Results for igt@kms_plane_scaling@plane-upscale-20x20-with-modifiers@pipe-a

Result: Pass

i915_display_info23 igt_runner23 results23.json results23-xe-load.json guc_logs23.tar i915_display_info_post_exec23 boot23 dmesg23

DetailValue
Duration 0.51 seconds
Hostname 
shard-lnl-3
Igt-Version 
IGT-Version: 2.3-g15a597610 (x86_64) (Linux: 6.19.0-rc4-lgci-xe-xe-4362-8b38d6decc6810939+ x86_64)
Out 
Using IGT_SRANDOM=1768071134 for randomisation
Opened device: /dev/dri/card1
Starting subtest: plane-upscale-20x20-with-modifiers
Starting dynamic subtest: pipe-A
Trying on eDP-1
Dynamic subtest pipe-A: SUCCESS (0.509s)
Err 
Starting subtest: plane-upscale-20x20-with-modifiers
Starting dynamic subtest: pipe-A
Dynamic subtest pipe-A: SUCCESS (0.509s)
Dmesg
<6> [425.939425] Console: switching to colour dummy device 80x25
<6> [425.939677] [IGT] kms_plane_scaling: executing
<7> [425.945957] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [425.945967] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [425.946156] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [425.946272] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [425.946492] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [425.946495] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [425.946604] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [425.946685] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [425.946906] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [425.946909] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [425.947029] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [425.947129] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [425.947411] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]
<7> [425.947414] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]
<7> [425.947500] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on
<7> [425.947600] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f
<7> [425.948025] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [425.948333] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [425.948435] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [425.948535] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [425.948653] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [425.948657] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [425.948659] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [425.948660] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [425.948662] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [425.948664] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [425.948665] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor
<5> [425.948667] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [425.948668] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0
<5> [425.948670] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [425.948681] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes
<7> [425.948767] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [425.948856] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [425.949384] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [425.949386] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [425.949387] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [425.949443] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:
<7> [425.949448] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [425.949452] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [425.949465] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [425.949469] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [425.949612] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [425.949622] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [425.949625] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [425.949733] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [425.949740] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [425.949742] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [425.949845] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<6> [425.950338] [IGT] kms_plane_scaling: starting subtest plane-upscale-20x20-with-modifiers
<6> [425.950611] [IGT] kms_plane_scaling: starting dynamic subtest pipe-A
<7> [425.951783] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [425.952521] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.0: staged scaling request for 20x20->2880x1800 scaler_users = 0x1
<7> [425.952619] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [425.952688] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [425.952753] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [425.952812] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [425.952872] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:33
<7> [425.953415] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [425.953518] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [425.959600] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [425.959721] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [425.959749] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:430] is removed
<7> [425.959780] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.0: Staged freeing scaler id 0 scaler_users = 0x0
<7> [425.959859] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [425.959920] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [425.959978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [425.960074] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [425.960148] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [425.960250] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [425.960361] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [425.960461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [425.960551] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [425.960640] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [425.960726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [425.960977] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [425.994144] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [425.994430] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.0: staged scaling request for 20x20->2880x1800 scaler_users = 0x1
<7> [425.994767] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [425.995064] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [425.995295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [425.995520] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [425.995761] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [425.996061] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [425.996417] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [425.996743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [425.997085] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [425.997391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [425.997693] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [425.998105] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:33
<7> [426.009355] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.011001] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.011091] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:430] is removed
<7> [426.011146] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.0: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.011444] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.011680] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.011898] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.012132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.012314] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.012552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.012817] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.013086] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.013327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.013561] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.013787] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.014332] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.027283] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.027514] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.0: staged scaling request for 20x20->2880x1800 scaler_users = 0x1
<7> [426.027800] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.028133] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.028369] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [426.028583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [426.028785] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [426.029031] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.029375] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.029647] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.029964] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.030273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.030519] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.030823] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:33
<7> [426.042689] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.044369] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.044448] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:430] is removed
<7> [426.044500] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.0: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.044807] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.045130] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.045295] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.045448] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.045595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.045756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.045981] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.046179] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.046364] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.046547] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.046749] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.047208] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.060455] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.060734] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.1: staged scaling request for 20x20->2880x1800 scaler_users = 0x2
<7> [426.061089] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:63:plane 2A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.061367] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.061566] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.061760] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.061997] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.062202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.062558] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.1: staged scaling request for 20x20->2880x1800 scaler_users = 0x2
<7> [426.062739] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:63:plane 2A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.062896] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.063085] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.063268] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.063436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.063594] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.063814] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.064048] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.064254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.064453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.064646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.064879] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:63
<7> [426.076031] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.077520] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.077566] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:63:plane 2A] because [FB:430] is removed
<7> [426.077598] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.1: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.077765] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:63:plane 2A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.077914] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.078212] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.078436] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.078701] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.078948] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.079202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.079378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.079538] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.079690] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.079840] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.080233] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.093520] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.093689] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.1: staged scaling request for 20x20->2880x1800 scaler_users = 0x2
<7> [426.093925] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:63:plane 2A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.094173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.094356] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.094528] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.094712] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.094897] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.095149] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.095370] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.095586] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.095834] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.096070] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.096308] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:63
<7> [426.109322] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.110823] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.110883] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:63:plane 2A] because [FB:430] is removed
<7> [426.110921] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.1: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.111329] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:63:plane 2A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.111625] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.111855] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.112075] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.112239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.112421] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.112652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.112875] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.113117] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.113320] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.113555] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.114092] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.127148] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.127360] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.1: staged scaling request for 20x20->2880x1800 scaler_users = 0x2
<7> [426.127687] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:63:plane 2A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.128053] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.128303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [426.128544] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [426.128795] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [426.129093] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.129414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.129725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.130035] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.130308] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.130565] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.130921] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:63
<7> [426.142647] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.144110] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.144171] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:63:plane 2A] because [FB:430] is removed
<7> [426.144207] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.1: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.144448] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:63:plane 2A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.144697] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.144907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.145237] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.145438] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:63:plane 2A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.145652] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.145950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.146219] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.146466] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.146758] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.147020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.147528] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.160426] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.160675] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.2: staged scaling request for 20x20->2880x1800 scaler_users = 0x4
<7> [426.161016] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:93:plane 3A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.161298] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.161533] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.161762] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.162065] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.162298] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.162582] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.162848] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.163138] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.163429] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.163668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.163967] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:93
<7> [426.175983] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.177543] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.177612] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:93:plane 3A] because [FB:430] is removed
<7> [426.177658] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.2: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.177917] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:93:plane 3A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.178216] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.178439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.178657] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.178914] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.179193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.179461] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.179714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.179983] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.180221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.180450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.180977] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.193563] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.193762] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.2: staged scaling request for 20x20->2880x1800 scaler_users = 0x4
<7> [426.194122] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:93:plane 3A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.194404] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.194613] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.194817] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.195041] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.195253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.195518] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.195762] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.196030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.196254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.196473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.196736] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:93
<7> [426.209296] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.210752] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.210814] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:93:plane 3A] because [FB:430] is removed
<7> [426.210848] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.2: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.211196] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:93:plane 3A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.211430] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.211649] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.211867] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.212159] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.212352] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.212644] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.212878] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.213127] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.213340] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.213539] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.214661] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.227480] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.227718] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.2: staged scaling request for 20x20->2880x1800 scaler_users = 0x4
<7> [426.228668] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:93:plane 3A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.228954] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.229183] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [426.229391] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [426.229638] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [426.229880] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.230228] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.230501] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.230767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.231043] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.231325] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.231600] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:93
<7> [426.242648] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.244318] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.244401] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:93:plane 3A] because [FB:430] is removed
<7> [426.244453] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.2: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.244755] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:93:plane 3A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.245046] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.245243] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.245446] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.245640] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:93:plane 3A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.245836] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.246123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.246363] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.246597] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.246829] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.247115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.247700] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.260257] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.260488] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.3: staged scaling request for 20x20->2880x1800 scaler_users = 0x8
<7> [426.260772] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.261044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.261256] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.261462] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.261705] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.261950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.262213] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.262471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.262713] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.262966] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.263192] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.263456] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:123
<7> [426.275958] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.277505] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.277576] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:123:plane 4A] because [FB:430] is removed
<7> [426.277625] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.3: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.277872] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.278139] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.278327] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.278508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.278698] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.278909] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.279155] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.279391] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.279617] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.279833] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.280094] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.280546] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.293676] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.293967] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.3: staged scaling request for 20x20->2880x1800 scaler_users = 0x8
<7> [426.294249] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.294465] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.294669] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.294864] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.295143] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.295366] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.295675] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.295950] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.296253] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.296515] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.296770] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.297096] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:123
<7> [426.309294] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.310995] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.311091] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:123:plane 4A] because [FB:430] is removed
<7> [426.311146] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.3: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.311447] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.311742] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.311994] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.312174] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.312343] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.312526] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.312769] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.313020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.313237] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.313450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.313658] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.314177] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.326930] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.327110] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.3: staged scaling request for 20x20->2880x1800 scaler_users = 0x8
<7> [426.327381] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.327596] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.327801] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [426.328049] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [426.328244] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [426.328511] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.328896] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.3: staged scaling request for 20x20->2880x1800 scaler_users = 0x8
<7> [426.329112] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.329284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.329449] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [426.329632] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [426.329813] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [426.330030] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.330254] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.330473] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.330686] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.330949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.331150] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.331857] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:123
<7> [426.342632] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.343976] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.344019] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:123:plane 4A] because [FB:430] is removed
<7> [426.344047] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.3: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.344343] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:123:plane 4A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.344583] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.344810] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.345132] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.345260] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:123:plane 4A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.345451] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.345646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.345819] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.346004] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.346167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.346327] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.346714] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.360007] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.360211] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.4: staged scaling request for 20x20->2880x1800 scaler_users = 0x10
<7> [426.360412] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.360573] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.360734] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.360923] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.361090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.361299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.361588] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.4: staged scaling request for 20x20->2880x1800 scaler_users = 0x10
<7> [426.361744] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.361897] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.362029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.362173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.362297] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.362428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.362678] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.4: staged scaling request for 20x20->2880x1800 scaler_users = 0x10
<7> [426.362812] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.362985] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.363119] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.363239] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.363371] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.363513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.363689] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.363872] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.364040] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.364202] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.364360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.364548] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:133
<7> [426.376000] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.377366] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.377407] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:133:plane 5A] because [FB:430] is removed
<7> [426.377431] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.4: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.377581] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.377723] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.377870] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.377978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.378089] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.378218] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.378373] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.378520] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.378659] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.378797] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.378961] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.379259] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.393230] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.393365] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.4: staged scaling request for 20x20->2880x1800 scaler_users = 0x10
<7> [426.393539] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.393708] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.393884] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0
<7> [426.394023] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33
<7> [426.394173] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34
<7> [426.394326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.394525] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.394711] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.394903] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.395081] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.395252] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.395455] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:133
<7> [426.409268] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.410703] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.410761] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:133:plane 5A] because [FB:430] is removed
<7> [426.410794] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.4: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.411048] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.411262] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.411468] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 9, 13, 13, 13, 13, 13, 0, 0, 0, 9, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.411679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 19, 27, 27, 27, 27, 27, 0, 0, 33, 19, 33 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.411924] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 22, 31, 31, 31, 31, 31, 0, 0, 34, 22, 34 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.412111] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.412368] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.412607] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.412896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.413115] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.413336] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.413873] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [426.426877] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [426.427058] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.4: staged scaling request for 20x20->2880x1800 scaler_users = 0x10
<7> [426.427296] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [426.427487] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [426.427679] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0
<7> [426.427907] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19
<7> [426.428102] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20
<7> [426.428318] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [426.428593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [426.428870] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [426.429126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.429382] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [426.429619] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [426.429929] xe 0000:00:02.0: [drm:intel_atomic_setup_scaler [xe]] [CRTC:149:pipe A] attached scaler id 0.0 to PLANE:133
<7> [426.442602] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [426.444308] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [426.444384] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:133:plane 5A] because [FB:430] is removed
<7> [426.444428] xe 0000:00:02.0: [drm:skl_update_scaler [xe]] [CRTC:149:pipe A] scaler_user index 0.4: Staged freeing scaler id 0 scaler_users = 0x0
<7> [426.444714] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:133:plane 5A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [426.444978] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [426.445162] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] lines 4, 13, 13, 13, 13, 13, 0, 0, 0, 4, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.445344] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] blocks 3, 8, 8, 8, 8, 8, 0, 0, 19, 3, 19 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.445551] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:133:plane 5A] min_ddb 5, 11, 11, 11, 11, 11, 0, 0, 20, 5, 20 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [426.445752] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [426.446054] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [426.446303] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [426.446598] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.446831] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [426.447110] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [426.447609] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<6> [426.460916] [IGT] kms_plane_scaling: finished subtest pipe-A, SUCCESS
Created at 2026-01-10 19:00:49