Results for igt@kms_frontbuffer_tracking@plane-fbc-rte

Result: Pass

i915_display_info1 igt_runner1 results1.json results1-xe-load.json guc_logs1.tar i915_display_info_post_exec1 boot1 dmesg1

DetailValue
Duration 4.84 seconds
Hostname
shard-lnl-5
Igt-Version
IGT-Version: 2.3-g726612327 (x86_64) (Linux: 6.19.0-rc5-lgci-xe-xe-4368-e9383891a008f23b4+ x86_64)
Out
Using IGT_SRANDOM=1768248104 for randomisation
Opened device: /dev/dri/card0
FBC last action not supported
Can't test DRRS: Not supported.
Starting subtest: plane-fbc-rte
FBC is not enabled: 
FBC disabled: disabled per module param or by default
  [PLANE:33:plane 1A]: plane not visible
  [PLANE:63:plane 2A]: plane not
Testing fbc on plane 1A
Testing fbc on plane 2A
Testing fbc on plane 3A
Subtest plane-fbc-rte: SUCCESS (4.836s)
Err
Starting subtest: plane-fbc-rte
Subtest plane-fbc-rte: SUCCESS (4.836s)
Dmesg
<6> [157.034427] Console: switching to colour dummy device 80x25
<6> [157.034612] [IGT] kms_frontbuffer_tracking: executing
<7> [157.043182] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [157.043193] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [157.043377] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [157.043663] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [157.043666] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [157.043836] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [157.044130] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [157.044135] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [157.044282] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [157.044605] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]
<7> [157.044607] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]
<7> [157.045068] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [157.045382] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [157.045489] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [157.045594] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [157.045709] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [157.045713] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [157.045715] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [157.045716] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [157.045718] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [157.045720] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [157.045721] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor
<5> [157.045723] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [157.045724] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0
<5> [157.045726] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [157.045910] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes
<7> [157.046087] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [157.046408] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [157.047165] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [157.047168] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [157.047170] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [157.047232] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:
<7> [157.047236] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [157.047240] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [157.047254] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [157.047257] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [157.047405] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [157.047416] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [157.047418] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [157.047530] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [157.047539] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [157.047541] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [157.047654] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [157.051894] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [157.052049] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]
<7> [157.052179] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [157.052310] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [157.052878] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]
<6> [157.053355] [IGT] kms_frontbuffer_tracking: starting subtest plane-fbc-rte
<7> [157.053679] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to f
<7> [157.053847] xe 0000:00:02.0: [drm:intel_psr_debug_set [xe]] Invalid debug mask f
<7> [157.053962] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to 1
<7> [157.054122] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [157.054225] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [157.054315] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [157.054401] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [157.054470] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [157.054561] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [157.054683] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset]
<7> [157.054791] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [157.054900] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [157.055007] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [157.055095] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [157.055182] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [157.055271] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [157.055358] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [157.055450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [157.055552] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [157.055653] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [157.055755] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [157.055854] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [157.055951] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [157.056047] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [157.056128] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [157.056208] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [157.056289] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [157.056368] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [157.056448] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [157.056525] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [157.056597] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [157.056669] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [157.056753] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [157.056848] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [157.056941] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [157.057033] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [157.057125] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [157.057217] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [157.057289] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [157.057360] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [157.057430] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [157.057504] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [157.057579] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [157.057655] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [157.057731] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [157.057840] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [157.057931] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [157.058022] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [157.058100] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [157.058180] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [157.058259] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [157.058338] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.058416] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.058493] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.058570] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [157.058647] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [157.058722] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.058824] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.058916] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.059007] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [157.059097] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [157.059187] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:392] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [157.059278] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [157.059354] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [157.059451] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [157.059539] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [157.059681] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [157.083348] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [157.083546] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [157.090294] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [157.090438] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]
<7> [157.090583] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [157.090719] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [157.091215] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]
<7> [157.199979] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [157.200174] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [157.200609] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [157.201058] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [157.201446] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [157.201856] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [157.202239] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [157.202609] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [157.203012] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [157.203434] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [157.203808] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [157.204226] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [157.204635] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [157.205035] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [157.205398] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [157.205808] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [157.206210] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [157.206566] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [157.206973] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [157.207313] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [157.207646] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [157.208059] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [157.208417] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [157.208799] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [157.209121] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [157.209480] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [157.209816] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [157.210135] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [157.210450] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [157.210982] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [157.211292] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [157.211600] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [157.212001] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [157.212302] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [157.212583] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [157.212915] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [157.213188] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [157.213449] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [157.213695] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [157.213974] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [157.214216] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:149:pipe A] releasing DPLL 0
<7> [157.214554] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [157.214777] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [157.214995] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [157.215160] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [157.215310] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [157.215458] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [157.215602] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [157.215749] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [157.215925] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [157.216134] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [157.216335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [157.216525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [157.216769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [157.216967] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [157.217140] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [157.217370] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [157.217537] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [157.217694] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [157.217881] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [157.217892] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [157.218070] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: no [modeset]
<7> [157.218118] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [157.218219] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [NOFB], visible: no
<7> [157.218294] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [157.218366] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [157.218507] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [157.218646] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [157.218818] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [157.218973] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [157.219151] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [157.219301] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [157.219569] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [157.219691] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [157.422951] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 0
<7> [157.423687] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [157.434326] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power off
<7> [157.434784] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [157.434743] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [157.435236] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [157.435382] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [157.486393] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [157.486787] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:149:pipe A]
<7> [157.486786] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [157.487111] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [157.487560] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [157.487992] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [157.488043] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [157.488398] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [157.488861] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [157.489163] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [157.489437] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [157.489705] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [157.490105] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [157.490399] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [157.490677] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [157.491005] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [157.491334] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [157.491626] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [157.491953] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [157.492218] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [157.492479] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [157.492761] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [157.493139] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [157.493405] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [157.493670] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [157.494247] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [157.494798] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [157.495144] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [157.495545] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [157.495885] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [157.502153] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [157.505671] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [157.510838] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:427]
<7> [157.523902] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [157.524053] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [157.524150] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [157.524255] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [157.525789] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [157.525977] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [157.526103] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [157.530014] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [157.530048] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:391:eDP-1]
<7> [157.530130] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [157.530285] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [157.530377] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [157.530464] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [157.530546] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [157.530636] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [157.530723] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [157.530853] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [157.530963] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [157.531068] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [157.531158] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [157.531238] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [157.531318] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [157.531397] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [157.531475] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [157.531553] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [157.531630] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [157.531709] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [157.531812] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [157.531915] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [157.532016] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [157.532103] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [157.532186] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [157.532267] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [157.532344] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [157.532421] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [157.532495] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [157.532571] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [157.532645] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [157.532718] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [157.532821] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [157.532917] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [157.533011] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [157.533101] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [157.533175] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [157.533247] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [157.533317] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [157.533388] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [157.533457] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [157.533527] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [157.533599] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [157.533669] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [157.533743] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [157.533832] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [157.533934] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [157.534090] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [157.534151] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [157.534234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [157.534293] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [157.534348] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [157.534402] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [157.534455] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [157.534507] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [157.534582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [157.534666] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [157.534751] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [157.534853] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [157.534955] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [157.535052] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [157.535134] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [157.535231] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [157.535309] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [157.535384] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [157.535459] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [157.535558] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:149:pipe A] allocated DPLL 0
<7> [157.535632] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:149:pipe A] reserving DPLL 0
<7> [157.535707] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [modeset]
<7> [157.535808] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [157.535911] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [157.536011] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [157.536098] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [157.536178] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [157.536255] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [157.536331] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [157.536406] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [157.536480] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [157.536553] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [157.536625] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [157.536698] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [157.536786] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [157.536882] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [157.536975] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [157.537062] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [157.537136] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [157.537207] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [157.537278] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [157.537349] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [157.537419] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [157.537495] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [157.537576] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [157.537656] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [157.537738] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [157.537827] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [157.537916] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [157.538005] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [157.538086] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [157.538155] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [157.538223] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [157.538292] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [157.538359] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [157.538428] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [157.538497] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [157.538566] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [157.538636] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [157.538708] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [157.538810] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [157.538906] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [157.538999] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [157.539081] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.539157] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.539227] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.539297] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [157.539366] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [157.539436] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.539506] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.539574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [157.539643] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [157.539710] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [157.539801] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:427] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x100000000000001, visible: yes
<7> [157.539903] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [157.540005] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [157.540097] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [157.540168] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [157.540236] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [157.540305] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [157.540373] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [157.540742] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [157.541020] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [157.541170] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [157.541315] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [157.541407] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [157.541491] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [157.541571] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [157.541636] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [157.541698] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [157.541779] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [157.541861] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [157.541940] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [157.542016] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [157.542082] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [157.542139] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [157.542196] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [157.542252] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [157.542309] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [157.542368] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [157.542448] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [157.542603] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [157.542662] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [157.542776] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [157.543835] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:149:pipe A]
<7> [157.543964] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [157.545687] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power on
<7> [157.545778] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power cycle (441 ms remaining)
<7> [157.990989] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [158.011683] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [158.012207] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power on
<7> [158.012609] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [158.048851] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [158.049302] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [158.049636] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [158.049982] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [158.095054] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [158.095031] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [158.095137] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [158.222918] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [158.223429] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on
<7> [158.223891] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [158.226163] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [158.227494] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [158.228388] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [158.229552] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [158.230841] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [158.231977] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Clock recovery OK
<7> [158.232354] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [158.233882] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [158.234282] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [158.235238] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [158.235716] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [158.236101] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [158.236463] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 13892
<7> [158.252959] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [158.253405] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [158.257543] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [158.286914] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [158.287458] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [158.288003] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [158.320693] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [158.321272] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [158.336917] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:427] from all active usage due to RMFB ioctl
<7> [158.337012] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:427] is removed
<7> [158.337099] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [158.337380] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [158.337625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [158.337934] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [158.338180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [158.338515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [158.338943] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [158.339335] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [158.339715] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [158.340205] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [158.340615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [158.452774] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [158.452991] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [158.453457] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [158.453961] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [158.454400] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [158.454849] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [158.455269] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [158.455682] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [158.456130] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [158.456548] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [158.456961] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [158.457365] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [158.457756] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [158.458124] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [158.458481] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [158.458855] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [158.459211] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [158.459560] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [158.460012] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [158.460397] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [158.460825] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [158.461173] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [158.461512] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [158.461917] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [158.462296] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [158.462671] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [158.463236] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [158.463580] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [158.463931] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [158.464266] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [158.464564] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [158.464923] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [158.465228] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [158.465528] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [158.465822] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [158.466101] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [158.466392] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [158.466647] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [158.466949] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [158.467190] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [158.467462] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:149:pipe A] releasing DPLL 0
<7> [158.467854] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [158.468041] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [158.468252] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [158.468470] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [158.468703] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [158.468965] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [158.469179] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [158.469426] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: no [modeset]
<7> [158.469633] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [NOFB], visible: no
<7> [158.469864] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [158.469893] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [158.470053] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [158.470213] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [158.470228] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [158.470401] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [158.470416] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [158.470565] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [158.470831] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [158.471006] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [158.471315] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [158.471470] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [158.678899] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 0
<7> [158.679565] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [158.690266] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power off
<7> [158.690592] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [158.690698] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [158.690955] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [158.691410] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [158.743109] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [158.743728] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [158.750787] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [158.751283] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:149:pipe A]
<7> [158.751340] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [158.752057] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [158.752678] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [158.753251] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [158.754798] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [158.755182] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [158.755520] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [158.755941] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [158.756264] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [158.756638] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [158.757037] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [158.757316] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [158.757591] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [158.757930] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [158.758230] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [158.758521] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [158.758843] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [158.759103] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [158.759466] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [158.759739] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [158.760000] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [158.760536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [158.761041] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [158.761386] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [158.761809] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [158.762100] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [158.767751] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [158.770713] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [158.779655] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [158.779842] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [158.779972] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [158.780110] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [158.791778] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [158.792176] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [158.792544] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [158.792940] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [160.901188] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436]
<7> [160.908170] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [160.908305] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [160.908405] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [160.908500] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [160.908583] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [160.908673] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [160.908794] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [160.908907] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [160.909019] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [160.909108] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [160.909193] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [160.909276] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [160.909359] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [160.909444] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [160.909525] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [160.909605] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [160.909684] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [160.909788] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [160.909888] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [160.909987] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [160.910076] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [160.910150] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [160.910224] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [160.910298] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [160.910371] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [160.910443] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [160.910515] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [160.910587] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [160.910659] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [160.910740] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [160.910833] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [160.910925] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [160.911016] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [160.911087] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [160.911162] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [160.911239] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [160.911316] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [160.911393] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [160.911469] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [160.911546] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [160.911622] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [160.911697] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [160.911808] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [160.911899] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [160.911989] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [160.912212] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [160.912287] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [160.912443] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [160.912528] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [160.912606] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [160.912680] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [160.912760] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [160.912862] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [160.912967] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [160.913055] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [160.913130] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [160.913204] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [160.913278] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [160.913353] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [160.913426] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [160.913499] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [160.913572] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [160.913644] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [160.913723] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [160.913817] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [160.913918] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [160.914012] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [160.914085] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [160.914157] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [160.914229] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [160.914300] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [160.914371] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [160.914444] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [160.914517] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [160.914591] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [160.914663] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [160.914751] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [160.914846] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [160.914939] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [160.915025] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [160.915095] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [160.915164] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [160.915233] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [160.915302] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [160.915371] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [160.915440] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [160.915508] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [160.915576] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [160.915645] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [160.915719] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [160.915808] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [160.915906] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [160.916024] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [160.916087] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [160.916273] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [160.916329] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [160.916383] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [160.916437] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [160.916490] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [160.916542] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [160.916615] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [160.916697] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [160.916815] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [160.916928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [160.917027] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [160.917103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [160.917180] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [160.917278] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [160.917354] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [160.917429] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [160.917523] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:149:pipe A] allocated DPLL 0
<7> [160.917597] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:149:pipe A] reserving DPLL 0
<7> [160.917676] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [modeset]
<7> [160.917944] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [160.918040] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [160.918118] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [160.918194] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [160.918270] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [160.918345] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [160.918418] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [160.918492] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [160.918565] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [160.918639] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [160.918716] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [160.918809] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [160.918902] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [160.918994] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [160.919069] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [160.919139] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [160.919208] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [160.919278] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [160.919348] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [160.919418] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [160.919488] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [160.919559] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [160.919629] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [160.919698] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [160.919801] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [160.919891] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [160.919981] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [160.920059] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [160.920133] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [160.920207] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [160.920282] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [160.920355] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [160.920429] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [160.920503] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [160.920577] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [160.920652] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [160.920802] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [160.920898] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [160.920995] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [160.921076] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [160.921155] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [160.921233] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [160.921310] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [160.921386] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [160.921462] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [160.921538] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [160.921615] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [160.921691] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [160.921802] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [160.921894] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [160.921983] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [160.922073] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:436] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x100000000000001, visible: yes
<7> [160.922149] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [160.922224] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [160.922299] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [160.922373] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [160.922447] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [160.922521] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [160.922593] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [160.923055] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [160.923140] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [160.923376] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [160.923521] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [160.923672] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [160.923794] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [160.923899] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [160.924004] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [160.924070] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [160.924138] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [160.924204] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [160.924270] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [160.924334] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [160.924398] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [160.924461] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [160.924523] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [160.924585] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [160.924651] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [160.924722] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [160.924799] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [160.924907] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [160.925098] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [160.925170] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [160.925282] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [160.926606] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:149:pipe A]
<7> [160.926694] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [160.928446] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power on
<7> [160.928513] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [160.928605] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [160.937748] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [160.937837] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power on
<7> [160.937943] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [160.974606] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [160.975071] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [160.975407] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [160.975833] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [161.145393] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [161.146552] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on
<7> [161.147423] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [161.150510] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [161.152262] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [161.153690] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [161.155628] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [161.157456] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [161.159305] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Clock recovery OK
<7> [161.160138] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [161.162319] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [161.163157] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [161.164487] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [161.165306] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [161.165881] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [161.166543] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 13892
<7> [161.168651] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 14745600 bytes of contiguous stolen space for FBC, limit: 2
<7> [161.169045] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]
<7> [161.182428] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [161.183163] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [161.187559] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [161.216767] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [161.217480] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [161.218094] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [161.249801] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [161.250437] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [161.269185] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [161.300875] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [161.301587] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [161.302225] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [161.333132] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [161.333771] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [161.349970] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:436] from all active usage due to RMFB ioctl
<7> [161.350116] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:436] is removed
<7> [161.350294] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [161.350783] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [161.351151] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [161.351500] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [161.351876] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [161.352287] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [161.352900] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [161.353459] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [161.354038] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [161.354573] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [161.355129] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [161.365341] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]
<7> [161.399903] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436]
<7> [161.409739] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [161.410124] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [161.411536] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [161.415226] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:63:plane 2A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [161.415502] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [161.415699] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [161.415870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [161.416037] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [161.416219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [161.416444] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [161.416651] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [161.416875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [161.417068] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [161.417242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [161.418356] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [161.418556] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [161.419241] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 14745600 bytes of contiguous stolen space for FBC, limit: 2
<7> [161.419384] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:63:plane 2A]
<7> [161.433170] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [161.467792] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [161.468353] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [161.468907] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [161.501139] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [161.501672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [161.519237] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [161.549773] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [161.550304] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [161.550835] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [161.583622] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [161.584239] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [161.599834] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:436] from all active usage due to RMFB ioctl
<7> [161.599962] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:63:plane 2A] because [FB:436] is removed
<7> [161.600123] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:63:plane 2A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [161.600512] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [161.600881] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [161.601188] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [161.601483] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [161.601866] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [161.602380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [161.602896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [161.603380] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [161.603887] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [161.604363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [161.615296] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:63:plane 2A]
<7> [161.646926] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:436]
<7> [161.656725] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [161.656967] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [161.657122] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [161.659962] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:93:plane 3A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [161.660191] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [161.660333] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [161.660501] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [161.660630] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [161.660861] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [161.661103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [161.661330] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [161.661550] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [161.661793] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [161.662020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [161.663471] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [161.663795] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [161.664981] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 14745600 bytes of contiguous stolen space for FBC, limit: 2
<7> [161.665248] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:93:plane 3A]
<7> [161.683196] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [161.715780] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [161.716316] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [161.716846] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [161.749599] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [161.750151] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [161.769054] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [161.799768] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [161.800417] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [161.800980] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [161.832740] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [161.833181] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [161.849551] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:436] from all active usage due to RMFB ioctl
<7> [161.849659] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:93:plane 3A] because [FB:436] is removed
<7> [161.849851] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:93:plane 3A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [161.850167] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [161.850425] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [161.850669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [161.850941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [161.851228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [161.851643] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [161.852063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [161.852454] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [161.852860] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [161.853239] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [161.865252] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:93:plane 3A]
<6> [161.890351] [IGT] kms_frontbuffer_tracking: finished subtest plane-fbc-rte, SUCCESS
<7> [161.905077] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [161.905243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [161.905326] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [161.905401] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [161.905473] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [161.905564] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [161.905683] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [161.905963] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [161.906081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [161.906192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [161.906302] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [161.906728] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [161.906890] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [161.907012] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [161.907143] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [161.907258] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [161.908972] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 11059200 bytes of contiguous stolen space for FBC, limit: 2
<7> [161.909130] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]
<7> [161.915889] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [161.916285] [IGT] kms_frontbuffer_tracking: exiting, ret=0
<7> [161.916619] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to 0
<7> [161.917025] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [161.917188] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [161.917303] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [161.917436] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [161.917548] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [161.917773] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset]
<7> [161.917904] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [161.918012] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [161.918118] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [161.918224] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [161.918329] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [161.918434] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [161.918539] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [161.918645] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [161.918779] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [161.918887] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [161.918994] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [161.919101] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [161.919207] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [161.919312] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [161.919418] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [161.919523] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [161.919628] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [161.919743] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [161.919849] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [161.919953] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [161.920057] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [161.920160] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [161.920264] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [161.920368] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [161.920472] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [161.920577] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [161.920683] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [161.920797] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [161.920902] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [161.921007] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [161.921112] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [161.921216] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [161.921321] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [161.921425] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [161.921530] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [161.921633] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [161.921744] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [161.921851] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [161.921954] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [161.922059] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [161.922165] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [161.922268] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [161.922371] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [161.922475] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [161.922579] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [161.922683] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [161.922838] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [161.922944] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [161.923047] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [161.923150] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [161.923253] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [161.923356] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [161.923459] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [161.923562] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [161.923664] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [161.923793] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [161.923901] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [161.924003] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:392] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [161.924112] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [161.924220] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [161.931910] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]
<7> [161.948599] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [161.950403] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [161.950902] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<6> [161.965945] Console: switching to colour frame buffer device 180x56
<7> [161.982786] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [161.983350] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [161.983898] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [161.984674] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [161.985262] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [162.016757] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [162.017224] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [162.017643] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
Created at 2026-01-12 20:54:09