298055] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.330561] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.330896] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.331278] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452

<7> [281.331370] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.331575] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913

<7> [281.331809] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893

<7> [281.331776] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.332071] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793

<7> [281.332165] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.332293] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.332556] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [281.332781] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [281.333057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [281.333266] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.333470] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.333676] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.333897] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.334238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [281.334564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [281.334879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [281.335361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [281.335701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [281.336074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [281.337285] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.337589] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.347418] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.347610] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.380243] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.380513] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 452) -> ( 0 - 583), size 452 -> 583

<7> [281.380703] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 452 - 1365) -> ( 583 - 2898), size 913 -> 2315

<7> [281.380888] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2258) -> (2898 - 4051), size 893 -> 1153

<7> [281.381154] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0

<7> [281.381346] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.381299] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.381532] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.381654] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.381734] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.381961] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.381979] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.382128] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [281.382300] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.382466] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.382632] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.382837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [281.383350] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.383579] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 452) -> ( 0 - 583), size 452 -> 583

<7> [281.383764] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 452 - 1365) -> ( 583 - 2898), size 913 -> 2315

<7> [281.383961] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2258) -> (2898 - 4051), size 893 -> 1153

<7> [281.384138] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0

<7> [281.384310] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.384481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.384647] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.384832] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.385011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [281.385165] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.385319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.385474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.385636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [281.385884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [281.386177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [281.386421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [281.386660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [281.386911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [281.387965] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.388230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.388773] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [281.389026] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [281.397166] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.430234] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.430522] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [281.430724] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939

<7> [281.430923] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737

<7> [281.431198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.431395] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [281.431360] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.431588] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [281.431710] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.431813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [281.432014] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.432062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [281.432325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [281.432579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [281.432841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [281.433148] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [281.433423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [281.434262] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.434531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.480363] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.480730] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.481137] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673

<7> [281.481233] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.481441] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692

<7> [281.481679] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333

<7> [281.481676] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.481908] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353

<7> [281.482090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.482257] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.482481] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.482701] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.482940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.483173] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.483401] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [281.483654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [281.483880] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [281.484220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [281.484598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [281.484968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [281.485341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [281.485666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [281.486009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [281.487453] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.487796] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.496635] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [281.514238] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.514527] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.547036] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.547339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.547644] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452

<7> [281.547912] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913

<7> [281.548253] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893

<7> [281.548290] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.548492] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793

<7> [281.548723] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.548850] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.548976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [281.549219] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [281.549295] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.549448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [281.549676] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.549909] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.550207] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.550484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.550772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [281.551166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [281.551519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [281.551856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [281.552218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [281.552598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [281.553961] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.554324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.564017] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.564255] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.597163] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.597481] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 452) -> ( 0 - 585), size 452 -> 585

<7> [281.597717] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 452 - 1365) -> ( 585 - 2894), size 913 -> 2309

<7> [281.598009] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2258) -> (2894 - 4051), size 893 -> 1157

<7> [281.598140] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.598257] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0

<7> [281.598494] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.598582] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.598725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.598980] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [281.598986] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.599263] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [281.599499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [281.599713] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.599914] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.600185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.600435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [281.600817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [281.601170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [281.601496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [281.601801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [281.602150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [281.603279] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.603638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.604403] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [281.604703] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [281.613831] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.646959] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.647283] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [281.647519] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 585 - 2894) -> ( 376 - 3312), size 2309 -> 2936

<7> [281.647736] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2894 - 4051) -> (3312 - 4051), size 1157 -> 739

<7> [281.648004] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.648106] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.648232] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.648501] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [281.648527] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.648738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [281.648856] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.649039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [281.649368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [281.649688] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [281.650016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [281.650393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [281.650720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [281.651610] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.651954] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.697070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.697441] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.697782] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 376) -> ( 0 - 679), size 376 -> 679

<7> [281.698096] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 376 - 3312) -> ( 679 - 1358), size 2936 -> 679

<7> [281.698233] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.698331] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3312 - 4051) -> (1358 - 2705), size 739 -> 1347

<7> [281.698559] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2705 - 4051), size 0 -> 1346

<7> [281.698674] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.698783] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.699042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.699093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.699320] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [281.699540] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [281.699762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.700013] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.700220] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [281.700423] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [281.700666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [281.701019] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [281.701354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [281.701738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [281.702108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [281.702450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [281.703996] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.704342] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.713267] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [281.730955] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.731243] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.763735] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.764103] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.764221] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.764428] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 679) -> ( 0 - 456), size 679 -> 456

<7> [281.764661] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.764733] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 679 - 1358) -> ( 456 - 1360), size 679 -> 904

<7> [281.765011] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1358 - 2705) -> (1360 - 2259), size 1347 -> 899

<7> [281.765051] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.765227] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2705 - 4051) -> (2259 - 4051), size 1346 -> 1792

<7> [281.765449] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.765656] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.765903] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [281.766235] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [281.766467] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.766690] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.766898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [281.767157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [281.767416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [281.767761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [281.768155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [281.768555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [281.768880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [281.769228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [281.770466] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.770780] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.780662] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.780892] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.813722] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.814044] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 456) -> ( 0 - 814), size 456 -> 814

<7> [281.814132] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.814283] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 456 - 1360) -> ( 814 - 2440), size 904 -> 1626

<7> [281.814481] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1360 - 2259) -> (2440 - 4051), size 899 -> 1611

<7> [281.814467] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.814657] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2259 - 4051) -> ( 0 - 0), size 1792 -> 0

<7> [281.814741] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.814831] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.815061] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.815247] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [281.815436] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [281.815612] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.815785] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.815981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.816147] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.816314] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.816480] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [281.816650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 8, 8, 8, 8, 8, 0, 0, 19, 4, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [281.816818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [281.817027] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [281.817197] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.817369] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.817538] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [281.817745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [281.818072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [281.818359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [281.818647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [281.818894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [281.819191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [281.820146] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.820445] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.821133] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [281.821389] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [281.830539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.863580] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.864001] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [281.863971] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.864333] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [281.864423] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.864585] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [281.864826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.864784] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.865133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [281.865371] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [281.865648] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [281.865931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [281.866532] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.866820] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [281.867174] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [281.867399] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [281.867614] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.867834] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [281.868133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [281.868392] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [281.868654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [281.869023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [281.869368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [281.869679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [281.870041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [281.870411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [281.871312] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.871657] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.913624] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.914009] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.914101] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.914349] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896

<7> [281.914540] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.914607] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471

<7> [281.914837] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774

<7> [281.914941] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.915125] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910

<7> [281.915358] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.915579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.915815] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.916082] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.916327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.916544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [281.916755] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [281.916995] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [281.917245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [281.917873] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.918187] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.918497] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896

<7> [281.918694] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471

<7> [281.918878] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774

<7> [281.919146] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910

<7> [281.919348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.919546] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.919748] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.919993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.920216] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.920414] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [281.920605] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [281.920819] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [281.921096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [281.921436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [281.921778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [281.922131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [281.922433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [281.922737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [281.924022] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.924381] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.929925] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [281.947467] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.947709] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.980257] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.980566] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [281.980873] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676

<7> [281.981251] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691

<7> [281.981368] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [281.981496] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335

<7> [281.981738] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349

<7> [281.981807] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [281.982012] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.982241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [281.982228] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [281.982493] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [281.982746] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [281.983061] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [281.983297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [281.983530] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [281.983780] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [281.984105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [281.984504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [281.984853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [281.985226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [281.985557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [281.985870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [281.987175] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [281.987516] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [281.997134] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [281.997329] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.030293] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.030704] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 676) -> ( 0 - 814), size 676 -> 814

<7> [282.031073] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 676 - 1367) -> ( 814 - 2440), size 691 -> 1626

<7> [282.031137] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.031324] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2702) -> (2440 - 4051), size 1335 -> 1611

<7> [282.031560] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0

<7> [282.031575] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.031840] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.031969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.032116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [282.032348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [282.032587] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [282.032832] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [282.033115] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.033338] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.033573] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.033839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [282.034242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [282.034643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [282.034958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [282.035256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [282.035563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [282.036859] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.037238] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.037924] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [282.038209] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [282.047086] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.080195] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.080545] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [282.080793] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [282.081089] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [282.081149] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.081322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.081544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [282.081559] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.081762] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [282.081933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.082033] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [282.082270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [282.082580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [282.082872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [282.083195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [282.083467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [282.083752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [282.084607] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.084913] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.130305] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.130629] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.130956] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896

<7> [282.131073] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.131159] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471

<7> [282.131350] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774

<7> [282.131432] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.131531] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910

<7> [282.131710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.131727] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.131901] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [282.132072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [282.132270] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [282.132452] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.132610] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [282.132772] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [282.133015] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [282.133219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [282.133490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [282.133754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [282.134128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [282.134424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [282.134766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [282.136273] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.136688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.146561] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [282.164242] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.164586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.196848] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.197189] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.197474] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676

<7> [282.197728] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691

<7> [282.197975] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335

<7> [282.198101] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.198180] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349

<7> [282.198422] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.198484] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.198625] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [282.198797] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.198818] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [282.199062] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [282.199242] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.199424] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [282.199635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [282.199851] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [282.200158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [282.200487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [282.200790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [282.201139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [282.201429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [282.201710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [282.202978] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.203298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.213861] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.214103] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.247145] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.247454] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 676) -> ( 0 - 817), size 676 -> 817

<7> [282.247675] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 676 - 1367) -> ( 817 - 2434), size 691 -> 1617

<7> [282.247919] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2702) -> (2434 - 4051), size 1335 -> 1617

<7> [282.247942] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.248122] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0

<7> [282.248299] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.248355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.248549] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.248594] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.248737] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [282.248939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [282.249111] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [282.249278] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.249443] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.249610] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.249815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [282.250133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [282.250426] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [282.250702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [282.250978] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [282.251237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [282.252347] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.252646] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.253296] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [282.253547] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [282.263742] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.296914] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.297245] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [282.297509] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 817 - 2434) -> ( 588 - 2893), size 1617 -> 2305

<7> [282.297725] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2434 - 4051) -> (2893 - 4051), size 1617 -> 1158

<7> [282.297968] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.298060] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.298173] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.298370] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [282.298412] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.298605] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [282.298702] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.298863] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [282.299317] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.299560] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [282.299753] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 817 - 2434) -> ( 588 - 2893), size 1617 -> 2305

<7> [282.299959] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2434 - 4051) -> (2893 - 4051), size 1617 -> 1158

<7> [282.300139] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.300315] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.300512] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [282.300717] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [282.300959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [282.301243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [282.301511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [282.301782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [282.302086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [282.302367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [282.303139] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.303425] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.346994] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.347586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.347938] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.348055] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.348276] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 588) -> ( 0 - 905), size 588 -> 905

<7> [282.348525] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 588 - 2893) -> ( 905 - 1360), size 2305 -> 455

<7> [282.348495] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.348760] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2893 - 4051) -> (1360 - 3152), size 1158 -> 1792

<7> [282.348860] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.349034] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3152 - 4051), size 0 -> 899

<7> [282.349264] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.349485] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.349716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [282.349967] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [282.350183] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.350410] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.350652] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [282.350861] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [282.351185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [282.351581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [282.351956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [282.352291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [282.352617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [282.352977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [282.354499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.354831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.363138] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [282.380713] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.381068] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.413441] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.413699] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.413977] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 905) -> ( 0 - 681), size 905 -> 681

<7> [282.414073] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.414211] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 905 - 1360) -> ( 681 - 1362), size 455 -> 681

<7> [282.414411] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1360 - 3152) -> (1362 - 2707), size 1792 -> 1345

<7> [282.414412] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.414587] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3152 - 4051) -> (2707 - 4051), size 899 -> 1344

<7> [282.414685] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.414760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.414985] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.415213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [282.415397] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [282.415599] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.415775] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.416008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [282.416254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [282.416506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [282.417062] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.417282] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.417490] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 905) -> ( 0 - 681), size 905 -> 681

<7> [282.417701] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 905 - 1360) -> ( 681 - 1362), size 455 -> 681

<7> [282.417906] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1360 - 3152) -> (1362 - 2707), size 1792 -> 1345

<7> [282.418102] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3152 - 4051) -> (2707 - 4051), size 899 -> 1344

<7> [282.418286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.418483] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.418682] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [282.418852] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [282.419080] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.419267] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.419456] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [282.419624] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [282.419799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [282.420088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [282.420341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [282.420579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [282.420815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [282.421128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [282.422419] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.422708] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.430453] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.430655] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.463418] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.463708] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 681) -> ( 0 - 814), size 681 -> 814

<7> [282.463993] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 681 - 1362) -> ( 814 - 2440), size 681 -> 1626

<7> [282.464181] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1362 - 2707) -> (2440 - 4051), size 1345 -> 1611

<7> [282.464117] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.464365] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2707 - 4051) -> ( 0 - 0), size 1344 -> 0

<7> [282.464451] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.464545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.464720] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [282.464728] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.464925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [282.465110] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [282.465296] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [282.465468] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.465641] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.465806] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.466042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [282.466319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [282.466587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [282.466885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [282.467162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [282.467469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [282.468365] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.468652] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.469386] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [282.469656] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [282.480434] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.513425] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.513749] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [282.514094] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [282.514190] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.514320] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [282.514533] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.514595] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.514738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [282.514967] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [282.514932] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.515176] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [282.515433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [282.515723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [282.516053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [282.516364] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [282.516663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [282.516958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [282.517745] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.518076] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.563546] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.564029] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.564147] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.564470] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896

<7> [282.564624] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.564768] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471

<7> [282.565077] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774

<7> [282.565100] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.565328] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910

<7> [282.565577] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.565822] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [282.566110] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [282.566347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [282.566572] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.566787] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [282.567078] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [282.567338] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [282.567666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [282.568074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [282.568442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [282.568807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [282.569191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [282.569557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [282.570881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.571279] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.579793] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [282.597416] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.597739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.630153] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.630476] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.630783] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676

<7> [282.631093] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691

<7> [282.631219] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.631304] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335

<7> [282.631510] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349

<7> [282.631598] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.631707] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.631934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [282.631944] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.632130] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [282.632361] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [282.632575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.632757] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [282.632963] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [282.633136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [282.633337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [282.633619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [282.633911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [282.634189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [282.634460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [282.634708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [282.635762] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.636090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.647064] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.647278] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.680110] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.680430] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 676) -> ( 0 - 814), size 676 -> 814

<7> [282.680700] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 676 - 1367) -> ( 814 - 2440), size 691 -> 1626

<7> [282.680944] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2702) -> (2440 - 4051), size 1335 -> 1611

<7> [282.680996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.681141] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0

<7> [282.681330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.681351] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.681513] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [282.681641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.681708] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [282.681934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [282.682133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [282.682349] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.682544] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.682775] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.683049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [282.683393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [282.683705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [282.684032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [282.684370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [282.684648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [282.685793] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.686284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.687790] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [282.688130] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [282.697057] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.730070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.730354] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [282.730552] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [282.730739] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [282.730982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.731013] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.731177] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [282.731385] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [282.731368] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.731608] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [282.731659] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.731896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [282.732287] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.732515] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [282.732680] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [282.732874] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [282.733057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.733238] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [282.733420] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [282.733650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [282.733875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [282.734160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [282.734436] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [282.734703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [282.734993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [282.735316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [282.736172] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.736462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.780441] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.781035] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.781022] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.781367] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.781500] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.781721] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896

<7> [282.781933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.782084] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471

<7> [282.782316] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774

<7> [282.782590] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910

<7> [282.782820] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.783125] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [282.783362] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [282.783618] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [282.783878] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.784111] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [282.784347] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [282.784574] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [282.784918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [282.785281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [282.785622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [282.786050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [282.786437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [282.786810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [282.788443] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.788825] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.796435] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [282.814220] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.814553] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.846973] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.846992] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.847280] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.847434] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.847591] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676

<7> [282.847790] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.847937] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691

<7> [282.848177] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335

<7> [282.848423] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349

<7> [282.848654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.848914] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [282.849170] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [282.849429] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [282.849682] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.849939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [282.850165] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [282.850387] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [282.850657] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [282.851052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [282.851404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [282.851738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [282.852157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [282.852484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [282.853796] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.854168] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.863637] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.863860] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.896985] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.896980] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.897321] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 676) -> ( 0 - 817), size 676 -> 817

<7> [282.897394] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.897614] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 676 - 1367) -> ( 817 - 2434), size 691 -> 1617

<7> [282.897727] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.897864] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2702) -> (2434 - 4051), size 1335 -> 1617

<7> [282.898088] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0

<7> [282.898308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.898521] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.898757] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [282.899020] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [282.899230] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [282.899435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.899635] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.899851] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.900127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [282.900716] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.901025] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 676) -> ( 0 - 817), size 676 -> 817

<7> [282.901253] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 676 - 1367) -> ( 817 - 2434), size 691 -> 1617

<7> [282.901462] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2702) -> (2434 - 4051), size 1335 -> 1617

<7> [282.901660] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0

<7> [282.901881] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.902069] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.902265] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [282.902455] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [282.902640] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [282.902816] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.903048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.903242] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [282.903413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [282.903682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [282.903979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [282.904237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [282.904485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [282.904739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [282.905823] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.906134] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.906728] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [282.907029] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [282.913635] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.946726] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.947096] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [282.947091] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.947332] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 817 - 2434) -> ( 588 - 2893), size 1617 -> 2305

<7> [282.947549] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2434 - 4051) -> (2893 - 4051), size 1617 -> 1158

<7> [282.947528] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.947757] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.947865] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.948008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.948258] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [282.948459] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [282.948684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [282.949009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [282.949287] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [282.949558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [282.949885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [282.950179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [282.951033] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [282.951338] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [282.996880] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [282.997232] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [282.997547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 588) -> ( 0 - 905), size 588 -> 905

<7> [282.997781] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 588 - 2893) -> ( 905 - 1360), size 2305 -> 455

<7> [282.998109] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2893 - 4051) -> (1360 - 3152), size 1158 -> 1792

<7> [282.998225] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [282.998343] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3152 - 4051), size 0 -> 899

<7> [282.998573] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.998663] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [282.998797] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.999084] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [282.999042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [282.999292] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [282.999488] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [282.999678] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [282.999898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [283.000099] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [283.000322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [283.000638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [283.000972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [283.001308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [283.001628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [283.001961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [283.003526] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.003890] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.013036] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [283.030685] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [283.031056] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [283.063348] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [283.063638] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [283.063969] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 905) -> ( 0 - 681), size 905 -> 681

<7> [283.064057] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.064259] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 905 - 1360) -> ( 681 - 1362), size 455 -> 681

<7> [283.064477] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1360 - 3152) -> (1362 - 2707), size 1792 -> 1345

<7> [283.064460] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.064691] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3152 - 4051) -> (2707 - 4051), size 899 -> 1344

<7> [283.064797] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.064932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.065129] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [283.065344] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [283.065545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [283.065733] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.065972] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [283.066189] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [283.066404] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [283.066655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [283.067011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [283.067312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [283.067594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [283.067894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [283.068194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [283.069431] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.069739] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.080309] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [283.080505] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [283.113448] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 681) -> ( 0 - 2026), size 681 -> 2026

<7> [283.113731] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 681 - 1362) -> (2026 - 4051), size 681 -> 2025

<7> [283.114017] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1362 - 2707) -> ( 0 - 0), size 1345 -> 0

<7> [283.114150] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.114233] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2707 - 4051) -> ( 0 - 0), size 1344 -> 0

<7> [283.114439] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.114530] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.114638] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.114866] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.114871] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.115051] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.115241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.115422] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.115601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.115813] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.116047] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [283.116239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.116400] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.116571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.116747] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [283.116962] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.117150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.117342] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.117540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [283.117815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [283.118124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [283.118446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.118716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.119032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [283.119797] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.120129] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.120880] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [283.121145] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:35:plane 1A]

<7> [283.163357] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [283.163646] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [283.163939] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.164054] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.164180] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.164426] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.164459] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.164664] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.164791] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.164949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [283.165258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [283.165576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [283.165879] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [283.166225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [283.166524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [283.167420] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.167737] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.196677] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.197004] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [283.197084] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.197209] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [283.197386] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [283.197425] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.197555] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.197724] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.197695] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.197982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.198177] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.198368] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.198534] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [283.198700] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [283.198932] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [283.199112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [283.199371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [283.199622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [283.199887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [283.200165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [283.200441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [283.201684] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.202021] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.213535] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.246765] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.247180] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [283.247163] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.247432] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [283.247570] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.247664] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [283.247944] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.247950] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.248185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.248462] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.248738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.249049] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.249274] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.249497] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.249714] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.250060] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [283.250552] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.250870] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [283.251129] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [283.251349] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [283.251578] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.251792] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.252060] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.252255] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.252460] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.252655] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.252896] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.253103] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.253312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [283.253650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [283.254066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [283.254388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [283.254698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [283.255066] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [283.256069] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.256409] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.263581] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.296666] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [283.296954] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [283.297073] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.297156] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [283.297346] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.297407] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.297529] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.297676] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.297725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.297982] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.298185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [283.298406] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.298588] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.298827] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.299049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [283.299536] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [283.299747] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [283.299966] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [283.300147] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.300323] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.300506] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.300716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.300944] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [283.301119] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.301292] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.301450] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.301618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [283.301947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [283.302230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [283.302508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.302775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.303109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [283.303945] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.304246] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.330045] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [283.330330] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [283.330557] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.330767] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.331046] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.331169] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.331273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.331537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [283.331547] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.331866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [283.331897] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.332185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [283.332542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [283.332865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [283.333205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [283.334110] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.334402] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.363292] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.363617] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [283.363918] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [283.364043] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.364131] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [283.364322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.364422] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.364505] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.364686] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.364735] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.364930] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.365101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.365290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [283.365467] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [283.365631] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [283.365847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [283.366169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [283.366443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [283.366715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [283.367061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [283.367340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [283.368360] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.368659] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.380146] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.413715] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.413973] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.414251] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [283.414327] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.414533] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [283.414603] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.414768] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [283.415019] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.415241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.415459] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.415673] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.415898] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.416108] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.416319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.416529] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.416800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [283.417203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [283.417577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [283.417959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [283.418322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [283.418683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [283.420488] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.420839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.430106] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.463931] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [283.463869] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.464302] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [283.464450] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.464597] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [283.464906] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.464933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.465153] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [283.465392] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [283.465630] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [283.465883] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [283.466116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.466350] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.466586] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.466889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [283.467308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [283.467717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [283.468142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.468539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.468950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [283.470417] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.470820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.496843] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [283.496842] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.497121] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [283.497223] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.497348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.497564] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [283.497549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.497776] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [283.498008] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [283.498266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [283.498643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [283.499028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [283.499386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [283.499741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [283.500121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [283.501375] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.501697] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.530098] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.530440] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [283.530670] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [283.530926] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [283.530934] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.531146] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.531281] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.531356] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [283.531568] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [283.531600] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.531779] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [283.532021] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.532234] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [283.532442] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [283.532650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [283.532925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [283.533298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [283.533659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [283.534016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [283.534344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [283.534670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [283.536168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.536495] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.546874] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.580177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.580553] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [283.580870] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [283.580869] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.581119] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [283.581244] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.581354] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.581589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [283.581593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.581848] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [283.582086] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [283.582319] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.582547] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [283.582777] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [283.583029] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [283.583314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [283.583731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [283.584126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [283.584492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [283.584887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [283.585248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [283.586834] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.587189] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.596877] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.630144] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026

<7> [283.630482] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025

<7> [283.630744] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [283.631032] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.631035] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.631285] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.631406] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.631521] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.631755] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.631751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.632015] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [283.632250] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.632483] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.632716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.633014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [283.633394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [283.633757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [283.634138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.634497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.634871] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [283.636056] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.636411] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.680114] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [283.680414] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [283.680647] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.680918] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.680909] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.681143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.681253] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.681357] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.681567] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.681612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [283.682207] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [283.682436] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [283.682647] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.682877] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.683089] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.683297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.683523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [283.683908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [283.684271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [283.684631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [283.685025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [283.685381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [283.686418] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.686741] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.713458] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.713851] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [283.713843] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.714088] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [283.714186] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.714305] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [283.714517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.714499] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.714739] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.714981] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.715192] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.715399] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.715605] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [283.715837] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [283.716049] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [283.716300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [283.716878] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.717158] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [283.717382] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [283.717593] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [283.717844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.718061] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.718273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.718484] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.718695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.718928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [283.719125] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [283.719323] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [283.719531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [283.719868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [283.720182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [283.720479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [283.720761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [283.721055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [283.722037] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.722276] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.730105] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.763321] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.763689] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [283.763988] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [283.763997] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.764223] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [283.764442] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.764381] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.764655] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.764723] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.764917] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.765134] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.765345] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.765555] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.765765] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.765993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.766253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [283.766977] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.767262] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [283.767480] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [283.767690] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [283.767925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.768135] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.768348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.768559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.768767] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.768998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.769212] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.769423] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.769654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [283.770039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [283.770407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [283.770766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [283.771120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [283.771452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [283.772707] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.773055] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.780210] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.813286] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [283.813590] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [283.813921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [283.814059] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.814198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.814468] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.814539] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.814756] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.814996] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.815115] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.815395] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [283.815666] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.815945] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.816193] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.816497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [283.816915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [283.817261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [283.817600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.817969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.818351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [283.819396] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.819819] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.846658] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [283.847005] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [283.847141] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.847254] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.847486] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.847548] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.847730] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.847936] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.848023] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.848264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [283.848587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [283.848929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [283.849219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [283.849514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [283.849824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [283.850684] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.851030] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.879930] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.880246] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [283.880489] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [283.880683] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [283.880948] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.881071] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.881166] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.881395] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.881481] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.881597] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.881812] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.881839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.881992] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [283.882168] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [283.882375] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [283.882581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [283.882891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [283.883183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [283.883471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [283.883824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [283.884154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [283.885209] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.885522] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.896803] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.929928] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.930287] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [283.930553] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [283.930850] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [283.930989] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.931087] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.931310] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [283.931392] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.931531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [283.931731] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.931799] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [283.932011] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.932222] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [283.932427] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [283.932629] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [283.932916] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [283.933252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [283.933578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [283.934629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [283.934997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [283.935326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [283.936540] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.936913] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [283.946873] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [283.980170] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [283.980462] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [283.980701] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [283.980997] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [283.981128] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [283.981213] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [283.981419] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [283.981507] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [283.981661] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [283.981849] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [283.981908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [283.982100] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.982294] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.982480] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [283.982696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1390840 num active planes 2

<7> [283.983049] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [283.983383] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [283.983705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.984056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [283.984394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [283.985359] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [283.985699] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.013200] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [284.013469] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [284.013681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.013931] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.013967] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.014117] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [284.014332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [284.014350] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.014537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [284.014650] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.014826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [284.015103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [284.015373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.015646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.015937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [284.016746] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.017072] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.046603] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.046996] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [284.047089] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.047242] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [284.047472] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [284.047532] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.047689] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.048003] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.047974] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.048226] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [284.048437] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [284.048644] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.048940] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.049145] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [284.049332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [284.049547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [284.049876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [284.050231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [284.050548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [284.050895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [284.051211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [284.052387] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.052737] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.063469] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.096615] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.096995] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [284.097091] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.097230] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [284.097443] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [284.097468] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.097650] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.097823] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.097889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.098108] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [284.098338] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [284.098545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.098738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.098996] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [284.099192] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [284.099409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [284.099839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.100090] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [284.100342] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [284.100536] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [284.100741] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.100979] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.101165] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [284.101334] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [284.101518] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.101690] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.101925] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [284.102118] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [284.102322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [284.102607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [284.102903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [284.103211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.103495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.103814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [284.104872] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.105174] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.113400] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.146620] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691

<7> [284.146950] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360

<7> [284.147062] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.147178] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [284.147390] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.147439] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.147595] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.147748] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.147840] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.148045] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.148277] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.148472] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.148654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.148867] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.149038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [284.149239] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.149430] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.149589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.149822] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [284.150251] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691

<7> [284.150457] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360

<7> [284.150644] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [284.150866] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.151061] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.151258] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.151454] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.151623] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.151828] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.152038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.152237] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.152435] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [284.152627] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.152847] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.153046] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.153256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [284.153587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [284.153946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [284.154336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.154680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.155254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [284.156222] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.156548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.196599] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [284.197023] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [284.197152] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.197273] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.197504] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.197560] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.197725] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.197968] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.198048] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.198313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [284.198856] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [284.199116] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [284.199352] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.199579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.199895] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.200116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.200337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [284.200841] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [284.201088] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [284.201307] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.201564] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.201823] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.202027] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.202241] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [284.202583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [284.202970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [284.203307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.203634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.203995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [284.204868] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.205189] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.230269] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:494]

<7> [284.230934] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.231457] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.231942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.254153] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.254436] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [284.254607] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [284.254790] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [284.254942] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.255089] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.255231] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.255384] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.255535] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.255660] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [284.255801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [284.255917] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [284.256050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [284.256363] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.256495] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [284.256602] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [284.256705] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [284.256908] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.257010] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.257107] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.257208] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.257310] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.257406] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [284.257489] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [284.257579] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [284.257681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [284.257884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [284.258018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [284.258142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [284.258261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [284.258377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [284.258858] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.258983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.263330] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.296603] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.297176] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [284.297146] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.297623] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [284.297816] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.298053] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [284.298312] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.298433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.298773] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.299117] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.299429] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.299736] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.300136] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.300433] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.300730] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.301172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [284.301660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [284.302168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [284.302636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [284.303123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [284.303611] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [284.304845] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.305242] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.313306] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.346554] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [284.346921] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [284.347052] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.347192] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [284.347441] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.347487] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.347678] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.347969] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.347909] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.348221] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.348498] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [284.348721] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.349024] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.349244] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.349532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [284.350448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [284.350831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [284.351183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.351522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.351874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [284.352899] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.353243] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.379907] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [284.380236] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [284.380502] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.380793] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.380930] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.381061] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.381336] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.381405] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.381619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [284.381832] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.382045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [284.382412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [284.382779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.383163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.383542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [284.384630] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.385007] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.413142] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.413457] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [284.413728] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [284.414015] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [284.414228] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.414154] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.414440] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.414561] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.414633] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.414862] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.414933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.415070] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.415279] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [284.415467] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [284.415654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [284.415928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [284.416266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [284.416596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [284.416965] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [284.417330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [284.417681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [284.418807] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.419148] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.430097] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.463141] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.463491] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [284.463737] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [284.464084] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [284.464203] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.464339] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.464580] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.464637] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.464851] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.465040] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.465120] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.465332] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.465545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.465769] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.465993] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.466230] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [284.466558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [284.466925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [284.467298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [284.467607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [284.468000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [284.469207] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.469549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.480151] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.513342] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [284.513630] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [284.513932] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [284.514074] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.514154] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.514364] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.514454] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.514571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [284.514814] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [284.514793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.515020] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [284.515220] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.515446] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.515640] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.515909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [284.516224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [284.516535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [284.516859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.517154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.517452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [284.518334] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.518655] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.546523] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [284.546879] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [284.546911] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.547145] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.547386] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.547343] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.547621] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [284.547698] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.547933] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [284.548198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [284.548556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [284.548935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [284.549283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.549613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.550014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [284.551033] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.551381] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.579925] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.580317] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [284.580585] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [284.580884] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [284.581020] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.581133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.581374] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.581454] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.581614] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [284.581856] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.581934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [284.582145] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.582397] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.582602] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [284.582843] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [284.583080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [284.583564] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.583879] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [284.584090] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [284.584287] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [284.584524] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.584726] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.584998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [284.585256] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [284.585478] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.585694] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.585952] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [284.586164] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [284.586379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [284.586696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [284.587108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [284.587460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [284.587776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [284.588104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [284.589214] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.589497] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.596581] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.629914] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.630258] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [284.630503] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [284.630774] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [284.630905] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.630988] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.631195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.631285] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.631399] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [284.631598] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.631639] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [284.631896] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.632094] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.632290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [284.632486] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [284.632716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [284.633241] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.633518] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [284.633762] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [284.633970] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [284.634173] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.634404] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.634608] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [284.634850] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [284.635030] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.635199] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [284.635380] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [284.635564] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [284.635775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [284.636075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [284.636381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [284.636655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [284.636945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [284.637211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [284.638195] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.638476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.646571] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.679850] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691

<7> [284.680167] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360

<7> [284.680430] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0

<7> [284.680687] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.681020] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.681120] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.681298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.681568] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.681557] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.681838] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [284.681962] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.682049] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.682260] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.682517] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.682811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [284.683374] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691

<7> [284.683608] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360

<7> [284.683876] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0

<7> [284.684097] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.684348] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.684561] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.684833] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.685053] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [284.685264] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.685467] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.685658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.685910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [284.686220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [284.686526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [284.686855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.687162] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.687486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [284.688255] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.688557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.713091] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [284.713360] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [284.713575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.713841] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.713978] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.714054] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.714300] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.714356] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.714557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [284.714669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.714925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [284.715255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [284.715568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.715915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.716263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [284.717084] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.717377] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.746426] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.746811] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [284.746917] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.747066] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [284.747264] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [284.747328] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.747458] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.747654] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.747667] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.747904] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.748157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.748375] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.748601] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [284.748846] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [284.749037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [284.749262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [284.749581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [284.749922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [284.750280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [284.750600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [284.750932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [284.751822] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.752145] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.763517] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.796480] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.796929] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [284.796982] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.797280] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [284.797459] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.797553] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [284.797875] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.797908] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.798133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.798389] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.798697] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.799038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.799282] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.799524] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.799826] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.800106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [284.800485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [284.800912] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [284.801351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [284.801750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [284.802083] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [284.803192] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.803580] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.813275] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.846425] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [284.846702] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [284.847032] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [284.847151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.847275] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.847498] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.847556] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.847710] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.847917] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.848027] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.848241] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [284.848441] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.848637] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.848914] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [284.849156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [284.849478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [284.849807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [284.850113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.850409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [284.850696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [284.851668] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.852018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.879815] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [284.880076] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [284.880287] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.880490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.880799] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.880910] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.881058] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.881343] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.881349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [284.881702] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.881734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [284.882037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [284.882393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.882742] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [284.883045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [284.883923] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.884259] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.913053] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.913348] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [284.913550] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [284.913782] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [284.913978] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.913921] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.914172] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.914301] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.914355] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.914572] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.914615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.914821] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.914994] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [284.915176] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [284.915351] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [284.915545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [284.915823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [284.916074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [284.916327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [284.916630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [284.916920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [284.917930] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.918223] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.930051] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.963016] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [284.963310] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [284.963561] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [284.963819] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [284.963998] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.963959] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [284.964178] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [284.964350] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [284.964314] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [284.964530] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [284.964605] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [284.964697] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [284.964919] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [284.965089] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [284.965277] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [284.965485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [284.965779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [284.966059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [284.966322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [284.966589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [284.966935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [284.967952] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [284.968245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [284.979921] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [285.013230] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [285.013472] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [285.013667] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [285.013950] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.014149] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.014069] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.014340] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [285.014447] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.014567] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [285.014823] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [285.014783] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.015026] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.015211] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.015398] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.015611] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [285.016107] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [285.016303] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [285.016482] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [285.016655] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.016905] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.017077] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [285.017231] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [285.017389] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [285.017533] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.017674] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.017882] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.018051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 2

<7> [285.018325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [285.018601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [285.018946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [285.019231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [285.019545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [285.020428] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.020740] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.046427] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [285.046683] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [285.046975] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.047109] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.047180] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.047379] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [285.047462] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.047603] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [285.047787] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.047868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [285.048292] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [285.048498] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [285.048695] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.049010] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.049210] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [285.049415] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [285.049602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 2

<7> [285.049903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [285.050164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [285.050417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [285.050671] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [285.050958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [285.051689] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.051975] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.079854] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [285.080239] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [285.080565] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [285.080887] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [285.081001] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.081169] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.081425] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.081476] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.081677] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [285.081914] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.082036] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [285.082279] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.082499] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.082732] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [285.082948] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [285.083198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [285.083720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [285.083994] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [285.084204] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [285.084410] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [285.084610] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.084897] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.085103] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [285.085315] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [285.085523] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.085752] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.085961] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [285.086161] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [285.086373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [285.086716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [285.087053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [285.087359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [285.087635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [285.088101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [285.089269] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.089543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.096416] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [285.129696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [285.130041] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [285.130264] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [285.130454] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [285.130638] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.130885] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.130933] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.131086] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [285.131325] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [285.131291] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.131539] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.131582] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.131779] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.132002] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [285.132204] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [285.132438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [285.132944] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [285.133170] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [285.133357] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [285.133547] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [285.133760] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.133959] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.134137] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [285.134353] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [285.134559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.134742] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.134919] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [285.135094] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [285.135282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [285.135550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [285.135843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [285.136108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [285.136365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [285.136645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [285.137648] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.137966] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.146537] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:125:plane 4A]

<7> [285.179748] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.180092] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597

<7> [285.180338] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293

<7> [285.180566] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161

<7> [285.180853] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.180986] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.181063] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [285.181290] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [285.181365] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.181521] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [285.181673] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.181750] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.181934] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [285.182123] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [285.182299] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [285.182471] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.182639] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.182852] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [285.183042] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [285.183267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [285.183537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [285.184388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [285.184674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [285.184974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [285.185247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [285.186074] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.186367] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.196046] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:35:plane 1A]

<7> [285.196386] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [285.196534] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [285.213644] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.246339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.246659] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [285.246996] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [285.247099] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.247211] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [285.247412] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.247476] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.247609] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [285.247851] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [285.247837] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.248057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [285.248294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [285.248601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [285.248949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [285.249276] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [285.249596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [285.249925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [285.250729] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.251067] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.296407] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.296765] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.296870] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.297084] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [285.297278] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.297361] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [285.297582] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [285.297606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.297848] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [285.298077] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.298315] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [285.298564] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [285.298823] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [285.299044] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.299264] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [285.299488] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [285.299719] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [285.299947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [285.300260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [285.300572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [285.300921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [285.301293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [285.301607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [285.302726] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.303062] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.312712] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [285.330221] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.330515] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.362966] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.363216] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.363459] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [285.363744] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [285.363926] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [285.363865] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.364100] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [285.364197] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.364269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.364469] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [285.364469] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.364652] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [285.364878] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [285.365072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.365249] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [285.365425] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [285.365633] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [285.365903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [285.366195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [285.366476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [285.366775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [285.367096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [285.367364] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [285.368220] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.368520] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.379877] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.380081] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.412978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.413272] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [285.413496] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [285.413732] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [285.413926] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [285.413859] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.414114] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.414214] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.414297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [285.414479] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [285.414504] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.414658] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [285.414954] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [285.415166] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.415341] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.415545] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.415818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [285.416110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [285.416392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [285.416660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [285.416967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [285.417247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [285.418347] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.418648] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.419319] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [285.419578] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [285.429881] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.462996] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.463340] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [285.463621] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [285.463920] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [285.464050] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.464133] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.464336] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [285.464426] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.464538] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [285.464767] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [285.464773] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.465011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [285.465311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [285.465612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [285.465927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [285.466201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [285.466528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [285.467381] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.467659] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.513373] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.513843] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.513951] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.514278] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.514322] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.514634] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [285.514770] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.515016] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [285.515268] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [285.515510] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [285.515790] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.516062] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [285.516296] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [285.516525] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [285.516790] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.517013] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [285.517287] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [285.517531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [285.517839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [285.518219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [285.518598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [285.518986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [285.519320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [285.519639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [285.521078] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.521424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.529326] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [285.547079] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.547390] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.579855] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.580134] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.580412] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [285.580735] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [285.580748] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.580951] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [285.581158] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [285.581164] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.581361] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.581483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.581565] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [285.581801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [285.581996] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [285.582186] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.582372] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [285.582559] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [285.582790] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [285.583025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [285.583381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [285.583693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [285.583955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [285.584222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [285.584482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [285.585533] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.585853] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.596662] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.596889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.629780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.630077] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [285.630299] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [285.630490] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [285.630719] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [285.630901] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.630836] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.631075] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.631169] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.631248] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [285.631452] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [285.631444] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.631647] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [285.631893] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.632072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.632244] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.632447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [285.632944] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.633182] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [285.633403] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [285.633583] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [285.633792] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [285.633975] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.634143] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.634307] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [285.634470] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [285.634633] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [285.634861] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.635037] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.635203] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.635373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [285.635635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [285.635944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [285.636209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [285.636478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [285.636761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [285.637693] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.637973] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.638574] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [285.638842] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [285.646485] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.679596] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.679963] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [285.680246] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [285.680462] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [285.680699] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.680845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.680954] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.681180] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [285.681225] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.681407] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [285.681537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.681691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [285.681988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [285.682284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [285.682553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [285.682907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [285.683184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [285.684044] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.684341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.729795] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.730174] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.730515] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [285.730883] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [285.731019] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.731117] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [285.731393] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [285.731462] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.731621] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.731895] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.731884] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.732163] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [285.732379] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [285.732638] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.732912] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.733116] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [285.733318] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [285.733557] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [285.733932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [285.734269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [285.734605] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [285.734970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [285.735315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [285.736686] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.737023] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.745937] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [285.763536] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.763867] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.796302] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.796608] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.796995] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [285.797091] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.797301] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [285.797537] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [285.797528] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.797843] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [285.797950] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.798074] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.798298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.798522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [285.798847] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [285.799101] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.799334] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [285.799566] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [285.799842] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [285.800136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [285.800487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [285.800853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [285.801163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [285.801467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [285.801818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [285.802988] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.803315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.813217] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.813416] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.846176] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.846445] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597

<7> [285.846727] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293

<7> [285.846925] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161

<7> [285.846863] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.847114] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [285.847217] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.847298] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.847477] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [285.847504] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.847676] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [285.847894] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [285.848098] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [285.848286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.848448] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.848606] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [285.848839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [285.849132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [285.849420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [285.849716] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [285.850044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [285.850312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [285.851140] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.851435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.852206] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [285.852472] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [285.863327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.896168] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.896464] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [285.896774] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [285.896966] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [285.896907] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.897157] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.897241] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.897339] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [285.897518] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [285.897518] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.897768] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [285.898027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [285.898304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [285.898581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [285.898888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [285.899165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [285.899439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [285.900235] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.900526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.946170] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.946440] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [285.946721] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [285.946826] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [285.946913] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [285.947088] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [285.947161] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [285.947251] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [285.947411] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.947433] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [285.947570] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [285.947764] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [285.947951] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [285.948162] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [285.948330] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [285.948490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [285.948714] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [285.948939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [285.949231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [285.949504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [285.949812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [285.950131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [285.950390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [285.951201] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [285.951496] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [285.962612] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [285.980116] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [285.980405] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.012981] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.013227] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.013471] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [286.013765] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [286.013957] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [286.013889] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.014144] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [286.014240] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.014327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.014507] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [286.014531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.014716] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [286.014899] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [286.015105] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.015268] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [286.015428] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [286.015589] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [286.015843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [286.016131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [286.016411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [286.017240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [286.017523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [286.017809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [286.018615] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.018952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.029897] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.030111] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.063053] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.063336] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [286.063541] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [286.063787] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [286.063968] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [286.063915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.064147] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.064250] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.064322] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [286.064496] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [286.064524] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.064738] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [286.064928] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [286.065107] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [286.065286] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [286.065461] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [286.065692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [286.066011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [286.066280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [286.066542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [286.066832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [286.067116] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [286.068204] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.068485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.069120] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 786432 bytes of contiguous stolen space for FBC, limit: 2

<7> [286.069383] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [286.079752] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.112878] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.113175] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [286.113386] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [286.113584] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [286.113844] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.114036] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [286.113970] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.114244] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [286.114322] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.114459] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [286.114615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.114684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [286.115130] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.115364] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [286.115567] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [286.115795] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [286.115961] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.116150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [286.116308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [286.116478] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [286.116676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [286.116945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [286.117208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [286.117465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [286.117726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [286.118020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [286.118833] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.119141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.163005] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.163366] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.163741] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [286.163819] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.163976] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [286.164196] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [286.164226] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.164406] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [286.164561] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.164612] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.164872] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [286.165072] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [286.165297] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [286.165480] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.165683] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [286.165880] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [286.166074] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [286.166305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [286.166928] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.167171] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.167412] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [286.167607] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [286.167864] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [286.168098] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [286.168308] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.168522] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [286.168748] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [286.168976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [286.169158] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.169331] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [286.169506] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [286.169706] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [286.169888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [286.170189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [286.170482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [286.170793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [286.171107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [286.171392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [286.172488] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.172802] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.179221] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [286.196692] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.196961] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.229498] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.229807] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.229939] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.230061] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [286.230303] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [286.230292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.230493] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [286.230574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.230714] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [286.230887] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.231057] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [286.231257] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [286.231443] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [286.231607] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.231835] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [286.232035] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [286.232210] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [286.232414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [286.232709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [286.233002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [286.233300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [286.233583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [286.233935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [286.234911] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.235190] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.246443] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.246646] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.279801] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.279985] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.280198] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.280317] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [286.280542] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [286.280510] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.280788] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [286.280975] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [286.281156] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.281333] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [286.281510] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [286.281766] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [286.281968] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [286.282145] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [286.282327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [286.282505] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [286.282755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 1738550 num active planes 3

<7> [286.283055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [286.283345] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [286.283647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [286.283956] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [286.284225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [286.285285] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.285574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.286272] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 196608 bytes of contiguous stolen space for FBC, limit: 2

<7> [286.286526] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [286.296427] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.329543] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.329953] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [286.329966] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.330263] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [286.330370] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.330493] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [286.330749] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.330742] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.330966] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [286.331185] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [286.331446] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [286.331739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2433970 num active planes 3

<7> [286.332065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [286.332387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [286.332733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [286.333037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [286.333322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [286.334762] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.335080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.379521] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.379879] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.379983] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.380237] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [286.380364] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.380471] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [286.380720] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [286.380713] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.380925] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [286.381123] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.381318] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [286.381531] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [286.381801] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [286.382038] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.382233] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [286.382436] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [286.382681] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [286.382903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2086260 num active planes 4

<7> [286.383225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [286.383496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [286.383817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [286.384110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [286.384400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [286.385590] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.385948] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.395833] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [286.413214] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.413481] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.446155] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.446437] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.446757] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [286.446831] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.447010] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [286.447207] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [286.447214] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.447395] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [286.447496] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.447584] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.447814] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [286.447987] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [286.448190] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [286.448352] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.448510] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [286.448709] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [286.448889] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [286.449118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [286.449404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [286.449703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [286.449984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [286.450270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [286.450596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [286.451733] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.452042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.463145] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.463337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.496275] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.496577] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823

<7> [286.496877] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614

<7> [286.497090] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614

<7> [286.497027] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.497292] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [286.497405] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.497490] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.497723] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [286.497751] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.497919] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [286.498164] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:35:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [286.498382] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.498571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [286.498810] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [286.499000] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [286.499195] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.499386] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [286.499571] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [286.499811] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:125:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [286.499991] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [286.500176] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [286.500374] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [286.500543] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [286.500802] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 2781680 num active planes 3

<7> [286.501147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [286.501441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [286.501756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [286.502065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [286.502341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [286.503166] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.503447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.504088] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 49152 bytes of contiguous stolen space for FBC, limit: 2

<7> [286.504323] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:65:plane 2A]

<7> [286.513150] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.546177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.546496] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [286.546791] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [286.546999] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [286.546935] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.547198] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.547290] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.547387] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [286.547575] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [286.547572] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.547821] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [286.548024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [286.548407] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.548652] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [286.548827] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [286.549008] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [286.549184] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.549394] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [286.549598] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [286.550032] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [286.550238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3477100 num active planes 3

<7> [286.550533] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [286.550960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [286.551278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [286.551590] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [286.552001] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [286.552899] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.553232] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.596233] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.596798] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.596876] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.597185] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.597236] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.597506] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [286.597601] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.597805] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [286.598036] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [286.598263] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [286.598476] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.598719] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [286.598966] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [286.599178] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [286.599371] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.599562] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [286.599796] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [286.600000] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [286.600224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 3129390 num active planes 4

<7> [286.600520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [286.600846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [286.601187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [286.601481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [286.601793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [286.602703] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [286.603042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [286.612485] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:65:plane 2A]

<7> [286.630044] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.630352] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.662789] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.663051] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.663314] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [286.663540] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [286.663815] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [286.663940] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [286.664014] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [286.664256] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.664321] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [286.664460] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [286.664703] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [286.664661] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [286.664893] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [286.665079] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.665269] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [286.665474] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [286.665742] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [286.665980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:151:pipe A] data rate 4172520 num active planes 4

<7> [286.666542] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:35:plane 1A] using Y plane [PLANE:125:plane 4A]

<7> [286.666816] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:65:plane 2A] using Y plane [PLANE:135:plane 5A]

<7> [286.667048] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:35:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [286.667240] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:65:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [286.667423] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:125:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [286.667633] xe 0000:00:02.0: [drm:skl_print_plane_ddb_changes [xe]] [PLANE:135:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [286.667808] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.667976] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [286.668150] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [286.668327] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:65:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [286.668506] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [286.668704] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [286.668906] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [286.669083] xe 0000:00:02.0: [drm:skl_print_plane_wm_changes [xe]] [PLANE:135:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

Results for igt@kms_rotation_crc@multiplane-rotation-cropping-bottom