igt@kms_rotation_crc@multiplane-rotation-cropping-top on shard-lnl@xe-4627-e42f7566b0d3eba44a6aeeae2c810025c66c44ed Test details

Detail	Value
Duration	28.82 seconds
Hostname	shard-lnl-1
Igt-Version	IGT-Version: 2.3-g889245228 (x86_64) (Linux: 7.0.0-rc1-lgci-xe-xe-4627-e42f7566b0d3eba44-debug+ x86_64)
Out	Using IGT_SRANDOM=1772167070 for randomisation Opened device: /dev/dri/card0 Starting subtest: multiplane-rotation-cropping-top Subtest multiplane-rotation-cropping-top: SUCCESS (28.824s)
Err	Starting subtest: multiplane-rotation-cropping-top Subtest multiplane-rotation-cropping-top: SUCCESS (28.824s)
Dmesg	<6> [424.160440] Console: switching to colour dummy device 80x25 <6> [424.160746] [IGT] kms_rotation_crc: executing <7> [424.166295] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] <7> [424.166305] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1] <7> [424.166454] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected <7> [424.166682] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] <7> [424.166685] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2] <7> [424.166803] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected <7> [424.167031] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] <7> [424.167035] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3] <7> [424.167180] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected <7> [424.167455] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1] <7> [424.167458] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:392:eDP-1] <7> [424.167899] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7> [424.168283] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7> [424.168406] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [424.168511] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [424.168628] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5> [424.168632] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [424.168634] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [424.168635] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] DisplayID extension version 0x13, primary use 0x00 <7> [424.168637] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5> [424.168639] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [424.168640] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD monitor <5> [424.168642] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [424.168643] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD size 20, SAD count 0 <5> [424.168645] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [424.168656] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] VRR capable: yes <7> [424.168736] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [424.168816] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5> [424.169324] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [424.169327] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <5> [424.169328] [drm] DisplayID checksum invalid, remainder is 248 (ignoring) <7> [424.169386] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1] probed modes: <7> [424.169390] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [424.169395] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [424.169408] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] <7> [424.169412] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1] <7> [424.169556] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected <7> [424.169567] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] <7> [424.169571] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2] <7> [424.169687] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected <7> [424.169695] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] <7> [424.169698] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3] <7> [424.169799] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected <6> [424.170175] [IGT] kms_rotation_crc: starting subtest multiplane-rotation-cropping-top <7> [424.171593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0 <7> [424.171679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [424.171743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.171806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.171867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.171945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0 <7> [424.172061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400 <7> [424.172167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400 <7> [424.172269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [424.172358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [424.172441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0 <7> [424.172762] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.172861] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.172987] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2 <7> [424.195823] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A <7> [424.196199] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A <7> [424.196481] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [424.196698] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000 <7> [424.196853] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000 <7> [424.197024] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation <7> [424.197152] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [424.197298] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A] <7> [424.197483] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [fastset] <7> [424.197633] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [424.197768] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [424.197901] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid> <7> [424.198087] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [424.198214] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7> [424.198338] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7> [424.198460] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7> [424.198580] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [424.198699] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7> [424.198817] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7> [424.198932] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled <7> [424.199058] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7> [424.199170] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [424.199280] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8 <7> [424.199390] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7> [424.199499] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7> [424.199608] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7> [424.199711] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7> [424.199814] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7> [424.199915] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7> [424.200078] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7> [424.200174] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97 <7> [424.200268] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906 <7> [424.200362] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0 <7> [424.200453] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [424.200543] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [424.200633] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [424.200723] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [424.200810] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [424.200897] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855 <7> [424.200987] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7> [424.201072] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [424.201154] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [424.201235] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7> [424.201315] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no <7> [424.201395] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no, <7> [424.201473] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1. <7> [424.201551] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state: <7> [424.201628] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21 <7> [424.201704] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1 <7> [424.201781] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0 <7> [424.201858] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0 <7> [424.201940] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1 <7> [424.202038] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23 <7> [424.202116] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [424.202193] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [424.202268] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [424.202339] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [424.202409] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [424.202479] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [424.202552] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [424.202626] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [424.202699] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [424.202774] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [424.202848] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [424.202933] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [424.203022] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7> [424.212136] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1] <7> [424.212280] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A] <7> [424.232028] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.232462] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.232810] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.262765] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:429] <7> [424.284836] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026 <7> [424.285280] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025 <7> [424.285570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.285837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [424.286131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [424.286388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [424.286647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.286907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [424.287195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [424.287462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [424.287798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [424.288340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [424.288748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [424.289166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [424.289571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [424.289996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [424.291552] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.292004] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.295399] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [424.295754] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A] <7> [424.311918] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1 <7> [424.314283] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431] <7> [424.332001] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.332324] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.332539] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.336129] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.336391] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.363052] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432] <7> [424.364041] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.364646] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.365208] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.385141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [424.385276] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [424.385364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.385442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [424.385515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [424.385587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [424.385685] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [424.385808] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [424.385924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [424.386050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [424.386164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [424.386281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [424.386449] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 43464 kHz <7> [424.386917] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.387072] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.413572] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.414203] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.414654] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.415264] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433] <7> [424.437126] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.437296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [424.437384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [424.437463] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [424.437537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.437609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [424.437679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [424.437748] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [424.437817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.437885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [424.437971] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [424.438042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [424.438140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [424.438377] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.438497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [424.438579] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [424.438657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [424.438742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.438822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [424.438899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [424.439060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [424.439136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.439204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [424.439272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [424.439340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [424.439416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [424.439536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [424.439656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [424.439778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [424.439907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [424.440041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [424.440499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.440623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.446740] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434] <7> [424.460307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.479987] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435] <7> [424.479987] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.480408] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.480720] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.495821] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.496012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [424.496102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [424.496182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [424.496258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.496331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [424.496403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [424.496473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [424.496544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.496613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [424.496683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [424.496752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [424.496843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [424.497046] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.497150] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [424.497231] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [424.497308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [424.497390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.497473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [424.497551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [424.497622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [424.497695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.497768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [424.497842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [424.497917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [424.498008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [424.498131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [424.498245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [424.498357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [424.498469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [424.498584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [424.499125] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.499258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.513514] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436] <7> [424.529962] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.530222] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.530380] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.531638] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.532373] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.532533] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.562959] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:437] <7> [424.563982] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.564459] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.564890] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.592076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [424.592419] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [424.592649] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [424.592858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.593079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [424.593259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [424.593435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [424.593604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [424.593764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.593941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.594103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.594298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [424.594820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [424.594996] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [424.595184] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [424.595320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.595453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [424.595587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [424.595712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [424.595839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [424.596151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.596274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.596391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.596516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [424.596709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [424.596896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [424.597089] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [424.597261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [424.597430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [424.598179] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.598363] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.629010] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.629669] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438] <7> [424.629496] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.629914] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.662084] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [424.662281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [424.662365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.662445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [424.662520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [424.662591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [424.662702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [424.662825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [424.663101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [424.663220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [424.663334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [424.663446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [424.664222] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.664372] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.695971] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.696458] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.696957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.697307] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439] <7> [424.719178] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.719450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [424.719539] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [424.719618] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [424.719692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.719764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [424.719833] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [424.719902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [424.720019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.720094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [424.720165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [424.720236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [424.720339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [424.720463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [424.720578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [424.720691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [424.720803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [424.720929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [424.721643] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.721786] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.730228] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:440] <7> [424.744488] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.779962] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.780493] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:441] <7> [424.780553] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.781112] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.803761] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.804077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [424.804182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [424.804270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [424.804353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.804432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [424.804509] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [424.804587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [424.804662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.804736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [424.804810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [424.804882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [424.805013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [424.805141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [424.805257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [424.805371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [424.805483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [424.805594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [424.806168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.806287] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.813407] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:442] <7> [424.827740] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.863459] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:443] <7> [424.863940] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.864453] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.864953] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.895196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [424.895413] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [424.895498] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [424.895577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.895655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [424.895727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [424.895797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [424.895866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [424.896031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.896108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.896179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [424.896282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [424.896406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [424.896523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [424.896634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [424.896746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [424.896856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [424.897464] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.897606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.929571] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:444] <7> [424.929967] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.930406] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.930822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.958247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [424.958461] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [424.958550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.958627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [424.958703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [424.958775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [424.958884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [424.959032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [424.959151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [424.959267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [424.959378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [424.959490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [424.960165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.960313] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [424.979866] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:445] <7> [424.979915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [424.980180] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [424.980409] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [424.993978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [424.994136] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [424.994224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [424.994301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [424.994374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.994444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [424.994515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [424.994584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [424.994652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [424.994720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [424.994788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [424.994855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [424.994957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [424.995081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [424.995195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [424.995307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [424.995417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [424.995527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [424.996063] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [424.996186] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.014216] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:446] <7> [425.029922] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.030240] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.030462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.036675] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.037516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.037687] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.066946] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.067460] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.067969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.070538] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:447] <7> [425.094004] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.094261] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [425.094408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [425.094523] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [425.094631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.094737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.094842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [425.094976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [425.095070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.095161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.095250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [425.095347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [425.095478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [425.095608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [425.095731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [425.095851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [425.095989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [425.096105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [425.096650] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.096780] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.114747] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:448] <7> [425.128926] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.129192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.129390] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.131490] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.132203] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.132432] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.163413] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:449] <7> [425.163377] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.163919] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.164362] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.189759] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026 <7> [425.190048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025 <7> [425.190216] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [425.190374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.190519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [425.190659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [425.190816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [425.191026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [425.191163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.191300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.191450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.191608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [425.191899] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026 <7> [425.192014] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025 <7> [425.192122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [425.192225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.192325] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [425.192421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [425.192523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [425.192622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [425.192710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.192802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.193001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.193141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [425.193302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [425.193446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [425.193585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [425.193711] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [425.193833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [425.194363] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.194527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.194908] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [425.194924] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [425.194921] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4 <7> [425.195755] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:450] <7> [425.229149] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:451] <7> [425.229928] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.230482] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.230970] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.254363] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [425.254717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [425.254979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.255186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [425.255375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [425.255546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [425.255760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [425.256202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [425.256368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [425.256517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.256658] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [425.256805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [425.257020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [425.257170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [425.257495] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [425.257629] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [425.257756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.257894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [425.258029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [425.258153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [425.258280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [425.258472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [425.258655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [425.258832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [425.259015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [425.259186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [425.259920] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.260098] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.278928] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.279352] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.279723] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:452] <7> [425.279714] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.304064] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.304342] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [425.304514] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [425.304670] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [425.304801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.305092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [425.305250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [425.305383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [425.305497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.305600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [425.305702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [425.305806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [425.305962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [425.306229] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.306348] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [425.306437] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [425.306528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [425.306623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.306725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [425.306823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [425.306951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [425.307049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.307140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [425.307219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [425.307308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [425.307400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [425.307516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [425.307624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [425.307725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [425.307837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [425.307974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [425.308364] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.308484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.312660] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:453] <7> [425.323085] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.346083] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:454] <7> [425.346896] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.347263] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.347598] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.365977] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.366265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [425.366448] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [425.366610] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [425.366759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.366937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [425.367078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [425.367227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [425.367354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.367473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [425.367590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [425.367721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [425.367903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [425.368085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [425.368255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [425.368418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [425.368577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [425.368742] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [425.369459] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.369633] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.380169] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:455] <7> [425.395905] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.396352] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.396714] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.401486] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.402411] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.402717] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.429047] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:456] <7> [425.429018] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.429501] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.429978] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.449166] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [425.449521] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [425.449814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [425.450156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.450414] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [425.450668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [425.450995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [425.451236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [425.451473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.451704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.452134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.452405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [425.452740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [425.453112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [425.453450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [425.453816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [425.454161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [425.455183] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.455521] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.479578] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:457] <7> [425.479904] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.480390] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.480804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.504510] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [425.505113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [425.505352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.505562] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [425.505762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [425.505987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [425.506240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [425.506570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [425.506892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [425.507199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [425.507499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [425.507800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [425.509033] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.509309] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.528880] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.529392] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.529824] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.530692] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:458] <7> [425.554399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.554678] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [425.554787] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [425.554905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [425.555000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.555090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [425.555174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [425.555255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [425.555335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.555410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [425.555484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [425.555558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [425.555662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [425.555792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [425.556123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [425.556247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [425.556360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [425.556472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [425.557295] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.557450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.563409] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:459] <7> [425.574208] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.595879] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.596209] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.596470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.597960] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:460] <7> [425.613702] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.613870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [425.613959] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [425.614036] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [425.614109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.614181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [425.614251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [425.614320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [425.614390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.614458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [425.614527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [425.614595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [425.614681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [425.614801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [425.614926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [425.615040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [425.615152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [425.615262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [425.615794] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.616011] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.631198] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:461] <7> [425.645479] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.680050] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:462] <7> [425.679887] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.680473] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.680957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.698272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [425.698494] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [425.698604] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [425.698704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.698799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.698936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [425.699031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [425.699126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [425.699210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.699292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.699372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.699491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [425.699629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [425.699757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [425.699990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [425.700112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [425.700227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [425.700832] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.700957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.729578] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:463] <7> [425.729876] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.730350] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.730771] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.750116] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [425.750239] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [425.750322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.750399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.750472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [425.750543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [425.750633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [425.750755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [425.750981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [425.751096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [425.751208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [425.751319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [425.751817] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.751945] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.778854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.779271] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.779623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.780294] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:464] <7> [425.802226] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.802396] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [425.802487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [425.802569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [425.802647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.802721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.802794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [425.803104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [425.803176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.803244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.803312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [425.803380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [425.803469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [425.803655] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.803746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [425.803910] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [425.803983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [425.804053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.804123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.804194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [425.804262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [425.804330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.804397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.804464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [425.804531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [425.804605] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [425.804720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [425.804838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [425.804951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [425.805062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [425.805172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [425.805697] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.805838] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.813973] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:465] <7> [425.827524] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.846394] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:466] <7> [425.846851] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.847150] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.847346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.863045] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.863223] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [425.863311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [425.863388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [425.863462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.863534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.863604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [425.863673] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [425.863743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.863829] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.863900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [425.863969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [425.864056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [425.864239] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.864330] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [425.864400] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [425.864469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [425.864536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.864604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.864673] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [425.864742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [425.864936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.865008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [425.865076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [425.865143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [425.865217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [425.865332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [425.865445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [425.865555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [425.865664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [425.865775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [425.866391] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.866516] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.881375] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:467] <7> [425.893355] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [425.912030] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691 <7> [425.912299] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360 <7> [425.912477] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [425.912643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.912911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [425.912876] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.913074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [425.913226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [425.913236] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.913373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.913516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [425.913511] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.913652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [425.913786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [425.913928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [425.914059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.914189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.914316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.914480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [425.914936] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691 <7> [425.915070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360 <7> [425.915191] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [425.915308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.915421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [425.915535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [425.915647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [425.915763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.915916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [425.916030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [425.916139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [425.916248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [425.916349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.916452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.916554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [425.916666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [425.916854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [425.917027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [425.917186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [425.917342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [425.917497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [425.918112] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.918274] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [425.962093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [425.962389] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [425.962633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [425.962904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [425.963138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [425.963037] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [425.963365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [425.963537] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [425.963632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [425.964025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [425.964080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [425.964391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [425.964752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [425.965127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [425.965483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [425.966552] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [425.966934] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.000393] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.000936] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:468] <7> [426.000935] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.001367] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.021525] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.021859] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [426.021964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [426.022051] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [426.022131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.022207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.022280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.022349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.022419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.022486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [426.022555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [426.022624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [426.022728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [426.022862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [426.022979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [426.023091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.023201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.023311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [426.024008] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.024148] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.028848] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.062244] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.062860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [426.062869] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.063222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [426.063432] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.063552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [426.063944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.063961] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.064257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [426.064564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [426.064869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [426.065141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.065411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.065683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.065978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.066310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [426.066773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [426.067236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [426.067655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.068067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.068452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [426.068948] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 43464 kHz -> 65196 kHz <7> [426.070140] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.070469] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.078840] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.112108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [426.112466] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [426.112764] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [426.113099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.113109] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.113385] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.113549] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.113663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.113970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.113987] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.114239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [426.114500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.114766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.115032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.115319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [426.115731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [426.116961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [426.117367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [426.117753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [426.118155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [426.119454] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.119878] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.145291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [426.145553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [426.145819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.145826] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.146031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [426.146153] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.146237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [426.146441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [426.146457] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.146683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [426.147041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [426.147374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [426.147701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [426.148047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [426.148366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [426.149548] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.149897] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.178653] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.179012] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.179116] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [426.179378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [426.179383] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.179623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [426.179733] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.179901] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.180147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.180389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.180628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.180888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.181124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [426.181360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [426.181594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [426.181888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [426.182259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [426.182613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [426.182982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.183331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.183678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [426.185166] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.185536] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.195311] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.228665] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.228799] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.229066] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [426.229210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.229318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [426.229546] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [426.229566] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.229796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.230022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [426.230246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [426.230465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [426.230684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.230918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.231137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.231353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.231619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [426.232014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [426.232378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [426.232733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.233099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.233448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [426.234902] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.235245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.245449] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.278806] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.278988] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [426.279172] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.279271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [426.279514] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [426.279505] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.279745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.279993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.280222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [426.280444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [426.280662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [426.280900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.281120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.281333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.281592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [426.282174] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [426.282393] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [426.282596] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [426.282839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.283039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.283236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [426.283431] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [426.283632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [426.283865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.284071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.284266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.284481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [426.284845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [426.285178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [426.285501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [426.285840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [426.286167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [426.287331] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.287679] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.311980] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [426.312202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [426.312362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.312521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.312682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [426.312893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [426.312917] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.313108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [426.313320] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.313509] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [426.313606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.313669] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [426.313839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.313988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.314128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [426.314266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [426.314418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [426.314647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [426.314877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [426.315094] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [426.315298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [426.315501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [426.316343] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.316540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.345465] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.345912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [426.345862] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.346188] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [426.346278] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.346440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [426.346685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.346658] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.346961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.347210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [426.347451] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [426.347691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.347935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.348152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [426.348368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [426.348627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [426.349199] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.349492] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [426.349716] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [426.349960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [426.350179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.350394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.350611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [426.350840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [426.351053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.351266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.351484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [426.351697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [426.351940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [426.352307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [426.352664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [426.353040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.353389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.353713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [426.355134] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.355435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.362027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.395277] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.395677] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [426.396015] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [426.396076] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.396278] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [426.396531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.396544] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.396801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.396976] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.397049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [426.397290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [426.397530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.397801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.398039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [426.398274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [426.398559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [426.399327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.399643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [426.399896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [426.400112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [426.400327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.400544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.400784] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [426.401000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [426.401216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.401429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.401645] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [426.401888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [426.402123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [426.402483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [426.402860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [426.403213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.403561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.403923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [426.405315] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.405613] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.412337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.445234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691 <7> [426.445553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360 <7> [426.445894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0 <7> [426.446038] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.446141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.446378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.446473] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.446611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.446888] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.446954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.447197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [426.447443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.447712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.448056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.448324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [426.448707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [426.449102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [426.449505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [426.449862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [426.450195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [426.451039] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.451408] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.478639] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [426.479060] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [426.479189] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.479340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.479600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [426.479653] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.479904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [426.480081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.480140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [426.480455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [426.480817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [426.481170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [426.481505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [426.481993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [426.482368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [426.483220] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.483580] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.511868] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.512231] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [426.512501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [426.512724] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [426.513030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.513132] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.513265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.513515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.513563] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.513799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.514014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.513986] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.514224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [426.514436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [426.514666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [426.514995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [426.515320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [426.515637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [426.515991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.516320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.516624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [426.517574] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.517956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.528684] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.561830] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.562187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [426.562448] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [426.562689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [426.563030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.563162] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.563291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [426.563521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [426.563591] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.563771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [426.563991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.564019] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.564208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.564425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.564695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.565050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [426.565399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [426.565773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [426.566088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.566390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.566758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [426.567751] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.568096] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.578672] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.611843] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [426.612135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [426.612373] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [426.612600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.612876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.613010] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.613104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.613321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.613412] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.613554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [426.613781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.613796] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.613989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.614213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.614502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [426.614836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [426.615142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [426.615431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [426.615740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [426.616045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [426.616904] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.617235] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.645150] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [426.645444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [426.645681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.645997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [426.646084] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.646220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [426.646466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [426.646457] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.646709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [426.646804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.647055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [426.647367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [426.647647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [426.647966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [426.648304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [426.649306] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.649621] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.678488] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.678869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [426.678949] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.679137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [426.679353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [426.679353] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.679563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.679695] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.679817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.680022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.680274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.680506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.680700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [426.680940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [426.681117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [426.681333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [426.681622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [426.681970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [426.682288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.682581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.682901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [426.684055] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.684383] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.695405] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.728432] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.728790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [426.728894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.729070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [426.729301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [426.729295] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.729521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.729638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.729771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [426.729973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [426.730181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [426.730371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.730557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.730793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.730989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.731197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [426.731590] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.731857] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [426.732056] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [426.732268] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [426.732467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.732666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [426.732921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [426.733134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [426.733349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.733529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.733740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.733923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.734101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [426.734395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [426.734687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [426.735041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.735385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.735698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [426.736775] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.737078] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.745373] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.778827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [426.778878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.779135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [426.779310] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.779396] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [426.779641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.779685] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.779953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.780223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [426.780498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [426.780779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [426.781028] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.781267] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.781553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.781897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [426.782444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [426.782749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [426.782989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [426.783221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.783443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.783742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [426.783965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [426.784206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [426.784439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.784662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.784927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [426.785184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [426.785507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [426.785830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [426.786145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [426.786453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [426.786766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [426.787687] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.788070] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.811855] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [426.812172] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [426.812428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.812668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.812975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [426.813189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [426.813118] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.813451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [426.813520] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.813920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [426.813917] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.814134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [426.814340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.814534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.814751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [426.814970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [426.815196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [426.815628] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [426.815874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [426.816071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.816250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.816422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [426.816576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [426.816767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [426.817035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [426.817305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [426.817602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [426.817870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [426.818149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [426.818888] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.819130] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.845142] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.845537] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [426.845898] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [426.846037] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.846172] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [426.846436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.846506] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.846689] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.846957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.847009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [426.847303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [426.847596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.847921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.848146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [426.848357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [426.848616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [426.849264] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.849532] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [426.849745] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [426.849930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [426.850111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.850339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.850547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [426.850844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [426.851027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.851186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.851338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [426.851485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [426.851644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [426.851982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [426.852226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [426.852457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.852721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [426.852931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [426.853795] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.854029] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.858731] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turning VDD off <7> [426.858931] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 <7> [426.861827] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.895076] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.895420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [426.895666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [426.895975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [426.896208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.896142] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.896435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.896544] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.896651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [426.896965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [426.896919] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.897190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.897396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.897598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [426.897848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [426.898101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [426.898486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [426.898836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [426.899142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.899428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [426.899706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [426.900759] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.901075] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.912108] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [426.945068] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [426.945398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597 <7> [426.945660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293 <7> [426.945948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161 <7> [426.946147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.946087] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [426.946344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.946438] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [426.946543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.946805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.946770] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [426.947005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.947210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [426.947395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [426.947578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [426.947792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [426.947973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [426.948174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [426.948399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [426.948623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [426.949393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [426.949675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [426.949991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [426.950266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [426.950526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [426.951374] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [426.951719] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [426.961431] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A] <7> [426.961869] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [426.962026] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [426.979002] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.011720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.012025] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [427.012263] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [427.012466] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [427.012663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.012934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [427.013137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [427.013087] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.013353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [427.013467] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.013577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [427.013815] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.013892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [427.014198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [427.014459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [427.014723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [427.015018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [427.015757] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.016063] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.061835] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.062207] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.062601] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [427.063010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [427.063151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.063273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [427.063525] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [427.063628] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.063825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.064123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.064107] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.064361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.064592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.064865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.065078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [427.065304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [427.065522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [427.065807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [427.066146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [427.066487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [427.066865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [427.067211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [427.067558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [427.068669] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.069079] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.078082] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [427.095790] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.096122] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.128364] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.128640] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.128959] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [427.128996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.129195] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [427.129386] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [427.129343] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.129569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [427.129635] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.129786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.129966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [427.130152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [427.130363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [427.130543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.130737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.130916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.131091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.131316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [427.131625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [427.131940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [427.132246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [427.132505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [427.132810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [427.133762] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.134053] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.145310] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.145549] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.178710] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:469] <7> [427.178820] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.179217] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.179559] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.201060] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.201378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [427.201580] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [427.201833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [427.202034] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [427.202229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.202418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.202622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.202878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.203046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [427.203209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.203373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.203531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.203752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [427.204028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [427.204297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [427.204563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [427.204840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [427.205080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [427.206127] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.206358] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.206888] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [427.207076] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [427.212196] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.245092] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.245447] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [427.245834] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [427.245958] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.246093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [427.246329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.246394] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.246563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [427.246860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [427.246814] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.247109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [427.247412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [427.247987] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.248298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [427.248542] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [427.248822] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [427.249085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.249319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [427.249567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [427.249859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [427.250147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [427.250524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [427.250917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [427.251300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [427.251648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [427.252080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [427.253214] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.253576] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.295147] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.295585] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.295955] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.295985] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.296305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [427.296420] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.296552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [427.296833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [427.296842] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.297063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [427.297294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.297517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.297813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.298083] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.298313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.298549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [427.298815] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [427.299019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [427.299315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [427.299622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [427.299974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [427.300354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [427.300730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [427.301077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [427.302233] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.302576] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.311390] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [427.329057] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.329352] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.361693] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.361963] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.362222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [427.362480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [427.362725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [427.362927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [427.362878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.363123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.363252] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.363314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [427.363510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [427.363578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.363727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [427.363917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.364112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.364308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.364496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.364746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [427.365309] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.365563] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.366307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [427.366507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [427.366711] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [427.366925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [427.367159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.367373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [427.367559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [427.367788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [427.368003] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.368173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.368356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.368523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.368733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [427.369003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [427.369278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [427.369539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [427.369868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [427.370146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [427.371104] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.371412] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.378608] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.378832] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.412241] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:470] <7> [427.412711] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.413151] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.413490] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.434320] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.434688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [427.434906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [427.435112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [427.435308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [427.435501] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.435718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [427.435897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [427.436102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [427.436291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [427.436487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.436714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.436909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.437131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [427.437409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [427.437695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [427.437940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [427.438187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [427.438417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [427.439312] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.439545] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.440111] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [427.440286] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [427.445559] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.478327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.478702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [427.478818] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.479021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [427.479274] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [427.479252] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.479514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.479630] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.479812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [427.480125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [427.480389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [427.480710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [427.481096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [427.481467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [427.481870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [427.482235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [427.482614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [427.483853] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.484295] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.528502] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.528956] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.529377] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [427.529738] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [427.529872] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.530019] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [427.530293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [427.530392] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.530561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.530935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [427.530903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.531196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [427.531454] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [427.531744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.532002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [427.532224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [427.532445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [427.532745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [427.533149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [427.533547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [427.533995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [427.534454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [427.534900] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [427.536447] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.536930] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.544692] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [427.562192] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.562451] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.594971] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.595261] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.595544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [427.595902] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [427.596106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [427.596060] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.596305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [427.596433] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.596498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.596784] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [427.596798] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.596969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [427.597157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [427.597354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.597533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [427.597761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [427.597956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [427.598180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [427.598497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [427.598830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [427.599117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [427.599404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [427.599714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [427.600775] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.601093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.611940] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.612149] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.644974] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.645346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597 <7> [427.645577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293 <7> [427.645871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161 <7> [427.645934] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.646082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [427.646282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.646309] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.646475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.646695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.646674] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.646880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.647068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [427.647304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.647493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.647694] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.647933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [427.648247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [427.648558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [427.648908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [427.649203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [427.649482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [427.650387] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.650735] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.651552] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [427.651882] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [427.661984] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.694952] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.695297] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [427.695573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [427.695898] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [427.696117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.696040] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.696322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [427.696419] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.696521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [427.696808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [427.696776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.697039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [427.697321] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [427.697593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [427.697935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [427.698275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [427.698606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [427.699433] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.699774] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.745071] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.745514] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.745862] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.746005] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.746141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [427.746334] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [427.746359] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.746517] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [427.746728] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [427.746679] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.746899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.747060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.747233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.747421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.747587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.747846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [427.748026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [427.748222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [427.748435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [427.748738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [427.749028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [427.749313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [427.749668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [427.749946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [427.750945] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.751291] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.761305] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [427.779023] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.779359] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.811731] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.812026] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.812269] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [427.812474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [427.812712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [427.812891] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [427.812841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.813066] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.813235] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [427.813199] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.813404] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [427.813476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.813623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [427.813799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.813984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.814171] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.814358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.814569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [427.814907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [427.815191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [427.815479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [427.815783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [427.816048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [427.816887] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.817193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.828712] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.828924] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.869015] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:471] <7> [427.868784] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.869292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.869729] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.892842] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.893320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [427.893585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [427.893857] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [427.894083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [427.894298] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.894508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.894776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.894981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.895182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [427.895380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.895578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.895794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.896050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [427.896767] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.897027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [427.897219] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [427.897398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [427.897573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [427.897758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.897936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.898099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.898258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.898418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [427.898567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.898733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.898883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [427.899043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [427.899284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [427.899516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [427.899744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [427.899961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [427.900165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [427.901378] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.901588] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.902095] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [427.902244] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [427.911967] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.945133] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.945659] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.945730] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [427.946178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [427.946173] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.946528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [427.946647] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.946951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.947294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [427.947690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [427.948044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [427.948489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [427.949032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [427.949450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [427.949955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [427.950427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [427.950870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [427.952156] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [427.952677] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [427.995288] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [427.995780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [427.995772] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [427.996235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [427.996324] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [427.996529] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [427.996877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [427.996831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [427.997146] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [427.997462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.997772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [427.998038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [427.998288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [427.998530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [427.998840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [427.999181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [427.999418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [427.999749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [428.000139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [428.000569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [428.001055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [428.001472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [428.001882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [428.003286] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.003705] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.011260] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [428.028419] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.028774] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.061648] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.061978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.062307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [428.062676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [428.062818] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.062918] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [428.063151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [428.063250] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.063384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.063660] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.063702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [428.063949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [428.064172] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [428.064395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.064641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [428.064870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [428.065109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [428.065432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [428.065844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [428.066173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [428.066496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [428.066885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [428.067223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [428.068331] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.068688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.078544] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.078798] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.112233] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:472] <7> [428.112758] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.113278] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.113736] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.133539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.134122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [428.134430] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [428.134714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [428.134945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [428.135178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.135394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.135771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [428.136019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [428.136256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [428.136454] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.136683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.136878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.137096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [428.137385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [428.137684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [428.138004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [428.138253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [428.138488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [428.139359] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.139615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.140189] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [428.140390] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [428.145450] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.178207] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.178524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [428.178900] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [428.178897] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.179139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [428.179276] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.179365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.179604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.179663] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.179828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [428.180115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [428.180417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [428.180812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [428.181226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [428.181621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [428.182077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [428.182478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [428.183560] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.184023] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.228339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.228728] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.228834] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.229049] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [428.229261] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [428.229210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.229460] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [428.229523] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.229689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [428.229880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.230069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.230270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [428.230488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [428.230726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.230890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.231052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [428.231250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [428.231485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [428.231812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [428.232100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [428.232381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [428.232726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [428.233042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [428.234293] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.234640] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.244576] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [428.262098] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.262393] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.295066] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.295398] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.295796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [428.295877] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.296078] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [428.296321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [428.296309] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.296582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [428.296717] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.296814] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.297067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.297306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [428.297520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [428.297794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.298018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.298259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [428.298525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [428.298870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [428.299183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [428.299482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [428.299824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [428.300189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [428.300506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [428.301686] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.302026] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.311973] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.312170] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.345069] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.345384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823 <7> [428.345673] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614 <7> [428.345796] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.345920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614 <7> [428.346155] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [428.346229] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.346382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.346641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [428.346634] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.346865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [428.347068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [428.347265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.347456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [428.347697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [428.347890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [428.348089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.348286] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [428.348482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [428.348777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [428.348970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [428.349156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.349340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.349520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.349805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [428.350121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [428.350454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [428.350820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [428.351146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [428.351416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [428.352322] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.352614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.353360] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [428.353647] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [428.361838] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.394816] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.395082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [428.395321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [428.395516] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [428.395757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.395948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [428.395882] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.396134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [428.396230] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.396341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [428.396519] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.396567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [428.397017] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.397224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [428.397390] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [428.397569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [428.397731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.397895] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [428.398064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [428.398232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [428.398412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [428.398710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [428.398962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [428.399210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [428.399451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [428.399764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [428.400426] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.400734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.444866] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.445148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.445408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [428.445698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [428.445812] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.445887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [428.446068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [428.446160] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.446247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.446419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [428.446463] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.446620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [428.446791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [428.446981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.447144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [428.447306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [428.447465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [428.447698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [428.448166] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.448365] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.448581] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [428.448741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [428.448895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [428.449042] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [428.449189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.449358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [428.449508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [428.449706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [428.449854] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.449996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [428.450138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [428.450280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [428.450427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [428.450706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [428.450969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [428.451211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [428.451497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [428.451779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [428.452561] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.452816] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.461202] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [428.478496] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.478772] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.511502] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.511841] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.512108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [428.512359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [428.512582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [428.512708] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.512771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [428.512995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.513059] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.513190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [428.513365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [428.513355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.513559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [428.513729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.513886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [428.514045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [428.514204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [428.514393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [428.514678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [428.514932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [428.515192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [428.515446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [428.516123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [428.516919] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.517206] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.528425] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.528732] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.561451] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.561749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823 <7> [428.561949] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614 <7> [428.562141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614 <7> [428.562325] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [428.562504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.562741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [428.562922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [428.562870] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.563103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [428.563276] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [428.563218] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.563446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.563517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.563663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.563862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.564061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [428.564326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [428.564601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [428.564914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [428.565166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [428.565410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [428.566449] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.566741] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.567306] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [428.567548] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [428.578333] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.611476] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.611791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [428.612002] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [428.612204] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [428.612398] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.612690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [428.612807] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.612925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [428.613141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [428.613204] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.613370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [428.613516] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.613701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [428.614026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [428.614297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [428.614573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [428.614864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [428.615573] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.615847] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.661564] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.661889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.662248] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [428.662481] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [428.662761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [428.662946] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [428.662891] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.663125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.663244] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.663301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [428.663491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [428.663578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.663751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [428.663926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.664095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [428.664261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [428.664426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [428.664660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [428.664933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [428.665197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [428.665515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [428.665831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [428.666089] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [428.667242] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.667561] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.677810] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [428.695396] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.695742] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.728101] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.728350] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.728649] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [428.728636] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.728875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [428.728992] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.729064] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [428.729248] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [428.729286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.729430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.729644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [428.729839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [428.730006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [428.730175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.730341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [428.730505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [428.730769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [428.730989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [428.731261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [428.731537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [428.731801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [428.732073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [428.732373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [428.733359] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.733665] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.745113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.745333] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.778336] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.778635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826 <7> [428.778735] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.778830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605 <7> [428.779012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620 <7> [428.779063] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.779192] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [428.779332] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.779369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.779572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.779749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [428.779956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [428.780145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [428.780314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.780481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.780725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.780928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [428.781179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [428.781425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [428.781715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [428.781952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [428.782184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [428.783058] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.783315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.783976] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [428.784198] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [428.795104] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.828130] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.828410] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [428.828673] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289 <7> [428.828860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164 <7> [428.828809] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.829040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.829134] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.829217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.829392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [428.829405] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.829639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [428.829844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [428.830234] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.830438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [428.830638] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289 <7> [428.830799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164 <7> [428.830964] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.831125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.831295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [428.831487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [428.831707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [428.831971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [428.832234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [428.832530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [428.832788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [428.833026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [428.833891] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.834155] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.878127] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.878554] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.878662] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.878902] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.878924] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.879222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913 <7> [428.879202] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.879426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452 <7> [428.879651] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794 <7> [428.879832] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892 <7> [428.880009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.880183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.880355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [428.880589] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [428.880757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.880918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.881079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [428.881273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [428.881486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [428.881801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [428.882069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [428.882335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [428.882624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [428.882932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [428.883978] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.884256] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.894465] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [428.911871] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.912131] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.944781] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.945046] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.945325] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691 <7> [428.945612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676 <7> [428.945643] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.945827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350 <7> [428.946026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334 <7> [428.946015] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.946225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.946326] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.946420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.946656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [428.946860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [428.947076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.947267] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.947442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [428.947662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [428.947885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [428.948369] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.948597] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.948803] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691 <7> [428.948994] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676 <7> [428.949168] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350 <7> [428.949322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334 <7> [428.949474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.949680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.949843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [428.950004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [428.950166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.950360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [428.950555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [428.950717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [428.950889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [428.951137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [428.951380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [428.951663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [428.951919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [428.952173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [428.953066] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [428.953321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [428.961699] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.961901] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [428.994747] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [428.995030] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 691) -> ( 0 - 823), size 691 -> 823 <7> [428.995244] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 691 - 1367) -> ( 823 - 2437), size 676 -> 1614 <7> [428.995451] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2717) -> (2437 - 4051), size 1350 -> 1614 <7> [428.995722] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0 <7> [428.995908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [428.995854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [428.996131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [428.996206] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [428.996326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [428.996561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [428.996540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [428.996745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [428.996929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.997114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.997300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [428.997539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [428.997835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [428.998123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [428.998404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [428.998760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [428.999009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [428.999758] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.000048] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.000860] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [429.001137] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [429.011604] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.044747] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.045073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [429.045355] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [429.045641] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [429.045772] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.045859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.046063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.046146] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.046266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.046528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.046458] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.046764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [429.047042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [429.047309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [429.047592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [429.047856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [429.048121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [429.048804] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.049113] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.094778] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.095080] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.095422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [429.095715] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [429.095910] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [429.095841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.096095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [429.096191] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.096279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.096459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.096521] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.096740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.096925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.097102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.097260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [429.097414] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [429.097600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [429.097788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [429.098058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [429.098322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [429.098619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [429.098921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [429.099163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [429.099976] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.100256] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.111097] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [429.128433] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.128747] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.161355] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.161627] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.161870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [429.162079] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [429.162263] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [429.162442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [429.162688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.162869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.162800] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.163048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.163145] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.163262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.163465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.163446] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.163692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.163862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.164030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.164223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [429.164494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [429.164748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [429.165003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [429.165258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [429.165576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [429.166416] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.166736] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.178308] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.178581] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.211349] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.211667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823 <7> [429.211922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614 <7> [429.212126] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614 <7> [429.212319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [429.212549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.212743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.212675] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.212931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.213044] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.213160] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.213380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [429.213366] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.213639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.213847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.214032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.214233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [429.214520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [429.214792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [429.215057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [429.215312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [429.215608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [429.216679] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.216960] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.217594] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [429.217825] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [429.228541] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.261792] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.262376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [429.262821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [429.262838] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.263134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [429.263434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.263401] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.263776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.263936] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.264085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.264372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.264765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [429.265591] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.265969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [429.266261] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [429.266582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [429.266864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.267146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.267425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.267728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.268031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [429.268516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [429.268963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [429.269388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [429.269834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [429.270271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [429.271934] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.272369] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.311739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.312281] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.312670] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.312640] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.313033] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [429.313042] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.313304] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [429.313413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.313593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [429.313847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [429.314095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.314346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.314630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.314876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.315115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.315359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [429.315622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [429.315867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [429.316175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [429.316628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [429.317023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [429.317413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [429.317845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [429.318243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [429.320187] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.320634] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.327703] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [429.346848] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.347209] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.378508] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.378633] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.378954] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.379025] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.379346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.379439] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [429.379762] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [429.380025] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [429.380273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [429.380546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.380793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.381042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.381291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.381581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.381830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.382074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.382316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.382645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [429.383071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [429.383492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [429.383883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [429.384276] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [429.384706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [429.386638] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.387076] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.395444] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.395703] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.428503] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.428658] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.428990] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.429117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826 <7> [429.429438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605 <7> [429.429403] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.429789] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620 <7> [429.430074] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [429.430346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.430643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [429.430896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [429.431140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [429.431386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [429.431653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.431902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.432144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.432468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [429.433321] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.433706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826 <7> [429.433963] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605 <7> [429.434210] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620 <7> [429.434470] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [429.434711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.434957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [429.435203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [429.435475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [429.435726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [429.435964] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.436204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.436443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.436728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [429.437141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [429.437562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [429.437925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [429.438280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [429.438637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [429.440070] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.440375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.441167] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [429.441396] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [429.445285] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.478304] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.478800] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.478891] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [429.479210] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289 <7> [429.479296] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.479537] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164 <7> [429.479820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.479773] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.480098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [429.480375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [429.480685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [429.481024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [429.481522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [429.481966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [429.482401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [429.482856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [429.483282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [429.484836] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.485275] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.528177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.528549] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.528531] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.528882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913 <7> [429.528893] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.529122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452 <7> [429.529226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.529347] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794 <7> [429.529578] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892 <7> [429.529801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.530025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [429.530247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [429.530491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [429.530720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.530933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [429.531146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [429.531359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [429.531660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [429.532013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [429.532354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [429.532701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [429.533052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [429.533399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [429.535186] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.535601] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.544326] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [429.562369] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.562741] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.594933] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.595346] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.595749] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.595821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691 <7> [429.596127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676 <7> [429.596178] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.596413] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350 <7> [429.596613] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.596717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334 <7> [429.596989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.597264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [429.597567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [429.597843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [429.598112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.598372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [429.598684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [429.598950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [429.599279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [429.599781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [429.600231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [429.600693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [429.601130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [429.601585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [429.603637] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.604104] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.611959] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [429.612214] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [429.644796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 691) -> ( 0 - 2026), size 691 -> 2026 <7> [429.645126] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 691 - 1367) -> (2026 - 4051), size 676 -> 2025 <7> [429.645421] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2717) -> ( 0 - 0), size 1350 -> 0 <7> [429.645800] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0 <7> [429.645943] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.646056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.646359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.646414] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.646678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.646907] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.646948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.647234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.647502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.647736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.647969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.648194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [429.648422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.648728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.648972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.649198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [429.649418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.649714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.649985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.650281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [429.650732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [429.651141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [429.651473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [429.651788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [429.652075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [429.652957] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.653259] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.653943] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [429.654189] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A] <7> [429.677970] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [429.678247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [429.678540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.678674] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.678765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.678981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.679089] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.679202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.679462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [429.679467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.679755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [429.680050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [429.680347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [429.680728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [429.681018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [429.681658] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.681915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.711300] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [429.711617] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [429.711713] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.711875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [429.712076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [429.712113] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.712269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.712486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.712482] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.712680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.712930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.713140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.713338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [429.713581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [429.713798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [429.714046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [429.714374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [429.714771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [429.715098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [429.715414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [429.715776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [429.716647] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.716942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.728070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [429.761294] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [429.761638] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [429.761727] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.761912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [429.762108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [429.762085] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.762297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.762385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.762517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.762701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.762921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.763122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.763293] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.763497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.763670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.763870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [429.764298] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [429.764583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [429.764766] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [429.764937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [429.765101] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.765268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.765867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.766045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.766202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.766356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.766550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.766713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.766902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [429.767173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [429.767476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [429.767738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [429.767999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [429.768238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [429.769084] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.769359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.778148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [429.811361] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [429.811709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [429.811839] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.811933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [429.812141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.812207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.812345] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.812588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.812563] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.812785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.812972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [429.813184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.813384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.813637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.813837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [429.814223] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [429.814406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [429.814636] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [429.814808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.815022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.815187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.815354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.815558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [429.815719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.815911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.816070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.816239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [429.816528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [429.816784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [429.817039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [429.817288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [429.817569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [429.818317] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.818623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.844666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [429.844947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [429.845209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.845494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.845643] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.845730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.845994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.846052] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.846251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [429.846396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.846723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [429.846916] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [429.847102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.847312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.847531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.847703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.847874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [429.848246] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [429.848439] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [429.848593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.848744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.848906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.849079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.849244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [429.849541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [429.849757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [429.849968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [429.850165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [429.850387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [429.851034] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.851237] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.877911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [429.878227] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [429.878548] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [429.878559] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.878750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [429.878939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.878909] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.879113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.879187] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.879284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.879490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.879659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.879825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [429.879993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [429.880158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [429.880347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [429.880809] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [429.881011] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [429.881162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [429.881307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [429.881564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.881723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.881890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.882036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.882171] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.882295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [429.882480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [429.882606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [429.882732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [429.882958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [429.883152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [429.883335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [429.883539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [429.883712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [429.884536] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.884709] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.895040] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [429.927929] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [429.928278] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [429.928668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [429.928810] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.928901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [429.929125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.929206] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.929396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [429.929601] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.929679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [429.929879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [429.930114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.930313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [429.930599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [429.930804] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [429.931023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [429.931295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [429.931587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [429.931866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [429.932143] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [429.932427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [429.933464] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.933746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [429.944768] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [429.978180] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [429.978453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [429.978468] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [429.978665] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [429.978807] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [429.978857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [429.979037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [429.979090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [429.979215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [429.979439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [429.979632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [429.979823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.980001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.980175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [429.980381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [429.980698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [429.980953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [429.981210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [429.981468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [429.981715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [429.982598] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [429.982866] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.011244] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [430.011524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [430.011728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.011670] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.011927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.012013] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.012123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [430.012304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.012355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [430.012637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [430.012951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [430.013206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [430.013471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.013717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.013975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [430.014809] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.015085] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.044610] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.044870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [430.045067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [430.045254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [430.045488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.045674] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.045631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.045873] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [430.046003] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.046088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [430.046261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.046324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.046466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.046637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [430.046800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [430.046983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [430.047248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [430.047547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [430.047804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [430.048058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [430.048304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [430.049272] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.049593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.061423] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.094567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.094862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [430.095123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [430.095322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [430.095582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.095712] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.095780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.095974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [430.096060] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.096202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [430.096352] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.096427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.096610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.096788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [430.096991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [430.097210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [430.097485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [430.097739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [430.097997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.098286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.098565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [430.099663] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.099956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.111468] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.144550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026 <7> [430.144784] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025 <7> [430.144990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [430.145187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.145376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.145633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.145828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.145766] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.146011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [430.146110] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.146193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.146369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.146437] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.146651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.146884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [430.147190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [430.147486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [430.147747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [430.148005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [430.148261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [430.148972] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.149249] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.177881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [430.178141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [430.178361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.178651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.178763] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.178864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.179064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.179113] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.179271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [430.179442] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.179574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [430.179838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [430.180082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.180368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.180660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [430.181408] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.181684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.211213] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.211524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [430.211647] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.211752] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [430.211954] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [430.212033] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.212156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.212354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.212368] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.212619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.212820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.213017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.213190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [430.213364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [430.213599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [430.213793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [430.214180] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.214434] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [430.214630] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [430.214789] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [430.214942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.215097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.215255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.215447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.215621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.215789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [430.215942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [430.216092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [430.216281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [430.216591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [430.216853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [430.217110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [430.217358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [430.217705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [430.218553] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.218820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.228006] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.261214] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.261520] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [430.261742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [430.261815] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.261942] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [430.262135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.262160] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.262323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.262473] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.262555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.262744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.262925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.263100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.263275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.263480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.263683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [430.264057] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.264279] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [430.264503] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [430.264677] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [430.264845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.265055] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.265248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.265464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.265638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.265808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.265988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.266168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.266359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [430.266714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [430.267033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [430.267348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.267718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.268071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [430.269094] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.269424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.277979] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.311198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [430.311488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [430.311615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.311708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [430.311916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.311982] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.312108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.312275] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.312295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.312564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.312747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [430.312920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.313088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.313252] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.313473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [430.313939] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [430.314118] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [430.314288] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [430.314495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.314666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.314861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.315041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.315218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [430.315410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.315582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.315753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.315927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [430.316196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [430.316490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [430.316792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [430.317035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [430.317277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [430.317993] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.318264] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.344566] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [430.344820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [430.345024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.345214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.345443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.345630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.345582] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.345876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [430.345933] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.346142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [430.346211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.346414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [430.346664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.346984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.347279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [430.348043] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.348305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.377815] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.378072] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [430.378259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [430.378480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [430.378657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.378623] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.378826] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.379005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.378974] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.379167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.379275] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.379326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.379535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [430.379695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [430.379846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [430.380016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [430.380263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [430.380537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [430.380785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [430.381025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [430.381260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [430.382178] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.382462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.394583] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.427793] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.428039] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [430.428221] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [430.428445] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [430.428622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.428576] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.428793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.428917] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.428967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.429156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.429200] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.429307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.429507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.429659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.429808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.429983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [430.430231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [430.430507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [430.430752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.430990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.431275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [430.432242] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.432535] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.444612] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.477951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [430.478137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [430.478305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [430.478530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.478695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.478664] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.478857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [430.478997] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.479059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [430.479242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [430.479298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.479436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.479603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.479770] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.479954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [430.480210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [430.480487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [430.480733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [430.480979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [430.481240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [430.481929] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.482184] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.511159] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [430.511377] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [430.511555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.511513] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.511729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.511899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [430.511859] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.512098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [430.512157] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.512301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [430.512599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [430.512853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [430.513132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.513402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.513643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [430.514384] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.514632] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.544460] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.544677] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [430.544853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [430.545027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [430.545195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.545392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.545575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [430.545523] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.545778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [430.545866] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.545957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.546152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.546160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.546334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [430.546547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [430.546733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [430.546977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [430.547216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [430.547484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [430.547726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [430.547974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [430.548927] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.549181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.561337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.594452] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.594725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [430.594956] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [430.595157] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [430.595378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.595570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.595504] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.595754] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [430.595848] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.595968] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [430.596161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.596135] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.596324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [430.596545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [430.596709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [430.596899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [430.597160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [430.597423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [430.597714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.597951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.598185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [430.599142] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.599416] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.611326] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.644468] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691 <7> [430.644689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360 <7> [430.644881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [430.645065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.645244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.645472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.645583] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.645651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.645836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.645908] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.646024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.646191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.646181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.646377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.646543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [430.646703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.646864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.647025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.647220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [430.647626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691 <7> [430.647797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360 <7> [430.647958] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [430.648117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.648305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.648531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.648688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.648840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.648990] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.649138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.649283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.649475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [430.649646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.649798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.649948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.650111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [430.650427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [430.650686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [430.650966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.651223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.651544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [430.652345] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.652619] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.694522] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [430.694802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [430.695013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.695205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.695442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.695555] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.695627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.695877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [430.695904] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.696184] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.696257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [430.696476] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [430.696643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.696802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.696961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.697147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.697361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [430.697622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [430.697869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [430.698113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.698365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.698619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [430.699249] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.699535] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.728473] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.728677] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:473] <7> [430.728844] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.729132] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.748305] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.748676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [430.748899] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [430.749110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [430.749319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.749740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.749943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.750182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.750647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.750833] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [430.751032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [430.751231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [430.751549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [430.751939] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.752153] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [430.752334] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [430.752501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [430.752664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.752827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.753022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.753211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.753430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.753586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [430.753740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [430.753894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [430.754064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [430.754318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [430.754770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [430.755000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [430.755224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [430.755540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [430.756247] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.756479] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.761301] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.794472] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.794784] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [430.795054] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [430.795260] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [430.795532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.795655] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.795733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.795929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.796030] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.796145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.796349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.796373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.796535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.796719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.796902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.797135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [430.797694] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.797932] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [430.798121] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [430.798306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [430.798550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.798741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.798975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.799191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.799437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.799623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.799809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.800014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.800216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [430.800527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [430.800812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [430.801096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [430.801361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [430.801669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [430.802582] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.802867] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.811221] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.844547] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [430.844846] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [430.845100] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [430.845392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.845515] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.845634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.845872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.845945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.846126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.846371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [430.846590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.846735] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.846810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.847020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [430.847271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [430.847660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [430.847998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [430.848353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.848740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [430.849074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [430.849943] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.850262] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.877800] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [430.878082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [430.878360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.878490] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.878593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.878815] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.878887] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.879062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.879206] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.879341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [430.879654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [430.879929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [430.880182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.880462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [430.880715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [430.881514] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.881790] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.911106] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.911423] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [430.911528] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.911694] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [430.911891] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [430.911913] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.912078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.912260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.912230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.912502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.912682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.912848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.913012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [430.913179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [430.913417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [430.913624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [430.913878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [430.914128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [430.914387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [430.914630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [430.914876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [430.915933] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.916192] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.927902] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.961090] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [430.961395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [430.961496] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [430.961606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [430.961798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [430.961837] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [430.961978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.962111] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [430.962153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [430.962350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [430.962528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [430.962734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [430.962926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [430.963097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [430.963294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [430.963541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [430.963850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [430.964106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [430.964371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [430.964615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [430.964854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [430.965834] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [430.966092] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [430.977927] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.011212] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [431.011478] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [431.011605] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.011672] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [431.011859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.011939] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.012050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.012237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [431.012237] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.012525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [431.012728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [431.012919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.013094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.013271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.013532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [431.013817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [431.014081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [431.014359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [431.014623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [431.014883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [431.015637] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.015921] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.044450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [431.044646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [431.044827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.045004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.045179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [431.045444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [431.045459] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.045653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [431.045803] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.045922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [431.046114] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.046196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [431.046498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [431.046770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [431.047076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [431.047910] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.048223] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.077728] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.077985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [431.078210] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [431.078458] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [431.078653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.078607] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.078843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.078967] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.079033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [431.079206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [431.079257] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.079408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.079576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.079741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [431.079889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [431.080064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [431.080320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [431.080565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [431.080805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.081082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.081348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [431.082265] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.082574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.094539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.127780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.128053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [431.128252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [431.128514] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [431.128707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.128647] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.128896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.129025] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.129086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [431.129281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [431.129344] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.129507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.129673] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.129860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [431.130030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [431.130223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [431.130621] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.130853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [431.131021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [431.131186] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [431.131382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.131579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.131763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [431.131940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [431.132094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.132246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.132456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [431.132611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [431.132766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [431.133003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [431.133239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [431.133505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [431.133744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [431.134067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [431.135064] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.135353] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.144659] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.177795] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691 <7> [431.178052] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360 <7> [431.178274] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0 <7> [431.178562] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.178694] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.178773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.178986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.179053] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.179210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.179378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.179484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [431.179672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.179861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.180024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.180213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [431.180632] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691 <7> [431.180811] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360 <7> [431.180989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0 <7> [431.181161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.181386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.181558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.181724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.181888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [431.182049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.182209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.182408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.182580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [431.182837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [431.183076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [431.183324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [431.183609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [431.183840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [431.184508] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.184762] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.211069] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [431.211347] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [431.211560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.211503] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.211755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [431.211844] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.211931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [431.212120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [431.212113] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.212331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [431.212693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [431.212873] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [431.213047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.213216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [431.213429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [431.213608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [431.213782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [431.214139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [431.214346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [431.214498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.214649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [431.214807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [431.214995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [431.215191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [431.215492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [431.215761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [431.216025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [431.216273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [431.216559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [431.217253] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.217539] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.244458] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.244813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [431.245057] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [431.245327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [431.245548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.245468] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.245761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.245870] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.245988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.246263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.246242] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.246549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.246767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [431.246970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [431.247162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [431.247435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [431.248002] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.248258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [431.248513] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [431.248712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [431.248919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.249098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.249295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.249491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.249691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.249876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [431.250060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [431.250226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [431.250456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [431.250738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [431.251011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [431.251265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.251550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.251836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [431.252659] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.252905] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.261092] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.294386] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.294706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [431.294963] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [431.295164] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [431.295400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.295587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [431.295546] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.295775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [431.295896] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.295983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [431.296172] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.296175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.296422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.296614] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.296792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.296998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [431.297269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [431.297578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [431.297913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [431.298185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [431.298534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [431.299445] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.299743] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.311215] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.344427] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [431.344709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [431.344945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [431.345170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.345450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.345575] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.345671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.345894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.345985] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.346104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [431.346333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.346355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.346537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.346755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.346997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [431.347329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [431.347687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [431.348011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [431.348344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [431.348694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [431.349494] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.349808] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.377747] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [431.378063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [431.378395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.378534] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.378642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [431.378875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [431.378979] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.379140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [431.379361] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.379424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [431.379746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [431.380078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [431.380412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [431.380770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [431.381070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [431.382007] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.382356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.411047] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.411426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [431.411475] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.411644] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [431.411835] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [431.411864] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.412018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.412218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.412182] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.412465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.412645] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.412818] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.412986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [431.413158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [431.413384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [431.413599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [431.413885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [431.414177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [431.414501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.414853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.415155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [431.416295] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.416611] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.427945] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.461006] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.461366] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [431.461460] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.461596] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [431.461799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [431.461823] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.461994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.462137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.462186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [431.462427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [431.462618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [431.462845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.463029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.463203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.463453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.463665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [431.463937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [431.464206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [431.464496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [431.464812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [431.465086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [431.466170] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.466485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.477931] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.511175] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [431.511496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [431.511617] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.511721] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [431.511916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.511971] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.512105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.512330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [431.512314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.512533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [431.512755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [431.512929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.513105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.513299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.513508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [431.513791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [431.514085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [431.514403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [431.514685] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [431.514968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [431.515831] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.516116] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.544378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [431.544636] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [431.544844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.545035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.545219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [431.545530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [431.545660] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.545764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [431.546013] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.546048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [431.546329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [431.546335] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.546600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [431.546866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [431.547130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [431.547978] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.548244] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.577652] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.577922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [431.578146] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [431.578388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [431.578565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.578538] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.578739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.578883] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.578940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [431.579107] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [431.579160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.579296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.579449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.579604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [431.579757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [431.579937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [431.580361] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.580611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [431.580777] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [431.580946] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [431.581094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.581239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.581456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [431.581629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [431.581778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.581926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.582075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [431.582225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [431.582453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [431.582727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [431.582993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [431.583261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.583526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.583768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [431.584787] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.585081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.594533] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.627681] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.627978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [431.628218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [431.628497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [431.628693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.628640] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.628879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.628982] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.629079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [431.629318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [431.629298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.629507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.629683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.629881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [431.630059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [431.630278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [431.630690] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.630922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [431.631111] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [431.631320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [431.631493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.631662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.631840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [431.632037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [431.632195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.632410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.632572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [431.632727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [431.632895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [431.633206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [431.633518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [431.633823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [431.634091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [431.634366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [431.635414] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.635706] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.644486] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [431.677606] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.677898] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597 <7> [431.678108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293 <7> [431.678359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161 <7> [431.678554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.678496] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.678742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.678848] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.678925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.679114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.679137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.679314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.679491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.679702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.679919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.680093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.680285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.680467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [431.680642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [431.680855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [431.681308] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.681530] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597 <7> [431.681698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293 <7> [431.681868] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161 <7> [431.682046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.682259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.682427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.682586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.682748] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.682921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.683086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.683277] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.683438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.683593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [431.683749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [431.683906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [431.684077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [431.684374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [431.684645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [431.684935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [431.685194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [431.685480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [431.686493] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.686755] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.694012] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A] <7> [431.694531] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [431.694666] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [431.711374] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.744282] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.744541] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [431.744725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [431.744904] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [431.745087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.745320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [431.745505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [431.745448] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.745724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [431.745799] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.745966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [431.746103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.746265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [431.746542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [431.746827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.747084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.747421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [431.748168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.748937] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.794418] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.794773] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [431.795113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [431.795432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [431.795669] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [431.795590] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.795896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [431.796022] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.796120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.796432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.796444] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.796668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.796882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.797076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.797296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [431.797503] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [431.797713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [431.797959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [431.798314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [431.798658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [431.798981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [431.799304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [431.799644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [431.800940] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.801293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.810682] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [431.828198] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.828513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [431.860946] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.861188] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [431.861504] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [431.861619] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.861742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [431.861943] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [431.861980] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.862142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [431.862380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.862335] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.862579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [431.862782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [431.863016] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [431.863207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.863462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.863664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.863902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.864158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [431.864535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [431.864893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [431.865179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [431.865500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [431.865844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [431.867069] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.867409] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.877955] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.878156] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [431.910960] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.911306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [431.911380] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.911589] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [431.911810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [431.911782] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.912021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [431.912126] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.912265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.912478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [431.912686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [431.912938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [431.913135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [431.913372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.913570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.913766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [431.914007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [431.914357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [431.914663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [431.914974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [431.915301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [431.915639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [431.916815] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.917118] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [431.917817] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [431.918075] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [431.927876] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.961004] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [431.961401] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [431.961498] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [431.961666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [431.961915] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [431.961928] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [431.962157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [431.962344] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [431.962447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [431.962687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [431.962923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [431.963176] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [431.963551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [431.963929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [431.964260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.964616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [431.964933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [431.965846] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [431.966181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.011082] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.011482] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.011819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [432.012106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [432.012408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [432.012636] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [432.012568] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.012857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.013073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.013006] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.013324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.013427] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.013572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.013779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.013984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [432.014188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [432.014458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [432.014698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [432.015033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [432.015397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [432.015784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [432.016126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [432.016493] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [432.017986] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.018380] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.027295] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [432.044923] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.045267] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.077696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.077957] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.078252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [432.078397] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.078489] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [432.078677] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [432.078749] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.078862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [432.079033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.079033] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.079226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [432.079410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [432.079585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [432.079753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.079925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.080097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.080302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.080520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [432.080810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [432.081098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [432.081412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [432.081750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [432.082080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [432.083346] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.083649] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.094656] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.094869] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.127922] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.128272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [432.128383] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.128543] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [432.128749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [432.128756] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.128937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [432.129060] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.129123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.129397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.129590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [432.129766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [432.129955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [432.130121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.130332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.130512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.130762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [432.131059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [432.131371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [432.131640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [432.131944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [432.132226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [432.133229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.133511] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.134223] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [432.134467] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [432.144563] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.177550] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.177872] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [432.178132] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [432.178418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [432.178628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.178566] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.178830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.178925] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.179026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [432.179283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [432.179257] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.179546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [432.180043] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.180303] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [432.180515] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [432.180693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [432.180881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.181090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.181311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [432.181473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [432.181674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [432.181947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [432.182223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [432.182492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [432.182776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [432.183033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [432.183881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.184171] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.227663] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.228023] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.228438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [432.228538] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.228691] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [432.228949] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [432.228998] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.229213] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [432.229459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.229460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.229704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.229941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [432.230208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [432.230439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.230660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.230885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [432.231109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [432.231443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [432.232106] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.232428] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.232701] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [432.232916] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [432.233123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [432.233395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [432.233616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.233834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.234037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [432.234260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [432.234465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.234654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.234871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [432.235086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [432.235373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [432.235726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [432.236045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [432.236405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [432.236728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [432.237047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [432.238432] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.238723] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.243934] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [432.261596] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.261880] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.294306] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.294604] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.294907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [432.295163] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [432.295490] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [432.295620] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.295721] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [432.295944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.296038] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.296149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.296417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [432.296435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.296679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [432.296914] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.297116] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.297371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [432.297574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [432.297816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [432.298142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [432.298500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [432.298841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [432.299136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [432.299504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [432.300881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.301226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.311265] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.311457] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.344277] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.344618] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597 <7> [432.344906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293 <7> [432.345123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161 <7> [432.345413] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [432.345456] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.345627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.345827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.346023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.345965] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.346264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.346458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [432.346396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.346643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.346826] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.347016] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.347228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [432.347507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [432.347788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [432.348061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [432.348348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [432.348660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [432.349708] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.350034] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.350937] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [432.351228] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [432.361169] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.394230] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.394533] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [432.394742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [432.394934] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [432.395113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.395347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [432.395370] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.395522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [432.395724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [432.395719] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.395927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [432.396033] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.396222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [432.396497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [432.396757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [432.397001] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [432.397273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [432.397951] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.398249] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.444306] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.444609] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.444874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [432.445058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [432.445293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [432.445315] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.445466] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [432.445652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.445646] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.445816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.445989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.445953] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.446161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.446384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.446550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [432.446713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [432.446894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [432.447095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [432.447381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [432.447631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [432.447886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [432.448149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [432.448515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [432.449524] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.449792] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.460560] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [432.478020] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.478369] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.510867] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.511155] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.511490] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [432.511480] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.511712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [432.511911] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [432.511871] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.512107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [432.512261] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.512362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.512553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [432.512745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [432.512974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [432.513207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.513410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.513597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.513779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.513994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [432.514330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [432.514613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [432.514886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [432.515153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [432.515525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [432.516627] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.516922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.527805] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.528001] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.560970] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.561341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [432.561426] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.561579] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [432.561802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [432.561832] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.562006] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [432.562233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.562211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.562437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.562659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.562883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.563100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [432.563336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.563530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.563706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.563902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [432.564171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [432.564442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [432.564726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [432.565003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [432.565344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [432.566362] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.566675] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.567310] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [432.567577] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [432.577983] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.610910] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.611264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [432.611334] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.611527] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [432.611743] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [432.611752] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.611960] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.612088] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.612213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [432.612430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [432.612661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [432.612926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [432.613421] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.613698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [432.613909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [432.614107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [432.614380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.614631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [432.614858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [432.615090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [432.615374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [432.615710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [432.616011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [432.616331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [432.616681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [432.616997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [432.617799] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.618099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.660909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.661379] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.661509] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.661779] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.661800] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.662089] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [432.662093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.662362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [432.662561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [432.662750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [432.662983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.663192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.663377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.663550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.663731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.663940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [432.664119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [432.664363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [432.664545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [432.664819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [432.665115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [432.665446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [432.665758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [432.666030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [432.667309] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.667632] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.677203] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [432.694674] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.694973] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.727437] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.727682] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.727912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [432.728204] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [432.728395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [432.728346] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.728583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [432.728700] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.728768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.728956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [432.729017] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.729209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [432.729417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [432.729644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.729850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.730040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.730269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.730478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [432.731003] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.731279] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.731501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [432.731727] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [432.731904] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [432.732080] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [432.732344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.732539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [432.732749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [432.732908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [432.733074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.733329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.733488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.733643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.733826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [432.734129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [432.734452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [432.734757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [432.735033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [432.735298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [432.736376] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.736664] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.744567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.744762] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.777719] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.778069] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [432.778437] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [432.778561] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.778688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [432.778942] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [432.779000] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.779212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.779434] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.779518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.779762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [432.780019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [432.780265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [432.780470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.780668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.780892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.781186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [432.781544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [432.781882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [432.782234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [432.782546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [432.782882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [432.784157] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.784501] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.785300] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [432.785582] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [432.794461] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.827477] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.827833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [432.828129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [432.828469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [432.828612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.828715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.828952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.829045] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.829240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [432.829535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [432.829473] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.829801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [432.830164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [432.830514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [432.830877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [432.831248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [432.831647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [432.832598] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.832952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.877631] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.878026] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.878538] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [432.878631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.878871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [432.879151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [432.879182] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.879400] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [432.879574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.879651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.879890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.880179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [432.880419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [432.880654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.880874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.881182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [432.881437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [432.881719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [432.882098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [432.882521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [432.882939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [432.883380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [432.883744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [432.885325] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.885743] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.893818] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [432.911586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.911946] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.944139] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.944418] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.944679] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [432.944901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [432.945090] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [432.945343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [432.945524] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.945487] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.945710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.945848] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.945893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [432.946106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [432.946181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.946350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.946561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [432.946749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [432.946945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [432.947155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [432.947438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [432.947732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [432.948015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [432.948328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [432.948595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [432.949789] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [432.950094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [432.961143] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.961354] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [432.994192] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [432.994582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823 <7> [432.994881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614 <7> [432.995280] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614 <7> [432.995342] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [432.995611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [432.995866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.995820] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [432.996184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [432.996306] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [432.996438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [432.996686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [432.996927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.997244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.997495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.997755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.998032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [432.998388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [432.998643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [432.998898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [432.999141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [432.999364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.999614] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [432.999893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.000354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [433.000773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [433.001262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [433.001629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [433.001985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [433.002373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [433.003695] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.004061] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.004995] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [433.005335] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [433.011035] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.044177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.044554] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [433.044816] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [433.045061] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [433.045419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.045536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.045720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [433.045965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [433.045985] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.046243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [433.046405] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.046549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [433.047056] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.047387] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [433.047623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [433.047864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [433.048140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.048426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [433.048664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [433.048910] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [433.049149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [433.049470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [433.049789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [433.050132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [433.050449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [433.050762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [433.051649] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.051999] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.094358] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.094890] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.095296] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.095421] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.095646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [433.095947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [433.095899] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.096241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [433.096357] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.096496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [433.096794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.097054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.097371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.097599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.097877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.098689] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [433.098949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [433.099251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [433.099582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [433.099952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [433.100390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [433.100771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [433.101231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [433.101631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [433.103101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.103548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.110440] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [433.128240] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.128556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.160968] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.161308] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.161446] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.161594] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [433.161861] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [433.161841] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.162068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [433.162240] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.162320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [433.162510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.162732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [433.162915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [433.163163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [433.163356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.163548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.163726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.163906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.164153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [433.164488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [433.164806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [433.165130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [433.165473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [433.165764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [433.166960] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.167339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.177757] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.177978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.210753] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.211071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823 <7> [433.211419] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614 <7> [433.211633] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614 <7> [433.211565] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.211836] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [433.211943] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.212042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.212287] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.212304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.212531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.212738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.212966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [433.213200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.213435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.213667] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.213928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [433.214514] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.214779] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823 <7> [433.215010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614 <7> [433.215242] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614 <7> [433.215427] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [433.215672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.215887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.216124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.216337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.216509] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [433.216670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.216834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.216996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.217227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [433.217522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [433.217817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [433.218084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [433.218454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [433.218734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [433.219760] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.220053] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.220776] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [433.221031] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [433.227622] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.260779] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.261167] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [433.261280] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.261432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [433.261668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [433.261698] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.261890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.262064] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.262155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [433.262392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [433.262693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [433.262942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [433.263301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [433.263628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [433.263951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [433.264304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [433.264625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [433.265552] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.265906] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.310777] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.311130] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.311268] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.311430] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [433.311648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [433.311645] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.311853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [433.311959] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.312038] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [433.312292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.312470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.312649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.312821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.313013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.313257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [433.313430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [433.313596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [433.313788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [433.314054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [433.314355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [433.314654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [433.314934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [433.315247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [433.316623] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.316986] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.327107] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [433.344764] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.345133] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.377407] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.377697] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.377977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [433.378299] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [433.378522] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [433.378451] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.378740] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [433.378850] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.378937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.379173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [433.379202] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.379370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [433.379573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [433.379785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.380004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.380240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.380467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.380749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [433.381112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [433.381431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [433.381732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [433.382033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [433.382351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [433.383488] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.383802] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.394386] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.394591] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.427565] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.427874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826 <7> [433.428076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605 <7> [433.428343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620 <7> [433.428536] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [433.428481] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.428728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.428850] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.428913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [433.429122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [433.429171] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.429305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [433.429529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [433.429728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.429928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.430168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.430381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [433.430658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [433.430935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [433.431233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [433.431502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [433.431780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [433.432833] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.433137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.433763] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [433.434045] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [433.444371] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.477389] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.477714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [433.477936] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289 <7> [433.478201] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164 <7> [433.478218] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.478420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.478622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [433.478648] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.478849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [433.479001] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.479062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [433.479377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [433.479682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [433.479997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [433.480350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [433.480673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [433.480985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [433.481910] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.482287] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.527523] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.527960] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.528482] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913 <7> [433.528563] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.528815] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452 <7> [433.529106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794 <7> [433.529042] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.529357] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892 <7> [433.529532] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.529604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.529843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [433.530100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [433.530394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [433.530652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.530879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [433.531129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [433.531358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [433.531636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [433.532029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [433.532457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [433.532881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [433.533293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [433.533662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [433.535299] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.535675] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.543715] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [433.561686] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.562059] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.594229] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.594538] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.594848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691 <7> [433.595205] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676 <7> [433.595443] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350 <7> [433.595364] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.595696] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334 <7> [433.595801] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.595922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.596243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [433.596226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.596469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [433.596699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [433.596922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.597183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [433.597439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [433.597683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [433.597975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [433.598361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [433.598700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [433.599029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [433.599428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [433.599814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [433.601136] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.601480] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.611096] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.611299] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.644261] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.644622] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 691) -> ( 0 - 823), size 691 -> 823 <7> [433.644879] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 691 - 1367) -> ( 823 - 2437), size 676 -> 1614 <7> [433.645186] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2717) -> (2437 - 4051), size 1350 -> 1614 <7> [433.645336] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.645433] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0 <7> [433.645677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.645767] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.645905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.646180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.646196] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.646478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.646726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [433.646943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.647202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.647488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.647801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [433.648193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [433.648539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [433.648875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [433.649227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [433.649617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [433.650858] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.651285] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.652197] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [433.652492] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [433.660923] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.694030] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.694428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [433.694673] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [433.694896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [433.695168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.695394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [433.695320] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.695631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [433.695721] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.695894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [433.696115] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.696214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [433.696544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [433.696858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [433.697227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [433.697541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [433.697854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [433.698678] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.699012] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.744079] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.744446] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.744834] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [433.745170] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [433.745405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [433.745331] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.745635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [433.745772] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.745886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.746193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.746213] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.746439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.746659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.746875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.747103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [433.747313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [433.747530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [433.747789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [433.748169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [433.748529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [433.748876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [433.749222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [433.749576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [433.750762] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.751138] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.760323] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [433.778083] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.778412] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.810614] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.810895] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.811207] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [433.811321] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.811473] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [433.811680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [433.811708] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.811864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [433.812065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.812009] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.812249] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [433.812443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [433.812679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [433.812880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.813094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.813258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.813416] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.813610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [433.813898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [433.814233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [433.814502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [433.814765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [433.815018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [433.816118] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.816419] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.827556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.827767] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.860608] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.860884] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823 <7> [433.861162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614 <7> [433.861350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614 <7> [433.861328] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.861553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [433.861664] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.861728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.861900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.861955] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.862129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.862320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.862582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [433.862760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.862930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.863135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [433.863347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [433.863636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [433.863928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [433.864236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [433.864509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [433.864823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [433.865908] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.866253] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.866869] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [433.867162] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [433.877624] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.910656] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.911010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [433.911366] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [433.911513] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.911602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [433.911843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.911923] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.912086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [433.912313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [433.912307] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.912583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [433.912877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [433.913256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [433.913589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [433.913947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [433.914305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [433.914628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [433.915556] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.915922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.960621] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.960907] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [433.961277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [433.961329] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [433.961503] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [433.961712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [433.961698] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [433.961907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [433.962028] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [433.962135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.962328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [433.962571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [433.962761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [433.962951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [433.963186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [433.963405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [433.963616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [433.963968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [433.964375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [433.964701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [433.965005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [433.965365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [433.965693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [433.967050] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [433.967383] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [433.976999] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [433.994572] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [433.994868] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [434.027270] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.027531] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [434.027787] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [434.028105] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [434.028245] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.028332] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [434.028552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [434.028650] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.028775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.029012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [434.029000] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.029262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [434.029460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [434.029656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.029849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.030086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.030303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.030551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [434.030838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [434.031121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [434.031366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [434.031608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [434.031875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [434.033061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.033348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.044352] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.044560] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [434.077647] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.077963] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826 <7> [434.078259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605 <7> [434.078401] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.078472] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620 <7> [434.078693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0 <7> [434.078775] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.078882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.079094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.079107] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.079289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [434.079502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [434.079678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [434.079842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.080004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.080232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.080453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [434.080750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [434.081042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [434.081338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [434.081598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [434.081907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [434.083003] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.083388] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.084181] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [434.084452] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [434.094277] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.127284] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.127629] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [434.127932] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289 <7> [434.128233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164 <7> [434.128374] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.128465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.128686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.128778] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.128932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [434.129187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [434.129162] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.129442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [434.130070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.130347] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598 <7> [434.130597] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289 <7> [434.130828] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164 <7> [434.131072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.131288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.131486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [434.131728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [434.131952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [434.132321] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [434.132648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [434.132942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [434.133279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [434.133552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [434.134456] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.134794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.177415] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.177784] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [434.178151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913 <7> [434.178251] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.178382] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452 <7> [434.178606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794 <7> [434.178664] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.178813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892 <7> [434.179033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.179032] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.179259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.179477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [434.179677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [434.179872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.180093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.180303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [434.180519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [434.180794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [434.181343] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.181591] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [434.181854] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913 <7> [434.182095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452 <7> [434.182311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794 <7> [434.182509] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892 <7> [434.182703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.182908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.183143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [434.183349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [434.183575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.183787] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.184034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [434.184228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [434.184418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [434.184721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [434.185048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [434.185332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [434.185621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [434.185893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [434.187127] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.187426] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.193614] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [434.211192] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.211473] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [434.243939] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.244291] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [434.244595] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691 <7> [434.244894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676 <7> [434.245305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350 <7> [434.245352] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.245547] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334 <7> [434.245794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.245785] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.246048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.246205] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.246283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [434.246535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [434.246769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.246988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.247282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [434.247514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [434.247842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [434.248376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [434.248731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [434.249121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [434.249428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [434.249735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [434.251072] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.251410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.260862] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [434.261069] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [434.294048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 691) -> ( 0 - 2018), size 691 -> 2018 <7> [434.294180] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.294316] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 691 - 1367) -> (2018 - 4051), size 676 -> 2033 <7> [434.294500] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2717) -> ( 0 - 0), size 1350 -> 0 <7> [434.294512] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.294676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0 <7> [434.294792] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.294853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.295068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.295275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [434.295513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [434.295707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.295896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.296143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.296364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.296599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [434.296813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.296990] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.297222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.297395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [434.297564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.297758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.297947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.298221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [434.298490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [434.298750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [434.299021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [434.299295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [434.299563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [434.300439] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.300754] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.301549] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [434.301821] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A] <7> [434.327345] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [434.327697] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [434.327959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.328297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [434.328444] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.328542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [434.328797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [434.328886] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.329086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [434.329314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.329433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [434.329748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [434.330072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [434.330431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [434.330727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [434.331510] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.331805] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.360617] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.361056] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [434.361188] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.361323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [434.361555] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [434.361599] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.361770] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.361952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.361993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.362322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.362559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.362781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.362991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [434.363274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [434.363501] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [434.363774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [434.364165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [434.364543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [434.364877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [434.365351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [434.365672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [434.366798] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.367194] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.377565] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.410523] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.410875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [434.411278] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [434.411410] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.411554] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [434.411780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.411821] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.412017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [434.412233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [434.412204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.412493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [434.412736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.412963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.413264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.413475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.413726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [434.414090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [434.414420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [434.414732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [434.415091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [434.415408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [434.416411] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.416754] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.427687] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.460616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2018), size 1606 -> 2018 <7> [434.460962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2018 - 4051), size 826 -> 2033 <7> [434.461345] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0 <7> [434.461475] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.461629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.461872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.461921] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.462179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.462348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.462449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.462713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [434.462941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.463247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.463522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.463792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [434.464193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [434.464548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [434.464880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [434.465240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [434.465634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [434.466592] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.466959] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.493974] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [434.494405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [434.494487] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.494648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.494880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [434.494889] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.495151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [434.495273] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.495382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [434.495680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [434.496068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [434.496389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [434.496697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [434.497002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [434.497354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [434.498340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.498682] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.527231] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.527548] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [434.527764] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [434.527949] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [434.528191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.528362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.528342] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.528536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.528681] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.528739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.528934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.529028] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.529157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [434.529336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [434.529525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [434.529729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [434.530120] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.530360] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [434.530552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [434.530732] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [434.530931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.531173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.531353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.531536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.531714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.531871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [434.532065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [434.532222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [434.532388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [434.532674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [434.532959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [434.533252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [434.533537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [434.533784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [434.534899] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.535217] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.544084] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.577245] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.577550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [434.577760] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [434.577960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [434.578344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.578388] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.578584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [434.578780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [434.578749] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.578967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [434.579075] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.579305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.579502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.579706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.579919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.580186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [434.580616] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.580863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [434.581134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [434.581334] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [434.581528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.581702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [434.581884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [434.582140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [434.582366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.582553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.582724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.582885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.583102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [434.583366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [434.583625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [434.583880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [434.584164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [434.584438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [434.585460] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.585772] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.594021] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.627488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2026), size 1606 -> 2026 <7> [434.627782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2026 - 4051), size 826 -> 2025 <7> [434.628093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0 <7> [434.628200] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.628350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.628602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.628634] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.628838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [434.629031] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.629131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [434.629350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [434.629572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.629797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.630054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.630297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [434.630843] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2026), size 1606 -> 2026 <7> [434.631129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2026 - 4051), size 826 -> 2025 <7> [434.631409] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0 <7> [434.631626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.631834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.632082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [434.632290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [434.632487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [434.632704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.632908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.633167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.633364] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [434.633675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [434.634009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [434.634369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [434.634684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [434.635012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [434.636041] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.636352] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.660503] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [434.660774] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [434.661060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.661139] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.661250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.661438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [434.661471] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.661651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [434.661748] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.661884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [434.662199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [434.662479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [434.662757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [434.663044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [434.663293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [434.664127] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.664402] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.693861] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.694265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2310), size 1354 -> 2310 <7> [434.694372] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.694526] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1354 - 4051) -> (2310 - 2894), size 2697 -> 584 <7> [434.694755] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2894 - 4051), size 0 -> 1157 <7> [434.694808] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.694998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.695221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.695227] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.695458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [434.695720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [434.695940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.696198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.696401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [434.696599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [434.696827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [434.697211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [434.697558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [434.697954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [434.698312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [434.698630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [434.699880] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.700288] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.710732] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.743824] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.744194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618 <7> [434.744235] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.744480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817 <7> [434.744611] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.744694] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616 <7> [434.744899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.744929] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.745159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.745361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [434.745624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [434.745822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.746037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [434.746223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [434.746398] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [434.746635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [434.746937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [434.747240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [434.747522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [434.747801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [434.748114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [434.749245] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.749563] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.760729] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.794023] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2018), size 1618 -> 2018 <7> [434.794017] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.794428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1618 - 2435) -> (2018 - 4051), size 817 -> 2033 <7> [434.794597] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.794778] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0 <7> [434.795169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.795145] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.795490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.795824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.796207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.796526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [434.796821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.797197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.797491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.797836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [434.798361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [434.798881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [434.799408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [434.799889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [434.800386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [434.801509] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.801945] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.827314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [434.827700] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [434.828054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.828174] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.828301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [434.828566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [434.828618] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.828791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [434.829015] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.829086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [434.829431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [434.829763] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [434.830131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [434.830465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [434.830829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [434.831765] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.832161] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.860517] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.860912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [434.861320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [434.861366] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.861573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [434.861834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.861793] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.862128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.862197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.862363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.862641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.862872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.863141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [434.863353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [434.863589] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [434.863842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [434.864281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [434.864652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [434.865018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [434.865378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [434.865723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [434.866812] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.867699] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.877576] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.910453] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.910791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [434.911137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [434.911179] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.911352] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [434.911557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.911655] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.911758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [434.911987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [434.912059] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.912221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [434.912463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.912700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.912889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.913119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.913339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [434.913638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [434.913925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [434.914260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [434.914544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [434.914824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [434.915727] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.916052] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.927475] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [434.960484] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2018), size 1606 -> 2018 <7> [434.960730] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2018 - 4051), size 826 -> 2033 <7> [434.960929] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0 <7> [434.961185] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.961202] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.961364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.961543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.961570] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.961755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.961974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [434.961915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.962152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.962333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.962515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.962721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [434.963152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2018), size 1606 -> 2018 <7> [434.963357] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2018 - 4051), size 826 -> 2033 <7> [434.963526] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0 <7> [434.963747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.963916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [434.964197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [434.964384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [434.964579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [434.964741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.964901] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.965119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [434.965292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [434.965561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [434.965829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [434.966118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [434.966394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [434.966650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [434.967399] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.967675] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [434.993882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [434.994284] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [434.994272] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [434.994530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.994677] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [434.994756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [434.995027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [434.995054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [434.995282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [434.995565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [434.996044] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351 <7> [434.996292] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700 <7> [434.996474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [434.996654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [434.996881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [434.997147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [434.997339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [434.997608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [434.997862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [434.998168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [434.998413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [434.998651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [434.999423] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [434.999673] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.027269] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.027630] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [435.027874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [435.028180] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [435.028315] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.028399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.028635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.028718] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.028866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.029094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.029176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.029395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.029625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [435.029817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [435.030045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [435.030280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [435.030748] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.031076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287 <7> [435.031337] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599 <7> [435.031566] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165 <7> [435.031776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.031972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.032156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.032333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.032548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.032752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [435.032992] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [435.033166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [435.033386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [435.033689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [435.034009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [435.034286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [435.034561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [435.034873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [435.035969] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.036276] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.043865] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.077098] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.077406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [435.077646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [435.077848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [435.078114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.078155] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.078325] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.078564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.078535] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.078794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.078856] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.079031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.079215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.079400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.079580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.079795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [435.080343] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.080623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606 <7> [435.080864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826 <7> [435.081112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619 <7> [435.081328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.081521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.081696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.081889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.082130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.082365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.082585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.082785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.082967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [435.083215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [435.083452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [435.083690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.084096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.084408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [435.085439] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.085752] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.093979] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.127318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2026), size 1606 -> 2026 <7> [435.127594] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2026 - 4051), size 826 -> 2025 <7> [435.127814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0 <7> [435.128098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.128324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.128248] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.128547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [435.128650] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.128808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [435.129062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [435.129015] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.129259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.129459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.129665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.129911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [435.130294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [435.130614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [435.130955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [435.131327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [435.131679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [435.132446] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.132782] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.160475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354 <7> [435.160792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697 <7> [435.161100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.161221] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.161334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.161579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [435.161622] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.161824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [435.162007] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.162160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [435.162489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [435.162800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [435.163142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [435.163514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [435.163878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [435.164876] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.165263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.193754] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.194101] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2310), size 1354 -> 2310 <7> [435.194189] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.194323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1354 - 4051) -> (2310 - 2894), size 2697 -> 584 <7> [435.194511] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2894 - 4051), size 0 -> 1157 <7> [435.194564] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.194692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.194870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.194891] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.195178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [435.195371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [435.195560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.195763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.195957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [435.196128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [435.196332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [435.196626] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [435.196940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [435.197228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [435.197504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [435.197826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [435.198992] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.199296] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.210596] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.243726] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.244137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618 <7> [435.244216] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.244411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817 <7> [435.244640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616 <7> [435.244617] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.244865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.245016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.245130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.245332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [435.245591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [435.245809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.246064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.246266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [435.246466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [435.246703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [435.247003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [435.247279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [435.247563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.247856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.248150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [435.249168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.249487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.260643] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.293819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2687), size 1618 -> 2687 <7> [435.294183] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1618 - 2435) -> (2687 - 4051), size 817 -> 1364 <7> [435.294294] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.294425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0 <7> [435.294655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.294693] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.294881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.295065] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.295148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [435.295370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [435.295612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.295838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.296065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.296241] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.296428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [435.296599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.296768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.296966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.297209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [435.297577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [435.297882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [435.298208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [435.298486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [435.298741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [435.299527] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.299827] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.343889] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [435.344254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [435.344490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.344704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.344959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.345153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.345104] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.345392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [435.345489] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.345689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [435.345815] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.345987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [435.346252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.346539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.346807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [435.347616] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.347954] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.377474] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:474] <7> [435.378059] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.378505] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.378849] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.407364] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.407823] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907 <7> [435.408104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392 <7> [435.408321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752 <7> [435.408523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.408719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.408927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.409121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.409309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.409493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [435.409682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [435.409866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [435.410122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [435.410458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [435.410771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [435.411070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [435.411350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [435.411629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [435.412869] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.413178] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.428426] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.460609] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.461107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [435.461061] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.461419] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [435.461707] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [435.461623] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.462019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.462122] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.462306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.462592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.462867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.463169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.463438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.463707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.463985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.464305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [435.465004] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.465327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [435.465576] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [435.465815] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [435.466064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.466303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.466542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.466778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.467032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.467272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.467509] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.467745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.468048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [435.468454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [435.468846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [435.469255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [435.469640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [435.470021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [435.471420] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.471776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.477530] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.510731] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687 <7> [435.511132] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.511191] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364 <7> [435.511491] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [435.511571] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.511775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.512071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.512024] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.512353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.512624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.512886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [435.513145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.513384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.513621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.513931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [435.514576] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687 <7> [435.514834] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364 <7> [435.515098] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [435.515337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.515573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.515812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.516065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.516303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [435.516539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.516777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.517034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.517293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [435.517701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [435.518132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [435.518489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [435.518841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [435.519209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [435.520441] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.520809] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.543933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [435.543948] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.544241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [435.544338] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.544501] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.544715] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.544775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.545085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.545361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.545663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [435.546291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [435.546533] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [435.546755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.546992] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.547214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.547415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.547630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [435.548123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [435.548325] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [435.548508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.548692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.548877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.549064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.549252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [435.549529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [435.549788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [435.550056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.550301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.550538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [435.551399] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.551639] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.577193] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.577577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907 <7> [435.577842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392 <7> [435.578181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752 <7> [435.578179] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.578459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.578636] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.578725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.578998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.579054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.579239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.579478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.579712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [435.579966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [435.580205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [435.580490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [435.581252] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.581567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907 <7> [435.581797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392 <7> [435.582052] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752 <7> [435.582270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.582481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.582683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.582883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.583101] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.583285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [435.583468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [435.583648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [435.583846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [435.584157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [435.584437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [435.584704] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [435.584969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [435.585223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [435.586370] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.586600] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.593819] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.627139] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.627532] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [435.627814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [435.628122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [435.628135] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.628378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.628515] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.628621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.628861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.628873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.629127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.629368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.629602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.629839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.630093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.630381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [435.630793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [435.631211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [435.631601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [435.632008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [435.632394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [435.634062] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.634424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.644061] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.677472] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697 <7> [435.677790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354 <7> [435.678099] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [435.678109] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.678362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.678482] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.678612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.678858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [435.678835] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.679102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [435.679327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [435.679544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.679759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.679994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.680254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [435.680631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [435.681016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [435.681377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [435.681735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [435.682105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [435.683277] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.683638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.710449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [435.710729] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [435.711029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.711032] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.711282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.711403] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.711527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [435.711766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [435.711755] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.712055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [435.712429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [435.712788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [435.713157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.713509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.713858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [435.715039] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.715404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.743763] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.744094] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.744139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936 <7> [435.744379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376 <7> [435.744434] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.744603] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739 <7> [435.744752] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.744822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.745099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.745330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [435.745551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [435.745769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.746002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.746222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [435.746437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [435.746692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [435.747078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [435.747442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [435.747799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [435.748177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [435.748499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [435.749974] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.750325] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.760757] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.793776] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.794151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.794195] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2936) -> ( 0 - 2306), size 2936 -> 2306 <7> [435.794471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2936 - 3312) -> (2306 - 2893), size 376 -> 587 <7> [435.794524] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.794724] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3312 - 4051) -> (2893 - 4051), size 739 -> 1158 <7> [435.794898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.794986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.795231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.795476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [435.795718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [435.795983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.796223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [435.796463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [435.796699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [435.796980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [435.797357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [435.797718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [435.798098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [435.798453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [435.798804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [435.800425] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.800793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.810839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.843797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2306) -> ( 0 - 2687), size 2306 -> 2687 <7> [435.844142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2306 - 2893) -> (2687 - 4051), size 587 -> 1364 <7> [435.844149] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.844408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2893 - 4051) -> ( 0 - 0), size 1158 -> 0 <7> [435.844518] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.844660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.844913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.844888] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.845144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.845363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.845582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [435.845798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.846040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.846259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [435.846522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [435.846921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [435.847282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [435.847634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [435.848002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [435.848352] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [435.849397] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.849758] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.877117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [435.877403] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [435.877638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.877905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.877915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.878137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.878251] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.878361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.878571] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.878622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [435.879015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [435.879377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [435.879728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.880097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [435.880444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [435.881480] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.881842] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.910481] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.910937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907 <7> [435.910917] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.911218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392 <7> [435.911299] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.911474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752 <7> [435.911650] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.911720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.911985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.912229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.912469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.912706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.912958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [435.913176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [435.913390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [435.913652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [435.914468] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.914764] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907 <7> [435.915096] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392 <7> [435.915319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752 <7> [435.915535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.915749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.915983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.916197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.916413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.916626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [435.916839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [435.917067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [435.917301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [435.917665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [435.918028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [435.918356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [435.918677] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [435.919017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [435.920249] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.920548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.927187] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.960581] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.961004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [435.961067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [435.961369] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [435.961417] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [435.961648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [435.961803] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [435.961951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.962224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.962494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.962758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.963050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.963314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.963577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.963837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.964163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [435.964837] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [435.965182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [435.965432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [435.965671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [435.965922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.966158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [435.966395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [435.966633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [435.966884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [435.967118] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [435.967354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [435.967588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [435.967839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [435.968262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [435.968651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [435.969022] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [435.969362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [435.969686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [435.970872] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [435.971161] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [435.977118] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [436.010479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687 <7> [436.010923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364 <7> [436.010922] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.011228] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [436.011328] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.011512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.011713] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.011793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.012065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.012312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.012553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [436.012791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.013063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.013301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.013593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [436.014380] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687 <7> [436.014642] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364 <7> [436.014908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [436.015146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.015382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.015620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.015887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.016126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [436.016358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.016593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.016830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.017254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [436.017623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [436.018091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [436.018448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [436.018804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [436.019175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [436.020326] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.020652] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.043808] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021 <7> [436.044148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030 <7> [436.044146] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.044405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.044517] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.044648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [436.044950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [436.044914] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.045194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [436.045479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [436.045899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [436.046262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [436.046614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [436.046986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [436.047329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [436.048401] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.048716] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.077141] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [436.077557] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907 <7> [436.077903] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.077966] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392 <7> [436.078215] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752 <7> [436.078272] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.078457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.078617] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.078698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.078966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.079209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.079447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.079683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [436.079940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [436.080179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [436.080461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [436.080882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [436.081282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [436.081673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [436.082074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [436.082457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [436.084064] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.084400] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.094062] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [436.127143] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [436.127627] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289 <7> [436.128002] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598 <7> [436.128015] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.128302] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164 <7> [436.128420] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.128580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.128805] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.128881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [436.129156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [436.129429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [436.129691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.129976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.130242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.130505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.130824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [436.131305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [436.131753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [436.132393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [436.132784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [436.133294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [436.135129] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.135537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.144019] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [436.177496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697 <7> [436.177912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354 <7> [436.177923] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.178224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0 <7> [436.178329] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.178506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.178712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.178781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.179104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [436.179379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [436.179647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [436.179931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.180200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.180465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.180784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [436.181278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [436.181721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [436.182131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [436.182517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [436.182920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [436.184165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.184557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.210411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026 <7> [436.210723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025 <7> [436.211054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.211027] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.211306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.211393] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.211551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [436.211789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [436.211739] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.212100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [436.212514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [436.212924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [436.213315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [436.213698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [436.214100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [436.215311] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.215672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.243739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [436.244182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936 <7> [436.244136] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.244460] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376 <7> [436.244718] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739 <7> [436.244642] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.244995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.245076] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.245244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.245489] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [436.245729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [436.245983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.246219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.246457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [436.246691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [436.246977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [436.247349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [436.247709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [436.248088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [436.248442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [436.248793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [436.250432] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.250794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.260768] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [436.293710] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [436.294182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2936) -> ( 0 - 2306), size 2936 -> 2306 <7> [436.294127] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.294466] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2936 - 3312) -> (2306 - 2893), size 376 -> 587 <7> [436.294635] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.294722] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3312 - 4051) -> (2893 - 4051), size 739 -> 1158 <7> [436.294998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.295072] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.295244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.295489] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [436.295731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [436.295998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.296246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.296485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [436.296723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [436.297009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [436.297385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [436.297745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [436.298113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [436.298469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [436.298840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [436.300479] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.300871] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.310860] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [436.343769] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.344252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2306) -> ( 0 - 583), size 2306 -> 583 <7> [436.344203] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.344539] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2306 - 2893) -> ( 583 - 2898), size 587 -> 2315 <7> [436.344704] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.344800] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2893 - 4051) -> (2898 - 4051), size 1158 -> 1153 <7> [436.345080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.345146] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.345337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.345586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [436.345847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [436.346088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.346323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.346561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.346800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.347041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.347255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.347470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 4, 8, 8, 8, 8, 8, 0, 0, 19, 4, 19 <7> [436.347685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [436.347972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [436.348531] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.348816] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2306) -> ( 0 - 583), size 2306 -> 583 <7> [436.349065] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2306 - 2893) -> ( 583 - 2898), size 587 -> 2315 <7> [436.349285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2893 - 4051) -> (2898 - 4051), size 1158 -> 1153 <7> [436.349501] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.349718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.349954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [436.350170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [436.350387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.350602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.350837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.351054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.351269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.351484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.351699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 4, 8, 8, 8, 8, 8, 0, 0, 19, 4, 19 <7> [436.351929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [436.352145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [436.352482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [436.352811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [436.353156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [436.353479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [436.353801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [436.355130] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.355424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.359990] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A] <7> [436.360392] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [436.360529] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [436.377640] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.410541] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.411046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [436.410994] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.411361] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939 <7> [436.411553] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.411648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737 <7> [436.411958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.412042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.412233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [436.412506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [436.412774] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [436.413091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [436.413704] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.414035] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [436.414289] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939 <7> [436.414528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737 <7> [436.414764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.415029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [436.415271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [436.415510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [436.415766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [436.416189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [436.416584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [436.416990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [436.417347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [436.417699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [436.418811] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.419190] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.460365] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.460873] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.461081] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.461414] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.461381] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.461769] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673 <7> [436.461791] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.462070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692 <7> [436.462326] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333 <7> [436.462572] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353 <7> [436.462841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.463085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.463328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.463572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.463836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.464076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [436.464318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [436.464560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [436.464875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [436.465291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [436.465687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [436.466089] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [436.466443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [436.466796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [436.468335] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.468703] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.476666] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [436.494415] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.494737] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.527042] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.527397] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.527746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452 <7> [436.528054] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913 <7> [436.528073] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.528314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893 <7> [436.528562] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793 <7> [436.528573] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.528842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.529016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.529091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [436.529337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [436.529577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [436.529836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.530071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.530307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.530545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.531425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [436.532191] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.532461] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.532736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452 <7> [436.532987] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913 <7> [436.533207] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893 <7> [436.533423] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793 <7> [436.533639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.533877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [436.534097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [436.534311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [436.534525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.534741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.534978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.535195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.535430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [436.535795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [436.536140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [436.536466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [436.536792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [436.537131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [436.538567] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.539048] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.544030] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.544214] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.577099] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.577528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 452) -> ( 0 - 583), size 452 -> 583 <7> [436.577877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 452 - 1365) -> ( 583 - 2898), size 913 -> 2315 <7> [436.577897] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.578166] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2258) -> (2898 - 4051), size 893 -> 1153 <7> [436.578441] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0 <7> [436.578459] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.578708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.578977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.578942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.579221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.579457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.579692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [436.579950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.580189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.580424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.580709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [436.581139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [436.581537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [436.581945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [436.582333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [436.582719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [436.584470] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.584834] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.585476] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [436.585734] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [436.594054] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.627008] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.627406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [436.627685] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939 <7> [436.627984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737 <7> [436.628004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.628239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.628486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [436.628512] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.628732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [436.628998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [436.628956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.629288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [436.629707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [436.630128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [436.630522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [436.630931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [436.631320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [436.632571] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.632968] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.677062] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.677438] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.677838] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673 <7> [436.677863] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.678109] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692 <7> [436.678359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333 <7> [436.678368] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.678601] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353 <7> [436.678785] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.678864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.679104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.679345] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.679583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.679842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.680081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [436.680320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [436.680555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [436.680861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [436.681276] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [436.681678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [436.682071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [436.682427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [436.682785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [436.684592] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.684973] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.693205] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [436.711060] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.711384] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.743715] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.744180] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.744194] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.744583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452 <7> [436.744758] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.744939] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913 <7> [436.745201] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893 <7> [436.745210] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.745450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793 <7> [436.745693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.745955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [436.746201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [436.746443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [436.746681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.746935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [436.747177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [436.747416] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [436.747709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [436.748358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [436.748757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [436.749312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [436.749696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [436.750067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [436.751875] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.752245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.760888] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.761148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.793833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.793985] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.794391] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 452) -> ( 0 - 585), size 452 -> 585 <7> [436.794364] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.794681] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 452 - 1365) -> ( 585 - 2894), size 913 -> 2309 <7> [436.794782] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.794969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2258) -> (2894 - 4051), size 893 -> 1157 <7> [436.795229] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0 <7> [436.795478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.795725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.796000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [436.796242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [436.796483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [436.796719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.796976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.797214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [436.797499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [436.797925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [436.798288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [436.798640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [436.799006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [436.799360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [436.800974] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.801343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.802119] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [436.802427] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [436.810933] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.843735] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.844177] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [436.844127] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.844390] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 585 - 2894) -> ( 376 - 3312), size 2309 -> 2936 <7> [436.844497] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.844585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2894 - 4051) -> (3312 - 4051), size 1157 -> 739 <7> [436.844767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.844837] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.844960] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.845139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [436.845320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [436.845575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [436.846196] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.846507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [436.846738] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 585 - 2894) -> ( 376 - 3312), size 2309 -> 2936 <7> [436.846990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2894 - 4051) -> (3312 - 4051), size 1157 -> 739 <7> [436.847218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.847439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.847652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [436.847886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [436.848127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [436.848483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [436.848868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [436.849158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [436.849427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [436.849673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [436.851078] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.851442] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.893457] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.893677] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.893799] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.893802] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.893916] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 376) -> ( 0 - 679), size 376 -> 679 <7> [436.893956] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.894000] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 376 - 3312) -> ( 679 - 1358), size 2936 -> 679 <7> [436.894080] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3312 - 4051) -> (1358 - 2705), size 739 -> 1347 <7> [436.894086] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.894166] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2705 - 4051), size 0 -> 1346 <7> [436.894246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.894324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.894399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [436.894474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [436.894548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.894624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.894694] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [436.894764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [436.894944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [436.895071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [436.895186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [436.895306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [436.895429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [436.895554] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [436.896453] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.896587] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.909837] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [436.927941] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.928180] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.960805] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.960832] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [436.961303] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [436.961409] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [436.961758] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 679) -> ( 0 - 456), size 679 -> 456 <7> [436.961944] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [436.962104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 679 - 1358) -> ( 456 - 1360), size 679 -> 904 <7> [436.962411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1358 - 2705) -> (1360 - 2259), size 1347 -> 899 <7> [436.962704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2705 - 4051) -> (2259 - 4051), size 1346 -> 1792 <7> [436.963023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.963312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.963597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [436.963890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [436.964163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [436.964434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [436.964709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [436.965023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [436.965386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [436.965894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [436.966355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [436.966830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [436.967278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [436.967714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [436.969999] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [436.970402] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [436.977968] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [436.978290] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.010444] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.010826] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.010978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 456) -> ( 0 - 583), size 456 -> 583 <7> [437.011296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 456 - 1360) -> ( 583 - 2898), size 904 -> 2315 <7> [437.011319] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.011587] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1360 - 2259) -> (2898 - 4051), size 899 -> 1153 <7> [437.011756] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.011904] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2259 - 4051) -> ( 0 - 0), size 1792 -> 0 <7> [437.012186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.012464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.012741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.013023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.013280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [437.013534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.013795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.014039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.014365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [437.015299] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.015650] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 456) -> ( 0 - 583), size 456 -> 583 <7> [437.015928] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 456 - 1360) -> ( 583 - 2898), size 904 -> 2315 <7> [437.016179] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1360 - 2259) -> (2898 - 4051), size 899 -> 1153 <7> [437.016425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2259 - 4051) -> ( 0 - 0), size 1792 -> 0 <7> [437.016672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.016949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.017212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.017471] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.017724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [437.017988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.018229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.018471] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.018741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [437.019167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [437.019571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [437.019981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [437.020380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [437.020796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [437.022535] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.022922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.024088] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [437.024358] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [437.027575] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.060401] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.060829] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.060920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [437.061222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939 <7> [437.061323] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.061501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737 <7> [437.061799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.061809] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.062070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [437.062340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [437.062609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [437.062980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [437.063453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [437.063928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [437.064362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [437.064812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [437.065245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [437.066689] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.067148] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.110486] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.110841] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.110820] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.111163] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673 <7> [437.111361] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692 <7> [437.111342] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.111546] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333 <7> [437.111722] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353 <7> [437.111952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.111850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.112139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.112321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.112540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.112749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.112973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [437.113136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [437.113296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [437.113499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [437.113778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [437.114078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [437.114349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [437.114616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [437.114915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [437.116194] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.116502] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.126499] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [437.144001] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.144266] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.176782] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.177044] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.177318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452 <7> [437.177593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913 <7> [437.177865] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893 <7> [437.177897] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.178062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793 <7> [437.178252] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.178271] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.178442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [437.178592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.178631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [437.178903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [437.179109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.179327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.179515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.179740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.180023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [437.180318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [437.180585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [437.180869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [437.181160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [437.181400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [437.182334] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.182610] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.193816] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.194070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.226727] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.227012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 452) -> ( 0 - 583), size 452 -> 583 <7> [437.227202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 452 - 1365) -> ( 583 - 2898), size 913 -> 2315 <7> [437.227378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2258) -> (2898 - 4051), size 893 -> 1153 <7> [437.227549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0 <7> [437.227783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.227977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.227940] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.228159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.228337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.228284] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.228511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [437.228584] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.228724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.228962] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.229160] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.229403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [437.229678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [437.229964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [437.230212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [437.230454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [437.230695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [437.231646] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.231933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.232541] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [437.232776] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [437.243826] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.276716] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.277018] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375 <7> [437.277216] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939 <7> [437.277400] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737 <7> [437.277579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.277783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [437.277915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.277971] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [437.278189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [437.278263] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.278396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [437.278560] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.278676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [437.278972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [437.279225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [437.279523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [437.279782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [437.280594] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.280902] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.326754] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.327008] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.327291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673 <7> [437.327488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692 <7> [437.327676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333 <7> [437.327909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353 <7> [437.328087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.328043] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.328257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.328427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.328390] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.328628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.328685] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.328844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.329017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [437.329191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [437.329359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [437.329553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [437.329834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [437.330072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [437.330310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [437.330543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [437.330804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [437.331806] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.332074] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.343100] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [437.360511] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.360764] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.393471] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.393698] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.393984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452 <7> [437.394105] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.394192] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913 <7> [437.394359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893 <7> [437.394431] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.394521] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793 <7> [437.394680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.394709] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.394882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [437.395052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [437.395220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [437.395382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.395547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.395717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.395986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.396201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [437.396469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [437.396749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [437.396985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [437.397262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [437.397494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [437.398467] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.398755] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.410626] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.410934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.443659] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.443973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 452) -> ( 0 - 585), size 452 -> 585 <7> [437.444059] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.444181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 452 - 1365) -> ( 585 - 2894), size 913 -> 2309 <7> [437.444376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2258) -> (2894 - 4051), size 893 -> 1157 <7> [437.444403] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.444607] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0 <7> [437.444697] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.444839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.445012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [437.445187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [437.445386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [437.445552] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [437.445713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.445935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.446126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.446349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [437.446627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [437.446927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [437.447220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [437.447480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [437.447756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [437.448627] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.448919] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.449505] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [437.449725] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [437.460502] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.493396] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.493675] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376 <7> [437.493936] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 585 - 2894) -> ( 376 - 3312), size 2309 -> 2936 <7> [437.493999] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.494128] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2894 - 4051) -> (3312 - 4051), size 1157 -> 739 <7> [437.494310] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.494325] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.494487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [437.494607] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.494663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [437.494922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [437.495132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [437.495407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [437.495674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [437.495976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [437.496229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [437.496476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [437.497183] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.497448] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.543527] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.543930] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.544327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 376) -> ( 0 - 679), size 376 -> 679 <7> [437.544612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 376 - 3312) -> ( 679 - 1358), size 2936 -> 679 <7> [437.544925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3312 - 4051) -> (1358 - 2705), size 739 -> 1347 <7> [437.545070] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.545175] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2705 - 4051), size 0 -> 1346 <7> [437.545418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.545544] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.545660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [437.546017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [437.546011] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.546269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [437.546499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.546736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [437.546980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [437.547220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [437.547487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [437.547880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [437.548300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [437.548658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [437.549036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [437.549390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [437.550866] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.551241] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.559772] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [437.577480] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.577786] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.610040] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.610306] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.610581] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 679) -> ( 0 - 456), size 679 -> 456 <7> [437.610926] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 679 - 1358) -> ( 456 - 1360), size 679 -> 904 <7> [437.611059] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.611148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1358 - 2705) -> (1360 - 2259), size 1347 -> 899 <7> [437.611362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2705 - 4051) -> (2259 - 4051), size 1346 -> 1792 <7> [437.611453] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.611576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.611829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.611878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [437.612106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [437.612311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [437.612513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.612738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [437.612945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [437.613164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [437.613393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [437.613708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [437.614045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [437.614329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [437.614607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [437.614929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [437.616136] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.616431] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.627139] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.627402] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.659978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.660229] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 456) -> ( 0 - 814), size 456 -> 814 <7> [437.660443] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 456 - 1360) -> ( 814 - 2440), size 904 -> 1626 <7> [437.660623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1360 - 2259) -> (2440 - 4051), size 899 -> 1611 <7> [437.660847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2259 - 4051) -> ( 0 - 0), size 1792 -> 0 <7> [437.661037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.660997] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.661221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [437.661341] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.661407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [437.661623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [437.661634] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.661853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.662026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.662214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.662403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.662578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.662780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [437.662950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 8, 8, 8, 8, 8, 0, 0, 19, 4, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [437.663116] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [437.663277] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [437.663436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.663593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.663769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.663943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [437.664189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [437.664432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [437.664677] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [437.664999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [437.665251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [437.666079] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.666335] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.667018] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [437.667253] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [437.676852] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.709985] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.710282] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [437.710506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [437.710751] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [437.710949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.710894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.711139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [437.711242] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.711327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [437.711526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [437.711540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.711746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [437.712027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [437.712300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [437.712570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [437.712864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [437.713113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [437.713768] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.714053] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.759994] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.760269] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.760529] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896 <7> [437.760773] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471 <7> [437.760950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774 <7> [437.760889] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.761120] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910 <7> [437.761213] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.761284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.761478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.761487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.761660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.761911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.762079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.762242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [437.762405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [437.762600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [437.762844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [437.763100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [437.763353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [437.763599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [437.763918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [437.764159] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [437.765036] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.765296] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.776388] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [437.793743] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.793993] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.826634] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.826903] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.827146] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676 <7> [437.827366] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691 <7> [437.827552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335 <7> [437.827769] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349 <7> [437.827940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.827907] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.828139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [437.828233] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.828308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [437.828470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [437.828512] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.828640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.828846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.829025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.829197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.829395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [437.829669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [437.829967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [437.830215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [437.830474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [437.830769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [437.831741] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.831996] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.843668] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.843916] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.876774] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.877039] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 676) -> ( 0 - 814), size 676 -> 814 <7> [437.877238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 676 - 1367) -> ( 814 - 2440), size 691 -> 1626 <7> [437.877426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2702) -> (2440 - 4051), size 1335 -> 1611 <7> [437.877611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0 <7> [437.877846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.878018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.877992] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.878225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.878337] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.878418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.878580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [437.878628] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.878779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.878943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.879111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [437.879302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [437.879572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [437.879850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [437.880096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [437.880368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [437.880596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [437.881540] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.881841] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.882440] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [437.882653] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [437.893826] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.926618] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.926950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [437.927211] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [437.927408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [437.927598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.927832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [437.928008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [437.927979] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.928210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [437.928304] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.928409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [437.928579] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.928857] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.929061] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [437.929259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [437.929421] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [437.929583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.929776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [437.929954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [437.930152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [437.930323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [437.930575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [437.930841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [437.931153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [437.931410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [437.931665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [437.932413] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.932722] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.976625] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.976945] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.977218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896 <7> [437.977418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471 <7> [437.977605] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774 <7> [437.977833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910 <7> [437.978013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.977970] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [437.978226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.978316] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [437.978417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.978608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.978614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [437.978819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.978976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [437.979163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [437.979349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [437.979540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [437.979995] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [437.980191] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [437.980388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896 <7> [437.980549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471 <7> [437.980727] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774 <7> [437.980893] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910 <7> [437.981054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.981212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [437.981404] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [437.981584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [437.981824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [437.981985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [437.982151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [437.982303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [437.982465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [437.982744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [437.983057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [437.983319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [437.983578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [437.983905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [437.984922] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [437.985189] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [437.992980] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [438.010510] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.010787] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.043249] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.043472] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.043731] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676 <7> [438.043859] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.043928] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691 <7> [438.044116] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335 <7> [438.044204] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.044298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349 <7> [438.044478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.044497] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.044656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [438.044885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [438.045068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [438.045240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.045410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.045583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.045800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.045992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [438.046250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [438.046500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [438.046764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [438.047007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [438.047293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [438.048231] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.048490] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.060399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.060659] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.093424] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.093734] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 676) -> ( 0 - 817), size 676 -> 817 <7> [438.093858] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.093975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 676 - 1367) -> ( 817 - 2434), size 691 -> 1617 <7> [438.094167] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2702) -> (2434 - 4051), size 1335 -> 1617 <7> [438.094203] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.094356] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0 <7> [438.094496] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.094577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.094792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.094973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [438.095149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [438.095323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [438.095494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.095665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.096002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.096206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [438.096474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [438.096780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [438.097026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [438.097268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [438.097524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [438.098385] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.098638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.099306] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [438.099524] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [438.110425] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.143250] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.143511] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [438.143742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 817 - 2434) -> ( 588 - 2893), size 1617 -> 2305 <7> [438.143929] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2434 - 4051) -> (2893 - 4051), size 1617 -> 1158 <7> [438.143867] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.144108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.144194] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.144284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.144475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [438.144475] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.144693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [438.144891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [438.145200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [438.145459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [438.145728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [438.145988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [438.146235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [438.146936] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.147224] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.193613] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.193839] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.194003] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.194211] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.194304] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 588) -> ( 0 - 905), size 588 -> 905 <7> [438.194517] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 588 - 2893) -> ( 905 - 1360), size 2305 -> 455 <7> [438.194536] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.194754] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2893 - 4051) -> (1360 - 3152), size 1158 -> 1792 <7> [438.194933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3152 - 4051), size 0 -> 899 <7> [438.195108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.195281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.195452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [438.195656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [438.195878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.196064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.196221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [438.196371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [438.196558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [438.196839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [438.197105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [438.197364] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [438.197627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [438.197997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [438.199367] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.199699] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.209651] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [438.227130] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.227359] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.259893] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.260110] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.260334] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 905) -> ( 0 - 681), size 905 -> 681 <7> [438.260553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 905 - 1360) -> ( 681 - 1362), size 455 -> 681 <7> [438.260791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1360 - 3152) -> (1362 - 2707), size 1792 -> 1345 <7> [438.260969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3152 - 4051) -> (2707 - 4051), size 899 -> 1344 <7> [438.260939] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.261139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.261306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.261267] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.261474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [438.261543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.261652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [438.261869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.262036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.262226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [438.262389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [438.262577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [438.262854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [438.263104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [438.263347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [438.263584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [438.263911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [438.264924] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.265198] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.277078] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.277341] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.309905] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.310172] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 681) -> ( 0 - 814), size 681 -> 814 <7> [438.310412] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 681 - 1362) -> ( 814 - 2440), size 681 -> 1626 <7> [438.310602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1362 - 2707) -> (2440 - 4051), size 1345 -> 1611 <7> [438.310853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2707 - 4051) -> ( 0 - 0), size 1344 -> 0 <7> [438.311029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.311002] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.311201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.311330] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.311371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.311570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.311604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.311803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [438.311984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.312163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.312373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.312591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [438.312942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [438.313235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [438.313550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [438.313961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [438.314201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [438.315139] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.315398] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.316087] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [438.316301] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [438.327087] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.359934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.360215] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [438.360444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [438.360641] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [438.360903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.361082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [438.361052] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.361257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [438.361380] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.361462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [438.361699] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.361709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [438.362066] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.362271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [438.362433] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [438.362593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [438.362789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.362947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [438.363119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [438.363316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [438.363499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [438.363784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [438.364044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [438.364294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [438.364544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [438.364876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [438.365499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.365801] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.410001] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.410351] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.410583] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.410862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896 <7> [438.410963] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.411059] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471 <7> [438.411246] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774 <7> [438.411310] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.411429] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910 <7> [438.411606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.411678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.411869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.412049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.412260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.412463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.412674] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [438.412845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [438.413013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [438.413208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [438.413472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [438.413749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [438.414000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [438.414244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [438.414534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [438.415473] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.415746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.426284] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [438.443786] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.444036] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.476562] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.476935] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.477199] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676 <7> [438.477406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691 <7> [438.477604] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335 <7> [438.477866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349 <7> [438.478050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.478009] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.478229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [438.478352] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.478410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [438.478624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [438.478695] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.478868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.479048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.479246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.479462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.479726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [438.480174] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.480366] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.480569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676 <7> [438.480819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691 <7> [438.480989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335 <7> [438.481143] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349 <7> [438.481303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.481477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [438.481629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [438.481836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [438.481989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.482139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.482290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.482442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.482603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [438.482898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [438.483146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [438.483385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [438.483618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [438.483958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [438.484956] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.485216] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.493419] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.493603] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.526545] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.526866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 676) -> ( 0 - 814), size 676 -> 814 <7> [438.527132] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 676 - 1367) -> ( 814 - 2440), size 691 -> 1626 <7> [438.527353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2702) -> (2440 - 4051), size 1335 -> 1611 <7> [438.527566] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0 <7> [438.527836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.528034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.527960] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.528248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.528331] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.528469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.528692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [438.528688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.528866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.529038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.529205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.529406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [438.529708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [438.529980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [438.530244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [438.530506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [438.530795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [438.531923] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.532220] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.532887] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [438.533134] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [438.543530] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.576519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.576846] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586 <7> [438.577055] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310 <7> [438.577253] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155 <7> [438.577445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.577628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [438.577876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [438.578061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [438.578034] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.578291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [438.578360] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.578558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [438.578688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.578843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [438.579111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [438.579376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [438.579659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [438.580390] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.580688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.626539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.626831] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.627080] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896 <7> [438.627310] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471 <7> [438.627502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774 <7> [438.627711] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910 <7> [438.627875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.627855] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.628039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.628201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.628179] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.628387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.628460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.628561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.628788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [438.628963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [438.629123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [438.629310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [438.629579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [438.629866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [438.630105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [438.630343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [438.630627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [438.631735] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.631996] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.642892] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [438.660345] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.660575] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.693155] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.693385] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.693667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676 <7> [438.693794] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.693860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691 <7> [438.694035] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335 <7> [438.694137] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.694208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349 <7> [438.694374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.694420] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.694540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [438.694737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [438.694931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [438.695125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.695301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.695477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.695717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.695950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [438.696224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [438.696490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [438.696784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [438.697033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [438.697320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [438.698288] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.698544] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.710278] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.710533] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.743316] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.743578] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 676) -> ( 0 - 817), size 676 -> 817 <7> [438.743835] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 676 - 1367) -> ( 817 - 2434), size 691 -> 1617 <7> [438.744016] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2702) -> (2434 - 4051), size 1335 -> 1617 <7> [438.743991] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.744192] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0 <7> [438.744362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.744319] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.744529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.744598] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.744733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [438.744901] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [438.745099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [438.745281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.745468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.745640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.745821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [438.746079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [438.746333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [438.746584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [438.746887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [438.747149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [438.748135] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.748413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.749119] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [438.749368] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [438.760317] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.793178] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.793455] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588 <7> [438.793706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 817 - 2434) -> ( 588 - 2893), size 1617 -> 2305 <7> [438.793906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2434 - 4051) -> (2893 - 4051), size 1617 -> 1158 <7> [438.793832] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.794097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.794207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.794285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.794466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [438.794512] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.794693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [438.794891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [438.795152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [438.795408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [438.795676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [438.795971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [438.796220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [438.796960] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.797239] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.843181] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.843532] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.843854] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.843969] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.844124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 588) -> ( 0 - 905), size 588 -> 905 <7> [438.844319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 588 - 2893) -> ( 905 - 1360), size 2305 -> 455 <7> [438.844315] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.844506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2893 - 4051) -> (1360 - 3152), size 1158 -> 1792 <7> [438.844723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3152 - 4051), size 0 -> 899 <7> [438.844729] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.844897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.845090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.845272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [438.845461] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [438.845632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.845795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.845960] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [438.846120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [438.846308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [438.846577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [438.846882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [438.847154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [438.847417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [438.847709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [438.848889] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.849169] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.859560] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [438.877170] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.877414] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.909938] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.910175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.910420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 905) -> ( 0 - 681), size 905 -> 681 <7> [438.910704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 905 - 1360) -> ( 681 - 1362), size 455 -> 681 <7> [438.910899] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1360 - 3152) -> (1362 - 2707), size 1792 -> 1345 <7> [438.910837] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.911083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3152 - 4051) -> (2707 - 4051), size 899 -> 1344 <7> [438.911185] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.911266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.911446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.911485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.911699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [438.911880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [438.912053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.912216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [438.912384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [438.912551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [438.912780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4 <7> [438.913039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400 <7> [438.913288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400 <7> [438.913526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [438.913790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400 <7> [438.914091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382 <7> [438.915115] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.915390] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.927102] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [438.927366] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [438.959841] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 681) -> ( 0 - 2026), size 681 -> 2026 <7> [438.960049] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 681 - 1362) -> (2026 - 4051), size 681 -> 2025 <7> [438.960237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1362 - 2707) -> ( 0 - 0), size 1345 -> 0 <7> [438.960417] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2707 - 4051) -> ( 0 - 0), size 1344 -> 0 <7> [438.960590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.960832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.961018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.960966] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [438.961243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.961314] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [438.961450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.961647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.961653] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [438.961812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.961972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.962131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [438.962321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.962505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.962707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.962874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [438.963036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.963199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.963358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.963548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [438.964046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 681) -> ( 0 - 2026), size 681 -> 2026 <7> [438.964209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 681 - 1362) -> (2026 - 4051), size 681 -> 2025 <7> [438.964365] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1362 - 2707) -> ( 0 - 0), size 1345 -> 0 <7> [438.964519] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2707 - 4051) -> ( 0 - 0), size 1344 -> 0 <7> [438.964731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.964893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.965047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.965198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.965380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [438.965551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [438.965790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [438.966013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [438.966180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [438.966329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.966475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.966640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.966785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [438.966924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.967059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.967193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [438.967337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [438.967580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [438.967861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [438.968117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [438.968370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [438.968633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [438.969296] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [438.969558] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [438.970271] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [438.970508] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A] <7> [439.009782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [439.010036] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [439.010249] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.010449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [439.010713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [439.010845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.010937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [439.011191] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.011196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [439.011483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.011486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [439.011781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [439.012036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.012336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.012581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [439.013331] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.013594] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.043087] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.043339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [439.043573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [439.043831] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [439.044013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.043959] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.044194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.044307] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.044375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.044550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.044642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.044768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.044930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [439.045091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [439.045248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [439.045429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [439.045728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [439.045997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [439.046258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.046516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.046819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [439.047587] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.047922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.060080] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.093052] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.093275] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [439.093465] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [439.093668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [439.093830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.093812] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.093991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [439.094166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [439.094139] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.094364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [439.094420] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.094534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.094723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.094879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.095029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.095202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [439.095469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [439.095772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [439.096014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.096250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.096532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [439.097310] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.097570] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.110034] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.143084] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [439.143273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [439.143442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [439.143645] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.143813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.143789] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.143999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.144137] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.144202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.144375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [439.144430] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.144536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.144742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.144893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.145065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [439.145315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [439.145556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [439.145840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [439.146097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [439.146384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [439.147106] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.147378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.176467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [439.176693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [439.176873] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.176828] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.177044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [439.177248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [439.177201] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.177419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [439.177491] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.177620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [439.177874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [439.178126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [439.178409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.178664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.178911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [439.179713] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.179987] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.209753] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.209973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [439.210139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [439.210296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [439.210453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.210637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.210808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.210791] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.210976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.211141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.211155] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.211334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [439.211443] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.211521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [439.211735] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [439.211919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [439.212183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [439.212463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [439.212749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.213002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.213270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [439.214157] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.214403] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.226802] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.259738] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.260017] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [439.260254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [439.260450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [439.260682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.260878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [439.260820] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.261067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [439.261168] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.261281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [439.261463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.261467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.261672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.261838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.261997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.262198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [439.262474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [439.262755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [439.263013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.263266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.263512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [439.264412] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.264714] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.276858] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.310038] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [439.310277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [439.310480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [439.310726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.310908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.310854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.311103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [439.311179] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.311285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [439.311453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [439.311453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.311647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.311813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.312006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.312195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [439.312559] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [439.312771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [439.312930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [439.313085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.313238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.313412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [439.313613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [439.313775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [439.313937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.314095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.314253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.314420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [439.314715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [439.314977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [439.315237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [439.315494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [439.315779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [439.316616] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.316882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.343130] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [439.343412] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [439.343711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.343836] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.343922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.344147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [439.344208] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.344378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [439.344527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.344661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [439.345071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [439.345264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [439.345452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.345678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.345863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [439.346081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [439.346301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [439.346714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [439.346907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [439.347095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.347320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.347524] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [439.347765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [439.347955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [439.348246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [439.348529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [439.348847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.349158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.349419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [439.350270] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.350547] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.376501] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.376940] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [439.376984] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.377226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [439.377467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [439.377409] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.377756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.377822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.377985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.378210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [439.378478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [439.378741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.378989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.379199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [439.379406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [439.379676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [439.380267] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.380529] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [439.380799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [439.381013] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [439.381253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.381459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.381698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [439.381895] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [439.382100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.382300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.382500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [439.382747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [439.382981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [439.383289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [439.383639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [439.383940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.384233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.384502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [439.385473] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.385758] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.393024] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.426392] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.426748] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [439.426849] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.426977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [439.427193] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [439.427218] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.427400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.427537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.427631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.427824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [439.428047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [439.428234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.428408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.428598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [439.428769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [439.428964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [439.429234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [439.429500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [439.429791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.430079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.430361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [439.431351] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.431653] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.443397] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.476388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026 <7> [439.476699] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025 <7> [439.476813] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.476906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [439.477103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.477158] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.477295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.477453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.477483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.477758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.477951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [439.478132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.478336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.478513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.478767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [439.479039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [439.479314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [439.479607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [439.479874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [439.480137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [439.480868] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.481151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.526350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [439.526552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [439.526811] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.526996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [439.526950] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.527194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [439.527299] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.527406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [439.527628] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.527674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [439.527926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [439.528171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [439.528432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.528697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.528982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [439.529624] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.529881] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.559759] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.560061] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [439.560289] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [439.560506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [439.560817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.561020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.560967] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.561217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.561414] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.561370] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.561649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.561757] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.561846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [439.562040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [439.562232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [439.562449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [439.562791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [439.563142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [439.563438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.563761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.564084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [439.564906] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.565234] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.576700] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.609702] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.609962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [439.610158] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [439.610338] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [439.610512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.610743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [439.610927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [439.610886] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.611146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [439.611230] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.611350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.611525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.611530] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.611755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.611930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.612127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [439.612393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [439.612685] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [439.612959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.613217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.613478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [439.614275] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.614537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.626681] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.659701] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026 <7> [439.659932] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025 <7> [439.660136] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [439.660330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.660517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.660768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.660942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.660920] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.661145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [439.661246] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.661328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.661506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.661526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.661728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.661929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [439.662199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [439.662465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [439.662808] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [439.663057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [439.663306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [439.664131] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.664413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.693036] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361 <7> [439.693281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690 <7> [439.693488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.693746] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [439.693938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [439.693895] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.694158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [439.694246] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.694366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [439.694584] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.694655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [439.694926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [439.695178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.695424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.695744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [439.696533] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.696831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.726346] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.726605] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [439.726704] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.726787] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [439.726962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [439.727054] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.727133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.727301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.727351] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.727466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.727671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.727836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.727995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [439.728155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [439.728343] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [439.728569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [439.728939] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.729138] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293 <7> [439.729297] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597 <7> [439.729450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161 <7> [439.729640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.729791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.729942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.730090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.730243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.730396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [439.730569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [439.730721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [439.730881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [439.731141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [439.731397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [439.731678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.731982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.732240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [439.733115] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.733384] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.743094] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.776385] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.776705] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [439.776797] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.776915] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [439.777112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [439.777146] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.777303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.777445] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.777488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [439.777725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [439.777899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [439.778099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.778277] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.778455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.778657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.778846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [439.779194] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.779392] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615 <7> [439.779566] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823 <7> [439.779726] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613 <7> [439.779890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.780058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [439.780227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [439.780393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [439.780583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.780745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.780903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.781062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.781229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [439.781491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [439.781785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [439.782061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.782344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.782615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [439.783516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.783826] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.793080] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.826553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [439.826687] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.826785] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [439.826990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [439.827052] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.827186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.827377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.827346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.827591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [439.827775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [439.827982] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [439.828159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.828335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.828507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.828761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [439.829198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033 <7> [439.829362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018 <7> [439.829520] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0 <7> [439.829730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.829889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.830061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [439.830254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [439.830426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [439.830603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.830757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.830907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.831064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2 <7> [439.831313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [439.831567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [439.831826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [439.832067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [439.832304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [439.833019] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.833290] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.859697] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364 <7> [439.859949] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687 <7> [439.860159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.860356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.860582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [439.860706] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.860769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [439.861013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [439.861046] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.861290] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [439.861327] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.861560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [439.861820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.862080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.862373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [439.863215] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.863469] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.892957] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.893207] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316 <7> [439.893418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582 <7> [439.893643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153 <7> [439.893822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.893786] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.893994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.894178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [439.894132] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.894350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [439.894423] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.894517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.894735] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.894893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [439.895070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [439.895271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [439.895553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [439.895800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [439.896051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.896291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [439.896600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [439.897448] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.897744] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.909909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.942933] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.943179] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627 <7> [439.943358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814 <7> [439.943568] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610 <7> [439.943743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.943705] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.943906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.944069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [439.944031] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.944257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [439.944315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.944429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.944611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [439.944766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [439.944915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [439.945097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [439.945357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [439.945636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [439.945882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.946133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [439.946415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [439.947292] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.947566] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [439.959901] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [439.993020] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691 <7> [439.993245] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360 <7> [439.993449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0 <7> [439.993716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.993754] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [439.993905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [439.994120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [439.994122] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [439.994317] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [439.994440] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [439.994493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [439.994723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [439.994919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [439.995139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [439.995328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [439.995512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.995765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.995957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [439.996189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [439.996568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [439.996910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [439.997251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.997598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [439.997947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [439.998965] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [439.999321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.042996] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [440.043236] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [440.043425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.043655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.043773] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.043840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.044054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.044121] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.044259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [440.044421] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.044555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [440.044815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [440.045061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.045353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.045616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [440.046261] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.046529] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.077896] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:475] <7> [440.077759] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.078188] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.078564] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.100722] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.101119] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [440.101456] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [440.101796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [440.102034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.102266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.102496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.102830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.103060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.103282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [440.103482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [440.103725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [440.104017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [440.104328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [440.104656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [440.104997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.105288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.105733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [440.106579] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.106882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.110235] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.143017] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.143424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [440.143830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [440.144099] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [440.143992] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.144356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.144481] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.144694] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.144953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.144966] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.145206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.145523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.145768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.146076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.146341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.146659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [440.147032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [440.147424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [440.147838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.148256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.148639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [440.149649] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.150120] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.159918] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.192930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [440.193164] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [440.193366] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [440.193610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.193802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.193735] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.193987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.194083] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.194184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.194362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [440.194383] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.194563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.194737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.194898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.195085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [440.195453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [440.195660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [440.195818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [440.196017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.196186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.196349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.196527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.196697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [440.196912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.197097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.197278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.197467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [440.197819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [440.198157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [440.198463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [440.198859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [440.199218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [440.200118] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.200405] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.226362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [440.226675] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [440.226798] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.226888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.227082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.227144] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.227268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.227440] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.227489] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.227769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [440.228195] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [440.228378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [440.228578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.228748] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.228948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.229132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.229335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [440.229616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [440.229878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [440.230136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.230442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.230734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [440.231609] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.231887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.259721] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.260041] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [440.260269] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [440.260479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [440.260759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.260945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.260887] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.261127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.261237] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.261327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.261514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.261556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.261687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [440.261856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [440.262023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [440.262217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [440.262617] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.262828] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [440.262992] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [440.263153] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [440.263315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.263529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.263712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.263872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.264045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.264215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [440.264385] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [440.264586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [440.264762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [440.265030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [440.265294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [440.265571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.265837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.266105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [440.267036] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.267310] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.276325] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.309576] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.309856] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [440.310056] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [440.310240] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [440.310418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.310639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.310785] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.310847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.311063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.311133] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.311262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.311443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.311425] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.311677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.311849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.312037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [440.312476] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.312736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [440.312913] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [440.313086] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [440.313259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.313427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.313634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.313833] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.314026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.314186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.314342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.314508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.314673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [440.314929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [440.315182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [440.315457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.315748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.316026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [440.317017] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.317341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.326397] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.359791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [440.360026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [440.360230] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [440.360425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.360684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.360865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [440.360824] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.361075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [440.361150] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.361271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [440.361446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.361430] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.361657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.361823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.362014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [440.362264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [440.362525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [440.362783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [440.363034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [440.363327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [440.364049] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.364329] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.392921] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [440.393169] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [440.393382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.393633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.393762] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.393831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [440.394063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [440.394110] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.394278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [440.394406] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.394567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [440.394834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [440.395084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.395331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.395648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [440.396380] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.396663] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.426218] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.426463] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [440.426733] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [440.426913] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [440.426856] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.427091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.427203] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.427265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.427435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [440.427531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.427703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [440.427890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.428043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.428191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [440.428339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [440.428527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [440.428780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [440.429046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [440.429310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.429594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.429896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [440.430826] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.431101] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.443113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.476208] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.476451] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [440.476742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [440.476919] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [440.476893] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.477092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.477263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.477243] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.477432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [440.477570] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.477698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [440.477869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.478050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.478221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [440.478407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [440.478650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [440.478957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [440.479221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [440.479516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.479807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.480057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [440.480921] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.481183] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.493422] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.526218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691 <7> [440.526456] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360 <7> [440.526731] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0 <7> [440.526922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.526878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.527109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.527205] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.527292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.527522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.527506] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.527711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [440.527889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.528072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.528291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.528527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [440.528823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [440.529081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [440.529334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [440.529609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [440.529854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [440.530518] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.530800] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.559561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [440.559761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [440.559943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.560121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.560296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.560542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.560676] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.560756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [440.561014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [440.561037] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.561265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [440.561330] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.561531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.561835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.562091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [440.562708] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.562983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.592839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.593080] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [440.593259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [440.593431] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [440.593671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.593847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.593810] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.594019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.594156] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.594218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.594386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.594455] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.594590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [440.594760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [440.594919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [440.595102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [440.595350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [440.595625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [440.595877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.596107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.596350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [440.597063] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.597327] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.609839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.642834] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.643067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [440.643270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [440.643435] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [440.643660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.643829] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.643783] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.644015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.644130] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.644201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.644363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.644422] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.644556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.644716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.644878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.645064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [440.645435] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.645690] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [440.645862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [440.646028] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [440.646193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.646353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.646543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.646700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.646878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.647038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.647190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.647331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.647494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [440.647735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [440.647971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [440.648208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.648437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.648708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [440.649377] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.649654] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.659723] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.692908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [440.693140] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [440.693346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [440.693599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.693722] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.693794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.693985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.694070] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.694188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.694401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [440.694364] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.694618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.694790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.694952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.695139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [440.695523] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691 <7> [440.695698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360 <7> [440.695866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [440.696030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.696189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.696379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.696672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.696845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [440.697023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.697182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.697337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.697572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [440.697836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [440.698099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [440.698363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [440.698713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [440.699010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [440.699725] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.699999] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.726224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [440.726500] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [440.726709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.726631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.726896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.726996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.727073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.727275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.727269] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.727510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [440.727889] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [440.728060] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [440.728221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.728378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.728588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.728755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.728923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [440.729295] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026 <7> [440.729529] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025 <7> [440.729692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.729859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.730018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.730174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.730339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [440.730631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [440.730897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [440.731155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.731423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.731708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [440.732520] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.732793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.759598] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.759884] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [440.760127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [440.760318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [440.760535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.760710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.760674] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.760882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.761061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.761017] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.761227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.761298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.761388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [440.761579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [440.761736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [440.761914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [440.762351] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.762595] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910 <7> [440.762780] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391 <7> [440.762948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750 <7> [440.763107] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.763260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.763409] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.763601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.763759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.763917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [440.764075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [440.764231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [440.764397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [440.764701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [440.764966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [440.765222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.765494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.765779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [440.766693] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.766942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.776236] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.809586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.809901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293 <7> [440.810100] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597 <7> [440.810285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161 <7> [440.810487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.810661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [440.810645] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.810836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [440.810978] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.811054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [440.811257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.811277] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.811480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [440.811672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [440.811853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [440.812040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [440.812289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [440.812548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [440.812792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.813045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.813305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [440.814256] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.814549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.826590] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.859664] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701 <7> [440.859882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350 <7> [440.860074] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0 <7> [440.860257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.860435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.860679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [440.860855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [440.860798] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.861024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [440.861148] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.861214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.861378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.861428] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.861576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [440.861770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2 <7> [440.862050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [440.862325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [440.862624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [440.862893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [440.863158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [440.863948] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.864247] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.892835] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031 <7> [440.893068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020 <7> [440.893261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.893441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.893684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [440.893870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [440.893814] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.894121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2 <7> [440.894186] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.894398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [440.894513] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.894711] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [440.894964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.895208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [440.895516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [440.896334] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.896636] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.926143] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.926383] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939 <7> [440.926622] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375 <7> [440.926791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737 <7> [440.926766] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.926952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.927109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.927093] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.927281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [440.927365] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.927494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [440.927658] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.927847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.928008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [440.928165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [440.928361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [440.928680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [440.928931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [440.929173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.929411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [440.929681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [440.930543] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.930818] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.943038] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.976126] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [440.976378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310 <7> [440.976637] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586 <7> [440.976818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155 <7> [440.976759] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [440.976993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.977164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.977106] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [440.977333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [440.977404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [440.977534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [440.977700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [440.977907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [440.978084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [440.978251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [440.978462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [440.978774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [440.979029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [440.979318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.979595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [440.979839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [440.981657] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [440.981921] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [440.993237] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A] <7> [441.026125] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.026407] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597 <7> [441.026683] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293 <7> [441.026810] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.026884] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161 <7> [441.027080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.027181] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.027268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.027477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.027501] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.027681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.027884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.028057] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.028222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.028383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.028585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.028745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [441.028920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [441.029119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [441.029317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [441.029603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [441.029864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [441.030124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [441.030453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [441.030708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [441.031522] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.031794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.042529] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A] <7> [441.043138] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [441.043401] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [441.060130] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.092784] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.093065] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [441.093273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [441.093520] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [441.093716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.093671] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.093904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [441.094010] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.094078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [441.094275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [441.094284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.094487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [441.094855] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.095070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [441.095245] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [441.095413] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [441.095631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.095798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [441.095955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [441.096107] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [441.096269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [441.096548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [441.096801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [441.097063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [441.097324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [441.097643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [441.098321] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.098641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.142856] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.143246] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.143589] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.143608] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.143880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [441.143958] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.144076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [441.144262] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [441.144261] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.144465] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [441.144644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.144827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.145013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.145236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.145445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.145621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [441.145803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [441.145994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [441.146223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [441.146538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [441.146849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [441.147169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [441.147511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [441.147872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [441.148854] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.149199] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.159202] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [441.176680] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.176929] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.209574] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.209794] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.210033] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [441.210250] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [441.210479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [441.210665] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [441.210626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.210848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.211017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [441.210978] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.211187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [441.211250] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.211380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [441.211612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.211773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.211949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.212125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.212329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [441.212634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [441.212901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [441.213145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [441.213446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [441.213687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [441.214461] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.214734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.226474] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.226734] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.259413] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.259717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [441.259917] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [441.260107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [441.260290] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [441.260569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.260753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.260705] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.260931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.261052] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.261145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.261336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [441.261346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.261616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.261798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.261954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.262138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [441.262632] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.262852] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [441.263039] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [441.263194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [441.263345] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [441.263531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.263681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.263866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.264021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.264174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [441.264323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.264507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.264658] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.264818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [441.265079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [441.265334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [441.265618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [441.265872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [441.266118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [441.267123] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.267382] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.268064] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [441.268297] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [441.276270] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.309390] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.309692] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [441.309931] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [441.310123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [441.310298] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.310532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [441.310652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.310709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [441.310912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [441.310986] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.311138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [441.311283] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.311410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [441.311723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [441.311987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [441.312253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [441.312539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [441.313313] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.313953] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.359452] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.359720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.359989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [441.360173] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [441.360343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [441.360561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [441.360729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.360711] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.360924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.361091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.361038] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.361250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.361314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.361421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.361576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [441.361727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [441.361875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [441.362051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [441.362305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [441.362583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [441.362833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [441.363111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [441.363350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [441.364343] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.364648] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.375823] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [441.393142] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.393391] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.426086] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.426332] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.426640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [441.426755] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.426873] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [441.427071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [441.427142] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.427265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [441.427508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.427490] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.427702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [441.427897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [441.428131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [441.428336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.428564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.428753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.428929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.429136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [441.429417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [441.429753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [441.430035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [441.430375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [441.430873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [441.431903] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.432195] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.443119] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.443383] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.476220] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.476497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [441.476610] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.476725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [441.476920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [441.476940] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.477106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [441.477233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.477287] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.477500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [441.477683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [441.477898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [441.478064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [441.478225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.478387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.478599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.478785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [441.479036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [441.479283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [441.479553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [441.479799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [441.480098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [441.480941] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.481218] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.481906] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [441.482144] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [441.493107] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.526044] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.526330] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [441.526660] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.526749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [441.526952] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [441.527007] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.527146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.527298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.527337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [441.527620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [441.527816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [441.528071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [441.528373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [441.528708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [441.529001] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [441.529287] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [441.529660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [441.530417] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.530701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.576287] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.576764] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.576868] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.577129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [441.577301] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.577379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [441.577688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [441.577726] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.577901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [441.578108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.578358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [441.578622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [441.578810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [441.578989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.579165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [441.579336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [441.579585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [441.579815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [441.580140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [441.580458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [441.580759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [441.581077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [441.581478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [441.582799] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.583175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.592449] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [441.610127] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.610433] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.642874] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.643112] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.643354] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [441.643616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [441.643806] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [441.643747] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.643993] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [441.644093] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.644175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.644354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [441.644435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.644586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [441.644764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [441.644977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.645161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [441.645334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [441.645609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [441.645814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [441.646085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [441.646347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [441.646638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [441.646884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [441.647167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [441.648041] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.648300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.659805] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.659999] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.692812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.693065] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597 <7> [441.693297] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293 <7> [441.693527] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161 <7> [441.693708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [441.693675] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.693883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.694054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.694023] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.694258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.694318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.694478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.694666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [441.694828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.694987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.695147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.695332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [441.695626] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [441.695890] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [441.696174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [441.696494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [441.696773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [441.697428] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.697687] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.698340] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [441.698592] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [441.709790] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.742663] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.742920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [441.743116] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [441.743306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [441.743552] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.743737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [441.743688] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.743926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [441.744045] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.744130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [441.744337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [441.744336] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.744642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [441.744905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [441.745221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [441.745525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [441.745780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [441.746463] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.746730] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.792796] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.793092] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.793345] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [441.793633] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [441.793818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [441.793776] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.793997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [441.794172] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.794128] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.794344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.794450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.794572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.794743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.794932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.795106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [441.795258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [441.795444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [441.795631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [441.795887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [441.796138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [441.796395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [441.796663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [441.796911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [441.797760] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.798040] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.809082] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [441.826390] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.826622] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.859316] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.859567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.859790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [441.859997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [441.860183] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [441.860364] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [441.860609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.860791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [441.860747] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.860969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [441.861093] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.861187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [441.861395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.861412] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.861607] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.861782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.861946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.862133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [441.862403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [441.862651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [441.862899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [441.863156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [441.863421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [441.864248] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.864549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.876349] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.876653] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [441.909322] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.909631] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597 <7> [441.909875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293 <7> [441.910053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161 <7> [441.910225] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [441.910430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.910601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [441.910565] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.910768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [441.910900] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.910963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [441.911134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [441.911203] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.911302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.911509] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.911676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [441.911880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [441.912139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [441.912400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [441.912644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [441.912898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [441.913172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [441.914224] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.914548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [441.915165] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2 <7> [441.915424] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [441.926307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.959310] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [441.959630] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391 <7> [441.959890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910 <7> [441.960083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750 <7> [441.960262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [441.960490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [441.960671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [441.960549] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [441.960888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [441.961135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [441.961205] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [441.961424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [441.961691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [441.961771] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [441.961940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [441.962184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [441.962439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [441.963194] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [441.963525] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [442.009547] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.009925] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.010265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686 <7> [442.010655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686 <7> [442.010890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340 <7> [442.010766] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [442.011117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339 <7> [442.011338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.011405] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [442.011619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [442.011860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [442.011885] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [442.012072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [442.012281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.012544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [442.012752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [442.012965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [442.013213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [442.013585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [442.013922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [442.014255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [442.014615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [442.014984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [442.016285] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [442.016669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [442.025678] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [442.042761] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.043004] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.075950] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.076163] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.076426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468 <7> [442.076534] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [442.076652] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904 <7> [442.076844] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904 <7> [442.076873] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [442.077032] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775 <7> [442.077214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.077173] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [442.077427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [442.077608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [442.077802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [442.077981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.078143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [442.078307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [442.078521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [442.078730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [442.079028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [442.079297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [442.079591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [442.079907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [442.080161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [442.081101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [442.081401] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [442.093146] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.093449] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.126216] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.126502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599 <7> [442.126592] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [442.126718] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286 <7> [442.126896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166 <7> [442.126917] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [442.127067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0 <7> [442.127197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [442.127237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.127479] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [442.127662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [442.127862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [442.128050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [442.128210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [442.128390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [442.128549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [442.128731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3 <7> [442.128989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400 <7> [442.129239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400 <7> [442.129505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [442.129745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400 <7> [442.129991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826 <7> [442.130882] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [442.131161] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [442.131862] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2 <7> [442.132099] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [442.143102] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.175929] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.176209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [442.176483] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [442.176684] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [442.176624] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [442.176879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.176972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [442.177059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [442.177233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [442.177254] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [442.177475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [442.177698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [442.178117] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.178322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392 <7> [442.178580] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907 <7> [442.178749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752 <7> [442.178909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.179069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [442.179229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 <7> [442.179460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 <7> [442.179654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3 <7> [442.179914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400 <7> [442.180183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400 <7> [442.180496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [442.180754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400 <7> [442.181007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556 <7> [442.181757] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [442.182028] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [442.226047] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.226336] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.226668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [442.226661] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [442.226870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [442.227057] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [442.227018] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [442.227237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [442.227312] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [442.227448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.227624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [442.227791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [442.227980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [442.228156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.228359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [442.228514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [442.228666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [442.228859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [442.229360] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.229556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.229755] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693 <7> [442.229923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672 <7> [442.230089] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353 <7> [442.230273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333 <7> [442.230514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.230688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [442.230864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [442.231047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [442.231228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.231450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [442.231628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 <7> [442.231806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 <7> [442.231996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4 <7> [442.232296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400 <7> [442.232635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400 <7> [442.232946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [442.233214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400 <7> [442.233522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191 <7> [442.234694] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [442.235024] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [442.242363] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [442.259805] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.260075] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.292592] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.292820] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.293050] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471 <7> [442.293256] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896 <7> [442.293485] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910 <7> [442.293662] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774 <7> [442.293606] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [442.293834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.293936] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [442.294012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [442.294192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [442.294238] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [442.294420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [442.294596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.294776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 <7> [442.294946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 <7> [442.295139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 <7> [442.295374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [442.295627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [442.295883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [442.296144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [442.296411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [442.296715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [442.297606] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [442.297882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [442.309672] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.309933] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.342621] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.342902] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823 <7> [442.343117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614 <7> [442.343320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614 <7> [442.343601] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0 <7> [442.343625] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [442.343791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.343970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [442.344026] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [442.344153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [442.344370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [442.344313] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [442.344548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.344719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [442.344891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [442.345093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [442.345282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.345510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [442.345680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [442.345846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [442.346009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [442.346168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [442.346327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [442.346546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [442.346735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3 <7> [442.347026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400 <7> [442.347267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400 <7> [442.347538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [442.347827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400 <7> [442.348078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921 <7> [442.348819] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [442.349103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [442.349837] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2 <7> [442.350067] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A] <7> [442.359518] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.392559] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.392827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597 <7> [442.393033] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293 <7> [442.393227] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161 <7> [442.393463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.393650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [442.393607] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [442.393849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [442.393948] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [442.394025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 <7> [442.394215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3 <7> [442.394229] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [442.394502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400 <7> [442.394758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400 <7> [442.395005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [442.395245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400 <7> [442.395512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651 <7> [442.396165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [442.396446] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [442.442756] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.443124] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.443586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904 <7> [442.443679] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [442.443839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468 <7> [442.444074] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776 <7> [442.444135] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [442.444298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903 <7> [442.444580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.444573] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [442.444806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 <7> [442.445050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 <7> [442.445278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 <7> [442.445553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.445758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 <7> [442.445970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 <7> [442.446169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 <7> [442.446450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4 <7> [442.446784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400 <7> [442.447141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400 <7> [442.447537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [442.447950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400 <7> [442.448299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286 <7> [442.449676] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [442.450066] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [442.458980] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A] <7> [442.476289] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.476579] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.509242] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A] <7> [442.509487] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A] <7> [442.509714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686 <7> [442.509917] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686 <7> [442.510106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340 <7> [442.510288] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339 <7> [442.510533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [442.510712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 <7> [442.510681] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [442.510891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 <7> [442.511023] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<6> [424.160440] Console: switching to colour dummy device 80x25

<6> [424.160746] [IGT] kms_rotation_crc: executing

<7> [424.166295] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]

<7> [424.166305] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]

<7> [424.166454] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected

<7> [424.166682] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]

<7> [424.166685] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]

<7> [424.166803] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected

<7> [424.167031] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]

<7> [424.167035] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]

<7> [424.167180] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected

<7> [424.167455] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1]

<7> [424.167458] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:392:eDP-1]

<7> [424.167899] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00

<7> [424.168283] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000

<7> [424.168406] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [424.168511] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [424.168628] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz

<5> [424.168632] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [424.168634] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [424.168635] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] DisplayID extension version 0x13, primary use 0x00

<7> [424.168637] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<5> [424.168639] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [424.168640] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD monitor

<5> [424.168642] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [424.168643] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD size 20, SAD count 0

<5> [424.168645] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [424.168656] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] VRR capable: yes

<7> [424.168736] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [424.168816] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<5> [424.169324] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [424.169327] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<5> [424.169328] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)

<7> [424.169386] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1] probed modes:

<7> [424.169390] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [424.169395] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [424.169408] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]

<7> [424.169412] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]

<7> [424.169556] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected

<7> [424.169567] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]

<7> [424.169571] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]

<7> [424.169687] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected

<7> [424.169695] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]

<7> [424.169698] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]

<7> [424.169799] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected

<6> [424.170175] [IGT] kms_rotation_crc: starting subtest multiplane-rotation-cropping-top

<7> [424.171593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0

<7> [424.171679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [424.171743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.171806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.171867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.171945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0

<7> [424.172061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400

<7> [424.172167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400

<7> [424.172269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [424.172358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400

<7> [424.172441] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0

<7> [424.172762] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.172861] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.172987] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2

<7> [424.195823] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A

<7> [424.196199] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A

<7> [424.196481] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [424.196698] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000

<7> [424.196853] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000

<7> [424.197024] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation

<7> [424.197152] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [424.197298] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A]

<7> [424.197483] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [fastset]

<7> [424.197633] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [424.197768] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [424.197901] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>

<7> [424.198087] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [424.198214] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0

<7> [424.198338] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0

<7> [424.198460] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64

<7> [424.198580] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [424.198699] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled

<7> [424.198817] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled

<7> [424.198932] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled

<7> [424.199058] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0

<7> [424.199170] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [424.199280] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8

<7> [424.199390] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB

<7> [424.199499] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB

<7> [424.199608] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0

<7> [424.199711] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range

<7> [424.199814] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined

<7> [424.199915] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1

<7> [424.200078] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0

<7> [424.200174] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97

<7> [424.200268] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906

<7> [424.200362] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0

<7> [424.200453] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [424.200543] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa

<7> [424.200633] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [424.200723] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa

<7> [424.200810] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa

<7> [424.200897] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855

<7> [424.200987] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0

<7> [424.201072] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [424.201154] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [424.201235] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0

<7> [424.201315] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no

<7> [424.201395] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,

<7> [424.201473] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.

<7> [424.201551] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:

<7> [424.201628] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21

<7> [424.201704] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1

<7> [424.201781] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0

<7> [424.201858] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0

<7> [424.201940] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1

<7> [424.202038] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23

<7> [424.202116] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [424.202193] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [424.202268] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [424.202339] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [424.202409] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [424.202479] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [424.202552] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [424.202626] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [424.202699] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [424.202774] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [424.202848] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [424.202933] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [424.203022] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0

<7> [424.212136] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]

<7> [424.212280] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]

<7> [424.232028] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.232462] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.232810] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.262765] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:429]

<7> [424.284836] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 2026), size 0 -> 2026

<7> [424.285280] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 0 - 0) -> (2026 - 4051), size 0 -> 2025

<7> [424.285570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.285837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [424.286131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [424.286388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [424.286647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.286907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [424.287195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [424.287462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [424.287798] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [424.288340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [424.288748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [424.289166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [424.289571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [424.289996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [424.291552] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.292004] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.295399] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [424.295754] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A]

<7> [424.311918] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1

<7> [424.314283] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]

<7> [424.332001] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.332324] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.332539] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.336129] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.336391] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.363052] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]

<7> [424.364041] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.364646] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.365208] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.385141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [424.385276] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [424.385364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.385442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [424.385515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [424.385587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [424.385685] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [424.385808] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [424.385924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [424.386050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [424.386164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [424.386281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [424.386449] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 43464 kHz

<7> [424.386917] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.387072] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.413572] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.414203] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.414654] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.415264] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]

<7> [424.437126] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.437296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [424.437384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [424.437463] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [424.437537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.437609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [424.437679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [424.437748] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [424.437817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.437885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [424.437971] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [424.438042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [424.438140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [424.438377] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.438497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [424.438579] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [424.438657] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [424.438742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.438822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [424.438899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [424.439060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [424.439136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.439204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [424.439272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [424.439340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [424.439416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [424.439536] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [424.439656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [424.439778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [424.439907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [424.440041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [424.440499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.440623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.446740] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]

<7> [424.460307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.479987] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435]

<7> [424.479987] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.480408] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.480720] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.495821] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.496012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [424.496102] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [424.496182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [424.496258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.496331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [424.496403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [424.496473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [424.496544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.496613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [424.496683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [424.496752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [424.496843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [424.497046] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.497150] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [424.497231] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [424.497308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [424.497390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.497473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [424.497551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [424.497622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [424.497695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.497768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [424.497842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [424.497917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [424.498008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [424.498131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [424.498245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [424.498357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [424.498469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [424.498584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [424.499125] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.499258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.513514] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436]

<7> [424.529962] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.530222] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.530380] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.531638] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.532373] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.532533] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.562959] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:437]

<7> [424.563982] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.564459] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.564890] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.592076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [424.592419] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [424.592649] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [424.592858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.593079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [424.593259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [424.593435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [424.593604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [424.593764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.593941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.594103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.594298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [424.594820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [424.594996] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [424.595184] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [424.595320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.595453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [424.595587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [424.595712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [424.595839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [424.596151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.596274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.596391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.596516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [424.596709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [424.596896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [424.597089] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [424.597261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [424.597430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [424.598179] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.598363] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.629010] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.629669] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]

<7> [424.629496] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.629914] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.662084] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [424.662281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [424.662365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.662445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [424.662520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [424.662591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [424.662702] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [424.662825] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [424.663101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [424.663220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [424.663334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [424.663446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [424.664222] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.664372] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.695971] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.696458] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.696957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.697307] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439]

<7> [424.719178] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.719450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [424.719539] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [424.719618] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [424.719692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.719764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [424.719833] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [424.719902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [424.720019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.720094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [424.720165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [424.720236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [424.720339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [424.720463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [424.720578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [424.720691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [424.720803] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [424.720929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [424.721643] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.721786] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.730228] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:440]

<7> [424.744488] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.779962] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.780493] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:441]

<7> [424.780553] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.781112] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.803761] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.804077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [424.804182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [424.804270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [424.804353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.804432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [424.804509] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [424.804587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [424.804662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.804736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [424.804810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [424.804882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [424.805013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [424.805141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [424.805257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [424.805371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [424.805483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [424.805594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [424.806168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.806287] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.813407] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:442]

<7> [424.827740] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.863459] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:443]

<7> [424.863940] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.864453] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.864953] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.895196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [424.895413] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [424.895498] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [424.895577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.895655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [424.895727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [424.895797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [424.895866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [424.896031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.896108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.896179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [424.896282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [424.896406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [424.896523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [424.896634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [424.896746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [424.896856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [424.897464] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.897606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.929571] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:444]

<7> [424.929967] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.930406] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.930822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.958247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [424.958461] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [424.958550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.958627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [424.958703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [424.958775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [424.958884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [424.959032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [424.959151] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [424.959267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [424.959378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [424.959490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [424.960165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.960313] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [424.979866] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:445]

<7> [424.979915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [424.980180] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [424.980409] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [424.993978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [424.994136] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [424.994224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [424.994301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [424.994374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.994444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [424.994515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [424.994584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [424.994652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [424.994720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [424.994788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [424.994855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [424.994957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [424.995081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [424.995195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [424.995307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [424.995417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [424.995527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [424.996063] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [424.996186] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.014216] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:446]

<7> [425.029922] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.030240] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.030462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.036675] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.037516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.037687] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.066946] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.067460] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.067969] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.070538] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:447]

<7> [425.094004] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.094261] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [425.094408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [425.094523] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [425.094631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.094737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.094842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [425.094976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [425.095070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.095161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.095250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [425.095347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [425.095478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [425.095608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [425.095731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [425.095851] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [425.095989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [425.096105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [425.096650] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.096780] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.114747] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:448]

<7> [425.128926] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.129192] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.129390] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.131490] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.132203] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.132432] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.163413] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:449]

<7> [425.163377] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.163919] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.164362] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.189759] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026

<7> [425.190048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025

<7> [425.190216] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [425.190374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.190519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [425.190659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [425.190816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [425.191026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [425.191163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.191300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.191450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.191608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [425.191899] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026

<7> [425.192014] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025

<7> [425.192122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [425.192225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.192325] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [425.192421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [425.192523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [425.192622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [425.192710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.192802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.193001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.193141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [425.193302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [425.193446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [425.193585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [425.193711] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [425.193833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [425.194363] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.194527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.194908] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [425.194924] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [425.194921] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4

<7> [425.195755] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:450]

<7> [425.229149] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:451]

<7> [425.229928] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.230482] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.230970] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.254363] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [425.254717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [425.254979] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.255186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [425.255375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [425.255546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [425.255760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [425.256202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [425.256368] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [425.256517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.256658] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [425.256805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [425.257020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [425.257170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [425.257495] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [425.257629] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [425.257756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.257894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [425.258029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [425.258153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [425.258280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [425.258472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [425.258655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [425.258832] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [425.259015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [425.259186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [425.259920] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.260098] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.278928] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.279352] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.279723] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:452]

<7> [425.279714] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.304064] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.304342] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [425.304514] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [425.304670] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [425.304801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.305092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [425.305250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [425.305383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [425.305497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.305600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [425.305702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [425.305806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [425.305962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [425.306229] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.306348] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [425.306437] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [425.306528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [425.306623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.306725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [425.306823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [425.306951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [425.307049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.307140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [425.307219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [425.307308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [425.307400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [425.307516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [425.307624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [425.307725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [425.307837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [425.307974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [425.308364] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.308484] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.312660] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:453]

<7> [425.323085] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.346083] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:454]

<7> [425.346896] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.347263] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.347598] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.365977] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.366265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [425.366448] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [425.366610] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [425.366759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.366937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [425.367078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [425.367227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [425.367354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.367473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [425.367590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [425.367721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [425.367903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [425.368085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [425.368255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [425.368418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [425.368577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [425.368742] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [425.369459] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.369633] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.380169] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:455]

<7> [425.395905] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.396352] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.396714] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.401486] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.402411] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.402717] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.429047] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:456]

<7> [425.429018] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.429501] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.429978] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.449166] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [425.449521] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [425.449814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [425.450156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.450414] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [425.450668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [425.450995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [425.451236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [425.451473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.451704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.452134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.452405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [425.452740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [425.453112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [425.453450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [425.453816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [425.454161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [425.455183] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.455521] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.479578] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:457]

<7> [425.479904] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.480390] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.480804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.504510] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [425.505113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [425.505352] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.505562] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [425.505762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [425.505987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [425.506240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [425.506570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [425.506892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [425.507199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [425.507499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [425.507800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [425.509033] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.509309] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.528880] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.529392] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.529824] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.530692] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:458]

<7> [425.554399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.554678] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [425.554787] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [425.554905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [425.555000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.555090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [425.555174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [425.555255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [425.555335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.555410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [425.555484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [425.555558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [425.555662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [425.555792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [425.556123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [425.556247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [425.556360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [425.556472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [425.557295] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.557450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.563409] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:459]

<7> [425.574208] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.595879] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.596209] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.596470] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.597960] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:460]

<7> [425.613702] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.613870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [425.613959] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [425.614036] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [425.614109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.614181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [425.614251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [425.614320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [425.614390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.614458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [425.614527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [425.614595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [425.614681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [425.614801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [425.614926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [425.615040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [425.615152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [425.615262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [425.615794] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.616011] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.631198] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:461]

<7> [425.645479] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.680050] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:462]

<7> [425.679887] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.680473] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.680957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.698272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [425.698494] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [425.698604] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [425.698704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.698799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.698936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [425.699031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [425.699126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [425.699210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.699292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.699372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.699491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [425.699629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [425.699757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [425.699990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [425.700112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [425.700227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [425.700832] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.700957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.729578] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:463]

<7> [425.729876] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.730350] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.730771] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.750116] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [425.750239] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [425.750322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.750399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.750472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [425.750543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [425.750633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [425.750755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [425.750981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [425.751096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [425.751208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [425.751319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [425.751817] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.751945] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.778854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.779271] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.779623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.780294] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:464]

<7> [425.802226] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.802396] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [425.802487] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [425.802569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [425.802647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.802721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.802794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [425.803104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [425.803176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.803244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.803312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [425.803380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [425.803469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [425.803655] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.803746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [425.803910] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [425.803983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [425.804053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.804123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.804194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [425.804262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [425.804330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.804397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.804464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [425.804531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [425.804605] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [425.804720] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [425.804838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [425.804951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [425.805062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [425.805172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [425.805697] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.805838] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.813973] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:465]

<7> [425.827524] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.846394] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:466]

<7> [425.846851] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.847150] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.847346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.863045] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.863223] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [425.863311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [425.863388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [425.863462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.863534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.863604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [425.863673] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [425.863743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.863829] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.863900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [425.863969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [425.864056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [425.864239] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.864330] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [425.864400] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [425.864469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [425.864536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.864604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.864673] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [425.864742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [425.864936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.865008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [425.865076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [425.865143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [425.865217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [425.865332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [425.865445] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [425.865555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [425.865664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [425.865775] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [425.866391] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.866516] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.881375] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:467]

<7> [425.893355] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [425.912030] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691

<7> [425.912299] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360

<7> [425.912477] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [425.912643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.912911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [425.912876] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.913074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [425.913226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [425.913236] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.913373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.913516] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [425.913511] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.913652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [425.913786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [425.913928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [425.914059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.914189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.914316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.914480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [425.914936] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691

<7> [425.915070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360

<7> [425.915191] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [425.915308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.915421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [425.915535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [425.915647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [425.915763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.915916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [425.916030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [425.916139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [425.916248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [425.916349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.916452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.916554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [425.916666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [425.916854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [425.917027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [425.917186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [425.917342] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [425.917497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [425.918112] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.918274] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [425.962093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [425.962389] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [425.962633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [425.962904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [425.963138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [425.963037] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [425.963365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [425.963537] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [425.963632] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [425.964025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [425.964080] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [425.964391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [425.964752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [425.965127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [425.965483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [425.966552] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [425.966934] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.000393] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.000936] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:468]

<7> [426.000935] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.001367] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.021525] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.021859] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [426.021964] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [426.022051] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [426.022131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.022207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.022280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.022349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.022419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.022486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [426.022555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [426.022624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [426.022728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [426.022862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [426.022979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [426.023091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.023201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.023311] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [426.024008] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.024148] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.028848] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.062244] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.062860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [426.062869] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.063222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [426.063432] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.063552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [426.063944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.063961] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.064257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [426.064564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [426.064869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [426.065141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.065411] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.065683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.065978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.066310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [426.066773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [426.067236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [426.067655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.068067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.068452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [426.068948] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 43464 kHz -> 65196 kHz

<7> [426.070140] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.070469] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.078840] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.112108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [426.112466] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [426.112764] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [426.113099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.113109] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.113385] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.113549] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.113663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.113970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.113987] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.114239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [426.114500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.114766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.115032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.115319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [426.115731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [426.116961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [426.117367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [426.117753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [426.118155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [426.119454] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.119878] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.145291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [426.145553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [426.145819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.145826] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.146031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [426.146153] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.146237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [426.146441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [426.146457] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.146683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [426.147041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [426.147374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [426.147701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [426.148047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [426.148366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [426.149548] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.149897] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.178653] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.179012] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.179116] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [426.179378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [426.179383] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.179623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [426.179733] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.179901] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.180147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.180389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.180628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.180888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.181124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [426.181360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [426.181594] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [426.181888] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [426.182259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [426.182613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [426.182982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.183331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.183678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [426.185166] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.185536] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.195311] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.228665] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.228799] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.229066] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [426.229210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.229318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [426.229546] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [426.229566] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.229796] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.230022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [426.230246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [426.230465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [426.230684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.230918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.231137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.231353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.231619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [426.232014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [426.232378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [426.232733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.233099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.233448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [426.234902] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.235245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.245449] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.278806] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.278988] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [426.279172] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.279271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [426.279514] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [426.279505] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.279745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.279993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.280222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [426.280444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [426.280662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [426.280900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.281120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.281333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.281592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [426.282174] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [426.282393] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [426.282596] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [426.282839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.283039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.283236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [426.283431] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [426.283632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [426.283865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.284071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.284266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.284481] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [426.284845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [426.285178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [426.285501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [426.285840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [426.286167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [426.287331] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.287679] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.311980] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [426.312202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [426.312362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.312521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.312682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [426.312893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [426.312917] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.313108] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [426.313320] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.313509] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [426.313606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.313669] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [426.313839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.313988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.314128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [426.314266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [426.314418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [426.314647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [426.314877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [426.315094] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [426.315298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [426.315501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [426.316343] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.316540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.345465] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.345912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [426.345862] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.346188] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [426.346278] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.346440] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [426.346685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.346658] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.346961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.347210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [426.347451] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [426.347691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.347935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.348152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [426.348368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [426.348627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [426.349199] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.349492] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [426.349716] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [426.349960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [426.350179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.350394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.350611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [426.350840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [426.351053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.351266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.351484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [426.351697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [426.351940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [426.352307] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [426.352664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [426.353040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.353389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.353713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [426.355134] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.355435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.362027] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.395277] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.395677] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [426.396015] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [426.396076] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.396278] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [426.396531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.396544] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.396801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.396976] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.397049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [426.397290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [426.397530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.397801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.398039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [426.398274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [426.398559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [426.399327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.399643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [426.399896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [426.400112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [426.400327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.400544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.400784] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [426.401000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [426.401216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.401429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.401645] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [426.401888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [426.402123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [426.402483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [426.402860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [426.403213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.403561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.403923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [426.405315] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.405613] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.412337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.445234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691

<7> [426.445553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360

<7> [426.445894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0

<7> [426.446038] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.446141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.446378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.446473] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.446611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.446888] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.446954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.447197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [426.447443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.447712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.448056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.448324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [426.448707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [426.449102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [426.449505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [426.449862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [426.450195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [426.451039] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.451408] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.478639] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [426.479060] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [426.479189] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.479340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.479600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [426.479653] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.479904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [426.480081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.480140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [426.480455] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [426.480817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [426.481170] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [426.481505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [426.481993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [426.482368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [426.483220] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.483580] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.511868] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.512231] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [426.512501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [426.512724] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [426.513030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.513132] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.513265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.513515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.513563] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.513799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.514014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.513986] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.514224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [426.514436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [426.514666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [426.514995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [426.515320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [426.515637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [426.515991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.516320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.516624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [426.517574] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.517956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.528684] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.561830] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.562187] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [426.562448] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [426.562689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [426.563030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.563162] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.563291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [426.563521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [426.563591] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.563771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [426.563991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.564019] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.564208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.564425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.564695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.565050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [426.565399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [426.565773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [426.566088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.566390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.566758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [426.567751] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.568096] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.578672] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.611843] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [426.612135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [426.612373] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [426.612600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.612876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.613010] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.613104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.613321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.613412] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.613554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [426.613781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.613796] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.613989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.614213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.614502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [426.614836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [426.615142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [426.615431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [426.615740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [426.616045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [426.616904] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.617235] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.645150] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [426.645444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [426.645681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.645997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [426.646084] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.646220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [426.646466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [426.646457] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.646709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [426.646804] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.647055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [426.647367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [426.647647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [426.647966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [426.648304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [426.649306] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.649621] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.678488] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.678869] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [426.678949] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.679137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [426.679353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [426.679353] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.679563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.679695] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.679817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.680022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.680274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.680506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.680700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [426.680940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [426.681117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [426.681333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [426.681622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [426.681970] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [426.682288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.682581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.682901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [426.684055] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.684383] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.695405] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.728432] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.728790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [426.728894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.729070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [426.729301] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [426.729295] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.729521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.729638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.729771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [426.729973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [426.730181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [426.730371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.730557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.730793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.730989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.731197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [426.731590] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.731857] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [426.732056] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [426.732268] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [426.732467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.732666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [426.732921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [426.733134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [426.733349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.733529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.733740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.733923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.734101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [426.734395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [426.734687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [426.735041] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.735385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.735698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [426.736775] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.737078] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.745373] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.778827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [426.778878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.779135] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [426.779310] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.779396] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [426.779641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.779685] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.779953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.780223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [426.780498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [426.780779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [426.781028] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.781267] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.781553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.781897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [426.782444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [426.782749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [426.782989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [426.783221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.783443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.783742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [426.783965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [426.784206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [426.784439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.784662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.784927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [426.785184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [426.785507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [426.785830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [426.786145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [426.786453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [426.786766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [426.787687] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.788070] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.811855] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [426.812172] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [426.812428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.812668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.812975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [426.813189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [426.813118] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.813451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [426.813520] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.813920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [426.813917] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.814134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [426.814340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.814534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.814751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [426.814970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [426.815196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [426.815628] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [426.815874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [426.816071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.816250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.816422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [426.816576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [426.816767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [426.817035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [426.817305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [426.817602] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [426.817870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [426.818149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [426.818888] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.819130] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.845142] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.845537] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [426.845898] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [426.846037] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.846172] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [426.846436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.846506] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.846689] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.846957] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.847009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [426.847303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [426.847596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.847921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.848146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [426.848357] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [426.848616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [426.849264] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.849532] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [426.849745] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [426.849930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [426.850111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.850339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.850547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [426.850844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [426.851027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.851186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.851338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [426.851485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [426.851644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [426.851982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [426.852226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [426.852457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.852721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [426.852931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [426.853795] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.854029] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.858731] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turning VDD off

<7> [426.858931] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067

<7> [426.861827] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.895076] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.895420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [426.895666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [426.895975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [426.896208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.896142] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.896435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.896544] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.896651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [426.896965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [426.896919] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.897190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.897396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.897598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [426.897848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [426.898101] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [426.898486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [426.898836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [426.899142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.899428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [426.899706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [426.900759] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.901075] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.912108] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [426.945068] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [426.945398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597

<7> [426.945660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293

<7> [426.945948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161

<7> [426.946147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.946087] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [426.946344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.946438] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [426.946543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.946805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.946770] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [426.947005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.947210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [426.947395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [426.947578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [426.947792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [426.947973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [426.948174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [426.948399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [426.948623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [426.949393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [426.949675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [426.949991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [426.950266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [426.950526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [426.951374] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [426.951719] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [426.961431] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A]

<7> [426.961869] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [426.962026] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [426.979002] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.011720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.012025] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [427.012263] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [427.012466] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [427.012663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.012934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [427.013137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [427.013087] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.013353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [427.013467] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.013577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [427.013815] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.013892] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [427.014198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [427.014459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [427.014723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [427.015018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [427.015757] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.016063] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.061835] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.062207] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.062601] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [427.063010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [427.063151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.063273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [427.063525] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [427.063628] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.063825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.064123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.064107] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.064361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.064592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.064865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.065078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [427.065304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [427.065522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [427.065807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [427.066146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [427.066487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [427.066865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [427.067211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [427.067558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [427.068669] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.069079] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.078082] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [427.095790] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.096122] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.128364] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.128640] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.128959] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [427.128996] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.129195] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [427.129386] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [427.129343] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.129569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [427.129635] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.129786] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.129966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [427.130152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [427.130363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [427.130543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.130737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.130916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.131091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.131316] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [427.131625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [427.131940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [427.132246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [427.132505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [427.132810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [427.133762] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.134053] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.145310] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.145549] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.178710] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:469]

<7> [427.178820] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.179217] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.179559] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.201060] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.201378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [427.201580] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [427.201833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [427.202034] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [427.202229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.202418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.202622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.202878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.203046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [427.203209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.203373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.203531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.203752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [427.204028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [427.204297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [427.204563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [427.204840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [427.205080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [427.206127] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.206358] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.206888] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [427.207076] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [427.212196] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.245092] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.245447] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [427.245834] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [427.245958] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.246093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [427.246329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.246394] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.246563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [427.246860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [427.246814] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.247109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [427.247412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [427.247987] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.248298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [427.248542] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [427.248822] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [427.249085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.249319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [427.249567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [427.249859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [427.250147] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [427.250524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [427.250917] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [427.251300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [427.251648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [427.252080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [427.253214] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.253576] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.295147] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.295585] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.295955] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.295985] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.296305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [427.296420] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.296552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [427.296833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [427.296842] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.297063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [427.297294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.297517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.297813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.298083] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.298313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.298549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [427.298815] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [427.299019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [427.299315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [427.299622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [427.299974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [427.300354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [427.300730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [427.301077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [427.302233] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.302576] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.311390] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [427.329057] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.329352] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.361693] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.361963] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.362222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [427.362480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [427.362725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [427.362927] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [427.362878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.363123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.363252] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.363314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [427.363510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [427.363578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.363727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [427.363917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.364112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.364308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.364496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.364746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [427.365309] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.365563] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.366307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [427.366507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [427.366711] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [427.366925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [427.367159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.367373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [427.367559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [427.367788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [427.368003] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.368173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.368356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.368523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.368733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [427.369003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [427.369278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [427.369539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [427.369868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [427.370146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [427.371104] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.371412] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.378608] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.378832] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.412241] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:470]

<7> [427.412711] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.413151] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.413490] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.434320] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.434688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [427.434906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [427.435112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [427.435308] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [427.435501] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.435718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [427.435897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [427.436102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [427.436291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [427.436487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.436714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.436909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.437131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [427.437409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [427.437695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [427.437940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [427.438187] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [427.438417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [427.439312] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.439545] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.440111] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [427.440286] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [427.445559] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.478327] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.478702] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [427.478818] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.479021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [427.479274] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [427.479252] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.479514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.479630] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.479812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [427.480125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [427.480389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [427.480710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [427.481096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [427.481467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [427.481870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [427.482235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [427.482614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [427.483853] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.484295] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.528502] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.528956] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.529377] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [427.529738] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [427.529872] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.530019] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [427.530293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [427.530392] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.530561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.530935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [427.530903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.531196] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [427.531454] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [427.531744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.532002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [427.532224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [427.532445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [427.532745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [427.533149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [427.533547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [427.533995] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [427.534454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [427.534900] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [427.536447] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.536930] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.544692] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [427.562192] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.562451] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.594971] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.595261] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.595544] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [427.595902] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [427.596106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [427.596060] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.596305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [427.596433] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.596498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.596784] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [427.596798] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.596969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [427.597157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [427.597354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.597533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [427.597761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [427.597956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [427.598180] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [427.598497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [427.598830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [427.599117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [427.599404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [427.599714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [427.600775] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.601093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.611940] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.612149] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.644974] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.645346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597

<7> [427.645577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293

<7> [427.645871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161

<7> [427.645934] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.646082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [427.646282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.646309] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.646475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.646695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.646674] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.646880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.647068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [427.647304] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.647493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.647694] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.647933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [427.648247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [427.648558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [427.648908] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [427.649203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [427.649482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [427.650387] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.650735] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.651552] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [427.651882] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [427.661984] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.694952] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.695297] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [427.695573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [427.695898] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [427.696117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.696040] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.696322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [427.696419] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.696521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [427.696808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [427.696776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.697039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [427.697321] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [427.697593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [427.697935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [427.698275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [427.698606] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [427.699433] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.699774] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.745071] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.745514] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.745862] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.746005] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.746141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [427.746334] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [427.746359] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.746517] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [427.746728] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [427.746679] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.746899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.747060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.747233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.747421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.747587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.747846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [427.748026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [427.748222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [427.748435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [427.748738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [427.749028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [427.749313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [427.749668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [427.749946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [427.750945] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.751291] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.761305] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [427.779023] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.779359] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.811731] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.812026] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.812269] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [427.812474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [427.812712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [427.812891] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [427.812841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.813066] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.813235] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [427.813199] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.813404] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [427.813476] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.813623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [427.813799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.813984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.814171] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.814358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.814569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [427.814907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [427.815191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [427.815479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [427.815783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [427.816048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [427.816887] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.817193] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.828712] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.828924] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.869015] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:471]

<7> [427.868784] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.869292] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.869729] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.892842] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.893320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [427.893585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [427.893857] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [427.894083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [427.894298] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.894508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.894776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.894981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.895182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [427.895380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.895578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.895794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.896050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [427.896767] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.897027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [427.897219] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [427.897398] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [427.897573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [427.897758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.897936] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.898099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.898258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.898418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [427.898567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.898733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.898883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [427.899043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [427.899284] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [427.899516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [427.899744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [427.899961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [427.900165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [427.901378] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.901588] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.902095] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [427.902244] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [427.911967] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.945133] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.945659] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.945730] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [427.946178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [427.946173] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.946528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [427.946647] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.946951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.947294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [427.947690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [427.948044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [427.948489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [427.949032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [427.949450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [427.949955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [427.950427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [427.950870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [427.952156] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [427.952677] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [427.995288] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [427.995780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [427.995772] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [427.996235] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [427.996324] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [427.996529] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [427.996877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [427.996831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [427.997146] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [427.997462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.997772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [427.998038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [427.998288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [427.998530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [427.998840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [427.999181] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [427.999418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [427.999749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [428.000139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [428.000569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [428.001055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [428.001472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [428.001882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [428.003286] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.003705] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.011260] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [428.028419] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.028774] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.061648] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.061978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.062307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [428.062676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [428.062818] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.062918] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [428.063151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [428.063250] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.063384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.063660] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.063702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [428.063949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [428.064172] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [428.064395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.064641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [428.064870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [428.065109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [428.065432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [428.065844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [428.066173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [428.066496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [428.066885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [428.067223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [428.068331] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.068688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.078544] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.078798] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.112233] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:472]

<7> [428.112758] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.113278] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.113736] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.133539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.134122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [428.134430] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [428.134714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [428.134945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [428.135178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.135394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.135771] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [428.136019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [428.136256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [428.136454] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.136683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.136878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.137096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [428.137385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [428.137684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [428.138004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [428.138253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [428.138488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [428.139359] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.139615] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.140189] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [428.140390] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [428.145450] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.178207] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.178524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [428.178900] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [428.178897] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.179139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [428.179276] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.179365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.179604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.179663] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.179828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [428.180115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [428.180417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [428.180812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [428.181226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [428.181621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [428.182077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [428.182478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [428.183560] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.184023] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.228339] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.228728] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.228834] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.229049] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [428.229261] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [428.229210] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.229460] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [428.229523] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.229689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [428.229880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.230069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.230270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [428.230488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [428.230726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.230890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.231052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [428.231250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [428.231485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [428.231812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [428.232100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [428.232381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [428.232726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [428.233042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [428.234293] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.234640] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.244576] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [428.262098] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.262393] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.295066] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.295398] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.295796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [428.295877] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.296078] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [428.296321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [428.296309] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.296582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [428.296717] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.296814] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.297067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.297306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [428.297520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [428.297794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.298018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.298259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [428.298525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [428.298870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [428.299183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [428.299482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [428.299824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [428.300189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [428.300506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [428.301686] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.302026] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.311973] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.312170] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.345069] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.345384] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823

<7> [428.345673] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614

<7> [428.345796] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.345920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614

<7> [428.346155] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [428.346229] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.346382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.346641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [428.346634] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.346865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [428.347068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [428.347265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.347456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [428.347697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [428.347890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [428.348089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.348286] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [428.348482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [428.348777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [428.348970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [428.349156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.349340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.349520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.349805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [428.350121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [428.350454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [428.350820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [428.351146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [428.351416] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [428.352322] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.352614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.353360] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [428.353647] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [428.361838] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.394816] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.395082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [428.395321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [428.395516] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [428.395757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.395948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [428.395882] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.396134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [428.396230] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.396341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [428.396519] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.396567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [428.397017] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.397224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [428.397390] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [428.397569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [428.397731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.397895] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [428.398064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [428.398232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [428.398412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [428.398710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [428.398962] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [428.399210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [428.399451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [428.399764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [428.400426] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.400734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.444866] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.445148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.445408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [428.445698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [428.445812] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.445887] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [428.446068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [428.446160] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.446247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.446419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [428.446463] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.446620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [428.446791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [428.446981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.447144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [428.447306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [428.447465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [428.447698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [428.448166] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.448365] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.448581] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [428.448741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [428.448895] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [428.449042] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [428.449189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.449358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [428.449508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [428.449706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [428.449854] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.449996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [428.450138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [428.450280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [428.450427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [428.450706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [428.450969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [428.451211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [428.451497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [428.451779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [428.452561] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.452816] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.461202] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [428.478496] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.478772] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.511502] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.511841] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.512108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [428.512359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [428.512582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [428.512708] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.512771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [428.512995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.513059] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.513190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [428.513365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [428.513355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.513559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [428.513729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.513886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [428.514045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [428.514204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [428.514393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [428.514678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [428.514932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [428.515192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [428.515446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [428.516123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [428.516919] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.517206] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.528425] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.528732] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.561451] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.561749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823

<7> [428.561949] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614

<7> [428.562141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614

<7> [428.562325] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [428.562504] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.562741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [428.562922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [428.562870] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.563103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [428.563276] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [428.563218] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.563446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.563517] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.563663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.563862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.564061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [428.564326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [428.564601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [428.564914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [428.565166] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [428.565410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [428.566449] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.566741] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.567306] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [428.567548] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [428.578333] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.611476] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.611791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [428.612002] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [428.612204] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [428.612398] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.612690] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [428.612807] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.612925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [428.613141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [428.613204] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.613370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [428.613516] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.613701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [428.614026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [428.614297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [428.614573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [428.614864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [428.615573] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.615847] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.661564] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.661889] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.662248] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [428.662481] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [428.662761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [428.662946] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [428.662891] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.663125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.663244] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.663301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [428.663491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [428.663578] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.663751] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [428.663926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.664095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [428.664261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [428.664426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [428.664660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [428.664933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [428.665197] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [428.665515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [428.665831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [428.666089] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [428.667242] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.667561] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.677810] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [428.695396] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.695742] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.728101] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.728350] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.728649] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [428.728636] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.728875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [428.728992] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.729064] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [428.729248] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [428.729286] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.729430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.729644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [428.729839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [428.730006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [428.730175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.730341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [428.730505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [428.730769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [428.730989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [428.731261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [428.731537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [428.731801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [428.732073] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [428.732373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [428.733359] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.733665] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.745113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.745333] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.778336] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.778635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826

<7> [428.778735] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.778830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605

<7> [428.779012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620

<7> [428.779063] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.779192] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [428.779332] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.779369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.779572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.779749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [428.779956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [428.780145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [428.780314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.780481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.780725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.780928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [428.781179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [428.781425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [428.781715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [428.781952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [428.782184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [428.783058] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.783315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.783976] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [428.784198] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [428.795104] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.828130] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.828410] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [428.828673] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289

<7> [428.828860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164

<7> [428.828809] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.829040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.829134] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.829217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.829392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [428.829405] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.829639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [428.829844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [428.830234] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.830438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [428.830638] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289

<7> [428.830799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164

<7> [428.830964] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.831125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.831295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [428.831487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [428.831707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [428.831971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [428.832234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [428.832530] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [428.832788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [428.833026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [428.833891] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.834155] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.878127] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.878554] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.878662] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.878902] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.878924] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.879222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913

<7> [428.879202] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.879426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452

<7> [428.879651] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794

<7> [428.879832] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892

<7> [428.880009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.880183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.880355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [428.880589] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [428.880757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.880918] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.881079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [428.881273] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [428.881486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [428.881801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [428.882069] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [428.882335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [428.882624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [428.882932] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [428.883978] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.884256] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.894465] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [428.911871] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.912131] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.944781] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.945046] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.945325] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691

<7> [428.945612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676

<7> [428.945643] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.945827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350

<7> [428.946026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334

<7> [428.946015] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.946225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.946326] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.946420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.946656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [428.946860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [428.947076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.947267] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.947442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [428.947662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [428.947885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [428.948369] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.948597] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.948803] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691

<7> [428.948994] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676

<7> [428.949168] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350

<7> [428.949322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334

<7> [428.949474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.949680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.949843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [428.950004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [428.950166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.950360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [428.950555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [428.950717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [428.950889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [428.951137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [428.951380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [428.951663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [428.951919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [428.952173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [428.953066] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [428.953321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [428.961699] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.961901] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [428.994747] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [428.995030] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 691) -> ( 0 - 823), size 691 -> 823

<7> [428.995244] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 691 - 1367) -> ( 823 - 2437), size 676 -> 1614

<7> [428.995451] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2717) -> (2437 - 4051), size 1350 -> 1614

<7> [428.995722] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0

<7> [428.995908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [428.995854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [428.996131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [428.996206] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [428.996326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [428.996561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [428.996540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [428.996745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [428.996929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.997114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.997300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [428.997539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [428.997835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [428.998123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [428.998404] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [428.998760] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [428.999009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [428.999758] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.000048] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.000860] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [429.001137] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [429.011604] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.044747] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.045073] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [429.045355] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [429.045641] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [429.045772] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.045859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.046063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.046146] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.046266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.046528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.046458] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.046764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [429.047042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [429.047309] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [429.047592] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [429.047856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [429.048121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [429.048804] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.049113] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.094778] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.095080] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.095422] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [429.095715] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [429.095910] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [429.095841] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.096095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [429.096191] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.096279] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.096459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.096521] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.096740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.096925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.097102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.097260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [429.097414] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [429.097600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [429.097788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [429.098058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [429.098322] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [429.098619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [429.098921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [429.099163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [429.099976] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.100256] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.111097] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [429.128433] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.128747] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.161355] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.161627] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.161870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [429.162079] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [429.162263] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [429.162442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [429.162688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.162869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.162800] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.163048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.163145] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.163262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.163465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.163446] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.163692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.163862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.164030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.164223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [429.164494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [429.164748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [429.165003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [429.165258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [429.165576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [429.166416] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.166736] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.178308] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.178581] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.211349] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.211667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823

<7> [429.211922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614

<7> [429.212126] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614

<7> [429.212319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [429.212549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.212743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.212675] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.212931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.213044] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.213160] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.213380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [429.213366] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.213639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.213847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.214032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.214233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [429.214520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [429.214792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [429.215057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [429.215312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [429.215608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [429.216679] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.216960] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.217594] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [429.217825] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [429.228541] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.261792] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.262376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [429.262821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [429.262838] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.263134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [429.263434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.263401] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.263776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.263936] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.264085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.264372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.264765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [429.265591] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.265969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [429.266261] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [429.266582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [429.266864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.267146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.267425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.267728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.268031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [429.268516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [429.268963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [429.269388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [429.269834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [429.270271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [429.271934] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.272369] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.311739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.312281] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.312670] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.312640] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.313033] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [429.313042] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.313304] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [429.313413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.313593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [429.313847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [429.314095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.314346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.314630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.314876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.315115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.315359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [429.315622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [429.315867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [429.316175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [429.316628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [429.317023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [429.317413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [429.317845] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [429.318243] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [429.320187] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.320634] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.327703] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [429.346848] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.347209] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.378508] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.378633] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.378954] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.379025] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.379346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.379439] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [429.379762] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [429.380025] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [429.380273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [429.380546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.380793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.381042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.381291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.381581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.381830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.382074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.382316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.382645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [429.383071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [429.383492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [429.383883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [429.384276] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [429.384706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [429.386638] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.387076] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.395444] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.395703] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.428503] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.428658] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.428990] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.429117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826

<7> [429.429438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605

<7> [429.429403] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.429789] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620

<7> [429.430074] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [429.430346] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.430643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [429.430896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [429.431140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [429.431386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [429.431653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.431902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.432144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.432468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [429.433321] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.433706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826

<7> [429.433963] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605

<7> [429.434210] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620

<7> [429.434470] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [429.434711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.434957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [429.435203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [429.435475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [429.435726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [429.435964] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.436204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.436443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.436728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [429.437141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [429.437562] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [429.437925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [429.438280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [429.438637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [429.440070] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.440375] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.441167] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [429.441396] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [429.445285] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.478304] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.478800] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.478891] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [429.479210] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289

<7> [429.479296] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.479537] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164

<7> [429.479820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.479773] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.480098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [429.480375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [429.480685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [429.481024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [429.481522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [429.481966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [429.482401] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [429.482856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [429.483282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [429.484836] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.485275] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.528177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.528549] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.528531] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.528882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913

<7> [429.528893] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.529122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452

<7> [429.529226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.529347] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794

<7> [429.529578] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892

<7> [429.529801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.530025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [429.530247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [429.530491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [429.530720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.530933] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [429.531146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [429.531359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [429.531660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [429.532013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [429.532354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [429.532701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [429.533052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [429.533399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [429.535186] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.535601] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.544326] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [429.562369] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.562741] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.594933] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.595346] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.595749] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.595821] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691

<7> [429.596127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676

<7> [429.596178] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.596413] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350

<7> [429.596613] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.596717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334

<7> [429.596989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.597264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [429.597567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [429.597843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [429.598112] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.598372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [429.598684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [429.598950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [429.599279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [429.599781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [429.600231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [429.600693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [429.601130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [429.601585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [429.603637] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.604104] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.611959] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [429.612214] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [429.644796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 691) -> ( 0 - 2026), size 691 -> 2026

<7> [429.645126] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 691 - 1367) -> (2026 - 4051), size 676 -> 2025

<7> [429.645421] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2717) -> ( 0 - 0), size 1350 -> 0

<7> [429.645800] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0

<7> [429.645943] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.646056] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.646359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.646414] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.646678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.646907] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.646948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.647234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.647502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.647736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.647969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.648194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [429.648422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.648728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.648972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.649198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [429.649418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.649714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.649985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.650281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [429.650732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [429.651141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [429.651473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [429.651788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [429.652075] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [429.652957] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.653259] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.653943] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [429.654189] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A]

<7> [429.677970] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [429.678247] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [429.678540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.678674] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.678765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.678981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.679089] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.679202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.679462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [429.679467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.679755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [429.680050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [429.680347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [429.680728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [429.681018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [429.681658] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.681915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.711300] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [429.711617] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [429.711713] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.711875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [429.712076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [429.712113] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.712269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.712486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.712482] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.712680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.712930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.713140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.713338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [429.713581] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [429.713798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [429.714046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [429.714374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [429.714771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [429.715098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [429.715414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [429.715776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [429.716647] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.716942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.728070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [429.761294] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [429.761638] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [429.761727] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.761912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [429.762108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [429.762085] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.762297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.762385] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.762517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.762701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.762921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.763122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.763293] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.763497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.763670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.763870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [429.764298] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [429.764583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [429.764766] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [429.764937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [429.765101] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.765268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.765867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.766045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.766202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.766356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.766550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.766713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.766902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [429.767173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [429.767476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [429.767738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [429.767999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [429.768238] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [429.769084] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.769359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.778148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [429.811361] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [429.811709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [429.811839] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.811933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [429.812141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.812207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.812345] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.812588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.812563] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.812785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.812972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [429.813184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.813384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.813637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.813837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [429.814223] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [429.814406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [429.814636] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [429.814808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.815022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.815187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.815354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.815558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [429.815719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.815911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.816070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.816239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [429.816528] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [429.816784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [429.817039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [429.817288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [429.817569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [429.818317] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.818623] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.844666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [429.844947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [429.845209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.845494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.845643] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.845730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.845994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.846052] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.846251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [429.846396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.846723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [429.846916] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [429.847102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.847312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.847531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.847703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.847874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [429.848246] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [429.848439] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [429.848593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.848744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.848906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.849079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.849244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [429.849541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [429.849757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [429.849968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [429.850165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [429.850387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [429.851034] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.851237] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.877911] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [429.878227] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [429.878548] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [429.878559] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.878750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [429.878939] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.878909] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.879113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.879187] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.879284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.879490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.879659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.879825] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [429.879993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [429.880158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [429.880347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [429.880809] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [429.881011] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [429.881162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [429.881307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [429.881564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.881723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.881890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.882036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.882171] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.882295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [429.882480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [429.882606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [429.882732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [429.882958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [429.883152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [429.883335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [429.883539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [429.883712] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [429.884536] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.884709] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.895040] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [429.927929] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [429.928278] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [429.928668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [429.928810] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.928901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [429.929125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.929206] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.929396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [429.929601] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.929679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [429.929879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [429.930114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.930313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [429.930599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [429.930804] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [429.931023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [429.931295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [429.931587] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [429.931866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [429.932143] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [429.932427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [429.933464] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.933746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [429.944768] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [429.978180] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [429.978453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [429.978468] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [429.978665] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [429.978807] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [429.978857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [429.979037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [429.979090] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [429.979215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [429.979439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [429.979632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [429.979823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.980001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.980175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [429.980381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [429.980698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [429.980953] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [429.981210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [429.981468] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [429.981715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [429.982598] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [429.982866] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.011244] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [430.011524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [430.011728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.011670] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.011927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.012013] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.012123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [430.012304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.012355] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [430.012637] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [430.012951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [430.013206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [430.013471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.013717] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.013975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [430.014809] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.015085] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.044610] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.044870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [430.045067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [430.045254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [430.045488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.045674] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.045631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.045873] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [430.046003] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.046088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [430.046261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.046324] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.046466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.046637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [430.046800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [430.046983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [430.047248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [430.047547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [430.047804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [430.048058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [430.048304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [430.049272] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.049593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.061423] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.094567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.094862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [430.095123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [430.095322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [430.095582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.095712] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.095780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.095974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [430.096060] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.096202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [430.096352] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.096427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.096610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.096788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [430.096991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [430.097210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [430.097485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [430.097739] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [430.097997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.098286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.098565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [430.099663] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.099956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.111468] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.144550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026

<7> [430.144784] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025

<7> [430.144990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [430.145187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.145376] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.145633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.145828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.145766] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.146011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [430.146110] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.146193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.146369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.146437] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.146651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.146884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [430.147190] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [430.147486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [430.147747] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [430.148005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [430.148261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [430.148972] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.149249] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.177881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [430.178141] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [430.178361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.178651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.178763] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.178864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.179064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.179113] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.179271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [430.179442] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.179574] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [430.179838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [430.180082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.180368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.180660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [430.181408] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.181684] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.211213] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.211524] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [430.211647] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.211752] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [430.211954] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [430.212033] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.212156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.212354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.212368] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.212619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.212820] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.213017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.213190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [430.213364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [430.213599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [430.213793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [430.214180] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.214434] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [430.214630] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [430.214789] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [430.214942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.215097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.215255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.215447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.215621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.215789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [430.215942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [430.216092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [430.216281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [430.216591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [430.216853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [430.217110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [430.217358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [430.217705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [430.218553] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.218820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.228006] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.261214] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.261520] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [430.261742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [430.261815] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.261942] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [430.262135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.262160] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.262323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.262473] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.262555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.262744] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.262925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.263100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.263275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.263480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.263683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [430.264057] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.264279] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [430.264503] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [430.264677] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [430.264845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.265055] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.265248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.265464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.265638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.265808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.265988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.266168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.266359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [430.266714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [430.267033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [430.267348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.267718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.268071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [430.269094] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.269424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.277979] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.311198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [430.311488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [430.311615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.311708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [430.311916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.311982] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.312108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.312275] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.312295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.312564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.312747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [430.312920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.313088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.313252] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.313473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [430.313939] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [430.314118] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [430.314288] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [430.314495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.314666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.314861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.315041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.315218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [430.315410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.315582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.315753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.315927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [430.316196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [430.316490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [430.316792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [430.317035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [430.317277] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [430.317993] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.318264] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.344566] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [430.344820] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [430.345024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.345214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.345443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.345630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.345582] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.345876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [430.345933] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.346142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [430.346211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.346414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [430.346664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.346984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.347279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [430.348043] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.348305] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.377815] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.378072] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [430.378259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [430.378480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [430.378657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.378623] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.378826] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.379005] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.378974] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.379167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.379275] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.379326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.379535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [430.379695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [430.379846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [430.380016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [430.380263] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [430.380537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [430.380785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [430.381025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [430.381260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [430.382178] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.382462] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.394583] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.427793] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.428039] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [430.428221] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [430.428445] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [430.428622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.428576] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.428793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.428917] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.428967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.429156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.429200] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.429307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.429507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.429659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.429808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.429983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [430.430231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [430.430507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [430.430752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.430990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.431275] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [430.432242] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.432535] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.444612] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.477951] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [430.478137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [430.478305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [430.478530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.478695] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.478664] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.478857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [430.478997] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.479059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [430.479242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [430.479298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.479436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.479603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.479770] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.479954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [430.480210] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [430.480487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [430.480733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [430.480979] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [430.481240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [430.481929] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.482184] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.511159] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [430.511377] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [430.511555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.511513] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.511729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.511899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [430.511859] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.512098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [430.512157] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.512301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [430.512599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [430.512853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [430.513132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.513402] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.513643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [430.514384] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.514632] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.544460] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.544677] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [430.544853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [430.545027] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [430.545195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.545392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.545575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [430.545523] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.545778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [430.545866] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.545957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.546152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.546160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.546334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [430.546547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [430.546733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [430.546977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [430.547216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [430.547484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [430.547726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [430.547974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [430.548927] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.549181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.561337] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.594452] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.594725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [430.594956] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [430.595157] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [430.595378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.595570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.595504] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.595754] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [430.595848] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.595968] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [430.596161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.596135] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.596324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [430.596545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [430.596709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [430.596899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [430.597160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [430.597423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [430.597714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.597951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.598185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [430.599142] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.599416] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.611326] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.644468] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691

<7> [430.644689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360

<7> [430.644881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [430.645065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.645244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.645472] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.645583] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.645651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.645836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.645908] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.646024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.646191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.646181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.646377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.646543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [430.646703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.646864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.647025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.647220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [430.647626] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691

<7> [430.647797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360

<7> [430.647958] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [430.648117] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.648305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.648531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.648688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.648840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.648990] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.649138] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.649283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.649475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [430.649646] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.649798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.649948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.650111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [430.650427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [430.650686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [430.650966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.651223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.651544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [430.652345] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.652619] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.694522] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [430.694802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [430.695013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.695205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.695442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.695555] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.695627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.695877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [430.695904] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.696184] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.696257] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [430.696476] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [430.696643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.696802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.696961] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.697147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.697361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [430.697622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [430.697869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [430.698113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.698365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.698619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [430.699249] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.699535] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.728473] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.728677] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:473]

<7> [430.728844] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.729132] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.748305] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.748676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [430.748899] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [430.749110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [430.749319] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.749740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.749943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.750182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.750647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.750833] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [430.751032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [430.751231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [430.751549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [430.751939] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.752153] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [430.752334] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [430.752501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [430.752664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.752827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.753022] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.753211] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.753430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.753586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [430.753740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [430.753894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [430.754064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [430.754318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [430.754770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [430.755000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [430.755224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [430.755540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [430.756247] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.756479] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.761301] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.794472] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.794784] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [430.795054] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [430.795260] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [430.795532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.795655] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.795733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.795929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.796030] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.796145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.796349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.796373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.796535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.796719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.796902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.797135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [430.797694] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.797932] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [430.798121] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [430.798306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [430.798550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.798741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.798975] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.799191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.799437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.799623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.799809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.800014] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.800216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [430.800527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [430.800812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [430.801096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [430.801361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [430.801669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [430.802582] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.802867] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.811221] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.844547] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [430.844846] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [430.845100] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [430.845392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.845515] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.845634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.845872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.845945] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.846126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.846371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [430.846590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.846735] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.846810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.847020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [430.847271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [430.847660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [430.847998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [430.848353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.848740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [430.849074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [430.849943] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.850262] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.877800] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [430.878082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [430.878360] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.878490] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.878593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.878815] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.878887] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.879062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.879206] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.879341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [430.879654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [430.879929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [430.880182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.880462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [430.880715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [430.881514] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.881790] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.911106] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.911423] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [430.911528] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.911694] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [430.911891] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [430.911913] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.912078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.912260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.912230] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.912502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.912682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.912848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.913012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [430.913179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [430.913417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [430.913624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [430.913878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [430.914128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [430.914387] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [430.914630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [430.914876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [430.915933] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.916192] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.927902] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.961090] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [430.961395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [430.961496] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [430.961606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [430.961798] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [430.961837] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [430.961978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.962111] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [430.962153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [430.962350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [430.962528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [430.962734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [430.962926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [430.963097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [430.963294] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [430.963541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [430.963850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [430.964106] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [430.964371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [430.964615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [430.964854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [430.965834] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [430.966092] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [430.977927] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.011212] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [431.011478] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [431.011605] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.011672] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [431.011859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.011939] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.012050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.012237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [431.012237] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.012525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [431.012728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [431.012919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.013094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.013271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.013532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [431.013817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [431.014081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [431.014359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [431.014623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [431.014883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [431.015637] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.015921] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.044450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [431.044646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [431.044827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.045004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.045179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [431.045444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [431.045459] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.045653] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [431.045803] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.045922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [431.046114] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.046196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [431.046498] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [431.046770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [431.047076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [431.047910] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.048223] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.077728] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.077985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [431.078210] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [431.078458] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [431.078653] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.078607] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.078843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.078967] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.079033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [431.079206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [431.079257] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.079408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.079576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.079741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [431.079889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [431.080064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [431.080320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [431.080565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [431.080805] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.081082] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.081348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [431.082265] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.082574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.094539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.127780] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.128053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [431.128252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [431.128514] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [431.128707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.128647] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.128896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.129025] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.129086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [431.129281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [431.129344] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.129507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.129673] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.129860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [431.130030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [431.130223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [431.130621] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.130853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [431.131021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [431.131186] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [431.131382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.131579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.131763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [431.131940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [431.132094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.132246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.132456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [431.132611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [431.132766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [431.133003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [431.133239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [431.133505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [431.133744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [431.134067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [431.135064] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.135353] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.144659] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.177795] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691

<7> [431.178052] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360

<7> [431.178274] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0

<7> [431.178562] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.178694] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.178773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.178986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.179053] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.179210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.179378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.179484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [431.179672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.179861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.180024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.180213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [431.180632] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691

<7> [431.180811] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360

<7> [431.180989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0

<7> [431.181161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.181386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.181558] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.181724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.181888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [431.182049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.182209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.182408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.182580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [431.182837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [431.183076] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [431.183324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [431.183609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [431.183840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [431.184508] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.184762] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.211069] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [431.211347] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [431.211560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.211503] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.211755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [431.211844] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.211931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [431.212120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [431.212113] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.212331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [431.212693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [431.212873] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [431.213047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.213216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [431.213429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [431.213608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [431.213782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [431.214139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [431.214346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [431.214498] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.214649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [431.214807] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [431.214995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [431.215191] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [431.215492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [431.215761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [431.216025] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [431.216273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [431.216559] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [431.217253] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.217539] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.244458] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.244813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [431.245057] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [431.245327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [431.245548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.245468] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.245761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.245870] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.245988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.246263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.246242] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.246549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.246767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [431.246970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [431.247162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [431.247435] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [431.248002] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.248258] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [431.248513] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [431.248712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [431.248919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.249098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.249295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.249491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.249691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.249876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [431.250060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [431.250226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [431.250456] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [431.250738] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [431.251011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [431.251265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.251550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.251836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [431.252659] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.252905] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.261092] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.294386] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.294706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [431.294963] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [431.295164] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [431.295400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.295587] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [431.295546] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.295775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [431.295896] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.295983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [431.296172] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.296175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.296422] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.296614] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.296792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.296998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [431.297269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [431.297578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [431.297913] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [431.298185] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [431.298534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [431.299445] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.299743] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.311215] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.344427] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [431.344709] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [431.344945] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [431.345170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.345450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.345575] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.345671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.345894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.345985] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.346104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [431.346333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.346355] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.346537] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.346755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.346997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [431.347329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [431.347687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [431.348011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [431.348344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [431.348694] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [431.349494] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.349808] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.377747] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [431.378063] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [431.378395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.378534] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.378642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [431.378875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [431.378979] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.379140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [431.379361] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.379424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [431.379746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [431.380078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [431.380412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [431.380770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [431.381070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [431.382007] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.382356] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.411047] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.411426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [431.411475] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.411644] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [431.411835] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [431.411864] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.412018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.412218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.412182] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.412465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.412645] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.412818] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.412986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [431.413158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [431.413384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [431.413599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [431.413885] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [431.414177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [431.414501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.414853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.415155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [431.416295] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.416611] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.427945] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.461006] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.461366] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [431.461460] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.461596] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [431.461799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [431.461823] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.461994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.462137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.462186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [431.462427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [431.462618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [431.462845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.463029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.463203] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.463453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.463665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [431.463937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [431.464206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [431.464496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [431.464812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [431.465086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [431.466170] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.466485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.477931] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.511175] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [431.511496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [431.511617] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.511721] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [431.511916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.511971] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.512105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.512330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [431.512314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.512533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [431.512755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [431.512929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.513105] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.513299] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.513508] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [431.513791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [431.514085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [431.514403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [431.514685] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [431.514968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [431.515831] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.516116] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.544378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [431.544636] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [431.544844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.545035] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.545219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [431.545530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [431.545660] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.545764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [431.546013] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.546048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [431.546329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [431.546335] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.546600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [431.546866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [431.547130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [431.547978] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.548244] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.577652] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.577922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [431.578146] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [431.578388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [431.578565] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.578538] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.578739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.578883] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.578940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [431.579107] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [431.579160] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.579296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.579449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.579604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [431.579757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [431.579937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [431.580361] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.580611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [431.580777] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [431.580946] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [431.581094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.581239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.581456] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [431.581629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [431.581778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.581926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.582075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [431.582225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [431.582453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [431.582727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [431.582993] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [431.583261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.583526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.583768] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [431.584787] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.585081] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.594533] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.627681] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.627978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [431.628218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [431.628497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [431.628693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.628640] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.628879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.628982] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.629079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [431.629318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [431.629298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.629507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.629683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.629881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [431.630059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [431.630278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [431.630690] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.630922] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [431.631111] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [431.631320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [431.631493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.631662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.631840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [431.632037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [431.632195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.632410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.632572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [431.632727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [431.632895] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [431.633206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [431.633518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [431.633823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [431.634091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [431.634366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [431.635414] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.635706] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.644486] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [431.677606] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.677898] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597

<7> [431.678108] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293

<7> [431.678359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161

<7> [431.678554] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.678496] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.678742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.678848] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.678925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.679114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.679137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.679314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.679491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.679702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.679919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.680093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.680285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.680467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [431.680642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [431.680855] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [431.681308] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.681530] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597

<7> [431.681698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293

<7> [431.681868] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161

<7> [431.682046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.682259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.682427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.682586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.682748] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.682921] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.683086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.683277] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.683438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.683593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [431.683749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [431.683906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [431.684077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [431.684374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [431.684645] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [431.684935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [431.685194] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [431.685480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [431.686493] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.686755] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.694012] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A]

<7> [431.694531] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [431.694666] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [431.711374] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.744282] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.744541] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [431.744725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [431.744904] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [431.745087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.745320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [431.745505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [431.745448] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.745724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [431.745799] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.745966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [431.746103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.746265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [431.746542] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [431.746827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.747084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.747421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [431.748168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.748937] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.794418] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.794773] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [431.795113] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [431.795432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [431.795669] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [431.795590] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.795896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [431.796022] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.796120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.796432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.796444] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.796668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.796882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.797076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.797296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [431.797503] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [431.797713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [431.797959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [431.798314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [431.798658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [431.798981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [431.799304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [431.799644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [431.800940] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.801293] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.810682] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [431.828198] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.828513] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [431.860946] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.861188] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [431.861504] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [431.861619] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.861742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [431.861943] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [431.861980] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.862142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [431.862380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.862335] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.862579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [431.862782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [431.863016] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [431.863207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.863462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.863664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.863902] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.864158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [431.864535] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [431.864893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [431.865179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [431.865500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [431.865844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [431.867069] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.867409] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.877955] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.878156] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [431.910960] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.911306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [431.911380] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.911589] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [431.911810] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [431.911782] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.912021] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [431.912126] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.912265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.912478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [431.912686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [431.912938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [431.913135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [431.913372] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.913570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.913766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [431.914007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [431.914357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [431.914663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [431.914974] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [431.915301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [431.915639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [431.916815] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.917118] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [431.917817] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [431.918075] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [431.927876] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.961004] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [431.961401] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [431.961498] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [431.961666] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [431.961915] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [431.961928] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [431.962157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [431.962344] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [431.962447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [431.962687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [431.962923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [431.963176] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [431.963551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [431.963929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [431.964260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.964616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [431.964933] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [431.965846] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [431.966181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.011082] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.011482] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.011819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [432.012106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [432.012408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [432.012636] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [432.012568] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.012857] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.013073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.013006] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.013324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.013427] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.013572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.013779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.013984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [432.014188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [432.014458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [432.014698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [432.015033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [432.015397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [432.015784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [432.016126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [432.016493] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [432.017986] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.018380] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.027295] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [432.044923] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.045267] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.077696] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.077957] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.078252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [432.078397] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.078489] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [432.078677] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [432.078749] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.078862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [432.079033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.079033] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.079226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [432.079410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [432.079585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [432.079753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.079925] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.080097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.080302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.080520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [432.080810] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [432.081098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [432.081412] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [432.081750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [432.082080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [432.083346] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.083649] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.094656] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.094869] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.127922] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.128272] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [432.128383] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.128543] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [432.128749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [432.128756] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.128937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [432.129060] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.129123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.129397] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.129590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [432.129766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [432.129955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [432.130121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.130332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.130512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.130762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [432.131059] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [432.131371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [432.131640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [432.131944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [432.132226] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [432.133229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.133511] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.134223] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [432.134467] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [432.144563] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.177550] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.177872] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [432.178132] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [432.178418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [432.178628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.178566] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.178830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.178925] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.179026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [432.179283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [432.179257] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.179546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [432.180043] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.180303] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [432.180515] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [432.180693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [432.180881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.181090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.181311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [432.181473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [432.181674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [432.181947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [432.182223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [432.182492] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [432.182776] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [432.183033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [432.183881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.184171] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.227663] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.228023] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.228438] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [432.228538] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.228691] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [432.228949] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [432.228998] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.229213] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [432.229459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.229460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.229704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.229941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [432.230208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [432.230439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.230660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.230885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [432.231109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [432.231443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [432.232106] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.232428] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.232701] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [432.232916] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [432.233123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [432.233395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [432.233616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.233834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.234037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [432.234260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [432.234465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.234654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.234871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [432.235086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [432.235373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [432.235726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [432.236045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [432.236405] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [432.236728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [432.237047] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [432.238432] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.238723] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.243934] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [432.261596] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.261880] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.294306] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.294604] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.294907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [432.295163] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [432.295490] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [432.295620] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.295721] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [432.295944] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.296038] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.296149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.296417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [432.296435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.296679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [432.296914] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.297116] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.297371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [432.297574] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [432.297816] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [432.298142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [432.298500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [432.298841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [432.299136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [432.299504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [432.300881] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.301226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.311265] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.311457] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.344277] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.344618] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597

<7> [432.344906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293

<7> [432.345123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161

<7> [432.345413] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [432.345456] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.345627] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.345827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.346023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.345965] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.346264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.346458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [432.346396] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.346643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.346826] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.347016] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.347228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [432.347507] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [432.347788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [432.348061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [432.348348] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [432.348660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [432.349708] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.350034] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.350937] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [432.351228] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [432.361169] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.394230] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.394533] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [432.394742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [432.394934] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [432.395113] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.395347] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [432.395370] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.395522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [432.395724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [432.395719] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.395927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [432.396033] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.396222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [432.396497] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [432.396757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [432.397001] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [432.397273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [432.397951] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.398249] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.444306] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.444609] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.444874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [432.445058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [432.445293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [432.445315] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.445466] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [432.445652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.445646] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.445816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.445989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.445953] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.446161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.446384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.446550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [432.446713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [432.446894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [432.447095] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [432.447381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [432.447631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [432.447886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [432.448149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [432.448515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [432.449524] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.449792] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.460560] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [432.478020] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.478369] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.510867] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.511155] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.511490] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [432.511480] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.511712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [432.511911] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [432.511871] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.512107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [432.512261] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.512362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.512553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [432.512745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [432.512974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [432.513207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.513410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.513597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.513779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.513994] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [432.514330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [432.514613] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [432.514886] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [432.515153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [432.515525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [432.516627] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.516922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.527805] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.528001] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.560970] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.561341] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [432.561426] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.561579] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [432.561802] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [432.561832] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.562006] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [432.562233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.562211] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.562437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.562659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.562883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.563100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [432.563336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.563530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.563706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.563902] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [432.564171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [432.564442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [432.564726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [432.565003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [432.565344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [432.566362] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.566675] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.567310] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [432.567577] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [432.577983] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.610910] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.611264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [432.611334] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.611527] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [432.611743] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [432.611752] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.611960] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.612088] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.612213] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [432.612430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [432.612661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [432.612926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [432.613421] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.613698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [432.613909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [432.614107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [432.614380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.614631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [432.614858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [432.615090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [432.615374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [432.615710] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [432.616011] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [432.616331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [432.616681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [432.616997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [432.617799] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.618099] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.660909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.661379] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.661509] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.661779] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.661800] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.662089] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [432.662093] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.662362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [432.662561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [432.662750] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [432.662983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.663192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.663377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.663550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.663731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.663940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [432.664119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [432.664363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [432.664545] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [432.664819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [432.665115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [432.665446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [432.665758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [432.666030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [432.667309] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.667632] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.677203] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [432.694674] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.694973] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.727437] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.727682] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.727912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [432.728204] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [432.728395] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [432.728346] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.728583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [432.728700] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.728768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.728956] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [432.729017] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.729209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [432.729417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [432.729644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.729850] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.730040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.730269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.730478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [432.731003] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.731279] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.731501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [432.731727] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [432.731904] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [432.732080] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [432.732344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.732539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [432.732749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [432.732908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [432.733074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.733329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.733488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.733643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.733826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [432.734129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [432.734452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [432.734757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [432.735033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [432.735298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [432.736376] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.736664] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.744567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.744762] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.777719] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.778069] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [432.778437] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [432.778561] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.778688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [432.778942] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [432.779000] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.779212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.779434] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.779518] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.779762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [432.780019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [432.780265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [432.780470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.780668] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.780892] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.781186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [432.781544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [432.781882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [432.782234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [432.782546] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [432.782882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [432.784157] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.784501] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.785300] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [432.785582] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [432.794461] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.827477] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.827833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [432.828129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [432.828469] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [432.828612] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.828715] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.828952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.829045] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.829240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [432.829535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [432.829473] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.829801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [432.830164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [432.830514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [432.830877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [432.831248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [432.831647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [432.832598] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.832952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.877631] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.878026] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.878538] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [432.878631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.878871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [432.879151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [432.879182] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.879400] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [432.879574] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.879651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.879890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.880179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [432.880419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [432.880654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.880874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.881182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [432.881437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [432.881719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [432.882098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [432.882521] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [432.882939] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [432.883380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [432.883744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [432.885325] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.885743] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.893818] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [432.911586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.911946] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.944139] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.944418] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.944679] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [432.944901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [432.945090] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [432.945343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [432.945524] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.945487] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.945710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.945848] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.945893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [432.946106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [432.946181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.946350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.946561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [432.946749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [432.946945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [432.947155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [432.947438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [432.947732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [432.948015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [432.948328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [432.948595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [432.949789] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [432.950094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [432.961143] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.961354] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [432.994192] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [432.994582] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823

<7> [432.994881] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614

<7> [432.995280] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614

<7> [432.995342] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [432.995611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [432.995866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.995820] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [432.996184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [432.996306] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [432.996438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [432.996686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [432.996927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.997244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.997495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.997755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.998032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [432.998388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [432.998643] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [432.998898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [432.999141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [432.999364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.999614] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [432.999893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.000354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [433.000773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [433.001262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [433.001629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [433.001985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [433.002373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [433.003695] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.004061] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.004995] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [433.005335] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [433.011035] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.044177] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.044554] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [433.044816] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [433.045061] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [433.045419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.045536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.045720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [433.045965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [433.045985] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.046243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [433.046405] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.046549] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [433.047056] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.047387] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [433.047623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [433.047864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [433.048140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.048426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [433.048664] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [433.048910] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [433.049149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [433.049470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [433.049789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [433.050132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [433.050449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [433.050762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [433.051649] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.051999] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.094358] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.094890] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.095296] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.095421] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.095646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [433.095947] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [433.095899] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.096241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [433.096357] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.096496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [433.096794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.097054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.097371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.097599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.097877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.098689] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [433.098949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [433.099251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [433.099582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [433.099952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [433.100390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [433.100771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [433.101231] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [433.101631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [433.103101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.103548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.110440] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [433.128240] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.128556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.160968] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.161308] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.161446] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.161594] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [433.161861] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [433.161841] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.162068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [433.162240] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.162320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [433.162510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.162732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [433.162915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [433.163163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [433.163356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.163548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.163726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.163906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.164153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [433.164488] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [433.164806] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [433.165130] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [433.165473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [433.165764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [433.166960] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.167339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.177757] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.177978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.210753] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.211071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823

<7> [433.211419] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614

<7> [433.211633] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614

<7> [433.211565] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.211836] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [433.211943] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.212042] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.212287] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.212304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.212531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.212738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.212966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [433.213200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.213435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.213667] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.213928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [433.214514] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.214779] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823

<7> [433.215010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614

<7> [433.215242] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614

<7> [433.215427] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [433.215672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.215887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.216124] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.216337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.216509] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [433.216670] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.216834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.216996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.217227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [433.217522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [433.217817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [433.218084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [433.218454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [433.218734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [433.219760] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.220053] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.220776] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [433.221031] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [433.227622] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.260779] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.261167] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [433.261280] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.261432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [433.261668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [433.261698] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.261890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.262064] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.262155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [433.262392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [433.262693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [433.262942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [433.263301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [433.263628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [433.263951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [433.264304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [433.264625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [433.265552] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.265906] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.310777] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.311130] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.311268] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.311430] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [433.311648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [433.311645] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.311853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [433.311959] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.312038] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [433.312292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.312470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.312649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.312821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.313013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.313257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [433.313430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [433.313596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [433.313788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [433.314054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [433.314355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [433.314654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [433.314934] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [433.315247] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [433.316623] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.316986] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.327107] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [433.344764] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.345133] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.377407] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.377697] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.377977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [433.378299] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [433.378522] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [433.378451] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.378740] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [433.378850] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.378937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.379173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [433.379202] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.379370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [433.379573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [433.379785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.380004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.380240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.380467] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.380749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [433.381112] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [433.381431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [433.381732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [433.382033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [433.382351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [433.383488] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.383802] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.394386] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.394591] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.427565] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.427874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826

<7> [433.428076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605

<7> [433.428343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620

<7> [433.428536] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [433.428481] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.428728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.428850] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.428913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [433.429122] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [433.429171] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.429305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [433.429529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [433.429728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.429928] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.430168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.430381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [433.430658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [433.430935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [433.431233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [433.431502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [433.431780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [433.432833] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.433137] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.433763] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [433.434045] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [433.444371] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.477389] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.477714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [433.477936] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289

<7> [433.478201] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164

<7> [433.478218] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.478420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.478622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [433.478648] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.478849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [433.479001] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.479062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [433.479377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [433.479682] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [433.479997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [433.480350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [433.480673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [433.480985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [433.481910] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.482287] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.527523] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.527960] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.528482] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913

<7> [433.528563] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.528815] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452

<7> [433.529106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794

<7> [433.529042] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.529357] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892

<7> [433.529532] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.529604] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.529843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [433.530100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [433.530394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [433.530652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.530879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [433.531129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [433.531358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [433.531636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [433.532029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [433.532457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [433.532881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [433.533293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [433.533662] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [433.535299] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.535675] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.543715] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [433.561686] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.562059] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.594229] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.594538] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.594848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691

<7> [433.595205] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676

<7> [433.595443] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350

<7> [433.595364] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.595696] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334

<7> [433.595801] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.595922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.596243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [433.596226] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.596469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [433.596699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [433.596922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.597183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [433.597439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [433.597683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [433.597975] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [433.598361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [433.598700] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [433.599029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [433.599428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [433.599814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [433.601136] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.601480] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.611096] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.611299] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.644261] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.644622] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 691) -> ( 0 - 823), size 691 -> 823

<7> [433.644879] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 691 - 1367) -> ( 823 - 2437), size 676 -> 1614

<7> [433.645186] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2717) -> (2437 - 4051), size 1350 -> 1614

<7> [433.645336] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.645433] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0

<7> [433.645677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.645767] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.645905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.646180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.646196] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.646478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.646726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [433.646943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.647202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.647488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.647801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [433.648193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [433.648539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [433.648875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [433.649227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [433.649617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [433.650858] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.651285] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.652197] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [433.652492] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [433.660923] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.694030] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.694428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [433.694673] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [433.694896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [433.695168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.695394] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [433.695320] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.695631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [433.695721] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.695894] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [433.696115] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.696214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [433.696544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [433.696858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [433.697227] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [433.697541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [433.697854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [433.698678] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.699012] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.744079] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.744446] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.744834] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [433.745170] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [433.745405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [433.745331] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.745635] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [433.745772] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.745886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.746193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.746213] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.746439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.746659] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.746875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.747103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [433.747313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [433.747530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [433.747789] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [433.748169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [433.748529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [433.748876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [433.749222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [433.749576] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [433.750762] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.751138] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.760323] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [433.778083] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.778412] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.810614] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.810895] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.811207] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [433.811321] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.811473] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [433.811680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [433.811708] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.811864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [433.812065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.812009] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.812249] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [433.812443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [433.812679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [433.812880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.813094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.813258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.813416] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.813610] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [433.813898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [433.814233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [433.814502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [433.814765] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [433.815018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [433.816118] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.816419] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.827556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.827767] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.860608] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.860884] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 823), size 686 -> 823

<7> [433.861162] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 823 - 2437), size 686 -> 1614

<7> [433.861350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2437 - 4051), size 1340 -> 1614

<7> [433.861328] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.861553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [433.861664] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.861728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.861900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.861955] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.862129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.862320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.862582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [433.862760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.862930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.863135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [433.863347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [433.863636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [433.863928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [433.864236] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [433.864509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [433.864823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [433.865908] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.866253] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.866869] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [433.867162] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [433.877624] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.910656] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.911010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [433.911366] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [433.911513] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.911602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [433.911843] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.911923] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.912086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [433.912313] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [433.912307] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.912583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [433.912877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [433.913256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [433.913589] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [433.913947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [433.914305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [433.914628] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [433.915556] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.915922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.960621] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.960907] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [433.961277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [433.961329] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [433.961503] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [433.961712] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [433.961698] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [433.961907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [433.962028] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [433.962135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.962328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [433.962571] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [433.962761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [433.962951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [433.963186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [433.963405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [433.963616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [433.963968] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [433.964375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [433.964701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [433.965005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [433.965365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [433.965693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [433.967050] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [433.967383] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [433.976999] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [433.994572] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [433.994868] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [434.027270] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.027531] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [434.027787] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [434.028105] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [434.028245] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.028332] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [434.028552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [434.028650] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.028775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.029012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [434.029000] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.029262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [434.029460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [434.029656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.029849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.030086] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.030303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.030551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [434.030838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [434.031121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [434.031366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [434.031608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [434.031875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [434.033061] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.033348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.044352] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.044560] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [434.077647] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.077963] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 826), size 686 -> 826

<7> [434.078259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 826 - 2431), size 686 -> 1605

<7> [434.078401] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.078472] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (2431 - 4051), size 1340 -> 1620

<7> [434.078693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> ( 0 - 0), size 1339 -> 0

<7> [434.078775] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.078882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.079094] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.079107] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.079289] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [434.079502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [434.079678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [434.079842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.080004] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.080232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.080453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [434.080750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [434.081042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [434.081338] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [434.081598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [434.081907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [434.083003] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.083388] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.084181] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [434.084452] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [434.094277] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.127284] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.127629] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [434.127932] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289

<7> [434.128233] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164

<7> [434.128374] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.128465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.128686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.128778] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.128932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [434.129187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [434.129162] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.129442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [434.130070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.130347] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 826) -> ( 0 - 598), size 826 -> 598

<7> [434.130597] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 826 - 2431) -> ( 598 - 2887), size 1605 -> 2289

<7> [434.130828] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2431 - 4051) -> (2887 - 4051), size 1620 -> 1164

<7> [434.131072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.131288] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.131486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [434.131728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [434.131952] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [434.132321] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [434.132648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [434.132942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [434.133279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [434.133552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [434.134456] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.134794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.177415] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.177784] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [434.178151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913

<7> [434.178251] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.178382] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452

<7> [434.178606] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794

<7> [434.178664] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.178813] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892

<7> [434.179033] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.179032] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.179259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.179477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [434.179677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [434.179872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.180093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.180303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [434.180519] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [434.180794] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [434.181343] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.181591] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [434.181854] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 598) -> ( 0 - 913), size 598 -> 913

<7> [434.182095] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 598 - 2887) -> ( 913 - 1365), size 2289 -> 452

<7> [434.182311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> (1365 - 3159), size 1164 -> 1794

<7> [434.182509] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3159 - 4051), size 0 -> 892

<7> [434.182703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.182908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.183143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [434.183349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [434.183575] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.183787] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.184034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [434.184228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [434.184418] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [434.184721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [434.185048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [434.185332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [434.185621] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [434.185893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [434.187127] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.187426] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.193614] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [434.211192] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.211473] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [434.243939] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.244291] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [434.244595] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 913) -> ( 0 - 691), size 913 -> 691

<7> [434.244894] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 913 - 1365) -> ( 691 - 1367), size 452 -> 676

<7> [434.245305] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 3159) -> (1367 - 2717), size 1794 -> 1350

<7> [434.245352] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.245547] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3159 - 4051) -> (2717 - 4051), size 892 -> 1334

<7> [434.245794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.245785] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.246048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.246205] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.246283] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [434.246535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [434.246769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.246988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.247282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [434.247514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [434.247842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [434.248376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [434.248731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [434.249121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [434.249428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [434.249735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [434.251072] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.251410] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.260862] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [434.261069] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [434.294048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 691) -> ( 0 - 2018), size 691 -> 2018

<7> [434.294180] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.294316] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 691 - 1367) -> (2018 - 4051), size 676 -> 2033

<7> [434.294500] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2717) -> ( 0 - 0), size 1350 -> 0

<7> [434.294512] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.294676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2717 - 4051) -> ( 0 - 0), size 1334 -> 0

<7> [434.294792] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.294853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.295068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.295275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [434.295513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [434.295707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.295896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.296143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.296364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.296599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [434.296813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.296990] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.297222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.297395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [434.297564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.297758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.297947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.298221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [434.298490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [434.298750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [434.299021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [434.299295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [434.299563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [434.300439] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.300754] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.301549] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [434.301821] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A]

<7> [434.327345] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [434.327697] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [434.327959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.328297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [434.328444] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.328542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [434.328797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [434.328886] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.329086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [434.329314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.329433] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [434.329748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [434.330072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [434.330431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [434.330727] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [434.331510] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.331805] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.360617] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.361056] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [434.361188] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.361323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [434.361555] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [434.361599] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.361770] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.361952] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.361993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.362322] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.362559] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.362781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.362991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [434.363274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [434.363501] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [434.363774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [434.364165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [434.364543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [434.364877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [434.365351] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [434.365672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [434.366798] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.367194] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.377565] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.410523] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.410875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [434.411278] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [434.411410] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.411554] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [434.411780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.411821] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.412017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [434.412233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [434.412204] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.412493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [434.412736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.412963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.413264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.413475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.413726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [434.414090] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [434.414420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [434.414732] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [434.415091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [434.415408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [434.416411] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.416754] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.427687] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.460616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2018), size 1606 -> 2018

<7> [434.460962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2018 - 4051), size 826 -> 2033

<7> [434.461345] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0

<7> [434.461475] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.461629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.461872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.461921] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.462179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.462348] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.462449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.462713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [434.462941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.463247] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.463522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.463792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [434.464193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [434.464548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [434.464880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [434.465240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [434.465634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [434.466592] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.466959] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.493974] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [434.494405] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [434.494487] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.494648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.494880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [434.494889] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.495151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [434.495273] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.495382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [434.495680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [434.496068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [434.496389] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [434.496697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [434.497002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [434.497354] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [434.498340] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.498682] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.527231] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.527548] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [434.527764] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [434.527949] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [434.528191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.528362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.528342] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.528536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.528681] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.528739] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.528934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.529028] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.529157] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [434.529336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [434.529525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [434.529729] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [434.530120] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.530360] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [434.530552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [434.530732] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [434.530931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.531173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.531353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.531536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.531714] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.531871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [434.532065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [434.532222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [434.532388] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [434.532674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [434.532959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [434.533252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [434.533537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [434.533784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [434.534899] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.535217] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.544084] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.577245] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.577550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [434.577760] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [434.577960] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [434.578344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.578388] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.578584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [434.578780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [434.578749] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.578967] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [434.579075] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.579305] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.579502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.579706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.579919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.580186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [434.580616] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.580863] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [434.581134] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [434.581334] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [434.581528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.581702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [434.581884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [434.582140] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [434.582366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.582553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.582724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.582885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.583102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [434.583366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [434.583625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [434.583880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [434.584164] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [434.584438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [434.585460] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.585772] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.594021] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.627488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2026), size 1606 -> 2026

<7> [434.627782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2026 - 4051), size 826 -> 2025

<7> [434.628093] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0

<7> [434.628200] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.628350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.628602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.628634] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.628838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [434.629031] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.629131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [434.629350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [434.629572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.629797] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.630054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.630297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [434.630843] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2026), size 1606 -> 2026

<7> [434.631129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2026 - 4051), size 826 -> 2025

<7> [434.631409] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0

<7> [434.631626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.631834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.632082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [434.632290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [434.632487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [434.632704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.632908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.633167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.633364] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [434.633675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [434.634009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [434.634369] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [434.634684] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [434.635012] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [434.636041] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.636352] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.660503] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [434.660774] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [434.661060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.661139] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.661250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.661438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [434.661471] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.661651] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [434.661748] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.661884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [434.662199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [434.662479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [434.662757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [434.663044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [434.663293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [434.664127] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.664402] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.693861] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.694265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2310), size 1354 -> 2310

<7> [434.694372] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.694526] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1354 - 4051) -> (2310 - 2894), size 2697 -> 584

<7> [434.694755] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2894 - 4051), size 0 -> 1157

<7> [434.694808] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.694998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.695221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.695227] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.695458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [434.695720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [434.695940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.696198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.696401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [434.696599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [434.696827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [434.697211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [434.697558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [434.697954] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [434.698312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [434.698630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [434.699880] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.700288] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.710732] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.743824] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.744194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618

<7> [434.744235] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.744480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817

<7> [434.744611] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.744694] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616

<7> [434.744899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.744929] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.745159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.745361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [434.745624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [434.745822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.746037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [434.746223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [434.746398] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [434.746635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [434.746937] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [434.747240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [434.747522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [434.747801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [434.748114] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [434.749245] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.749563] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.760729] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.794023] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2018), size 1618 -> 2018

<7> [434.794017] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.794428] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1618 - 2435) -> (2018 - 4051), size 817 -> 2033

<7> [434.794597] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.794778] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0

<7> [434.795169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.795145] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.795490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.795824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.796207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.796526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [434.796821] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.797197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.797491] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.797836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [434.798361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [434.798881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [434.799408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [434.799889] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [434.800386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [434.801509] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.801945] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.827314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [434.827700] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [434.828054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.828174] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.828301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [434.828566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [434.828618] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.828791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [434.829015] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.829086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [434.829431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [434.829763] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [434.830131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [434.830465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [434.830829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [434.831765] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.832161] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.860517] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.860912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [434.861320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [434.861366] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.861573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [434.861834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.861793] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.862128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.862197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.862363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.862641] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.862872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.863141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [434.863353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [434.863589] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [434.863842] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [434.864281] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [434.864652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [434.865018] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [434.865378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [434.865723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [434.866812] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.867699] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.877576] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.910453] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.910791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [434.911137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [434.911179] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.911352] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [434.911557] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.911655] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.911758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [434.911987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [434.912059] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.912221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [434.912463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.912700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.912889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.913119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.913339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [434.913638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [434.913925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [434.914260] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [434.914544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [434.914824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [434.915727] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.916052] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.927475] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [434.960484] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2018), size 1606 -> 2018

<7> [434.960730] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2018 - 4051), size 826 -> 2033

<7> [434.960929] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0

<7> [434.961185] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.961202] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.961364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.961543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.961570] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.961755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.961974] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [434.961915] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.962152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.962333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.962515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.962721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [434.963152] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2018), size 1606 -> 2018

<7> [434.963357] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2018 - 4051), size 826 -> 2033

<7> [434.963526] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0

<7> [434.963747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.963916] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [434.964197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [434.964384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [434.964579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [434.964741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.964901] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.965119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [434.965292] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [434.965561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [434.965829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [434.966118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [434.966394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [434.966650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [434.967399] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.967675] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [434.993882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [434.994284] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [434.994272] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [434.994530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.994677] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [434.994756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [434.995027] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [434.995054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [434.995282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [434.995565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [434.996044] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2018) -> ( 0 - 1351), size 2018 -> 1351

<7> [434.996292] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2018 - 4051) -> (1351 - 4051), size 2033 -> 2700

<7> [434.996474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [434.996654] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [434.996881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [434.997147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [434.997339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [434.997608] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [434.997862] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [434.998168] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [434.998413] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [434.998651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [434.999423] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [434.999673] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.027269] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.027630] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [435.027874] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [435.028180] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [435.028315] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.028399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.028635] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.028718] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.028866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.029094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.029176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.029395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.029625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [435.029817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [435.030045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [435.030280] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [435.030748] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.031076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1351) -> ( 0 - 2287), size 1351 -> 2287

<7> [435.031337] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1351 - 4051) -> (2287 - 2886), size 2700 -> 599

<7> [435.031566] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2886 - 4051), size 0 -> 1165

<7> [435.031776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.031972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.032156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.032333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.032548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.032752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [435.032992] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [435.033166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [435.033386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [435.033689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [435.034009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [435.034286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [435.034561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [435.034873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [435.035969] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.036276] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.043865] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.077098] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.077406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [435.077646] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [435.077848] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [435.078114] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.078155] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.078325] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.078564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.078535] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.078794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.078856] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.079031] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.079215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.079400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.079580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.079795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [435.080343] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.080623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2287) -> ( 0 - 1606), size 2287 -> 1606

<7> [435.080864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2287 - 2886) -> (1606 - 2432), size 599 -> 826

<7> [435.081112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2886 - 4051) -> (2432 - 4051), size 1165 -> 1619

<7> [435.081328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.081521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.081696] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.081889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.082130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.082365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.082585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.082785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.082967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [435.083215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [435.083452] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [435.083690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.084096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.084408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [435.085439] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.085752] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.093979] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.127318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1606) -> ( 0 - 2026), size 1606 -> 2026

<7> [435.127594] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1606 - 2432) -> (2026 - 4051), size 826 -> 2025

<7> [435.127814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2432 - 4051) -> ( 0 - 0), size 1619 -> 0

<7> [435.128098] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.128324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.128248] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.128547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [435.128650] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.128808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [435.129062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [435.129015] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.129259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.129459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.129665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.129911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [435.130294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [435.130614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [435.130955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [435.131327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [435.131679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [435.132446] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.132782] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.160475] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1354), size 2026 -> 1354

<7> [435.160792] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1354 - 4051), size 2025 -> 2697

<7> [435.161100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.161221] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.161334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.161579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [435.161622] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.161824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [435.162007] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.162160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [435.162489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [435.162800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [435.163142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [435.163514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [435.163878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [435.164876] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.165263] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.193754] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.194101] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1354) -> ( 0 - 2310), size 1354 -> 2310

<7> [435.194189] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.194323] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1354 - 4051) -> (2310 - 2894), size 2697 -> 584

<7> [435.194511] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2894 - 4051), size 0 -> 1157

<7> [435.194564] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.194692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.194870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.194891] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.195178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [435.195371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [435.195560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.195763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.195957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [435.196128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [435.196332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [435.196626] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [435.196940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [435.197228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [435.197504] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [435.197826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [435.198992] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.199296] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.210596] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.243726] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.244137] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 1618), size 2310 -> 1618

<7> [435.244216] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.244411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2894) -> (1618 - 2435), size 584 -> 817

<7> [435.244640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2894 - 4051) -> (2435 - 4051), size 1157 -> 1616

<7> [435.244617] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.244865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.245016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.245130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.245332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [435.245591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [435.245809] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.246064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.246266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [435.246466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [435.246703] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [435.247003] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [435.247279] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [435.247563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.247856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.248150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [435.249168] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.249487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.260643] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.293819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1618) -> ( 0 - 2687), size 1618 -> 2687

<7> [435.294183] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1618 - 2435) -> (2687 - 4051), size 817 -> 1364

<7> [435.294294] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.294425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2435 - 4051) -> ( 0 - 0), size 1616 -> 0

<7> [435.294655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.294693] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.294881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.295065] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.295148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [435.295370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [435.295612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.295838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.296065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.296241] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.296428] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [435.296599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.296768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.296966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.297209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [435.297577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [435.297882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [435.298208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [435.298486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [435.298741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [435.299527] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.299827] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.343889] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [435.344254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [435.344490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.344704] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.344959] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.345153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.345104] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.345392] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [435.345489] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.345689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [435.345815] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.345987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [435.346252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.346539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.346807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [435.347616] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.347954] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.377474] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:474]

<7> [435.378059] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.378505] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.378849] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.407364] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.407823] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907

<7> [435.408104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392

<7> [435.408321] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752

<7> [435.408523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.408719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.408927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.409121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.409309] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.409493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [435.409682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [435.409866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [435.410122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [435.410458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [435.410771] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [435.411070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [435.411350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [435.411629] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [435.412869] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.413178] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.428426] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.460609] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.461107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [435.461061] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.461419] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [435.461707] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [435.461623] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.462019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.462122] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.462306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.462592] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.462867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.463169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.463438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.463707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.463985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.464305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [435.465004] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.465327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [435.465576] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [435.465815] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [435.466064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.466303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.466542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.466778] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.467032] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.467272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.467509] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.467745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.468048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [435.468454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [435.468846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [435.469255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [435.469640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [435.470021] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [435.471420] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.471776] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.477530] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.510731] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687

<7> [435.511132] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.511191] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364

<7> [435.511491] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [435.511571] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.511775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.512071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.512024] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.512353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.512624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.512886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [435.513145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.513384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.513621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.513931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [435.514576] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687

<7> [435.514834] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364

<7> [435.515098] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [435.515337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.515573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.515812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.516065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.516303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [435.516539] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.516777] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.517034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.517293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [435.517701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [435.518132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [435.518489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [435.518841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [435.519209] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [435.520441] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.520809] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.543933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [435.543948] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.544241] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [435.544338] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.544501] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.544715] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.544775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.545085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.545361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.545663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [435.546291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [435.546533] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [435.546755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.546992] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.547214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.547415] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.547630] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [435.548123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [435.548325] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [435.548508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.548692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.548877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.549064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.549252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [435.549529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [435.549788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [435.550056] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.550301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.550538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [435.551399] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.551639] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.577193] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.577577] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907

<7> [435.577842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392

<7> [435.578181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752

<7> [435.578179] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.578459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.578636] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.578725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.578998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.579054] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.579239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.579478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.579712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [435.579966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [435.580205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [435.580490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [435.581252] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.581567] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907

<7> [435.581797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392

<7> [435.582052] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752

<7> [435.582270] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.582481] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.582683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.582883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.583101] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.583285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [435.583468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [435.583648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [435.583846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [435.584157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [435.584437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [435.584704] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [435.584969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [435.585223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [435.586370] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.586600] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.593819] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.627139] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.627532] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [435.627814] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [435.628122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [435.628135] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.628378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.628515] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.628621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.628861] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.628873] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.629127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.629368] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.629602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.629839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.630093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.630381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [435.630793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [435.631211] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [435.631601] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [435.632008] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [435.632394] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [435.634062] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.634424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.644061] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.677472] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697

<7> [435.677790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354

<7> [435.678099] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [435.678109] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.678362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.678482] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.678612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.678858] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [435.678835] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.679102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [435.679327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [435.679544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.679759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.679994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.680254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [435.680631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [435.681016] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [435.681377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [435.681735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [435.682105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [435.683277] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.683638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.710449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [435.710729] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [435.711029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.711032] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.711282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.711403] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.711527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [435.711766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [435.711755] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.712055] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [435.712429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [435.712788] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [435.713157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.713509] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.713858] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [435.715039] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.715404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.743763] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.744094] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.744139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936

<7> [435.744379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376

<7> [435.744434] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.744603] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739

<7> [435.744752] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.744822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.745099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.745330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [435.745551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [435.745769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.746002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.746222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [435.746437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [435.746692] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [435.747078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [435.747442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [435.747799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [435.748177] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [435.748499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [435.749974] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.750325] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.760757] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.793776] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.794151] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.794195] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2936) -> ( 0 - 2306), size 2936 -> 2306

<7> [435.794471] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2936 - 3312) -> (2306 - 2893), size 376 -> 587

<7> [435.794524] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.794724] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3312 - 4051) -> (2893 - 4051), size 739 -> 1158

<7> [435.794898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.794986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.795231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.795476] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [435.795718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [435.795983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.796223] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [435.796463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [435.796699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [435.796980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [435.797357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [435.797718] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [435.798098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [435.798453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [435.798804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [435.800425] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.800793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.810839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.843797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2306) -> ( 0 - 2687), size 2306 -> 2687

<7> [435.844142] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2306 - 2893) -> (2687 - 4051), size 587 -> 1364

<7> [435.844149] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.844408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2893 - 4051) -> ( 0 - 0), size 1158 -> 0

<7> [435.844518] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.844660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.844913] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.844888] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.845144] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.845363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.845582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [435.845798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.846040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.846259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [435.846522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [435.846921] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [435.847282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [435.847634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [435.848002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [435.848352] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [435.849397] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.849758] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.877117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [435.877403] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [435.877638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.877905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.877915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.878137] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.878251] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.878361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.878571] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.878622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [435.879015] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [435.879377] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [435.879728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.880097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [435.880444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [435.881480] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.881842] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.910481] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.910937] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907

<7> [435.910917] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.911218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392

<7> [435.911299] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.911474] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752

<7> [435.911650] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.911720] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.911985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.912229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.912469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.912706] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.912958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [435.913176] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [435.913390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [435.913652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [435.914468] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.914764] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907

<7> [435.915096] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392

<7> [435.915319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752

<7> [435.915535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.915749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.915983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.916197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.916413] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.916626] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [435.916839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [435.917067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [435.917301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [435.917665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [435.918028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [435.918356] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [435.918677] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [435.919017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [435.920249] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.920548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.927187] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.960581] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.961004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [435.961067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [435.961369] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [435.961417] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [435.961648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [435.961803] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [435.961951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.962224] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.962494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.962758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.963050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.963314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.963577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.963837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.964163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [435.964837] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [435.965182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [435.965432] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [435.965671] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [435.965922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.966158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [435.966395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [435.966633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [435.966884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [435.967118] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [435.967354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [435.967588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [435.967839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [435.968262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [435.968651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [435.969022] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [435.969362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [435.969686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [435.970872] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [435.971161] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [435.977118] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [436.010479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687

<7> [436.010923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364

<7> [436.010922] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.011228] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [436.011328] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.011512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.011713] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.011793] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.012065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.012312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.012553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [436.012791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.013063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.013301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.013593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [436.014380] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2687), size 2289 -> 2687

<7> [436.014642] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2687 - 4051), size 598 -> 1364

<7> [436.014908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [436.015146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.015382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.015620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.015887] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.016126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [436.016358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.016593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.016830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.017254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [436.017623] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [436.018091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [436.018448] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [436.018804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [436.019175] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [436.020326] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.020652] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.043808] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2687) -> ( 0 - 2021), size 2687 -> 2021

<7> [436.044148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2687 - 4051) -> (2021 - 4051), size 1364 -> 2030

<7> [436.044146] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.044405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.044517] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.044648] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [436.044950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [436.044914] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.045194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [436.045479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [436.045899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [436.046262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [436.046614] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [436.046986] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [436.047329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [436.048401] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.048716] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.077141] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [436.077557] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2021) -> ( 0 - 2907), size 2021 -> 2907

<7> [436.077903] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.077966] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2021 - 4051) -> (2907 - 3299), size 2030 -> 392

<7> [436.078215] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3299 - 4051), size 0 -> 752

<7> [436.078272] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.078457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.078617] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.078698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.078966] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.079209] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.079447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.079683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [436.079940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [436.080179] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [436.080461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [436.080882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [436.081282] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [436.081673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [436.082074] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [436.082457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [436.084064] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.084400] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.094062] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [436.127143] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [436.127627] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2907) -> ( 0 - 2289), size 2907 -> 2289

<7> [436.128002] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2907 - 3299) -> (2289 - 2887), size 392 -> 598

<7> [436.128015] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.128302] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (2887 - 4051), size 752 -> 1164

<7> [436.128420] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.128580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.128805] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.128881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [436.129156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [436.129429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [436.129691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.129976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.130242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.130505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.130824] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [436.131305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [436.131753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [436.132393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [436.132784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [436.133294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [436.135129] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.135537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.144019] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [436.177496] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2289) -> ( 0 - 2697), size 2289 -> 2697

<7> [436.177912] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2289 - 2887) -> (2697 - 4051), size 598 -> 1354

<7> [436.177923] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.178224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2887 - 4051) -> ( 0 - 0), size 1164 -> 0

<7> [436.178329] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.178506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.178712] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.178781] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.179104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [436.179379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [436.179647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [436.179931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.180200] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.180465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.180784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [436.181278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [436.181721] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [436.182131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [436.182517] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [436.182920] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [436.184165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.184557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.210411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2697) -> ( 0 - 2026), size 2697 -> 2026

<7> [436.210723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2697 - 4051) -> (2026 - 4051), size 1354 -> 2025

<7> [436.211054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.211027] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.211306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.211393] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.211551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [436.211789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [436.211739] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.212100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [436.212514] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [436.212924] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [436.213315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [436.213698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [436.214100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [436.215311] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.215672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.243739] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [436.244182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2936), size 2026 -> 2936

<7> [436.244136] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.244460] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2936 - 3312), size 2025 -> 376

<7> [436.244718] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3312 - 4051), size 0 -> 739

<7> [436.244642] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.244995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.245076] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.245244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.245489] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [436.245729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [436.245983] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.246219] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.246457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [436.246691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [436.246977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [436.247349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [436.247709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [436.248088] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [436.248442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [436.248793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [436.250432] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.250794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.260768] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [436.293710] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [436.294182] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2936) -> ( 0 - 2306), size 2936 -> 2306

<7> [436.294127] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.294466] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2936 - 3312) -> (2306 - 2893), size 376 -> 587

<7> [436.294635] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.294722] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3312 - 4051) -> (2893 - 4051), size 739 -> 1158

<7> [436.294998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.295072] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.295244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.295489] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [436.295731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [436.295998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.296246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.296485] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [436.296723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [436.297009] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [436.297385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [436.297745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [436.298113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [436.298469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [436.298840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [436.300479] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.300871] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.310860] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [436.343769] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.344252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2306) -> ( 0 - 583), size 2306 -> 583

<7> [436.344203] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.344539] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2306 - 2893) -> ( 583 - 2898), size 587 -> 2315

<7> [436.344704] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.344800] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2893 - 4051) -> (2898 - 4051), size 1158 -> 1153

<7> [436.345080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.345146] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.345337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.345586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [436.345847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [436.346088] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.346323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.346561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.346800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.347041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.347255] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.347470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 4, 8, 8, 8, 8, 8, 0, 0, 19, 4, 19

<7> [436.347685] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [436.347972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [436.348531] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.348816] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2306) -> ( 0 - 583), size 2306 -> 583

<7> [436.349065] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2306 - 2893) -> ( 583 - 2898), size 587 -> 2315

<7> [436.349285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2893 - 4051) -> (2898 - 4051), size 1158 -> 1153

<7> [436.349501] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.349718] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.349954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [436.350170] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [436.350387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.350602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.350837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.351054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.351269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.351484] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.351699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 4, 8, 8, 8, 8, 8, 0, 0, 19, 4, 19

<7> [436.351929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [436.352145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [436.352482] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [436.352811] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [436.353156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [436.353479] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [436.353801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [436.355130] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.355424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.359990] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A]

<7> [436.360392] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [436.360529] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [436.377640] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.410541] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.411046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [436.410994] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.411361] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939

<7> [436.411553] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.411648] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737

<7> [436.411958] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.412042] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.412233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [436.412506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [436.412774] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [436.413091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [436.413704] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.414035] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [436.414289] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939

<7> [436.414528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737

<7> [436.414764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.415029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [436.415271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [436.415510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [436.415766] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [436.416189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [436.416584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [436.416990] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [436.417347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [436.417699] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [436.418811] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.419190] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.460365] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.460873] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.461081] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.461414] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.461381] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.461769] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673

<7> [436.461791] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.462070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692

<7> [436.462326] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333

<7> [436.462572] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353

<7> [436.462841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.463085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.463328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.463572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.463836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.464076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [436.464318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [436.464560] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [436.464875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [436.465291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [436.465687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [436.466089] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [436.466443] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [436.466796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [436.468335] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.468703] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.476666] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [436.494415] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.494737] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.527042] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.527397] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.527746] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452

<7> [436.528054] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913

<7> [436.528073] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.528314] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893

<7> [436.528562] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793

<7> [436.528573] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.528842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.529016] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.529091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [436.529337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [436.529577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [436.529836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.530071] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.530307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.530545] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.531425] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [436.532191] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.532461] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.532736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452

<7> [436.532987] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913

<7> [436.533207] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893

<7> [436.533423] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793

<7> [436.533639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.533877] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [436.534097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [436.534311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [436.534525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.534741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.534978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.535195] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.535430] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [436.535795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [436.536140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [436.536466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [436.536792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [436.537131] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [436.538567] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.539048] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.544030] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.544214] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.577099] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.577528] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 452) -> ( 0 - 583), size 452 -> 583

<7> [436.577877] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 452 - 1365) -> ( 583 - 2898), size 913 -> 2315

<7> [436.577897] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.578166] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2258) -> (2898 - 4051), size 893 -> 1153

<7> [436.578441] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0

<7> [436.578459] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.578708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.578977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.578942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.579221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.579457] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.579692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [436.579950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.580189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.580424] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.580709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [436.581139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [436.581537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [436.581945] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [436.582333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [436.582719] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [436.584470] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.584834] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.585476] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [436.585734] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [436.594054] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.627008] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.627406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [436.627685] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939

<7> [436.627984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737

<7> [436.628004] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.628239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.628486] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [436.628512] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.628732] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [436.628998] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [436.628956] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.629288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [436.629707] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [436.630128] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [436.630522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [436.630931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [436.631320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [436.632571] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.632968] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.677062] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.677438] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.677838] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673

<7> [436.677863] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.678109] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692

<7> [436.678359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333

<7> [436.678368] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.678601] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353

<7> [436.678785] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.678864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.679104] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.679345] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.679583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.679842] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.680081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [436.680320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [436.680555] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [436.680861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [436.681276] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [436.681678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [436.682071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [436.682427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [436.682785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [436.684592] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.684973] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.693205] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [436.711060] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.711384] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.743715] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.744180] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.744194] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.744583] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452

<7> [436.744758] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.744939] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913

<7> [436.745201] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893

<7> [436.745210] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.745450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793

<7> [436.745693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.745955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [436.746201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [436.746443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [436.746681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.746935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [436.747177] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [436.747416] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [436.747709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [436.748358] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [436.748757] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [436.749312] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [436.749696] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [436.750067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [436.751875] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.752245] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.760888] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.761148] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.793833] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.793985] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.794391] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 452) -> ( 0 - 585), size 452 -> 585

<7> [436.794364] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.794681] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 452 - 1365) -> ( 585 - 2894), size 913 -> 2309

<7> [436.794782] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.794969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2258) -> (2894 - 4051), size 893 -> 1157

<7> [436.795229] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0

<7> [436.795478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.795725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.796000] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [436.796242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [436.796483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [436.796719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.796976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.797214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [436.797499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [436.797925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [436.798288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [436.798640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [436.799006] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [436.799360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [436.800974] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.801343] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.802119] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [436.802427] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [436.810933] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.843735] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.844177] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [436.844127] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.844390] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 585 - 2894) -> ( 376 - 3312), size 2309 -> 2936

<7> [436.844497] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.844585] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2894 - 4051) -> (3312 - 4051), size 1157 -> 739

<7> [436.844767] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.844837] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.844960] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.845139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [436.845320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [436.845575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [436.846196] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.846507] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [436.846738] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 585 - 2894) -> ( 376 - 3312), size 2309 -> 2936

<7> [436.846990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2894 - 4051) -> (3312 - 4051), size 1157 -> 739

<7> [436.847218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.847439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.847652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [436.847886] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [436.848127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [436.848483] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [436.848868] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [436.849158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [436.849427] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [436.849673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [436.851078] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.851442] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.893457] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.893677] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.893799] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.893802] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.893916] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 376) -> ( 0 - 679), size 376 -> 679

<7> [436.893956] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.894000] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 376 - 3312) -> ( 679 - 1358), size 2936 -> 679

<7> [436.894080] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3312 - 4051) -> (1358 - 2705), size 739 -> 1347

<7> [436.894086] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.894166] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2705 - 4051), size 0 -> 1346

<7> [436.894246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.894324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.894399] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [436.894474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [436.894548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.894624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.894694] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [436.894764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [436.894944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [436.895071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [436.895186] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [436.895306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [436.895429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [436.895554] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [436.896453] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.896587] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.909837] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [436.927941] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.928180] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.960805] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.960832] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [436.961303] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [436.961409] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [436.961758] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 679) -> ( 0 - 456), size 679 -> 456

<7> [436.961944] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [436.962104] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 679 - 1358) -> ( 456 - 1360), size 679 -> 904

<7> [436.962411] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1358 - 2705) -> (1360 - 2259), size 1347 -> 899

<7> [436.962704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2705 - 4051) -> (2259 - 4051), size 1346 -> 1792

<7> [436.963023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.963312] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.963597] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [436.963890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [436.964163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [436.964434] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [436.964709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [436.965023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [436.965386] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [436.965894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [436.966355] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [436.966830] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [436.967278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [436.967714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [436.969999] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [436.970402] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [436.977968] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [436.978290] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.010444] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.010826] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.010978] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 456) -> ( 0 - 583), size 456 -> 583

<7> [437.011296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 456 - 1360) -> ( 583 - 2898), size 904 -> 2315

<7> [437.011319] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.011587] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1360 - 2259) -> (2898 - 4051), size 899 -> 1153

<7> [437.011756] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.011904] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2259 - 4051) -> ( 0 - 0), size 1792 -> 0

<7> [437.012186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.012464] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.012741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.013023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.013280] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [437.013534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.013795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.014039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.014365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [437.015299] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.015650] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 456) -> ( 0 - 583), size 456 -> 583

<7> [437.015928] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 456 - 1360) -> ( 583 - 2898), size 904 -> 2315

<7> [437.016179] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1360 - 2259) -> (2898 - 4051), size 899 -> 1153

<7> [437.016425] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2259 - 4051) -> ( 0 - 0), size 1792 -> 0

<7> [437.016672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.016949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.017212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.017471] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.017724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [437.017988] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.018229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.018471] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.018741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [437.019167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [437.019571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [437.019981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [437.020380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [437.020796] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [437.022535] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.022922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.024088] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [437.024358] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [437.027575] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.060401] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.060829] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.060920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [437.061222] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939

<7> [437.061323] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.061501] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737

<7> [437.061799] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.061809] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.062070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [437.062340] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [437.062609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [437.062980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [437.063453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [437.063928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [437.064362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [437.064812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [437.065245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [437.066689] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.067148] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.110486] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.110841] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.110820] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.111163] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673

<7> [437.111361] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692

<7> [437.111342] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.111546] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333

<7> [437.111722] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353

<7> [437.111952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.111850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.112139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.112321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.112540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.112749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.112973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [437.113136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [437.113296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [437.113499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [437.113778] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [437.114078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [437.114349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [437.114616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [437.114915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [437.116194] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.116502] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.126499] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [437.144001] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.144266] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.176782] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.177044] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.177318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452

<7> [437.177593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913

<7> [437.177865] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893

<7> [437.177897] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.178062] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793

<7> [437.178252] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.178271] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.178442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [437.178592] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.178631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [437.178903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [437.179109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.179327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.179515] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.179740] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.180023] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [437.180318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [437.180585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [437.180869] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [437.181160] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [437.181400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [437.182334] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.182610] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.193816] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.194070] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.226727] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.227012] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 452) -> ( 0 - 583), size 452 -> 583

<7> [437.227202] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 452 - 1365) -> ( 583 - 2898), size 913 -> 2315

<7> [437.227378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2258) -> (2898 - 4051), size 893 -> 1153

<7> [437.227549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0

<7> [437.227783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.227977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.227940] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.228159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.228337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.228284] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.228511] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [437.228584] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.228724] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.228962] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.229160] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.229403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [437.229678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [437.229964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [437.230212] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [437.230454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [437.230695] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [437.231646] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.231933] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.232541] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [437.232776] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [437.243826] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.276716] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.277018] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 583) -> ( 0 - 375), size 583 -> 375

<7> [437.277216] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 583 - 2898) -> ( 375 - 3314), size 2315 -> 2939

<7> [437.277400] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (3314 - 4051), size 1153 -> 737

<7> [437.277579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.277783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [437.277915] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.277971] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [437.278189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [437.278263] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.278396] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [437.278560] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.278676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [437.278972] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [437.279225] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [437.279523] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [437.279782] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [437.280594] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.280902] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.326754] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.327008] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.327291] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 375) -> ( 0 - 673), size 375 -> 673

<7> [437.327488] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 375 - 3314) -> ( 673 - 1365), size 2939 -> 692

<7> [437.327676] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (1365 - 2698), size 737 -> 1333

<7> [437.327909] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2698 - 4051), size 0 -> 1353

<7> [437.328087] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.328043] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.328257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.328427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.328390] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.328628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.328685] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.328844] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.329017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [437.329191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [437.329359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [437.329553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [437.329834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [437.330072] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [437.330310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [437.330543] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [437.330804] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [437.331806] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.332074] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.343100] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [437.360511] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.360764] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.393471] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.393698] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.393984] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 673) -> ( 0 - 452), size 673 -> 452

<7> [437.394105] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.394192] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 673 - 1365) -> ( 452 - 1365), size 692 -> 913

<7> [437.394359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2698) -> (1365 - 2258), size 1333 -> 893

<7> [437.394431] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.394521] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2698 - 4051) -> (2258 - 4051), size 1353 -> 1793

<7> [437.394680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.394709] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.394882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [437.395052] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [437.395220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [437.395382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.395547] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.395717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.395986] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.396201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [437.396469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [437.396749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [437.396985] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [437.397262] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [437.397494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [437.398467] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.398755] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.410626] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.410934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.443659] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.443973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 452) -> ( 0 - 585), size 452 -> 585

<7> [437.444059] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.444181] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 452 - 1365) -> ( 585 - 2894), size 913 -> 2309

<7> [437.444376] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2258) -> (2894 - 4051), size 893 -> 1157

<7> [437.444403] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.444607] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2258 - 4051) -> ( 0 - 0), size 1793 -> 0

<7> [437.444697] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.444839] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.445012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [437.445187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [437.445386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [437.445552] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [437.445713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.445935] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.446126] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.446349] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [437.446627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [437.446927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [437.447220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [437.447480] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [437.447756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [437.448627] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.448919] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.449505] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [437.449725] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [437.460502] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.493396] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.493675] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 585) -> ( 0 - 376), size 585 -> 376

<7> [437.493936] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 585 - 2894) -> ( 376 - 3312), size 2309 -> 2936

<7> [437.493999] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.494128] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2894 - 4051) -> (3312 - 4051), size 1157 -> 739

<7> [437.494310] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.494325] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.494487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [437.494607] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.494663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [437.494922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [437.495132] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [437.495407] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [437.495674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [437.495976] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [437.496229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [437.496476] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [437.497183] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.497448] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.543527] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.543930] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.544327] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 376) -> ( 0 - 679), size 376 -> 679

<7> [437.544612] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 376 - 3312) -> ( 679 - 1358), size 2936 -> 679

<7> [437.544925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3312 - 4051) -> (1358 - 2705), size 739 -> 1347

<7> [437.545070] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.545175] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2705 - 4051), size 0 -> 1346

<7> [437.545418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.545544] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.545660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [437.546017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [437.546011] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.546269] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [437.546499] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.546736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [437.546980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [437.547220] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [437.547487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [437.547880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [437.548300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [437.548658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [437.549036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [437.549390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [437.550866] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.551241] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.559772] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [437.577480] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.577786] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.610040] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.610306] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.610581] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 679) -> ( 0 - 456), size 679 -> 456

<7> [437.610926] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 679 - 1358) -> ( 456 - 1360), size 679 -> 904

<7> [437.611059] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.611148] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1358 - 2705) -> (1360 - 2259), size 1347 -> 899

<7> [437.611362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2705 - 4051) -> (2259 - 4051), size 1346 -> 1792

<7> [437.611453] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.611576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.611829] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.611878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [437.612106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [437.612311] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [437.612513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.612738] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [437.612945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [437.613164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [437.613393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [437.613708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [437.614045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [437.614329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [437.614607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [437.614929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [437.616136] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.616431] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.627139] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.627402] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.659978] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.660229] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 456) -> ( 0 - 814), size 456 -> 814

<7> [437.660443] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 456 - 1360) -> ( 814 - 2440), size 904 -> 1626

<7> [437.660623] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1360 - 2259) -> (2440 - 4051), size 899 -> 1611

<7> [437.660847] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2259 - 4051) -> ( 0 - 0), size 1792 -> 0

<7> [437.661037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.660997] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.661221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [437.661341] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.661407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [437.661623] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [437.661634] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.661853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.662026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.662214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.662403] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.662578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.662780] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [437.662950] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 8, 8, 8, 8, 8, 0, 0, 19, 4, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [437.663116] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [437.663277] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [437.663436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.663593] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.663769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.663943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [437.664189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [437.664432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [437.664677] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [437.664999] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [437.665251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [437.666079] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.666335] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.667018] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [437.667253] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [437.676852] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.709985] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.710282] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [437.710506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [437.710751] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [437.710949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.710894] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.711139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [437.711242] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.711327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [437.711526] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [437.711540] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.711746] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [437.712027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [437.712300] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [437.712570] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [437.712864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [437.713113] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [437.713768] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.714053] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.759994] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.760269] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.760529] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896

<7> [437.760773] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471

<7> [437.760950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774

<7> [437.760889] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.761120] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910

<7> [437.761213] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.761284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.761478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.761487] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.761660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.761911] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.762079] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.762242] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [437.762405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [437.762600] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [437.762844] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [437.763100] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [437.763353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [437.763599] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [437.763918] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [437.764159] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [437.765036] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.765296] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.776388] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [437.793743] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.793993] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.826634] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.826903] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.827146] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676

<7> [437.827366] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691

<7> [437.827552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335

<7> [437.827769] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349

<7> [437.827940] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.827907] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.828139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [437.828233] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.828308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [437.828470] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [437.828512] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.828640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.828846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.829025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.829197] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.829395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [437.829669] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [437.829967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [437.830215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [437.830474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [437.830769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [437.831741] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.831996] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.843668] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.843916] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.876774] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.877039] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 676) -> ( 0 - 814), size 676 -> 814

<7> [437.877238] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 676 - 1367) -> ( 814 - 2440), size 691 -> 1626

<7> [437.877426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2702) -> (2440 - 4051), size 1335 -> 1611

<7> [437.877611] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0

<7> [437.877846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.878018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.877992] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.878225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.878337] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.878418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.878580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [437.878628] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.878779] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.878943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.879111] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [437.879302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [437.879572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [437.879850] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [437.880096] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [437.880368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [437.880596] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [437.881540] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.881841] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.882440] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [437.882653] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [437.893826] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.926618] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.926950] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [437.927211] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [437.927408] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [437.927598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.927832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [437.928008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [437.927979] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.928210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [437.928304] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.928409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [437.928579] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.928857] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.929061] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [437.929259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [437.929421] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [437.929583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.929776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [437.929954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [437.930152] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [437.930323] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [437.930575] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [437.930841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [437.931153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [437.931410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [437.931665] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [437.932413] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.932722] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.976625] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.976945] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.977218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896

<7> [437.977418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471

<7> [437.977605] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774

<7> [437.977833] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910

<7> [437.978013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.977970] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [437.978226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.978316] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [437.978417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.978608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.978614] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [437.978819] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.978976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [437.979163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [437.979349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [437.979540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [437.979995] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [437.980191] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [437.980388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896

<7> [437.980549] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471

<7> [437.980727] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774

<7> [437.980893] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910

<7> [437.981054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.981212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [437.981404] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [437.981584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [437.981824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [437.981985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [437.982151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [437.982303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [437.982465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [437.982744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [437.983057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [437.983319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [437.983578] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [437.983905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [437.984922] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [437.985189] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [437.992980] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [438.010510] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.010787] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.043249] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.043472] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.043731] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676

<7> [438.043859] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.043928] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691

<7> [438.044116] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335

<7> [438.044204] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.044298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349

<7> [438.044478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.044497] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.044656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [438.044885] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [438.045068] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [438.045240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.045410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.045583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.045800] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.045992] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [438.046250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [438.046500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [438.046764] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [438.047007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [438.047293] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [438.048231] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.048490] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.060399] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.060659] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.093424] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.093734] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 676) -> ( 0 - 817), size 676 -> 817

<7> [438.093858] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.093975] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 676 - 1367) -> ( 817 - 2434), size 691 -> 1617

<7> [438.094167] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2702) -> (2434 - 4051), size 1335 -> 1617

<7> [438.094203] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.094356] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0

<7> [438.094496] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.094577] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.094792] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.094973] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [438.095149] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [438.095323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [438.095494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.095665] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.096002] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.096206] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [438.096474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [438.096780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [438.097026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [438.097268] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [438.097524] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [438.098385] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.098638] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.099306] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [438.099524] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [438.110425] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.143250] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.143511] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [438.143742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 817 - 2434) -> ( 588 - 2893), size 1617 -> 2305

<7> [438.143929] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2434 - 4051) -> (2893 - 4051), size 1617 -> 1158

<7> [438.143867] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.144108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.144194] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.144284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.144475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [438.144475] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.144693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [438.144891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [438.145200] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [438.145459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [438.145728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [438.145988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [438.146235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [438.146936] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.147224] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.193613] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.193839] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.194003] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.194211] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.194304] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 588) -> ( 0 - 905), size 588 -> 905

<7> [438.194517] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 588 - 2893) -> ( 905 - 1360), size 2305 -> 455

<7> [438.194536] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.194754] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2893 - 4051) -> (1360 - 3152), size 1158 -> 1792

<7> [438.194933] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3152 - 4051), size 0 -> 899

<7> [438.195108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.195281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.195452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [438.195656] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [438.195878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.196064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.196221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [438.196371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [438.196558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [438.196839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [438.197105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [438.197364] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [438.197627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [438.197997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [438.199367] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.199699] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.209651] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [438.227130] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.227359] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.259893] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.260110] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.260334] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 905) -> ( 0 - 681), size 905 -> 681

<7> [438.260553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 905 - 1360) -> ( 681 - 1362), size 455 -> 681

<7> [438.260791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1360 - 3152) -> (1362 - 2707), size 1792 -> 1345

<7> [438.260969] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3152 - 4051) -> (2707 - 4051), size 899 -> 1344

<7> [438.260939] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.261139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.261306] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.261267] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.261474] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [438.261543] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.261652] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [438.261869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.262036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.262226] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [438.262389] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [438.262577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [438.262854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [438.263104] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [438.263347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [438.263584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [438.263911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [438.264924] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.265198] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.277078] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.277341] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.309905] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.310172] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 681) -> ( 0 - 814), size 681 -> 814

<7> [438.310412] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 681 - 1362) -> ( 814 - 2440), size 681 -> 1626

<7> [438.310602] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1362 - 2707) -> (2440 - 4051), size 1345 -> 1611

<7> [438.310853] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2707 - 4051) -> ( 0 - 0), size 1344 -> 0

<7> [438.311029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.311002] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.311201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.311330] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.311371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.311570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.311604] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.311803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [438.311984] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.312163] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.312373] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.312591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [438.312942] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [438.313235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [438.313550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [438.313961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [438.314201] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [438.315139] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.315398] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.316087] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [438.316301] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [438.327087] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.359934] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.360215] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [438.360444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [438.360641] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [438.360903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.361082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [438.361052] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.361257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [438.361380] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.361462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [438.361699] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.361709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [438.362066] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.362271] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [438.362433] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [438.362593] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [438.362789] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.362947] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [438.363119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [438.363316] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [438.363499] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [438.363784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [438.364044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [438.364294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [438.364544] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [438.364876] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [438.365499] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.365801] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.410001] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.410351] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.410583] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.410862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896

<7> [438.410963] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.411059] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471

<7> [438.411246] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774

<7> [438.411310] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.411429] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910

<7> [438.411606] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.411678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.411869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.412049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.412260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.412463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.412674] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [438.412845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [438.413013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [438.413208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [438.413472] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [438.413749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [438.414000] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [438.414244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [438.414534] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [438.415473] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.415746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.426284] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [438.443786] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.444036] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.476562] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.476935] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.477199] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676

<7> [438.477406] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691

<7> [438.477604] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335

<7> [438.477866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349

<7> [438.478050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.478009] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.478229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [438.478352] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.478410] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [438.478624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [438.478695] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.478868] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.479048] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.479246] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.479462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.479726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [438.480174] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.480366] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.480569] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676

<7> [438.480819] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691

<7> [438.480989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335

<7> [438.481143] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349

<7> [438.481303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.481477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [438.481629] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [438.481836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [438.481989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.482139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.482290] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.482442] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.482603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [438.482898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [438.483146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [438.483385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [438.483618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [438.483958] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [438.484956] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.485216] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.493419] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.493603] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.526545] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.526866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 676) -> ( 0 - 814), size 676 -> 814

<7> [438.527132] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 676 - 1367) -> ( 814 - 2440), size 691 -> 1626

<7> [438.527353] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2702) -> (2440 - 4051), size 1335 -> 1611

<7> [438.527566] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0

<7> [438.527836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.528034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.527960] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.528248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.528331] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.528469] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.528692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [438.528688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.528866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.529038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.529205] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.529406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [438.529708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [438.529980] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [438.530244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [438.530506] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [438.530795] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [438.531923] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.532220] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.532887] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [438.533134] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [438.543530] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.576519] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.576846] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 814) -> ( 0 - 586), size 814 -> 586

<7> [438.577055] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 814 - 2440) -> ( 586 - 2896), size 1626 -> 2310

<7> [438.577253] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2440 - 4051) -> (2896 - 4051), size 1611 -> 1155

<7> [438.577445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.577628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [438.577876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [438.578061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [438.578034] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.578291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [438.578360] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.578558] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [438.578688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.578843] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [438.579111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [438.579376] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [438.579659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [438.580390] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.580688] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.626539] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.626831] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.627080] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 586) -> ( 0 - 896), size 586 -> 896

<7> [438.627310] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 586 - 2896) -> ( 896 - 1367), size 2310 -> 471

<7> [438.627502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (1367 - 3141), size 1155 -> 1774

<7> [438.627711] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3141 - 4051), size 0 -> 910

<7> [438.627875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.627855] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.628039] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.628201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.628179] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.628387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.628460] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.628561] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.628788] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [438.628963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [438.629123] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [438.629310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [438.629579] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [438.629866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [438.630105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [438.630343] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [438.630627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [438.631735] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.631996] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.642892] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [438.660345] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.660575] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.693155] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.693385] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.693667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 896) -> ( 0 - 676), size 896 -> 676

<7> [438.693794] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.693860] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 896 - 1367) -> ( 676 - 1367), size 471 -> 691

<7> [438.694035] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 3141) -> (1367 - 2702), size 1774 -> 1335

<7> [438.694137] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.694208] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3141 - 4051) -> (2702 - 4051), size 910 -> 1349

<7> [438.694374] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.694420] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.694540] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [438.694737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [438.694931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [438.695125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.695301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.695477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.695717] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.695950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [438.696224] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [438.696490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [438.696784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [438.697033] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [438.697320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [438.698288] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.698544] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.710278] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.710533] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.743316] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.743578] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 676) -> ( 0 - 817), size 676 -> 817

<7> [438.743835] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 676 - 1367) -> ( 817 - 2434), size 691 -> 1617

<7> [438.744016] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2702) -> (2434 - 4051), size 1335 -> 1617

<7> [438.743991] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.744192] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2702 - 4051) -> ( 0 - 0), size 1349 -> 0

<7> [438.744362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.744319] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.744529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.744598] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.744733] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [438.744901] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [438.745099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [438.745281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.745468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.745640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.745821] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [438.746079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [438.746333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [438.746584] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [438.746887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [438.747149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [438.748135] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.748413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.749119] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [438.749368] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [438.760317] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.793178] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.793455] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 817) -> ( 0 - 588), size 817 -> 588

<7> [438.793706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 817 - 2434) -> ( 588 - 2893), size 1617 -> 2305

<7> [438.793906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2434 - 4051) -> (2893 - 4051), size 1617 -> 1158

<7> [438.793832] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.794097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.794207] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.794285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.794466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [438.794512] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.794693] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [438.794891] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [438.795152] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [438.795408] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [438.795676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [438.795971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [438.796220] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [438.796960] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.797239] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.843181] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.843532] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.843854] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.843969] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.844124] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 588) -> ( 0 - 905), size 588 -> 905

<7> [438.844319] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 588 - 2893) -> ( 905 - 1360), size 2305 -> 455

<7> [438.844315] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.844506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2893 - 4051) -> (1360 - 3152), size 1158 -> 1792

<7> [438.844723] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3152 - 4051), size 0 -> 899

<7> [438.844729] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.844897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.845090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.845272] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [438.845461] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [438.845632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.845795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.845960] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [438.846120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [438.846308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [438.846577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [438.846882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [438.847154] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [438.847417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [438.847709] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [438.848889] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.849169] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.859560] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [438.877170] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.877414] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.909938] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.910175] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.910420] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 905) -> ( 0 - 681), size 905 -> 681

<7> [438.910704] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 905 - 1360) -> ( 681 - 1362), size 455 -> 681

<7> [438.910899] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1360 - 3152) -> (1362 - 2707), size 1792 -> 1345

<7> [438.910837] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.911083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3152 - 4051) -> (2707 - 4051), size 899 -> 1344

<7> [438.911185] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.911266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.911446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.911485] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.911699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [438.911880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [438.912053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.912216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [438.912384] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [438.912551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [438.912780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 4172520 num active planes 4

<7> [438.913039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 4382 qgv_peak_bw: 38400

<7> [438.913288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 4382 qgv_peak_bw: 38400

<7> [438.913526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [438.913790] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 4382 qgv_peak_bw: 38400

<7> [438.914091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 4382

<7> [438.915115] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.915390] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.927102] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [438.927366] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [438.959841] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 681) -> ( 0 - 2026), size 681 -> 2026

<7> [438.960049] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 681 - 1362) -> (2026 - 4051), size 681 -> 2025

<7> [438.960237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1362 - 2707) -> ( 0 - 0), size 1345 -> 0

<7> [438.960417] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2707 - 4051) -> ( 0 - 0), size 1344 -> 0

<7> [438.960590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.960832] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.961018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.960966] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [438.961243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.961314] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [438.961450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.961647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.961653] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [438.961812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.961972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.962131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [438.962321] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.962505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.962707] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.962874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [438.963036] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.963199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.963358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.963548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [438.964046] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 681) -> ( 0 - 2026), size 681 -> 2026

<7> [438.964209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 681 - 1362) -> (2026 - 4051), size 681 -> 2025

<7> [438.964365] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1362 - 2707) -> ( 0 - 0), size 1345 -> 0

<7> [438.964519] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2707 - 4051) -> ( 0 - 0), size 1344 -> 0

<7> [438.964731] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.964893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.965047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.965198] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.965380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [438.965551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [438.965790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [438.966013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [438.966180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [438.966329] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.966475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.966640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.966785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [438.966924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.967059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.967193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [438.967337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [438.967580] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [438.967861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [438.968117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [438.968370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [438.968633] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [438.969296] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [438.969558] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [438.970271] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [438.970508] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A]

<7> [439.009782] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [439.010036] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [439.010249] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.010449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [439.010713] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [439.010845] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.010937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [439.011191] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.011196] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [439.011483] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.011486] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [439.011781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [439.012036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.012336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.012581] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [439.013331] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.013594] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.043087] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.043339] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [439.043573] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [439.043831] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [439.044013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.043959] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.044194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.044307] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.044375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.044550] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.044642] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.044768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.044930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [439.045091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [439.045248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [439.045429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [439.045728] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [439.045997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [439.046258] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.046516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.046819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [439.047587] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.047922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.060080] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.093052] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.093275] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [439.093465] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [439.093668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [439.093830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.093812] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.093991] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [439.094166] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [439.094139] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.094364] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [439.094420] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.094534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.094723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.094879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.095029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.095202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [439.095469] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [439.095772] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [439.096014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.096250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.096532] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [439.097310] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.097570] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.110034] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.143084] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [439.143273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [439.143442] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [439.143645] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.143813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.143789] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.143999] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.144137] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.144202] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.144375] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [439.144430] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.144536] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.144742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.144893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.145065] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [439.145315] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [439.145556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [439.145840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [439.146097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [439.146384] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [439.147106] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.147378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.176467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [439.176693] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [439.176873] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.176828] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.177044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [439.177248] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [439.177201] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.177419] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [439.177491] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.177620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [439.177874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [439.178126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [439.178409] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.178664] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.178911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [439.179713] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.179987] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.209753] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.209973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [439.210139] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [439.210296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [439.210453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.210637] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.210808] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.210791] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.210976] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.211141] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.211155] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.211334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [439.211443] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.211521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [439.211735] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [439.211919] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [439.212183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [439.212463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [439.212749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.213002] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.213270] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [439.214157] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.214403] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.226802] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.259738] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.260017] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [439.260254] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [439.260450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [439.260682] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.260878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [439.260820] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.261067] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [439.261168] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.261281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [439.261463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.261467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.261672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.261838] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.261997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.262198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [439.262474] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [439.262755] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [439.263013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.263266] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.263512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [439.264412] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.264714] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.276858] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.310038] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [439.310277] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [439.310480] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [439.310726] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.310908] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.310854] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.311103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [439.311179] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.311285] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [439.311453] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [439.311453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.311647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.311813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.312006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.312195] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [439.312559] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [439.312771] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [439.312930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [439.313085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.313238] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.313412] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [439.313613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [439.313775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [439.313937] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.314095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.314253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.314420] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [439.314715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [439.314977] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [439.315237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [439.315494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [439.315779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [439.316616] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.316882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.343130] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [439.343412] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [439.343711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.343836] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.343922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.344147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [439.344208] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.344378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [439.344527] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.344661] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [439.345071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [439.345264] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [439.345452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.345678] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.345863] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [439.346081] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [439.346301] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [439.346714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [439.346907] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [439.347095] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.347320] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.347524] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [439.347765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [439.347955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [439.348246] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [439.348529] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [439.348847] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.349158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.349419] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [439.350270] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.350547] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.376501] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.376940] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [439.376984] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.377226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [439.377467] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [439.377409] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.377756] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.377822] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.377985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.378210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [439.378478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [439.378741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.378989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.379199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [439.379406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [439.379676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [439.380267] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.380529] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [439.380799] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [439.381013] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [439.381253] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.381459] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.381698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [439.381895] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [439.382100] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.382300] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.382500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [439.382747] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [439.382981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [439.383289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [439.383639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [439.383940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.384233] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.384502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [439.385473] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.385758] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.393024] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.426392] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.426748] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [439.426849] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.426977] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [439.427193] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [439.427218] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.427400] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.427537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.427631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.427824] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [439.428047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [439.428234] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.428408] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.428598] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [439.428769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [439.428964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [439.429234] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [439.429500] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [439.429791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.430079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.430361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [439.431351] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.431653] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.443397] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.476388] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2026), size 1627 -> 2026

<7> [439.476699] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2026 - 4051), size 814 -> 2025

<7> [439.476813] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.476906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [439.477103] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.477158] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.477295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.477453] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.477483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.477758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.477951] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [439.478132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.478336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.478513] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.478767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [439.479039] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [439.479314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [439.479607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [439.479874] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [439.480137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [439.480868] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.481151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.526350] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [439.526552] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [439.526811] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.526996] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [439.526950] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.527194] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [439.527299] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.527406] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [439.527628] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.527674] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [439.527926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [439.528171] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [439.528432] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.528697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.528982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [439.529624] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.529881] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.559759] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.560061] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [439.560289] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [439.560506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [439.560817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.561020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.560967] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.561217] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.561414] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.561370] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.561649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.561757] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.561846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [439.562040] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [439.562232] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [439.562449] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [439.562791] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [439.563142] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [439.563438] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.563761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.564084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [439.564906] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.565234] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.576700] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.609702] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.609962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [439.610158] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [439.610338] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [439.610512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.610743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [439.610927] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [439.610886] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.611146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [439.611230] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.611350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.611525] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.611530] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.611755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.611930] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.612127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [439.612393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [439.612685] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [439.612959] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.613217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.613478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [439.614275] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.614537] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.626681] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.659701] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2026), size 1615 -> 2026

<7> [439.659932] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2026 - 4051), size 823 -> 2025

<7> [439.660136] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [439.660330] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.660517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.660768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.660942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.660920] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.661145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [439.661246] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.661328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.661506] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.661526] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.661728] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.661929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [439.662199] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [439.662465] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [439.662808] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [439.663057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [439.663306] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [439.664131] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.664413] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.693036] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 1361), size 2026 -> 1361

<7> [439.693281] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (1361 - 4051), size 2025 -> 2690

<7> [439.693488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.693746] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [439.693938] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [439.693895] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.694158] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [439.694246] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.694366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [439.694584] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.694655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [439.694926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [439.695178] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.695424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.695744] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [439.696533] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.696831] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.726346] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.726605] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [439.726704] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.726787] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [439.726962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [439.727054] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.727133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.727301] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.727351] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.727466] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.727671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.727836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.727995] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [439.728155] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [439.728343] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [439.728569] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [439.728939] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.729138] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1361) -> ( 0 - 2293), size 1361 -> 2293

<7> [439.729297] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1361 - 4051) -> (2293 - 2890), size 2690 -> 597

<7> [439.729450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2890 - 4051), size 0 -> 1161

<7> [439.729640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.729791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.729942] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.730090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.730243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.730396] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [439.730569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [439.730721] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [439.730881] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [439.731141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [439.731397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [439.731678] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.731982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.732240] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [439.733115] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.733384] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.743094] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.776385] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.776705] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [439.776797] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.776915] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [439.777112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [439.777146] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.777303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.777445] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.777488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [439.777725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [439.777899] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [439.778099] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.778277] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.778455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.778657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.778846] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [439.779194] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.779392] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 1615), size 2293 -> 1615

<7> [439.779566] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (1615 - 2438), size 597 -> 823

<7> [439.779726] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (2438 - 4051), size 1161 -> 1613

<7> [439.779890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.780058] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [439.780227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [439.780393] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [439.780583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.780745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.780903] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.781062] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.781229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [439.781491] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [439.781785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [439.782061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.782344] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.782615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [439.783516] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.783826] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.793080] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.826553] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [439.826687] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.826785] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [439.826990] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [439.827052] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.827186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.827377] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.827346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.827591] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [439.827775] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [439.827982] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [439.828159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.828335] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.828507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.828761] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [439.829198] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1615) -> ( 0 - 2033), size 1615 -> 2033

<7> [439.829362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1615 - 2438) -> (2033 - 4051), size 823 -> 2018

<7> [439.829520] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2438 - 4051) -> ( 0 - 0), size 1613 -> 0

<7> [439.829730] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.829889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.830061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [439.830254] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [439.830426] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [439.830603] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.830757] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.830907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.831064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 2

<7> [439.831313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400

<7> [439.831567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400

<7> [439.831826] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [439.832067] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400

<7> [439.832304] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461

<7> [439.833019] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.833290] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.859697] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2033) -> ( 0 - 1364), size 2033 -> 1364

<7> [439.859949] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2033 - 4051) -> (1364 - 4051), size 2018 -> 2687

<7> [439.860159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.860356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.860582] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [439.860706] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.860769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [439.861013] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [439.861046] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.861290] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [439.861327] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.861560] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [439.861820] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.862080] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.862373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [439.863215] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.863469] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.892957] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.893207] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1364) -> ( 0 - 2316), size 1364 -> 2316

<7> [439.893418] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1364 - 4051) -> (2316 - 2898), size 2687 -> 582

<7> [439.893643] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (2898 - 4051), size 0 -> 1153

<7> [439.893822] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.893786] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.893994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.894178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [439.894132] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.894350] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [439.894423] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.894517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.894735] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.894893] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [439.895070] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [439.895271] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [439.895553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [439.895800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [439.896051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.896291] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [439.896600] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [439.897448] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.897744] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.909909] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.942933] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.943179] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2316) -> ( 0 - 1627), size 2316 -> 1627

<7> [439.943358] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2316 - 2898) -> (1627 - 2441), size 582 -> 814

<7> [439.943568] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2898 - 4051) -> (2441 - 4051), size 1153 -> 1610

<7> [439.943743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.943705] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.943906] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.944069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [439.944031] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.944257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [439.944315] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.944429] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.944611] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [439.944766] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [439.944915] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [439.945097] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [439.945357] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [439.945636] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [439.945882] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.946133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [439.946415] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [439.947292] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.947566] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [439.959901] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [439.993020] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 1627) -> ( 0 - 2691), size 1627 -> 2691

<7> [439.993245] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (1627 - 2441) -> (2691 - 4051), size 814 -> 1360

<7> [439.993449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2441 - 4051) -> ( 0 - 0), size 1610 -> 0

<7> [439.993716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.993754] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [439.993905] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [439.994120] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [439.994122] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [439.994317] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [439.994440] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [439.994493] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [439.994723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [439.994919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [439.995139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [439.995328] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [439.995512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.995765] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.995957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [439.996189] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [439.996568] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [439.996910] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [439.997251] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.997598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [439.997947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [439.998965] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [439.999321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.042996] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [440.043236] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [440.043425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.043655] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.043773] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.043840] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.044054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.044121] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.044259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [440.044421] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.044555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [440.044815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [440.045061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.045353] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.045616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [440.046261] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.046529] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.077896] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:475]

<7> [440.077759] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.078188] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.078564] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.100722] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.101119] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [440.101456] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [440.101796] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [440.102034] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.102266] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.102496] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.102830] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.103060] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.103282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [440.103482] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [440.103725] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [440.104017] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [440.104328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [440.104656] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [440.104997] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.105288] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.105733] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [440.106579] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.106882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.110235] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.143017] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.143424] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [440.143830] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [440.144099] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [440.143992] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.144356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.144481] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.144694] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.144953] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.144966] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.145206] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.145523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.145768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.146076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.146341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.146659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [440.147032] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [440.147424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [440.147838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.148256] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.148639] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [440.149649] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.150120] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.159918] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.192930] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [440.193164] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [440.193366] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [440.193610] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.193802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.193735] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.193987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.194083] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.194184] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.194362] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [440.194383] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.194563] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.194737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.194898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.195085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [440.195453] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [440.195660] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [440.195818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [440.196017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.196186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.196349] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.196527] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.196697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [440.196912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.197097] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.197278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.197467] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [440.197819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [440.198157] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [440.198463] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [440.198859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [440.199218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [440.200118] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.200405] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.226362] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [440.226675] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [440.226798] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.226888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.227082] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.227144] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.227268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.227440] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.227489] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.227769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [440.228195] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [440.228378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [440.228578] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.228748] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.228948] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.229132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.229335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [440.229616] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [440.229878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [440.230136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.230442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.230734] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [440.231609] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.231887] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.259721] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.260041] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [440.260269] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [440.260479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [440.260759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.260945] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.260887] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.261127] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.261237] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.261327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.261514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.261556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.261687] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [440.261856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [440.262023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [440.262217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [440.262617] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.262828] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [440.262992] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [440.263153] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [440.263315] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.263529] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.263712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.263872] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.264045] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.264215] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [440.264385] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [440.264586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [440.264762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [440.265030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [440.265294] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [440.265571] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.265837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.266105] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [440.267036] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.267310] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.276325] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.309576] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.309856] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [440.310056] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [440.310240] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [440.310418] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.310639] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.310785] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.310847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.311063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.311133] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.311262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.311443] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.311425] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.311677] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.311849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.312037] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [440.312476] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.312736] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [440.312913] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [440.313086] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [440.313259] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.313427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.313634] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.313833] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.314026] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.314186] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.314342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.314508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.314673] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [440.314929] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [440.315182] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [440.315457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.315748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.316026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [440.317017] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.317341] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.326397] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.359791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [440.360026] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [440.360230] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [440.360425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.360684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.360865] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [440.360824] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.361075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [440.361150] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.361271] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [440.361446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.361430] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.361657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.361823] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.362014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [440.362264] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [440.362525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [440.362783] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [440.363034] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [440.363327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [440.364049] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.364329] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.392921] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [440.393169] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [440.393382] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.393633] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.393762] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.393831] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [440.394063] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [440.394110] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.394278] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [440.394406] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.394567] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [440.394834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [440.395084] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.395331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.395648] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [440.396380] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.396663] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.426218] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.426463] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [440.426733] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [440.426913] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [440.426856] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.427091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.427203] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.427265] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.427435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [440.427531] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.427703] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [440.427890] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.428043] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.428191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [440.428339] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [440.428527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [440.428780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [440.429046] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [440.429310] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.429594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.429896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [440.430826] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.431101] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.443113] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.476208] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.476451] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [440.476742] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [440.476919] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [440.476893] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.477092] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.477263] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.477243] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.477432] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [440.477570] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.477698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [440.477869] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.478050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.478221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [440.478407] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [440.478650] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [440.478957] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [440.479221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [440.479516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.479807] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.480057] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [440.480921] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.481183] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.493422] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.526218] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 2691), size 2310 -> 2691

<7> [440.526456] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> (2691 - 4051), size 586 -> 1360

<7> [440.526731] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> ( 0 - 0), size 1155 -> 0

<7> [440.526922] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.526878] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.527109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.527205] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.527292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.527522] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.527506] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.527711] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [440.527889] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.528072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.528291] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.528527] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [440.528823] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [440.529081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [440.529334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [440.529609] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [440.529854] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [440.530518] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.530800] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.559561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [440.559761] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [440.559943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.560121] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.560296] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.560542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.560676] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.560756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [440.561014] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [440.561037] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.561265] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [440.561330] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.561531] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.561835] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.562091] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [440.562708] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.562983] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.592839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.593080] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [440.593259] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [440.593431] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [440.593671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.593847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.593810] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.594019] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.594156] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.594218] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.594386] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.594455] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.594590] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [440.594760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [440.594919] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [440.595102] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [440.595350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [440.595625] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [440.595877] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.596107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.596350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [440.597063] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.597327] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.609839] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.642834] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.643067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [440.643270] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [440.643435] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [440.643660] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.643829] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.643783] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.644015] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.644130] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.644201] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.644363] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.644422] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.644556] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.644716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.644878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.645064] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [440.645435] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.645690] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [440.645862] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [440.646028] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [440.646193] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.646353] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.646543] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.646700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.646878] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.647038] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.647190] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.647331] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.647494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [440.647735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [440.647971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [440.648208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.648437] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.648708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [440.649377] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.649654] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.659723] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.692908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [440.693140] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [440.693346] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [440.693599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.693722] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.693794] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.693985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.694070] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.694188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.694401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [440.694364] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.694618] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.694790] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.694952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.695139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [440.695523] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2691), size 2293 -> 2691

<7> [440.695698] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2691 - 4051), size 597 -> 1360

<7> [440.695866] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [440.696030] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.696189] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.696379] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.696672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.696845] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [440.697023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.697182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.697337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.697572] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [440.697836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [440.698099] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [440.698363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [440.698713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [440.699010] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [440.699725] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.699999] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.726224] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [440.726500] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [440.726709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.726631] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.726896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.726996] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.727073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.727275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.727269] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.727510] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [440.727889] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [440.728060] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [440.728221] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.728378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.728588] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.728755] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.728923] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [440.729295] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2691) -> ( 0 - 2026), size 2691 -> 2026

<7> [440.729529] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2691 - 4051) -> (2026 - 4051), size 1360 -> 2025

<7> [440.729692] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.729859] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.730018] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.730174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.730339] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [440.730631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [440.730897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [440.731155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.731423] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.731708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [440.732520] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.732793] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.759598] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.759884] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [440.760127] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [440.760318] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [440.760535] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.760710] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.760674] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.760882] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.761061] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.761017] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.761227] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.761298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.761388] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [440.761579] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [440.761736] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [440.761914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [440.762351] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.762595] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2026) -> ( 0 - 2910), size 2026 -> 2910

<7> [440.762780] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2026 - 4051) -> (2910 - 3301), size 2025 -> 391

<7> [440.762948] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3301 - 4051), size 0 -> 750

<7> [440.763107] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.763260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.763409] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.763601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.763759] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.763917] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [440.764075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [440.764231] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [440.764397] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [440.764701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [440.764966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [440.765222] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.765494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.765779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [440.766693] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.766942] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.776236] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.809586] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.809901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2910) -> ( 0 - 2293), size 2910 -> 2293

<7> [440.810100] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2910 - 3301) -> (2293 - 2890), size 391 -> 597

<7> [440.810285] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (2890 - 4051), size 750 -> 1161

<7> [440.810487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.810661] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [440.810645] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.810836] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [440.810978] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.811054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [440.811257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.811277] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.811480] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [440.811672] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [440.811853] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [440.812040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [440.812289] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [440.812548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [440.812792] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.813045] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.813305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [440.814256] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.814549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.826590] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.859664] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2293) -> ( 0 - 2701), size 2293 -> 2701

<7> [440.859882] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2293 - 2890) -> (2701 - 4051), size 597 -> 1350

<7> [440.860074] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> ( 0 - 0), size 1161 -> 0

<7> [440.860257] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.860435] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.860679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [440.860855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [440.860798] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.861024] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [440.861148] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.861214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.861378] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.861428] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.861576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [440.861770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 2

<7> [440.862050] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [440.862325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [440.862624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [440.862893] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [440.863158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [440.863948] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.864247] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.892835] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2701) -> ( 0 - 2031), size 2701 -> 2031

<7> [440.893068] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2701 - 4051) -> (2031 - 4051), size 1350 -> 2020

<7> [440.893261] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.893441] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.893684] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [440.893870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [440.893814] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.894121] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 2

<7> [440.894186] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.894398] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [440.894513] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.894711] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [440.894964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.895208] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [440.895516] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [440.896334] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.896636] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.926143] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.926383] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2031) -> ( 0 - 2939), size 2031 -> 2939

<7> [440.926622] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2031 - 4051) -> (2939 - 3314), size 2020 -> 375

<7> [440.926791] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb ( 0 - 0) -> (3314 - 4051), size 0 -> 737

<7> [440.926766] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.926952] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.927109] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.927093] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.927281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [440.927365] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.927494] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [440.927658] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.927847] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.928008] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [440.928165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [440.928361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [440.928680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [440.928931] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [440.929173] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.929411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [440.929681] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [440.930543] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.930818] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.943038] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.976126] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [440.976378] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2939) -> ( 0 - 2310), size 2939 -> 2310

<7> [440.976637] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2939 - 3314) -> (2310 - 2896), size 375 -> 586

<7> [440.976818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3314 - 4051) -> (2896 - 4051), size 737 -> 1155

<7> [440.976759] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [440.976993] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.977164] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.977106] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [440.977333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [440.977404] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [440.977534] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [440.977700] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [440.977907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [440.978084] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [440.978251] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [440.978462] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [440.978774] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [440.979029] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [440.979318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.979595] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [440.979839] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [440.981657] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [440.981921] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [440.993237] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:124:plane 4A]

<7> [441.026125] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.026407] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 2310) -> ( 0 - 597), size 2310 -> 597

<7> [441.026683] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb (2310 - 2896) -> ( 597 - 2890), size 586 -> 2293

<7> [441.026810] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.026884] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2896 - 4051) -> (2890 - 4051), size 1155 -> 1161

<7> [441.027080] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.027181] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.027268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.027477] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.027501] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.027681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.027884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.028057] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.028222] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.028383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.028585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.028745] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [441.028920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [441.029119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [441.029317] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [441.029603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [441.029864] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [441.030124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [441.030453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [441.030708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [441.031522] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.031794] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.042529] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A]

<7> [441.043138] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [441.043401] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [441.060130] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.092784] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.093065] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [441.093273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [441.093520] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [441.093716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.093671] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.093904] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [441.094010] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.094078] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [441.094275] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [441.094284] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.094487] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [441.094855] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.095070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [441.095245] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [441.095413] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [441.095631] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.095798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [441.095955] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [441.096107] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [441.096269] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [441.096548] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [441.096801] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [441.097063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [441.097324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [441.097643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [441.098321] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.098641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.142856] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.143246] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.143589] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.143608] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.143880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [441.143958] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.144076] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [441.144262] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [441.144261] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.144465] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [441.144644] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.144827] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.145013] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.145236] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.145445] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.145621] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [441.145803] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [441.145994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [441.146223] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [441.146538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [441.146849] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [441.147169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [441.147511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [441.147872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [441.148854] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.149199] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.159202] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [441.176680] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.176929] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.209574] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.209794] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.210033] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [441.210250] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [441.210479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [441.210665] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [441.210626] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.210848] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.211017] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [441.210978] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.211187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [441.211250] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.211380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [441.211612] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.211773] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.211949] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.212125] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.212329] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [441.212634] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [441.212901] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [441.213145] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [441.213446] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [441.213687] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [441.214461] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.214734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.226474] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.226734] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.259413] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.259717] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [441.259917] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [441.260107] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [441.260290] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [441.260569] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.260753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.260705] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.260931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.261052] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.261145] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.261336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [441.261346] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.261616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.261798] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.261954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.262138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [441.262632] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.262852] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [441.263039] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [441.263194] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [441.263345] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [441.263531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.263681] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.263866] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.264021] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.264174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [441.264323] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.264507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.264658] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.264818] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [441.265079] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [441.265334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [441.265618] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [441.265872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [441.266118] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [441.267123] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.267382] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.268064] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [441.268297] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [441.276270] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.309390] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.309692] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [441.309931] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [441.310123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [441.310298] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.310532] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [441.310652] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.310709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [441.310912] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [441.310986] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.311138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [441.311283] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.311410] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [441.311723] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [441.311987] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [441.312253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [441.312539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [441.313313] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.313953] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.359452] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.359720] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.359989] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [441.360173] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [441.360343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [441.360561] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [441.360729] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.360711] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.360924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.361091] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.361038] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.361250] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.361314] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.361421] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.361576] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [441.361727] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [441.361875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [441.362051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [441.362305] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [441.362583] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [441.362833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [441.363111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [441.363350] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [441.364343] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.364648] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.375823] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [441.393142] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.393391] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.426086] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.426332] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.426640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [441.426755] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.426873] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [441.427071] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [441.427142] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.427265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [441.427508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.427490] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.427702] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [441.427897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [441.428131] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [441.428336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.428564] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.428753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.428929] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.429136] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [441.429417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [441.429753] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [441.430035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [441.430375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [441.430873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [441.431903] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.432195] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.443119] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.443383] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.476220] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.476497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [441.476610] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.476725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [441.476920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [441.476940] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.477106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [441.477233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.477287] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.477500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [441.477683] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [441.477898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [441.478064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [441.478225] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.478387] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.478599] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.478785] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [441.479036] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [441.479283] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [441.479553] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [441.479799] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [441.480098] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [441.480941] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.481218] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.481906] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [441.482144] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [441.493107] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.526044] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.526330] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [441.526660] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.526749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [441.526952] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [441.527007] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.527146] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.527298] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.527337] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [441.527620] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [441.527816] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [441.528071] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [441.528373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [441.528708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [441.529001] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [441.529287] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [441.529660] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [441.530417] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.530701] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.576287] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.576764] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.576868] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.577129] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [441.577301] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.577379] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [441.577688] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [441.577726] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.577901] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [441.578108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.578358] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [441.578622] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [441.578810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [441.578989] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.579165] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [441.579336] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [441.579585] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [441.579815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [441.580140] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [441.580458] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [441.580759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [441.581077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [441.581478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [441.582799] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.583175] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.592449] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [441.610127] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.610433] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.642874] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.643112] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.643354] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [441.643616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [441.643806] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [441.643747] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.643993] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [441.644093] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.644175] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.644354] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [441.644435] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.644586] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [441.644764] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [441.644977] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.645161] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [441.645334] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [441.645609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [441.645814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [441.646085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [441.646347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [441.646638] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [441.646884] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [441.647167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [441.648041] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.648300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.659805] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.659999] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.692812] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.693065] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 597), size 471 -> 597

<7> [441.693297] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 597 - 2890), size 896 -> 2293

<7> [441.693527] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2890 - 4051), size 910 -> 1161

<7> [441.693708] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [441.693675] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.693883] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.694054] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.694023] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.694258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.694318] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.694478] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.694666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [441.694828] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.694987] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.695147] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.695332] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [441.695626] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [441.695890] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [441.696174] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [441.696494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [441.696773] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [441.697428] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.697687] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.698340] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [441.698592] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [441.709790] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.742663] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.742920] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [441.743116] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [441.743306] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [441.743552] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.743737] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [441.743688] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.743926] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [441.744045] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.744130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [441.744337] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [441.744336] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.744642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [441.744905] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [441.745221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [441.745525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [441.745780] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [441.746463] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.746730] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.792796] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.793092] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.793345] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [441.793633] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [441.793818] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [441.793776] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.793997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [441.794172] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.794128] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.794344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.794450] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.794572] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.794743] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.794932] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.795106] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [441.795258] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [441.795444] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [441.795631] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [441.795887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [441.796138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [441.796395] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [441.796663] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [441.796911] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [441.797760] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.798040] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.809082] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [441.826390] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.826622] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.859316] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.859567] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.859790] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [441.859997] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [441.860183] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [441.860364] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [441.860609] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.860791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [441.860747] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.860969] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [441.861093] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.861187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [441.861395] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.861412] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.861607] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.861782] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.861946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.862133] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [441.862403] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [441.862651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [441.862899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [441.863156] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [441.863421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [441.864248] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.864549] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.876349] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.876653] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [441.909322] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.909631] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 597), size 468 -> 597

<7> [441.909875] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 597 - 2890), size 904 -> 2293

<7> [441.910053] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2890 - 4051), size 904 -> 1161

<7> [441.910225] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [441.910430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.910601] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [441.910565] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.910768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [441.910900] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.910963] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [441.911134] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [441.911203] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.911302] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.911509] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.911676] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [441.911880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [441.912139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [441.912400] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [441.912644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [441.912898] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [441.913172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [441.914224] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.914548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [441.915165] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 983040 bytes of contiguous stolen space for FBC, limit: 2

<7> [441.915424] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [441.926307] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.959310] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [441.959630] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 391), size 597 -> 391

<7> [441.959890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 391 - 3301), size 2293 -> 2910

<7> [441.960083] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (3301 - 4051), size 1161 -> 750

<7> [441.960262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [441.960490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [441.960671] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [441.960549] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [441.960888] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [441.961135] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [441.961205] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [441.961424] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [441.961691] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [441.961771] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [441.961940] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [441.962184] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [441.962439] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [441.963194] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [441.963525] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [442.009547] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.009925] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.010265] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 391) -> ( 0 - 686), size 391 -> 686

<7> [442.010655] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 391 - 3301) -> ( 686 - 1372), size 2910 -> 686

<7> [442.010890] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3301 - 4051) -> (1372 - 2712), size 750 -> 1340

<7> [442.010766] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [442.011117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2712 - 4051), size 0 -> 1339

<7> [442.011338] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.011405] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [442.011619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [442.011860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [442.011885] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [442.012072] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [442.012281] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.012544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [442.012752] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [442.012965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [442.013213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [442.013585] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [442.013922] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [442.014255] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [442.014615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [442.014984] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [442.016285] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [442.016669] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [442.025678] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [442.042761] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.043004] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.075950] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.076163] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.076426] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 686) -> ( 0 - 468), size 686 -> 468

<7> [442.076534] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [442.076652] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 686 - 1372) -> ( 468 - 1372), size 686 -> 904

<7> [442.076844] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2712) -> (1372 - 2276), size 1340 -> 904

<7> [442.076873] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [442.077032] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2712 - 4051) -> (2276 - 4051), size 1339 -> 1775

<7> [442.077214] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.077173] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [442.077427] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [442.077608] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [442.077802] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [442.077981] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.078143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [442.078307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [442.078521] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [442.078730] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [442.079028] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [442.079297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [442.079591] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [442.079907] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [442.080161] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [442.081101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [442.081401] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [442.093146] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.093449] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.126216] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.126502] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 468) -> ( 0 - 599), size 468 -> 599

<7> [442.126592] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [442.126718] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 468 - 1372) -> ( 599 - 2885), size 904 -> 2286

<7> [442.126896] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 2276) -> (2885 - 4051), size 904 -> 1166

<7> [442.126917] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [442.127067] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2276 - 4051) -> ( 0 - 0), size 1775 -> 0

<7> [442.127197] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [442.127237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.127479] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [442.127662] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [442.127862] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [442.128050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [442.128210] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [442.128390] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [442.128549] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [442.128731] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1738550 num active planes 3

<7> [442.128989] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1826 qgv_peak_bw: 38400

<7> [442.129239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1826 qgv_peak_bw: 38400

<7> [442.129505] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [442.129745] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1826 qgv_peak_bw: 38400

<7> [442.129991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1826

<7> [442.130882] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [442.131161] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [442.131862] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 245760 bytes of contiguous stolen space for FBC, limit: 2

<7> [442.132099] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [442.143102] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.175929] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.176209] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [442.176483] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [442.176684] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [442.176624] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [442.176879] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.176972] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [442.177059] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [442.177233] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [442.177254] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [442.177475] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [442.177698] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [442.178117] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.178322] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 599) -> ( 0 - 392), size 599 -> 392

<7> [442.178580] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 599 - 2885) -> ( 392 - 3299), size 2286 -> 2907

<7> [442.178749] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2885 - 4051) -> (3299 - 4051), size 1166 -> 752

<7> [442.178909] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.179069] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [442.179229] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23

<7> [442.179460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24

<7> [442.179654] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2433970 num active planes 3

<7> [442.179914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2556 qgv_peak_bw: 38400

<7> [442.180183] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2556 qgv_peak_bw: 38400

<7> [442.180496] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [442.180754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2556 qgv_peak_bw: 38400

<7> [442.181007] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2556

<7> [442.181757] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [442.182028] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [442.226047] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.226336] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.226668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [442.226661] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [442.226870] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [442.227057] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [442.227018] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [442.227237] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [442.227312] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [442.227448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.227624] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [442.227791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [442.227980] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [442.228156] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.228359] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [442.228514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [442.228666] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [442.228859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [442.229360] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.229556] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.229755] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 392) -> ( 0 - 693), size 392 -> 693

<7> [442.229923] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 392 - 3299) -> ( 693 - 1365), size 2907 -> 672

<7> [442.230089] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (3299 - 4051) -> (1365 - 2718), size 752 -> 1353

<7> [442.230273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (2718 - 4051), size 0 -> 1333

<7> [442.230514] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.230688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [442.230864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 5, 14, 14, 14, 14, 14, 0, 0, 23, 5, 23 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [442.231047] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 9, 21, 21, 21, 21, 21, 0, 0, 24, 9, 24 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [442.231228] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.231450] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [442.231628] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19

<7> [442.231806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20

<7> [442.231996] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2086260 num active planes 4

<7> [442.232296] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2191 qgv_peak_bw: 38400

<7> [442.232635] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2191 qgv_peak_bw: 38400

<7> [442.232946] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [442.233214] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2191 qgv_peak_bw: 38400

<7> [442.233522] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2191

<7> [442.234694] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [442.235024] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [442.242363] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [442.259805] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.260075] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.292592] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.292820] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.293050] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 693) -> ( 0 - 471), size 693 -> 471

<7> [442.293256] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 693 - 1365) -> ( 471 - 1367), size 672 -> 896

<7> [442.293485] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1365 - 2718) -> (1367 - 2277), size 1353 -> 910

<7> [442.293662] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2718 - 4051) -> (2277 - 4051), size 1333 -> 1774

<7> [442.293606] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [442.293834] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.293936] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [442.294012] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [442.294192] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [442.294238] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [442.294420] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [442.294596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.294776] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0

<7> [442.294946] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21

<7> [442.295139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22

<7> [442.295374] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [442.295627] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [442.295883] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [442.296144] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [442.296411] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [442.296715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [442.297606] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [442.297882] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [442.309672] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.309933] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.342621] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.342902] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 471) -> ( 0 - 823), size 471 -> 823

<7> [442.343117] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 471 - 1367) -> ( 823 - 2437), size 896 -> 1614

<7> [442.343320] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1367 - 2277) -> (2437 - 4051), size 910 -> 1614

<7> [442.343601] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (2277 - 4051) -> ( 0 - 0), size 1774 -> 0

<7> [442.343625] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [442.343791] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.343970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [442.344026] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [442.344153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [442.344370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [442.344313] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [442.344548] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.344719] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [442.344891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [442.345093] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [442.345282] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.345510] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [442.345680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] blocks 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [442.345846] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:124:plane 4A] min_ddb 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [442.346009] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [442.346168] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [442.346327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 4, 11, 11, 11, 11, 11, 0, 0, 21, 4, 21 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [442.346546] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 7, 16, 16, 16, 16, 16, 0, 0, 22, 7, 22 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [442.346735] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 2781680 num active planes 3

<7> [442.347026] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 2921 qgv_peak_bw: 38400

<7> [442.347267] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 2921 qgv_peak_bw: 38400

<7> [442.347538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [442.347827] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 2921 qgv_peak_bw: 38400

<7> [442.348078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 2921

<7> [442.348819] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [442.349103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [442.349837] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 61440 bytes of contiguous stolen space for FBC, limit: 2

<7> [442.350067] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:64:plane 2A]

<7> [442.359518] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.392559] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.392827] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 823) -> ( 0 - 597), size 823 -> 597

<7> [442.393033] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 823 - 2437) -> ( 597 - 2890), size 1614 -> 2293

<7> [442.393227] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2437 - 4051) -> (2890 - 4051), size 1614 -> 1161

<7> [442.393463] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.393650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [442.393607] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [442.393849] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [442.393948] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [442.394025] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34

<7> [442.394215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3477100 num active planes 3

<7> [442.394229] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [442.394502] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3651 qgv_peak_bw: 38400

<7> [442.394758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3651 qgv_peak_bw: 38400

<7> [442.395005] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [442.395245] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3651 qgv_peak_bw: 38400

<7> [442.395512] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3651

<7> [442.396165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [442.396446] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [442.442756] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.443124] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.443586] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 597) -> ( 0 - 904), size 597 -> 904

<7> [442.443679] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [442.443839] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 597 - 2890) -> ( 904 - 1372), size 2293 -> 468

<7> [442.444074] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (2890 - 4051) -> (1372 - 3148), size 1161 -> 1776

<7> [442.444135] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

<7> [442.444298] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb ( 0 - 0) -> (3148 - 4051), size 0 -> 903

<7> [442.444580] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.444573] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02

<7> [442.444806] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0

<7> [442.445050] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25

<7> [442.445278] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 14, 31, 31, 31, 31, 31, 0, 0, 26, 14, 26

<7> [442.445553] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.445758] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0

<7> [442.445970] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 27, 27, 27, 27, 27, 0, 0, 21, 7, 21

<7> [442.446169] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:134:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 31, 31, 31, 31, 31, 0, 0, 22, 9, 22

<7> [442.446450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 3129390 num active planes 4

<7> [442.446784] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 3286 qgv_peak_bw: 38400

<7> [442.447141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 3286 qgv_peak_bw: 38400

<7> [442.447537] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [442.447950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 3286 qgv_peak_bw: 38400

<7> [442.448299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 3286

<7> [442.449676] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off

<7> [442.450066] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00

<7> [442.458980] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:64:plane 2A]

<7> [442.476289] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.476579] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.509242] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:34:plane 1A] using Y plane [PLANE:124:plane 4A]

<7> [442.509487] xe 0000:00:02.0: [drm:intel_plane_atomic_check [xe]] UV plane [PLANE:64:plane 2A] using Y plane [PLANE:134:plane 5A]

<7> [442.509714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 904) -> ( 0 - 686), size 904 -> 686

<7> [442.509917] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:64:plane 2A] ddb ( 904 - 1372) -> ( 686 - 1372), size 468 -> 686

<7> [442.510106] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:124:plane 4A] ddb (1372 - 3148) -> (1372 - 2712), size 1776 -> 1340

<7> [442.510288] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:134:plane 5A] ddb (3148 - 4051) -> (2712 - 4051), size 903 -> 1339

<7> [442.510533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [442.510712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] lines 5, 13, 13, 13, 13, 13, 0, 0, 0, 5, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0

<7> [442.510681] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off

<7> [442.510891] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:64:plane 2A] blocks 11, 27, 27, 27, 27, 27, 0, 0, 25, 11, 25 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33

<7> [442.511023] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6

Results for igt@kms_rotation_crc@multiplane-rotation-cropping-top