Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

i915_display_info23 igt_runner23 results23.json results23-xe-load.json guc_logs23.tar i915_display_info_post_exec23 boot23 dmesg23

DetailValue
Duration 1.44 seconds
Hostname 
shard-lnl-1
Igt-Version 
IGT-Version: 2.3-gc45426aaf (x86_64) (Linux: 6.19.0-rc5-lgci-xe-xe-4389-7c343f3950a354458+ x86_64)
Out 
Using IGT_SRANDOM=1768541655 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.444s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.444s)
Dmesg
<6> [410.063529] Console: switching to colour dummy device 80x25
<6> [410.063779] [IGT] kms_pm_rpm: executing
<7> [410.069161] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [410.069171] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [410.069318] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [410.069408] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [410.069690] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [410.069694] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [410.069819] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [410.069902] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [410.070109] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [410.070111] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [410.070218] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [410.070297] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [410.070575] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]
<7> [410.070579] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]
<7> [410.071042] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [410.071353] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [410.071469] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [410.071571] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [410.071697] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [410.071703] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [410.071705] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [410.071706] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [410.071709] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [410.071711] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [410.071713] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor
<5> [410.071716] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [410.071717] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0
<5> [410.071720] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [410.071732] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes
<7> [410.071817] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [410.071895] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [410.072399] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [410.072401] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [410.072402] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [410.072466] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:
<7> [410.072471] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [410.072475] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [410.072488] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [410.072492] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [410.072633] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [410.072645] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [410.072648] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [410.072777] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [410.072787] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [410.072790] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [410.072906] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [410.072920] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]
<7> [410.072922] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]
<7> [410.073348] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [410.073658] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [410.073757] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [410.073867] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [410.073982] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [410.073985] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [410.073987] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [410.073989] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [410.073991] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [410.073993] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [410.073995] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor
<5> [410.073997] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [410.073999] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0
<5> [410.074002] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [410.074009] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes
<7> [410.074089] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [410.074162] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [410.074671] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [410.074673] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [410.074675] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [410.074715] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:
<7> [410.074719] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [410.074723] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [410.074762] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [410.074766] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [410.074900] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [410.074937] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [410.074940] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [410.075058] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [410.075090] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [410.075093] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [410.075209] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [410.089330] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:428]
<7> [411.103554] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [411.103569] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [411.103689] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [411.124541] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [411.124805] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [411.125168] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [411.125468] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [411.125741] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [411.126005] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [411.126255] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [411.126504] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [411.126741] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [411.127006] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [411.127246] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [411.127558] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [411.127798] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [411.128035] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [411.128275] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [411.128549] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [411.128850] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [411.129099] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [411.129369] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [411.129680] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [411.129999] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [411.130280] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [411.130598] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [411.130885] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [411.131181] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [411.131495] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [411.131801] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [411.132102] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [411.132403] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [411.132751] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [411.133050] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [411.133347] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [411.133681] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [411.133953] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [411.134223] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [411.134491] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [411.134783] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [411.135031] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [411.135275] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [411.135543] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [411.135782] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:149:pipe A] releasing DPLL 0
<7> [411.136096] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [411.136307] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [411.136543] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [411.136706] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [411.136864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [411.137041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [411.137207] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [411.137361] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [411.137563] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [411.137781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [411.137988] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [411.138217] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [411.138426] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [411.138642] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [411.138825] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [411.139059] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [411.139233] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [411.139401] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [411.139582] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [411.139775] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: no [modeset]
<7> [411.139934] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [NOFB], visible: no
<7> [411.140087] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [411.140238] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [411.140383] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [411.140564] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [411.140727] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [411.140938] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [411.141723] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [411.141912] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [411.142658] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [411.142780] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [411.351639] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 0
<7> [411.352086] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [411.363006] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power off
<7> [411.363325] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [411.363454] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [411.363696] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [411.364080] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [411.416122] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [411.416662] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [411.423532] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [411.423952] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:149:pipe A]
<7> [411.424002] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [411.424498] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [411.425268] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [411.425776] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [411.426306] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [411.426675] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [411.426980] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [411.427331] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [411.427656] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [411.427949] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [411.428260] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [411.428566] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [411.428875] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [411.429142] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [411.429406] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [411.429789] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [411.430071] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [411.430329] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [411.430714] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [411.430995] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [411.431279] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [411.431803] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [411.432281] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [411.432632] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [411.433039] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [411.433323] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [411.434243] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [411.434670] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [411.452527] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [411.452991] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [411.453400] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [411.453901] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [411.453918] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [411.454311] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [411.454686] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [411.455201] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [411.457854] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspending
<7> [411.459950] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled
<7> [411.460859] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspended
<7> [411.461210] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspending
<7> [411.461725] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled
<7> [411.462074] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspended
<6> [411.537553] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [411.572324] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resuming
<7> [411.572988] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled
<7> [411.574344] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resumed
<7> [411.574539] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resuming
<7> [411.574871] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled
<7> [411.574999] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resumed
<7> [411.576330] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [411.576558] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [411.576740] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [411.576872] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [411.577027] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [411.577145] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [411.577292] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [411.577409] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [411.577601] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [411.577875] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [411.578106] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [411.578231] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [411.595529] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [411.596019] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [411.596424] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [412.639589] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [412.639710] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [412.639730] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [412.640049] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [412.640086] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspending
<7> [412.640587] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled
<7> [412.640800] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspended
<7> [412.640991] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspending
<7> [412.641287] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled
<7> [412.641505] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspended
<7> [412.694076] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resuming
<7> [412.694844] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled
<7> [412.695505] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resumed
<7> [412.695798] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resuming
<7> [412.696119] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled
<7> [412.696474] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resumed
<7> [412.697092] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [412.697570] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [412.698028] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [412.698389] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [412.698874] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [412.699212] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [412.699668] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [412.700028] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [412.700135] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:391:eDP-1]
<7> [412.700442] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [412.700947] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [412.701348] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [412.701785] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [412.702182] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [412.702594] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [412.702982] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [412.703391] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [412.703847] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [412.704278] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [412.704691] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [412.705110] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [412.705485] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [412.705889] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [412.706244] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [412.706591] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [412.706903] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [412.707213] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [412.707517] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [412.707799] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [412.708060] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [412.708327] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [412.708608] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [412.708878] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [412.709114] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [412.709344] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [412.709591] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [412.709801] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [412.710015] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [412.710219] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [412.710419] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [412.710645] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [412.710834] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [412.711015] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [412.711191] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [412.711362] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [412.711552] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [412.711740] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [412.711904] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [412.712057] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [412.712207] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [412.712351] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [412.712507] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [412.712647] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [412.712858] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [412.712966] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [412.713103] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [412.713206] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [412.713308] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [412.713405] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [412.713523] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [412.713617] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [412.713736] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [412.713897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [412.714042] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [412.714165] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [412.714286] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [412.714406] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [412.714537] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [412.714678] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [412.714790] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [412.714895] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [412.714998] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [412.715138] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:149:pipe A] allocated DPLL 0
<7> [412.715251] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:149:pipe A] reserving DPLL 0
<7> [412.715362] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [modeset]
<7> [412.715473] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [412.715573] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [412.715669] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [412.715760] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [412.715850] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [412.715938] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [412.716024] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [412.716113] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [412.716202] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [412.716298] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [412.716382] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [412.716471] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [412.716553] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [412.716633] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [412.716711] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [412.716791] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [412.716869] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [412.716947] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [412.717025] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [412.717106] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [412.717185] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [412.717263] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [412.717343] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [412.717420] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [412.717509] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [412.717587] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [412.717663] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [412.717739] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [412.717815] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [412.717890] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [412.717958] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [412.718028] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [412.718106] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [412.718184] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [412.718262] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [412.718338] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [412.718413] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [412.718501] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [412.718580] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [412.718657] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [412.718735] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [412.718807] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [412.718877] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [412.718953] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [412.719033] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [412.719110] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [412.719186] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [412.719264] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [412.719340] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [412.719416] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [412.719505] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [412.719582] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [412.719656] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [412.719730] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [412.719799] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [412.719873] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [412.719949] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [412.720024] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:428] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [412.720100] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [412.720175] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [412.720250] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [412.720329] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [412.720406] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [412.720489] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [412.720565] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [412.722778] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [412.723025] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [412.723161] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [412.723306] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [412.723399] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [412.723501] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [412.723598] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [412.723678] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [412.723752] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [412.723821] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [412.723888] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [412.723957] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [412.724022] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [412.724081] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [412.724138] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [412.724194] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [412.724252] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [412.724323] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [412.724389] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [412.724486] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [412.724650] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [412.724715] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [412.724825] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [412.725550] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:149:pipe A]
<7> [412.725679] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [412.727390] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power on
<7> [412.727480] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [412.727587] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [412.737503] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [412.737597] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power on
<7> [412.737693] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [412.774211] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [412.774779] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [412.775210] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [412.775746] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [412.947908] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [412.948246] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on
<7> [412.948551] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [412.950556] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [412.951832] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [412.952585] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [412.953710] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [412.954819] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [412.955916] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Clock recovery OK
<7> [412.956257] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [412.957735] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [412.958044] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [412.958867] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [412.959375] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [412.959817] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [412.960309] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 4518
<7> [412.976237] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [412.977940] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [412.978294] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<6> [412.982745] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [412.984136] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:428] from all active usage due to RMFB ioctl
<7> [412.984223] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:428] is removed
<7> [412.984333] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [412.984663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [412.984900] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [412.985129] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [412.985365] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [412.985680] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [412.986058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [412.986385] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [412.986725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [412.987024] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [412.987366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [412.988158] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [412.997908] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [412.998136] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [412.998332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [412.998567] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [412.998761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [412.998983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [412.999314] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [412.999652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [412.999998] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [413.000297] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [413.000626] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [413.009479] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [413.011381] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [413.012261] [IGT] kms_pm_rpm: exiting, ret=0
<6> [413.026841] Console: switching to colour frame buffer device 180x56
<7> [413.043504] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [413.043912] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [413.044253] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [413.044667] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [413.045094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [413.077594] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [413.078016] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [413.078362] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
Created at 2026-01-16 05:53:43