Result:
i915_display_info11 igt_runner11 results11.json results11-xe-load.json guc_logs11.tar i915_display_info_post_exec11 boot11 dmesg11
| Detail | Value |
|---|---|
| Duration | 3.15 seconds |
| Hostname |
shard-lnl-5 |
| Igt-Version |
IGT-Version: 2.3-g97343920d (x86_64) (Linux: 7.0.0-rc1-lgci-xe-xe-4614-66aa2312c3791992e-debug+ x86_64) |
| Out |
Using IGT_SRANDOM=1772026202 for randomisation Opened device: /dev/dri/card0 FBC last action not supported Can't test DRRS: Not supported. Starting subtest: fbc-1p-primscrn-pri-indfb-draw-blt Subtest fbc-1p-primscrn-pri-indfb-draw-blt: SUCCESS (3.147s) |
| Err |
Starting subtest: fbc-1p-primscrn-pri-indfb-draw-blt Subtest fbc-1p-primscrn-pri-indfb-draw-blt: SUCCESS (3.147s) |
| Dmesg |
<6> [322.696418] Console: switching to colour dummy device 80x25
<6> [322.696737] [IGT] kms_frontbuffer_tracking: executing
<7> [322.702203] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]
<7> [322.702216] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [322.702394] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected
<7> [322.702649] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]
<7> [322.702652] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [322.702780] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected
<7> [322.703045] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]
<7> [322.703049] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [322.703190] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected
<7> [322.703492] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1]
<7> [322.703495] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:392:eDP-1]
<7> [322.703959] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [322.704278] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [322.704391] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [322.704500] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [322.704722] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [322.704735] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [322.704741] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [322.704744] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [322.704753] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [322.704760] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [322.704765] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD monitor
<5> [322.704773] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [322.704777] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:392:eDP-1] ELD size 20, SAD count 0
<5> [322.704784] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [322.704817] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] VRR capable: yes
<7> [322.705208] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [322.705530] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:392:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [322.706128] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [322.706131] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [322.706133] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [322.706198] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:392:eDP-1] probed modes:
<7> [322.706203] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [322.706207] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [322.706222] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1]
<7> [322.706226] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:401:DP-1]
<7> [322.706358] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:401:DP-1] disconnected
<7> [322.706370] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2]
<7> [322.706373] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:413:DP-2]
<7> [322.706491] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:413:DP-2] disconnected
<7> [322.706501] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3]
<7> [322.706504] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:421:DP-3]
<7> [322.706710] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:421:DP-3] disconnected
<7> [322.708680] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]
<7> [322.708851] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [322.709199] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [322.709385] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]
<7> [322.710507] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435]
<6> [322.712207] [IGT] kms_frontbuffer_tracking: starting subtest fbc-1p-primscrn-pri-indfb-draw-blt
<7> [322.712611] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to f
<7> [322.712717] xe 0000:00:02.0: [drm:intel_psr_debug_set [xe]] Invalid debug mask f
<7> [322.712829] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to 1
<7> [322.713020] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [322.713159] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [322.713273] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [322.713377] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [322.713465] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [322.713569] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A]
<7> [322.713698] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [fastset]
<7> [322.713796] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [322.713892] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [322.713995] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [322.714085] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [322.714173] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [322.714258] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [322.714343] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [322.714428] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [322.714511] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [322.714593] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [322.714672] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [322.714750] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [322.714827] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [322.714905] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [322.714990] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [322.715068] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [322.715145] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [322.715222] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [322.715299] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [322.715376] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [322.715452] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [322.715529] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [322.715605] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [322.715680] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [322.715755] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [322.715830] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [322.715905] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [322.716074] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [322.716161] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [322.716238] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [322.716314] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [322.716393] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [322.716471] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [322.716546] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [322.716623] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [322.716696] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [322.716769] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [322.716842] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [322.716917] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [322.717138] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [322.717231] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [322.717312] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [322.717386] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [322.717460] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [322.717533] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [322.717606] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [322.717679] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [322.717752] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [322.717823] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [322.717895] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [322.718231] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [322.718310] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:393] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [322.718390] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [322.718468] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [322.718570] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [322.718661] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [322.718789] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [322.736550] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [322.736654] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [322.743478] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]
<7> [322.743588] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [322.743695] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [322.743811] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]
<7> [322.744268] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:435]
<7> [322.853114] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [322.853269] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [322.853600] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [322.853884] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [322.854206] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [322.854489] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [322.854778] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [322.855097] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [322.855379] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [322.855676] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [322.855984] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [322.856275] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [322.856574] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [322.856932] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [322.857328] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [322.857668] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [322.857971] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [322.858253] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [322.858575] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [322.858839] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [322.859128] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [322.859389] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [322.859654] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [322.859892] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [322.860213] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [322.860468] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [322.860709] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [322.860961] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [322.861235] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [322.861471] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [322.861707] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [322.861938] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [322.862224] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [322.862461] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [322.862693] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [322.862928] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [322.863232] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [322.863504] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [322.863763] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [322.864133] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [322.864354] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:150:pipe A] releasing DPLL 0
<7> [322.864667] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [322.864897] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [322.865178] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [322.865359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [322.865531] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [322.865691] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [322.865856] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [322.866041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [322.866216] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [322.866447] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [322.866670] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [322.866878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [322.867158] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [322.867363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [322.867561] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [322.867787] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [322.868002] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [322.868181] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [322.868353] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [322.868552] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: no [modeset]
<7> [322.868758] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [NOFB], visible: no
<7> [322.868938] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [322.869134] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [322.869319] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [322.869495] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [322.869651] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [322.869925] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [322.870091] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [323.072059] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 0
<7> [323.072547] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [323.093872] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power off
<7> [323.094284] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [323.094407] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [323.094816] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [323.094813] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [323.145872] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [323.146291] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:150:pipe A]
<7> [323.146344] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [323.146752] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [323.147046] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - short
<7> [323.147416] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [323.147698] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [323.148147] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [323.148626] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:391:DDI A/PHY A]
<7> [323.148963] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:400:DDI TC1/PHY TC1]
<7> [323.149253] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST A]
<7> [323.149548] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST B]
<7> [323.149848] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST C]
<7> [323.150248] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:412:DDI TC2/PHY TC2]
<7> [323.150578] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST A]
<7> [323.150867] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST B]
<7> [323.151203] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST C]
<7> [323.151538] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:420:DDI TC3/PHY TC3]
<7> [323.151853] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST A]
<7> [323.152173] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST B]
<7> [323.152485] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST C]
<7> [323.152761] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [323.153183] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [323.153497] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [323.153798] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [323.154325] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [323.154717] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating disabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xaa000000)
<7> [323.155242] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [323.155599] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [323.156016] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [323.156305] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [323.162450] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [323.165582] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:388:pipe C]
<7> [323.176059] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:428]
<7> [323.184302] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [323.184449] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [323.184572] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [323.184697] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [323.184964] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [323.185174] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [323.185337] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [323.198675] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [323.198715] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [323.198827] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [323.199048] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [323.199143] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [323.199233] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [323.199319] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [323.199410] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A]
<7> [323.199500] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [323.199585] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [323.199670] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [323.199754] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [323.199837] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [323.199920] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [323.200019] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [323.200102] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [323.200185] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [323.200265] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [323.200347] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [323.200428] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [323.200507] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [323.200587] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [323.200668] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [323.200747] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [323.200828] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [323.200909] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [323.201001] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [323.201081] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [323.201159] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [323.201237] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [323.201315] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [323.201391] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [323.201469] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [323.201545] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [323.201621] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [323.201695] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [323.201769] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [323.201842] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [323.201915] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [323.202002] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [323.202075] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [323.202148] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [323.202222] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [323.202294] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [323.202366] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [323.202438] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:150:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [323.202510] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] fastset requirement not met, forcing full modeset
<7> [323.202618] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [323.202683] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:150:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [323.202769] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [323.202835] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:144:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [323.202898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [323.202965] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [323.203020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [323.203073] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [323.203139] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [323.203235] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [323.203321] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [323.203399] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [323.203478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [323.203556] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [323.203634] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:150:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [323.203726] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [323.203813] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [323.203901] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [323.203993] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [323.204084] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:150:pipe A] allocated DPLL 0
<7> [323.204160] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:150:pipe A] reserving DPLL 0
<7> [323.204238] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [modeset]
<7> [323.204322] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [323.204404] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [323.204484] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [323.204564] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [323.204643] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [323.204721] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [323.204798] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [323.204874] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [323.204956] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [323.205033] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [323.205115] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [323.205198] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [323.205280] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [323.205356] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [323.205431] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [323.205504] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [323.205579] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [323.205652] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [323.205725] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [323.205798] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [323.205871] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [323.205958] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [323.206044] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [323.206129] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [323.206210] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [323.206282] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [323.206351] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [323.206421] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [323.206492] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [323.206562] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [323.206634] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [323.206705] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [323.206776] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [323.206846] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [323.206917] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [323.207006] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [323.207082] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [323.207158] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [323.207234] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [323.207309] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [323.207385] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [323.207460] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [323.207534] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [323.207607] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [323.207679] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [323.207751] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [323.207824] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [323.207895] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [323.207984] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [323.208058] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [323.208129] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [323.208200] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:428] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x100000000000001, visible: yes
<7> [323.208274] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [323.208346] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [323.208419] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:64:plane 2A] fb: [NOFB], visible: no
<7> [323.208492] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:94:plane 3A] fb: [NOFB], visible: no
<7> [323.208564] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:124:plane 4A] fb: [NOFB], visible: no
<7> [323.208636] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:134:plane 5A] fb: [NOFB], visible: no
<7> [323.208707] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:144:cursor A] fb: [NOFB], visible: no
<7> [323.209151] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [323.209255] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [323.209390] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [323.209534] xe 0000:00:02.0: [drm:dss_pipe_gating_enable_disable [xe]] DSS clock gating enabled for pipe_mask=0x1 (CLKGATE_DIS_DSSDSC=0xa8000000)
<7> [323.209635] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [323.209728] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [323.209814] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [323.209897] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:391:DDI A/PHY A]
<7> [323.209980] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:400:DDI TC1/PHY TC1]
<7> [323.210047] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST A]
<7> [323.210112] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST B]
<7> [323.210175] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:404:DP-MST C]
<7> [323.210237] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:412:DDI TC2/PHY TC2]
<7> [323.210300] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST A]
<7> [323.210359] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST B]
<7> [323.210419] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:416:DP-MST C]
<7> [323.210479] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:420:DDI TC3/PHY TC3]
<7> [323.210539] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST A]
<7> [323.210597] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST B]
<7> [323.210658] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:424:DP-MST C]
<7> [323.210742] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [323.210899] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [323.210980] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [323.211090] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [323.212031] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:150:pipe A]
<7> [323.212142] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [323.214083] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turn panel power on
<7> [323.214169] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power cycle (433 ms remaining)
<7> [323.656113] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [323.752015] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [323.752111] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [323.752254] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [323.752387] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [323.752490] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 wait for panel power on
<7> [323.752981] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [323.789383] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [323.789893] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:391:DDI A/PHY A] - long
<7> [323.790278] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [323.790762] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:391:DDI A/PHY A]
<7> [323.963098] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [323.963573] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 turning VDD on
<7> [323.964002] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:391:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [323.966194] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [323.967756] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [323.968633] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [323.969846] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [323.971284] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [323.972476] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Clock recovery OK
<7> [323.972837] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [323.974364] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [323.974754] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:392:eDP-1][ENCODER:391:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [323.975753] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [323.976297] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [323.976627] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [323.977009] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:392:eDP-1] set backlight PWM = 4518
<7> [323.993563] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [323.994069] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<7> [323.998080] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [324.026952] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [324.027466] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [324.027948] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [324.060839] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [324.061378] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [324.077753] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:428] from all active usage due to RMFB ioctl
<7> [324.077866] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:428] is removed
<7> [324.078029] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [324.078381] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [324.078686] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [324.079011] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [324.079284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [324.079655] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [324.080146] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [324.080551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [324.080951] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [324.081367] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [324.081750] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [324.110931] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [324.111214] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [324.111429] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [324.117492] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:428]
<7> [324.118378] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]
<7> [324.131306] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439]
<7> [324.138782] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:440]
<7> [324.243886] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [324.244128] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [324.343289] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [324.343375] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [324.343540] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [324.343835] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [324.344178] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [324.344447] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [324.344769] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [324.345169] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [324.345564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [324.345960] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [324.346333] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [324.346701] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [324.347163] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [324.366552] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [324.372390] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:388:pipe C]
<7> [324.394336] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [324.394819] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [324.426909] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [324.427390] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [324.427812] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [324.460853] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [324.461300] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [324.477052] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [324.477176] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [324.493719] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [324.526899] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [324.527441] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [324.527929] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [324.560812] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [324.561316] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [324.577009] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [324.577124] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [324.593585] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [324.626911] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [324.627396] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [324.627807] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [324.660782] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [324.661360] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [324.676874] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [324.676987] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [324.693607] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [324.726906] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [324.727413] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [324.727839] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [324.760838] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [324.761320] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [324.784644] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:440] from all active usage due to RMFB ioctl
<7> [324.784755] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:440] is removed
<7> [324.784913] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [324.785274] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [324.785606] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [324.785972] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [324.786318] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [324.786667] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [324.787372] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [324.787865] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [324.788295] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [324.788672] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [324.789058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [324.909995] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A]
<7> [324.910110] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:392:eDP-1]
<7> [324.910359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [324.910741] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [324.911076] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [324.911342] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [324.911596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [324.911944] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [324.912359] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [324.912737] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [324.913122] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [324.913478] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [324.913828] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [324.916919] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 14745600 bytes of contiguous stolen space for FBC, limit: 2
<7> [324.917250] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A]
<7> [324.933976] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [324.939003] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:388:pipe C]
<7> [324.961703] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [324.962461] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [324.993893] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [324.994426] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [324.994899] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.027436] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.027989] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.046531] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [325.076887] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.077394] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.077903] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.110891] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.111472] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.143866] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.143935] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [325.144282] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.144598] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.146093] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.146447] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.176892] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.177473] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.178028] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.210704] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.211321] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.230277] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [325.260880] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.261413] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.261898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.294152] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.294881] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.326555] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [325.326912] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.327267] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.327542] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.328502] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.328796] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.360868] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.361444] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.361995] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.394335] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.395018] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.413320] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [325.443872] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.444336] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.444747] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.477452] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.478000] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.510742] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [325.511078] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.511355] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.511593] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.512629] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.512966] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.543873] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.544369] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.544854] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.577309] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.577876] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.596853] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [325.626857] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.627348] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.627788] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.661028] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.661719] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.693928] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [325.693965] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.694390] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.694736] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.695883] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.696239] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.726860] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.727373] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.727870] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.760633] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.761262] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [325.779589] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [325.810917] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [325.811501] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [325.811977] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [325.843889] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [325.844489] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<6> [325.862157] [IGT] kms_frontbuffer_tracking: finished subtest fbc-1p-primscrn-pri-indfb-draw-blt, SUCCESS
<7> [325.864585] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:431] from all active usage due to RMFB ioctl
<7> [325.864754] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:34:plane 1A] because [FB:431] is removed
<7> [325.865031] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [325.865488] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [325.865875] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [325.866204] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [325.866517] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [325.866914] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 0 num active planes 0
<7> [325.867442] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [325.867969] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [325.868460] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [325.868981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [325.869470] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [325.876051] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A]
<7> [325.905085] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:34:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [325.905292] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [325.905436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [325.905567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [325.905688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:34:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [325.905856] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:150:pipe A] data rate 1390840 num active planes 1
<7> [325.906044] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [325.906217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [325.906380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [325.906541] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [325.906706] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [325.909766] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 11059200 bytes of contiguous stolen space for FBC, limit: 2
<7> [325.909940] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:34:plane 1A]
<7> [325.926234] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [325.928236] [IGT] kms_frontbuffer_tracking: exiting, ret=0
<7> [325.928772] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to 0
<7> [325.929388] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:392:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [325.929720] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:391:DDI A/PHY A][CRTC:150:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [325.930862] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 HDR no link rate required 1303913 available 1728000
<7> [325.931166] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:150:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [325.931403] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:391:DDI A/PHY A] [CRTC:150:pipe A]
<7> [325.931769] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:150:pipe A] enable: yes [fastset]
<7> [325.932082] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [325.932291] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [325.932490] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [325.932692] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [325.932905] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [325.933104] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [325.933294] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [325.933479] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [325.933662] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [325.933964] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [325.934138] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [325.934298] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [325.934444] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [325.934589] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [325.934728] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [325.934881] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [325.935030] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [325.935172] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [325.935318] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [325.935450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [325.935595] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [325.935727] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [325.935905] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [325.936051] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [325.936179] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [325.936301] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [325.936423] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [325.936551] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [325.936676] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [325.936805] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [325.936922] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [325.937031] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [325.937139] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [325.937246] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [325.937354] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [325.937471] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: fracen: no,
<7> [325.937594] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [325.937709] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [325.937859] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [325.937983] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [325.938108] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [325.938227] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [325.938347] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [325.938475] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [325.938593] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [325.938709] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [325.938837] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [325.938951] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [325.939060] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [325.939166] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [325.939270] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [325.939375] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [325.939479] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [325.939585] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [325.939697] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [325.939820] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [325.939933] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [325.940046] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:34:plane 1A] fb: [FB:393] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [325.940162] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [325.940283] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [325.942681] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:34:plane 1A]
<7> [325.959409] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [325.961060] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:392:eDP-1]
<7> [325.961561] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:150:pipe A]
<6> [325.976341] Console: switching to colour frame buffer device 180x56
|