Results for igt@kms_pm_rpm@dpms-lpsp

Result: Pass

i915_display_info10 igt_runner10 results10.json results10-xe-load.json guc_logs10.tar i915_display_info_post_exec10 boot10 dmesg10

DetailValue
Duration 1.43 seconds
Hostname 
shard-lnl-7
Igt-Version 
IGT-Version: 2.3-gf7b9a7230 (x86_64) (Linux: 6.19.0-rc2-lgci-xe-xe-4298-87b84fb15a5b9a631+ x86_64)
Out 
Using IGT_SRANDOM=1766558228 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
Starting subtest: dpms-lpsp
Subtest dpms-lpsp: SUCCESS (1.432s)
Err 
Starting subtest: dpms-lpsp
Subtest dpms-lpsp: SUCCESS (1.432s)
Dmesg
<6> [146.457855] Console: switching to colour dummy device 80x25
<6> [146.458056] [IGT] kms_pm_rpm: executing
<7> [146.463079] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [146.463089] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [146.463341] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [146.463431] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [146.463664] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [146.463667] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [146.463788] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [146.463904] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [146.464178] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [146.464181] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [146.464290] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [146.464370] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [146.464608] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]
<7> [146.464611] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]
<7> [146.465046] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [146.465353] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [146.465456] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [146.465558] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [146.465697] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [146.465704] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [146.465707] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [146.465709] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [146.465712] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [146.465715] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [146.465718] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor
<5> [146.465722] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [146.465724] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0
<5> [146.465727] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [146.465748] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes
<7> [146.466014] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [146.466170] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [146.467085] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [146.467087] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [146.467088] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [146.467144] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:
<7> [146.467148] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [146.467152] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [146.467165] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [146.467169] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [146.467309] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [146.467320] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [146.467324] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [146.467440] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [146.467448] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [146.467450] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [146.467548] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [146.467562] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]
<7> [146.467564] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]
<7> [146.467985] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [146.468284] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [146.468378] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [146.468471] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [146.468575] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [146.468577] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [146.468578] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [146.468579] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [146.468581] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [146.468583] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [146.468584] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor
<5> [146.468585] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [146.468586] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0
<5> [146.468588] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [146.468596] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes
<7> [146.468677] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [146.468775] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [146.469476] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [146.469478] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [146.469480] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [146.469540] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:
<7> [146.469544] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [146.469549] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [146.469599] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [146.469603] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [146.469756] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [146.469782] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [146.469784] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [146.469893] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [146.469920] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [146.469922] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [146.470023] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [146.479514] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:428]
<7> [147.496296] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [147.496561] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [147.496893] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [147.497217] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [147.497489] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [147.497741] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [147.498010] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [147.498238] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [147.498507] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [147.498745] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [147.499044] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [147.499277] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [147.499506] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [147.499737] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [147.499973] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [147.500196] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [147.500414] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [147.500632] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [147.500863] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [147.501129] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [147.501355] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [147.501608] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [147.501851] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [147.502154] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [147.502331] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [147.502410] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [147.502311] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [147.502448] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [147.502663] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [147.502945] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [147.503218] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [147.503473] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [147.503744] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [147.504095] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [147.504373] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [147.504651] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [147.505003] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [147.505285] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [147.505554] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [147.505821] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [147.506121] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [147.506404] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [147.506649] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [147.506889] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:149:pipe A] releasing DPLL 0
<7> [147.507279] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [147.507506] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [147.507741] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [147.507938] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [147.508108] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [147.508264] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [147.508417] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [147.508595] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [147.508800] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [147.509089] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [147.509334] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [147.509540] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [147.509743] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [147.509947] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [147.510165] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [147.510399] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [147.510612] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [147.510788] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [147.511004] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [147.511210] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: no [modeset]
<7> [147.511375] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [NOFB], visible: no
<7> [147.511538] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [147.511701] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [147.511857] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [147.512051] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [147.512208] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [147.512423] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [147.512583] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [147.512790] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [147.513502] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [147.513632] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [147.718195] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 0
<7> [147.718819] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [147.724303] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power off
<7> [147.724598] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [147.724894] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [147.724748] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [147.725463] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [147.777207] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [147.777751] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [147.786027] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [147.786427] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:149:pipe A]
<7> [147.786577] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [147.787315] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [147.787733] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [147.788201] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [147.788665] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [147.788980] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [147.789257] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [147.789584] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [147.789846] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [147.790140] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [147.790394] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [147.790643] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [147.790943] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [147.791190] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [147.791430] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [147.791722] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [147.791980] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [147.792221] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [147.792545] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [147.792792] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [147.793125] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [147.793558] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [147.794013] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [147.794324] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [147.794678] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [147.794954] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [147.795732] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [147.796089] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [147.814009] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [147.814401] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [147.814734] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [147.815141] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [147.818709] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspending
<7> [147.818698] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [147.819123] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [147.819508] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [147.819908] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [147.820596] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled
<7> [147.821498] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspended
<7> [147.821851] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspending
<7> [147.822362] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled
<7> [147.822714] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspended
<6> [147.898407] [IGT] kms_pm_rpm: starting subtest dpms-lpsp
<7> [147.912192] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resuming
<7> [147.913079] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled
<7> [147.917253] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resumed
<7> [147.917532] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resuming
<7> [147.917973] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled
<7> [147.918275] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resumed
<7> [147.921294] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [147.921848] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [147.922375] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [147.922736] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [147.923147] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [147.923453] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [147.923817] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [148.974331] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [148.974448] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [148.974569] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [148.975609] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [148.975701] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspending
<7> [148.976125] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled
<7> [148.976317] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspended
<7> [148.976501] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspending
<7> [148.976806] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled
<7> [148.977028] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspended
<7> [149.040587] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resuming
<7> [149.041042] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled
<7> [149.041557] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resumed
<7> [149.041789] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resuming
<7> [149.042081] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled
<7> [149.042285] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resumed
<7> [149.042759] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [149.042851] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:391:eDP-1]
<7> [149.043091] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [149.043418] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [149.043702] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [149.043995] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [149.044334] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [149.044611] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [149.044882] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [149.045174] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [149.045441] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [149.045714] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [149.045978] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [149.046286] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [149.046540] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [149.046814] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [149.047112] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [149.047379] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [149.047618] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [149.047856] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [149.048117] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [149.048399] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [149.048638] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [149.048892] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [149.049154] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [149.049386] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [149.049615] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [149.049878] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [149.050129] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [149.050352] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [149.050596] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [149.050849] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [149.051083] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [149.051353] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [149.051604] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [149.051828] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [149.052052] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [149.052270] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [149.052480] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [149.052692] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [149.052903] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [149.053135] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [149.053336] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [149.053535] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [149.053739] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [149.053947] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [149.054229] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [149.054563] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [149.054738] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [149.054921] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [149.055082] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [149.055208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [149.055332] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [149.055452] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [149.055584] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [149.055726] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [149.055899] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [149.056078] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [149.056259] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [149.056431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [149.056612] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [149.056779] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [149.056957] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [149.057119] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [149.057257] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [149.057389] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [149.057550] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:149:pipe A] allocated DPLL 0
<7> [149.057683] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:149:pipe A] reserving DPLL 0
<7> [149.057818] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [modeset]
<7> [149.057945] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [149.058087] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [149.058206] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [149.058320] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [149.058433] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [149.058545] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [149.058671] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [149.058799] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [149.058907] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [149.059019] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [149.059120] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [149.059222] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [149.059319] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [149.059419] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [149.059516] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [149.059613] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [149.059707] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [149.059801] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [149.059889] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [149.059978] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [149.060076] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [149.060172] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [149.060267] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [149.060358] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [149.060439] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [149.060517] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [149.060596] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [149.060674] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [149.060752] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [149.060827] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [149.060900] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [149.060974] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [149.061058] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [149.061133] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [149.061211] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [149.061285] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [149.061358] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [149.061430] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [149.061503] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [149.061569] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [149.061636] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [149.061703] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [149.061769] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [149.061841] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [149.061914] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [149.061987] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [149.062077] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [149.062171] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [149.062256] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [149.062340] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [149.062419] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [149.062487] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [149.062554] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [149.062621] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [149.062694] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [149.062767] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [149.062839] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:428] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [149.062913] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [149.062987] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [149.063078] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [149.063167] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [149.063241] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [149.063313] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [149.063385] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [149.065795] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [149.066038] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [149.066182] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [149.066328] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [149.066426] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [149.066516] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [149.066605] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [149.066676] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [149.066743] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [149.066804] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [149.066864] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [149.066928] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [149.066992] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [149.067072] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [149.067142] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [149.067209] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [149.067271] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [149.067332] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [149.067394] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [149.067482] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [149.067636] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [149.067699] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [149.067808] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [149.069130] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:149:pipe A]
<7> [149.069249] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [149.070956] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power on
<7> [149.071048] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [149.071154] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [149.081347] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [149.081472] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power on
<7> [149.081573] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [149.118092] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [149.118640] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [149.119091] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [149.119532] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [149.294223] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [149.294605] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on
<7> [149.294895] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [149.296956] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [149.298282] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [149.299088] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [149.300320] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [149.301672] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [149.303564] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Clock recovery OK
<7> [149.304000] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [149.305644] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [149.306080] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [149.307039] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [149.307544] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [149.307891] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [149.308316] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 4518
<7> [149.324421] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [149.326208] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [149.326606] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [149.329243] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [149.329623] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [149.330487] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [149.330973] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<6> [149.331541] [IGT] kms_pm_rpm: finished subtest dpms-lpsp, SUCCESS
<7> [149.331417] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [149.331721] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [149.332091] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [149.332380] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [149.332731] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [149.333184] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:428] from all active usage due to RMFB ioctl
<7> [149.333841] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:428] is removed
<7> [149.333983] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [149.334366] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [149.334647] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [149.334943] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [149.335293] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [149.335622] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [149.335982] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [149.336414] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [149.336759] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [149.337109] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [149.337450] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [149.339515] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [149.340056] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [149.340438] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [149.364497] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [149.364772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [149.365001] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [149.365284] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [149.365495] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [149.365754] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [149.366062] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [149.366390] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [149.366668] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [149.366926] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [149.367248] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [149.374341] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [149.376316] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [149.376855] [IGT] kms_pm_rpm: exiting, ret=0
<6> [149.391655] Console: switching to colour frame buffer device 180x56
<7> [149.442175] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [149.442517] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [149.442777] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
Created at 2025-12-24 07:15:51