Results for igt@kms_frontbuffer_tracking@fbc-1p-primscrn-pri-indfb-draw-blt

Result: Pass

i915_display_info21 igt_runner21 results21.json results21-xe-load.json guc_logs21.tar i915_display_info_post_exec21 boot21 dmesg21

DetailValue
Duration 3.08 seconds
Hostname
shard-lnl-1
Igt-Version
IGT-Version: 2.3-gf38f4d8e9 (x86_64) (Linux: 6.19.0-rc1-lgci-xe-xe-4294-92cfd765fcc4d84db+ x86_64)
Out
Using IGT_SRANDOM=1766441317 for randomisation
Opened device: /dev/dri/card0
FBC last action not supported
Can't test DRRS: Not supported.
Starting subtest: fbc-1p-primscrn-pri-indfb-draw-blt
Subtest fbc-1p-primscrn-pri-indfb-draw-blt: SUCCESS (3.081s)
Err
Starting subtest: fbc-1p-primscrn-pri-indfb-draw-blt
Subtest fbc-1p-primscrn-pri-indfb-draw-blt: SUCCESS (3.081s)
Dmesg
<6> [193.334083] Console: switching to colour dummy device 80x25
<6> [193.334293] [IGT] kms_frontbuffer_tracking: executing
<7> [193.339666] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [193.339675] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [193.339836] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [193.340053] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [193.340055] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [193.340170] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [193.340373] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [193.340376] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [193.340485] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [193.340760] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]
<7> [193.340763] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]
<7> [193.341205] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [193.341512] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [193.341613] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [193.341709] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [193.341814] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [193.341818] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [193.341819] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [193.341820] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [193.341823] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [193.341824] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [193.341825] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor
<5> [193.341827] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [193.341828] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0
<5> [193.341830] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [193.341840] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes
<7> [193.341917] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [193.341992] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [193.342496] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [193.342498] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [193.342499] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [193.342563] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:
<7> [193.342567] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [193.342571] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [193.342584] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [193.342588] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [193.342727] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [193.342739] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [193.342742] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [193.342867] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [193.342875] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [193.342877] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [193.342980] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [193.347365] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [193.347525] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]
<7> [193.347653] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [193.347791] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [193.348255] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]
<6> [193.349480] [IGT] kms_frontbuffer_tracking: starting subtest fbc-1p-primscrn-pri-indfb-draw-blt
<7> [193.350002] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to f
<7> [193.350094] xe 0000:00:02.0: [drm:intel_psr_debug_set [xe]] Invalid debug mask f
<7> [193.350187] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to 1
<7> [193.350328] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [193.350439] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [193.350545] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [193.350657] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [193.350752] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [193.350857] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [193.350972] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset]
<7> [193.351066] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [193.351159] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [193.351242] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [193.351321] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [193.351399] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [193.351476] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [193.351574] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [193.351675] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [193.351773] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [193.351863] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [193.351938] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [193.352012] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [193.352085] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [193.352159] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [193.352232] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [193.352305] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [193.352378] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [193.352451] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [193.352533] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [193.352627] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [193.352728] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [193.352820] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [193.352894] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [193.352965] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [193.353036] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [193.353106] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [193.353179] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [193.353252] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [193.353325] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [193.353398] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [193.353470] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [193.353561] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [193.353654] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [193.353748] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [193.353835] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [193.353908] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [193.353977] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [193.354047] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [193.354116] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [193.354186] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [193.354255] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.354324] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.354393] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.354462] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [193.354539] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [193.354627] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.354716] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.354804] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.354877] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [193.354944] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [193.355012] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:392] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [193.355081] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [193.355148] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [193.355237] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [193.355322] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [193.355456] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [193.374654] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [193.374801] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [193.380230] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:430]
<7> [193.380335] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:431]
<7> [193.380441] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:432]
<7> [193.380585] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:433]
<7> [193.381130] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:434]
<7> [193.491177] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [193.491317] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [193.491678] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [193.491956] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [193.492226] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [193.492488] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [193.492793] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [193.493053] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [193.493309] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [193.493576] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [193.493821] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [193.494064] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [193.494313] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [193.494576] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [193.494820] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [193.495104] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [193.495337] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [193.495645] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [193.495877] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [193.496148] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [193.496383] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [193.496666] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [193.496886] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [193.497111] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [193.497340] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [193.497608] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [193.497851] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [193.498084] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [193.498310] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [193.498546] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [193.498768] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [193.498993] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [193.499254] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [193.499476] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [193.499751] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [193.499975] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [193.500195] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [193.500424] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [193.500688] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [193.500911] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [193.501127] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:149:pipe A] releasing DPLL 0
<7> [193.501448] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [193.501842] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [193.502058] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [193.502262] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [193.502439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [193.502642] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [193.502835] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [193.503003] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [193.503215] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [193.503453] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [193.503714] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [193.503949] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [193.504167] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [193.504371] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [193.504598] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [193.504818] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [193.505013] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [193.505207] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [193.505415] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [193.505641] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: no [modeset]
<7> [193.505814] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [NOFB], visible: no
<7> [193.505990] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [193.506160] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [193.506324] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [193.506497] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [193.506690] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [193.507023] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [193.507179] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [193.715729] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 0
<7> [193.716437] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [193.727028] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power off
<7> [193.727345] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [193.727696] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [193.780016] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [193.780567] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [193.788490] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [193.788915] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:149:pipe A]
<7> [193.789054] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [193.790162] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [193.790584] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [193.791004] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [193.791258] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [193.791490] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [193.791801] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [193.792035] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [193.792273] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [193.792523] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [193.792752] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [193.793005] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [193.793211] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [193.793414] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [193.793645] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [193.793893] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [193.794090] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [193.794409] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [193.794635] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [193.794850] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [193.795217] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [193.795561] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [193.795809] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [193.796109] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [193.796323] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [193.801617] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [193.805316] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [193.810896] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:427]
<7> [193.817135] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [193.817320] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [193.817409] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [193.817527] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [193.826546] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [193.826714] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [193.826833] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [193.827130] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [193.827156] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:391:eDP-1]
<7> [193.827225] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [193.827339] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [193.827429] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [193.827540] xe 0000:00:02.0: [drm:intel_psr_compute_config [xe]] PSR disabled by flag
<7> [193.827639] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [193.827755] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [193.827855] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [193.827940] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [193.828023] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [193.828105] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [193.828186] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [193.828266] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [193.828345] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [193.828423] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [193.828508] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [193.828606] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [193.828705] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [193.828803] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [193.828886] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [193.828960] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [193.829036] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [193.829113] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [193.829191] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [193.829267] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [193.829342] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [193.829416] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [193.829489] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [193.829635] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [193.829732] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [193.829826] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [193.829905] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [193.829977] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [193.830050] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [193.830121] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [193.830192] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [193.830263] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [193.830333] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [193.830403] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [193.830472] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [193.830568] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [193.830660] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [193.830749] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [193.830832] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [193.830905] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [193.830977] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [193.831450] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [193.831541] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [193.831640] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [193.831725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [193.831805] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [193.831871] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [193.831931] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [193.831990] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [193.832058] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [193.832141] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [193.832221] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [193.832299] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [193.832378] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [193.832457] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [193.832548] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [193.832667] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [193.832779] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [193.832877] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [193.832962] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [193.833055] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:149:pipe A] allocated DPLL 0
<7> [193.833130] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:149:pipe A] reserving DPLL 0
<7> [193.833208] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [modeset]
<7> [193.833288] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [193.833367] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [193.833444] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [193.833532] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [193.833632] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [193.833730] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [193.833823] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [193.833899] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [193.833973] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [193.834045] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [193.834117] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled
<7> [193.834189] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [193.834259] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [193.834331] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [193.834401] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [193.834472] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [193.834559] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [193.834653] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [193.834746] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [193.834834] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [193.834907] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [193.834977] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [193.835048] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [193.835118] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [193.835188] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [193.835258] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [193.835328] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [193.835397] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [193.835468] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [193.835567] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [193.835663] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [193.835757] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [193.835844] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [193.835918] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [193.835988] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [193.836058] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [193.836128] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [193.836199] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [193.836269] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [193.836338] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [193.836408] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.836476] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.836570] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.836660] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [193.836756] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [193.836851] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.836931] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.836999] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [193.837067] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [193.837134] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [193.837202] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:427] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x100000000000001, visible: yes
<7> [193.837271] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [193.837339] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [193.837408] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [193.837476] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [193.837558] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [193.837638] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [193.837715] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [193.838100] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [193.838350] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [193.838487] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [193.838652] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [193.838768] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [193.838865] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [193.838947] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [193.839011] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [193.839074] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [193.839135] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [193.839194] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [193.839254] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [193.839315] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [193.839375] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [193.839433] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [193.839493] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [193.839571] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [193.839636] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [193.839698] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [193.839783] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [193.839940] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [193.840000] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [193.840101] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [193.841528] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:149:pipe A]
<7> [193.841635] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [193.843313] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power on
<7> [193.843390] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power cycle (446 ms remaining)
<7> [194.291730] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060
<7> [194.379597] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [194.379691] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [194.379707] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [194.379720] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [194.380007] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power on
<7> [194.380279] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [194.416617] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [194.417009] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [194.417316] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [194.417642] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [194.585451] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [194.585855] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on
<7> [194.586137] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [194.588359] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [194.589794] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [194.590737] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [194.591880] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [194.593105] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [194.594202] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Clock recovery OK
<7> [194.594546] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [194.595990] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [194.596348] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [194.597204] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [194.597698] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [194.598061] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [194.598535] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 4518
<7> [194.614853] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [194.615446] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [194.619685] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [194.648547] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [194.649175] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [194.649721] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [194.682370] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [194.682909] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [194.699652] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:427] from all active usage due to RMFB ioctl
<7> [194.699811] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:427] is removed
<7> [194.699985] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [194.700460] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [194.700860] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [194.701180] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [194.701508] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [194.701894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [194.702360] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [194.702837] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [194.703273] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [194.703711] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [194.704137] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [194.734063] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [194.734310] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [194.734436] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [194.734564] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:427]
<7> [194.735255] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:437]
<7> [194.736767] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:438]
<7> [194.745404] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:439]
<7> [194.880348] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [194.880478] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [194.964643] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [194.964712] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:391:eDP-1]
<7> [194.964864] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [194.965115] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [194.965324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [194.965570] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [194.965768] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [194.966077] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [194.966341] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [194.966624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [194.966873] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [194.967124] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [194.967383] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [194.985202] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [194.989380] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [195.015573] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.015932] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.048536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [195.048854] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [195.049139] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [195.081535] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [195.081880] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [195.097929] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [195.097989] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:391:eDP-1]
<7> [195.114787] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.148541] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [195.148878] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [195.149163] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [195.182048] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [195.182515] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [195.198110] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [195.198199] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:391:eDP-1]
<7> [195.214991] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.248644] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [195.248994] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [195.249282] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [195.281973] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [195.282330] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [195.298074] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [195.298165] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:391:eDP-1]
<7> [195.314911] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.348646] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [195.349039] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [195.349345] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [195.382082] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [195.382440] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [195.404695] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:439] from all active usage due to RMFB ioctl
<7> [195.404770] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:439] is removed
<7> [195.404845] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [195.405128] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [195.405370] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [195.405709] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [195.405957] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [195.406198] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [195.406513] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [195.406812] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [195.407120] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [195.407431] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [195.407841] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [195.514845] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [195.514974] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:391:eDP-1]
<7> [195.515249] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [195.515763] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [195.516090] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [195.516392] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [195.516716] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [195.517207] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [195.517708] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [195.518153] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [195.518624] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [195.519053] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [195.519489] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [195.522755] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 14745600 bytes of contiguous stolen space for FBC, limit: 2
<7> [195.523109] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]
<7> [195.539203] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [195.543973] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [195.566678] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.567442] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.598542] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [195.599256] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [195.599876] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [195.632155] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [195.632850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [195.653906] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.682561] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [195.683186] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [195.683746] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [195.715319] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [195.715844] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [195.749261] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.781536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [195.782220] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [195.782810] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [195.815304] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [195.815938] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [195.835276] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.865531] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [195.866211] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [195.866805] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [195.898707] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [195.899387] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [195.931518] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [195.931934] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [195.932249] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [195.933591] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [195.934565] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [195.934848] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [195.966648] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [195.967170] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [195.967616] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [195.998784] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [195.999237] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [196.016337] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [196.048646] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [196.049140] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [196.049577] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [196.081970] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [196.082304] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [196.111568] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [196.131533] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [196.132145] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [196.132820] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [196.165436] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [196.166132] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [196.185343] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [196.215536] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [196.216185] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [196.216763] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [196.248778] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [196.249339] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [196.276422] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [196.299635] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [196.300030] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [196.300388] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [196.331272] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [196.331672] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [196.349243] xe 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [xe]] Re-arming FIFO underruns on pipe A
<7> [196.382629] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [196.382951] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [196.383233] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [196.414581] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [196.414926] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<6> [196.431897] [IGT] kms_frontbuffer_tracking: finished subtest fbc-1p-primscrn-pri-indfb-draw-blt, SUCCESS
<7> [196.433407] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:430] from all active usage due to RMFB ioctl
<7> [196.433560] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:430] is removed
<7> [196.433663] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [196.434029] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [196.434307] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [196.434616] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [196.434880] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [196.435193] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [196.435603] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [196.435971] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [196.436328] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [196.436756] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [196.437107] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [196.447496] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]
<7> [196.474449] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [196.474874] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [196.475182] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [196.475492] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [196.475772] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [196.476103] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [196.476552] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [196.476991] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [196.477379] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [196.477809] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [196.478242] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [196.480516] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 11059200 bytes of contiguous stolen space for FBC, limit: 2
<7> [196.480889] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:33:plane 1A]
<7> [196.498176] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [196.498873] [IGT] kms_frontbuffer_tracking: exiting, ret=0
<7> [196.499252] xe 0000:00:02.0: [drm:i915_edp_psr_debug_set [xe]] Setting PSR debug to 0
<7> [196.501019] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [196.501574] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [196.502031] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [196.502502] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [196.503008] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [196.503596] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [fastset]
<7> [196.504067] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [196.504476] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [196.504863] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [196.505235] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [196.505766] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [196.506077] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [196.506381] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [196.506692] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [196.506972] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [196.507243] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [196.507517] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [196.507766] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [196.508008] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [196.508245] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [196.508662] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [196.508874] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [196.509081] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [196.509276] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [196.509505] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [196.509697] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [196.509875] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [196.510082] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [196.510271] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [196.510432] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [196.510617] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [196.510768] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [196.510942] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [196.511108] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [196.511254] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [196.511393] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [196.511546] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [196.511700] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [196.511844] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [196.511973] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [196.512103] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [196.512224] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [196.512341] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [196.512463] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [196.512592] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [196.512722] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [196.512844] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [196.512960] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [196.513076] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [196.513184] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [196.513291] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [196.513394] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [196.513534] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [196.513634] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [196.513730] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [196.513824] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [196.513916] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [196.514008] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [196.514099] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [196.514188] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [196.514274] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [196.514357] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [196.514440] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:392] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [196.514542] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [196.514631] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [196.530809] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:33:plane 1A]
<7> [196.547496] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [196.549387] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [196.549881] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<6> [196.565046] Console: switching to colour frame buffer device 180x56
<7> [196.581513] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [196.581894] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [196.582225] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [196.582575] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [196.582939] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [196.615615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [196.616007] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [196.616332] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
Created at 2025-12-22 22:16:01