Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

i915_display_info4 igt_runner4 results4.json results4-xe-load.json guc_logs4.tar i915_display_info_post_exec4 boot4 dmesg4

DetailValue
Duration 1.45 seconds
Hostname 
shard-lnl-5
Igt-Version 
IGT-Version: 2.3-gf38f4d8e9 (x86_64) (Linux: 6.19.0-rc1-lgci-xe-xe-4275-7493f64fc561cbde8+ x86_64)
Out 
Using IGT_SRANDOM=1766238974 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.447s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (1.447s)
Dmesg
<6> [513.965398] Console: switching to colour dummy device 80x25
<6> [513.965671] [IGT] kms_pm_rpm: executing
<7> [513.970745] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [513.970756] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [513.970942] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [513.971034] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [513.971264] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [513.971267] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [513.971388] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [513.971470] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [513.971697] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [513.971701] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [513.971815] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [513.971901] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [513.972143] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]
<7> [513.972146] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]
<7> [513.972584] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [513.973515] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [513.973626] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [513.973746] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [513.973871] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [513.973876] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [513.973879] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [513.973880] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [513.973883] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [513.973885] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [513.973887] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor
<5> [513.973889] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [513.973891] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0
<5> [513.973893] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [513.973907] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes
<7> [513.974013] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [513.974097] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [513.974605] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [513.974607] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [513.974608] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [513.974674] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:
<7> [513.974678] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [513.974682] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [513.974697] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [513.974700] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [513.974829] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [513.974839] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [513.974842] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [513.974954] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [513.974962] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [513.974965] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [513.975067] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [513.975081] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1]
<7> [513.975083] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:391:eDP-1]
<7> [513.975504] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00
<7> [513.975812] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [513.975909] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [513.976001] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [513.976112] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz
<5> [513.976114] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [513.976116] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [513.976117] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] DisplayID extension version 0x13, primary use 0x00
<7> [513.976118] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<5> [513.976120] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [513.976121] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD monitor
<5> [513.976123] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [513.976124] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:391:eDP-1] ELD size 20, SAD count 0
<5> [513.976126] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [513.976133] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] VRR capable: yes
<7> [513.976214] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [513.976297] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:391:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<5> [513.976789] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [513.976792] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<5> [513.976794] [drm] DisplayID checksum invalid, remainder is 248 (ignoring)
<7> [513.976836] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:391:eDP-1] probed modes:
<7> [513.976839] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [513.976843] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "2880x1800": 120 695310 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [513.976882] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1]
<7> [513.976885] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [513.977005] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected
<7> [513.977035] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2]
<7> [513.977038] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [513.977147] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:412:DP-2] disconnected
<7> [513.977173] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3]
<7> [513.977175] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [513.977272] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:420:DP-3] disconnected
<7> [513.986737] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:429]
<7> [515.002829] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [515.003176] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [515.003772] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [515.004243] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [515.004701] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [515.005180] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0)
<7> [515.005610] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [515.006058] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [515.006458] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0)
<7> [515.006891] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0)
<7> [515.007322] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0)
<7> [515.007736] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0)
<7> [515.008167] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0)
<7> [515.008551] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0)
<7> [515.008998] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [515.009376] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [515.009786] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [515.010218] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0)
<7> [515.010621] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0)
<7> [515.010989] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0)
<7> [515.011354] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0)
<7> [515.011757] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0)
<7> [515.012169] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0)
<7> [515.012553] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0)
<7> [515.013062] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0)
<7> [515.013444] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0)
<7> [515.013893] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [515.014244] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [515.014576] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [515.014953] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0)
<7> [515.015251] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0)
<7> [515.015548] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0)
<7> [515.015890] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [515.016159] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [515.016417] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [515.016695] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [515.016943] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0)
<7> [515.017201] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0)
<7> [515.017428] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 432000, found 0)
<7> [515.017672] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [515.017890] xe 0000:00:02.0: [drm:intel_dpll_crtc_put [xe]] [CRTC:149:pipe A] releasing DPLL 0
<7> [515.018203] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [515.018372] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [515.018594] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [515.018755] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb (4051 - 4096) -> ( 0 - 0), size 45 -> 0
<7> [515.018901] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [515.019044] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [515.019187] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [515.019324] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [515.019490] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [515.019725] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [515.019928] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [515.020123] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [515.020313] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [515.020495] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [515.020694] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 173855 kHz -> 0 kHz
<7> [515.020898] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 21732 kHz -> 0 kHz
<7> [515.021070] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [515.021233] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz
<7> [515.021415] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [515.021640] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: no [modeset]
<7> [515.021807] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [NOFB], visible: no
<7> [515.021956] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [515.022100] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [515.022243] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [515.022382] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [515.022519] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [515.022751] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [515.022922] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [515.023139] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [515.023895] xe 0000:00:02.0: [drm:intel_alpm_disable [xe]] Disabling ALPM
<7> [515.024017] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]]
<7> [515.024726] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [515.024773] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [515.024796] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [515.231788] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 0
<7> [515.232448] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A
<7> [515.243393] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power off
<7> [515.243802] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [515.243950] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [515.244386] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [515.244372] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [515.296333] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000
<7> [515.296657] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - short
<7> [515.300159] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [515.300657] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:149:pipe A]
<7> [515.300815] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [515.301357] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [515.302050] xe 0000:00:02.0: [drm:intel_dpll_disable [xe]] disabling DPLL 0
<7> [515.302632] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A
<7> [515.303183] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [515.303611] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [515.303951] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [515.304299] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [515.304630] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [515.304944] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [515.305288] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [515.305606] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [515.305960] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [515.306263] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [515.306552] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [515.306911] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [515.307236] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [515.307523] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [515.307966] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [515.308262] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: *)
<7> [515.308554] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1
<7> [515.309202] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A
<7> [515.309767] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [515.310117] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [515.310575] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [515.310894] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384
<7> [515.311885] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [515.312267] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [515.329858] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [515.330348] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [515.330842] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [515.331265] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [515.331718] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspending
<7> [515.332221] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled
<7> [515.332507] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspended
<7> [515.332831] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspending
<7> [515.333245] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled
<7> [515.333504] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspended
<6> [515.414263] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [515.447107] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resuming
<7> [515.447515] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled
<7> [515.448003] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resumed
<7> [515.448225] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resuming
<7> [515.448507] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled
<7> [515.448706] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resumed
<7> [515.448939] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [515.449165] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [515.449376] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [515.449594] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [515.450205] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [515.450424] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [515.450688] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [515.450850] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [515.451145] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B]
<7> [515.451171] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [515.451493] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [515.451687] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [515.451819] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [515.451974] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [515.452324] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [515.452501] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [515.452809] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [515.470838] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [515.471326] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [515.471827] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [516.495604] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [516.495592] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [516.495623] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling always-on
<7> [516.498353] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspending
<7> [516.498332] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [516.499050] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel disabled
<7> [516.499409] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT0: runtime suspended
<7> [516.499762] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspending
<7> [516.500268] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel disabled
<7> [516.500623] xe 0000:00:02.0: [drm:xe_gt_runtime_suspend [xe]] Tile0: GT1: runtime suspended
<7> [516.569136] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resuming
<7> [516.569696] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT0: GuC CT communication channel enabled
<7> [516.570447] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT0: runtime resumed
<7> [516.570832] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resuming
<7> [516.571249] xe 0000:00:02.0: [drm:guc_ct_change_state [xe]] Tile0: GT1: GuC CT communication channel enabled
<7> [516.571574] xe 0000:00:02.0: [drm:xe_gt_runtime_resume [xe]] Tile0: GT1: runtime resumed
<7> [516.572118] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A]
<7> [516.572231] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:391:eDP-1]
<7> [516.572605] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:391:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [516.573171] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:390:DDI A/PHY A][CRTC:149:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000
<7> [516.573658] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000
<7> [516.574116] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [516.574586] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:390:DDI A/PHY A] [CRTC:149:pipe A]
<7> [516.575048] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [516.575507] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [516.575937] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [516.576402] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [516.576875] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288)
<7> [516.577333] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [516.577786] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [516.578213] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880)
<7> [516.578633] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040)
<7> [516.579021] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880)
<7> [516.579385] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040)
<7> [516.579870] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928)
<7> [516.580272] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960)
<7> [516.580728] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [516.581098] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [516.581520] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [516.581871] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809)
<7> [516.582194] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906)
<7> [516.582529] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906)
<7> [516.582833] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880)
<7> [516.583154] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040)
<7> [516.583429] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880)
<7> [516.583738] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040)
<7> [516.584047] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928)
<7> [516.584294] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960)
<7> [516.584542] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [516.584777] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [516.584996] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [516.585208] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809)
<7> [516.585412] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906)
<7> [516.585646] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906)
<7> [516.585852] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [516.586041] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [516.586221] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [516.586404] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [516.586630] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710)
<7> [516.586800] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710)
<7> [516.586961] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:149:pipe A] fastset requirement not met in port_clock (expected 0, found 432000)
<7> [516.587121] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:149:pipe A] fastset requirement not met, forcing full modeset
<7> [516.587337] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling always-on
<7> [516.587555] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [516.587725] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:149:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [516.587906] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [516.588025] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:143:cursor A] ddb ( 0 - 0) -> (4051 - 4096), size 0 -> 45
<7> [516.588135] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [516.588240] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [516.588341] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [516.588439] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [516.588593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [516.588748] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [516.588894] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [516.589051] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [516.589203] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [516.589331] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [516.589455] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] [CRTC:149:pipe A] min cdclk: 0 kHz -> 173855 kHz
<7> [516.589628] xe 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [xe]] dbuf bandwidth min cdclk: 0 kHz -> 21732 kHz
<7> [516.589774] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] Can change cdclk via squashing
<7> [516.589909] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [516.590021] xe 0000:00:02.0: [drm:intel_cdclk_atomic_check [xe]] New voltage level calculated to be logical 0, actual 0
<7> [516.590157] xe 0000:00:02.0: [drm:intel_find_dpll [xe]] [CRTC:149:pipe A] allocated DPLL 0
<7> [516.590261] xe 0000:00:02.0: [drm:intel_dpll_crtc_get [xe]] [CRTC:149:pipe A] reserving DPLL 0
<7> [516.590369] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:149:pipe A] enable: yes [modeset]
<7> [516.590488] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [516.590610] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [516.590719] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid>
<7> [516.590824] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [516.590942] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0
<7> [516.591068] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0
<7> [516.591189] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64
<7> [516.591298] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [516.591404] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled
<7> [516.591512] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled
<7> [516.591629] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [516.591746] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0
<7> [516.591855] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [516.591949] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14
<7> [516.592041] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB
<7> [516.592132] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB
<7> [516.592221] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0
<7> [516.592307] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range
<7> [516.592394] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined
<7> [516.592484] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1
<7> [516.592576] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] framestart delay: 1, MSA timing delay: 0, set context latency: 0
<7> [516.592665] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, fixed rr: yes, vmin: 1906, vmax: 1906, flipline: 1906, pipeline full: 0, guardband: 104 vsync start: 103, vsync end: 97
<7> [516.592752] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1802, vmax vblank: 1802, vmin vtotal: 1906, vmax vtotal: 1906
<7> [516.592833] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [516.592914] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa
<7> [516.592994] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [516.593072] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa
<7> [516.593148] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa
<7> [516.593224] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710, min cdclk 173855
<7> [516.593306] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0
<7> [516.593390] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [516.593473] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [516.593579] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0
<7> [516.593678] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cx0pll_hw_state: lane_count: 4, ssc_enabled: no, use_c10: yes, tbt_mode: no
<7> [516.593756] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_hw_state: clock: 432000, fracen: no,
<7> [516.593828] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] multiplier: 225, tx_clk_div: 1.
<7> [516.593899] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] c10pll_rawhw_state:
<7> [516.593970] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] tx: 0x10, cmn: 0x21
<7> [516.594040] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[0] = 0x4, pll[1] = 0x0, pll[2] = 0xa2, pll[3] = 0x1
<7> [516.594111] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[4] = 0x0, pll[5] = 0x0, pll[6] = 0x0, pll[7] = 0x0
<7> [516.594182] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[8] = 0x0, pll[9] = 0x1, pll[10] = 0x0, pll[11] = 0x0
<7> [516.594253] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[12] = 0x0, pll[13] = 0x0, pll[14] = 0x0, pll[15] = 0x1
<7> [516.594322] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pll[16] = 0x85, pll[17] = 0xf, pll[18] = 0xe6, pll[19] = 0x23
<7> [516.594392] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [516.594461] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [516.594542] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [516.594614] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [516.594690] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [516.594759] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [516.594826] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [516.594893] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [516.594966] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [516.595043] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [516.595119] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [516.595194] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [516.595268] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [516.595344] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:33:plane 1A] fb: [FB:429] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [516.595413] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [516.595484] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0
<7> [516.595555] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:63:plane 2A] fb: [NOFB], visible: no
<7> [516.595633] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:93:plane 3A] fb: [NOFB], visible: no
<7> [516.595710] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:123:plane 4A] fb: [NOFB], visible: no
<7> [516.595780] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:133:plane 5A] fb: [NOFB], visible: no
<7> [516.595850] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:143:cursor A] fb: [NOFB], visible: no
<7> [516.597705] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [516.597805] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [516.597929] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A
<7> [516.598062] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [516.598150] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no)
<7> [516.598221] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480
<7> [516.598301] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:390:DDI A/PHY A]
<7> [516.598365] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:399:DDI TC1/PHY TC1]
<7> [516.598427] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:401:DP-MST A]
<7> [516.598496] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:402:DP-MST B]
<7> [516.598559] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:403:DP-MST C]
<7> [516.598629] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:411:DDI TC2/PHY TC2]
<7> [516.598703] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:413:DP-MST A]
<7> [516.598772] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:414:DP-MST B]
<7> [516.598841] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:415:DP-MST C]
<7> [516.598904] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:419:DDI TC3/PHY TC3]
<7> [516.598963] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:421:DP-MST A]
<7> [516.599020] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:422:DP-MST B]
<7> [516.599077] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:423:DP-MST C]
<7> [516.599153] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf
<7> [516.599292] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: *)
<7> [516.599348] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes)
<7> [516.599435] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A
<7> [516.600595] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:149:pipe A]
<7> [516.600699] xe 0000:00:02.0: [drm:intel_dpll_enable [xe]] enabling DPLL 0
<7> [516.601748] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turn panel power on
<7> [516.601822] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [516.601909] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [516.611621] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [516.611719] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 wait for panel power on
<7> [516.611817] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [516.648347] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010
<7> [516.648719] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:390:DDI A/PHY A] - long
<7> [516.649019] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [516.649558] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:390:DDI A/PHY A]
<7> [516.825885] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete
<7> [516.826261] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 turning VDD on
<7> [516.826635] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:390:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [516.828709] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80
<7> [516.830040] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [516.830958] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05
<7> [516.832262] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [516.833582] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [516.834794] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Clock recovery OK
<7> [516.835239] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Using DP training pattern TPS4
<7> [516.836802] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [516.837184] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:391:eDP-1][ENCODER:390:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4
<7> [516.838076] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A
<7> [516.838602] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]]
<7> [516.838988] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A
<7> [516.839422] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:391:eDP-1] set backlight PWM = 4518
<7> [516.855617] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [516.857536] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:391:eDP-1]
<7> [516.858001] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:149:pipe A]
<7> [516.860939] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:400:DP-1]
<7> [516.861545] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [516.862040] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [516.862502] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<6> [516.862959] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [516.863010] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [516.863411] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:412:DP-2]
<7> [516.863931] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [516.864298] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:420:DP-3]
<7> [516.864733] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:429] from all active usage due to RMFB ioctl
<7> [516.864781] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [516.865151] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:33:plane 1A] because [FB:429] is removed
<7> [516.865294] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 4051) -> ( 0 - 0), size 4051 -> 0
<7> [516.865663] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [516.865941] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [516.866208] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [516.866497] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [516.866915] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 0 num active planes 0
<7> [516.867261] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400
<7> [516.867593] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400
<7> [516.867896] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [516.868172] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400
<7> [516.868485] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0
<7> [516.870668] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [516.871059] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [516.871344] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2
<7> [516.895070] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:33:plane 1A] ddb ( 0 - 0) -> ( 0 - 4051), size 0 -> 4051
<7> [516.895505] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [516.895841] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 13, 13, 13, 13, 13, 0, 0, 0, 3, 0
<7> [516.896153] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 24, 313, 313, 313, 313, 313, 0, 0, 38, 73, 87
<7> [516.896530] xe 0000:00:02.0: [drm:skl_print_plane_changes [xe]] [PLANE:33:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 28, 346, 346, 346, 346, 346, 0, 0, 39, 82, 88
<7> [516.896935] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:149:pipe A] data rate 1390840 num active planes 1
<7> [516.897381] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400
<7> [516.897857] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400
<7> [516.898319] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [516.898781] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400
<7> [516.899257] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461
<7> [516.905499] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2
<7> [516.907387] xe 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [516.908266] [IGT] kms_pm_rpm: exiting, ret=0
<6> [516.922967] Console: switching to colour frame buffer device 180x56
<7> [516.939615] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [516.940123] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [516.940582] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
<7> [516.941040] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off
<7> [516.941534] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00
<7> [516.973624] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off
<7> [516.974114] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6
<7> [516.974571] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02
Created at 2025-12-20 14:27:45