Result:
igt_runner0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0
| Detail | Value |
|---|---|
| Duration | 5.50 seconds |
| Igt-Version |
IGT-Version: 2.3-g9eddcf2b9 (x86_64) (Linux: 6.19.0-rc4-lgci-xe-xe-4352-70c59cc4737250313+ x86_64) |
| Out |
Starting dynamic subtest: pipe-B-eDP-1 Dynamic subtest pipe-B-eDP-1: SUCCESS (5.499s) |
| Err |
Starting dynamic subtest: pipe-B-eDP-1 Dynamic subtest pipe-B-eDP-1: SUCCESS (5.499s) |
| Dmesg |
<6> [283.236896] [IGT] kms_pipe_crc_basic: starting dynamic subtest pipe-B-eDP-1
<7> [283.239456] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:556]
<7> [283.244615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [283.245112] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [283.245557] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [283.245939] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [283.283501] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:558]
<7> [283.323478] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [283.323890] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [283.324589] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [283.326197] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [283.332563] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [283.332634] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:510:eDP-1]
<7> [283.332840] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:510:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [283.333238] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:509:DDI A/PHY A][CRTC:268:pipe B] DP link limits: pixel clock 317250 kHz DSC off max lanes 4 max rate 270000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000
<7> [283.333571] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 243000 bpp input 24 compressed 0.0000 link rate required 951750 available 972000
<7> [283.333869] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [283.334157] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:509:DDI A/PHY A] [CRTC:268:pipe B]
<7> [283.334451] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.enable (expected no, found yes)
<7> [283.334940] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.active (expected no, found yes)
<7> [283.335217] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in cpu_transcoder (expected -1, found 1)
<7> [283.335544] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in lane_count (expected 0, found 4)
<7> [283.335819] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 8213845/8388608 link 684487/524288)
<7> [283.336091] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [283.336360] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [283.336675] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 1920)
<7> [283.336943] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 2080)
<7> [283.337207] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 1920)
<7> [283.337538] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 2080)
<7> [283.337801] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 1968)
<7> [283.338063] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2000)
<7> [283.338323] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1200)
<7> [283.338606] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1203)
<7> [283.338868] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1209)
<7> [283.339128] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1271)
<7> [283.339389] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1271)
<7> [283.339698] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 1920)
<7> [283.339961] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 2080)
<7> [283.340222] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 1920)
<7> [283.340525] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 2080)
<7> [283.340785] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 1968)
<7> [283.341045] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2000)
<7> [283.341303] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1200)
<7> [283.341592] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1203)
<7> [283.341854] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1209)
<7> [283.342116] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1271)
<7> [283.342376] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1271)
<7> [283.342666] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [283.342928] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [283.343188] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [283.343449] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in enhanced_framing (expected no, found yes)
<7> [283.343745] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [283.344006] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 317250)
<7> [283.344265] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 317250)
<7> [283.344562] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in port_clock (expected 0, found 243000)
<7> [283.344826] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in vrr.guardband (expected 0, found 69)
<7> [283.345087] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] fastset requirement not met, forcing full modeset
<7> [283.345673] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [283.345946] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:268:pipe B] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x2
<7> [283.346240] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:152:plane 1B] ddb ( 0 - 0) -> ( 0 - 4032), size 0 -> 4032
<7> [283.346435] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:262:cursor B] ddb ( 0 - 0) -> (4032 - 4096), size 0 -> 64
<7> [283.346650] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:152:plane 1B] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [283.346837] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:152:plane 1B] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 16, 17, 19, 19, 19, 0, 0, 0, 3, 0
<7> [283.347020] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:152:plane 1B] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 256, 272, 304, 304, 304, 0, 0, 30, 48, 62
<7> [283.347199] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:152:plane 1B] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 283, 301, 336, 336, 336, 0, 0, 31, 54, 63
<7> [283.347428] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:268:pipe B] data rate 1269000 num active planes 1
<7> [283.347767] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1333 qgv_peak_bw: 38400
<7> [283.348063] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1333 qgv_peak_bw: 38400
<7> [283.348347] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 42130 required 1333 qgv_peak_bw: 38400
<7> [283.348646] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 45877 required 1333 qgv_peak_bw: 38400
<7> [283.348927] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1333
<7> [283.349207] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:268:pipe B] min cdclk: 0 kHz -> 158625 kHz
<7> [283.349556] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 19829 kHz
<7> [283.349843] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [283.350121] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz
<7> [283.350397] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [283.350743] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:268:pipe B] allocated DPLL 0
<7> [283.351003] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:268:pipe B] reserving DPLL 0
<7> [283.351262] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:268:pipe B] enable: yes [modeset]
<7> [283.351516] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [283.351561] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [283.351845] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: B, pipe bpp: 24, dithering: 0
<7> [283.351883] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [283.352126] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [283.352191] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [283.352405] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [283.352508] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [283.352698] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [283.352978] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [283.353256] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8213845, data_n: 8388608, link_m: 684487, link_n: 524288, tu: 64
<7> [283.353548] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [283.353826] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: enabled
<7> [283.354102] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [283.354376] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [283.354686] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [283.354965] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [283.355241] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [283.355533] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [283.355809] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [283.356084] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [283.356356] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [283.356644] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [283.356918] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [283.357191] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [283.357480] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1271, vmax: 1271, flipline: 1271, pipeline full: 0, guardband: 69 vsync start: 68, vsync end: 62
<7> [283.357757] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1202, vmax vblank: 1202, vmin vtotal: 1271, vmax vtotal: 1271
<7> [283.358031] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [283.358308] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x48 0xa
<7> [283.358604] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x48 0xa
<7> [283.358882] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=317250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1200 vb=1202-1271 vs=1203-1209 vt=1271, flags=0xa
<7> [283.359158] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x40 0xa
<7> [283.359432] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=317250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1200 vb=1202-1271 vs=1203-1209 vt=1271, flags=0xa
<7> [283.359724] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 243000, pipe src: 1920x1200+0+0, pixel rate 317250, min cdclk 158625
<7> [283.360003] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 53, ips linetime: 0
<7> [283.360276] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [283.360567] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [283.360840] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [283.361112] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [283.361384] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 243000, fracen: yes,
<7> [283.361672] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] quot: 8192, rem: 0, den: 1,
<7> [283.361948] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 253, tx_clk_div: 2.
<7> [283.362223] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [283.362521] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [283.362794] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x34, pll[1] = 0x0, pll[2] = 0xda, pll[3] = 0x1
<7> [283.363069] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [283.363340] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [283.363629] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x20, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x2
<7> [283.363908] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0x8f, pll[18] = 0xe6, pll[19] = 0x23
<7> [283.364184] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [283.364476] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [283.364751] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [283.365025] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [283.365297] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [283.365587] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [283.365863] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [283.366135] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [283.366409] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [283.366693] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [283.366968] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [283.367239] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [283.367528] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [283.367802] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:152:plane 1B] fb: [FB:556] 1920x1200 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [283.368078] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [283.368350] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 1920.000000x1200.000000+0.000000+0.000000 dst: 1920x1200+0+0
<7> [283.368643] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:182:plane 2B] fb: [NOFB], visible: no
<7> [283.368918] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:212:plane 3B] fb: [NOFB], visible: no
<7> [283.369190] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:242:plane 4B] fb: [NOFB], visible: no
<7> [283.369477] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:252:plane 5B] fb: [NOFB], visible: no
<7> [283.369751] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:262:cursor B] fb: [NOFB], visible: no
<7> [283.370968] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [283.371250] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [283.371548] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [283.371917] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_B
<7> [283.372263] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 172800 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [283.372602] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [283.372839] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=432
<7> [283.373124] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:509:DDI A/PHY A]
<7> [283.373353] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:518:DDI TC1/PHY TC1]
<7> [283.373588] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:520:DP-MST A]
<7> [283.373804] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:521:DP-MST B]
<7> [283.374015] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:522:DP-MST C]
<7> [283.374224] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:523:DP-MST D]
<7> [283.374429] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:531:DDI TC2/PHY TC2]
<7> [283.374651] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:533:DP-MST A]
<7> [283.374859] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:534:DP-MST B]
<7> [283.375062] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:535:DP-MST C]
<7> [283.375265] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:536:DP-MST D]
<7> [283.375485] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:540:DDI TC3/PHY TC3]
<7> [283.375689] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:542:DP-MST A]
<7> [283.375892] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:543:DP-MST B]
<7> [283.376095] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:544:DP-MST C]
<7> [283.376298] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:545:DP-MST D]
<7> [283.376518] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:549:DDI TC4/PHY TC4]
<7> [283.376754] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [283.377101] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [283.377303] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [283.377565] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [283.378485] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x2, on? 0) for [CRTC:268:pipe B]
<7> [283.378735] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [283.380213] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turn panel power on
<7> [283.380437] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power cycle (333 ms remaining)
<7> [283.719764] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [283.777869] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [283.778404] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power on
<7> [283.778976] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [283.803769] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [283.804381] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:509:DDI A/PHY A] - long
<7> [283.804856] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [283.805423] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:509:DDI A/PHY A]
<7> [283.985802] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [283.986322] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turning VDD on
<7> [283.986835] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [283.989168] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 0a c4 41 00 10 01 c0 02 00 00 00 1f 0b 80
<7> [283.990094] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [283.990962] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 02
<7> [283.992272] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [283.993152] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [283.994379] xe 0000:00:02.0: [drm:intel_dp_get_adjust_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0
<7> [283.994761] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0
<7> [283.996537] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Clock recovery OK
<7> [283.996898] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [283.998636] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [283.999179] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Link Training passed at link rate = 243000, lane count = 4
<7> [284.000233] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe B
<7> [284.000844] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [284.001265] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe B
<7> [284.001745] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:510:eDP-1] set backlight PWM = 13892
<7> [284.009569] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [284.011584] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:510:eDP-1]
<7> [284.012020] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:268:pipe B]
<7> [284.022769] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [284.030041] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:506:pipe D]
<7> [284.054125] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe B
<7> [284.054971] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe B
<7> [284.055638] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:510:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [284.056085] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:509:DDI A/PHY A][CRTC:268:pipe B] DP link limits: pixel clock 317250 kHz DSC off max lanes 4 max rate 270000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000
<7> [284.056469] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 243000 bpp input 24 compressed 0.0000 link rate required 951750 available 972000
<7> [284.056819] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation
<7> [284.057131] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [284.057512] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:509:DDI A/PHY A] [CRTC:268:pipe B]
<7> [284.057860] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [284.058191] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] fastset requirement not met, forcing full modeset
<7> [284.058654] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:268:pipe B] releasing DPLL 0
<7> [284.059102] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:268:pipe B] allocated DPLL 0
<7> [284.059392] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:268:pipe B] reserving DPLL 0
<7> [284.059704] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:268:pipe B] enable: yes [modeset]
<7> [284.060053] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [284.060392] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: B, pipe bpp: 24, dithering: 0
<7> [284.060742] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [284.061075] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [284.061409] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [284.061750] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [284.062084] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8213845, data_n: 8388608, link_m: 684487, link_n: 524288, tu: 64
<7> [284.062427] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [284.062759] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: enabled
<7> [284.063088] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [284.063504] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [284.063832] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [284.064160] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [284.064501] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8
<7> [284.064801] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [284.065101] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [284.065398] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [284.065708] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [284.066010] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [284.066311] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [284.066620] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [284.066922] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1271, vmax: 1271, flipline: 1271, pipeline full: 0, guardband: 69 vsync start: 68, vsync end: 62
<7> [284.067222] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1202, vmax vblank: 1202, vmin vtotal: 1271, vmax vtotal: 1271
<7> [284.067533] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [284.067836] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x48 0xa
<7> [284.068140] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x48 0xa
<7> [284.068451] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=317250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1200 vb=1202-1271 vs=1203-1209 vt=1271, flags=0xa
<7> [284.068754] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x40 0xa
<7> [284.069056] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=317250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1200 vb=1202-1271 vs=1203-1209 vt=1271, flags=0xa
<7> [284.069359] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 243000, pipe src: 1920x1200+0+0, pixel rate 317250, min cdclk 158625
<7> [284.069672] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 53, ips linetime: 0
<7> [284.069972] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [284.070271] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [284.070698] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [284.070976] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [284.071255] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 243000, fracen: yes,
<7> [284.071584] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] quot: 8192, rem: 0, den: 1,
<7> [284.071610] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [284.071865] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 253, tx_clk_div: 2.
<7> [284.071975] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [284.072140] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [284.072276] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [284.072447] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [284.072724] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x34, pll[1] = 0x0, pll[2] = 0xda, pll[3] = 0x1
<7> [284.073002] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [284.073278] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [284.073572] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x20, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x2
<7> [284.073853] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0x8f, pll[18] = 0xe6, pll[19] = 0x23
<7> [284.074133] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [284.074425] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [284.074702] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [284.074978] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [284.075252] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [284.075538] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [284.075819] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [284.076097] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [284.076374] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [284.076662] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [284.076940] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [284.077213] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [284.077503] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [284.077780] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:152:plane 1B] fb: [FB:556] 1920x1200 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [284.078056] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [284.078330] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 1920.000000x1200.000000+0.000000+0.000000 dst: 1920x1200+0+0
<7> [284.078627] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:182:plane 2B] fb: [NOFB], visible: no
<7> [284.078904] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:212:plane 3B] fb: [NOFB], visible: no
<7> [284.079178] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:242:plane 4B] fb: [NOFB], visible: no
<7> [284.079467] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:252:plane 5B] fb: [NOFB], visible: no
<7> [284.079745] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:262:cursor B] fb: [NOFB], visible: no
<7> [284.080311] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [284.080836] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [284.081354] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [284.085253] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [284.085714] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [284.287708] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:510:eDP-1] set backlight PWM = 0
<7> [284.288222] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe B
<7> [284.294057] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turn panel power off
<7> [284.294683] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [284.295194] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [284.346468] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [284.346857] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x2, on? 1) for [CRTC:268:pipe B]
<7> [284.347262] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [284.347680] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:509:DDI A/PHY A] - long
<7> [284.347846] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [284.348068] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [284.348297] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [284.348526] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:509:DDI A/PHY A]
<7> [284.348843] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:509:DDI A/PHY A]
<7> [284.349224] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:518:DDI TC1/PHY TC1]
<7> [284.349606] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:520:DP-MST A]
<7> [284.349941] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:521:DP-MST B]
<7> [284.350260] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:522:DP-MST C]
<7> [284.350613] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:523:DP-MST D]
<7> [284.350924] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:531:DDI TC2/PHY TC2]
<7> [284.351232] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:533:DP-MST A]
<7> [284.351575] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:534:DP-MST B]
<7> [284.351877] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:535:DP-MST C]
<7> [284.352179] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:536:DP-MST D]
<7> [284.352565] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:540:DDI TC3/PHY TC3]
<7> [284.352869] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:542:DP-MST A]
<7> [284.353167] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:543:DP-MST B]
<7> [284.353479] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:544:DP-MST C]
<7> [284.353778] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:545:DP-MST D]
<7> [284.354074] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:549:DDI TC4/PHY TC4]
<7> [284.354479] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [284.356236] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x2, on? 0) for [CRTC:268:pipe B]
<7> [284.356734] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [284.358389] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turn panel power on
<7> [284.358769] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power cycle (489 ms remaining)
<7> [284.855790] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [284.886551] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [284.887012] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power on
<7> [284.887459] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [284.912433] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [284.912894] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:509:DDI A/PHY A] - long
<7> [284.913279] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [284.913798] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:509:DDI A/PHY A]
<7> [285.092007] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [285.092451] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turning VDD on
<7> [285.092802] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [285.095038] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 0a c4 41 00 10 01 c0 02 00 00 00 1f 0b 80
<7> [285.095943] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [285.096814] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 02
<7> [285.098085] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [285.098974] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [285.100159] xe 0000:00:02.0: [drm:intel_dp_get_adjust_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0
<7> [285.100565] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0
<7> [285.102343] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Clock recovery OK
<7> [285.102795] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [285.104463] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [285.104947] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Link Training passed at link rate = 243000, lane count = 4
<7> [285.105945] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe B
<7> [285.106463] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [285.106909] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe B
<7> [285.107404] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:510:eDP-1] set backlight PWM = 13892
<7> [285.108776] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 9830400 bytes of contiguous stolen space for FBC, limit: 1
<7> [285.109164] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:152:plane 1B]
<7> [285.115121] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [285.116820] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:510:eDP-1]
<7> [285.117276] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:268:pipe B]
<7> [285.136553] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [285.137035] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [285.137467] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [285.140439] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:510:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [285.140907] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:509:DDI A/PHY A][CRTC:268:pipe B] DP link limits: pixel clock 317250 kHz DSC off max lanes 4 max rate 270000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000
<7> [285.141302] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 243000 bpp input 24 compressed 0.0000 link rate required 951750 available 972000
<7> [285.141793] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [285.142177] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:509:DDI A/PHY A] [CRTC:268:pipe B]
<7> [285.142593] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [285.142956] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] fastset requirement not met, forcing full modeset
<7> [285.143305] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:268:pipe B] releasing DPLL 0
<7> [285.143878] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:268:pipe B] allocated DPLL 0
<7> [285.144222] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:268:pipe B] reserving DPLL 0
<7> [285.144594] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:268:pipe B] enable: yes [modeset]
<7> [285.144997] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [285.145346] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: B, pipe bpp: 24, dithering: 0
<7> [285.145736] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [285.146132] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [285.146552] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [285.146924] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [285.147256] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8213845, data_n: 8388608, link_m: 684487, link_n: 524288, tu: 64
<7> [285.147621] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [285.147953] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: enabled
<7> [285.148284] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [285.148695] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [285.149027] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [285.149367] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [285.149738] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [285.150066] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [285.150404] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [285.150741] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [285.151068] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [285.151443] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [285.151774] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [285.152099] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [285.152432] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1271, vmax: 1271, flipline: 1271, pipeline full: 0, guardband: 69 vsync start: 68, vsync end: 62
<7> [285.152763] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1202, vmax vblank: 1202, vmin vtotal: 1271, vmax vtotal: 1271
<7> [285.153091] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [285.153427] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x48 0xa
<7> [285.153795] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x48 0xa
<7> [285.154126] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=317250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1200 vb=1202-1271 vs=1203-1209 vt=1271, flags=0xa
<7> [285.154468] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x40 0xa
<7> [285.154798] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=317250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1200 vb=1202-1271 vs=1203-1209 vt=1271, flags=0xa
<7> [285.155130] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 243000, pipe src: 1920x1200+0+0, pixel rate 317250, min cdclk 158625
<7> [285.155511] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 53, ips linetime: 0
<7> [285.155839] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [285.156154] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [285.156484] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [285.156793] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [285.157100] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 243000, fracen: yes,
<7> [285.157412] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] quot: 8192, rem: 0, den: 1,
<7> [285.157714] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 253, tx_clk_div: 2.
<7> [285.158051] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [285.158386] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [285.158687] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x34, pll[1] = 0x0, pll[2] = 0xda, pll[3] = 0x1
<7> [285.158988] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [285.159286] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [285.159622] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x20, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x2
<7> [285.159921] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0x8f, pll[18] = 0xe6, pll[19] = 0x23
<7> [285.160219] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [285.160546] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [285.160882] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [285.161226] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [285.161557] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [285.161855] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [285.162153] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [285.162464] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [285.162838] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [285.163147] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [285.163451] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [285.163742] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [285.164032] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [285.164323] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:152:plane 1B] fb: [FB:556] 1920x1200 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [285.164665] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [285.165000] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 1920.000000x1200.000000+0.000000+0.000000 dst: 1920x1200+0+0
<7> [285.165294] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:182:plane 2B] fb: [NOFB], visible: no
<7> [285.165621] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:212:plane 3B] fb: [NOFB], visible: no
<7> [285.165910] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:242:plane 4B] fb: [NOFB], visible: no
<7> [285.166200] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:252:plane 5B] fb: [NOFB], visible: no
<7> [285.166524] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:262:cursor B] fb: [NOFB], visible: no
<7> [285.166919] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [285.167344] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [285.167853] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [285.173528] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [285.173978] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [285.375634] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:510:eDP-1] set backlight PWM = 0
<7> [285.376234] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe B
<7> [285.382122] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turn panel power off
<7> [285.382889] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [285.383441] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [285.435557] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [285.435963] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:509:DDI A/PHY A] - long
<7> [285.436281] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [285.436686] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:509:DDI A/PHY A]
<7> [285.441725] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [285.442271] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x2, on? 1) for [CRTC:268:pipe B]
<7> [285.443444] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [285.443982] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [285.444559] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:152:plane 1B]
<7> [285.445300] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:509:DDI A/PHY A]
<7> [285.445776] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:518:DDI TC1/PHY TC1]
<7> [285.446230] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:520:DP-MST A]
<7> [285.446635] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:521:DP-MST B]
<7> [285.446974] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:522:DP-MST C]
<7> [285.447308] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:523:DP-MST D]
<7> [285.447687] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:531:DDI TC2/PHY TC2]
<7> [285.448032] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:533:DP-MST A]
<7> [285.448368] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:534:DP-MST B]
<7> [285.448693] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:535:DP-MST C]
<7> [285.449017] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:536:DP-MST D]
<7> [285.449412] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:540:DDI TC3/PHY TC3]
<7> [285.449752] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:542:DP-MST A]
<7> [285.450072] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:543:DP-MST B]
<7> [285.450402] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:544:DP-MST C]
<7> [285.450723] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:545:DP-MST D]
<7> [285.451043] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:549:DDI TC4/PHY TC4]
<7> [285.451464] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [285.453250] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x2, on? 0) for [CRTC:268:pipe B]
<7> [285.453791] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [285.455501] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turn panel power on
<7> [285.455896] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power cycle (487 ms remaining)
<7> [285.951631] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [285.992673] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [285.993058] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power on
<7> [285.993411] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [286.018434] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [286.018855] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:509:DDI A/PHY A] - long
<7> [286.019222] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [286.019750] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:509:DDI A/PHY A]
<7> [286.197623] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [286.198050] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turning VDD on
<7> [286.198420] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [286.200669] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 0a c4 41 00 10 01 c0 02 00 00 00 1f 0b 80
<7> [286.201578] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [286.202467] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 02
<7> [286.203726] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [286.204620] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [286.205832] xe 0000:00:02.0: [drm:intel_dp_get_adjust_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0
<7> [286.206199] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0
<7> [286.207933] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Clock recovery OK
<7> [286.208317] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [286.209813] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [286.210170] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Link Training passed at link rate = 243000, lane count = 4
<7> [286.211100] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe B
<7> [286.211627] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [286.212056] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe B
<7> [286.212504] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:510:eDP-1] set backlight PWM = 13892
<7> [286.220326] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [286.222169] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:510:eDP-1]
<7> [286.222669] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:268:pipe B]
<7> [286.225044] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [286.225152] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:510:eDP-1]
<7> [286.230299] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe B
<7> [286.230968] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:510:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [286.231460] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:509:DDI A/PHY A][CRTC:268:pipe B] DP link limits: pixel clock 317250 kHz DSC off max lanes 4 max rate 270000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000
<7> [286.231945] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 243000 bpp input 24 compressed 0.0000 link rate required 951750 available 972000
<7> [286.232335] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation
<7> [286.232658] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [286.233021] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:509:DDI A/PHY A] [CRTC:268:pipe B]
<7> [286.233396] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [286.233745] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] fastset requirement not met, forcing full modeset
<7> [286.234084] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:268:pipe B] releasing DPLL 0
<7> [286.234702] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:510:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [286.235065] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:509:DDI A/PHY A][CRTC:268:pipe B] DP link limits: pixel clock 317250 kHz DSC off max lanes 4 max rate 270000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000
<7> [286.235472] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 243000 bpp input 24 compressed 0.0000 link rate required 951750 available 972000
<7> [286.235808] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] Selective update not enabled because it would inhibit pipe CRC calculation
<7> [286.236108] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [286.236480] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:509:DDI A/PHY A] [CRTC:268:pipe B]
<7> [286.236822] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [286.237188] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] fastset requirement not met, forcing full modeset
<7> [286.237547] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:268:pipe B] releasing DPLL 0
<7> [286.237980] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:268:pipe B] allocated DPLL 0
<7> [286.238313] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:268:pipe B] reserving DPLL 0
<7> [286.238643] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:268:pipe B] enable: yes [modeset]
<7> [286.238990] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [286.239426] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: B, pipe bpp: 24, dithering: 0
<7> [286.239766] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [286.240103] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [286.240463] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [286.240841] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [286.241216] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8213845, data_n: 8388608, link_m: 684487, link_n: 524288, tu: 64
<7> [286.241581] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [286.241893] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: enabled
<7> [286.242243] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [286.242598] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [286.242907] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [286.243212] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [286.243553] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 2, length 8
<7> [286.243856] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [286.244156] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [286.244489] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [286.244783] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [286.245077] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [286.245377] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [286.245722] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [286.246034] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1271, vmax: 1271, flipline: 1271, pipeline full: 0, guardband: 69 vsync start: 68, vsync end: 62
<7> [286.246348] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1202, vmax vblank: 1202, vmin vtotal: 1271, vmax vtotal: 1271
<7> [286.246427] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [286.246639] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [286.246932] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x48 0xa
<7> [286.246944] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [286.247226] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x48 0xa
<7> [286.247373] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [286.247652] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=317250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1200 vb=1202-1271 vs=1203-1209 vt=1271, flags=0xa
<7> [286.247970] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x40 0xa
<7> [286.248261] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=317250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1200 vb=1202-1271 vs=1203-1209 vt=1271, flags=0xa
<7> [286.248606] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 243000, pipe src: 1920x1200+0+0, pixel rate 317250, min cdclk 158625
<7> [286.248897] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 53, ips linetime: 0
<7> [286.249185] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [286.249511] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [286.249849] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [286.250137] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [286.250460] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 243000, fracen: yes,
<7> [286.250749] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] quot: 8192, rem: 0, den: 1,
<7> [286.251036] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 253, tx_clk_div: 2.
<7> [286.251337] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [286.251623] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [286.251906] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x34, pll[1] = 0x0, pll[2] = 0xda, pll[3] = 0x1
<7> [286.252193] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [286.252515] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [286.252851] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x20, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x2
<7> [286.253137] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0x8f, pll[18] = 0xe6, pll[19] = 0x23
<7> [286.253458] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [286.253744] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [286.254030] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [286.254325] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [286.254610] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [286.254892] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [286.255176] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [286.255502] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [286.255788] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [286.256136] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [286.256484] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [286.256773] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [286.257062] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [286.257361] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:152:plane 1B] fb: [FB:558] 1920x1200 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [286.257657] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [286.257944] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 1920.000000x1200.000000+0.000000+0.000000 dst: 1920x1200+0+0
<7> [286.258234] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:182:plane 2B] fb: [NOFB], visible: no
<7> [286.258565] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:212:plane 3B] fb: [NOFB], visible: no
<7> [286.258853] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:242:plane 4B] fb: [NOFB], visible: no
<7> [286.259198] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:252:plane 5B] fb: [NOFB], visible: no
<7> [286.259552] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:262:cursor B] fb: [NOFB], visible: no
<7> [286.259920] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [286.260275] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [286.260797] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [286.261761] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [286.262109] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [286.471506] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:510:eDP-1] set backlight PWM = 0
<7> [286.472059] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe B
<7> [286.482848] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turn panel power off
<7> [286.483393] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [286.483845] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [286.536044] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [286.536421] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:509:DDI A/PHY A] - long
<7> [286.536732] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [286.537153] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:509:DDI A/PHY A]
<7> [286.539438] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [286.539858] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x2, on? 1) for [CRTC:268:pipe B]
<7> [286.540865] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [286.541310] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [286.541781] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:509:DDI A/PHY A]
<7> [286.542109] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:518:DDI TC1/PHY TC1]
<7> [286.542447] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:520:DP-MST A]
<7> [286.542742] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:521:DP-MST B]
<7> [286.543028] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:522:DP-MST C]
<7> [286.543325] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:523:DP-MST D]
<7> [286.543606] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:531:DDI TC2/PHY TC2]
<7> [286.543883] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:533:DP-MST A]
<7> [286.544159] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:534:DP-MST B]
<7> [286.544469] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:535:DP-MST C]
<7> [286.544797] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:536:DP-MST D]
<7> [286.545101] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:540:DDI TC3/PHY TC3]
<7> [286.545394] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:542:DP-MST A]
<7> [286.545665] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:543:DP-MST B]
<7> [286.545934] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:544:DP-MST C]
<7> [286.546201] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:545:DP-MST D]
<7> [286.546504] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:549:DDI TC4/PHY TC4]
<7> [286.546903] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [286.548418] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x2, on? 0) for [CRTC:268:pipe B]
<7> [286.548854] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [286.550515] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turn panel power on
<7> [286.550856] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power cycle (489 ms remaining)
<7> [287.047589] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [287.098982] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [287.099793] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power on
<7> [287.100472] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [287.125144] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [287.125671] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:509:DDI A/PHY A] - long
<7> [287.126145] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [287.126709] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:509:DDI A/PHY A]
<7> [287.301123] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [287.301589] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turning VDD on
<7> [287.301930] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [287.304134] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 0a c4 41 00 10 01 c0 02 00 00 00 1f 0b 80
<7> [287.305044] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [287.305934] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 02
<7> [287.307155] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [287.308065] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [287.309275] xe 0000:00:02.0: [drm:intel_dp_get_adjust_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0
<7> [287.309678] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0
<7> [287.311399] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Clock recovery OK
<7> [287.311755] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [287.313457] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [287.313950] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Link Training passed at link rate = 243000, lane count = 4
<7> [287.314951] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe B
<7> [287.315483] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [287.315877] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe B
<7> [287.316321] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:510:eDP-1] set backlight PWM = 13892
<7> [287.317747] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 9830400 bytes of contiguous stolen space for FBC, limit: 1
<7> [287.318186] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:152:plane 1B]
<7> [287.324072] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR1
<7> [287.325661] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:510:eDP-1]
<7> [287.326125] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:268:pipe B]
<7> [287.345460] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [287.345942] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [287.346374] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [287.349436] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:510:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [287.349904] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:509:DDI A/PHY A][CRTC:268:pipe B] DP link limits: pixel clock 317250 kHz DSC off max lanes 4 max rate 270000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000
<7> [287.350327] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 243000 bpp input 24 compressed 0.0000 link rate required 951750 available 972000
<7> [287.350780] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [287.351146] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:509:DDI A/PHY A] [CRTC:268:pipe B]
<7> [287.351554] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [287.351915] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] fastset requirement not met, forcing full modeset
<7> [287.352317] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:268:pipe B] releasing DPLL 0
<7> [287.352880] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:510:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [287.353295] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:509:DDI A/PHY A][CRTC:268:pipe B] DP link limits: pixel clock 317250 kHz DSC off max lanes 4 max rate 270000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000
<7> [287.353640] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 243000 bpp input 24 compressed 0.0000 link rate required 951750 available 972000
<7> [287.353975] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [287.354329] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:509:DDI A/PHY A] [CRTC:268:pipe B]
<7> [287.354715] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [287.355075] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] fastset requirement not met, forcing full modeset
<7> [287.355435] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:268:pipe B] releasing DPLL 0
<7> [287.355885] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:268:pipe B] allocated DPLL 0
<7> [287.356221] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:268:pipe B] reserving DPLL 0
<7> [287.356612] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:268:pipe B] enable: yes [modeset]
<7> [287.356981] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [287.357345] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: B, pipe bpp: 24, dithering: 0
<7> [287.357739] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [287.358084] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [287.358465] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [287.358840] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [287.359185] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 8213845, data_n: 8388608, link_m: 684487, link_n: 524288, tu: 64
<7> [287.359572] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [287.359942] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: enabled
<7> [287.360295] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [287.360630] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [287.360967] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [287.361315] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [287.361653] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [287.362029] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [287.362379] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [287.362700] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [287.363014] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [287.363345] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [287.363655] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [287.363963] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [287.364283] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1271, vmax: 1271, flipline: 1271, pipeline full: 0, guardband: 69 vsync start: 68, vsync end: 62
<7> [287.364590] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1202, vmax vblank: 1202, vmin vtotal: 1271, vmax vtotal: 1271
<7> [287.364895] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [287.365197] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x48 0xa
<7> [287.365564] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x48 0xa
<7> [287.365923] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=317250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1200 vb=1202-1271 vs=1203-1209 vt=1271, flags=0xa
<7> [287.366286] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "1920x1200": 120 317250 1920 1968 2000 2080 1200 1203 1209 1271 0x40 0xa
<7> [287.366584] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=317250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1200 vb=1202-1271 vs=1203-1209 vt=1271, flags=0xa
<7> [287.366903] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 243000, pipe src: 1920x1200+0+0, pixel rate 317250, min cdclk 158625
<7> [287.367241] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 53, ips linetime: 0
<7> [287.367538] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [287.367834] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [287.368129] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [287.368457] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [287.368752] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 243000, fracen: yes,
<7> [287.369046] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] quot: 8192, rem: 0, den: 1,
<7> [287.369363] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 253, tx_clk_div: 2.
<7> [287.369653] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [287.369942] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [287.370247] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x34, pll[1] = 0x0, pll[2] = 0xda, pll[3] = 0x1
<7> [287.370540] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [287.370831] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [287.371123] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x20, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x2
<7> [287.371450] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0x8f, pll[18] = 0xe6, pll[19] = 0x23
<7> [287.371816] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [287.372109] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [287.372432] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [287.372723] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [287.373012] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [287.373315] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [287.373609] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [287.373901] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [287.374194] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [287.374531] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [287.374818] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [287.375105] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [287.375428] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [287.375716] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:152:plane 1B] fb: [FB:558] 1920x1200 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [287.376010] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [287.376375] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 1920.000000x1200.000000+0.000000+0.000000 dst: 1920x1200+0+0
<7> [287.376687] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:182:plane 2B] fb: [NOFB], visible: no
<7> [287.376974] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:212:plane 3B] fb: [NOFB], visible: no
<7> [287.377273] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:242:plane 4B] fb: [NOFB], visible: no
<7> [287.377560] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:252:plane 5B] fb: [NOFB], visible: no
<7> [287.377845] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:262:cursor B] fb: [NOFB], visible: no
<7> [287.378239] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [287.378603] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [287.379062] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR1
<7> [287.382639] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [287.383066] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [287.591525] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:510:eDP-1] set backlight PWM = 0
<7> [287.592143] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe B
<7> [287.602968] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turn panel power off
<7> [287.603530] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [287.603988] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [287.655257] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [287.655646] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x2, on? 1) for [CRTC:268:pipe B]
<7> [287.656061] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [287.656391] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:509:DDI A/PHY A] - long
<7> [287.656735] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [287.657265] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:509:DDI A/PHY A]
<7> [287.657728] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [287.658162] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [287.658665] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:152:plane 1B]
<7> [287.659288] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:509:DDI A/PHY A]
<7> [287.659590] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:518:DDI TC1/PHY TC1]
<7> [287.659879] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:520:DP-MST A]
<7> [287.660165] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:521:DP-MST B]
<7> [287.660493] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:522:DP-MST C]
<7> [287.660788] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:523:DP-MST D]
<7> [287.661064] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:531:DDI TC2/PHY TC2]
<7> [287.661376] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:533:DP-MST A]
<7> [287.661651] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:534:DP-MST B]
<7> [287.661927] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:535:DP-MST C]
<7> [287.662201] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:536:DP-MST D]
<7> [287.662539] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:540:DDI TC3/PHY TC3]
<7> [287.662812] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:542:DP-MST A]
<7> [287.663085] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:543:DP-MST B]
<7> [287.663394] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:544:DP-MST C]
<7> [287.663665] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:545:DP-MST D]
<7> [287.663938] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:549:DDI TC4/PHY TC4]
<7> [287.664312] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [287.665391] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x2, on? 0) for [CRTC:268:pipe B]
<7> [287.665841] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [287.667515] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turn panel power on
<7> [287.667872] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power cycle (488 ms remaining)
<7> [288.159424] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [288.200500] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [288.200906] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power on
<7> [288.201359] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [288.226321] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [288.226712] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:509:DDI A/PHY A] - long
<7> [288.227059] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [288.227511] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:509:DDI A/PHY A]
<7> [288.404383] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [288.404817] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turning VDD on
<7> [288.405261] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [288.407503] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 0a c4 41 00 10 01 c0 02 00 00 00 1f 0b 80
<7> [288.408409] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [288.409291] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 02
<7> [288.410529] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [288.411445] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [288.412643] xe 0000:00:02.0: [drm:intel_dp_get_adjust_train [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0
<7> [288.413046] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0
<7> [288.414755] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Clock recovery OK
<7> [288.415112] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [288.416645] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [288.416996] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:510:eDP-1][ENCODER:509:DDI A/PHY A][DPRX] Link Training passed at link rate = 243000, lane count = 4
<7> [288.417906] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe B
<7> [288.418406] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [288.418781] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe B
<7> [288.419206] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:510:eDP-1] set backlight PWM = 13892
<7> [288.426998] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [288.428840] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:510:eDP-1]
<7> [288.429319] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:268:pipe B]
<7> [288.432408] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [288.432650] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.enable (expected yes, found no)
<7> [288.433081] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.active (expected yes, found no)
<7> [288.433527] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in cpu_transcoder (expected 1, found -1)
<7> [288.433938] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in lane_count (expected 4, found 0)
<7> [288.434361] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in dp_m_n (expected tu 64 data 8213845/8388608 link 684487/524288, found tu 0, data 0/0 link 0/0)
<7> [288.434786] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [288.435230] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [288.435639] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 1920, found 0)
<7> [288.436020] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 2080, found 0)
<7> [288.436473] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 1920, found 0)
<7> [288.436859] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 2080, found 0)
<7> [288.437258] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 1968, found 0)
<7> [288.437595] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2000, found 0)
<7> [288.437931] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1200, found 0)
<7> [288.438276] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1203, found 0)
<7> [288.438609] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1209, found 0)
<7> [288.438941] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1271, found 0)
<7> [288.439287] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1271, found 0)
<7> [288.439655] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 1920, found 0)
<7> [288.439999] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 2080, found 0)
<7> [288.440359] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 1920, found 0)
<7> [288.440689] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 2080, found 0)
<7> [288.441019] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 1968, found 0)
<7> [288.441368] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2000, found 0)
<7> [288.441682] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1200, found 0)
<7> [288.441995] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1203, found 0)
<7> [288.442407] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1209, found 0)
<7> [288.442725] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1271, found 0)
<7> [288.443081] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1271, found 0)
<7> [288.443434] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [288.443751] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [288.444068] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [288.444417] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in enhanced_framing (expected yes, found no)
<7> [288.444736] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in pipe_bpp (expected 24, found 0)
<7> [288.445053] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 317250, found 0)
<7> [288.445402] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 317250, found 0)
<7> [288.445719] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in port_clock (expected 243000, found 0)
<7> [288.446080] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:268:pipe B] fastset requirement not met in vrr.guardband (expected 69, found 0)
<7> [288.446429] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:268:pipe B] fastset requirement not met, forcing full modeset
<7> [288.446750] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:268:pipe B] releasing DPLL 0
<7> [288.447197] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [288.447473] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:268:pipe B] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x2 -> 0x0
<7> [288.447788] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:152:plane 1B] ddb ( 0 - 4032) -> ( 0 - 0), size 4032 -> 0
<7> [288.448031] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:262:cursor B] ddb (4032 - 4096) -> ( 0 - 0), size 64 -> 0
<7> [288.448303] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:152:plane 1B] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [288.448538] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:152:plane 1B] lines 1, 16, 17, 19, 19, 19, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [288.448774] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:152:plane 1B] blocks 16, 256, 272, 304, 304, 304, 0, 0, 30, 48, 62 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [288.449006] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:152:plane 1B] min_ddb 19, 283, 301, 336, 336, 336, 0, 0, 31, 54, 63 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [288.449324] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:268:pipe B] data rate 0 num active planes 0
<7> [288.449309] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [288.449676] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [288.449814] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [288.450020] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [288.450241] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [288.450393] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 42130 required 0 qgv_peak_bw: 38400
<7> [288.450809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 45877 required 0 qgv_peak_bw: 38400
<7> [288.451141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [288.451534] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:268:pipe B] min cdclk: 158625 kHz -> 0 kHz
<7> [288.451913] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 19829 kHz -> 0 kHz
<7> [288.452301] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [288.452634] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [288.452967] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [288.453419] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:268:pipe B] enable: no [modeset]
<7> [288.453760] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:152:plane 1B] fb: [NOFB], visible: no
<7> [288.454097] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:182:plane 2B] fb: [NOFB], visible: no
<7> [288.454466] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:212:plane 3B] fb: [NOFB], visible: no
<7> [288.454800] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:242:plane 4B] fb: [NOFB], visible: no
<7> [288.455130] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:252:plane 5B] fb: [NOFB], visible: no
<7> [288.455506] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:262:cursor B] fb: [NOFB], visible: no
<7> [288.455957] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [288.456334] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [288.456770] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [288.457700] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [288.458050] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [288.663562] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:510:eDP-1] set backlight PWM = 0
<7> [288.664352] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe B
<7> [288.669719] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 turn panel power off
<7> [288.670147] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [288.670564] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:509:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [288.721685] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [288.722052] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x2, on? 1) for [CRTC:268:pipe B]
<7> [288.723002] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [288.722993] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [288.723366] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:509:DDI A/PHY A] - long
<7> [288.723426] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [288.723701] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [288.723854] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:509:DDI A/PHY A]
<7> [288.724121] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:509:DDI A/PHY A]
<7> [288.724178] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:518:DDI TC1/PHY TC1]
<7> [288.724471] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:520:DP-MST A]
<7> [288.724780] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:521:DP-MST B]
<7> [288.725084] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:522:DP-MST C]
<7> [288.725419] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:523:DP-MST D]
<7> [288.725716] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:531:DDI TC2/PHY TC2]
<7> [288.726010] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:533:DP-MST A]
<7> [288.726333] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:534:DP-MST B]
<7> [288.726619] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:535:DP-MST C]
<7> [288.726933] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:536:DP-MST D]
<7> [288.727218] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:540:DDI TC3/PHY TC3]
<7> [288.727488] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:542:DP-MST A]
<7> [288.727757] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:543:DP-MST B]
<7> [288.728026] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:544:DP-MST C]
<7> [288.728331] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:545:DP-MST D]
<7> [288.728597] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:549:DDI TC4/PHY TC4]
<7> [288.728864] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:510:eDP-1]
<7> [288.729226] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [288.729491] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [288.729748] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [288.730216] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_B
<7> [288.730643] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:268:pipe B]
<7> [288.730969] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [288.731394] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [288.731741] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<6> [288.736782] [IGT] kms_pipe_crc_basic: finished subtest pipe-B-eDP-1, SUCCESS
|